NSF Product and Service Listings

[1] (1) One number to identify rinsing concept: 1, 2, 3…
    (2) One character to localise body connection: S, V, U 
    (3) One character to identify connection sealing type: O, D, F
    (4) Three numbers to identify flow rate: 050, 060, 080, 110
    (5) One character and/or one number to identify connection material: 0, P3, X4
    (6) One character to describe connection type: E, R, D, G, T, F
    (7) 2 digits number to describe connection size: 18, 44, 66, 64, 88, 86 
    (8) Two character to identify sealing material and type: FF, PF, PZ
    (9) Up to 5 possible digits to describe electrical customization
    (10) Optional S (XXX) numbering of customer specific version.
[Pb] Product also evaluated and determined to possess weighted average lead content of
     <=0.25% and complies with lead content requirements for “lead free” plumbing as defined
     by California, Vermont, Maryland, and Louisiana state laws and the U.S. Safe Drinking
     Water Act.

[2] (1) 1-2 digits indicate a special version, e.g spring position
    (2) 2 digits indicate fitting type		
    (3) 1-4 digits indicate push-in connector size; multiple entries are not
        applicable for the same size		
    (4) Up to 8 digits indicate the thread size and type, stem connector, hosetail
        or bayonet; omitted if only push-in connection		
    (5) 3-4 digits indicate throttle		
    (6) 3 digits indicate opening pressure; not applicable at 0.1 bar 	
    (7) Up to 5 digits indicate the mesh size and material		
    (8) Sealing material:
        FF  - FPM
        FR  - FPM
        FT  - FPM
        PF  - EPDM
        QF  - VMQ
        QFF - FPM + VMQ
        QPF - EPDM + VMQ
        QFT - FPM + VMQ
        QPT - EPDM + VMQ
    (9) 2 digits indicate nominal diameter
    (10) Optional S (+1-2 digits) indicate a specific version		
[Pb] Product also evaluated and determined to possess weighted average lead content of
     <=0.25% and complies with lead content requirements for “lead free” plumbing as defined
     by California, Vermont, Maryland, and Louisiana state laws and the U.S. Safe Drinking
     Water Act.

[3] (1) optional 1 digit indicates special valve type
    (2) 1: push-on fitting; 9: push-in fitting
    (3) 2 digits indicate fitting type
    (4) 2 digits indicate nominal diameter, e.g. DN4 (40)
    (5) 1-4 digits indicate push-in/on connector size;	
        multiple entries are not applicable for the same size
    (6) Sealing material: FF, PF, PZ, QF, QFF, QPF, QPZ
    (7) optional up to 8 digits indicate connection size and type, e.g. thread, stem
    connector
    (8) 3 digits indicate opening pressure; not applicable at 0.1 bar
    (9) optional S(+1-2 digits) indicate a specific version
[Pb] Product also evaluated and determined to possess weighted average lead content of
     <=0.25% and complies with lead content requirements for “lead free” plumbing as defined
     by California, Vermont, Maryland, and Louisiana state laws and the U.S. Safe Drinking
     Water Act.

[4] (1) 2 digits indicating nominal diameter: DN0,5 (05) DN1 (10) DN1,5 (15) DN2 
        (20), DN2,5 (25) DN3 (30), DN3,5 (35) DN4 (40) DN4,5 (45) DN5 (50)
    (2) Digits indicating plug connection diameter, between 4 and 8 and 1/4"
    (3) O-ring material:
        FF  - FKM black
        FR  - FKM red
        PF  - HITEC EPDM
        PZ  - EPDM
        QF  - Silicone
        QFF - FKM black + silicone
        QFR - FKM red + silicone
        QPF - Hitec EPDM + silicone
        QPZ - EPDM + Silicone
    (4) Optional: S (X) numbering of customer specific version, where X ranges from 
        01 to 999
[5] For use in contact with coffee, tea and water only.
[Pb] Product also evaluated and determined to possess weighted average lead content of
     <=0.25% and complies with lead content requirements for “lead free” plumbing as defined
     by California, Vermont, Maryland, and Louisiana state laws and the U.S. Safe Drinking
     Water Act.

[6] (1) Up to 2 digits indicate series (1 - Push-On, 9 - Push-In, FL - sub-base)				
    (2)	2 digits indicate fitting type and optional sub-base type				
    (3)	Body Material P3, V				
    (4)	1-4 digits indicate stem connector, hose tail, push-in connector size; multiple 
        entries are not applicable for the same size				
    (5)	Sealing Material FF, FR, PF, PZ, QF				
    (6)	Optional 2 digits indicate cable length incl. supply connection or  S (+1-3 digits) 
        indicate a specific version				
    (7)	Up to 2 digits indicate variant vs. undefined digits for customer specific 
        variant				
    (A)	Up to 3 digits indicate sensor size and sleeve material				
    (B)	3-4 digits indicate measuring range start				
    (C)	3 digits indicate measuring range end				
    (D)	Up to 5 digits indicate output signal, e.g. U05/I				
    (E)	2 digits indicate supply voltage				
    (F)	3 digits indicate default or vacuum type incl. pressure nominal, e.g. V04				
    (G)	Sensor housing material X01, X04 – not applicable for ceramic housing				
    (H)	Sensor type, e.g. PT100 , NTC10, …				
    (I)	2-3 digits indicate type of motor, type of electronic and/or customer specific
    variant			
    (J)	2 digits indicate nominal diameter; e.g. DN0,5 (05) or DN5 (50)				
    (K)	Up to 5 digits indicate control signal	
[Pb] Product also evaluated and determined to possess weighted average lead content of
     <=0.25% and complies with lead content requirements for “lead free” plumbing as defined
     by California, Vermont, Maryland, and Louisiana state laws and the U.S. Safe Drinking
     Water Act.

[7] (1)  Optional 3 digits indicate fitting type			
    (2)  Optional 2-4 digits indicate the material: P3 (PPSU), P5 (PEEK), X4 (1.4404), X5
    (1.4305)			
    (3)  1-4 digits indicate push-in connector size; multiple entries are not applicable for
    the 
         same size			
    (4)  Optional 1-2 digits indicate the sealing material
         FF = FKM		
         PF = EPDM		
    	 QF = VMQ		
    (5)  Optional up to 8 digits indicate the thread size and type			
    (6)  Optional 1-3 digits indicate the thread material	 (stainless steel)		
    (7)  2-3 digits indicate the sensor material (stainless steel)			
    (8)  2-8 digits indicate the type of sensor 			
    (9)  2-6 digits indicate the sleeve length			
    (10) 2-4 digits indicate the cable length			
    (11) Optional S (+1-3 digits) indicate a specific version
[Pb] Product also evaluated and determined to possess weighted average lead content of
     <=0.25% and complies with lead content requirements for “lead free” plumbing as defined
     by California, Vermont, Maryland, and Louisiana state laws and the U.S. Safe Drinking
     Water Act.

[6] (1) Up to 2 digits indicate series (1 - Push-On, 9 - Push-In, FL - sub-base)				
    (2)	2 digits indicate fitting type and optional sub-base type				
    (3)	Body Material P3, V				
    (4)	1-4 digits indicate stem connector, hose tail, push-in connector size; multiple 
        entries are not applicable for the same size				
    (5)	Sealing Material FF, FR, PF, PZ, QF				
    (6)	Optional 2 digits indicate cable length incl. supply connection or  S (+1-3 digits) 
        indicate a specific version				
    (7)	Up to 2 digits indicate variant vs. undefined digits for customer specific 
        variant				
    (A)	Up to 3 digits indicate sensor size and sleeve material				
    (B)	3-4 digits indicate measuring range start				
    (C)	3 digits indicate measuring range end				
    (D)	Up to 5 digits indicate output signal, e.g. U05/I				
    (E)	2 digits indicate supply voltage				
    (F)	3 digits indicate default or vacuum type incl. pressure nominal, e.g. V04				
    (G)	Sensor housing material X01, X04 – not applicable for ceramic housing				
    (H)	Sensor type, e.g. PT100 , NTC10, …				
    (I)	2-3 digits indicate type of motor, type of electronic and/or customer specific
    variant			
    (J)	2 digits indicate nominal diameter; e.g. DN0,5 (05) or DN5 (50)				
    (K)	Up to 5 digits indicate control signal	
[Pb] Product also evaluated and determined to possess weighted average lead content of
     <=0.25% and complies with lead content requirements for “lead free” plumbing as defined
     by California, Vermont, Maryland, and Louisiana state laws and the U.S. Safe Drinking
     Water Act.

[6] (1) Up to 2 digits indicate series (1 - Push-On, 9 - Push-In, FL - sub-base)				
    (2)	2 digits indicate fitting type and optional sub-base type				
    (3)	Body Material P3, V				
    (4)	1-4 digits indicate stem connector, hose tail, push-in connector size; multiple 
        entries are not applicable for the same size				
    (5)	Sealing Material FF, FR, PF, PZ, QF				
    (6)	Optional 2 digits indicate cable length incl. supply connection or  S (+1-3 digits) 
        indicate a specific version				
    (7)	Up to 2 digits indicate variant vs. undefined digits for customer specific 
        variant				
    (A)	Up to 3 digits indicate sensor size and sleeve material				
    (B)	3-4 digits indicate measuring range start				
    (C)	3 digits indicate measuring range end				
    (D)	Up to 5 digits indicate output signal, e.g. U05/I				
    (E)	2 digits indicate supply voltage				
    (F)	3 digits indicate default or vacuum type incl. pressure nominal, e.g. V04				
    (G)	Sensor housing material X01, X04 – not applicable for ceramic housing				
    (H)	Sensor type, e.g. PT100 , NTC10, …				
    (I)	2-3 digits indicate type of motor, type of electronic and/or customer specific
    variant			
    (J)	2 digits indicate nominal diameter; e.g. DN0,5 (05) or DN5 (50)				
    (K)	Up to 5 digits indicate control signal	
[Pb] Product also evaluated and determined to possess weighted average lead content of
     <=0.25% and complies with lead content requirements for “lead free” plumbing as defined
     by California, Vermont, Maryland, and Louisiana state laws and the U.S. Safe Drinking
     Water Act.

[6] (1) Up to 2 digits indicate series (1 - Push-On, 9 - Push-In, FL - sub-base)				
    (2)	2 digits indicate fitting type and optional sub-base type				
    (3)	Body Material P3, V				
    (4)	1-4 digits indicate stem connector, hose tail, push-in connector size; multiple 
        entries are not applicable for the same size				
    (5)	Sealing Material FF, FR, PF, PZ, QF				
    (6)	Optional 2 digits indicate cable length incl. supply connection or  S (+1-3 digits) 
        indicate a specific version				
    (7)	Up to 2 digits indicate variant vs. undefined digits for customer specific 
        variant				
    (A)	Up to 3 digits indicate sensor size and sleeve material				
    (B)	3-4 digits indicate measuring range start				
    (C)	3 digits indicate measuring range end				
    (D)	Up to 5 digits indicate output signal, e.g. U05/I				
    (E)	2 digits indicate supply voltage				
    (F)	3 digits indicate default or vacuum type incl. pressure nominal, e.g. V04				
    (G)	Sensor housing material X01, X04 – not applicable for ceramic housing				
    (H)	Sensor type, e.g. PT100 , NTC10, …				
    (I)	2-3 digits indicate type of motor, type of electronic and/or customer specific
    variant			
    (J)	2 digits indicate nominal diameter; e.g. DN0,5 (05) or DN5 (50)				
    (K)	Up to 5 digits indicate control signal	
[Pb] Product also evaluated and determined to possess weighted average lead content of
     <=0.25% and complies with lead content requirements for “lead free” plumbing as defined
     by California, Vermont, Maryland, and Louisiana state laws and the U.S. Safe Drinking
     Water Act.

[8] (1)  1-4 digits indicate stem connector, hose tail or push-in connector size; 
         multiple entries are not applicable for the same size
    (2)  Up to 8 digits indicate the thread size and type
    (3)  3-7 digits indicate Rapid connection
    (A)  Optional sealing material: FF, FT = FPM; PF = EPDM; QF = VMQ
    (B)  Body: X4, X44, X4M, X44M = 1.4404; X5, X54= 1.5305
    (C)  1-2 digits indicate release button material
    (D)  Release button colour
    (M)  Appendix in case of union nut made of brass (no food contact)
    S(X) Optional: indicates customer specific version
[Pb] Product also evaluated and determined to possess weighted average lead content of
     <=0.25% and complies with lead content requirements for “lead free” plumbing as defined
     by California, Vermont, Maryland, and Louisiana state laws and the U.S. Safe Drinking
     Water Act.

[9] (1) 1-3 digits indicate stem connector, hose tail or push-in connector size; multiple
    entries are not applicable for the same size
    (2) Up to 10 digits indicate the thread size, type and material
    (3) Sealing material:  FT - FKM, PT - EPDM
    (4) Optional: S followed by digits/numbers, indicates customer specific version
[Pb] Product also evaluated and determined to possess weighted average lead content of
     <=0.25% and complies with lead content requirements for “lead free” plumbing as defined
     by California, Vermont, Maryland, and Louisiana state laws and the U.S. Safe Drinking
     Water Act.

[10] (1) 1-4 digits indicate stem connector, hose tail, push-in connector size or number of
     inlets/outlets
     (2) Sealing material: FF, FR, FT, PF, PT, PZ, QF
     (3) Up to 8 digits indicate the thread size and type
     (4) Optional S (+1-3 digits) indicate a specific version
     (5) 1 digit indicate connection type
     (6) optional 1 digit indicate installation type
[10] (1) 1-4 digits indicate stem connector, hose tail, push-in connector size or number of
     inlets/outlets
     (2) Sealing material: FF, FR, FT, PF, PT, PZ, QF
     (3) Up to 8 digits indicate the thread size and type
     (4) Optional S (+1-3 digits) indicate a specific version
     (5) 1 digit indicate connection type
     (6) optional 1 digit indicate installation type
[Pb] Product also evaluated and determined to possess weighted average lead content of
     <=0.25% and complies with lead content requirements for “lead free” plumbing as defined
     by California, Vermont, Maryland, and Louisiana state laws and the U.S. Safe Drinking
     Water Act.

[11] (1)1-3 digits indicate stem connector, hose tail or push-in connector size multiple
     entries are not applicable for the same size
     (2) Up to 8 digits indicate the thread size and type
     (3) Sealing material: FF, FR, PF, PZ, QF
     (4) Optional S (+1-3 digits) indicate a specific version
[Pb] Product also evaluated and determined to possess weighted average lead content of
     <=0.25% and complies with lead content requirements for “lead free” plumbing as defined
     by California, Vermont, Maryland, and Louisiana state laws and the U.S. Safe Drinking
     Water Act.

[12] (1)  1-4 digits indicate stem connector, hose tail or push-in connector size; 
          multiple entries are not applicable for the same size		
     (2)  Up to 8 digits indicate the thread size and type		
     (3)  3-7 digits indicate Rapid connection
     (A)  Optional sealing material  
          FF, FT - FPM	
          PF - EPDM	
          QF - VMQ	
     (B)  Body - X4, X44, X4M, X44M - 1.4404;  X5, X54 - 1.4305
     (C)  1-2 digits indicate release button material
     (D)  Release button colour
     (M)  Appendix in case of union nut made of brass (no food contact)
     S(X) Optional - Indicates customer specific version
[Pb] Product also evaluated and determined to possess weighted average lead content of
     <=0.25% and complies with lead content requirements for “lead free” plumbing as defined
     by California, Vermont, Maryland, and Louisiana state laws and the U.S. Safe Drinking
     Water Act.

[13] (1) 3 digits indicate the series and version.
     (2) Optional 2-4 digits indicate the material: X4, X4M, X44M = 1.4404; X5 = 1.4305; P3 =
     
         PPSU.
     (3) 1 digit indicates the function.
     (4) 2 digits indicate the nominal diameter.
     (5) 1-3 digits indicate the connection; multiple entries are not applicable for the same
     
         size.  All connections are certified.
     (6) 2 digits indicate the sealing material: PF = EPDM; FF = FPM. 
     (7) Optional 1 digit indicates the hexagonal plunger.
     (8) Optional S (+1-2 digits) indicate a specific version that does not impact 
         certification.
     (9) Optional 4-5 digits indicate the voltage and current.
     (10) 2-3 digits indicate the solenoid coil; 00 = partial solenoid valve without solenoid
     
          coil.
     (11)	2-3 digits indicate a specific version that does not impact certification.
     (12)	Optional / + 1-2 digits indicate a battery version.
     (13) digit 1-99 indicates specific version that does not impact certification
[14] Only acceptable for use in contact with non-carbonated, potable water under constant
     service pressure.
[16] For use in contact with coffee, tea and water only.
[Pb] Product also evaluated and determined to possess weighted average lead content of
     <=0.25% and complies with lead content requirements for “lead free” plumbing as defined
     by California, Vermont, Maryland, and Louisiana state laws and the U.S. Safe Drinking
     Water Act.

[15] (1)	3 digits indicate the series and version
     (2)	1 digit indicates the function
     (3)	2 digits indicate the nominal diameter
     (4)	1-3 digits indicate the connection type and size or flange version; multiple 
         entries are not applicable for the same size
     (5)	2 digits indicate the sealing material
     (6)	5-6 digits indicate the voltage and current
     (7)	2 digits indicate the solenoid coil
     (8)	2-3 digits indicate a specific version
     (9)	Optional 4-5 digits indicate a battery version
[Pb] Product also evaluated and determined to possess weighted average lead content of
     <=0.25% and complies with lead content requirements for “lead free” plumbing as defined
     by California, Vermont, Maryland, and Louisiana state laws and the U.S. Safe Drinking
     Water Act.

[17] (1) 1-2 digits indicate version
     (2) 1-2 digits indicate calibrated medium
     (3) 1-3 digits indicate connection size
     (4) 2 digits indicate sealing material: FF, FT - FPM; PF, PT, PZ - EPDM; QF - VMQ
     (5) 1-4 digits indicate start of measuring range
     (6) 1-5 digits indicate end of measuring range
     (7) 3-5 digits indicate analog output signal analog / digital
     (8) 1-5 digits indicate digital output signal analog / digital
     (9) Optional S (+ 1-3 digits) indicate a specific version
[Pb] Product also evaluated and determined to possess weighted average lead content of
     <=0.25% and complies with lead content requirements for “lead free” plumbing as defined
     by California, Vermont, Maryland, and Louisiana state laws and the U.S. Safe Drinking
     Water Act.