NSF Product and Service Listings

These NSF Official Listings are current as of Wednesday, July 2, 2025 at 12:15 a.m. Eastern Time. Please contact NSF to confirm the status of any Listing, report errors, or make suggestions.

Alert: NSF is concerned about fraudulent downloading and manipulation of website text. Always confirm this information by clicking on the below link for the most accurate information: http://info.nsf.org/Certified/PwsChemicals/Listings.asp?Company=34960&Standard=060&


NSF/ANSI/CAN 60
Drinking Water Treatment Chemicals - Health Effects



 
Brenntag Mid-South, Inc. 
1405 Highway 136 West
P.O. Box 20 
Henderson, KY 42420-0020 
United States 
800-950-7267 
270-827-3545
Visit this company's website

Facility : Clearwater, FL


Hydrochloric Acid
Trade Designation Product Function Max Use
Hydrochloric Acid 20 BE Corrosion & Scale Control 44mg/L
Hydrochloric Acid 20 BE/31.45 Corrosion & Scale Control 44mg/L
Hydrochloric Acid 28% Corrosion & Scale Control 50mg/L
Hydrochloric Acid 31.45% Corrosion & Scale Control 44mg/L
Hydrochloric Acid 32% Corrosion & Scale Control 44mg/L
Muriatic Acid 20 DEG BE Corrosion & Scale Control 44mg/L
Muriatic Acid 22 DEG BE Corrosion & Scale Control 40mg/L

Sodium Hypochlorite[HY]
Trade Designation Product Function Max Use
SNO-GLO BLEACH Disinfection & Oxidation 105mg/L
Sno-Glo 10% Bleach Disinfection & Oxidation 105mg/L
Sodium Hypochlorite 10.5% Disinfection & Oxidation 100mg/L
Sodium Hypochlorite 12.5% Disinfection & Oxidation 84mg/L
Sodium Hypochlorite, 10% Disinfection & Oxidation 105mg/L

[HY] The residual levels of chlorine (hypochlorite ion and hypochlorous acid), chlorine
     dioxide, chlorate ion, chloramine and disinfection by-products shall be monitored in the
     finished drinking water to ensure compliance to all applicable regulations. Also,
     reference the AWWA B300 (Hypochlorites) standard's Recommendations for the Handling and
     Storage of Hypochlorite Solutions appendix for information on preservation techniques
     for hypochlorite bleach in transit and storage.

Sulfuric Acid
Trade Designation Product Function Max Use
Sulfuric Acid 15% Corrosion & Scale Control
pH Adjustment
260mg/L
Sulfuric Acid 38.5% Corrosion & Scale Control
pH Adjustment
120mg/L
Sulfuric Acid 50% Corrosion & Scale Control
pH Adjustment
93mg/L
Sulfuric Acid 66 BE pH Adjustment
Corrosion & Scale Control
50mg/L
Sulfuric Acid 66 DEG Corrosion & Scale Control
pH Adjustment
50mg/L
Sulfuric Acid 78% pH Adjustment
Corrosion & Scale Control
60mg/L
Sulfuric Acid 93% Corrosion & Scale Control
pH Adjustment
50mg/L

NOTE: Only products bearing the NSF Mark on the product, product packaging, and/or
      documentation shipped with the product are Certified.

Facility : Miami, FL


Sodium Hydroxide[1]
Trade Designation Product Function Max Use
Caustic Soda 20% Corrosion & Scale Control 250mg/L
Caustic Soda 25% Corrosion & Scale Control 200mg/L
Caustic Soda 50% Corrosion & Scale Control 100mg/L
Sodium Hydroxide 20% Corrosion & Scale Control 250mg/L
Sodium Hydroxide 25% Corrosion & Scale Control 200mg/L
Sodium Hydroxide 50% Corrosion & Scale Control 100mg/L

[1] Trade designation may be followed by a three digit alpha suffix to designate the
    chlor-alkali electrolytic cell category/grade.


Facility : Orlando, FL


Aluminum Sulfate[AL]
Trade Designation Product Function Max Use
Aluminum Sulfate 50% Coagulation & Flocculation 150mg/L
Aluminum Sulfate 50% SOLN Coagulation & Flocculation 150mg/L
Aluminum Sulfate 50% Solution Coagulation & Flocculation 150mg/L
Aluminum Sulfate Solution Coagulation & Flocculation 150 mg/L
Liquid Alum Coagulation & Flocculation 150 mg/L

[AL] Based on an evaluation of health effects data, the level of aluminum in the finished
     drinking water shall not exceed 2 mg/L.

Chlorine[CL]
Trade Designation Product Function Max Use
Chlorine, Liquified Gas Disinfection & Oxidation 30 mg/L

[CL] The residual levels of chlorine (hypochlorite ion and hypochlorous acid), chlorine
     dioxide, chlorate ion, chloramine and disinfection by-products shall be monitored in the
     finished drinking water to ensure compliance to all applicable regulations.

Ferric Chloride
Trade Designation Product Function Max Use
Ferric Chloride 38-42% Coagulation & Flocculation 250mg/L
Ferric Chloride Liquid Coagulation & Flocculation 250 mg/L
Ferric Chloride Solution Coagulation & Flocculation 250 mg/L
Iron (III) Chloride Solution Coagulation & Flocculation 250mg/L
Iron Trichloride Solution Coagulation & Flocculation 250mg/L

Hydrochloric Acid
Trade Designation Product Function Max Use
Hydrochloric Acid 15% Corrosion & Scale Control
pH Adjustment
80mg/L
Hydrochloric Acid 20 BE Corrosion & Scale Control 44mg/L
Hydrochloric Acid 20 BE / 31.45 Corrosion & Scale Control 44mg/L
Hydrochloric Acid 28% Corrosion & Scale Control 50mg/L
Hydrochloric Acid 31.45% Corrosion & Scale Control 44mg/L
Hydrochloric Acid 32% Corrosion & Scale Control 44mg/L
Muriatic Acid Corrosion & Scale Control 44mg/L
Muriatic Acid 10% Corrosion & Scale Control 138mg/L
Muriatic Acid 15% Corrosion & Scale Control
pH Adjustment
80mg/L
Muriatic Acid 20 DEG BE Corrosion & Scale Control 44mg/L
Muriatic Acid 22 DEG BE Corrosion & Scale Control 40mg/L

Sodium Bisulfite[1]
Trade Designation Product Function Max Use
Sodium Bisulfite 19-44% Dechlorinator & Antioxidant 46mg/L
Sodium Hydrogen Sulfite 40% Dechlorinator & Antioxidant 46mg/L

[1] This product contains sulfite.
   Sulfites have been known to cause potentially lethal allergic reactions in sulfite-sensitive individuals.
   The maximum recommended allowable residual sulfite level in the finished drinking water is 100 ppb (0.1 mg/L).

Sodium Hydroxide[2]
Trade Designation Product Function Max Use
Caustic Soda 20% Corrosion & Scale Control 250 mg/L
Caustic Soda 25% Corrosion & Scale Control 200 mg/L
Caustic Soda 50% Corrosion & Scale Control 100 mg/L
Sodium Hydroxide 20% Corrosion & Scale Control 250mg/L
Sodium Hydroxide 25% Corrosion & Scale Control 200mg/L
Sodium Hydroxide 50% Corrosion & Scale Control 100mg/L

[2] Trade designation may be followed by a three digit alpha suffix to designate the
    chlor-alkali electrolytic cell category/grade.

Sodium Hypochlorite[HY]
Trade Designation Product Function Max Use
SNO-GLO BLEACH Disinfection & Oxidation 105mg/L
Sno-Glo 10% Bleach Disinfection & Oxidation 105 mg/L
Sodium Hypochlorite 12.5% Disinfection & Oxidation 84 mg/L
Sodium Hypochlorite, 10% Disinfection & Oxidation 105 mg/L

[HY] The residual levels of chlorine (hypochlorite ion and hypochlorous acid), chlorine
     dioxide, chlorate ion, chloramine and disinfection by-products shall be monitored in the
     finished drinking water to ensure compliance to all applicable regulations. Also,
     reference the AWWA B300 (Hypochlorites) standard's Recommendations for the Handling and
     Storage of Hypochlorite Solutions appendix for information on preservation techniques
     for hypochlorite bleach in transit and storage.

Sulfuric Acid
Trade Designation Product Function Max Use
Sulfuric Acid 66 BE Corrosion & Scale Control 50mg/L
Sulfuric Acid 66 DEG Corrosion & Scale Control 50mg/L
Sulfuric Acid 93% Corrosion & Scale Control 50mg/L

NOTE: Only products bearing the NSF Mark on the product, product packaging, and/or 
      documentation shipped with the product are Certified.

Facility : Tampa, FL


Ammonium Sulfate
Trade Designation Product Function Max Use
Ammonium Sulfate 38.5% Sol Chloramination 60mg/L
Ammonium Sulfate 40% Chloramination 60mg/L
Ammonium Sulfate 40% Sol Chloramination 60mg/L
WWT 9710 Chloramination 60mg/L

Citric Acid[1]
Trade Designation Product Function Max Use
Citric Acid 50% Membrane Cleaner NA
Citric Acid Solution Membrane Cleaner NA

[1] These products are designed to be used off-line and flushed out prior to using the
    system for drinking water, following manufacturer's use instructions.  The pH of the
    influent and effluent water should be monitored to ensure that all traces of the product
    have been removed before placing into service.

Hydrochloric Acid
Trade Designation Product Function Max Use
Hydrochloric Acid 15% Corrosion & Scale Control
pH Adjustment
80mg/L
Hydrochloric Acid 20 BE Corrosion & Scale Control 44mg/L
Hydrochloric Acid 20 BE / 31.45 Corrosion & Scale Control 44mg/L
Hydrochloric Acid 28% Corrosion & Scale Control 50mg/L
Hydrochloric Acid 31.45% Corrosion & Scale Control 44mg/L
Hydrochloric Acid 32% Corrosion & Scale Control 44mg/L
Muriatic Acid Corrosion & Scale Control 44mg/L
Muriatic Acid 10% Corrosion & Scale Control 138mg/L
Muriatic Acid 15% Corrosion & Scale Control
pH Adjustment
80mg/L
Muriatic Acid 20 DEG BE Corrosion & Scale Control 44mg/L
Muriatic Acid 22 DEG BE Corrosion & Scale Control 40mg/L

Sodium Bisulfite[2]
Trade Designation Product Function Max Use
Sodium Bisulfite 19-44% Dechlorinator & Antioxidant 46mg/L
Sodium Hydrogen Sulfite 40% Dechlorinator & Antioxidant 46mg/L

[2] This product contains sulfite.  Sulfites have been known to cause potentially lethal
    allergic reactions in sulfite-sensitive individuals.  The maximum
    recommended allowable residual sulfite level in the finished drinking water is 100 ppb
    (0.1 mg/L).

Sodium Hydroxide[3]
Trade Designation Product Function Max Use
Caustic Soda 25% Corrosion & Scale Control 200mg/L
Caustic Soda 50% Corrosion & Scale Control 100mg/L
Sodium Hydroxide 50% DIA Corrosion & Scale Control 100mg/L
Sodium Hydroxide 50% MEM Corrosion & Scale Control 100mg/L
Sodium Hydroxide Solution 25% Corrosion & Scale Control 200mg/L
Sodium Hydroxide Solution 50% Corrosion & Scale Control 100mg/L

[3] Trade designation may be followed by a three digit alpha suffix to designate the
    chlor-alkali electrolytic cell category/grade.

Sodium Hypochlorite[HY]
Trade Designation Product Function Max Use
Sodium Hypochlorite 10% Disinfection & Oxidation 70mg/L

[HY] The residual levels of chlorine (hypochlorite ion and hypochlorous acid), chlorine
     dioxide, chlorate ion, chloramine and disinfection by-products shall be monitored in the
     finished drinking water to ensure compliance to all applicable regulations. Also,
     reference the AWWA B300 (Hypochlorites) standard's Recommendations for the Handling and
     Storage of Hypochlorite Solutions appendix for information on preservation techniques
     for hypochlorite bleach in transit and storage.

Sulfuric Acid
Trade Designation Product Function Max Use
Sulfuric Acid 15% Corrosion & Scale Control
pH Adjustment
260mg/L
Sulfuric Acid 38.5% Corrosion & Scale Control
pH Adjustment
120mg/L
Sulfuric Acid 50% Corrosion & Scale Control
pH Adjustment
93mg/L
Sulfuric Acid 66 BE pH Adjustment
Corrosion & Scale Control
50mg/L
Sulfuric Acid 66 DEG Corrosion & Scale Control
pH Adjustment
50mg/L
Sulfuric Acid 78% pH Adjustment
Corrosion & Scale Control
60mg/L
Sulfuric Acid 93% Corrosion & Scale Control
pH Adjustment
50mg/L

NOTE: Only products bearing the NSF Mark on the product, product packaging, and/or
      documentation shipped with the product are Certified.

Facility : Eastpoint, GA


Aluminum Chlorohydrate[AL]
Trade Designation Product Function Max Use
Prestofloc C-100 Coagulation & Flocculation 250mg/L

[AL] Based on an evaluation of health effects data, the level of aluminum in the finished
     drinking water shall not exceed 2 mg/L.

Ferric Chloride
Trade Designation Product Function Max Use
Ferric Chloride 38-42% Coagulation & Flocculation 250mg/L
Ferric Chloride Liquid Coagulation & Flocculation 250mg/L
Ferric Chloride Solution Coagulation & Flocculation 250mg/L
Iron (III) Chloride Solution Coagulation & Flocculation 250mg/L
Iron Trichloride Solution Coagulation & Flocculation 250mg/L

Sodium Bisulfite[2]
Trade Designation Product Function Max Use
Sodium Bisulfite 19-44% Dechlorinator & Antioxidant 46mg/L
Sodium Hydrogen Sulfite 40% Dechlorinator & Antioxidant 46mg/L

[2] This product contains sulfite. Sulfites have been known to cause potentially lethal
    allergic reactions in sulfite-sensitive individuals. The maximum recommended allowable
    residual sulfite level in the finished drinking water is 100 ppb (0.1 mg/L).

Sodium Hydroxide[1]
Trade Designation Product Function Max Use
Caustic Soda 10% Corrosion & Scale Control
pH Adjustment
500mg/L
Caustic Soda 20% Corrosion & Scale Control
pH Adjustment
250mg/L
Caustic Soda 25% Corrosion & Scale Control
pH Adjustment
200mg/L
Caustic Soda 30% Corrosion & Scale Control
pH Adjustment
166mg/L
Caustic Soda 50% Corrosion & Scale Control
pH Adjustment
100mg/L
Sodium Hydroxide 10% Corrosion & Scale Control
pH Adjustment
500mg/L
Sodium Hydroxide 20% Corrosion & Scale Control
pH Adjustment
250mg/L
Sodium Hydroxide 25% Corrosion & Scale Control
pH Adjustment
200mg/L
Sodium Hydroxide 30% Corrosion & Scale Control
pH Adjustment
166mg/L
Sodium Hydroxide 50% Corrosion & Scale Control
pH Adjustment
100mg/L

[1] Trade Designation may be followed by a three digit alpha suffix to designate the
    chlor-alkali electrolytic cell category/grade.

Sodium Hypochlorite[HY]
Trade Designation Product Function Max Use
Sodium Hypochlorite 10% Disinfection & Oxidation 105mg/L
Sodium Hypochlorite 12.5% Disinfection & Oxidation 84mg/L

[HY] The residual levels of chlorine (hypochlorite ion and hypochlorous acid), chlorine
     dioxide, chlorate ion, chloramine and disinfection by-products shall be monitored in the
     finished drinking water to ensure compliance to all applicable regulations. Also,
     reference the AWWA B300 (Hypochlorites) standard's Recommendations for the Handling and
     Storage of Hypochlorite Solutions appendix for information on preservation techniques
     for hypochlorite bleach in transit and storage.

Sulfuric Acid
Trade Designation Product Function Max Use
Sulfuric Acid Corrosion & Scale Control
pH Adjustment
50mg/L
Sulfuric Acid 66 Corrosion & Scale Control
pH Adjustment
50mg/L
Sulfuric Acid 66 Baumé Corrosion & Scale Control
pH Adjustment
50mg/L
Sulfuric Acid 66Be Corrosion & Scale Control
pH Adjustment
50mg/L
Sulfuric Acid 93% Corrosion & Scale Control
pH Adjustment
50mg/L

NOTE: Only products bearing the NSF Mark on the product, packing, and/or documentation shipped
      with the product are Certified.

Facility : Savannah, GA


Sodium Hydroxide
Trade Designation Product Function Max Use
Caustic Soda 50% Corrosion & Scale Control 100mg/L
Sodium Hydroxide 50% Corrosion & Scale Control 100mg/L


Facility : Valdosta, GA


Sodium Hydroxide[1]
Trade Designation Product Function Max Use
Caustic Soda 10% Corrosion & Scale Control
pH Adjustment
500mg/L
Caustic Soda 20% Corrosion & Scale Control
pH Adjustment
250mg/L
Caustic Soda 25% Corrosion & Scale Control
pH Adjustment
200mg/L
Caustic Soda 30% Corrosion & Scale Control
pH Adjustment
166mg/L
Caustic Soda 50% Corrosion & Scale Control
pH Adjustment
100mg/L
Sodium Hydroxide 10% Corrosion & Scale Control
pH Adjustment
500mg/L
Sodium Hydroxide 20% Corrosion & Scale Control
pH Adjustment
250mg/L
Sodium Hydroxide 25% Corrosion & Scale Control
pH Adjustment
200mg/L
Sodium Hydroxide 30% Corrosion & Scale Control
pH Adjustment
166mg/L
Sodium Hydroxide 50% Corrosion & Scale Control
pH Adjustment
100mg/L

[1] Trade Designation may be followed by a three digit alpha suffix to designate the
    chlor-alkali electrolytic cell category/grade.

Sodium Hypochlorite[HY]
Trade Designation Product Function Max Use
SNO-GLO BLEACH Disinfection & Oxidation 82mg/L
Sno-Glo 10% Bleach Disinfection & Oxidation 82mg/L
Sodium Hypochlorite 10% Disinfection & Oxidation 82mg/L
Sodium Hypochlorite 10.5% Disinfection & Oxidation 79mg/L
Sodium Hypochlorite 12.5% Disinfection & Oxidation 66mg/L

[HY] The residual levels of chlorine (hypochlorite ion and hypochlorous acid), chlorine
     dioxide, chlorate ion, chloramine and disinfection by-products shall be monitored in the
     finished drinking water to ensure compliance to all applicable regulations. Also,
     reference the AWWA B300 (Hypochlorites) standard's Recommendations for the Handling and
     Storage of Hypochlorite Solutions appendix for information on preservation techniques
     for hypochlorite bleach in transit and storage.

NOTE: Only products bearing the NSF Mark on the product, packing, and/or documentation shipped
      with the product are Certified.

Facility : Distribution Center - East St. Louis, IL


Phosphoric Acid
Trade Designation Product Function Max Use
PHOSPHORIC ACID 75% Corrosion & Scale Control
Softener
13mg/L

Sulfuric Acid
Trade Designation Product Function Max Use
Sulfuric Acid 66 BE Corrosion & Scale Control 50mg/L
Sulfuric Acid 66 DEG Corrosion & Scale Control 50mg/L
Sulfuric Acid 93% Corrosion & Scale Control 50mg/L

NOTE: Only products bearing the NSF Mark on the product, product packaging, and/or
      documentation shipped with the product are Certified.

Facility : East St. Louis, IL


Sodium Carbonate
Trade Designation Product Function Max Use
Soda Ash pH Adjustment
Corrosion & Scale Control
150mg/L
Soda Ash Dense pH Adjustment
Corrosion & Scale Control
150mg/L
Soda Ash Light pH Adjustment
Corrosion & Scale Control
150mg/L
Sodium Carbonate pH Adjustment
Corrosion & Scale Control
150mg/L


Facility : Fairmont City, IL


Aluminum Chlorohydrate[AL]
Trade Designation Product Function Max Use
Brennfloc BC4105[PY] Coagulation & Flocculation 31mg/L

[AL] Based on an evaluation of health effects data, the level of aluminum in the finished
     drinking water shall not exceed 2 mg/L.
[PY] Polyamines Certified by NSF International comply with 40 CFR 141.111 requirements for
     percent monomer and dose.

Aluminum Chlorohydrate/Polyaluminum Chloride[AL]
Trade Designation Product Function Max Use
Brennfloc 4000 Coagulation & Flocculation 250mg/L

[AL] Based on an evaluation of health effects data, the level of aluminum in the finished
     drinking water shall not exceed 2 mg/L.

Ammonium Hydroxide
Trade Designation Product Function Max Use
Ammonium Hydroxide 19% Chloramination 10mg/L

Ammonium Sulfate
Trade Designation Product Function Max Use
Ammonium Sulfate Chloramination 60mg/L
Ammonium Sulfate Solution Chloramination 60mg/L

Blended Corrosion Inhibitor
Trade Designation Product Function Max Use
Robin Phos PO-2 Sequestering
Corrosion & Scale Control
20mg/L

Blended Phosphates
Trade Designation Product Function Max Use
AquaPure 3637 Sequestering
Corrosion & Scale Control
25mg/L
AquaPure 3655 Sequestering
Corrosion & Scale Control
25mg/L
AquaPure 3673 Sequestering
Corrosion & Scale Control
25mg/L
AquaPure 3691 Sequestering
Corrosion & Scale Control
25mg/L
Robin Phos PO-73 Sequestering
Corrosion & Scale Control
25mg/L

Citric Acid
Trade Designation Product Function Max Use
Citric Acid 50%[1] [2] Membrane Cleaner NA
Citric Acid Solution[1] [2] Membrane Cleaner NA

[1] This product is designed to be used off-line and flushed out prior to using the system
    for drinking water, following manufacturer's use instructions.
[2] The pH of the influent and effluent water should be monitored to ensure that all traces
    of the product have been removed before placing into service.

Miscellaneous Chemical Products
Trade Designation Product Function Max Use
Brennfloc 4220[AL] Coagulation & Flocculation 250mg/L
Brennfloc 4420[AL] [PY] Coagulation & Flocculation 100mg/L
Brennfloc 4420H[AL] [PY] Coagulation & Flocculation 100mg/L
Robin 3000[PC] Coagulation & Flocculation 15mg/L
RobinFloc 1212[PC] Coagulation & Flocculation 15mg/L
Robinfloc 2000[PC] Coagulation & Flocculation 15mg/L

[AL] Based on an evaluation of health effects data, the level of aluminum in the finished
     drinking water shall not exceed 2 mg/L.
[PC] Polyacrylamide Products Certified by NSF International comply with 40 CFR 141.111
     requirements for percent monomer and dose.
[PY] Polyamines Certified by NSF International comply with 40 CFR 141.111 requirements for
     percent monomer and dose.

Miscellaneous Water Supply Products
Trade Designation Product Function Max Use
Citric Acid 30-50%[1] [2] Membrane Cleaner NA

[1] This product is designed to be used off-line and flushed out prior to using the system
    for drinking water, following manufacturer's use instructions.
[2] The pH of the influent and effluent water should be monitored to ensure that all traces
    of the product have been removed before placing into service.

Monosodium Orthophosphate
Trade Designation Product Function Max Use
AquaPure 3601 Sequestering
Corrosion & Scale Control
25mg/L

Poly (Diallyldimethylammonium Chloride)(pDADMAC)
Trade Designation Product Function Max Use
Brennfloc CP 7215P Coagulation & Flocculation 100mg/L
Robin 110 Coagulation & Flocculation 100mg/L
Robin 120 Coagulation & Flocculation 50mg/L
Robin 220 Coagulation & Flocculation 50mg/L
RobinFloc 4325 Coagulation & Flocculation 100mg/L
RobinFloc 4728 Coagulation & Flocculation 96mg/L

Polyaluminum Chloride[AL]
Trade Designation Product Function Max Use
Aluminum Chloride Hydroxide Aqueous Solution Coagulation & Flocculation 250mg/L
Aluminum Chlorohydrate Aqueous Solution Coagulation & Flocculation 250mg/L
Robin AC-100 Coagulation & Flocculation 250mg/L
RobinFloc 4708 Coagulation & Flocculation 250mg/L

[AL] Based on an evaluation of health effects data, the level of aluminum in the finished
     drinking water shall not exceed 2 mg/L.

Polymer Blends[AL]
Trade Designation Product Function Max Use
AC 2602 PA Coagulation & Flocculation 50mg/L
Brennfloc BC 4101 Coagulation & Flocculation 66mg/L
Polyaluminum Sulfate Coagulation & Flocculation 150mg/L
Polyaluminum Sulfate Polymer Emulsion Coagulation & Flocculation 150mg/L
Robin AC 110 Coagulation & Flocculation 130mg/L
Robin AC-3545 Coagulation & Flocculation 50mg/L
Robin AS-110 Coagulation & Flocculation 150mg/L
Robin AS-120 Coagulation & Flocculation 150mg/L
Robin AS-140 Coagulation & Flocculation 100mg/L
Robin FR-2003[PY] Coagulation & Flocculation 20mg/L
Robin Floc 4725 Coagulation & Flocculation 155mg/L
RobinFloc 4707[PY] Coagulation & Flocculation
Flocculant
100mg/L
RobinFloc 4714 Coagulation & Flocculation 238mg/L
RobinFloc 4715 Coagulation & Flocculation 156mg/L
RobinFloc 4740 Coagulation & Flocculation
Flocculant
68mg/L

[AL] Based on an evaluation of health effects data, the level of aluminum in the finished
     drinking water shall not exceed 2 mg/L.
[PY] Polyamines Certified by NSF International comply with 40 CFR 141.111 requirements for
     percent monomer and dose.

Sodium Permanganate[PO]
Trade Designation Product Function Max Use
Sodium Permanganate Oxidant 176mg/L
Sodium Permanganate 20% Oxidant 176mg/L
Sodium Permanganate 40% Oxidant 86mg/L
Sodium Permanganate Solution Oxidant 176mg/L
Sodium Permanganate Solution 15% Oxidant 235mg/L
Sodium Permanganate Solution 19% Oxidant 185mg/L

[PO] The finished drinking water shall be monitored to ensure that levels of manganese

     do not exceed 0.05 mg/L.

Sodium Polyphosphates, Glassy
Trade Designation Product Function Max Use
AquaPure SH 36 Corrosion Control 25mg/L
Robin Phos P-1 Corrosion Control
Sequestering
28mg/L
SHMP Corrosion Control
Sequestering
28mg/L
Sodium Hexametaphosphate Corrosion Control
Sequestering
28mg/L
Sodium Polyphosphate Corrosion Control
Sequestering
28mg/L
Sodium Polyphosphates Glassy Corrosion Control
Sequestering
28mg/L


Facility : Indianapolis, IN


Aluminum Chlorohydrate[AL]
Trade Designation Product Function Max Use
Prestofloc C-100 Coagulation & Flocculation 250mg/L

[AL] Based on an evaluation of health effects data, the level of aluminum in the finished
     drinking water shall not exceed 2 mg/L.

Aluminum Sulfate[AL]
Trade Designation Product Function Max Use
Aluminum Sulfate Solution Coagulation & Flocculation 150mg/L
Liquid Alum Coagulation & Flocculation 150mg/L
Liquid Alum 50% Sol Coagulation & Flocculation 150mg/L

[AL] Based on an evaluation of health effects data, the level of aluminum in the finished
     drinking water shall not exceed 2 mg/L.

Ammonium Sulfate
Trade Designation Product Function Max Use
Ammonium Sulfate 38.5% Sol Chloramination 60mg/L
Ammonium Sulfate 40% Chloramination 60mg/L
Ammonium Sulfate 40% Sol Chloramination 60mg/L
WWT 9710 Chloramination 60mg/L

Citric Acid[1] [2]
Trade Designation Product Function Max Use
Citric Acid Solution Membrane Cleaner NA
Citric Acid, Anhydrous Membrane Cleaner NA

[1] This product is designed to be used off-line and flushed out prior to using the system
    for drinking water, following the manufacturer's use instructions.
[2] The pH of the influent and effluent water should be monitored to ensure that all traces
    of the product have been removed before placing into service.

Hydrofluosilicic Acid
Trade Designation Product Function Max Use
Hydrofluosilicic Acid 23% Fluoridation 5 mg/L

Poly (Diallyldimethylammonium Chloride)(pDADMAC)
Trade Designation Product Function Max Use
Robin 110 Coagulation & Flocculation 100mg/L
Robin 120 Coagulation & Flocculation 50mg/L
Robin 220 Coagulation & Flocculation 50mg/L
RobinFloc 4325 Coagulation & Flocculation 100mg/L

Polyaluminum Chloride[AL]
Trade Designation Product Function Max Use
Brennfloc CC 2818 Coagulation & Flocculation 250mg/L
Brennfloc CC2358 Coagulation & Flocculation 100mg/L
Prestofloc C-100 Coagulation & Flocculation 250mg/L

[AL] Based on an evaluation of health effects data, the level of aluminum in the finished
     drinking water shall not exceed 2 mg/L.

Sodium Hydroxide[3]
Trade Designation Product Function Max Use
Caustic Soda 10% Corrosion & Scale Control
pH Adjustment
500mg/L
Caustic Soda 20% Corrosion & Scale Control
pH Adjustment
250mg/L
Caustic Soda 25% pH Adjustment
Corrosion & Scale Control
200mg/L
Caustic Soda 30% Corrosion & Scale Control
pH Adjustment
166mg/L
Caustic Soda 50% pH Adjustment
Corrosion & Scale Control
100mg/L
Sodium Hydroxide 10% Corrosion & Scale Control
pH Adjustment
500mg/L
Sodium Hydroxide 20% Corrosion & Scale Control
pH Adjustment
250mg/L
Sodium Hydroxide 25% Corrosion & Scale Control
pH Adjustment
200mg/L
Sodium Hydroxide 30% Corrosion & Scale Control
pH Adjustment
166mg/L
Sodium Hydroxide 50% Corrosion & Scale Control
pH Adjustment
100mg/L

[3] Trade Designation may be followed by a three digit alpha suffix to designate the
    chlor-alkali electrolytic cell category/grade.

Sodium Hypochlorite[HY]
Trade Designation Product Function Max Use
Chem Bleach Household Disinfection & Oxidation 164mg/L
SNO-GLO BLEACH Disinfection & Oxidation 86mg/L
Sno-Glo Bleach Disinfection & Oxidation 86mg/L
Sodium Hypochlorite 10% Disinfection & Oxidation 86mg/L
Sodium Hypochlorite 12.5% Disinfection & Oxidation 69mg/L
Sodium Hypochlorite 5.25% Solution Disinfection & Oxidation 164mg/L

[HY] The residual levels of chlorine (hypochlorite ion and hypochlorous acid), chlorine
     dioxide, chlorate ion, chloramine and disinfection by-products shall be monitored in the
     finished drinking water to ensure compliance to all applicable regulations. Also,
     reference the AWWA B300 (Hypochlorites) standard's Recommendations for the Handling and
     Storage of Hypochlorite Solutions appendix for information on preservation techniques
     for hypochlorite bleach in transit and storage.

Sulfuric Acid
Trade Designation Product Function Max Use
Sulfuric Acid Corrosion & Scale Control
pH Adjustment
50mg/L
Sulfuric Acid 50% Corrosion & Scale Control
pH Adjustment
93mg/L
Sulfuric Acid 66 BE Corrosion & Scale Control
pH Adjustment
50mg/L
Sulfuric Acid 66 Degree Corrosion & Scale Control
pH Adjustment
50mg/L

NOTE: Only products bearing the NSF Mark on the product, packing, and/or documentation shipped
      with the product are Certified.

Facility : Terre Haute, IN


Chlorine[CL]
Trade Designation Product Function Max Use
Chlorine Disinfection & Oxidation 30 mg/L

[CL] The residual levels of chlorine (hypochlorite ion and hypochlorous acid), chlorine
     dioxide, chlorate ion, chloramine and disinfection by-products shall be monitored in the
     finished drinking water to ensure compliance to all applicable regulations.

Sodium Hydroxide[1]
Trade Designation Product Function Max Use
Caustic Soda 10% Corrosion & Scale Control
pH Adjustment
500mg/L
Caustic Soda 20% Corrosion & Scale Control
pH Adjustment
250mg/L
Caustic Soda 25% Corrosion & Scale Control
pH Adjustment
200mg/L
Caustic Soda 30% Corrosion & Scale Control
pH Adjustment
166mg/L
Caustic Soda 50% Corrosion & Scale Control
pH Adjustment
100mg/L
Sodium Hydroxide 10% Corrosion & Scale Control
pH Adjustment
500mg/L
Sodium Hydroxide 20% Corrosion & Scale Control
pH Adjustment
250mg/L
Sodium Hydroxide 25% Corrosion & Scale Control
pH Adjustment
200mg/L
Sodium Hydroxide 30% Corrosion & Scale Control
pH Adjustment
166mg/L
Sodium Hydroxide 50% Corrosion & Scale Control
pH Adjustment
100mg/L

[1] Trade Designation may be followed by a three digit alpha suffix to designate the
    chlor-alkali electrolytic cell category/grade.

Sodium Hypochlorite[HY]
Trade Designation Product Function Max Use
Chem Bleach Household Disinfection & Oxidation 200mg/L
SNO-GLO BLEACH Disinfection & Oxidation 105mg/L
Sno-Glo Bleach Disinfection & Oxidation 105mg/L
Sodium Hypochlorite 10% Disinfection & Oxidation 105mg/L
Sodium Hypochlorite 12.5% Disinfection & Oxidation 84 mg/L
Sodium Hypochlorite 5.25% Solution Disinfection & Oxidation 200mg/L

[HY] The residual levels of chlorine (hypochlorite ion and hypochlorous acid), chlorine
     dioxide, chlorate ion, chloramine and disinfection by-products shall be monitored in the
     finished drinking water to ensure compliance to all applicable regulations. Also,
     reference the AWWA B300 (Hypochlorites) standard's Recommendations for the Handling and
     Storage of Hypochlorite Solutions appendix for information on preservation techniques
     for hypochlorite bleach in transit and storage.

NOTE: Only products bearing the NSF Mark on the product, packing, and/or documentation shipped
      with the product are Certified.

Facility : Georgetown, KY


Sodium Hypochlorite[HY]
Trade Designation Product Function Max Use
Sodium Hypochlorite Disinfection & Oxidation 64mg/L

[HY] The residual levels of chlorine (hypochlorite ion and hypochlorous acid), chlorine
     dioxide, chlorate ion, chloramine and disinfection by-products shall be monitored in the
     finished drinking water to ensure compliance to all applicable regulations. Also,
     reference the AWWA B300 (Hypochlorites) standard's Recommendations for the Handling and
     Storage of Hypochlorite Solutions appendix for information on preservation techniques
     for hypochlorite bleach in transit and storage.


Facility : Henderson, KY


Aluminum Chlorohydrate[AL]
Trade Designation Product Function Max Use
Brennfloc BC4105[PY] Coagulation & Flocculation 31mg/L
Prestofloc C-100 Coagulation & Flocculation 250 mg/L

[AL] Based on an evaluation of health effects data, the level of aluminum in the finished
     drinking water shall not exceed 2 mg/L.
[PY] Polyamines Certified by NSF International comply with 40 CFR 141.111 requirements for
     percent monomer and dose.

Aluminum Sulfate[AL]
Trade Designation Product Function Max Use
Aluminum Sulfate 50% Coagulation & Flocculation 150mg/L
Aluminum Sulfate 50% Solution Coagulation & Flocculation 150mg/L
Aluminum Sulfate Solution Coagulation & Flocculation 150 mg/L
Liquid Alum Coagulation & Flocculation 150 mg/L

[AL] Based on an evaluation of health effects data, the level of aluminum in the finished
     drinking water shall not exceed 2 mg/L.

Ammonia, Anhydrous
Trade Designation Product Function Max Use
Ammonia, Anhydrous Chloramination 5 mg/L

Ammonium Hydroxide
Trade Designation Product Function Max Use
AQUA AMMONIA Chloramination 10 mg/L
Ammonium Hydroxide 19% Chloramination 10mg/L
Aqua Ammonia 26 Deg Chloramination 10mg/L

Ammonium Sulfate
Trade Designation Product Function Max Use
Ammonium Sulfate 38.5% Sol Chloramination 60mg/L
Ammonium Sulfate 40% Chloramination 60mg/L
Ammonium Sulfate 40% Sol Chloramination 60mg/L
WWT 9710 Chloramination 60mg/L

Blended Phosphates
Trade Designation Product Function Max Use
AquaPure 3627 Corrosion & Scale Control
Sequestering
25mg/L
AquaPure 3628 Corrosion & Scale Control
Sequestering
25mg/L
AquaPure 3637 Corrosion & Scale Control
Sequestering
25mg/L
AquaPure 3646 Corrosion & Scale Control
Sequestering
25mg/L
AquaPure 3664 Corrosion & Scale Control
Sequestering
25mg/L
AquaPure 3672 Corrosion & Scale Control
Sequestering
25mg/l
AquaPure 3673 Corrosion & Scale Control
Sequestering
25mg/L
AquaPure 3682 Corrosion & Scale Control
Sequestering
25mg/l
AquaPure 3691 Corrosion & Scale Control
Sequestering
25mg/L
Aquapure 3610 Corrosion & Scale Control
Sequestering
25mg/L
Aquapure 3619 Corrosion & Scale Control
Sequestering
25mg/L
Aquapure 3655 Corrosion & Scale Control
Sequestering
25mg/L

Chlorine[CL]
Trade Designation Product Function Max Use
Chlorine, Liquified Gas Disinfection & Oxidation 30 mg/L

[CL] The residual levels of chlorine (hypochlorite ion and hypochlorous acid), chlorine
     dioxide, chlorate ion, chloramine and disinfection by-products shall be monitored in the
     finished drinking water to ensure compliance to all applicable regulations.

Citric Acid[1]
Trade Designation Product Function Max Use
Citric Acid 50% Membrane Cleaner NA
Citric Acid Solution Membrane Cleaner NA

[1] These products are designed to be used off-line and flushed out prior to using the
    system for drinking water, following manufacturer's use instructions.  The pH of the
    influent and effluent water should be monitored to ensure that all traces of the product
    have been removed before placing into service.

Ferric Chloride
Trade Designation Product Function Max Use
Ferric Chloride 38-42% Coagulation & Flocculation 250mg/L
Ferric Chloride Liquid Coagulation & Flocculation 250 mg/L
Ferric Chloride Solution Coagulation & Flocculation 250 mg/L
Iron (III) Chloride Solution Coagulation & Flocculation 250mg/L
Iron Trichloride Solution Coagulation & Flocculation 250mg/L

Ferric Sulfate
Trade Designation Product Function Max Use
Ferri-Floc Liquid Coagulation & Flocculation 500 mg/L
Ferric Sulfate Coagulation & Flocculation 500 mg/L

Fluosilicic Acid
Trade Designation Product Function Max Use
Hydrofluosilicic Acid 23% Fluoridation 5 mg/L

Hydrochloric Acid
Trade Designation Product Function Max Use
Hydrochloric Acid 15% Corrosion & Scale Control
pH Adjustment
80mg/L
Hydrochloric Acid 20 BE Corrosion & Scale Control 44mg/L
Hydrochloric Acid 20 BE / 31.45 Corrosion & Scale Control 44mg/L
Hydrochloric Acid 28% Corrosion & Scale Control 50mg/L
Hydrochloric Acid 31.45% Corrosion & Scale Control 44mg/L
Hydrochloric Acid 32% Corrosion & Scale Control 44mg/L
Muriatic Acid Corrosion & Scale Control 44mg/L
Muriatic Acid 10% Corrosion & Scale Control 138mg/L
Muriatic Acid 15% Corrosion & Scale Control
pH Adjustment
80mg/L
Muriatic Acid 20 DEG BE Corrosion & Scale Control 44mg/L
Muriatic Acid 22 DEG BE Corrosion & Scale Control 40mg/L

Hydrogen Peroxide [HP]
Trade Designation Product Function Max Use
Hydrogen Peroxide 30%[2] Oxidant 3.5mg/L
Hydrogen Peroxide 32%[3] Oxidant 3.3mg/L
Hydrogen Peroxide 35%[4] Oxidant 3 mg/L
Hydrogen Peroxide 8% Oxidant 13mg/L

[2] This product may be used at a maximum use level of 95 mg/L for the following functions:
    - reoxygenation of treated water
    - oxidation of organic residuals
    - oxidation of any reduced products, such as Fe(II) and sulfides
    Treatment must be followed by chlorination to a chlorine residual no to exceed 4 mg/L,
    the EPA's proposed maximum residual level.
[3] This product may be used at a maximum use level of 90 mg/L for the following functions:
    - reoxygenation of treated water
    - oxidation of organic residuals
    - oxidation of any reduced products, such as Fe(II) and sulfides
    Treatment must be followed by chlorination to a chlorine residual no to exceed 4 mg/L,
    the EPA's proposed maximum residual level.
[4] This product may be used at a maximum use level of 85 mg/L for the following functions:
    - reoxygenation of treated water
    - oxidation of organic residuals
    - oxidation of any reduced products, such as Fe(II) and sulfides
    Treatment must be followed by chlorination to a chlorine residual no to exceed 4 mg/L,
    the EPA's proposed maximum residual level.
[HP] Use of this product shall be followed by chlorination to remove levels of hydrogen
     peroxide.  Chlorine residuals shall not exceed 4 mg/L, the EPA's proposed maximum
     residual level.

Miscellaneous Water Supply Products[5] [6]
Trade Designation Product Function Max Use
Innova Well Cleaning Aid NA
Layne RC Well Cleaning Aid N/A
Layne RC10 Well Cleaning Aid N/A
Layne RC15 Well Cleaning Aid N/A

[5] These products are designed to be used off-line and flushed out prior to using the
    system for drinking water, following manufacturer's use instructions.
[6] The well is to be properly flushed and drained before being places in service.

Monosodium Orthophosphate
Trade Designation Product Function Max Use
AquaPure 3601 Corrosion & Scale Control
Sequestering
25mg/L

Phosphoric Acid
Trade Designation Product Function Max Use
Aquapure Ortho Corrosion & Scale Control 26mg/L
Phosphoric Acid (36% PO4) Corrosion & Scale Control 26mg/L
Phosphoric Acid 75% Corrosion & Scale Control 13mg/L

Polyaluminum Chloride[AL]
Trade Designation Product Function Max Use
Brennfloc BC 2380 Coagulation & Flocculation 200mg/L
Brennfloc BC 2381 Coagulation & Flocculation 200mg/L
Brennfloc CC 2818 Coagulation & Flocculation 250mg/L
Brennfloc CC2358 Coagulation & Flocculation 100mg/L
Prestofloc C-50 Coagulation & Flocculation 250 mg/L

[AL] Based on an evaluation of health effects data, the level of aluminum in the finished
     drinking water shall not exceed 2 mg/L.

Polyamines[PY]
Trade Designation Product Function Max Use
Brennfloc CP 7452P Coagulation & Flocculation 20mg/L

[PY] Polyamines Certified by NSF International comply with 40 CFR 141.111 requirements for
     percent monomer and dose.

Polymer Blends[AL] [PY]
Trade Designation Product Function Max Use
Brennfloc BC 2376 Coagulation & Flocculation 250mg/L

[AL] Based on an evaluation of health effects data, the level of aluminum in the finished
     drinking water shall not exceed 2 mg/L.
[PY] Polyamines Certified by NSF International comply with 40 CFR 141.111 requirements for
     percent monomer and dose.

Sodium Bisulfite[7]
Trade Designation Product Function Max Use
Sodium Bisulfite 19-44% Dechlorinator & Antioxidant 46mg/L

[7] This product contains sulfite. Sulfites have been known to cause potentially lethal
    allergic reactions in sulfite-sensitive individuals. The maximum recommended allowable
    residual sulfite level in the finished drinking water is 100 ppb (0.1 mg/L).

Sodium Carbonate
Trade Designation Product Function Max Use
Soda Ash 15% Corrosion & Scale Control
pH Adjustment
667mg/L
Sodium Carbonate 15% Corrosion & Scale Control
pH Adjustment
667mg/L

Sodium Chlorite[8] [CL]
Trade Designation Product Function Max Use
Sodium Chlorite Chlorine Dioxide Production 14mg/L
Sodium Chlorite 31.25% Chlorine Dioxide Production 22mg/L

[8] These products are certified for use in chlorine dioxide generation.
[CL] The residual levels of chlorine (hypochlorite ion and hypochlorous acid), chlorine
     dioxide, chlorate ion, chloramine and disinfection by-products shall be monitored in the
     finished drinking water to ensure compliance to all applicable regulations.

Sodium Hydroxide[9]
Trade Designation Product Function Max Use
Caustic Soda 20% Corrosion & Scale Control 250 mg/L
Caustic Soda 25% Corrosion & Scale Control 200 mg/L
Caustic Soda 50% Corrosion & Scale Control 100 mg/L
Caustic Sodia 30% Corrosion & Scale Control 166mg/L
Sodium Hydroxide 20% Corrosion & Scale Control 250mg/L
Sodium Hydroxide 25% Corrosion & Scale Control 200mg/L
Sodium Hydroxide 30% Corrosion & Scale Control 166mg/L
Sodium Hydroxide 50% Corrosion & Scale Control 100mg/L

[9] Trade designation may be followed by a three digit alpha suffix to designate the
    chlor-alkali electrolytic cell category/grade.

Sodium Hypochlorite[HY]
Trade Designation Product Function Max Use
Chem Bleach Household Disinfection & Oxidation 200mg/L
SNO-GLO BLEACH Disinfection & Oxidation 105mg/L
Sno-Glo 10% Bleach Disinfection & Oxidation 105 mg/L
Sodium Hypochlorite 10% Disinfection & Oxidation 105 mg/L
Sodium Hypochlorite 12.5% Disinfection & Oxidation 84 mg/L
Sodium Hypochlorite 12.5% NSF Disinfection & Oxidation 84mg/L
Sodium Hypochlorite 5.25% Solution Disinfection & Oxidation 200mg/L

[HY] The residual levels of chlorine (hypochlorite ion and hypochlorous acid), chlorine
     dioxide, chlorate ion, chloramine and disinfection by-products shall be monitored in the
     finished drinking water to ensure compliance to all applicable regulations. Also,
     reference the AWWA B300 (Hypochlorites) standard's Recommendations for the Handling and
     Storage of Hypochlorite Solutions appendix for information on preservation techniques
     for hypochlorite bleach in transit and storage.

Sodium Permanganate[PO]
Trade Designation Product Function Max Use
Sodium Permanganate Oxidant 176mg/L
Sodium Permanganate 20% Oxidant 176mg/L
Sodium Permanganate 40% Oxidant 88mg/L
Sodium Permanganate Solution Oxidant 176mg/L
Sodium Permanganate Solution 15% Oxidant 235mg/L
Sodium Permanganate Solution 19% Oxidant 185mg/L

[PO] The finished drinking water shall be monitored to ensure that levels of manganese

     do not exceed 0.05 mg/L.

Sodium Polyphosphates, Glassy
Trade Designation Product Function Max Use
AquaPure SH 36 Corrosion & Scale Control 25mg/L

Sodium Silicate
Trade Designation Product Function Max Use
N Sodium Silicate Solution Corrosion & Scale Control 42mg/L

Sulfuric Acid
Trade Designation Product Function Max Use
Sulfuric Acid 35% Corrosion & Scale Control 133mg/L
Sulfuric Acid 38.5% Corrosion & Scale Control 121mg/L
Sulfuric Acid 50% Corrosion & Scale Control 93mg/L
Sulfuric Acid 78% Corrosion & Scale Control 60mg/L
Sulfuric Acid 93% Corrosion & Scale Control 50mg/L

Tetrapotassium Pyrophosphate
Trade Designation Product Function Max Use
Tetrapotassium Pyrophosphate 60% Solution Corrosion & Scale Control
Sequestering
29mg/L

[CP] The finished drinking water shall be monitored to ensure that levels of copper do not
     exceed 1.3 mg/L.

Facility : Louisville, KY


Sodium Hypochlorite[HY]
Trade Designation Product Function Max Use
Sodium Hypochlorite 12.5% Disinfection & Oxidation 84mg/L

[HY] The residual levels of chlorine (hypochlorite ion and hypochlorous acid), chlorine
     dioxide, chlorate ion, chloramine and disinfection by-products shall be monitored in the
     finished drinking water to ensure compliance to all applicable regulations. Also,
     reference the AWWA B300 (Hypochlorites) standard's Recommendations for the Handling and
     Storage of Hypochlorite Solutions appendix for information on preservation techniques
     for hypochlorite bleach in transit and storage.


Facility : Charlotte, NC


Hydrochloric Acid
Trade Designation Product Function Max Use
Hydrochloric Acid 15% pH Adjustment
Corrosion & Scale Control
80mg/L
Hydrochloric Acid 20 BE Corrosion & Scale Control 44mg/L
Hydrochloric Acid 20 BE / 31.45 Corrosion & Scale Control 44mg/L
Hydrochloric Acid 28% Corrosion & Scale Control 50mg/L
Hydrochloric Acid 31.45% Corrosion & Scale Control 44mg/L
Hydrochloric Acid 32% Corrosion & Scale Control 44mg/L
Muriatic Acid Corrosion & Scale Control 44mg/L
Muriatic Acid 10% Corrosion & Scale Control 138mg/L
Muriatic Acid 15% pH Adjustment
Corrosion & Scale Control
80mg/L
Muriatic Acid 20 DEG BE Corrosion & Scale Control 44mg/L
Muriatic Acid 22 DEG BE Corrosion & Scale Control 40mg/L

Sodium Hydroxide[1]
Trade Designation Product Function Max Use
Caustic Soda 20% Corrosion & Scale Control 250mg/L
Caustic Soda 25% Corrosion & Scale Control 200mg/L
Caustic Soda 30% Corrosion & Scale Control 166mg/L
Caustic Soda 50% Corrosion & Scale Control 100mg/L
Sodium Hydroxide 20% Corrosion & Scale Control 250mg/L
Sodium Hydroxide 25% Corrosion & Scale Control 200mg/L
Sodium Hydroxide 30% Corrosion & Scale Control 166mg/L
Sodium Hydroxide 50% Corrosion & Scale Control 100mg/L

[1] Trade designation may be followed by a three digit alpha suffix to designate the
    chlor-alkali electrolytic cell category/grade.

Sodium Hypochlorite[HY]
Trade Designation Product Function Max Use
Sodium Hypochlorite 12.5% Disinfection & Oxidation 84mg/L

[HY] The residual levels of chlorine (hypochlorite ion and hypochlorous acid), chlorine
     dioxide, chlorate ion, chloramine and disinfection by-products shall be monitored in the
     finished drinking water to ensure compliance to all applicable regulations. Also,
     reference the AWWA B300 (Hypochlorites) standard's Recommendations for the Handling and
     Storage of Hypochlorite Solutions appendix for information on preservation techniques
     for hypochlorite bleach in transit and storage.

Sulfuric Acid
Trade Designation Product Function Max Use
Sulfuric Acid Corrosion & Scale Control
pH Adjustment
50mg/L
Sulfuric Acid 15% Corrosion & Scale Control
pH Adjustment
260mg/L
Sulfuric Acid 38.5% Corrosion & Scale Control
pH Adjustment
120mg/L
Sulfuric Acid 50% Corrosion & Scale Control
pH Adjustment
93mg/L
Sulfuric Acid 66 BE Corrosion & Scale Control
pH Adjustment
50mg/L
Sulfuric Acid 66 DEG Corrosion & Scale Control
pH Adjustment
50mg/L
Sulfuric Acid 78% Corrosion & Scale Control
pH Adjustment
60mg/L
Sulfuric Acid 93% Corrosion & Scale Control
pH Adjustment
50mg/L

[PY] Polyamines Certified by NSF International comply with 40 CFR 141.111 requirements for
     percent monomer and dose.

Facility : Durham, NC


Ammonium Sulfate
Trade Designation Product Function Max Use
Ammonium Sulfate 38.5% Sol Chloramination 60mg/L
Ammonium Sulfate 40% Chloramination 60mg/L
Ammonium Sulfate 40% Sol Chloramination 60mg/L
WWT 9710 Chloramination 60mg/L

Sodium Hydroxide
Trade Designation Product Function Max Use
Caustic Soda 10% Corrosion & Scale Control
pH Adjustment
500mg/L
Caustic Soda 20% Corrosion & Scale Control
pH Adjustment
250mg/L
Caustic Soda 25% Corrosion & Scale Control
pH Adjustment
200mg/L
Caustic Soda 30% Corrosion & Scale Control
pH Adjustment
166mg/L
Caustic Soda 50% Corrosion & Scale Control
pH Adjustment
100mg/L
Sodium Hydroxide 10% Corrosion & Scale Control
pH Adjustment
500mg/L
Sodium Hydroxide 20% Corrosion & Scale Control
pH Adjustment
250mg/L
Sodium Hydroxide 25% Corrosion & Scale Control
pH Adjustment
200mg/L
Sodium Hydroxide 30% Corrosion & Scale Control
pH Adjustment
166mg/L
Sodium Hydroxide 50% Corrosion & Scale Control
pH Adjustment
100mg/L


Facility : Greensboro, NC


Hydrogen Peroxide[HP]
Trade Designation Product Function Max Use
Hydrogen Peroxide 30% Disinfection & Oxidation 3.5mg/L
Hydrogen Peroxide 32% Disinfection & Oxidation 3.3mg/L
Hydrogen Peroxide 35% Disinfection & Oxidation 3mg/L
Hydrogen Peroxide 50% Disinfection & Oxidation 2.1mg/L
Hydrogen Peroxide 8% Disinfection & Oxidation 13mg/L

[HP] Use of this product shall be followed by chlorination to remove levels of hydrogen
     peroxide.  Chlorine residuals shall not exceed 4 mg/L, the EPA's proposed maximum
     residual level.

Miscellaneous Corrosion Chemicals[1]
Trade Designation Product Function Max Use
Aquapure ® ZOP 1237 Corrosion & Scale Control 15mg/L

[1] Based on an evaluation of health effects data, the level of zinc in the finished
    drinking water should not exceed 2.0 mg/L.

Sodium Hydroxide
Trade Designation Product Function Max Use
Caustic Soda 10% Corrosion & Scale Control
pH Adjustment
500mg/L
Caustic Soda 20% Corrosion & Scale Control
pH Adjustment
250mg/L
Caustic Soda 25% Corrosion & Scale Control
pH Adjustment
200mg/L
Caustic Soda 30% Corrosion & Scale Control
pH Adjustment
166mg/L
Caustic Soda 50% Corrosion & Scale Control
pH Adjustment
100mg/L
Sodium Hydroxide 10% Corrosion & Scale Control
pH Adjustment
500mg/L
Sodium Hydroxide 20% Corrosion & Scale Control
pH Adjustment
250mg/L
Sodium Hydroxide 25% Corrosion & Scale Control
pH Adjustment
200mg/L
Sodium Hydroxide 30% Corrosion & Scale Control
pH Adjustment
166mg/L
Sodium Hydroxide 50% Corrosion & Scale Control
pH Adjustment
100mg/L


Facility : Wilmington, NC


Sodium Hydroxide
Trade Designation Product Function Max Use
Caustic Soda 25% pH Adjustment 200mg/L
Caustic Soda 50% pH Adjustment 100mg/L
Sodium Hydroxide 25% pH Adjustment 200mg/L
Sodium Hydroxide 50% pH Adjustment 100mg/L

NOTE: Only products bearing the NSF Mark on the product, packing, and/or documentation shipped
      with the product are Certified.

Facility : Charleston, SC


Ammonium Hydroxide
Trade Designation Product Function Max Use
Ammonium Hydroxide 19% Chloramination 10mg/L

Sodium Hydroxide[1]
Trade Designation Product Function Max Use
Caustic Soda 50% Corrosion & Scale Control
pH Adjustment
100mg/L

[1] Trade designation may be followed by a three digit alpha suffix to designate the
    chlor-alkali electrolytic cell category/grade.

NOTE: Only products bearing the NSF Mark on the product, product packaging, and/or
      documentation shipped with the product are Certified.

Facility : Chattanooga, TN


Aluminum Sulfate[AL]
Trade Designation Product Function Max Use
Aluminum Sulfate Solution Coagulation & Flocculation 150 mg/L
Liquid Alum Coagulation & Flocculation 150 mg/L

[AL] Based on an evaluation of health effects data, the level of aluminum in the finished
     drinking water shall not exceed 2 mg/L.

Chlorine[CL]
Trade Designation Product Function Max Use
Chlorine, Liquified Gas Disinfection & Oxidation 30 mg/L

[CL] The residual levels of chlorine (hypochlorite ion and hypochlorous acid), chlorine
     dioxide, chlorate ion, chloramine and disinfection by-products shall be monitored in the
     finished drinking water to ensure compliance to all applicable regulations.

Citric Acid[1]
Trade Designation Product Function Max Use
Citric Acid 50% Membrane Cleaner NA
Citric Acid Solution Membrane Cleaner NA

[1] This product is designed to be used off-line and flushed prior to using the system for
    drinking water, following manufacturer's use
    instructions.  The pH of the influent and effluent water should be monitored to ensure
    that all traces of the product have been removed before placing into service.

Ferric Chloride
Trade Designation Product Function Max Use
Ferric Chloride 38-42% Coagulation & Flocculation 250mg/L
Ferric Chloride Liquid Coagulation & Flocculation 250 mg/L
Ferric Chloride Solution Coagulation & Flocculation 250 mg/L
Iron (III) Chloride Solution Coagulation & Flocculation 250mg/L
Iron Trichloride Solution Coagulation & Flocculation 250mg/L

Ferric Sulfate
Trade Designation Product Function Max Use
Ferri-Floc Liquid Coagulation & Flocculation 500 mg/L
Ferric Sulfate Coagulation & Flocculation 500 mg/L

Fluosilicic Acid
Trade Designation Product Function Max Use
Hydrofluosilicic Acid 23% Fluoridation 5mg/L

Hydrochloric Acid
Trade Designation Product Function Max Use
Hydrochloric Acid 20 BE Corrosion & Scale Control 44mg/L
Hydrochloric Acid 20 BE / 31.45 Corrosion & Scale Control 44mg/L
Hydrochloric Acid 28% Corrosion & Scale Control 50mg/L
Hydrochloric Acid 31.45% Corrosion & Scale Control 44mg/L
Hydrochloric Acid 32% Corrosion & Scale Control 44mg/L
Muriatic Acid Corrosion & Scale Control 44mg/L
Muriatic Acid 10% Corrosion & Scale Control 138mg/L
Muriatic Acid 20 DEG BE Corrosion & Scale Control 44mg/L
Muriatic Acid 22 DEG BE Corrosion & Scale Control 40mg/L

Hydrogen Peroxide [HP]
Trade Designation Product Function Max Use
Hydrogen Peroxide 30%[2] Oxidant 3.5mg/L
Hydrogen Peroxide 32%[3] Oxidant 3.3mg/L
Hydrogen Peroxide 50%[4] Oxidant 2.1mg/L
Hydrogen Peroxide 8% Oxidant 13mg/L
Hydrogen peroxide 35% Oxidant 3mg/L

[2] This product may be used at a maximum use level of 95 mg/L for the following functions:
    - reoxygenation of treated water
    - oxidation of organic residuals
    - oxidation of any reduced products, such as Fe(II) and sulfides
    Treatment must be followed by chlorination to a chlorine residual no to exceed 4 mg/L,
    the EPA's proposed maximum residual level.
[3] This product may be used at a maximum use level of 90 mg/L for the following functions:
    - reoxygenation of treated water
    - oxidation of organic residuals
    - oxidation of any reduced products, such as Fe(II) and sulfides
    Treatment must be followed by chlorination to a chlorine residual no to exceed 4 mg/L,
    the EPA's proposed maximum residual level.
[4] This product may be used at a maximum use level of 60 mg/L for the following functions:
     - reoxygenation of treated water
     - oxidation of organic residuals
     - oxidation of any reduced products, such as Fe(II) and sulfides
     Treatment must be followed by chlorination to a chlorine residual no to exceed 4 mg/L,
    the EPA's proposed maximum residual level.
[HP] Use of this product shall be followed by chlorination to remove levels of hydrogen
     peroxide.  Chlorine residuals shall not exceed 4 mg/L, the EPA's proposed maximum
     residual level.

Polyaluminum Chloride[AL]
Trade Designation Product Function Max Use
Brennfloc BC 2380 Coagulation & Flocculation 250mg/L

[AL] Based on an evaluation of health effects data, the level of aluminum in the finished
     drinking water shall not exceed 2 mg/L.

Polymer Blends[PY]
Trade Designation Product Function Max Use
ICS 7191 Coagulation & Flocculation 258mg/L
ICS 7201 Coagulation & Flocculation 490mg/L

[PY] Polyamines Certified by NSF International comply with 40 CFR 141.111 requirements for
     percent monomer and dose.

Sodium Bisulfite[5]
Trade Designation Product Function Max Use
Sodium Bisulfite 19-44% Dechlorinator & Antioxidant 46mg/L
Sodium Hydrogen Sulfite 40% Dechlorinator & Antioxidant 46mg/L

[5] This product contains sulfite. Sulfites have been known to cause potentially lethal
    allergic reactions in sulfite-sensitive individuals. The maximum recommended allowable
    residual sulfite level in the finished drinking water is 100 ppb (0.1 mg/L).

Sodium Hydroxide[6]
Trade Designation Product Function Max Use
Caustic Soda 20% Corrosion & Scale Control 250 mg/L
Caustic Soda 25% Corrosion & Scale Control 200 mg/L
Caustic Soda 50% Corrosion & Scale Control 100 mg/L
Sodium Hydroxide 20% Corrosion & Scale Control 250mg/L
Sodium Hydroxide 25% Corrosion & Scale Control 200mg/L
Sodium Hydroxide 50% Corrosion & Scale Control 100mg/L

[6] Trade designation may be followed by a three digit alpha suffix to designate the
    chlor-alkali electrolytic cell category/grade.

Sodium Hypochlorite[HY]
Trade Designation Product Function Max Use
Chem Bleach Household Disinfection & Oxidation 200mg/L
SNO-GLO BLEACH Disinfection & Oxidation 105mg/L
Sno-Glo 10% Bleach Disinfection & Oxidation 105 mg/L
Sodium Hypochlorite 12.5% Disinfection & Oxidation 84 mg/L
Sodium Hypochlorite 5.25% Solution Disinfection & Oxidation 200mg/L
Sodium Hypochlorite, 10% Disinfection & Oxidation 105 mg/L

[HY] The residual levels of chlorine (hypochlorite ion and hypochlorous acid), chlorine
     dioxide, chlorate ion, chloramine and disinfection by-products shall be monitored in the
     finished drinking water to ensure compliance to all applicable regulations. Also,
     reference the AWWA B300 (Hypochlorites) standard's Recommendations for the Handling and
     Storage of Hypochlorite Solutions appendix for information on preservation techniques
     for hypochlorite bleach in transit and storage.


Facility : Distribution Center - Chattanooga, TN


Sodium Hydroxide[1]
Trade Designation Product Function Max Use
Caustic Soda 50% Corrosion & Scale Control 100mg/L
Sodium Hydroxide 50% Corrosion & Scale Control 100mg/L
Sodium Hydroxide 55% Corrosion & Scale Control 100mg/L

[1] Trade designation may be followed by a three digit alpha suffix to designate the
    chlor-alkali electrolytic cell category/grade.


Facility : Memphis, TN


Sodium Hydroxide[1]
Trade Designation Product Function Max Use
Caustic Soda 20% Corrosion & Scale Control 250mg/L
Caustic Soda 25% Corrosion & Scale Control 200mg/L
Caustic Soda 50% Corrosion & Scale Control 100mg/L
Sodium Hydroxide 20% Corrosion & Scale Control 250mg/L
Sodium Hydroxide 25% Corrosion & Scale Control 200mg/L
Sodium Hydroxide 50% Corrosion & Scale Control 100mg/L

[1] Trade designation may be followed by a three digit alpha suffix to designate the
    chlor-alkali electrolytic cell category/grade.

Sodium Hypochlorite[HY]
Trade Designation Product Function Max Use
Sodium Hypochlorite 12.5% Disinfection & Oxidation 40mg/L

[HY] The residual levels of chlorine (hypochlorite ion and hypochlorous acid), chlorine
     dioxide, chlorate ion, chloramine and disinfection by-products shall be monitored in the
     finished drinking water to ensure compliance to all applicable regulations. Also,
     reference the AWWA B300 (Hypochlorites) standard's Recommendations for the Handling and
     Storage of Hypochlorite Solutions appendix for information on preservation techniques
     for hypochlorite bleach in transit and storage.

Sulfuric Acid
Trade Designation Product Function Max Use
Sulfuric Acid 35% Corrosion & Scale Control 133mg/L
Sulfuric Acid 38.5% Corrosion & Scale Control 121mg/L
Sulfuric Acid 50% Corrosion & Scale Control 93mg/L
Sulfuric Acid 66 BE Corrosion & Scale Control
pH Adjustment
50mg/L
Sulfuric Acid 66 DEG Corrosion & Scale Control
pH Adjustment
50mg/L
Sulfuric Acid 78% Corrosion & Scale Control 60mg/L
Sulfuric Acid 93% Corrosion & Scale Control 50mg/L

NOTE: Only products bearing the NSF Mark on the product, product packaging, and/or
      documentation shipped with the product are Certified.

Facility : Richmond, VA


Sodium Hydroxide[1]
Trade Designation Product Function Max Use
Caustic Soda 25% Corrosion & Scale Control 200mg/L
Caustic Soda 50% Corrosion & Scale Control 100mg/L
Sodium Hydroxide 25% Corrosion & Scale Control 200mg/L
Sodium Hydroxide 50% DIA Corrosion & Scale Control 100mg/L
Sodium Hydroxide 50% MEM Corrosion & Scale Control 100mg/L
Sodium Hydroxide Solution 50% Corrosion & Scale Control 100mg/L

[1] Trade designation may be followed by a three digit alpha suffix to designate the
    chlor-alkali electrolytic cell category/grade.

Sodium Hypochlorite[HY]
Trade Designation Product Function Max Use
Sodium Hypochlorite 12.5% Disinfection & Oxidation 79mg/L

[HY] The residual levels of chlorine (hypochlorite ion and hypochlorous acid), chlorine
     dioxide, chlorate ion, chloramine and disinfection by-products shall be monitored in the
     finished drinking water to ensure compliance to all applicable regulations. Also,
     reference the AWWA B300 (Hypochlorites) standard's Recommendations for the Handling and
     Storage of Hypochlorite Solutions appendix for information on preservation techniques
     for hypochlorite bleach in transit and storage.


Facility : Nitro, WV


Aluminum Sulfate[AL]
Trade Designation Product Function Max Use
Aluminum Sulfate 50% Coagulation & Flocculation 150mg/L
Aluminum Sulfate 50% SOLN Coagulation & Flocculation 150mg/L
Aluminum Sulfate 50% Solution Coagulation & Flocculation 150mg/L
Aluminum Sulfate Solution Coagulation & Flocculation 150 mg/L
Liquid Alum Coagulation & Flocculation 150 mg/L

[AL] Based on an evaluation of health effects data, the level of aluminum in the finished
     drinking water shall not exceed 2 mg/L.

Chlorine[CL]
Trade Designation Product Function Max Use
Chlorine, Liquified Gas Disinfection & Oxidation 30mg/L

[CL] The residual levels of chlorine (hypochlorite ion and hypochlorous acid), chlorine
     dioxide, chlorate ion, chloramine and disinfection by-products shall be monitored in the
     finished drinking water to ensure compliance to all applicable regulations.

Hydrogen Peroxide [HP]
Trade Designation Product Function Max Use
Hydrogen Peroxide 30%[1] Oxidant 3.5mg/L
Hydrogen Peroxide 30% Disinfection & Oxidation 3.5mg/L
Hydrogen Peroxide 32%[2] Oxidant 3.3mg/L
Hydrogen Peroxide 32% Disinfection & Oxidation 3.3mg/L
Hydrogen Peroxide 35%[3] Oxidant 3mg/L
Hydrogen Peroxide 35% Disinfection & Oxidation 3mg/L
Hydrogen Peroxide 50% Disinfection & Oxidation 2.1mg/L
Hydrogen Peroxide 8% Disinfection & Oxidation 13mg/L
Hydrogen Peroxide 8% Oxidant 13mg/L

[1] This product may be used at a maximum use level of 95 mg/L for the following functions:
    - reoxygenation of treated water
    - oxidation of organic residuals
    - oxidation of any reduced products, such as Fe(II) and sulfides
    Treatment must be followed by chlorination to a chlorine residual not to exceed 4 mg/L,
    the EPA's proposed maximum residual level.
[2] This product may be used at a maximum use level of 90 mg/L for the following functions:
    - reoxygenation of treated water
    - oxidation of organic residuals
    - oxidation of any reduced products, such as Fe(II) and sulfides
    Treatment must be followed by chlorination to a chlorine residual not to exceed 4 mg/L,
    the EPA's proposed maximum residual level.
[3] This product may be used at a maximum use level of 85 mg/L for the following functions:
    - reoxygenation of treated water
    - oxidation of organic residuals
    - oxidation of any reduced products, such as Fe(II) and sulfides
    Treatment must be followed by chlorination to a chlorine residual not to exceed 4 mg/L,
    the EPA's proposed maximum residual level.
[HP] Use of this product shall be followed by chlorination to remove levels of hydrogen
     peroxide.  Chlorine residuals shall not exceed 4 mg/L, the EPA's proposed maximum
     residual level.

Polyaluminum Chloride[AL]
Trade Designation Product Function Max Use
Brennfloc BC 2380 Coagulation & Flocculation 200mg/L
Brennfloc BC 2381 Coagulation & Flocculation 200mg/L

[AL] Based on an evaluation of health effects data, the level of aluminum in the finished
     drinking water shall not exceed 2 mg/L.

Potassium Hydroxide
Trade Designation Product Function Max Use
Caustic Potash 45% Corrosion & Scale Control 100 mg/L
Potassium Hydroxide Corrosion & Scale Control 100 mg/L

Sodium Hypochlorite[HY]
Trade Designation Product Function Max Use
SNO-GLO BLEACH Disinfection & Oxidation 105mg/L
Sno-Glo 10% Bleach Disinfection & Oxidation 105mg/L
Sodium Hypochlorite 12.5% Disinfection & Oxidation 84mg/L
Sodium Hypochlorite, 10% Disinfection & Oxidation 105mg/L

[HY] The residual levels of chlorine (hypochlorite ion and hypochlorous acid), chlorine
     dioxide, chlorate ion, chloramine and disinfection by-products shall be monitored in the
     finished drinking water to ensure compliance to all applicable regulations. Also,
     reference the AWWA B300 (Hypochlorites) standard's Recommendations for the Handling and
     Storage of Hypochlorite Solutions appendix for information on preservation techniques
     for hypochlorite bleach in transit and storage.


Facility : Kansas City South


Sodium Hydroxide[1]
Trade Designation Product Function Max Use
Caustic Soda 20% Corrosion & Scale Control 250mg/L
Caustic Soda 25% Corrosion & Scale Control 200mg/L
Caustic Soda 50% Corrosion & Scale Control 100mg/L
Sodium Hydroxide 20% Corrosion & Scale Control 250mg/L
Sodium Hydroxide 25% Corrosion & Scale Control 250mg/L
Sodium Hydroxide 50% Corrosion & Scale Control 100mg/L

[1] Trade designation may be followed by a three digit alpha suffix to designate the
    chlor-alkali electrolytic cell category/grade.

Sodium Hypochlorite[HY]
Trade Designation Product Function Max Use
Chem Bleach Household Disinfection & Oxidation 200mg/L
SNO-GLO-BLEACH Disinfection & Oxidation 105mg/L
Sno-Glo 10% Disinfection & Oxidation 105mg/L
Sodium Hypochlorite 10% Disinfection & Oxidation 105mg/L
Sodium Hypochlorite 12.5% Disinfection & Oxidation 84mg/L
Sodium Hypochlorite 5.25% Solution Disinfection & Oxidation 200mg/L

[HY] The residual levels of chlorine (hypochlorite ion and hypochlorous acid), chlorine
     dioxide, chlorate ion, chloramine and disinfection by-products shall be monitored in the
     finished drinking water to ensure compliance to all applicable regulations. Also,
     reference the AWWA B300 (Hypochlorites) standard's Recommendations for the Handling and
     Storage of Hypochlorite Solutions appendix for information on preservation techniques
     for hypochlorite bleach in transit and storage.

Sulfuric Acid
Trade Designation Product Function Max Use
Sulfuric Acid Corrosion & Scale Control
pH Adjustment
50mg/L
Sulfuric Acid 50% Corrosion & Scale Control
pH Adjustment
93mg/L
Sulfuric Acid 66 Degree Corrosion & Scale Control
pH Adjustment
50mg/L

NOTE: Only products bearing the NSF Mark on the product, product packaging, and/or
      documentation shipped with the product are Certified.

Facility : St. Louis, MO - Chouteau


Aluminum Chlorohydrate[AL]
Trade Designation Product Function Max Use
Brennfloc 4000 Coagulation & Flocculation 250mg/L
Brennfloc BC4105[PY] Coagulation & Flocculation 31mg/L

[AL] Based on an evaluation of health effects data, the level of aluminum in the finished
     drinking water shall not exceed 2 mg/L.
[PY] Polyamines Certified by NSF International comply with 40 CER 141.111 requirements for
     percent monomer and dose.

Ammonium Hydroxide
Trade Designation Product Function Max Use
Ammonium Hydroxide 19% Chloramination 10mg/L

Ammonium Sulfate
Trade Designation Product Function Max Use
Ammonium Sulfate Chloramination 60mg/L
Ammonium Sulfate Solution Chloramination 60mg/L

Blended Corrosion Inhibitor
Trade Designation Product Function Max Use
Robin Phos PO-2 Corrosion & Scale Control
Sequestering
20 mg/L

Blended Phosphates
Trade Designation Product Function Max Use
AquaPure 3637 Corrosion & Scale Control
Sequestering
25mg/L
AquaPure 3655 Corrosion & Scale Control
Sequestering
25mg/L
AquaPure 3673 Corrosion & Scale Control
Sequestering
25mg/L
AquaPure 3691 Corrosion & Scale Control
Sequestering
25mg/L
Robin Phos PO-73 Corrosion & Scale Control
Sequestering
25 mg/L

Miscellaneous Chemical Products
Trade Designation Product Function Max Use
Brennfloc 4220[AL] Coagulation & Flocculation 250mg/L
Brennfloc 4420[AL] [PY] Coagulation & Flocculation 100mg/L
Brennfloc 4420H[AL] [PY] Coagulation & Flocculation 100mg/L
Robin 3000 Coagulation & Flocculation 15mg/L
RobinFloc 1212 Coagulation & Flocculation 15mg/L
Robinfloc 2000[PY] Coagulation & Flocculation 15mg/L

[AL] Based on an evaluation of health effects data, the level of aluminum in the finished
     drinking water shall not exceed 2 mg/L.
[PY] Polyamines Certified by NSF International comply with 40 CER 141.111 requirements for
     percent monomer and dose.

Miscellaneous Water Supply Products
Trade Designation Product Function Max Use
Citric Acid 30-50%[1] [2] Membrane Cleaner NA

[1] This product is designed to be used off-line and flushed out prior to using the system
    for drinking water, following manufacturer's use instructions.
[2] The pH of the influent and effluent water should be monitored to ensure that all traces
    of the product have been removed before placing into service.

Monosodium Orthophosphate
Trade Designation Product Function Max Use
AquaPure 3601 Corrosion & Scale Control 25mg/L

Poly (Diallyldimethylammonium Chloride)(pDADMAC)
Trade Designation Product Function Max Use
Brennfloc CP 7215P Coagulation & Flocculation 100mg/L
Robin 110 Coagulation & Flocculation 100mg/L
Robin 120 Coagulation & Flocculation 50 mg/L
Robin 220 Coagulation & Flocculation 50mg/L
RobinFloc 4325 Coagulation & Flocculation 100mg/L
RobinFloc 4728 Coagulation & Flocculation 96mg/L

Polyaluminum Chloride[AL]
Trade Designation Product Function Max Use
Aluminum Chloride Hydroxide Aqueous Solution Coagulation & Flocculation 250 mg/L
Aluminum Chlorohydrate Aqueous Solution Coagulation & Flocculation 250 mg/L
Brennfloc 4000 Coagulation & Flocculation 250mg/L
Robin AC-100 Coagulation & Flocculation 250 mg/L
RobinFloc 4708 Coagulation & Flocculation 250mg/L

[AL] Based on an evaluation of health effects data, the level of aluminum in the finished
     drinking water shall not exceed 2 mg/L.

Polymer Blends[AL] [PY]
Trade Designation Product Function Max Use
AC 2602 PA Coagulation & Flocculation 50mg/L
Brennfloc BC 4101 Coagulation & Flocculation 66mg/L
Polyaluminum Sulfate Coagulation & Flocculation 150 mg/L
Polyaluminum Sulfate Polymer Emulsion Coagulation & Flocculation 150mg/L
Robin AC 110 Coagulation & Flocculation 130 mg/L
Robin AC-3545 Coagulation & Flocculation 50 mg/L
Robin AS-110 Coagulation & Flocculation 150 mg/L
Robin AS-120 Coagulation & Flocculation 150 mg/L
Robin AS-140 Coagulation & Flocculation 100 mg/L
Robin FR-2003 Coagulation & Flocculation 20mg/L
RobinFloc 4707 Coagulation & Flocculation
Flocculant
100mg/L
RobinFloc 4714 Coagulation & Flocculation 238mg/L
RobinFloc 4715 Coagulation & Flocculation 156mg/L
RobinFloc 4725 Coagulation & Flocculation 155mg/L
RobinFloc 4740 Coagulation & Flocculation
Flocculant
68mg/L

[AL] Based on an evaluation of health effects data, the level of aluminum in the finished
     drinking water shall not exceed 2 mg/L.
[PY] Polyamines Certified by NSF International comply with 40 CER 141.111 requirements for
     percent monomer and dose.

Sodium Permanganate[MN]
Trade Designation Product Function Max Use
Sodium Permanganate Oxidant 176mg/L
Sodium Permanganate Solution Oxidant 176mg/L
Sodium Permanganate Solution 15% Oxidant 235mg/L
Sodium Permanganate Solution 19% Oxidant 185mg/L

[MN] The finished drinking water should be monitored to ensure that levels of manganese do
     not exceed .05 mg/L.

Sodium Polyphosphates, Glassy
Trade Designation Product Function Max Use
AquaPure SH 36 Corrosion & Scale Control 25mg/L
Robin Phos P-1 Corrosion Control
Sequestering
28 mg/L
SHMP Corrosion Control
Sequestering
28mg/L
Sodium Hexametaphosphate Corrosion Control
Sequestering
28mg/L
Sodium Polyphosphate Corrosion Control
Sequestering
28mg/L
Sodium Polyphosphates Glassy Corrosion Control
Sequestering
28mg/L


Facility : St. Louis, MO - Soper


Aluminum Sulfate[AL]
Trade Designation Product Function Max Use
Aluminum Sulfate Liquid Coagulation & Flocculation 150mg/L
Aluminum Sulfate Solution Coagulation & Flocculation 150mg/L
Dialuminum Sulfate Solution Coagulation & Flocculation 150mg/L
Liquid Alum Coagulation & Flocculation 150mg/L
Polyaluminum Sulfate Solution Coagulation & Flocculation 150mg/L

[AL] Based on an evaluation of health effects data, the level of aluminum in the finished
     drinking water shall not exceed 2 mg/L.

Ferric Chloride
Trade Designation Product Function Max Use
Ferric Chloride 38-42% Coagulation & Flocculation 250mg/L
Ferric Chloride Liquid Coagulation & Flocculation 250mg/L
Ferric Chloride Solution Coagulation & Flocculation 250mg/L
Iron (III) Chloride Solution Coagulation & Flocculation 250mg/L
Iron Trichloride Solution Coagulation & Flocculation 250mg/L

Ferric Sulfate
Trade Designation Product Function Max Use
Ferric Sulfate Solution Coagulation & Flocculation 500mg/L
Iron (III) Sulfate Solution Coagulation & Flocculation 500mg/L
Iron Persulfate Solution Coagulation & Flocculation 500mg/L

Potassium Hydroxide
Trade Designation Product Function Max Use
Caustic Potash 45% pH Adjustment 100mg/L
Potassium Hydroxide pH Adjustment 100mg/L

Sodium Hydroxide[1]
Trade Designation Product Function Max Use
Caustic Soda 10% Corrosion & Scale Control
pH Adjustment
500mg/L
Caustic Soda 20% Corrosion & Scale Control
pH Adjustment
250mg/L
Caustic Soda 25% Corrosion & Scale Control
pH Adjustment
200mg/L
Caustic Soda 30% Corrosion & Scale Control
pH Adjustment
166mg/L
Caustic Soda 50% Corrosion & Scale Control
pH Adjustment
100mg/L
Sodium Hydroxide 10% Corrosion & Scale Control
pH Adjustment
500mg/L
Sodium Hydroxide 20% Corrosion & Scale Control
pH Adjustment
250mg/L
Sodium Hydroxide 25% Corrosion & Scale Control
pH Adjustment
200mg/L
Sodium Hydroxide 30% Corrosion & Scale Control
pH Adjustment
166mg/L
Sodium Hydroxide 50% Corrosion & Scale Control
pH Adjustment
100mg/L

[1] Trade Designation may be followed by a three digit alpha suffix to designate the
    chlor-alkali electrolytic cell category/grade.

Sodium Permanganate[PO]
Trade Designation Product Function Max Use
Sodium Permanganate Oxidant 176mg/L
Sodium Permanganate 15% Oxidant 235mg/L
Sodium Permanganate 19% Oxidant 185mg/L
Sodium Permanganate 20% Oxidant 176mg/L
Sodium Permanganate 40% Oxidant 88mg/L
Sodium Permanganate Solution Oxidant 176mg/L

[PO] The finished drinking water shall be monitored to ensure that levels of manganese

     do not exceed 0.05 mg/L.

Sulfuric Acid
Trade Designation Product Function Max Use
Sulfuric Acid Corrosion & Scale Control
pH Adjustment
50mg/L
Sulfuric Acid 66 Corrosion & Scale Control
pH Adjustment
50mg/L
Sulfuric Acid 66 Baumé Corrosion & Scale Control
pH Adjustment
50mg/L
Sulfuric Acid 66Be Corrosion & Scale Control
pH Adjustment
50mg/L
Sulfuric Acid 93% Corrosion & Scale Control
pH Adjustment
50mg/L

NOTE: Only products bearing the NSF Mark on the product, packing, and/or documentation shipped
      with the product are Certified.

Number of matching Manufacturers is 1
Number of matching Products is 622
Processing time was 0 seconds