NSF Product and Service Listings
These NSF Official Listings are current as of Monday, September 23, 2019 at 12:15 a.m. Eastern Time. Please contact NSF to confirm the status of any Listing, report errors, or make suggestions.
Alert: NSF is concerned about fraudulent downloading and manipulation of website text. Always confirm this information by clicking on the below link for the most accurate information: http://info.nsf.org/Certified/PwsChemicals/Listings.asp?Company=0V430&Standard=060&
NSF/ANSI/CAN 60
Drinking Water Treatment Chemicals - Health Effects
Drinking Water Treatment Chemicals - Health Effects
| Brenntag Pacific, Inc. | |
| 10747 Patterson Place | |
| Santa Fe Springs, CA 90670 | |
| United States | |
| 323-562-9500 | |
| Visit this company's website |
Facility : Chandler, AZ
|
Citric Acid |
||
| Trade Designation | Product Function | Max Use |
| Citric Acid 50%[1] [2] | Membrane Cleaner | NA |
| Citric Acid 50% | pH Adjustment | 250mg/L |
| Citric Acid Solution[1] [2] | Membrane Cleaner | NA |
| Citric Acid Solution | pH Adjustment | 250mg/L |
[1] This product is designed to be used off-line and flushed out prior to using the system
for drinking water, following manufacturer's use instructions.
[2] The pH of the influent and effluent water should be monitored to ensure that all traces
of the product have been removed before placing into service.
|
||
|
Ferric Chloride |
||
| Trade Designation | Product Function | Max Use |
| Ferric Chloride 37-42% | Coagulation & Flocculation | 250mg/L |
| Ferric Chloride Solution | Coagulation & Flocculation | 250mg/L |
|
Hydrochloric Acid |
||
| Trade Designation | Product Function | Max Use |
| Hydrochloric Acid 15% | Corrosion & Scale Control pH Adjustment |
80mg/L |
| Hydrochloric Acid 20 Be | Corrosion & Scale Control pH Adjustment |
40mg/L |
| Hydrochloric Acid 22 Be | Corrosion & Scale Control pH Adjustment |
40mg/L |
| Muriatic Acid | Corrosion & Scale Control pH Adjustment |
40mg/L |
|
Miscellaneous Water Supply Products[1] [3] |
||
| Trade Designation | Product Function | Max Use |
| Innova | Well Cleaning Aid | NA |
| Innova 1.0 | Well Cleaning Aid | NA |
| Innova 1.5 | Well Cleaning Aid | NA |
[1] This product is designed to be used off-line and flushed out prior to using the system
for drinking water, following manufacturer's use instructions.
[3] The well is to be properly flushed and drained before being placed in service.
|
||
|
Sodium Bisulfite[4] |
||
| Trade Designation | Product Function | Max Use |
| Sodium Bisulfite 25% | Dechlorinator & Antioxidant | 69mg/L |
| Sodium Bisulfite 40% | Dechlorinator & Antioxidant | 46mg/L |
[4] This product contains sulfite. Sulfites have been known to cause potentially lethal
allergic reactions in sulfite-sensitive individuals. The maximum recommended allowable
residual sulfite level in the finished drinking water is 100 ppb (0.1 mg/L).
|
||
|
Sodium Chlorite[5] [CL] |
||
| Trade Designation | Product Function | Max Use |
| Sodium Chlorite 25% | Disinfection & Oxidation | 28mg/L |
[5] These products are certified for use in chlorine dioxide generation.
[CL] The residual levels of chlorine (hypochlorite ion and hypochlorous acid), chlorine
dioxide, chlorate ion, chloramine and disinfection by-products shall be monitored in the
finished drinking water to ensure compliance to all applicable regulations.
|
||
|
Sodium Hydroxide |
||
| Trade Designation | Product Function | Max Use |
| Sodium Hydroxide 25% | Corrosion & Scale Control pH Adjustment |
200mg/L |
| Sodium Hydroxide 33% | Corrosion & Scale Control pH Adjustment |
152mg/L |
| Sodium Hydroxide 50% | Corrosion & Scale Control pH Adjustment |
100mg/L |
|
Sulfuric Acid |
||
| Trade Designation | Product Function | Max Use |
| Sulfuric Acid 66BE | pH Adjustment | 50mg/L |
| Sulfuric Acid 93% | pH Adjustment | 50mg/L |
| Sulfuric Acid 98% | pH Adjustment | 50mg/L |
NOTE: Only products bearing the NSF Mark on the product, product packaging, and/or
documentation shipped with the product are Certified.
Facility : Chula Vista, CA
|
Sodium Hypochlorite[CL] |
||
| Trade Designation | Product Function | Max Use |
| 12.5% Sodium Hypochlorite | Algicide Disinfection & Oxidation |
84mg/L |
| Bleach 12.5% | Algicide Disinfection & Oxidation |
84mg/L |
| L A Chemclor | Algicide Disinfection & Oxidation |
84mg/L |
| LA Chemchlor | Algicide Disinfection & Oxidation |
84mg/L |
| Sodium Hypochlorite 12.5% | Algicide Disinfection & Oxidation |
84mg/L |
[CL] The residual levels of chlorine (hypochlorite ion and hypochlorous acid), chlorine
dioxide, chlorate ion, chloramine and disinfection by-products shall be monitored in the
finished drinking water to ensure compliance to all applicable regulations.
|
||
NOTE: Only products bearing the NSF Mark on the product, product packaging, and/or
documentation shipped with the product are Certified.
Facility : Fresno, CA
|
Calcium Chloride |
||
| Trade Designation | Product Function | Max Use |
| Calcium chloride solution | Softener Defluoridation |
200mg/L |
|
Citric Acid |
||
| Trade Designation | Product Function | Max Use |
| Citric Acid[1] [2] | Membrane Cleaner | NA |
| Citric Acid | pH Adjustment | 250mg/L |
| Citric Acid Solution | pH Adjustment | 250mg/L |
| Citric Acid Solution[1] [2] | Membrane Cleaner | NA |
[1] These products are designed to be used off-line and flushed out prior to using the
system for drinking water, following manufacturer's use instructions.
[2] The pH of the influent and effluent water shuold be monitored to ensure that all traces
of the product have been removed before placing into service.
|
||
|
Ferric Chloride |
||
| Trade Designation | Product Function | Max Use |
| Ferric Chloride Solution | Coagulation & Flocculation | 250mg/L |
|
Hydrochloric Acid |
||
| Trade Designation | Product Function | Max Use |
| Hydrochloric Acid 15% | Corrosion & Scale Control pH Adjustment |
80mg/L |
| Hydrochloric Acid 18% | Corrosion & Scale Control pH Adjustment |
70mg/L |
| Hydrochloric Acid 20% | Corrosion & Scale Control pH Adjustment |
63mg/L |
| Hydrochloric Acid 20BE | Corrosion & Scale Control pH Adjustment |
40mg/L |
| Hydrochloric Acid 22BE | Corrosion & Scale Control pH Adjustment |
40mg/L |
| Muriatic Acid 15% | Corrosion & Scale Control pH Adjustment |
80mg/L |
| Muriatic Acid 18% | Corrosion & Scale Control pH Adjustment |
70mg/L |
| Muriatic Acid 20% | Corrosion & Scale Control pH Adjustment |
63mg/L |
|
Phosphoric Acid |
||
| Trade Designation | Product Function | Max Use |
| Phosphoric Acid 75 | Corrosion & Scale Control | 13mg/L |
| Phosphoric Acid 75 Brennphos 75 | Corrosion & Scale Control | 13mg/L |
|
Sodium Bisulfite[3] |
||
| Trade Designation | Product Function | Max Use |
| Anti Chlor 30 | Antioxidant | 61mg/L |
| Sodium Bisulfite 25% | Antioxidant | 38mg/L |
| Sodium Bisulfite 30% | Antioxidant | 61mg/L |
| Sodium Bisulfite 38% | Antioxidant | 38mg/L |
| Sodium Bisulfite 40% | Antioxidant | 38mg/L |
[3] This product contains sulfite. Sulfites have been known to cause potentially lethal
allergic reactions in sulfite-sensitive individuals. The maximum recommended allowable
residual sulfite level in the finished drinking water is 100 ppb (0.1 mg/L).
|
||
|
Sodium Hydroxide |
||
| Trade Designation | Product Function | Max Use |
| Caustic Soda Solution, 25% | Corrosion & Scale Control pH Adjustment |
200mg/L |
| Caustic Soda Solution, 30% | Corrosion & Scale Control pH Adjustment |
165mg/L |
| Caustic Soda Solution, 50% | Corrosion & Scale Control pH Adjustment |
100mg/L |
| Sodium Hydroxide 20% | Corrosion & Scale Control pH Adjustment |
250mg/L |
| Sodium Hydroxide Solution, 25% | Corrosion & Scale Control pH Adjustment |
200mg/L |
| Sodium Hydroxide Solution, 30% | Corrosion & Scale Control pH Adjustment |
165mg/L |
| Sodium Hydroxide Solution, 50% | Corrosion & Scale Control pH Adjustment |
100mg/L |
| Sodium Hydroxide, 25% | Corrosion & Scale Control pH Adjustment |
200mg/L |
| Sodium Hydroxide, 30% | Corrosion & Scale Control pH Adjustment |
165mg/L |
| Sodium Hydroxide, 50% | Corrosion & Scale Control pH Adjustment |
100mg/L |
|
Sodium Hypochlorite[CL] |
||
| Trade Designation | Product Function | Max Use |
| Bleach 12.5% | Disinfection & Oxidation | 61mg/L |
| ECOLAB XY-12 | Disinfection & Oxidation | 103mg/L |
| L.A. Chemchlor 12.5% | Disinfection & Oxidation | 61mg/L |
| Sodium Hypochlorite | Disinfection & Oxidation | 61mg/L |
| Sodium Hypochlorite 12.5% | Disinfection & Oxidation | 61mg/L |
[CL] The residual levels of chlorine (hypochlorite ion and hypochlorous acid), chlorine
dioxide, chlorate ion, chloramine and disinfection by-products shall be monitored in the
finished drinking water to ensure compliance to all applicable regulations.
|
||
|
Sulfuric Acid |
||
| Trade Designation | Product Function | Max Use |
| Sulfuric Acid 25% | Corrosion & Scale Control pH Adjustment |
185mg/L |
| Sulfuric Acid 36% | pH Adjustment Corrosion & Scale Control |
129mg/L |
| Sulfuric Acid 50% | Corrosion & Scale Control pH Adjustment |
93mg/L |
| Sulfuric Acid 66BE | pH Adjustment Corrosion & Scale Control |
50mg/L |
| Sulfuric Acid 93% | Corrosion & Scale Control pH Adjustment |
50mg/L |
| Sulfuric Acid 98% | Corrosion & Scale Control pH Adjustment |
50mg/L |
NOTE: Only products bearing the NSF Mark on the product, product packaging, and/or
documentation shipped with the product are Certified.
Facility : Imperial, CA
|
Sodium Hypochlorite[CL] |
||
| Trade Designation | Product Function | Max Use |
| Sodium Hypochlorite 12.5% | Algicide Disinfection & Oxidation |
84mg/L |
[CL] The residual levels of chlorine (hypochlorite ion and hypochlorous acid), chlorine
dioxide, chlorate ion, chloramine and disinfection by-products shall be monitored in the
finished drinking water to ensure compliance to all applicable regulations.
|
||
NOTE: Only products bearing the NSF Mark on the product, product packaging, and/or
documentation shipped with the product are Certified.
Facility : Richmond, CA
|
Aluminum Sulfate[AL] |
||
| Trade Designation | Product Function | Max Use |
| Aluminum Sulfate | Coagulation & Flocculation | 150mg/L |
[AL] Based on an evaluation of health effects data, the level of aluminum in the finished
drinking water shall not exceed 2 mg/L.
|
||
|
Ammonium Sulfate |
||
| Trade Designation | Product Function | Max Use |
| Ammonium Sulfate 40% | Chloramination | 60mg/L |
| Ammonium Sulfate Solution | Chloramination | 60mg/L |
| AquaLAS 40% | Chloramination | 60mg/L |
| Liquid Ammonium Sulfate | Chloramination | 60mg/L |
|
Blended Phosphates |
||
| Trade Designation | Product Function | Max Use |
| AquaPure 3619 | Corrosion & Scale Control Sequestering |
25mg/L |
| AquaPure 3627 | Corrosion & Scale Control Sequestering |
25mg/L |
| AquaPure 3628 | Corrosion & Scale Control Sequestering |
25mg/L |
| AquaPure 3637 | Corrosion & Scale Control Sequestering |
25mg/L |
| AquaPure 3646 | Corrosion & Scale Control Sequestering |
25mg/L |
| AquaPure 3655 | Corrosion & Scale Control Sequestering |
25mg/L |
| AquaPure 3664 | Corrosion & Scale Control Sequestering |
25mg/L |
| AquaPure 3672 | Corrosion & Scale Control Sequestering |
25mg/L |
| AquaPure 3673 | Corrosion & Scale Control Sequestering |
25mg/L |
| AquaPure 3682 | Corrosion & Scale Control Sequestering |
25mg/L |
| AquaPure 3691 | Corrosion & Scale Control Sequestering |
25mg/L |
|
Citric Acid |
||
| Trade Designation | Product Function | Max Use |
| Citric Acid 50% | pH Adjustment | 250mg/L |
| Citric Acid 50%[1] [2] | Membrane Cleaner | NA |
| Citric Acid Solution | pH Adjustment | 250mg/L |
| Citric Acid Solution[1] [2] | Membrane Cleaner | NA |
[1] This product is designed to be used off-line and flushed prior to using the system for
drinking water, following manufacturer's use instructions.
[2] The pH of the influent and effluent water should be monitored to ensure that all traces
of the product have been removed before placing into service.
|
||
|
Ferric Chloride |
||
| Trade Designation | Product Function | Max Use |
| Ferric Chloride | Coagulation & Flocculation | 250mg/L |
| Ferric Chloride Liquid | Coagulation & Flocculation | 250mg/L |
| Ferric Chloride Solution | Coagulation & Flocculation | 250mg/L |
|
Hydrochloric Acid |
||
| Trade Designation | Product Function | Max Use |
| Hydrochloric Acid 15% | Corrosion & Scale Control pH Adjustment |
80mg/L |
| Hydrochloric Acid 18% | Corrosion & Scale Control pH Adjustment |
70mg/L |
| Hydrochloric Acid 20% | Corrosion & Scale Control pH Adjustment |
63mg/L |
| Hydrochloric Acid 20BE | Corrosion & Scale Control pH Adjustment |
40mg/L |
| Hydrochloric Acid 22BE | Corrosion & Scale Control pH Adjustment |
40mg/L |
| Muriatic Acid 15% | Corrosion & Scale Control pH Adjustment |
80mg/L |
| Muriatic Acid 18% | Corrosion & Scale Control pH Adjustment |
70mg/L |
| Muriatic Acid 20% | Corrosion & Scale Control pH Adjustment |
63mg/L |
|
Hydrofluosilicic Acid |
||
| Trade Designation | Product Function | Max Use |
| Fluosilicic Acid | Fluoridation | 6mg/L |
| HFS Acid | Fluoridation | 6mg/L |
| Hydrofluosilicic Acid | Fluoridation | 6mg/L |
|
Hydrogen Peroxide [HP] |
||
| Trade Designation | Product Function | Max Use |
| Hydrogen Peroxide, 10% | Oxidant | 80mg/L |
| Hydrogen Peroxide, 20% | Oxidant | 40mg/L |
| Hydrogen Peroxide, 25% | Oxidant | 32mg/L |
| Hydrogen Peroxide, 27.5%[3] | Oxidant | 29mg//L |
| Hydrogen Peroxide, 3% | Oxidant | 266mg/L |
| Hydrogen Peroxide, 30% | Oxidant | 26mg/L |
| Hydrogen Peroxide, 34% | Oxidant | 23mg/L |
| Hydrogen Peroxide, 35% | Oxidant | 23mg/L |
| Hydrogen Peroxide, 50% | Oxidant | 16mg/L |
| Hydrogen Peroxide, 7% | Oxidant | 114mg/L |
[3] This product may be used at a maximum use level of 100 mg/L for the following
functions:
- Reoxygenation of treated water
- Oxidation of organic residuals
- Oxidation of any reduced products, such as Fe(II) and sulfides
Treatment must be followed by chlorination to a chlorine residual no to exceed 4 mg/L,
the EPA's proposed maximum residual level.
[HP] Use of this product shall be followed by chlorination to remove levels of hydrogen
peroxide. Chlorine residuals shall not exceed 4 mg/L, the EPA's proposed maximum
residual level.
|
||
|
Monosodium Orthophosphate |
||
| Trade Designation | Product Function | Max Use |
| AquaPure 3601 | Corrosion & Scale Control Sequestering |
25mg/L |
|
Phosphoric Acid |
||
| Trade Designation | Product Function | Max Use |
| Aquapure Ortho | Corrosion & Scale Control | 26mg/L |
| Phosphoric Acid (36% PO4) | Corrosion & Scale Control | 26mg/L |
| Phosphoric Acid 75% | Corrosion & Scale Control | 13mg/L |
|
Polyamines[PY] |
||
| Trade Designation | Product Function | Max Use |
| 2719 Chemax | Coagulation & Flocculation | 20mg/L |
[PY] Polyamines Certified by NSF International comply with 40 CFR 141.111 requirements for
percent monomer and dose.
|
||
|
Sodium Bisulfite[4] |
||
| Trade Designation | Product Function | Max Use |
| Anti Chlor 30 | Antioxidant | 61mg/L |
| Sodium Bisulfite 25% | Antioxidant | 38mg/L |
| Sodium Bisulfite 30% | Antioxidant | 61mg/L |
| Sodium Bisulfite 38% | Antioxidant | 38mg/L |
| Sodium Bisulfite 40% | Antioxidant | 38mg/L |
[4] This product contains sulfite. Sulfites have been known to cause potentially lethal
allergic reactions in sulfite-sensitive individuals. The maximum recommended allowable
residual sulfite level in the finished drinking water is 100 ppb (0.1 mg/L).
|
||
|
Sodium Hydroxide |
||
| Trade Designation | Product Function | Max Use |
| Caustic Soda Solution, 50% | Corrosion & Scale Control pH Adjustment |
100mg/L |
| Sodium Hydroxide 20% | Corrosion & Scale Control pH Adjustment |
250mg/L |
| Sodium Hydroxide 25% | Corrosion & Scale Control pH Adjustment |
200mg/L |
| Sodium Hydroxide 30% | Corrosion & Scale Control pH Adjustment |
167mg/L |
| Sodium Hydroxide Solution, 50% | Corrosion & Scale Control pH Adjustment |
100mg/L |
| Sodium Hydroxide, 50% | Corrosion & Scale Control pH Adjustment |
100mg/L |
|
Sodium Hypochlorite[CL] |
||
| Trade Designation | Product Function | Max Use |
| Bleach 12.5% | Disinfection & Oxidation | 61mg/L |
| ECOLAB XY-12 | Disinfection & Oxidation | 103mg/L |
| L.A. Chemchlor 12.5% | Disinfection & Oxidation | 61mg/L |
| Sodium Hypochlorite | Disinfection & Oxidation | 61mg/L |
| Sodium Hypochlorite 12.5% | Disinfection & Oxidation | 61mg/L |
[CL] The residual levels of chlorine (hypochlorite ion and hypochlorous acid), chlorine
dioxide, chlorate ion, chloramine and disinfection by-products shall be monitored in the
finished drinking water to ensure compliance to all applicable regulations.
|
||
|
Sulfuric Acid |
||
| Trade Designation | Product Function | Max Use |
| Sulfuric Acid 25% | Corrosion & Scale Control pH Adjustment |
185mg/L |
| Sulfuric Acid 36% | Corrosion & Scale Control pH Adjustment |
129mg/L |
| Sulfuric Acid 50% | Corrosion & Scale Control pH Adjustment |
93mg/L |
| Sulfuric Acid 66BE | Corrosion & Scale Control pH Adjustment |
50mg/L |
| Sulfuric Acid 93% | Corrosion & Scale Control pH Adjustment |
50mg/L |
| Sulfuric Acid 98% | Corrosion & Scale Control pH Adjustment |
50mg/L |
NOTE: Only products bearing the NSF Mark on the product, product packaging, and/or
documentation shipped with the product are Certified.
Facility : Santa Fe Springs, CA
|
Acetic Acid[1] |
||
| Trade Designation | Product Function | Max Use |
| Acetic Acid 50% | Other | 298mg/L |
| Acetic Acid 56% | Other | 266mg/L |
| Acetic Acid 80% | Other | 188mg/L |
| Acetic Acid Glacial | Other | 150mg/L |
[1] This product is designed to function as a reducing agent in biologically active drinking
water treatment systems.
|
||
|
Ammonium Hydroxide |
||
| Trade Designation | Product Function | Max Use |
| Ammonium Hydroxide 15% | Dechlorinator & Antioxidant Chloramination |
33mg/L |
| Ammonium Hydroxide 19% | Dechlorinator & Antioxidant Chloramination |
26mg/L |
| Ammonium Hydroxide 20% | Dechlorinator & Antioxidant Chloramination |
25mg/L |
| Ammonium Hydroxide 26 Be | Dechlorinator & Antioxidant Chloramination |
17mg/L |
| Ammonium Hydroxide 29.4% | Dechlorinator & Antioxidant Chloramination |
17mg/L |
|
Hydrogen Peroxide [HP] |
||
| Trade Designation | Product Function | Max Use |
| Hydrogen Peroxide, 10% | Oxidant | 80mg/L |
| Hydrogen Peroxide, 20% | Oxidant | 40mg/L |
| Hydrogen Peroxide, 25% | 32mg/L | |
| Hydrogen Peroxide, 27.5%[2] | Oxidant | 29mg/L |
| Hydrogen Peroxide, 3% | Oxidant | 266mg/L |
| Hydrogen Peroxide, 30% | Oxidant | 26mg/L |
| Hydrogen Peroxide, 34% | Oxidant | 23mg/L |
| Hydrogen Peroxide, 35% | Oxidant | 23mg/L |
| Hydrogen Peroxide, 50% | Oxidant | 16mg/L |
| Hydrogen Peroxide, 7% | Oxidant | 114mg/L |
[2] This product may be used at a maximum use level of 100 mg/L for the following functions:
- Reoxygenation of treated water
- Oxidation of organic residuals
- Oxidation of any reduced products, such as Fe(II) and sulfides
Treatment must be followed by chlorination to a chlorine residual no to exceed 4 mg/L,
the EPA's proposed maximum residual level.
[HP] Use of this product shall be followed by chlorination to remove levels of hydrogen
peroxide. Chlorine residuals shall not exceed 4 mg/L, the EPA's proposed maximum
residual level.
|
||
|
Miscellaneous Treatment Chemical |
||
| Trade Designation | Product Function | Max Use |
| AquaLAS 40% Plus | Chloramination | 60mg/L |
NOTE: Only products bearing the NSF Mark on the product, product packaging, and/or
documentation shipped with the product are Certified.
Facility : South Gate, CA
|
Aluminum Chlorohydrate[AL] |
||
| Trade Designation | Product Function | Max Use |
| Aluminum Chlorohydrate Solution | Coagulation & Flocculation | 111mg/L |
| PAX XL-19 | Coagulation & Flocculation | 111mg/L |
[AL] Based on an evaluation of health effects data, the level of aluminum in the finished
drinking water shall not exceed 2 mg/L.
|
||
|
Aluminum Sulfate[AL] |
||
| Trade Designation | Product Function | Max Use |
| Aluminum Sulfate | Coagulation & Flocculation | 150mg/L |
[AL] Based on an evaluation of health effects data, the level of aluminum in the finished
drinking water shall not exceed 2 mg/L.
|
||
|
Ammonium Sulfate |
||
| Trade Designation | Product Function | Max Use |
| Ammonium Sulfate 40% | Chloramination | 60mg/L |
| Ammonium Sulfate Solution | Chloramination | 60mg/L |
| AquaLAS 40% | Chloramination | 60mg/L |
| Liquid Ammonium Sulfate | Chloramination | 60mg/L |
|
Blended Phosphates |
||
| Trade Designation | Product Function | Max Use |
| AquaPure 3619 | Corrosion & Scale Control Sequestering |
25mg/L |
| AquaPure 3627 | Corrosion & Scale Control Sequestering |
25mg/L |
| AquaPure 3628 | Corrosion & Scale Control Sequestering |
25mg/L |
| AquaPure 3637 | Corrosion & Scale Control Sequestering |
25mg/L |
| AquaPure 3646 | Corrosion & Scale Control Sequestering |
25mg/L |
| AquaPure 3655 | Corrosion & Scale Control Sequestering |
25mg/L |
| AquaPure 3664 | Corrosion & Scale Control Sequestering |
25mg/L |
| AquaPure 3672 | Corrosion & Scale Control Sequestering |
25mg/L |
| AquaPure 3673 | Corrosion & Scale Control Sequestering |
25mg/L |
| AquaPure 3682 | Corrosion & Scale Control Sequestering |
25mg/L |
| AquaPure 3691 | Corrosion & Scale Control Sequestering |
25mg/L |
| Aquapure 3610 | Corrosion & Scale Control Sequestering |
25mg/L |
|
Citric Acid |
||
| Trade Designation | Product Function | Max Use |
| Citric Acid[4] [5] | Membrane Cleaner | NA |
| Citric Acid | pH Adjustment | 250mg/L |
| Citric Acid 50% | pH Adjustment | 250mg/L |
| Citric Acid 50%[4] [5] | Membrane Cleaner | NA |
| Citric Acid Solution[4] [5] | Membrane Cleaner | NA |
| Citric Acid Solution | pH Adjustment | 250mg/L |
[4] This product is designed to be used off-line and flushed out prior to using the system
for drinking water, following manufacturer's use instructions.
[5] The pH of the influent and effluent water should be monitored to ensure that all traces
of the product have been removed before placing into service.
|
||
|
Copper Sulfate[CP] |
||
| Trade Designation | Product Function | Max Use |
| Copper Sulfate Blend 24 | Algicide | 4mg/L |
[CP] The finished drinking water shall be monitored to ensure that levels of copper do
not exceed 1.3 mg/L.
|
||
|
Ferric Chloride |
||
| Trade Designation | Product Function | Max Use |
| Ferric Chloride | Coagulation & Flocculation | 250mg/L |
| Ferric Chloride 40% | Coagulation & Flocculation | 250mg/L |
| Ferric Chloride Solution | Coagulation & Flocculation | 250mg/L |
|
Ferric Sulfate |
||
| Trade Designation | Product Function | Max Use |
| Ferric Sulfate Solution X[1] | Coagulation & Flocculation | 600mg/L |
[1] X denotes percent strength. |
||
|
Hydrochloric Acid |
||
| Trade Designation | Product Function | Max Use |
| Hydrochloric Acid 15% | Corrosion & Scale Control pH Adjustment |
80mg/L |
| Hydrochloric Acid 18% | Corrosion & Scale Control pH Adjustment |
70mg/L |
| Hydrochloric Acid 20% | Corrosion & Scale Control pH Adjustment |
63mg/L |
| Hydrochloric Acid 20BE | Corrosion & Scale Control pH Adjustment |
40mg/L |
| Hydrochloric Acid 22BE | Corrosion & Scale Control pH Adjustment |
40mg/L |
| Muriatic Acid 15% | Corrosion & Scale Control pH Adjustment |
80mg/L |
| Muriatic Acid 18% | Corrosion & Scale Control pH Adjustment |
70mg/L |
| Muriatic Acid 20% | Corrosion & Scale Control pH Adjustment |
63mg/L |
|
Hydrofluosilicic Acid |
||
| Trade Designation | Product Function | Max Use |
| Fluosilicic Acid | Fluoridation | 6mg/L |
| HFS Acid | Fluoridation | 6mg/L |
| Hydrofluorosilicic Acid 23%-25% | Fluoridation | 6mg/L |
| Hydrofluosilicic Acid | Fluoridation | 6mg/L |
| Hydrofluosilicic Acid 23% | Fluoridation | 6mg/L |
|
Hydroxyethylidene Diphosphonic Acid |
||
| Trade Designation | Product Function | Max Use |
| HEDP | Reverse Osmosis Antiscalant | 10mg/L |
|
Miscellaneous Treatment Chemical |
||
| Trade Designation | Product Function | Max Use |
| Brennsperse 5000 | Reverse Osmosis Antiscalant Distillation Antiscalant |
15mg/L |
| Brenntag CSR 3000 PLUS | Corrosion & Scale Control pH Adjustment |
200mg/L |
| HCR 6000 | Corrosion & Scale Control pH Adjustment |
80mg/L |
| HMDTMP Phosphonate | Reverse Osmosis Antiscalant | 5mg/L |
| HMDTMPA-K6 | Reverse Osmosis Antiscalant | 5mg/L |
| Magnesium Chloride 32% | Precipitation Agent | 125mg/L |
|
Miscellaneous Water Supply Products |
||
| Trade Designation | Product Function | Max Use |
| ATMP | Reverse Osmosis Antiscalant | 10mg/L |
| DEQUEST® 2000 | Reverse Osmosis Antiscalant | 10mg/L |
| DEQUEST® 2010 | Reverse Osmosis Antiscalant | 10mg/L |
| DEQUEST® 2066A | Reverse Osmosis Antiscalant | 10mg/L |
| DETPMPS | Reverse Osmosis Antiscalant | 10mg/L |
| Innova[3] | Well Cleaning Aid | NA |
| Innova 1.0[3] | Well Cleaning Aid | NA |
| Innova 1.5[3] | Well Cleaning Aid | NA |
[3] This product is designed to be used off-line and flushed out prior to using the system
for drinking water, following manufacturer's use instructions. The well is to be
properly flushed and drained before being placed in service.
|
||
|
Monosodium Orthophosphate |
||
| Trade Designation | Product Function | Max Use |
| AquaPure 3601 | Corrosion & Scale Control Sequestering |
25mg/L |
| Monosodium Phosphate | Corrosion & Scale Control Sequestering |
12mg/L |
|
Phosphoric Acid |
||
| Trade Designation | Product Function | Max Use |
| Aquapure Ortho | Corrosion & Scale Control | 26mg/L |
| Phosphoric Acid (36% PO4) | Corrosion & Scale Control | 26mg/L |
| Phosphoric Acid 75% | Corrosion & Scale Control | 13mg/L |
|
Sodium Bisulfite[2] |
||
| Trade Designation | Product Function | Max Use |
| Anti Chlor 30 | Antioxidant | 61mg/L |
| Sodium Bisulfite 25% | Antioxidant | 38mg/L |
| Sodium Bisulfite 30% | Antioxidant | 61mg/L |
| Sodium Bisulfite 38% | Antioxidant | 38mg/L |
| Sodium Bisulfite 40% | Antioxidant | 38mg/L |
[2] This product contains sulfite. Sulfites have been known to cause potentially lethal
allergic reactions in sulfite-sensitive individuals. The maximum recommended allowable
residual sulfite level in the finished drinking water is 100 ppl (0.1 mg/L).
|
||
|
Sodium Carbonate |
||
| Trade Designation | Product Function | Max Use |
| Soda Ash 20% | Precipitation Agent | 150mg/L |
|
Sodium Hydroxide |
||
| Trade Designation | Product Function | Max Use |
| Sodium Hydroxide Solution, 20% | Corrosion & Scale Control pH Adjustment |
250mg/L |
| Sodium Hydroxide Solution, 25% | Corrosion & Scale Control pH Adjustment |
200mg/L |
| Sodium Hydroxide Solution, 30% | Corrosion & Scale Control pH Adjustment |
167mg/L |
| Sodium Hydroxide Solution, 50% | Corrosion & Scale Control pH Adjustment |
100mg/L |
| Sodium Hydroxide, 20% | Corrosion & Scale Control pH Adjustment |
250mg/L |
| Sodium Hydroxide, 25% | Corrosion & Scale Control pH Adjustment |
200mg/L |
| Sodium Hydroxide, 30% | Corrosion & Scale Control pH Adjustment |
167mg/L |
| Sodium Hydroxide, 50% | Corrosion & Scale Control pH Adjustment |
100mg/L |
|
Sodium Hypochlorite[CL] |
||
| Trade Designation | Product Function | Max Use |
| 12.5% Sodium Hypochlorite | Disinfection & Oxidation Algicide |
84mg/L |
| Bacticide | Disinfection & Oxidation Algicide |
84mg/L |
| Bleach 12.5% | Disinfection & Oxidation Algicide |
84mg/L |
| L A Chemchlor | Disinfection & Oxidation Algicide |
84mg/L |
| LA Chemchlor | Disinfection & Oxidation Algicide |
84mg/L |
| Sodium Hypochlorite | Disinfection & Oxidation Algicide |
84mg/L |
| Sodium Hypochlorite 12.5% | Disinfection & Oxidation Algicide |
84mg/L |
| Sodium Hypochlorite Solution | Disinfection & Oxidation Algicide |
84mg/L |
[CL] The residual levels of chlorine (hypochlorite ion and hypochlorous acid), chlorine
dioxide, chlorate ion, chloramine and disinfection by-products shall be monitored in the
finished drinking water to ensure compliance to all applicable regulations.
|
||
|
Sodium Permanganate[PO] |
||
| Trade Designation | Product Function | Max Use |
| Sodium Permanganate 5% | Oxidant | 896mg/L |
| Sodium Permanganate, 20% | Oxidant | 224mg/L |
| Sodium Permanganate, 40% | Oxidant | 112mg/L |
[PO] The finished drinking water shall be monitored to ensure that levels of manganese
do not exceed 0.05 mg/L.
|
||
|
Sodium Polyphosphates, Glassy |
||
| Trade Designation | Product Function | Max Use |
| Sodium Hexametaphosphate 35% | Corrosion & Scale Control Sequestering |
23mg/L |
| Sodium Hexametaphosphate 40% | Corrosion & Scale Control Sequestering |
23mg/L |
|
Sodium Silicate |
||
| Trade Designation | Product Function | Max Use |
| Sodium Silicate N Clear | Corrosion & Scale Control Sequestering |
42mg/L |
|
Sulfuric Acid |
||
| Trade Designation | Product Function | Max Use |
| Sulfuric Acid 25% | Corrosion & Scale Control pH Adjustment |
185mg/L |
| Sulfuric Acid 36% | Corrosion & Scale Control pH Adjustment |
129mg/L |
| Sulfuric Acid 50% | Corrosion & Scale Control pH Adjustment |
93mg/L |
| Sulfuric Acid 66BE | Corrosion & Scale Control pH Adjustment |
50mg/L |
| Sulfuric Acid 93% | Corrosion & Scale Control pH Adjustment |
50mg/L |
| Sulfuric Acid 98% | Corrosion & Scale Control pH Adjustment |
50mg/L |
|
Zinc Orthophosphate[ZN] |
||
| Trade Designation | Product Function | Max Use |
| LAC 101-CM | Corrosion & Scale Control | 25mg/L |
| LAC 101C-22 | Corrosion & Scale Control | 10mg/L |
| LAC 301-CK | Corrosion & Scale Control | 15mg/L |
| LAC-1001-S | Corrosion & Scale Control | 25mg/L |
| LAC-101 C | Corrosion & Scale Control | 16mg/L |
| LAC-101-S | Corrosion & Scale Control | 20mg/L |
| LAC-301 C | Corrosion & Scale Control | 15mg/L |
| LAC-301-S | Corrosion & Scale Control | 16mg/L |
| LAC-501-C | Corrosion & Scale Control | 25mg/L |
| LAC-501-S | Corrosion & Scale Control | 15mg/L |
[ZN] Based on an evaluation of health effects data, the level of zinc in the finished
drinking water shall not exceed 2.0 mg/L.
|
||
|
Zinc Sulfate[ZN] |
||
| Trade Designation | Product Function | Max Use |
| Zinc Sulfate | Corrosion Control | 4mg/L |
[ZN] Based on an evaluation of health effects data, the level of zinc in the finished
drinking water shall not exceed 2.0 mg/L.
|
||
NOTE: Only products bearing the NSF Mark on the product, product packaging, and/or
documentation shipped with the product are Certified.
Facility : Wilmington, CA
|
Sodium Hydroxide |
||
| Trade Designation | Product Function | Max Use |
| Sodium Hydroxide 50% | Corrosion & Scale Control pH Adjustment |
100mg/L |
| Sodium Hydroxide Solution | Corrosion & Scale Control pH Adjustment |
100mg/L |
NOTE: Only products bearing the NSF Mark on the product, product packaging, and/or
documentation shipped with the product are Certified.
Facility : Billings, MT
|
Sodium Hypochlorite[CL] |
||
| Trade Designation | Product Function | Max Use |
| 12.5% Sodium Hypochlorite | Disinfection & Oxidation | 76mg/L |
| Bleach 12.5% | Disinfection & Oxidation | 76mg/L |
| L.A. Chemchlor 12.5% | Disinfection & Oxidation | 76mg/L |
| Sodium Hypochlorite | Disinfection & Oxidation | 76mg/L |
| Sodium Hypochlorite 12.5% | Disinfection & Oxidation | 76mg/L |
[CL] The residual levels of chlorine (hypochlorite ion and hypochlorous acid), chlorine
dioxide, chlorate ion, chloramine and disinfection by-products shall be monitored in the
finished drinking water to ensure compliance to all applicable regulations.
|
||
NOTE: Only products bearing the NSF Mark on the product, product packaging, and/or
documentation shipped with the product are Certified.
Facility : Distribution Center - Las Vegas, NV
|
Hydrofluosilicic Acid |
||
| Trade Designation | Product Function | Max Use |
| Hydrofluorosilicic Acid 23% | Fluoridation | 6mg/L |
NOTE: Only products bearing the NSF Mark on the product, product packaging, and/or
documentation shipped with the product are Certified.
Facility : North Las Vegas, NV
|
Sodium Hypochlorite[CL] |
||
| Trade Designation | Product Function | Max Use |
| 12.5% Sodium Hypochlorite | Algicide Disinfection & Oxidation |
84mg/L |
| Bleach 12.5% | Algicide Disinfection & Oxidation |
84mg/L |
| L A Chemchlor | Algicide Disinfection & Oxidation |
84mg/L |
| Sodium Hypochlorite 12.5% | Algicide Disinfection & Oxidation |
84mg/L |
[CL] The residual levels of chlorine (hypochlorite ion and hypochlorous acid), chlorine
dioxide, chlorate ion, chloramine and disinfection by-products shall be monitored in the
finished drinking water to ensure compliance to all applicable regulations.
|
||
NOTE: Only products bearing the NSF Mark on the product, product packaging, and/or
documentation shipped with the product are Certified.
Facility : Portland, OR
|
Aluminum Chlorohydrate[AL] |
||
| Trade Designation | Product Function | Max Use |
| Aluminum Chlorohydrate Solution | Coagulation & Flocculation | 111mg/L |
| PAX XL-19 | Coagulation & Flocculation | 111mg/L |
[AL] Based on an evaluation of health effects data, the level of aluminum in the finished
drinking water shall not exceed 2 mg/L.
|
||
|
Aluminum Sulfate[AL] |
||
| Trade Designation | Product Function | Max Use |
| Aluminum Sulfate | Coagulation & Flocculation | 150mg/L |
[AL] Based on an evaluation of health effects data, the level of aluminum in the finished
drinking water shall not exceed 2 mg/L.
|
||
|
Ammonium Sulfate |
||
| Trade Designation | Product Function | Max Use |
| Ammonium Sulfate 40% | Chloramination | 60mg/L |
| Ammonium Sulfate Solution | Chloramination | 60mg/L |
| AquaLAS 40% | Chloramination | 60mg/L |
| Liquid Ammonium Sulfate | Chloramination | 60mg/L |
|
Citric Acid |
||
| Trade Designation | Product Function | Max Use |
| Citric Acid 50%[1] [2] | Membrane Cleaner | NA |
| Citric Acid 50% | pH Adjustment | 250mg/L |
| Citric Acid Solution[1] [2] | Membrane Cleaner | NA |
| Citric Acid Solution | pH Adjustment | 250mg/L |
[1] This product is designed to be used off-line and flushed out prior to using the system
for drinking water, following manufacturer's use instructions.
[2] The pH of the influent and effluent water should be monitored to ensure that all traces
of the product have been removed before placing into service.
|
||
|
Hydrochloric Acid |
||
| Trade Designation | Product Function | Max Use |
| Hydrochloric Acid 15% | Corrosion & Scale Control pH Adjustment |
80mg/L |
| Hydrochloric Acid 18% | Corrosion & Scale Control pH Adjustment |
70mg/L |
| Hydrochloric Acid 20% | Corrosion & Scale Control pH Adjustment |
63mg/L |
| Hydrochloric Acid 20BE | Corrosion & Scale Control pH Adjustment |
40mg/L |
| Hydrochloric Acid 22BE | Corrosion & Scale Control pH Adjustment |
40mg/L |
| Muriatic Acid 15% | Corrosion & Scale Control pH Adjustment |
80mg/L |
| Muriatic Acid 18% | Corrosion & Scale Control pH Adjustment |
70mg/L |
| Muriatic Acid 20% | Corrosion & Scale Control pH Adjustment |
63mg/L |
|
Potassium Hydroxide |
||
| Trade Designation | Product Function | Max Use |
| Potassium Hydroxide 45% | Corrosion & Scale Control pH Adjustment |
100mg/L |
| Potassium Hydroxide 45% Solution | Corrosion & Scale Control pH Adjustment |
100mg/L |
|
Sodium Bisulfite[3] |
||
| Trade Designation | Product Function | Max Use |
| Anti Chlor 30 | Antioxidant | 61mg/L |
| Sodium Bisulfite 25% | Antioxidant | 38mg/L |
| Sodium Bisulfite 30% | Antioxidant | 61mg/L |
| Sodium Bisulfite 38% | Antioxidant | 38mg/L |
| Sodium Bisulfite 40% | Antioxidant | 38mg/L |
[3] This product contains sulfite. Sulfites have been known to cause potentially lethal
allergic reactions in sulfite-sensitive individuals. The maximum recommended allowable
residual sulfite level in the finished drinking water is 100 ppb (0.1 mg/L).
|
||
|
Sodium Hydroxide |
||
| Trade Designation | Product Function | Max Use |
| Caustic Soda 25% | Corrosion & Scale Control pH Adjustment |
200mg/L |
| Caustic Soda Solution 25% | Corrosion & Scale Control pH Adjustment |
200mg/L |
| Caustic Soda Solution, 50% | Corrosion & Scale Control pH Adjustment |
100mg/L |
| Sodium Hydroxide 25% | Corrosion & Scale Control pH Adjustment |
200mg/L |
| Sodium Hydroxide Solution 25% | Corrosion & Scale Control pH Adjustment |
200mg/L |
| Sodium Hydroxide Solution, 50% | Corrosion & Scale Control pH Adjustment |
100mg/L |
| Sodium Hydroxide, 50% | Corrosion & Scale Control pH Adjustment |
100mg/L |
|
Sodium Hypochlorite[CL] |
||
| Trade Designation | Product Function | Max Use |
| 12.5% Sodium Hypochlorite | Disinfection & Oxidation Algicide |
84mg/L |
| Bacticide | Disinfection & Oxidation Algicide |
84mg/L |
| Bleach 12.5% | Disinfection & Oxidation Algicide |
84mg/L |
| L A Chemchlor | Disinfection & Oxidation Algicide |
84mg/L |
| LA Chemchlor | Disinfection & Oxidation Algicide |
84mg/L |
| Sodium Hypochlorite | Disinfection & Oxidation Algicide |
84mg/L |
| Sodium Hypochlorite 12.5% | Disinfection & Oxidation Algicide |
84mg/L |
| Sodium Hypochlorite Solution | Disinfection & Oxidation Algicide |
84mg/L |
[CL] The residual levels of chlorine (hypochlorite ion and hypochlorous acid), chlorine
dioxide, chlorate ion, chloramine and disinfection by-products shall be monitored in the
finished drinking water to ensure compliance to all applicable regulations.
|
||
|
Sulfuric Acid |
||
| Trade Designation | Product Function | Max Use |
| Sulfuric Acid 25% | Corrosion & Scale Control pH Adjustment |
185mg/L |
| Sulfuric Acid 36% | Corrosion & Scale Control pH Adjustment |
129mg/L |
| Sulfuric Acid 50% | Corrosion & Scale Control pH Adjustment |
93mg/L |
| Sulfuric Acid 66BE | Corrosion & Scale Control pH Adjustment |
50mg/L |
| Sulfuric Acid 93% | Corrosion & Scale Control pH Adjustment |
50mg/L |
| Sulfuric Acid 98% | Corrosion & Scale Control pH Adjustment |
50mg/L |
|
Tetrapotassium Pyrophosphate |
||
| Trade Designation | Product Function | Max Use |
| Tetrapotassium Pyrophosphate 60% Solution | Corrosion & Scale Control Sequestering |
29mg/L |
NOTE: Only products bearing the NSF Mark on the product, product packaging, and/or
documentation shipped with the product are Certified.
Number of matching Manufacturers is 1
Number of matching Products is 329
Processing time was 0 seconds
