NSF Product and Service Listings

These NSF Official Listings are current as of Wednesday, January 17, 2018 at 12:15 a.m. Eastern Time. Please contact NSF International to confirm the status of any Listing, report errors, or make suggestions.

Alert: NSF is concerned about fraudulent downloading and manipulation of website text. Always confirm this information by clicking on the below link for the most accurate information: http://info.nsf.org/Certified/food/Listings.asp?Standard=003&Company=24250&


NSF/ANSI 3
Commercial Warewashing Equipment

Racks per Hour / Dishes per Hour / Water Consumption Calculations

For informational purposes, the estimated racks per hour or dishes per hour for NSF/ANSI 3 Certified dishwashers can be calculated as follows:

Racks per Hour for Stationary Rack Dishwashers = 3600(NR) / TC

Racks per Hour for Rack Conveyor Dishwashers = (CS)(60) / RL

Dishes per Hour for Rackless Conveyor Dishwashers = (120)(CS)(CW) / PD

Water Consumption (gallons per hour) for Stationary Rack Dishwashers = (GPC)(RPH)

Water Consumption (gallons per hour) for Conveyor Dishwashers = (GPM)(60)

Where: CS = Conveyor speed measured in feet per minute
              CW = Conveyor width measured in inches
              GPC = Gallons per cycle
              GPM = Gallons per minute
              NR = Number of racks the dishwasher is designed to hold per cycle
              PD = Distance between pegs measured in inches, center to center of the peg, in the direction of conveyor travel
              RL = Length of the rack measured in feet
              RPH = Racks per hour
              TC = Total cycle time measured in seconds

The total cycle time includes wash, rinse, dwell, and load times. Load times will vary depending on the type of dishwasher. Estimated load times commonly used for specific types of dishwashers are as follows:
door type (straight thru) - 5 seconds
door type (corner) - 7 seconds
hood type - 8 seconds
front opening type - 30 seconds



 
Jackson WWS, Inc. 
6209 North US Highway 25 East
Gray, KY 40734 
United States 
888-800-JMSC 
606-523-9795
Visit this company's website

Facility : Barbourville, KY


CONVEYOR DISHWASHING MACHINES
      Final Rinse    
      (20 psi) Conveyor Speed  
  Model Conveyor Flow Usage (Max.) Footnotes
  Number Width gpm gph (ft/min.)  

Multiple Tank Rack Conveyor - Hot Water Sanitizing
  AJ-100 20x20  3.7   222   8   [1] [2] [13]
  AJ-64 20x20  3.7   222   8   [1] [13]
  AJ-86 20x20  3.7   222   8   [1] [2] [13]
 
[1] Model designation may have suffix CE for electrically heated, CS for steam heated, or
    CGP for gas heated.  Gas heated machines have a single-source gas booster which also
    maintains the appropriate wash tank temperature.
[2] With recirculated prewash.  Prewash temperature 110° - 140°F is obtained from wash tank
    overflow and fresh water supply.
[13] Unit may be equipped with modular heat recovery/vapor removal system that is connected
     on both the load and unload ends of the unit.  Modules may use existing installation
     ventilation system to move vapor or may be equipped with ventilation fans to move air as
     required.

Multiple Tank Rackless Conveyor - Hot Water Sanitizing
  JFT 29  2.3   139.2   8.6   [3]
  JFT-G 29  2.3   139.2   8.6   [3]
  JFT-S 29  2.3   139.2   8.6   [3]
  JFTL 29.5  .97   58.1   6.66   [3]
 
[3] The peg spacing for the JFT series rackless conveyor dishmachines is 2".

Single Tank Rack Conveyor - Hot Water Sanitizing [13]
  AJ-44 20x20  3.9   234   6.9   [4]
  AJ-44 20x20  2.4   144   5.7   [5] [6]
  AJ-54 20x20  4.6   279   7.5   [1]
  AJ-66 20x20  3.9   234   6.9   [1] [2] [4]
  AJ-66 20x20  2.4   144   5.7   [5] [6]
  AJ-76 20x20  4.6   279   7.5   [1] [2]
  AJ-80 20x20  3.9   234   6.9   [1] [2] [4]
  AJ-80 20x20  2.4   144   5.7   [5] [6]
  AJ-90 20x20  4.6   279   7.5   [1] [2]
  AJX-44 20x20  2.6   154.3   6.2   [4] [7] [8]
  AJX-54 20x20  2.6   154.3   6.3   [4] [7] [8]
  AJX-66 20x20  2.6   154.3   6.2   [2] [4] [7] [8]
  AJX-76 20x20  2.6   154.3   6.2   [2] [4] [7] [8]
  AJX-80 20x20  2.6   154.3   6.2   [2] [4] [7] [8]
  AJX-90 20x20  2.6   154.3   6.2   [2] [4] [7] [8]
  RackStar 44 20x20  1.16   69.8   6.41   [9]
  RackStar 44 20x20  1.95   117   6.41   [12]
  RackStar 44S 20x20  1.16   69.8   6.41   [9]
  RackStar 44S 20x20  1.95   117   6.41   [12]
  RackStar 66 20x20  1.18   70.74   6.1   [9]
  RackStar 66 20x20  2.54   152.4   6.1   [12]
  RackStar 66S 20x20  1.18   70.74   6.1   [9]
  RackStar 66S 20x20  2.54   152.4   6.1   [12]
  WareForce 44H 20x20  2.6   154.3   6.2   [4] [7]
  WareForce 66H 20x20  2.6   154.3   6.2   [2] [4] [7]
  WareForce RS44 20x20  1.16   69.8   6.41   [9]
  WareForce RS44 20x20  1.95   117   6.41   [12]
  WareForce RS44S 20x20  1.16   69.8   6.41   [9]
  WareForce RS44S 20x20  1.95   117   6.41   [12]
  WareForce RS66 20x20  1.18   70.74   6.1   [9]
  WareForce RS66 20x20  2.54   152.4   6.1   [12]
  WareForce RS66S 20x20  1.18   70.74   6.1   [9]
  WareForce RS66S 20x20  2.54   152.4   6.1   [12]
 
[1] Model designation may have suffix CE for electrically heated, CS for steam heated, or
    CGP for gas heated.  Gas heated machines have a single-source gas booster which also
    maintains the appropriate wash tank temperature.
[2] With recirculated prewash.  Prewash temperature 110° - 140°F is obtained from wash tank
    overflow and fresh water supply.
[4] Units produced after February 15, 2007 may be dual temperature convertible models.
[5] Model designation may have suffix E for electrically heated, G for gas heated, or S for
    steam heated.
[6] Model designation may have suffix T to indicate Traditional series.
[7] Final rinse flow and usage are based on a 15 PSI flow pressure.
[8] Model designation may have suffix CE for electrically heated, CG for gas heated, or S
    for steam heated.
[9] Model designation may have suffix S for steam heated and/or suffix C for a CREW style
    rack conveyor machine.
[12] Units may come equipped with additional rinse arms for use in "Turbo" rinse mode, which
     results greater water consumption.  This is not a post sanitizing rinse.
[13] Unit may be equipped with modular heat recovery/vapor removal system that is connected
     on both the load and unload ends of the unit.  Modules may use existing installation
     ventilation system to move vapor or may be equipped with ventilation fans to move air as
     required.

COMPONENTS:

Single Tank Rack Conveyor - Chemical Sanitizing [13]
  AJ-44 20x20  3.9   234   6.5   [4] [10] [11]
  AJ-66 20x20  3.9   234   6.5   [2] [4] [10] [11]
  AJ-80 20x20  3.9   234   6.9   [2] [4] [10] [11]
  AJX-44 20x20  2.7   164.4   5.8   [4] [7] [8] [11]
  AJX-54 20x20  2.6   154.3   6.2   [4] [7] [8]
  AJX-66 20x20  2.7   164.4   5.8   [2] [7] [8] [11]
  AJX-76 20x20  2.6   154.3   6.2   [2] [4] [7] [8] [11]
  AJX-80 20x20  2.7   164.4   5.8   [2] [4] [7] [8] [11]
  AJX-90 20x20  2.6   154.3   6.2   [2] [4] [7] [8] [11]
  RackStar 44 20x20  1.16   69.8   6.41   [9]
  RackStar 44 20x20  1.95   117   6.41   [12]
  RackStar 44S 20x20  1.16   69.8   6.41   [9]
  RackStar 44S 20x20  1.95   117   6.41   [12]
  RackStar 66 20x20  2.54   152.4   6.1   [12]
  RackStar 66 20x20  1.18   70.74   6.1   [9]
  RackStar 66S 20x20  1.18   70.74   6.1   [9]
  RackStar 66S 20x20  2.54   152.4   6.1   [12]
  WareForce 44L 20x20  2.7   164.4   5.8   [4] [11]
  WareForce 66L 20x20  2.7   164.4   5.8   [2] [4] [7] [11]
  WareForce RS44 20x20  1.16   69.8   6.41   [9]
  WareForce RS44 20x20  1.95   117   6.41   [12]
  WareForce RS44S 20x20  1.16   69.8   6.41   [9]
  WareForce RS44S 20x20  1.95   117   6.41   [12]
  WareForce RS66 20x20  1.18   70.74   6.1   [9]
  WareForce RS66 20x20  2.54   152.4   6.1   [12]
  WareForce RS66S 20x20  2.54   152.4   6.1   [12]
  WareForce RS66S 20x20  1.18   70.74   6.1   [9]
 
[2] With recirculated prewash.  Prewash temperature 110° - 140°F is obtained from wash tank
    overflow and fresh water supply.
[4] Units produced after February 15, 2007 may be dual temperature convertible models.
[7] Final rinse flow and usage are based on a 15 PSI flow pressure.
[8] Model designation may have suffix CE for electrically heated, CG for gas heated, or S
    for steam heated.
[9] Model designation may have suffix S for steam heated and/or suffix C for a CREW style
    rack conveyor machine.
[10] Model designation may have suffix CEL for electrically heated or CSL for steam heated.
[11] Nonrecirculated, fresh water, final rinse, 50 ppm available chlorine.
[12] Units may come equipped with additional rinse arms for use in "Turbo" rinse mode, which
     results greater water consumption.  This is not a post sanitizing rinse.
[13] Unit may be equipped with modular heat recovery/vapor removal system that is connected
     on both the load and unload ends of the unit.  Modules may use existing installation
     ventilation system to move vapor or may be equipped with ventilation fans to move air as
     required.


GLASSWASHING MACHINES

Chemical Sanitizing Conveyor Glasswasher
  Delta 115
  Delta 1200
  GW1200
  WareForce CG-115
  WareForce CG1200


STATIONARY RACK DISHWASHING MACHINES
      Final Rinse    
      (20 psi) Operating Time  
  Model Rack Size Flow Usage (seconds) Footnotes
  Number Width gpm gph Wash Rinse Dwell  

Single Tank Door - Chemical Sanitizing
  Conserver XL 20x20  N/A   40.2   42   25   20   [1] [2] [3]
  Conserver XL HH 20x20  N/A   62.8   43   25   18   
  Conserver XL-E 20x20  N/A   40.2   42   25   20   [1] [2] [3]
  Conserver XL-X 20x20  N/A   40.2   42   25   20   [1] [2] [3]
  Conserver XL2 2(20x20)  N/A   144   35   20   16   [2] [3] [4] [5] [6] [7] [8]
  Conserver XL2 2(20x20)  N/A   120   40   25   20   [2] [3] [4] [5] [6] [7] [8]
  Conserver XL2 2(20x20)  11.9   91.26   53   14   20   [3] [4] [5] [6] [7] [8] [9] [10]
  DLT1 20x20  N/A   40.2   42   25   20   [1] [2] [3]
  DLT2 2(20x20)  N/A   144   35   20   16   [2] [3] [4] [5] [6] [7] [8]
  DLT2 2(20x20)  11.9   91.26   53   14   20   [3] [4] [5] [6] [7] [8] [10]
  DLT2 2(20x20)  N/A   120   40   25   20   [2] [3] [4] [5] [6] [7] [8]
  DLT2C 2(20x20)  11.9   88.26   53   14   20   [3] [4] [5] [6] [7] [8] [10]
  Delta 5 20x20  N/A   36   46   25   21   
  Delta 5 20x20  N/A   36   43   24   18   
  Delta 5E 20x20  N/A   36   46   25   21   
  GW5 20x20  N/A   36   43   24   18   
  GW5 20x20  N/A   36   46   25   21   
  WareForce 1 HH 20x20  N/A   62.8   43   25   18   
  WareForce 1-E 20x20  N/A   40.2   42   25   20   [1] [2] [3]
  WareForce DG 20x20  N/A   36   43   24   18   
  WareForce I 20x20  N/A   40.2   42   25   20   [1] [2] [3]
  WareForce I-X 20x20  N/A   40.2   42   25   20   [1] [2] [3]
  WareForce II 2(20x20)  11.9   91.26   53   14   20   [3] [4] [5] [6] [7] [8] [10]
  WareForce II-C 2(20x20)  11.9   86.6   53   14   28   [4] [5] [6] [7] [8] [10]
 
[1] Recirculated pumped rinse, minimum 50 ppm available chlorine.
[2] Models may have ability for multiple cylcle times: 90 seconds, 2 minutes or 6 minutes.
[3] Model has the option of an available detergent dispenser.
[4] Accepted only with Jackson chemical feeders, peristaltic pump or pinch valve.
[5] Single tank machine utilizing two racks per complete operating cycle.
[6] Pumped rinse, minimum 50 ppm available chlorine, minimum 120°F.
[7] Unit equipped with a multiple setting time delay feature to extend wash times.  Maximum
    wash time time delays are 5 minutes.
[8] Suffix CML or CMR may appear. CML indicates corner machine left. CMR indicates corner
    machine right.
[9] Model is available as a corner option with 88.26 gph.
[10] Dwell includes drain and fill cycles.

Single Tank Door - Hot Water Sanitizing
  DHT 20x20  4.1   51.6   40   13   4   [12] [13] [14]
  DHT-HH 20x20  5.46   72   45   15   2   [12] [13] [14] [15]
  TempStar 20x20  4.1   51.6   40   13   4   [12] [13] [14]
  TempStar HH 20x20  5.46   72   45   15   2   [12] [13] [14] [15]
  TempStar HH/S 20x20  5.46   72   45   11   2   [12] [13] [14] [15]
  UHT 20x20  6.6   26.4   82   10   28   
  WareForce HT-180 20x20  4.1   51.6   40   13   4   [12] [13] [14]
  WareForce HT-180DT 20x20  3.78   39.5   40   11   7   [12] [14] [16]
  WareForce HT-180DTN 20x20  3.78   39.5   40   11   7   [12] [14] [16] [17]
  WareForce HT-180DTS 20x20  3.78   39.5   40   11   7   [12] [14] [16] [18]
  WareForce HT-180HH 20x20  5.46   72   45   15   2   [12] [13] [14] [15]
 
[12] Non-recirculated fresh water final rinse.
[13] Model designation may have suffix /NB to indicate that the unit does not come with an
     integral booster and must be supplied with a minimum 180°F fresh water hook-up or GP or
     GPX to indicate gas heated model.  Gas heated machines have a single-source gas booster
     which maintains the appropriate wash tank temperature.  Models without a suffix come
     with an integral booster for a minimum 40°F rinse temperature rise.
[14] Unit may be equipped with optional condensate removal system.
[15] Unit equipped with a multiple setting time delay feature to extend wash times.  Maximum
     wash time delays are 5 minutes.
[16] Final rinse pressure of 8-12PSI	.
[17] Suffix N indicates unit not supplied with booster heater and must be supplied with 180°
     water supply.
[18] Steam heated model	.

Single Tank Hood - Hot Water Sanitizing
  10A 17xdia.  7.8   58   60   10   2   [23]
  10APRB 17xdia.  7.8   58   60   10   2   [24]
  10APRB-M 17xdia.  7.8   58   60   10   2   [24]
  10U 17xdia.  7.8   58   60   10   2   [23]
 
[23] Model designation may have suffix B to designate an integral booster for a minimum 40°F
     temperature rise.
[24] Model comes with an integral booster for a minimum 40°F temperature rise.

COMPONENTS:

Single Tank Door - Chemical Sanitizing
  TempStar HH LT 20x20  N/A   62.7   44.6   13.6   58.2   [12] [13] [14] [15]
  TempStar LT 20x20  6.5   73   45   12   2   [25]
  ULT 20x20  6.6   28.8   56   35   26   [10]
  WareForce LT-120 20x20  N/A   62.7   44.6   13.6   58.2   [12] [13] [14] [15]
  WareForce UL30 20x20  6.6   28.8   56   35   26   [10]
 
[10] Dwell includes drain and fill cycles.
[12] Non-recirculated fresh water final rinse.
[13] Model designation may have suffix /NB to indicate that the unit does not come with an
     integral booster and must be supplied with a minimum 180°F fresh water hook-up or GP or
     GPX to indicate gas heated model.  Gas heated machines have a single-source gas booster
     which maintains the appropriate wash tank temperature.  Models without a suffix come
     with an integral booster for a minimum 40°F rinse temperature rise.
[14] Unit may be equipped with optional condensate removal system.
[15] Unit equipped with a multiple setting time delay feature to extend wash times.  Maximum
     wash time delays are 5 minutes.
[25] Non-recirculated fresh water final rinse.

[11] Model will always be supplied with sanitizer pump, however detergent and rinse aid
     feeders are optional.
[19] Extended Wash Cycle Option (262 seconds) available.
[20] Model may have detergent or rinse aid chemical feeder pump or both.
[21] Unit is supplied with integral booster for minimum 40°F rinse temperature rise.
[22] Non-steam-heated models without integral booster require 180°F minimum fresh water
     hook-up.

Number of matching Manufacturers is 1
Number of matching Products is 116
Processing time was 0 seconds