NSF Product and Service Listings

[ZN] Based on an evaluation of health effects data, the level of zinc in the finished
     drinking water shall not exceed 2.0 mg/L.

[AL] Based on an evaluation of health effects data, the level of aluminum in the finished
     drinking water shall not exceed 2 mg/L.

[AL] Based on an evaluation of health effects data, the level of aluminum in the finished
     drinking water shall not exceed 2 mg/L.

[1] This product contains copper and may increase the amount of copper present in the
    finished drinking water.  Following use of this product, the finished drinking water
    should be monitored to ensure the levels of copper do not exceed regulatory requirements.
[AL] Based on an evaluation of health effects data, the level of aluminum in the finished
     drinking water shall not exceed 2 mg/L.
[PY] Polyamines Certified by NSF International comply with 40 CFR 141.111 requirements for
     percent monomer and dose.

[PY] Polyamines Certified by NSF International comply with 40 CFR 141.111 requirements for
     percent monomer and dose.

[AL] Based on an evaluation of health effects data, the level of aluminum in the finished
     drinking water shall not exceed 2 mg/L.
[PY] Polyamines Certified by NSF International comply with 40 CFR 141.111 requirements for
     percent monomer and dose.

[ZN] Based on an evaluation of health effects data, the level of zinc in the finished
     drinking water shall not exceed 2.0 mg/L.

[ZN] Based on an evaluation of health effects data, the level of zinc in the finished
     drinking water shall not exceed 2.0 mg/L.

[PY] Polyamines Certified by NSF International comply with 40 CFR 141.111 requirements
     forpercent monomer and dose.

[AL] Based on an evaluation of health effects data, the level of aluminum in the finished
     drinking water shall not exceed 2 mg/L.

[PY] Polyamines Certified by NSF International comply with 40 CFR 141.111 requirements for
     percent monomer and dose.

[1] These products are certified for use in chlorine dioxide generation.
[CL] The residual levels of chlorine (hypochlorite ion and hypochlorous acid), chlorine
     dioxide, chlorate ion, chloramine and disinfection by-products shall be monitored in the
     finished drinking water to ensure compliance to all applicable regulations.

[AL] Based on an evaluation of health effects data, the level of aluminum in the finished
     drinking water shall not exceed 2 mg/L.

[1] Certified for addition to the feedwater for reverse osmosis applications only.
[2] This product is to be added to the feed water for evaporative desalination units only.

[PC] Polyacrylamide Products Certified by NSF International comply with 40 CFR 141.111
     requirements for percent monomer and dose.

[PY] Polyamines Certified by NSF International comply with 40 CFR 141.111 requirements for
     percent monomer and dose.

[AL] Based on an evaluation of health effects data, the level of aluminum in the finished
     drinking water shall not exceed 2 mg/L.

[AL] Based on an evaluation of health effects data, the level of aluminum in the finished
     drinking water shall not exceed 2 mg/L.

[3] This product contains sulfite.  Sulfites have been known to cause potentially lethal
    allergic reactions in sulfite-sensitive individuals.  The maximum recommended allowable
    residual sulfite level in the finished drinking water is 100 ppb (0.1 mg/L).

[4] These products are certified for use in chlorine dioxide generation.
[CL] The residual levels of chlorine (hypochlorite ion and hypochlorous acid), chlorine
     dioxide, chlorate ion, chloramine and disinfection by-products shall be monitored in the
     finished drinking water to ensure compliance to all applicable regulations.

[HY] The residual levels of chlorine (hypochlorite ion and hypochlorous acid), chlorine
     dioxide, chlorate ion, chloramine and disinfection by-products shall be monitored in the
     finished drinking water to ensure compliance to all applicable regulations. Also,
     reference the AWWA B300 (Hypochlorites) standard's Recommendations for the Handling and
     Storage of Hypochlorite Solutions appendix for information on preservation techniques
     for hypochlorite bleach in transit and storage.

[ZN] Based on an evaluation of health effects data, the level of zinc in the finished
     drinking water shall not exceed 2.0 mg/L.

[ZN] Based on an evaluation of health effects data, the level of zinc in the finished
     drinking water shall not exceed 2.0 mg/L.

[1] These products are designed to be flushed out prior to using the system for drinking
    water. Before being placed into service, the well is to be properly flushed according to
    the manufacturer's use instructions. Certification of these products is based on the
    well drilling model with the following assumptions:
    - The amount of well drilling fluid used is 3780 L (1000 U.S. gallons) to which the
    drilling fluid has been added at the manufacturer's recommended level.
    - The aquifer contains 3.1 million liters of water (815,000 gallons) based on a 0.5 acre
    aquifer of 6.1 meter depth (20 ft.) and 25% porosity.
    - The bore hole is 61 meters in total depth (200 ft.), the screen is 6.1 meters in
    length (20 ft.), and the bore hole is 25.4 cm. in diameter (10 in.).
    - The amount of well drilling fluid removed from the well during construction is equal
    to the combined volumes of the casing and the screen, plus an additional amount removed
    through the well disinfection and development (90% removed).
    - This product should not be used in constructing wells in highly porous formations,
    such as cavernous limestone.
[PC] Polyacrylamide Products Certified by NSF International comply with 40 CFR 141.111
     requirements for percent monomer and dose.