NSF Product and Service Listings

These NSF Official Listings are current as of Saturday, December 20, 2014 at 12:15 a.m. Eastern Time. Please contact NSF International to confirm the status of any Listing, report errors, or make suggestions.

Alert: NSF is concerned about fraudulent downloading and manipulation of website text. Always confirm this information by clicking on the below link for the most accurate information: http://info.nsf.org/Certified/PwsChemicals/Listings.asp?ProductFunction=Well+Drilling+Aid&


NSF/ANSI 60
Drinking Water Treatment Chemicals - Health Effects



 
ABI, Inc. 
375 Roma Jean Parkway
Streamwood, IL 60107 
United States 
800-992-2880 
630-372-7300

Facility : # 1 USA


Miscellaneous Water Supply Products[WL]
Trade Designation Product Function Max Use
ABI Crumbles Well Drilling Aid NA
ABI Gel Well Drilling Aid NA
ABI Granular Well Drilling Aid NA
ABI Grout Well Drilling Aid NA
ABI Hi Yield Well Drilling Aid NA
ABI Plug Well Drilling Aid NA

[WL] These products are designed to be flushed out prior to using the system for drinking

     water.  The well shall be properly flushed and drained before being placed in service.



 
Akzo Nobel Surface Chemistry LLC 
909 Mueller Avenue
Chattanooga, TN 37406-0401 
United States 
800-251-1080 
423-629-1405

Facility : Chattanooga, TN


Miscellaneous Water Supply Products
Trade Designation Product Function Max Use
Alcodrill® HPD-L[1] [WL] Well Drilling Aid NA

[1] Certification of these products is based on a well drilling model with the following
    assumptions:
    The amount of well drilling aid used is 3780 liters (1000 U.S. gallons) to which the
    drilling fluid has been added at the manufacturer's recommended level. The aquifer
    contains 3.1 million liters (815,000 gallons) based on a 0.5 acre aquifer of 6.1 meter
    depth (20 ft.) and 25% porosity. The bore hole is 61 meters in total depth (200 ft.),
    the screen is 6.1 meters in length (20 ft.), and the bore hole is 25.4 cm in diameter
    (10 in.). The amount of well drilling fluid removed from the well during construction is
    equal to the combined volumes of the casing, the screen, and the bore hole annulus
    around the casing and the screen, plus an additional amount removed through the well
    disinfection and development (90% removed).
[WL] These products are designed to be flushed out prior to using the system for drinking

     water.  The well shall be properly flushed and drained before being placed in service.



 
Alpine Technical Services, LLC 
601 West 6825 South
Midvale, UT 84047 
United States 
801-255-5336

Facility : # 2 USA


Miscellaneous Water Supply Products
Trade Designation Product Function Max Use
ATS-9003[1] [2] Well Cleaning Aid
Well Drilling Aid
NA

[1] This product is designed to be flushed out prior to using the system for drinking water.
    The well is to be properly flushed and drained before being placed into service. This
    product is to be used according to the manufacturer's use instructions.
[2] These products are designed to be flushed out prior to using the system for drinking
    water. Before being placed into service, the well is to be properly flushed according
    to the manufacturer's use instructions. Certification of these products is based on
    the well drilling model with the following assumptions:
    - The amount of well drilling fluid used is 3780 L (1000 U.S. gallons) to which
    the drilling fluid has been added at the manufacturer's recommended level.
    - The aquifer contains 3.1 million liters of water (815,000 gallons) based on a 0.5
    acre aquifer of 6.1 meter depth (20 ft.) and 25% porosity.
    - The bore hole is 61 meters in total depth (200 ft.), the screen is 6.1 meters in
    length (20 ft.), and the bore hole is 25.4 cm. in diameter (10 in.).
    - The amount of well drilling fluid removed from the well during construction is equal
    to the combined volumes of the casing and the screen, plus an additional amount removed
    through the well disinfection and development (90% removed).
    - This product should not be used in constructing wells in highly porous formations,
    such as cavernous limestone.

Polyacrylamide [PC]
Trade Designation Product Function Max Use
ATS-3858[1] [2] Well Drilling Aid NA

[1] This product is designed to be flushed out prior to using the system for drinking water.
    The well is to be properly flushed and drained before being placed into service. This
    product is to be used according to the manufacturer's use instructions.
[2] These products are designed to be flushed out prior to using the system for drinking
    water. Before being placed into service, the well is to be properly flushed according
    to the manufacturer's use instructions. Certification of these products is based on
    the well drilling model with the following assumptions:
    - The amount of well drilling fluid used is 3780 L (1000 U.S. gallons) to which
    the drilling fluid has been added at the manufacturer's recommended level.
    - The aquifer contains 3.1 million liters of water (815,000 gallons) based on a 0.5
    acre aquifer of 6.1 meter depth (20 ft.) and 25% porosity.
    - The bore hole is 61 meters in total depth (200 ft.), the screen is 6.1 meters in
    length (20 ft.), and the bore hole is 25.4 cm. in diameter (10 in.).
    - The amount of well drilling fluid removed from the well during construction is equal
    to the combined volumes of the casing and the screen, plus an additional amount removed
    through the well disinfection and development (90% removed).
    - This product should not be used in constructing wells in highly porous formations,
    such as cavernous limestone.
[PC] Polyacrylamide Products Certified by NSF International comply with 40 CFR 141.111
     requirements for percent monomer and dose.



 
AMC 
1880 North 2200 West
Suite 40 
Salt Lake City, UT 84116 
United States 
61 8 9445 4000
Visit this company's website

Facility : # 1 USA


Bentonite[1]
Trade Designation Product Function Max Use
AUS-BEN XTRA Well Drilling Aid NA
Aus-Gel Xtra Well Drilling Aid NA

[1] Prior to using the system for drinking water, the well is to be properly flushed until
    the turbidity of the water is <1 NTU.



 
AMC 
1880 North 2200 West
Suite 40 
Salt Lake City, UT 84116 
United States 
801-364-0233

Facility : # 1 USA


Miscellaneous Water Supply Products
Trade Designation Product Function Max Use
Liquisperse HT[1] [2] Well Cleaning Aid
Well Drilling Aid
NA

[1] This product is designed to be flushed out prior to using the system for drinking water.
     The well is to be properly flushed and drained before being placed into service.  This
    product is to be used according to the manufacturer's use instructions.
[2] These products are designed to be flushed out prior to using the system for drinking
    water. Before being placed into service, the well is to be properly flushed according to
    the manufacturer's use instructions. Certification of these products is based on the
    well drilling model with the following assumptions: 
    - The amount of well drilling fluid used is 3780 L (1000 U.S. gallons) to which
      the drilling fluid has been added at the manufacturer's recommended level.
    - The aquifer contains 3.1 million liters of water (815,000 gallons) based on a 0.5
      acre aquifer of 6.1 meter depth (20 ft.) and 25% porosity.
    - The bore hole is 61 meters in total depth (200 ft.), the screen is 6.1 meters in 
      length (20 ft.), and the bore hole is 25.4 cm. in diameter (10 in.).
    - The amount of well drilling fluid removed from the well during construction is equal 
      to the combined volumes of the casing and the screen, plus an additional amount 
      removed through the well disinfection and development (90% removed).
    - This product should not be used in constructing wells in highly porous formations, 
      such as cavernous limestone.

Polyacrylamide [PC]
Trade Designation Product Function Max Use
Clay Doctor[1] [2] Well Drilling Aid NA
Liquipol[1] [2] Well Drilling Aid NA

[1] This product is designed to be flushed out prior to using the system for drinking water.
     The well is to be properly flushed and drained before being placed into service.  This
    product is to be used according to the manufacturer's use instructions.
[2] These products are designed to be flushed out prior to using the system for drinking
    water. Before being placed into service, the well is to be properly flushed according to
    the manufacturer's use instructions. Certification of these products is based on the
    well drilling model with the following assumptions: 
    - The amount of well drilling fluid used is 3780 L (1000 U.S. gallons) to which
      the drilling fluid has been added at the manufacturer's recommended level.
    - The aquifer contains 3.1 million liters of water (815,000 gallons) based on a 0.5
      acre aquifer of 6.1 meter depth (20 ft.) and 25% porosity.
    - The bore hole is 61 meters in total depth (200 ft.), the screen is 6.1 meters in 
      length (20 ft.), and the bore hole is 25.4 cm. in diameter (10 in.).
    - The amount of well drilling fluid removed from the well during construction is equal 
      to the combined volumes of the casing and the screen, plus an additional amount 
      removed through the well disinfection and development (90% removed).
    - This product should not be used in constructing wells in highly porous formations, 
      such as cavernous limestone.
[PC] Polyacrylamide Products Certified by NSF International comply with 40 CFR 141.111
     requirements for percent monomer and dose.



 
AMC 
1880 North 2200 West
Suite 40 
Salt Lake City, UT 84116 
United States 
801-364-0233

Facility : # 1 USA


Miscellaneous Water Supply Products[1] [2]
Trade Designation Product Function Max Use
Ezee-Pac L Well Drilling Aid NA
Ezee-Trol L Well Drilling Aid NA

[1] This product is designed to be used off-line and flushed out prior to using the system
    for drinking water, following manufacturer's use instructions.
[2] The well is to be properly flushed until the turbidity of the water is <1 NTU.



 
AMC 
1880 North, 2200 West
Suite 40 
Salt Lake City, UT 84116 
United States 
801-364-0233
Visit this company's website

Facility : # 5 USA


Miscellaneous Water Supply Products
Trade Designation Product Function Max Use
AMC COREWELL[1] [PC] Well Drilling Aid NA
AMC Ezee Pac L[3] [4] Well Drilling Aid NA
AMC Ezee Pac R[3] [4] Well Drilling Aid NA
CR-650[1] [PC] Well Drilling Aid NA
Clay Doctor[1] [PC] Well Drilling Aid NA
Liqui Sperse HT[1] Well Drilling Aid
Well Cleaning Aid
NA

[1] These products are designed to be flushed out prior to using the system for drinking
    water. Before being placed into service, the well is to be properly flushed according to
    the manufacturer's use instructions. Certification of these products is based on the
    well drilling model with the following assumptions:
    - The amount of well drilling fluid is 3780 L (1000 U.S. gallons) to which the drilling 
      fluid has been added at the manufacturer's recommended level. 
    - The aquifer contains 3.1 million liters of water (815,000 gallons) based on a 0.5 acre
    
      aquifer of 6.1 meter depth (20 ft.) and 25% porosity.
    - The bore hole is 61 meters in total depth (200 ft.), the screen is 6.1 meters in
    length 
      (20 ft.), and the bore hole is 25.4 cm in diameter (10 in.).
    - The amount of well drilling fluid removed from the well during construction is equal
    to 
      the combined volumes of the casing and the screen, plus an additional amount removed 
      through the well disinfection and development (90% removed). 
    - This product should not be used in constructing wells in highly porous formations,
    such
      as cavernous limestone. 
    
[2] Certification of this product is based on a well drilling model using assumption in
    NSF/ANSI Standard 60, Section 8 for well drilling foamers.
[3] This product is designed to be used off-line and flushed prior to using the system for
    drinking water, following manufacturer's use instructions.
[4] This product is designed to be flusehd out until the turbidity of the water is <1
    NTU.F;lusing is required before the system may be used for drinking water.
[PC] Polyacrylamide Products Certified by NSF International comply with 40 CFR 141.111
     requirements for percent monomer and dose.

Polyacrylamide[1] [PC]
Trade Designation Product Function Max Use
Aus-Plug Drilling Fluid
Well Drilling Aid
NA

[1] These products are designed to be flushed out prior to using the system for drinking
    water. Before being placed into service, the well is to be properly flushed according to
    the manufacturer's use instructions. Certification of these products is based on the
    well drilling model with the following assumptions:
    - The amount of well drilling fluid is 3780 L (1000 U.S. gallons) to which the drilling 
      fluid has been added at the manufacturer's recommended level. 
    - The aquifer contains 3.1 million liters of water (815,000 gallons) based on a 0.5 acre
    
      aquifer of 6.1 meter depth (20 ft.) and 25% porosity.
    - The bore hole is 61 meters in total depth (200 ft.), the screen is 6.1 meters in
    length 
      (20 ft.), and the bore hole is 25.4 cm in diameter (10 in.).
    - The amount of well drilling fluid removed from the well during construction is equal
    to 
      the combined volumes of the casing and the screen, plus an additional amount removed 
      through the well disinfection and development (90% removed). 
    - This product should not be used in constructing wells in highly porous formations,
    such
      as cavernous limestone. 
    
[PC] Polyacrylamide Products Certified by NSF International comply with 40 CFR 141.111
     requirements for percent monomer and dose.



 
AMC North America Limited 
10911-72nd Street South East
Calgary, AB T2C 3G2 
Canada 
403-259-5112

Facility : # 1 USA


Bentonite
Trade Designation Product Function Max Use
AUS-Gel Drilling Fluid
Well Drilling Aid
NA



 
Aquamark, Inc. 
P.O. Box 773
Chesterland, OH 44026 
United States 
440-564-1227

Facility : # 1 USA


Polyacrylamide [PC]
Trade Designation Product Function Max Use
AQ 310-P[1] [2] Well Drilling Aid NA

[1] This product is designed to be flushed out prior to using the system for drinking
    water.
  The well is to be properly flushed and drained before being placed into
    service. This product is to be used according to the manufacturer's use instructions.

[2] These products are designed to be flushed out prior to using the system for drinking
    water. Before being placed into service, the well is to be properly flushed according to
    the manufacturer's use instructions. Certification of these products is based on the
    well
    drilling model with the following assumptions: 
    - The amount of well drilling fluid used is 3780 L (1000 U.S. gallons) to which
      the drilling fluid has been added at the manufacturer's recommended level.
    - The aquifer contains 3.1 million liters of water (815,000 gallons) based on a 0.5 acre
      aquifer of 6.1 meter depth (20 ft.) and 25% porosity.
    - The bore hole is 61 meters in total depth (200 ft.), the screen is 6.1 meters in
    length
      (20 ft.), and the bore hole is 25.4 cm. in diameter (10 in.).
    - The amount of well drilling fluid removed from the well during construction is equal
    to
      the combined volumes of the casing and the screen, plus an additional amount removed 
      through the well disinfection and development (90% removed).
    - This product should not be used in constructing wells in highly porous formations,
    such
      as cavernous limestone.
[PC] Polyacrylamide Products Certified by NSF International comply with 40 CFR 141.111
     requirements for percent monomer and dose.

[PY] Polyamines Certified by NSF International comply with 40 CFR 141.111 requirements for
     percent monomer and dose.


 
Ashland Inc. 
P.O. Box 2219
Columbus, OH 43216 
United States 
614-790-3333
Visit this company's website

Facility : Kenedy, Texas


Miscellaneous Water Supply Products[1] [2]
Trade Designation Product Function Max Use
AQUAVIS ETD HV Well Drilling Aid NA
AQUAVIS ETD LV Well Drilling Aid NA
AQUAVIS ETD MV Well Drilling Aid NA
AQUAVIS ETD UHV Well Drilling Aid NA
AQUAVIS ETD VHV Well Drilling Aid NA

[1] This product is designed to be used off-line and flushed out prior to using the system
    for drinking water, following manufacturer's use instructions.
[2] This product is designed to be flushed out until the turbidity of the water is < 1 NTU. 
    Flushing is required before the system may be used for drinking water.


Facility : Hopewell, Virginia


Miscellaneous Water Supply Products[1] [2] [3]
Trade Designation Product Function Max Use
AquaFLO™ HV Drilling Fluid
Well Drilling Aid
NA
AquaFLO™ LV Drilling Fluid
Well Drilling Aid
NA
AquaPAC™ LV Drilling Fluid
Well Drilling Aid
NA
AquaPAC™ Regular Drilling Fluid
Well Drilling Aid
NA
Aquavis 2740 Drilling Fluid
Well Drilling Aid
NA

[1] This product has been evaluated to the requirements of NSF/ANSI Standard 60, Annex C,
    utilizing an additional test based on ASTM Standard G22 to ensure the product does not
    support microbial growth.
[2] This product is designed to be used off-line and flushed out prior to using the system
    for drinking water, following manufacturer's use instructions.
[3] This product is designed to be flushed out until the turbidity of the water is <1 NTU. 
    Flushing is required before the system may be used for drinking water.



 
BASF Corporation - Water Solutions (formerly Ciba Corporation) 
2371 Wilroy Road
Suffolk, VA 23439 
United States 
757-538-3700

Facility : # 11 USA


Miscellaneous Water Supply Products [PC]
Trade Designation Product Function Max Use
Agefloc WT6303[1] Well Drilling Aid NA
Alcomer 123LA[1] Well Drilling Aid NA

[1] These products should not be used in constructing wells in highly porous formations such
    as cavernous limestone.
    These products are designed to be flushed out prior to using the system for drinking
    water. Before being placed in service, the well is to be properly flushed according to
    the manufacturer's use instructions.
    Certification of these products is based on a well drilling model with the following
    assumptions:
    The amount of well drilling fluid used is 3780 L (1000 U.S. gallons) to which the
    drilling fluid has been added at the manufacturer's recommended level. The aquifer
    contains 3.1 million liters of water (815,000 gallons) based on a 0.5 acre aquifer of
    6.1 meter depth (20 ft.) and 25% porosity. The bore hole is 61 meters in total depth
    (200 ft.), the screen is 6.1 meters in length (20 ft.), and the bore hole is 25.4 cm in
    diameter (10 in.). The amount of well drilling fluid removed from the well during
    construction is equal to the combined volumes of the casing, the screen, and the bore
    hole annuals around the casing and the screen, plus an additional amount removed through
    the well disinfection and development (90% removed).
[PC] Polyacrylamide Products Certified by NSF International comply with 40 CFR 141.111
     requirements for percent monomer and dose.


Facility : # 12 USA


Miscellaneous Water Supply Products [PC]
Trade Designation Product Function Max Use
Agefloc WT6303[1] Well Drilling Aid NA
Alcomer 123LA[1] Well Drilling Aid NA

[1] These products should not be used in constructing wells in highly porous formations such
    as cavernous limestone.
    These products are designed to be flushed out prior to using the system for drinking
    water. Before being placed in service, the well is to be properly flushed according to
    the manufacturer's use instructions.
    Certification of these products is based on a well drilling model with the following
    assumptions:
    The amount of well drilling fluid used is 3780 L (1000 U.S. gallons) to which the
    drilling fluid has been added at the manufacturer's recommended level. The aquifer
    contains 3.1 million liters of water (815,000 gallons) based on a 0.5 acre aquifer of
    6.1 meter depth (20 ft.) and 25% porosity. The bore hole is 61 meters in total depth
    (200 ft.), the screen is 6.1 meters in length (20 ft.), and the bore hole is 25.4 cm in
    diameter (10 in.). The amount of well drilling fluid removed from the well during
    construction is equal to the combined volumes of the casing, the screen, and the bore
    hole annuals around the casing and the screen, plus an additional amount removed through
    the well disinfection and development (90% removed).
[PC] Polyacrylamide Products Certified by NSF International comply with 40 CFR 141.111
     requirements for percent monomer and dose.


Facility : # 15 USA


Miscellaneous Water Supply Products [PC]
Trade Designation Product Function Max Use
Alcomer 123LA[1] Well Drilling Aid NA

[1] These products are designed to be flushed out prior to using the system for drinking
    water. Before being placed into service, the well is to be properly flushed according to
    the manufacturer's use instructions. Certification of these products is based on the
    well drilling model with the following assumptions: 
    The amount of well drilling fluid used is 3780 L (1000 U.S. gallons) to which the
    drilling fluid has been added at the manufacturer's recommended level. The aquifer
    contains 3.1 million liters of water (815,000 gallons) based on a 0.5 acre aquifer of
    6.1 meter depth (20 ft.) and 25% porosity. The bore hole is 61 meters in total depth
    (200 ft.), the screen is 6.1 meters in length (20 ft.), and the bore hole is 25.4 cm. in
    diameter (10 in.). The amount of well drilling fluid removed from the well during
    construction is equal to the combined volumes of the casing and the screen, plus an
    additional amount removed through the well disinfection and development (90% removed).
    This product should not be used in constructing wells in highly porous formations, such
    as cavernous limestone.
[PC] Polyacrylamide Products Certified by NSF International comply with 40 CFR 141.111
     requirements for percent monomer and dose.


Facility : # 17 USA


Miscellaneous Water Supply Products[1] [PC]
Trade Designation Product Function Max Use
Alcomer 120L Well Drilling Aid NA
Alcomer 74L Well Drilling Aid NA
Alcomer XX-Poly Well Drilling Aid NA
Magnafloc 120L Well Drilling Aid NA

[1] This product is designed to be used off-line following manufacturer’s use instructions.
    The well is to be flushed until the turbidity of the water is < 1 NTU before the system
    may be used for drinking water.
[PC] Polyacrylamide Products Certified by NSF International comply with 40 CFR 141.111
     requirements for percent monomer and dose.

Polyacrylamide [PC]
Trade Designation Product Function Max Use
Alcomer 110RD[2] Well Drilling Aid NA

[2] These products should not be used in constructing wells in highly porous formations such
    as cavernous limestone. 
    These products are designed to be flushed out prior to using the system for drinking
    water. Before being placed in service, the well is to be properly flushed according to
    the manufacturer's use instructions. 
    Certification of these products is based on a well drilling model with the following
    assumptions: 
    The amount of well drilling fluid used is 3780 L (1000 U.S. gallons) to which the
    drilling fluid has been added at the manufacturer's recommended level. The aquifer
    contains 3.1 million liters of water (815,000 gallons) based on a 0.5 acre aquifer of
    6.1 meter depth (20 ft.) and 25% porosity. The bore hole is 61 meters in total depth
    (200 ft.), the screen is 6.1 meters in length (20 ft.), and the bore hole is 25.4 cm in
    diameter (10 in.). The amount of drilling fluid removed from the well during
    construction is equal to the combined volumes of the casing, the screen, and the bore
    hole annuals around the casing and the screen, plus an additional amount removed through
    the well disinfection and development (90% removed).
[PC] Polyacrylamide Products Certified by NSF International comply with 40 CFR 141.111
     requirements for percent monomer and dose.


Facility : Suffolk, VA


Miscellaneous Water Supply Products
Trade Designation Product Function Max Use
ALCOMER XX-Poly[1] Well Drilling Aid NA
Alcomer 110RD Well Drilling Aid NA
Alcomer 120L[1] Well Drilling Aid NA
Alcomer 123LA[1] [PC] Well Drilling Aid NA
Alcomer 1771[1] Well Drilling Aid NA
Alcomer 24 (UK)[1] Well Drilling Aid NA
Alcomer 74L Well Drilling Aid NA
Magnafloc 120L[1] Well Drilling Aid NA

[1] These products are designed to be flushed out prior to using the system for drinking
    water. Before being placed into service, the well is to be properly flushed according to
    the manufacturer's use instructions. Certification of these products is based on the
    well
    drilling model with the following assumptions:
      - The amount of well drilling fluid used is 3780 L (1000 U.S. gallons) to which the
        drilling fluid has been added at the manufacturer's recommended level.
      - The aquifer contains 3.1 million liters of water (815,000 gallons) based on a 0.5 
        acre aquifer of 6.1 meter depth (20 ft.) and 25% porosity.
      - The bore hole is 61 meters in total depth (200 ft.), the screen is 6.1 meters in 
        length (20 ft.), and the bore hole is 25.4 cm. in diameter (10 in.).
      - The amount of well drilling fluid removed from the well during construction is equal
    
        to the combined volumes of the casing and the screen, plus an additional amount 
        removed through the well disinfection and development (90% removed).
      - This product should not be used in constructing wells in highly porous formations,
        such as cavernous limestone.
[PC] Polyacrylamide Products Certified by NSF International comply with 40 CFR 141.111
     requirements for percent monomer and dose.

[WL] These products are designed to be flushed out prior to using the system for drinking

     water.  The well shall be properly flushed and drained before being placed in service.


 
BASF Performance Products plc (formerly Ciba Corporation) 
P.O. Box 38
Low Moor, Bradford 
West Yorkshire BD12 OJZ 
United Kingdom 
44 1274 417 847
Visit this company's website

Facility : Bradford, United Kingdom


Miscellaneous Water Supply Products[1]
Trade Designation Product Function Max Use
Alcomer 1771 Well Drilling Aid NA
Alcomer 24 (UK) Well Drilling Aid NA

[1] These products are designed to be flushed out prior to using the system for drinking
    water.  Before being placed in service, the well is to be properly flushed according to
    the manufacturer's use instructions.
    Certification of these products is based on a well drilling model with the following
    assumptions:
      - The amount of well drilling fluid used is 3780 L (1000 U.S. gallons) to which the 
        drilling fluid has been added at the manufacturer's recommended level.
      - The aquifer contains 3.1 million liters of water (815,000 gallons) based on a 0.5 
        acre aquifer of 6.1 meter depth (20 ft.) and 25% porosity.  
      - The bore hole is 61 meters in total depth (200 ft.), the screen is 6.1 meters in
        length (20 ft.), and the bore hole is 25.4 cm in diameter (10 in.).
      - The amount of drilling fluid removed from the well during construction is equal to 
        the combined volumes of the casing, the screen, and the bore hole annuals around 
        the casing and the screen, plus an additional amount removed through the well 
        disinfection and development (90% removed).
      - These products should not be used in constructing wells in highly porous formations
        such as cavernous limestone.

Polyacrylamide [PC]
Trade Designation Product Function Max Use
Alcomer 110RD[1] Well Drilling Aid NA

[1] These products are designed to be flushed out prior to using the system for drinking
    water.  Before being placed in service, the well is to be properly flushed according to
    the manufacturer's use instructions.
    Certification of these products is based on a well drilling model with the following
    assumptions:
      - The amount of well drilling fluid used is 3780 L (1000 U.S. gallons) to which the 
        drilling fluid has been added at the manufacturer's recommended level.
      - The aquifer contains 3.1 million liters of water (815,000 gallons) based on a 0.5 
        acre aquifer of 6.1 meter depth (20 ft.) and 25% porosity.  
      - The bore hole is 61 meters in total depth (200 ft.), the screen is 6.1 meters in
        length (20 ft.), and the bore hole is 25.4 cm in diameter (10 in.).
      - The amount of drilling fluid removed from the well during construction is equal to 
        the combined volumes of the casing, the screen, and the bore hole annuals around 
        the casing and the screen, plus an additional amount removed through the well 
        disinfection and development (90% removed).
      - These products should not be used in constructing wells in highly porous formations
        such as cavernous limestone.
[PC] Polyacrylamide Products Certified by NSF International comply with 40 CFR 141.111
     requirements for percent monomer and dose.


Facility : Bradford, West Yorkshire, United Kingdom


Miscellaneous Water Supply Products[1]
Trade Designation Product Function Max Use
Alcomer 1771 Well Drilling Aid NA
Alcomer 24 (UK) Well Drilling Aid NA

[1] These products are designed to be flushed out prior to using the system for drinking
    water.  Before being placed in service, the well is to be properly flushed according to
    the manufacturer's use instructions.
    Certification of these products is based on a well drilling model with the following
    assumptions:
      - The amount of well drilling fluid used is 3780 L (1000 U.S. gallons) to which the 
        drilling fluid has been added at the manufacturer's recommended level.
      - The aquifer contains 3.1 million liters of water (815,000 gallons) based on a 0.5 
        acre aquifer of 6.1 meter depth (20 ft.) and 25% porosity.  
      - The bore hole is 61 meters in total depth (200 ft.), the screen is 6.1 meters in
        length (20 ft.), and the bore hole is 25.4 cm in diameter (10 in.).
      - The amount of drilling fluid removed from the well during construction is equal to 
        the combined volumes of the casing, the screen, and the bore hole annuals around 
        the casing and the screen, plus an additional amount removed through the well 
        disinfection and development (90% removed).
      - These products should not be used in constructing wells in highly porous formations
        such as cavernous limestone.

Polyacrylamide [PC]
Trade Designation Product Function Max Use
Alcomer 110RD[1] Well Drilling Aid NA

[1] These products are designed to be flushed out prior to using the system for drinking
    water.  Before being placed in service, the well is to be properly flushed according to
    the manufacturer's use instructions.
    Certification of these products is based on a well drilling model with the following
    assumptions:
      - The amount of well drilling fluid used is 3780 L (1000 U.S. gallons) to which the 
        drilling fluid has been added at the manufacturer's recommended level.
      - The aquifer contains 3.1 million liters of water (815,000 gallons) based on a 0.5 
        acre aquifer of 6.1 meter depth (20 ft.) and 25% porosity.  
      - The bore hole is 61 meters in total depth (200 ft.), the screen is 6.1 meters in
        length (20 ft.), and the bore hole is 25.4 cm in diameter (10 in.).
      - The amount of drilling fluid removed from the well during construction is equal to 
        the combined volumes of the casing, the screen, and the bore hole annuals around 
        the casing and the screen, plus an additional amount removed through the well 
        disinfection and development (90% removed).
      - These products should not be used in constructing wells in highly porous formations
        such as cavernous limestone.
[PC] Polyacrylamide Products Certified by NSF International comply with 40 CFR 141.111
     requirements for percent monomer and dose.


Facility : Grimsby, United Kingdom


Polyacrylamide [PC]
Trade Designation Product Function Max Use
Alcomer 110RD[1] Well Drilling Aid NA

[1] These products should not be used in constructing wells in highly porous formations such
    as cavernous limestone. 
    These products are designed to be flushed out prior to using the system for drinking
    water. Before being placed in service, the well is to be properly flushed according to
    the manufacturer's use instructions. 
    Certification of these products is based on a well drilling model with the following
    assumptions: 
    The amount of well drilling fluid used is 3780 L (1000 U.S. gallons) to which the
    drilling fluid has been added at the manufacturer's recommended level. The aquifer
    contains 3.1 million liters of water (815,000 gallons) based on a 0.5 acre aquifer of
    6.1 meter depth (20 ft.) and 25% porosity. The bore hole is 61 meters in total depth
    (200 ft.), the screen is 6.1 meters in length (20 ft.), and the bore hole is 25.4 cm in
    diameter (10 in.). The amount of drilling fluid removed from the well during
    construction is equal to the combined volumes of the casing, the screen, and the bore
    hole annuals around the casing and the screen, plus an additional amount removed through
    the well disinfection and development (90% removed).
[PC] Polyacrylamide Products Certified by NSF International comply with 40 CFR 141.111
     requirements for percent monomer and dose.



 
C.C.I. 
3540 East 26th Street
Vernon, CA 90023 
United States 
800-767-9112 
323-265-3111

Facility : # 1 USA


Polyacrylamide [PC]
Trade Designation Product Function Max Use
CP-9900[1] Well Drilling Aid NA

[1] These products are designed to be flushed out prior to using the system for drinking
    water.  Before being placed into service, the well is to be properly flushed according
    to the manufacturer's use instructions.  Certification of these products is based on the
    well drilling model with the following assumptions:
    - The amount of well drilling fluid used is 3780 L (1000 U.S. gallons) to which 
      the drilling fluid has been added at 7.6 L.
    - The aquifer contains 3.1 million liters of water (815,000 gallons) based on a 0.5 acre
      aquifer of 6.1 meter depth (20 ft.) and 25% porosity.
    - The bore hole is 61 meters in total depth (200 ft.), the screen is 6.1 meters in
    length
      (20 ft.), and the bore hole is 25.4 cm.  in diameter (10 in.).
    - The amount of well drilling fluid removed from the well during construction is equal
    to
      the combined volumes of the casing and the screen, plus an additional amount removed
      through the well disinfection and development (90% removed).
[PC] Polyacrylamide Products Certified by NSF International comply with 40 CFR 141.111
     requirements for percent monomer and dose.



 
CETCO 
Colloid Environmental Technologies Co.
2870 Forbs Avenue 
Hoffman Estates, IL 60192 
United States 
800-527-9948 
847-851-1824
Visit this company's website

Facility : # 1 USA


Bentonite[1]
Trade Designation Product Function Max Use
HYDRAUL-EZ® Drilling Fluid
Well Drilling Aid
NA
SUPER GEL-X® Well Drilling Aid NA
VELOXITY-PRO Well Drilling Aid NA
XTRA GEL™ Well Drilling Aid NA

[1] These products are designed to be flushed out prior to using the system for drinking
    water following the manufacturer's use instructions.  The well is to be properly flushed
    and drained until the turbidity of the water is <1 NTU.


Facility : # 8 USA


Polyacrylamide[1] [2] [PC]
Trade Designation Product Function Max Use
ACCU-VIS™ Well Drilling Aid NA
INSTA-PAC® Well Drilling Aid NA
INSTA-VIS™ PLUS Well Drilling Aid NA
SHORE PAC® LIQUID Well Drilling Aid NA

[1] These products are designed to be flushed out prior to using the system for drinking
    water. Before being placed into service, the well is to be properly flushed according to
    the manufacturer's use instructions. Certification of these products is based on the
    well drilling model with the following assumptions: 
    - The amount of well drilling fluid used is 3780 L (1000 U.S. gallons) to which
      the drilling fluid has been added at the manufacturer's recommended level.
    - The aquifer contains 3.1 million liters of water (815,000 gallons) based on a 0.5 acre
      aquifer of 6.1 meter depth (20 ft.) and 25% porosity.
    - The bore hole is 61 meters in total depth (200 ft.), the screen is 6.1 meters in
    length
      (20 ft.), and the bore hole is 25.4 cm. in diameter (10 in.).
    - The amount of well drilling fluid removed from the well during construction is equal
    to 
      the combined volumes of the casing and the screen, plus an additional amount removed 
      through the well disinfection and development (90% removed).
    - This product should not be used in constructing wells in highly porous formations,
    such 
      as cavernous limestone.
[2] This product is designed to be flushed out prior to using the system for drinking water.
    The well is to be properly flushed and drained before being placed into service. This
    product is to be used according to the manufacturer's use instructions.
[PC] Polyacrylamide Products Certified by NSF International comply with 40 CFR 141.111
     requirements for percent monomer and dose.

Sodium Polyacrylate[1] [2]
Trade Designation Product Function Max Use
SUPER THIN™ Well Cleaning Aid
Well Drilling Aid
NA

[1] These products are designed to be flushed out prior to using the system for drinking
    water. Before being placed into service, the well is to be properly flushed according to
    the manufacturer's use instructions. Certification of these products is based on the
    well drilling model with the following assumptions: 
    - The amount of well drilling fluid used is 3780 L (1000 U.S. gallons) to which
      the drilling fluid has been added at the manufacturer's recommended level.
    - The aquifer contains 3.1 million liters of water (815,000 gallons) based on a 0.5 acre
      aquifer of 6.1 meter depth (20 ft.) and 25% porosity.
    - The bore hole is 61 meters in total depth (200 ft.), the screen is 6.1 meters in
    length
      (20 ft.), and the bore hole is 25.4 cm. in diameter (10 in.).
    - The amount of well drilling fluid removed from the well during construction is equal
    to 
      the combined volumes of the casing and the screen, plus an additional amount removed 
      through the well disinfection and development (90% removed).
    - This product should not be used in constructing wells in highly porous formations,
    such 
      as cavernous limestone.
[2] This product is designed to be flushed out prior to using the system for drinking water.
    The well is to be properly flushed and drained before being placed into service. This
    product is to be used according to the manufacturer's use instructions.


Facility : # 9 USA


Miscellaneous Water Supply Products[1] [PC]
Trade Designation Product Function Max Use
ACCU-VIS™ Well Drilling Aid NA
INSTA-PAC® Well Drilling Aid NA

[1] This product is designed to be used off-line following manufacturer’s use instructions.
    The well is to be flushed until the turbidity of the water is < 1 NTU before the system
    may be used for drinking water.
[PC] Polyacrylamide Products Certified by NSF International comply with 40 CFR 141.111
     requirements for percent monomer and dose.


Facility : # 10 USA


Miscellaneous Water Supply Products[1] [WL]
Trade Designation Product Function Max Use
ACCU-VIS™ Well Drilling Aid NA
INSTA-PAC® Well Drilling Aid NA

[1] Certification of these products is based on a well drilling model with the following
    assumptions:
    The amount of well drilling aid used is 3780 liters (1000 U.S. gallons) to which the
    drilling fluid has been added at the manufacturer's recommended level.  The aquifer
    contains 3.1 million liters (815,000 gallons) of water based on a 0.5 acre aquifer of
    6.1 meter (20 foot) depth and 25% porosity.  The bore hole is 61 meters (200 feet) in
    total depth, the screen is 6.1 meters (20 feet) in length, and the bore hole is 25.4
    centimeters (10 inches) in diameter.  The amount of well drilling fluid removed from the
    well during construction is equal to the combined volumes of the casing, the screen, and
    the bore hole annulus around the casing and the screen, plus an additional amount
    removed through the well disinfection and development (90% removed).
[WL] These products are designed to be flushed out prior to using the system for drinking

     water.  The well shall be properly flushed and drained before being placed in service.


Facility : # 14 USA


Sodium Polyacrylate[1]
Trade Designation Product Function Max Use
CLAY CUTTER™ DRY Well Drilling Aid NA

[1] These products are designed to be flushed out prior to using the system for drinking
    water. Before being placed into service, the well is to be properly flushed according to
    the manufacturer's use instructions. Certification of these products is based on the
    well drilling model with the following assumptions: 
    - The amount of well drilling fluid used is 3780 L (1000 U.S. gallons) to which the     
       drilling fluid has been added at the manufacturer's recommended level. 
    - The aquifer contains 3.1 million liters of water (815,000 gallons) based on a 0.5 acre
       aquifer of 6.1 meter depth (20 ft.) and 25% porosity. 
    - The bore hole is 61 meters in total depth (200 ft.), the screen is 6.1 meters in
    length   (20 ft.), and the bore hole is 25.4 cm. in diameter (10 in.). 
    - The amount of well drilling fluid removed from the well during construction is equal
    to   the combined volumes of the casing and the screen, plus an additional amount
    removed      through the well disinfection and development (90% removed). 
    - This product should not be used in constructing wells in highly porous formations,
    such   as cavernous limestone.



 
Chameleon Industries, Inc. 
P.O. Box 853027
Mesquite, TX 75185-3027 
United States 
903-874-9005

Facility : # 2 USA


Polyacrylamide [PC]
Trade Designation Product Function Max Use
CI1066BPWG[1] Well Drilling Aid NA
CI1066PWG[1] Well Drilling Aid NA

[1] This product is designed to be flushed out prior to using the system for drinking water.
     The well is to be properly flushed and drained before being placed into service.  This
    product is to be used according to the manufacturer's use instructions.
[PC] Polyacrylamide Products Certified by NSF International comply with 40 CFR 141.111
     requirements for percent monomer and dose.



 
E&E Chemical and Service Co., LLC 
2631 Little Country Road
Parrish, FL 34219 
United States 
941-776-8798

Facility : Houston, TX


Miscellaneous Water Supply Products[1]
Trade Designation Product Function Max Use
DRILPLEX HDD Well Drilling Aid NA

[1] This product is designed to be flushed out prior to using the system for drinking water.
    Before being placed into service, the well is to be properly flushed according to the
    manufacturer's use instructions.  Certification of this product is based on the well
    drilling model with the following assumptions: 
    - The amount of well drilling fluid used is 3780 L (1000 U.S. gallons) to which the
    drilling fluid has been added at the manufacturer's recommended level. 
    - The aquifer contains 3.1 million liters of water (815,000 gallons) based on a 0.5 acre
    aquifer of 6.1 meter depth (20 ft.) and 25% porosity. 
    - The bore hole is 61 meters in total depth (200 ft.), the screen is 6.1 meters in
    length (20 ft.), and the bore hole is 25.4 cm. in diameter (10 in.). 
    - The amount of well drilling fluid removed from the well during construction is equal
    to the combined volumes of the casing and the screen, plus an additional amount removed
    through the well disinfection and development (90% removed).



 
Economy Mud Products Co. 
435 East Anderson Road
P.O. Box 450246 
Houston, TX 77245-0246 
United States 
713-723-8416

Facility : # 1 USA


Bentonite [WL]
Trade Designation Product Function Max Use
Economy Gel Well Drilling Aid NA
Poly Gel®[1] Well Drilling Aid NA

[1] Prior to using the system for drinking water, the well is to be properly flushed until
    the turbidity of the water is <1 NTU.
[WL] These products are designed to be flushed out prior to using the system for drinking

     water.  The well shall be properly flushed and drained before being placed in service.


Facility : # 2 USA


Bentonite[WS]
Trade Designation Product Function Max Use
Econoplug Coarse Well Drilling Aid NA
Econoplug Medium Well Drilling Aid NA
Econoplug No. 16 Well Drilling Aid NA
Econoplug No. 8 Well Drilling Aid NA

[WS] The well shall be properly flushed and drained before being placed in service.



Fort Bend Services 
13303 Redfish Lane
Stafford, TX 77477 
United States 
800-933-3677 

Facility : # 7 USA


Polyacrylamide [PC]
Trade Designation Product Function Max Use
FBS-1503[1] Well Drilling Aid NA

[1] These products are designed to be flushed out prior to using the system for drinking
    water.  Before being placed in service, the well is to be properly flushed according to
    the manufacturer's use instructions.
    Certification of these products is based on a well drilling model with the following
    assumptions:
    The amount of well drilling fluid used is 3780 L (1000 U.S. gallons) to which the
    drilling fluid has been added at the manufacturer's recommended level.  The aquifer
    contains 3.1 million liters of water (815,000 gallons) based on a 0.5 acre aquifer of
    6.1 meter depth (20 ft.) and 25% porosity.  The bore hole is 61 meters in total depth
    (200 ft.), the screen is 6.1 meters in length (20 ft.), and the bore hole is 25.4 cm in
    construction is equal to the combined volumes of the casing, the screen, and the bore
    hole annuals around the casing and the screen, plus an additional amount removed through
    the well disinfection and development (90% removed).
    These products should not be used in constructing wells in highly porous formations such
    as cavernous limestone.
[PC] Polyacrylamide Products Certified by NSF International comply with 40 CFR 141.111
     requirements for percent monomer and dose.



 
Halliburton Energy Services, Inc. 
3000 North Sam Houston Parkway East
Houston, TX 77032 
United States 
281-871-5320

Facility : # 5 USA


Polyacrylamide[1] [PC]
Trade Designation Product Function Max Use
EZ MUD DP GOLD Well Drilling Aid NA
IDP-567A Well Drilling Aid NA
IDP-620 Well Drilling Aid NA
IDP-623 Well Drilling Aid NA
POLYBORE Well Drilling Aid NA
QUIK-MUD GOLD Well Drilling Aid NA

[1] These products are designed to be flushed out prior to using the system for drinking
    water. Before being placed into service, the well is to be properly flushed according to
    the manufacturer's use instructions. Certification of these products is based on the
    well drilling model with the following assumptions:
         - The amount of well drilling fluid used is 3780 L (1000 U.S. gallons) to which the
           drilling fluid has been added at the manufacturer's recommended level.
         - The aquifer contains 3.1 million liters of water (815,000 gallons) based on a 0.5
           acre aquifer of 6.1 meter depth (20 ft.) and 25% porosity.
         - The bore hole is 61 meters in total depth (200 ft.), the screen is 6.1 meters in
           length (20 ft.), and the bore hole is 25.4 cm. in diameter (10 in.).
         - The amount of well drilling fluid removed from the well during construction is
           equal to the combined volumes of the casing and the screen, plus an additional
           amount removed through the well disinfection and development (90% removed).
         - This product should not be used in constructing wells in highly porous
    formations,
           such as cavernous limestone.
[PC] Polyacrylamide Products Certified by NSF International comply with 40 CFR 141.111
     requirements for percent monomer and dose.



 
Halliburton Energy Services, Inc., Baroid PSL 
3000 North Sam Houston Parkway East
Houston, TX 77032 
United States 
800-735-6075 
281-871-4612
Visit this company's website

Facility : Belle Fourche, SD


Bentonite[1]
Trade Designation Product Function Max Use
IDP-512 Well Drilling Aid NA
QUIK-BORE Well Drilling Aid NA

[1] This product is designed to be used off-line following manufacturer's use instructions.
    The well is to be flushed until the turbidity of the water is < 1 NTU before the system
    may be used for drinking water.

NOTE: Only Listed products bearing the NSF Mark are NSF Certified.

Facility : Rosenberg, TX


Miscellaneous Water Supply Products
Trade Designation Product Function Max Use
QUIK-TROL® Well Drilling Aid NA
QUIK-TROL® GOLD[3] Well Drilling Aid NA
QUIK-TROL® GOLD LV[3] Well Drilling Aid NA
QUIK-TROL® LV Well Drilling Aid NA

[1] Certification of this product is based on a well drilling model using assumptions staed
    in NSF/ANSI Standard 60, Section 8 for well drilling foamers.
[2] This product is designed to be used off-line and flushed out prior to using the system
    for drinking water, following manufacturer's use instructions.
[3] This product is designed to be used off-line following manufacturer's use instructions.
    The well is to be flushed until the turbidity of the water is < 1 NTU before the system
    may be used for drinking water.

Polyacrylamide [PC]
Trade Designation Product Function Max Use
EZ-MUD GOLD[4] [PC] [WL] Well Drilling Aid NA
EZ-MUD®[4] [PC] [WL] Well Drilling Aid NA
EZ-MUD® DP[4] [PC] [WL] Well Drilling Aid NA
EZ-MUD® PLUS[4] [5] [PC] [WL] Well Drilling Aid NA
POLY-BORE™[4] [PC] [WL] Well Drilling Aid NA

[4] Certification of these products is based on the well drilling model with the following
    assumptions:
    - The amount of well drilling fluid used is 3780 L(1000 U.S.gallons) to which the       
       drilling fluid has been added at the manufacturer's recommended level.
    - The aquifer contains 3.1 million liters of water (815,000 gallons) based on a 0.5 acre
       aquifer of 6.1 meter depth (20 ft.) and 25% porosity.
    - The bore hole is 61 meters in total depth (200 ft.), and the bore hole is 25.4 cm. in 
       diameter (10 in.).
    - The amount of well drilling fluid removed from the well during construction is equal
    to   the combined volumes of the casing and the screen, plus an additional amount
    removed      throught the well disinfection and development (90% removed).
    - This product should not be used in constructing wells in highly porous formations,    
       such as cavernous limestone.
[5] This product is designed for the treatment of surface water before it enters the water
    treatment facility.
[PC] Polyacrylamide Products Certified by NSF International comply with 40 CFR 141.111
     requirements for percent monomer and dose.
[PC] Polyacrylamide Products Certified by NSF International comply with 40 CFR 141.111
     requirements for percent monomer and dose.
[WL] These products are designed to be flushed out prior to using the system for drinking

     water.  The well shall be properly flushed and drained before being placed in service.


Facility : Aurora, UT


Bentonite
Trade Designation Product Function Max Use
AQUAGEL©[1] Well Drilling Aid NA
QUIK-GEL©[1] Well Drilling Aid NA
QUIK-GEL® Gold[1] Well Drilling Aid NA

[1] The well is to be properly flushed until the turbidity of the water is <1 NTU.



 
Halliburton Energy Services, Inc., Baroid PSL 
3000 North Sam Houston Parkway East
Houston, TX 77032 
United States 
800-735-6075 
281-871-4612
Visit this company's website

Facility : # 2 USA


Polyacrylamide [PC]
Trade Designation Product Function Max Use
EZ MUD®[1] [2] Well Drilling Aid NA
EZ MUD® PLUS[1] [2] Well Drilling Aid NA
EZ-MUD® DP[1] [2] Well Drilling Aid NA
FUSE-IT Well Drilling Aid NA
QUIK MUD® D-50[1] [2] Well Drilling Aid NA
QUIK MUD® GOLD[1] [2] Well Drilling Aid NA

[1] This product is designed to be flushed out prior to using the system for drinking water.
     The well is to be properly flushed and drained before being placed into service.  This
    product is to be used according to the manufacturer's use instructions.
[2] These products are designed to be flushed out prior to using the system for drinking
    water. Before being placed into service, the well is to be properly flushed according to
    the manufacturer's use instructions. Certification of these products is based on the
    well drilling model with the following assumptions: 
    - The amount of well drilling fluid used is 3780 L (1000 U.S. gallons) to which
      the drilling fluid has been added at the manufacturer's recommended level.
    - The aquifer contains 3.1 million liters of water (815,000 gallons) based on a 0.5 acre
      aquifer of 6.1 meter depth (20 ft.) and 25% porosity.
    - The bore hole is 61 meters in total depth (200 ft.), the screen is 6.1 meters in
    length
      (20 ft.), and the bore hole is 25.4 cm. in diameter (10 in.).
    - The amount of well drilling fluid removed from the well during construction is equal
    to 
      the combined volumes of the casing and the screen, plus an additional amount removed 
      through the well disinfection and development (90% removed).
    - This product should not be used in constructing wells in highly porous formations,
    such
      as cavernous limestone.
    
[PC] Polyacrylamide Products Certified by NSF International comply with 40 CFR 141.111
     requirements for percent monomer and dose.

Polyamines [PY]
Trade Designation Product Function Max Use
SYSTEM-FLOC 360[2] Well Drilling Aid NA

[2] These products are designed to be flushed out prior to using the system for drinking
    water. Before being placed into service, the well is to be properly flushed according to
    the manufacturer's use instructions. Certification of these products is based on the
    well drilling model with the following assumptions: 
    - The amount of well drilling fluid used is 3780 L (1000 U.S. gallons) to which
      the drilling fluid has been added at the manufacturer's recommended level.
    - The aquifer contains 3.1 million liters of water (815,000 gallons) based on a 0.5 acre
      aquifer of 6.1 meter depth (20 ft.) and 25% porosity.
    - The bore hole is 61 meters in total depth (200 ft.), the screen is 6.1 meters in
    length
      (20 ft.), and the bore hole is 25.4 cm. in diameter (10 in.).
    - The amount of well drilling fluid removed from the well during construction is equal
    to 
      the combined volumes of the casing and the screen, plus an additional amount removed 
      through the well disinfection and development (90% removed).
    - This product should not be used in constructing wells in highly porous formations,
    such
      as cavernous limestone.
    
[PY] Polyamines Certified by NSF International comply with 40 CFR 141.111 requirements for
     percent monomer and dose.

Sodium Polyacrylate[1] [2]
Trade Designation Product Function Max Use
Baroid AQUA CLEAR PFD Well Cleaning Aid
Well Drilling Aid
NA

[1] This product is designed to be flushed out prior to using the system for drinking water.
     The well is to be properly flushed and drained before being placed into service.  This
    product is to be used according to the manufacturer's use instructions.
[2] These products are designed to be flushed out prior to using the system for drinking
    water. Before being placed into service, the well is to be properly flushed according to
    the manufacturer's use instructions. Certification of these products is based on the
    well drilling model with the following assumptions: 
    - The amount of well drilling fluid used is 3780 L (1000 U.S. gallons) to which
      the drilling fluid has been added at the manufacturer's recommended level.
    - The aquifer contains 3.1 million liters of water (815,000 gallons) based on a 0.5 acre
      aquifer of 6.1 meter depth (20 ft.) and 25% porosity.
    - The bore hole is 61 meters in total depth (200 ft.), the screen is 6.1 meters in
    length
      (20 ft.), and the bore hole is 25.4 cm. in diameter (10 in.).
    - The amount of well drilling fluid removed from the well during construction is equal
    to 
      the combined volumes of the casing and the screen, plus an additional amount removed 
      through the well disinfection and development (90% removed).
    - This product should not be used in constructing wells in highly porous formations,
    such
      as cavernous limestone.
    


Facility : # 12 USA


Polyamines [PY]
Trade Designation Product Function Max Use
SYSTEM-FLOC 360[1] Well Drilling Aid NA

[1] These products are designed to be flushed out prior to using the system for drinking
    water. Before being placed into service, the well is to be properly flushed according to
    the manufacturer's use instructions. Certification of these products is based on the
    well drilling model with the following assumptions: 
    - The amount of well drilling fluid used is 3780 L (1000 U.S. gallons) to which
      the drilling fluid has been added at the manufacturer's recommended level.
    - The aquifer contains 3.1 million liters of water (815,000 gallons) based on a 0.5 acre
      aquifer of 6.1 meter depth (20 ft.) and 25% porosity.
    - The bore hole is 61 meters in total depth (200 ft.), the screen is 6.1 meters in
    length
      (20 ft.), and the bore hole is 25.4 cm. in diameter (10 in.).
    - The amount of well drilling fluid removed from the well during construction is equal
    to 
      the combined volumes of the casing and the screen, plus an additional amount removed 
      through the well disinfection and development (90% removed).
    - This product should not be used in constructing wells in highly porous formations,
    such
      as cavernous limestone.
[PY] Polyamines Certified by NSF International comply with 40 CFR 141.111 requirements for
     percent monomer and dose.



 
Halliburton Energy Services, Inc., Baroid PSL 
3000 North Sam Houston Parkway East
Houston, TX 77032 
United States 
800-735-6075 
281-871-4612
Visit this company's website

Facility : # 6 USA


Miscellaneous Water Supply Products[1] [2]
Trade Designation Product Function Max Use
QUIK-TROL® GOLD (50 lb bags) Well Drilling Aid NA
QUIK-TROL® GOLD LV Well Drilling Aid NA

[1] This product is designed to be used off-line and flushed out prior to using the system
    for drinking water, following manufacturer's use instructions.
[2] The well is to be properly flushed until the turbidity of the water is <1 NTU.



 
Hawkins Water Treatment Group 
2381 Rosegate
Roseville, MN 55113 
United States 
612-617-8603

Facility : # 5 USA


Miscellaneous Water Supply Products
Trade Designation Product Function Max Use
WT-3715-P Well Cleaning Aid
Well Drilling Aid
NA

Polyacrylamide [PC]
Trade Designation Product Function Max Use
WT-3051-P Well Drilling Aid NA
WT-3052-P Well Drilling Aid NA
WT-3272-P[1] [2] Well Drilling Aid NA
WT-3805-P Well Drilling Aid NA
WT-3806-P[1] [2] Well Drilling Aid NA
WT-3882-P[1] [2] Well Drilling Aid NA
WT-3989-P Well Drilling Aid NA

[1] This product is designed to be flushed out prior to using the system for drinking water.
     The well is to be properly flushed and drained before being placed into service.  This
    product is to be used according to the manufacturer's use instructions.
[2] These products are designed to be flushed out prior to using the system for drinking
    water. Before being placed into service, the well is to be properly flushed according to
    the manufacturer's use instructions. Certification of these products is based on the
    well drilling model with the following assumptions: 
    - The amount of well drilling fluid used is 3780 L (1000 U.S. gallons) to which
      the drilling fluid has been added at the manufacturer's recommended level.
    - The aquifer contains 3.1 million liters of water (815,000 gallons) based on a 0.5 acre
      aquifer of 6.1 meter depth (20 ft.) and 25% porosity.
    - The bore hole is 61 meters in total depth (200 ft.), the screen is 6.1 meters in
    length
      (20 ft.), and the bore hole is 25.4 cm. in diameter (10 in.).
    - The amount of well drilling fluid removed from the well during construction is equal
    to 
      the combined volumes of the casing and the screen, plus an additional amount removed 
      through the well disinfection and development (90% removed).
    - This product should not be used in constructing wells in highly porous formations,
    such
      as cavernous limestone.
[PC] Polyacrylamide Products Certified by NSF International comply with 40 CFR 141.111
     requirements for percent monomer and dose.



 
Hychem, Inc. 
10014 North Dale Mabry Highway
Suite 213 
Tampa, FL 33618 
United States 
813-963-6214
Visit this company's website

Facility : # 1 USA


Polyacrylamide [PC]
Trade Designation Product Function Max Use
Hyperdrill® AD 859[1] Well Drilling Aid NA
Hyperdrill® AE 853[1] Well Drilling Aid NA
Hyperdrill® AE 856[1] Well Drilling Aid NA

[1] These products are designed to be flushed out prior to using the system for drinking
    water. Before being placed into service, the well is to be properly flushed according to
    the manufacturer's use instructions. Certification of these products is based on the
    well drilling model with the following assumptions: 
    - The amount of well drilling fluid used is 3780 L (1000 U.S. gallons) to which
      the drilling fluid has been added at the manufacturer's recommended level. 
    - The aquifer contains 3.1 million liters of water (815,000 gallons) based on a 0.5 acre
      aquifer of 6.1 meter depth (20 ft.) and 25% porosity.
    - The bore hole is 61 meters in total depth (200 ft.), the screen is 6.1 meters in
    length
      (20 ft.), and the bore hole is 25.4 cm. in diameter (10 in.).
    - The amount of well drilling fluid removed from the well during construction is equal
    to 
      the combined volumes of the casing and the screen, plus an additional amount removed 
      through the well disinfection and development (90% removed).
    - This product should not be used in constructing wells in highly porous formations,
    such 
      as cavernous limestone.
[PC] Polyacrylamide Products Certified by NSF International comply with 40 CFR 141.111
     requirements for percent monomer and dose.

Sodium Polyacrylate[1]
Trade Designation Product Function Max Use
Hyperdrill DF 2010 Well Cleaning Aid
Well Drilling Aid
NA

[1] These products are designed to be flushed out prior to using the system for drinking
    water. Before being placed into service, the well is to be properly flushed according to
    the manufacturer's use instructions. Certification of these products is based on the
    well drilling model with the following assumptions: 
    - The amount of well drilling fluid used is 3780 L (1000 U.S. gallons) to which
      the drilling fluid has been added at the manufacturer's recommended level. 
    - The aquifer contains 3.1 million liters of water (815,000 gallons) based on a 0.5 acre
      aquifer of 6.1 meter depth (20 ft.) and 25% porosity.
    - The bore hole is 61 meters in total depth (200 ft.), the screen is 6.1 meters in
    length
      (20 ft.), and the bore hole is 25.4 cm. in diameter (10 in.).
    - The amount of well drilling fluid removed from the well during construction is equal
    to 
      the combined volumes of the casing and the screen, plus an additional amount removed 
      through the well disinfection and development (90% removed).
    - This product should not be used in constructing wells in highly porous formations,
    such 
      as cavernous limestone.



 
Hydro Resources - Rocky Mountain, Inc. 
13027 County Road 18
Unit C 
Fort Lupton, CO 80621 
United States 
303-857-4171

Facility : # 1 USA


Polyacrylamide[1] [PC]
Trade Designation Product Function Max Use
HYDRO VIS 30 Well Drilling Aid NA

[1] These products are designed to be flushed out prior to using the system for drinking
    water. Before being placed into service, the well is to be properly flushed according to
    the manufacturer's use instructions. Certification of these products is based on the
    well drilling model with the following assumptions:
         - The amount of well drilling fluid used is 3780 L (1000 U.S. gallons) to which the
           drilling fluid has been added at the manufacturer's recommended level.
         - The aquifer contains 3.1 million liters of water (815,000 gallons) based on a 0.5
           acre aquifer of 6.1 meter depth (20 ft.) and 25% porosity.
         - The bore hole is 61 meters in total depth (200 ft.), the screen is 6.1 meters in
           length (20 ft.), and the bore hole is 25.4 cm. in diameter (10 in.).
         - The amount of well drilling fluid removed from the well during construction is
           equal to the combined volumes of the casing and the screen, plus an additional
           amount removed through the well disinfection and development (90% removed).
         - This product should not be used in constructing wells in highly porous
    formations,
           such as cavernous limestone.
[PC] Polyacrylamide Products Certified by NSF International comply with 40 CFR 141.111
     requirements for percent monomer and dose.



 
Hydro Resources – Rocky Mountain, Inc. 
13027 County Road 18
Fort Lupton, CO 80621 
United States 
303-857-4171

Facility : # 2 USA


Miscellaneous Water Supply Products [WL]
Trade Designation Product Function Max Use
Hydrothin Well Drilling Aid NA
Hydrovis-50[1] Well Drilling Aid NA

[1] Certification of these products is based on a well drilling model with the following
    assumptions:
    The amount of well drilling aid used is 3780 liters (1000 U.S. gallons) to which the
    drilling fluid has been added at the manufacturer's recommended level.  The aquifer
    contains 3.1 million liters (815,000 gallons) of water based on a 0.5 acre aquifer of
    6.1 meter (20 foot) depth and 25% porosity.  The bore hole is 61 meters (200 feet) in
    total depth, the screen is 6.1 meters (20 feet) in length, and the bore hole is 25.4
    centimeters (10 inches) in diameter.  The amount of well drilling fluid removed from the
    well during construction is equal to the combined volumes of the casing, the screen, and
    the bore hole annulus around the casing and the screen, plus an additional amount
    removed through the well disinfection and development (90% removed).  This product
    should not be used in constructing wells in highly porous formations, such as cavernous
    limestone.
[WL] These products are designed to be flushed out prior to using the system for drinking

     water.  The well shall be properly flushed and drained before being placed in service.


Facility : # 3 USA


Miscellaneous Water Supply Products [PC]
Trade Designation Product Function Max Use
Hydrothin[1] Well Drilling Aid NA
Hydrovis-50[1] Well Drilling Aid NA

[1] This product is designed to be used off-line following manufacturer’s use instructions.
    The well is to be flushed until the turbidity of the water is < 1 NTU before the system
    may be used for drinking water.
[PC] Polyacrylamide Products Certified by NSF International comply with 40 CFR 141.111
     requirements for percent monomer and dose.



 
KED Group, Inc. 
10042 Lone Tree Lane
Orlando, FL 32836 
United States 
407-876-4021

Facility : # 1 USA


Miscellaneous Water Supply Products
Trade Designation Product Function Max Use
FS018 PWG DA[1] [2] Well Drilling Aid
Well Cleaning Aid
NA

[1] This product is designed to be flushed out prior to using the system for drinking water.
     The well is to be properly flushed and drained before being placed into service.  This
    product is to be used according to the manufacturer's use instructions.
[2] These products are designed to be flushed out prior to using the system for drinking
    water. Before being placed into service, the well is to be properly flushed according to
    the manufacturer's use instructions. Certification of these products is based on the
    well drilling model with the following assumptions: 
    - The amount of well drilling fluid used is 3780 L (1000 U.S. gallons) to which
      the drilling fluid has been added at the manufacturer's recommended level.
    - The aquifer contains 3.1 million liters of water (815,000 gallons) based on a 0.5 acre
      aquifer of 6.1 meter depth (20 ft.) and 25% porosity.
    - The bore hole is 61 meters in total depth (200 ft.), the screen is 6.1 meters in
    length
      (20 ft.), and the bore hole is 25.4 cm. in diameter (10 in.).
    - The amount of well drilling fluid removed from the well during construction is equal
    to 
      the combined volumes of the casing and the screen, plus an additional amount removed 
      through the well disinfection and development (90% removed).
    - This product should not be used in constructing wells in highly porous formations,
    such
      as cavernous limestone.

Polyacrylamide [PC]
Trade Designation Product Function Max Use
EK 53 PWG-1-2-WDA[1] [2] Well Drilling Aid 3
EK533 PWG-B30 1-2-WDA[1] [2] Well Drilling Aid 3
EKF 533 PWG-1-2-WDA[1] [2] Well Drilling Aid 3
EKF 533-A-PWG-1-2-WDA[1] [2] Well Drilling Aid NA
PA 120 SHU PWG[2] Well Drilling Aid NA
PA 120 VLM PWG[2] Well Drilling Aid NA
PA 130 BPM-1-2PWG-WDA[1] [2] Well Drilling Aid NA
PA 130 PWG W10%SALT-2-WDA[2] [PY] Well Drilling Aid NA
PA 130 PWG-1-2-WDA[1] [2] Well Drilling Aid NA
PA 130 VLM PWG-2-WDA[2] [PY] Well Drilling Aid NA
PA 140 PWG-2[2] Well Drilling Aid NA
PA120SHU PWG WDA[2] [PY] Well Drilling Aid NA
PA120VLM PWG WDA[2] [PY] Well Drilling Aid NA

[1] This product is designed to be flushed out prior to using the system for drinking water.
     The well is to be properly flushed and drained before being placed into service.  This
    product is to be used according to the manufacturer's use instructions.
[2] These products are designed to be flushed out prior to using the system for drinking
    water. Before being placed into service, the well is to be properly flushed according to
    the manufacturer's use instructions. Certification of these products is based on the
    well drilling model with the following assumptions: 
    - The amount of well drilling fluid used is 3780 L (1000 U.S. gallons) to which
      the drilling fluid has been added at the manufacturer's recommended level.
    - The aquifer contains 3.1 million liters of water (815,000 gallons) based on a 0.5 acre
      aquifer of 6.1 meter depth (20 ft.) and 25% porosity.
    - The bore hole is 61 meters in total depth (200 ft.), the screen is 6.1 meters in
    length
      (20 ft.), and the bore hole is 25.4 cm. in diameter (10 in.).
    - The amount of well drilling fluid removed from the well during construction is equal
    to 
      the combined volumes of the casing and the screen, plus an additional amount removed 
      through the well disinfection and development (90% removed).
    - This product should not be used in constructing wells in highly porous formations,
    such
      as cavernous limestone.
[PC] Polyacrylamide Products Certified by NSF International comply with 40 CFR 141.111
     requirements for percent monomer and dose.
[PY] Polyamines Certified by NSF International comply with 40 CFR 141.111 requirements for
     percent monomer and dose.

Sodium Polyacrylate
Trade Designation Product Function Max Use
FS 000 PWG WDA Well Cleaning Aid
Well Drilling Aid
NA



 
Kemira Chemicals, Inc. 
1000 Parkwood Circle
Suite 500 
Atlanta, GA 30339 
United States 
770-422-1250
Visit this company's website

Facility : Aberdeen, MS


Polyacrylamide [PC]
Trade Designation Product Function Max Use
Sedifloc 7030HHM[1] Well Drilling Aid NA

[1] These products are designed to be flushed out prior to using the system for drinking
    water. Before being placed into service, the well is to be properly flushed according to
    the manufacturer's use instructions. Certification of these products is based on the
    well drilling model with the following assumptions:
    - The amount of well drilling fluid used is 3780 L (1000 U.S. gallons) to which the
    drilling fluid has been added at the manufacturer's recommended level. 
    - The aquifer contains 3.1 million liters of water (815,000 gallons) based on a 0.5 acre
    aquifer of 6.1 meter depth (20 ft.) and 25% porosity. 
    - The bore hole is 61 meters in total depth (200 ft.), the screen is 6.1 meters in
    length (20 ft.), and the bore hole is 25.4 cm in diameter (10 in.).
    - The amount of well drilling fluid removed from the well during construction is equal
    to the combined volumes of the casing and the screen, plus an additional amount removed
    through the well disinfection and development (90% removed). 
    - This product should not be used in constructing wells in highly porous formations,
    such as cavernous limestone. 
    
[PC] Polyacrylamide Products Certified by NSF International comply with 40 CFR 141.111
     requirements for percent monomer and dose.



 
Kemira Water Solutions, Inc. 
316 Bartow Municipal Airport
Bartow, FL 33830 
United States 
863-533-5990
Visit this company's website

Facility : # 1 LW USA


Polyacrylamide [PC]
Trade Designation Product Function Max Use
Cyanatrol 930[1] Well Drilling Aid NA
Cydril 5300[1] Well Drilling Aid NA
Cydril 5310[1] Well Drilling Aid NA
KemDrill 5300[1] Well Drilling Aid NA
KemDrill A1355[1] Well Drilling Aid NA
KemDrill A1363[1] Well Drilling Aid NA
KemFlow A-4355[1] Well Drilling Aid NA
KemFlow A-4365[1] Well Drilling Aid NA
Superfloc A-1820[1] Well Drilling Aid NA
Superfloc A-1883 LMW[1] Well Drilling Aid NA

[1] These products are designed to be flushed out prior to using the system for drinking
    water.  Before being placed into service, the well is to be properly flushed according
    to the manufacturer's use instructions.  Certification of these products is based on the
    well drilling model with the following assumptions:
    - The amount of well drilling fluid used is 3780 L (1000 U.S. gallons) to which 
      the drilling fluid has been added at 7.6 L.
    - The aquifer contains 3.1 million liters of water (815,000 gallons) based on a 0.5 acre
      aquifer of 6.1 meter depth (20 ft.) and 25% porosity.
    - The bore hole is 61 meters in total depth (200 ft.), the screen is 6.1 meters in
    length
      (20 ft.), and the bore hole is 25.4 cm.  in diameter (10 in.).
    - The amount of well drilling fluid removed from the well during construction is equal
    to
      the combined volumes of the casing and the screen, plus an additional amount removed
[PC] Polyacrylamide Products Certified by NSF International comply with 40 CFR 141.111
     requirements for percent monomer and dose.


Facility : #1 LW Canada


Polyacrylamide [PC]
Trade Designation Product Function Max Use
Cyanatrol 930[1] Well Drilling Aid NA
Cydril 5300[1] Well Drilling Aid NA
Cydril 5310[1] Well Drilling Aid NA
KemDrill 5300[1] Well Drilling Aid NA
KemDrill A1355[1] Well Drilling Aid NA
KemDrill A1363[1] Well Drilling Aid NA
KemEflow A-4355[1] Well Drilling Aid NA
KemEflow A-4363[1] Well Drilling Aid NA
KemEflow A-4365[1] Well Drilling Aid NA
Superfloc 5300[1] Well Drilling Aid NA
Superfloc A-1820[1] Well Drilling Aid NA
Superfloc A-1883 LMW[1] Well Drilling Aid NA

[1] These products are designed to be flushed our prior to using the system for drinking
    water. Before being places into service, the well is to be properly flushed according to
    the manufacturer's use instructions. Certification of these products is based on the
    well drilling model with the following assumptions: 
    - The amount of well drilling fluid used 3780 L (1000 U.S. gallons) to which the
    drilling fluid has been added at the manufacturer’s recommended level. 
    - The aquifer contains 3.1 million liters of water (815,000 gallons) based on a 0.5 acre
    aquifer of 6.1 meter depth (20 ft.) and 25% porosity. 
    -The bore hole is 61 meters in total depth (200 ft.), the screen is 6.1 meters in length
    (20 ft.), and the bore hole is 25.4 cm in diameter (10 in.).
    -The amount of well drilling fluid removed from the well during construction is equal to
    the combined volumes of the casing and the screen, plus an additional amount removed
    through the well disinfection and development (90% removed)
    -This product should not be used in constructing wells in highly porous formations, such
    as cavernous limestone. 
    
[PC] Polyacrylamide Products Certified by NSF International comply with 40 CFR 141.111
     requirements for percent monomer and dose.


Facility : # 3 USA


Polyacrylamide [PC]
Trade Designation Product Function Max Use
Cyanatrol 930[1] [2] [3] Well Drilling Aid NA
Cydril 5300[1] [2] [3] Well Drilling Aid NA
Cydril 5310[1] [2] [3] Well Drilling Aid NA
KemDrill 5300[1] [2] [3] Well Drilling Aid NA
KemDrill A1355[1] [2] [3] Well Drilling Aid NA
KemDrill A1363[1] [2] [3] Well Drilling Aid NA
KemFlow A-4355[1] [2] [3] Well Drilling Aid NA
KemFlow A-4363[1] [2] [3] Well Drilling Aid NA
KemFlow A-4365[1] [2] [3] Well Drilling Aid NA
Superfloc 5300[1] [2] [3] Well Drilling Aid NA
Superfloc A-1820[1] [2] [3] Well Drilling Aid NA
Superfloc A-1883LMW[1] [2] [3] Well Drilling Aid NA

[1] These products should not be used in constructing wells in highly porous formations such
    as cavernous limestone.
[2] These products are designed to be flushed out prior to using the system for drinking
    water.  Before being placed in service, the well is to be properly flushed according to
    the manufacturer's use instructions.
[3] Certification of these products is based on a well drilling model with the following
    assumptions:
    The amount of well drilling fluid used is 3780 L (1000 U.S. gallons) to which the
    drilling fluid has been added at the manufacturer's recommended level.  The aquifer
    contains 3.1 million liters of water (815,000 gallons) based on a 0.5 acre aquifer of
    6.1 meter depth (20 ft.) and 25% porosity.  The bore hole is 61 meters in total depth
    (200 ft.), the screen is 6.1 meters in length (20 ft.), and the bore hole is 25.4 cm in
    diameter (10 in.).  The amount of well drilling fluid removed from the well during
    construction is equal to the combined volumes of the casing, the screen, and the bore
    hole annuals around the casing and the screen, plus an additional amount removed through
    the well disinfection and development (90% removed).
[PC] Polyacrylamide Products Certified by NSF International comply with 40 CFR 141.111
     requirements for percent monomer and dose.


Facility : # 4 USA


Polyacrylamide [PC]
Trade Designation Product Function Max Use
Cydril 5310[1] [2] Well Drilling Aid NA
KemDrill A1355[1] [2] Well Drilling Aid NA
KemEflow A-4355 Well Drilling Aid NA
KemFlow A-4355[1] [2] Well Drilling Aid NA
Superfloc A-1883LMW[1] [2] Well Drilling Aid NA
Superfloc A1820[1] [2] Well Drilling Aid NA

[1] These products are designed to be flushed out prior to using the system for drinking
    water.  Before being placed in service, the well is to be properly flushed according to
    the manufacturer's use instructions.
[2] Certification of these products is based on a well drilling model with the following
    assumptions:
    The amount of well drilling fluid used is 3780 L (1000 U.S. gallons) to which the
    drilling fluid has been added at the manufacturer's recommended level.  The aquifer
    contains 3.1 million liters of water (815,000 gallons) based on a 0.5 acre aquifer of
    6.1 meter depth (20 ft.) and 25% porosity.  The bore hole is 61 meters in total depth
    (200 ft.), the screen is 6.1 meters in length (20 ft.), and the bore hole is 25.4 cm in
    diameter (10 in.).  The amount of well drilling fluid removed from the well during
    construction is equal to the combined volumes of the casing, the screen, and the bore
    hole annuals around the casing and the screen, plus an additional amount removed through
    the well disinfection and development (90% removed).
[PC] Polyacrylamide Products Certified by NSF International comply with 40 CFR 141.111
     requirements for percent monomer and dose.


Facility : # 5 LW USA


Polyacrylamide [PC]
Trade Designation Product Function Max Use
Cyanatrol 930[1] Well Drilling Aid NA
Cydril 5300[1] Well Drilling Aid NA
Cydril 5310[1] Well Drilling Aid NA
KemDrill 5300[1] Well Drilling Aid NA
KemDrill A1355[1] Well Drilling Aid NA
KemDrill A1363[1] Well Drilling Aid NA
KemFlow A-4365[1] Well Drilling Aid NA
Superfloc 5300[1] Well Drilling Aid NA
Superfloc A-1820[1] Well Drilling Aid NA
Superfloc A-1883 LMW[1] Well Drilling Aid NA

[1] These products are designed to be flushed out prior to using the system for drinking
    water.  Before being placed into service, the well is to be properly flushed according
    to the manufacturer's use instructions.  Certification of these products is based on the
    well drilling model with the following assumptions:
    - The amount of well drilling fluid used is 3780 L (1000 U.S. gallons) to which 
      the drilling fluid has been added at 7.6 L.
    - The aquifer contains 3.1 million liters of water (815,000 gallons) based on a 0.5 acre
      aquifer of 6.1 meter depth (20 ft.) and 25% porosity.
    - The bore hole is 61 meters in total depth (200 ft.), the screen is 6.1 meters in
    length
      (20 ft.), and the bore hole is 25.4 cm.  in diameter (10 in.).
    - The amount of well drilling fluid removed from the well during construction is equal
    to
      the combined volumes of the casing and the screen, plus an additional amount removed
      through the well disinfection and development (90% removed). 
    These products should not be used in constructing wells in highly porous formations such
    as cavernous limestone.
[PC] Polyacrylamide Products Certified by NSF International comply with 40 CFR 141.111
     requirements for percent monomer and dose.


Facility : # 6 LW USA


Polyacrylamide [PC]
Trade Designation Product Function Max Use
Cyanatrol 930[1] Well Drilling Aid NA
Cydril 5300[1] Well Drilling Aid NA
Cydril 5310[1] Well Drilling Aid NA
KemDrill 5300[1] Well Drilling Aid NA
KemDrill A1355[1] Well Drilling Aid NA
KemDrill A1363[1] Well Drilling Aid NA
KemFlow A-4365[1] Well Drilling Aid NA
Superfloc 5300[1] Well Drilling Aid NA
Superfloc A 1820[1] Well Drilling Aid NA
Superfloc A-1820[1] Well Drilling Aid NA
Superfloc A-1883 LMW[1] Well Drilling Aid NA
Superfloc A-1883LMW[1] Well Drilling Aid NA

[1] These products are designed to be flushed out prior to using the system for drinking
    water.  Before being placed into service, the well is to be properly flushed according
    to the manufacturer's use instructions.  Certification of these products is based on the
    well drilling model with the following assumptions:
    - The amount of well drilling fluid used is 3780 L (1000 U.S. gallons) to which 
      the drilling fluid has been added at 7.6 L.
    - The aquifer contains 3.1 million liters of water (815,000 gallons) based on a 0.5 acre
      aquifer of 6.1 meter depth (20 ft.) and 25% porosity.
    - The bore hole is 61 meters in total depth (200 ft.), the screen is 6.1 meters in
    length
      (20 ft.), and the bore hole is 25.4 cm.  in diameter (10 in.).
    - The amount of well drilling fluid removed from the well during construction is equal
    to
      the combined volumes of the casing and the screen, plus an additional amount removed
      through the well disinfection and development (90% removed). 
    These products should not be used in constructing wells in highly porous formations such
    as cavernous limestone.
[PC] Polyacrylamide Products Certified by NSF International comply with 40 CFR 141.111
     requirements for percent monomer and dose.


Facility : # 11 USA


Polyacrylamide [PC]
Trade Designation Product Function Max Use
Cyanatrol 930[1] Well Drilling Aid NA
Cydril 5300[1] Well Drilling Aid NA
Cydril 5310[1] Well Drilling Aid NA
KemDrill 5300[1] Well Drilling Aid NA
KemDrill A1355[1] Well Drilling Aid NA
KemDrill A1363[1] Well Drilling Aid NA
KemFlow A-4355 Well Drilling Aid NA
KemFlow A-4363 Well Drilling Aid NA
KemFlow A-4365 Well Drilling Aid NA
Superfloc 5300[1] Well Drilling Aid NA
Superfloc A-1820 Flocculant[1] Well Drilling Aid NA
Superfloc A-1883LMW[1] Well Drilling Aid NA

[1] These products are designed to be flushed out prior to using the system for drinking
    water.  Before being placed in service, the well is to be properly flushed according to
    the manufacturer's use instructions.
    Certification of these products is based on a well drilling model with the following
    assumptions:
    The amount of well drilling fluid used is 3780 L (1000 U.S. gallons) to which the
    drilling fluid has been added at the manufacturer's recommended level.  The aquifer
    contains 3.1 million liters of water (815,000 gallons) based on a 0.5 acre aquifer of
    6.1 meter depth (20 ft.) and 25% porosity.  The bore hole is 61 meters in total depth
    (200 ft.), the screen is 6.1 meters in length (20 ft.), and the bore hole is 25.4 cm in
    construction is equal to the combined volumes of the casing, the screen, and the bore
    hole annuals around the casing and the screen, plus an additional amount removed through
    the well disinfection and development (90% removed).
    These products should not be used in constructing wells in highly porous formations such
    as cavernous limestone.
[PC] Polyacrylamide Products Certified by NSF International comply with 40 CFR 141.111
     requirements for percent monomer and dose.



 
Klar Water, Inc. 
P.O. Box 13731
Maumelle, AR 72113 
United States 
501-851-6333

Facility : # 6 LW USA


Polyacrylamide[PC]
Trade Designation Product Function Max Use
PolyKlar E-1330P Well Drilling Aid N/A

[PC] Polyacrylamide Products Certified by NSF International comply with 40 CFR 141.111
     requirements for percent monomer and dose.



 
Lost Circulation Specialists, Inc. 
16202 Surrey Lane
Stagecoach, TX 77355 
United States 
281-252-4243
Visit this company's website

Facility : # 1 USA


Miscellaneous Water Supply Products[1]
Trade Designation Product Function Max Use
Magma Fiber Coarse Well Drilling Aid NA
Magma Fiber Fine Well Drilling Aid NA

[1] These products are designed to be flushed out prior to using the system for drinking
    water. Before being placed in service, the well is to be properly flushed and drained
    according to the manufacturer's use instructions.



 
M-I L.L.C. 
A Schlumberger Company
5950 North Course Drive 
Houston, TX 77072 
United States 
832-295-2747

Facility : # 1 LW USA


Polyacrylamide[1] [PC]
Trade Designation Product Function Max Use
Poly Plus Well Drilling Aid NA

[1] These products are designed to be flushed out prior to using the system for drinking
    water.  Before being placed into service, the well is to be properly flushed according
    to the manufacturer's use instructions.  Certification of these products is based on the
    well drilling model with the following assumptions:
    - The amount of well drilling fluid used is 3780 L (1000 U.S. gallons) to which 
      the drilling fluid has been added at 7.6 L.
    - The aquifer contains 3.1 million liters of water (815,000 gallons) based on a 0.5 acre
      aquifer of 6.1 meter depth (20 ft.) and 25% porosity.
    - The bore hole is 61 meters in total depth (200 ft.), the screen is 6.1 meters in
    length
      (20 ft.), and the bore hole is 25.4 cm.  in diameter (10 in.).
    - The amount of well drilling fluid removed from the well during construction is equal
    to
      the combined volumes of the casing and the screen, plus an additional amount removed
      through the well disinfection and development (90% removed). 
    These products should not be used in constructing wells in highly porous formations such
    as cavernous limestone.
[PC] Polyacrylamide Products Certified by NSF International comply with 40 CFR 141.111
     requirements for percent monomer and dose.


Facility : # 5 LW USA


Polyacrylamide[1] [PC]
Trade Designation Product Function Max Use
Poly Plus Well Drilling Aid NA

[1] These products are designed to be flushed out prior to using the system for drinking
    water.  Before being placed into service, the well is to be properly flushed according
    to the manufacturer's use instructions.  Certification of these products is based on the
    well drilling model with the following assumptions:
    - The amount of well drilling fluid used is 3780 L (1000 U.S. gallons) to which 
      the drilling fluid has been added at 7.6 L.
    - The aquifer contains 3.1 million liters of water (815,000 gallons) based on a 0.5 acre
      aquifer of 6.1 meter depth (20 ft.) and 25% porosity.
    - The bore hole is 61 meters in total depth (200 ft.), the screen is 6.1 meters in
    length
      (20 ft.), and the bore hole is 25.4 cm.  in diameter (10 in.).
    - The amount of well drilling fluid removed from the well during construction is equal
    to
      the combined volumes of the casing and the screen, plus an additional amount removed
      through the well disinfection and development (90% removed). 
    These products should not be used in constructing wells in highly porous formations such
    as cavernous limestone.
[PC] Polyacrylamide Products Certified by NSF International comply with 40 CFR 141.111
     requirements for percent monomer and dose.


Facility : # 6 LW USA


Polyacrylamide[1] [PC]
Trade Designation Product Function Max Use
Poly Plus Well Drilling Aid NA

[1] These products are designed to be flushed out prior to using the system for drinking
    water.  Before being placed into service, the well is to be properly flushed according
    to the manufacturer's use instructions.  Certification of these products is based on the
    well drilling model with the following assumptions:
    - The amount of well drilling fluid used is 3780 L (1000 U.S. gallons) to which 
      the drilling fluid has been added at 7.6 L.
    - The aquifer contains 3.1 million liters of water (815,000 gallons) based on a 0.5 acre
      aquifer of 6.1 meter depth (20 ft.) and 25% porosity.
    - The bore hole is 61 meters in total depth (200 ft.), the screen is 6.1 meters in
    length
      (20 ft.), and the bore hole is 25.4 cm.  in diameter (10 in.).
    - The amount of well drilling fluid removed from the well during construction is equal
    to
      the combined volumes of the casing and the screen, plus an additional amount removed
      through the well disinfection and development (90% removed). 
    These products should not be used in constructing wells in highly porous formations such
    as cavernous limestone.
[PC] Polyacrylamide Products Certified by NSF International comply with 40 CFR 141.111
     requirements for percent monomer and dose.


Facility : # 8 USA


Polyacrylamide [PC]
Trade Designation Product Function Max Use
Poly Plus[1] [2] [3] Well Drilling Aid NA

[1] These products should not be used in constructing wells in highly porous formations such
    as cavernous limestone.
[2] These products are designed to be flushed out prior to using the system for drinking
    water.  Before being placed in service, the well is to be properly flushed according to
    the manufacturer's use instructions.
[3] Certification of these products is based on a well drilling model with the following
    assumptions: The amount of well drilling fluid used is 3780 L (1000 U.S. gallons) to
    which the drilling fluid has been added at the manufacturer's recommended level.  The
    aquifer contains 3.1 million liters of water (815,000 gallons) based on a 0.5 acre
    aquifer of 6.1 meter depth (20 ft.) and 25% porosity.  The bore hole is 61 meters in
    total depth (200 ft.), the screen is 6.1 meters in length (20 ft.), and the bore hole is
    25.4 cm in diameter (10 in.).  The amount of well drilling fluid removed from the well
    during construction is equal to the combined volumes of the casing, the screen, and the
    bore hole annuals around the casing and the screen, plus an additional amount removed
    through the well disinfection and development (90% removed).
[PC] Polyacrylamide Products Certified by NSF International comply with 40 CFR 141.111
     requirements for percent monomer and dose.


Facility : # 11 USA


Polyacrylamide[PC]
Trade Designation Product Function Max Use
Poly-Plus Well Drilling Aid NA

[PC] Polyacrylamide Products Certified by NSF International comply with 40 CFR 141.111
     requirements for percent monomer and dose.


Facility : # 12 USA


Miscellaneous Water Supply Products [WL]
Trade Designation Product Function Max Use
Poly-Plus 2000[1] Well Drilling Aid NA

[1] Certification of these products is based on a well drilling model with the following
    assumptions:
    The amount of well drilling aid used is 3780 liters (1000 U.S. gallons) to which the
    drilling fluid has been added at the manufacturer's recommended level.  The aquifer
    contains 3.1 million liters (815,000 gallons) based on a 0.5 acre aquifer of 6.1 meter
    depth (20 ft.) and 25% porosity.  The bore hole is 61 meters in total depth (200 ft.),
    the screen is 6.1 meters in length (20 ft.), and the bore hole is 25.4 cm in diameter
    (10 in.).  The amount of well drilling fluid removed from the well during construction
    is equal to the combined volumes of the casing, the screen, and the bore hole annulus
    around the casing and the screen, plus an additional amount removed through the well
    disinfection and development (90% removed).
[WL] These products are designed to be flushed out prior to using the system for drinking

     water.  The well shall be properly flushed and drained before being placed in service.


Facility : # 16 USA


Miscellaneous Water Supply Products[1]
Trade Designation Product Function Max Use
DRILPLEX HDD Well Drilling Aid NA

[1] Certification of these products is based on the well drilling model with the following
    assumptions:
    - The amount of well drilling fluid used is 3780 L (1000 U.S. gallons) to which the
    drilling fluid has been added at the manufacturer's recommended level.
    - The aquifer contains 3.1 million liters of water (815,000 gallons) based on a 0.5 acre
    aquifer of 6.1 meter depth (20 ft.) and 25% porosity.
    - The bore hole is 61 meters in total depth (200 ft.), the screen is 6.1 meters in
    length
    (20 ft.), and the bore hole is 25.4 cm. in diameter (10 in.).
    - The amount of well drilling fluid removed from the well during construction is equal
    to
    the combined volumes of the casing and the screen, plus an additional amount removed
    through the well disinfection and development (90% removed).


Facility : # 18 USA


Miscellaneous Water Supply Products [PC]
Trade Designation Product Function Max Use
Poly-Plus 2000[1] Well Drilling Aid NA

[1] This product is designed to be used off-line following manufacturer’s use instructions.
    The well is to be flushed until the turbidity of the water is < 1 NTU before the system
    may be used for drinking water.
[PC] Polyacrylamide Products Certified by NSF International comply with 40 CFR 141.111
     requirements for percent monomer and dose.


Facility : Roundup, MT


Miscellaneous Water Supply Products[1]
Trade Designation Product Function Max Use
MAX GEL Well Drilling Aid NA

[1] The well is to be properly flushed and drained until the turbidity of the water is <1
    NTU.


Facility : Houston, TX


Miscellaneous Water Supply Products[WL]
Trade Designation Product Function Max Use
Federal Bentonite Well Drilling Aid NA
M-I Gel Well Drilling Aid NA
M-I Gel Supreme Well Drilling Aid NA
Max Gel Well Drilling Aid NA

[WL] These products are designed to be flushed out prior to using the system for drinking

     water.  The well shall be properly flushed and drained before being placed in service.


Facility : Greybull, WY


Miscellaneous Water Supply Products[WL]
Trade Designation Product Function Max Use
Aztec Hi-Yield Well Drilling Aid NA
M-I Gel Supreme Well Drilling Aid NA
Max Gel Well Drilling Aid NA

[WL] These products are designed to be flushed out prior to using the system for drinking
     water.  The well is to be properly flushed and drained before being placed in service.
     



 
M-I L.L.C. 
A Smith/Schlumberger Company
P.O. Box 42842 
Suite 407 
Houston, TX 77242 
United States 
832-295-2747

Facility : # 3 USA


Miscellaneous Water Supply Products[1] [2]
Trade Designation Product Function Max Use
Tackle Well Drilling Aid
Well Cleaning Aid
NA

[1] This product is designed to be flushed out prior to using the system for drinking water.
     The well is to be properly flushed and drained before being placed into service.  This
    product is to be used according to the manufacturer's use instructions.
[2] These products are designed to be flushed out prior to using the system for drinking
    water. Before being placed into service, the well is to be properly flushed according to
    the manufacturer's use instructions. Certification of these products is based on the
    well drilling model with the following assumptions: 
    - The amount of well drilling fluid used is 3780 L (1000 U.S. gallons) to which
      the drilling fluid has been added at the manufacturer's recommended level.
    - The aquifer contains 3.1 million liters of water (815,000 gallons) based on a 0.5 acre
      aquifer of 6.1 meter depth (20 ft.) and 25% porosity.
    - The bore hole is 61 meters in total depth (200 ft.), the screen is 6.1 meters in
    length
      (20 ft.), and the bore hole is 25.4 cm. in diameter (10 in.).
    - The amount of well drilling fluid removed from the well during construction is equal
    to 
      the combined volumes of the casing and the screen, plus an additional amount removed 
      through the well disinfection and development (90% removed).
    - This product should not be used in constructing wells in highly porous formations,
    such
      as cavernous limestone.
    

Polyacrylamide [PC]
Trade Designation Product Function Max Use
Poly-Plus 2000[1] Well Drilling Aid NA
Poly-Plus EHV[2] Well Drilling Aid NA
Poly-Plus LV[2] [PY] Well Drilling Aid NA
Poly-Plus RD[2] Well Drilling Aid NA

[1] This product is designed to be flushed out prior to using the system for drinking water.
     The well is to be properly flushed and drained before being placed into service.  This
    product is to be used according to the manufacturer's use instructions.
[2] These products are designed to be flushed out prior to using the system for drinking
    water. Before being placed into service, the well is to be properly flushed according to
    the manufacturer's use instructions. Certification of these products is based on the
    well drilling model with the following assumptions: 
    - The amount of well drilling fluid used is 3780 L (1000 U.S. gallons) to which
      the drilling fluid has been added at the manufacturer's recommended level.
    - The aquifer contains 3.1 million liters of water (815,000 gallons) based on a 0.5 acre
      aquifer of 6.1 meter depth (20 ft.) and 25% porosity.
    - The bore hole is 61 meters in total depth (200 ft.), the screen is 6.1 meters in
    length
      (20 ft.), and the bore hole is 25.4 cm. in diameter (10 in.).
    - The amount of well drilling fluid removed from the well during construction is equal
    to 
      the combined volumes of the casing and the screen, plus an additional amount removed 
      through the well disinfection and development (90% removed).
    - This product should not be used in constructing wells in highly porous formations,
    such
      as cavernous limestone.
    
[PC] Polyacrylamide Products Certified by NSF International comply with 40 CFR 141.111
     requirements for percent monomer and dose.
[PY] Polyamines Certified by NSF International comply with 40 CFR 141.111 requirements for
     percent monomer and dose.

Sodium Polyacrylate[1] [2]
Trade Designation Product Function Max Use
RINGFREE Well Cleaning Aid
Well Drilling Aid
NA

[1] This product is designed to be flushed out prior to using the system for drinking water.
     The well is to be properly flushed and drained before being placed into service.  This
    product is to be used according to the manufacturer's use instructions.
[2] These products are designed to be flushed out prior to using the system for drinking
    water. Before being placed into service, the well is to be properly flushed according to
    the manufacturer's use instructions. Certification of these products is based on the
    well drilling model with the following assumptions: 
    - The amount of well drilling fluid used is 3780 L (1000 U.S. gallons) to which
      the drilling fluid has been added at the manufacturer's recommended level.
    - The aquifer contains 3.1 million liters of water (815,000 gallons) based on a 0.5 acre
      aquifer of 6.1 meter depth (20 ft.) and 25% porosity.
    - The bore hole is 61 meters in total depth (200 ft.), the screen is 6.1 meters in
    length
      (20 ft.), and the bore hole is 25.4 cm. in diameter (10 in.).
    - The amount of well drilling fluid removed from the well during construction is equal
    to 
      the combined volumes of the casing and the screen, plus an additional amount removed 
      through the well disinfection and development (90% removed).
    - This product should not be used in constructing wells in highly porous formations,
    such
      as cavernous limestone.
    



 
M-I L.L.C. 
5950 North Course Drive
Houston, TX 77072 
United States 
403-650-2154

Facility : # 1 China


Miscellaneous Water Supply Products[WS]
Trade Designation Product Function Max Use
Platinum PAC Well Drilling Aid NA
Platinum PAC UL Well Drilling Aid NA

[WS] The well shall be properly flushed and drained before being placed in service.



 
M-I SWACO, A Schlumberger Company 
5950 North Course Drive
Houston, TX 77072 
United States 
832-295-2747

Facility : # 19 USA


Miscellaneous Water Supply Products[WL]
Trade Designation Product Function Max Use
Tackle Well Drilling Aid NA

[WL] These products are designed to be flushed out prior to using the system for drinking

     water.  The well shall be properly flushed and drained before being placed in service.



 
Millennium Water Management Ltd 
65 Coventry Lane
Dartmouth, NS B2V 2K5 
Canada 
902-462-3868

Facility : # 1 Z USA


Polyacrylamide [PC]
Trade Designation Product Function Max Use
MWML EM 533PWG[1] Well Drilling Aid NA

[1] This product is designed to be flushed out prior to using the system for drinking water.
     The well is to be properly flushed and drained before being placed into service.  This
    product is to be used according to the manufacturer's use instructions.
[PC] Polyacrylamide Products Certified by NSF International comply with 40 CFR 141.111
     requirements for percent monomer and dose.



 
Minex LLC 
115 South 14 1/2 Avenue West
Virginia, MN 55792 
United States 
800-582-7171 
218-741-7300
Visit this company's website

Facility : Virginia, MN


Polyacrylamide [PC]
Trade Designation Product Function Max Use
1330[1] Well Drilling Aid NA
Minex 1330 Well Drilling Aid NA

[1] These products are designed to be flushed out prior to using the system for drinking
    water.  Before being placed into service, the well is to be properly flushed according
    to the manufacturer's use instructions.
    Certification of these products is based on the well drilling model with the following
    assumptions:
    - The amount of well drilling fluid used is 3780 L (1000 U.S. gallons) to which the     
       drilling fluid has been added at the manufacturer's recommended level.
    - The aquifer contains 3.1 million liters of water (815,000 gallons) based on a 0.5 acre
       aquifer of 6.1 meter depth (20 ft.) and 25% porosity.
    - The bore hole is 61 meters in total depth (200 ft.), the screen is 6.1 meters in
    length   (20 ft.), and the bore hole is 25.4 cm. in diameter (10 in.).
    - The amount of well drilling fluid removed from the well during construction is equal
    to   the combined volumes of the casing and the screen, plus an additional amount
    removed      through the well disinfection and development (90% removed).
    - This product should not be used in constructing wells in highly porous formations,
    such   as cavernous limestone.
[PC] Polyacrylamide Products Certified by NSF International comply with 40 CFR 141.111
     requirements for percent monomer and dose.



 
Neo Solutions, Inc. 
1340 Brighton Road
Beaver, PA 15009 
United States 
724-728-1847
Visit this company's website

Facility : Newell, PA


Miscellaneous Water Supply Products
Trade Designation Product Function Max Use
HW 1353P[1] Well Cleaning Aid
Well Drilling Aid
NA
NS 1353P[1] Well Cleaning Aid
Well Drilling Aid
NA

[1] This product should not be used in constructing wells in highly porous formation such as
    cavernous limestone. This product is designed to be used off-line and flushed out prior
    to using the system for drinking water, following manufacturer's use instructions.
    Certification of this product is based on a well drilling model with the following
    assumptions: 
    The amount of well drilling fluid used is 3780 L (1000 U.S. gallons) to which the
    drilling fluid has been added at the manufacturer's recommended level. The aquifer
    contains 3.1 million liters of water (815,000 gallons) based on a 0.5 acre aquifer of
    6.1 meter depth (20 ft.) and 25% porosity. The bore hole is 61 meters (200 ft.) in total
    depth, the screen is 6.1 meters in length (20 ft.), and the bore hole is 25.4 cm (10
    in.) in diameter. The amount of well drilling fluid removed from the well during
    construction is equal to the combined volumes of the casing, the screen and the bore
    hole annuals around the casing and the screen, plus an additional amount removed through
    the well disinfection and development (90% removed).

Polyacrylamide [PC]
Trade Designation Product Function Max Use
NS 6353P[1] Well Drilling Aid NA
NS 6355P[1] Well Drilling Aid NA
NS 6853P[1] Well Drilling Aid NA
NS 6950P[1] Well Drilling Aid NA

[1] This product should not be used in constructing wells in highly porous formation such as
    cavernous limestone. This product is designed to be used off-line and flushed out prior
    to using the system for drinking water, following manufacturer's use instructions.
    Certification of this product is based on a well drilling model with the following
    assumptions: 
    The amount of well drilling fluid used is 3780 L (1000 U.S. gallons) to which the
    drilling fluid has been added at the manufacturer's recommended level. The aquifer
    contains 3.1 million liters of water (815,000 gallons) based on a 0.5 acre aquifer of
    6.1 meter depth (20 ft.) and 25% porosity. The bore hole is 61 meters (200 ft.) in total
    depth, the screen is 6.1 meters in length (20 ft.), and the bore hole is 25.4 cm (10
    in.) in diameter. The amount of well drilling fluid removed from the well during
    construction is equal to the combined volumes of the casing, the screen and the bore
    hole annuals around the casing and the screen, plus an additional amount removed through
    the well disinfection and development (90% removed).
[PC] Polyacrylamide Products Certified by NSF International comply with 40 CFR 141.111
     requirements for percent monomer and dose.

Sodium Polyacrylate
Trade Designation Product Function Max Use
HW 1162P[1] Well Cleaning Aid
Well Drilling Aid
NA
NS 1162P[1] Well Cleaning Aid
Well Drilling Aid
NA

[1] This product should not be used in constructing wells in highly porous formation such as
    cavernous limestone. This product is designed to be used off-line and flushed out prior
    to using the system for drinking water, following manufacturer's use instructions.
    Certification of this product is based on a well drilling model with the following
    assumptions: 
    The amount of well drilling fluid used is 3780 L (1000 U.S. gallons) to which the
    drilling fluid has been added at the manufacturer's recommended level. The aquifer
    contains 3.1 million liters of water (815,000 gallons) based on a 0.5 acre aquifer of
    6.1 meter depth (20 ft.) and 25% porosity. The bore hole is 61 meters (200 ft.) in total
    depth, the screen is 6.1 meters in length (20 ft.), and the bore hole is 25.4 cm (10
    in.) in diameter. The amount of well drilling fluid removed from the well during
    construction is equal to the combined volumes of the casing, the screen and the bore
    hole annuals around the casing and the screen, plus an additional amount removed through
    the well disinfection and development (90% removed).



 
Neo-Solutions, Inc. 
1340 Brighton Road
P.O. Box 26 
Beaver, PA 15009-0026 
United States 
724-728-1847

Facility : # 1 USA


Miscellaneous Water Supply Products
Trade Designation Product Function Max Use
NS 1353P[1] [2] Well Cleaning Aid
Well Drilling Aid
NA

[1] This product is designed to be flushed out prior to using the system for drinking water.
     The well is to be properly flushed and drained before being placed into service. This
    product is to be used according to the manufacturer's use instructions.
[2] These products are designed to be flushed out prior to using the system for drinking
    water. Before being placed into service, the well is to be properly flushed according to
    the manufacturer's use instructions. Certification of these products is based on the
    well drilling model with the following assumptions: 
    - The amount of well drilling fluid used is 3780 L (1000 U.S. gallons) to which
      the drilling fluid has been added at the manufacturer's recommended level.
    - The aquifer contains 3.1 million liters of water (815,000 gallons) based on a 0.5 acre
      aquifer of 6.1 meter depth (20 ft.) and 25% porosity.
    - The bore hole is 61 meters in total depth (200 ft.), the screen is 6.1 meters in
    length
      (20 ft.), and the bore hole is 25.4 cm. in diameter (10 in.).
    - The amount of well drilling fluid removed from the well during construction is equal
    to 
      the combined volumes of the casing and the screen, plus an additional amount removed 
      through the well disinfection and development (90% removed).
    - This product should not be used in constructing wells in highly porous formations,
    such
      as cavernous limestone.

Polyacrylamide [PC]
Trade Designation Product Function Max Use
NS 6350P[1] [2] Well Drilling Aid NA
NS 6355P[2] Well Drilling Aid NA
NS 6850P[1] [2] Well Drilling Aid NA
NS 6950P[2] Well Drilling Aid NA

[1] This product is designed to be flushed out prior to using the system for drinking water.
     The well is to be properly flushed and drained before being placed into service. This
    product is to be used according to the manufacturer's use instructions.
[2] These products are designed to be flushed out prior to using the system for drinking
    water. Before being placed into service, the well is to be properly flushed according to
    the manufacturer's use instructions. Certification of these products is based on the
    well drilling model with the following assumptions: 
    - The amount of well drilling fluid used is 3780 L (1000 U.S. gallons) to which
      the drilling fluid has been added at the manufacturer's recommended level.
    - The aquifer contains 3.1 million liters of water (815,000 gallons) based on a 0.5 acre
      aquifer of 6.1 meter depth (20 ft.) and 25% porosity.
    - The bore hole is 61 meters in total depth (200 ft.), the screen is 6.1 meters in
    length
      (20 ft.), and the bore hole is 25.4 cm. in diameter (10 in.).
    - The amount of well drilling fluid removed from the well during construction is equal
    to 
      the combined volumes of the casing and the screen, plus an additional amount removed 
      through the well disinfection and development (90% removed).
    - This product should not be used in constructing wells in highly porous formations,
    such
      as cavernous limestone.
[PC] Polyacrylamide Products Certified by NSF International comply with 40 CFR 141.111
     requirements for percent monomer and dose.

Sodium Polyacrylate
Trade Designation Product Function Max Use
NS 1162P[1] [2] Well Cleaning Aid
Well Drilling Aid
NA

[1] This product is designed to be flushed out prior to using the system for drinking water.
     The well is to be properly flushed and drained before being placed into service. This
    product is to be used according to the manufacturer's use instructions.
[2] These products are designed to be flushed out prior to using the system for drinking
    water. Before being placed into service, the well is to be properly flushed according to
    the manufacturer's use instructions. Certification of these products is based on the
    well drilling model with the following assumptions: 
    - The amount of well drilling fluid used is 3780 L (1000 U.S. gallons) to which
      the drilling fluid has been added at the manufacturer's recommended level.
    - The aquifer contains 3.1 million liters of water (815,000 gallons) based on a 0.5 acre
      aquifer of 6.1 meter depth (20 ft.) and 25% porosity.
    - The bore hole is 61 meters in total depth (200 ft.), the screen is 6.1 meters in
    length
      (20 ft.), and the bore hole is 25.4 cm. in diameter (10 in.).
    - The amount of well drilling fluid removed from the well during construction is equal
    to 
      the combined volumes of the casing and the screen, plus an additional amount removed 
      through the well disinfection and development (90% removed).
    - This product should not be used in constructing wells in highly porous formations,
    such
      as cavernous limestone.



 
Newpark Drilling Fluids LLC 
21920 Merchants Way
Katy, TX 77449 
United States 
800-444-0682 
281-754-8600

Facility : # 1 USA


Polyacrylamide [PC]
Trade Designation Product Function Max Use
DrilEase 242[1] Well Drilling Aid NA
NewPHPA[1] [2] Well Drilling Aid NA

[1] These products are designed to be flushed out prior to using the system for drinking
    water. Before being placed into service, the well is to be properly flushed according to
    the manufacturer's use instructions. Certification of these products is based on the
    well drilling model with the following assumptions: 
    - The amount of well drilling fluid used is 3780 L (1000 U.S. gallons) to which
      the drilling fluid has been added at the manufacturer's recommended level.
    - The aquifer contains 3.1 million liters of water (815,000 gallons) based on a 0.5 
      acre aquifer of 6.1 meter depth (20 ft.) and 25% porosity.
    - The bore hole is 61 meters in total depth (200 ft.), the screen is 6.1 meters in 
      length (20 ft.), and the bore hole is 25.4 cm. in diameter (10 in.).
    - The amount of well drilling fluid removed from the well during construction is equal
      to the combined volumes of the casing and the screen, plus an additional amount
      removed through the well disinfection and development (90% removed).
    - This product should not be used in constructing wells in highly porous formations, 
      such as cavernous limestone.
[2] This product is designed to be flushed out prior to using the system for drinking water.
     The well is to be properly flushed and drained before being placed into service.  This
    product is to be used according to the manufacturer's use instructions.
[PC] Polyacrylamide Products Certified by NSF International comply with 40 CFR 141.111
     requirements for percent monomer and dose.



 
Northstar Chemical Inc. 
14200 Southwest Tualatin Sherwood Road
Sherwood, OR 97140 
United States 
800-873-4869

Facility : # 1 USA


Polyacrylamide[PC]
Trade Designation Product Function Max Use
EA-649 PWG Well Drilling Aid 1mg/L
MEA-649 PWG Well Drilling Aid 1mg/L

[PC] Polyacrylamide Products Certified by NSF International comply with 40 CFR 141.111
     requirements for percent monomer and dose.

[1] This product is designed to be flushed out prior to using the system for drinking water.
     The well is to be properly flushed and drained before being placed into service.  This
    product is to be used according to the manufacturer's use instructions.
[2] These products are designed to be flushed out prior to using the system for drinking
    water. Before being placed into service, the well is to be properly flushed according to
    the manufacturer's use instructions. Certification of these products is based on the
    well drilling model with the following assumptions: 
    - The amount of well drilling fluid used is 3780 L (1000 U.S. gallons) to which
      the drilling fluid has been added at the manufacturer's recommended level.
    - The aquifer contains 3.1 million liters of water (815,000 gallons) based on a 0.5 acre
      aquifer of 6.1 meter depth (20 ft.) and 25% porosity.
    - The bore hole is 61 meters in total depth (200 ft.), the screen is 6.1 meters in
    length
      (20 ft.), and the bore hole is 25.4 cm. in diameter (10 in.).
    - The amount of well drilling fluid removed from the well during construction is equal
    to 
      the combined volumes of the casing and the screen, plus an additional amount removed 
      through the well disinfection and development (90% removed).
    - This product should not be used in constructing wells in highly porous formations,
    such
      as cavernous limestone.


 
NorthStar Fluid Solutions 
P.O. Box 3395
Englewood, CO 80155 
United States 
303-495-3130

Facility : # 1 USA


Bentonite
Trade Designation Product Function Max Use
Star Gel Xtra Drilling Fluid
Well Drilling Aid
NA



 
Northstar Fluid Solutions 
P.O. Box 271036
Louisville, CO 80027 
United States 
303-495-3130

Facility : # 3 USA


Polyacrylamide [PC]
Trade Designation Product Function Max Use
Star Drill Dry[1] Well Drilling Aid NA

[1] These products are designed to be flushed out prior to using the system for
    drinkingwater. Before being placed into service, the well is to be properly flushed
    according
    to the manufacturer's use instructions. Certification of these products is based on
    the well drilling model with the following assumptions:
    - The amount of well drilling fluid used is 3780 L (1000 U.S. gallons) to which the
    drilling fluid has been added at the manufacturer's recommended level.
    - The aquifer contains 3.1 million liters of water (815,000 gallons) based on a 0.5
    acre aquifer of 6.1 meter depth (20 ft.) and 25% porosity.
    - The bore hole is 61 meters in total depth (200 ft.), the screen is 6.1 meters in
    length (20 ft.), and the bore hole is 25.4 cm in diameter (10 in.).
    - The amount of well drilling fluid removed from the well during construction is equal
    to the combined volumes of the casing and the screen, plus an additional amount
    removed through the well disinfection and development (90% removed).
    - This product should not be used in constructing wells in highly porous formations,
    such as cavernous limestone.
[PC] Polyacrylamide Products Certified by NSF International comply with 40 CFR 141.111
     requirements for percent monomer and dose.



 
NorthStar Fluid Solutions LLC 
P.O. Box 271036
Louisville, CO 80027 
United States 
303-495-3130

Facility : # 4 USA


Miscellaneous Water Supply Products[1]
Trade Designation Product Function Max Use
Star-Drill 2000 Well Drilling Aid NA

[1] These products are designed to be flushed out prior to using the system for drinking
    water. Before being placed into service, the well is to be properly flushed according to
    the manufacturer's use instructions. Certification of these products is based on the
    well drilling model with the following assumptions:
      - The amount of well drilling fluid used is 3780 L (1000 U.S. gallons) to which the
        drilling fluid has been added at the manufacturer's recommended level.
      - The aquifer contains 3.1 million liters of water (815,000 gallons) based on a 0.5 
        acre aquifer of 6.1 meter depth (20 ft.) and 25% porosity.
      - The bore hole is 61 meters in total depth (200 ft.), the screen is 6.1 meters 
        in length (20 ft.), and the bore hole is 25.4 cm. in diameter (10 in.).
      - The amount of well drilling fluid removed from the well during construction 
        is equal to the combined volumes of the casing and the screen, plus an additional 
        amount removed through the well disinfection and development (90% removed).
      - This product should not be used in constructing wells in highly porous formations, 
        such as cavernous limestone.



 
Seatex, Ltd. 
445 Texas 36
P.O. Box D 
Rosenberg, TX 77471 
United States 
800-829-3020 
713-357-5300
Visit this company's website

Facility : Rosenberg, TX


Polyacrylamide[3] [PC]
Trade Designation Product Function Max Use
C-Drill Well Drilling Aid NA
IDP-567B Well Drilling Aid NA

[3] These products are designed to be flushed out prior to using the system for drinking
    water. Before being placed into service, the well is to be properly flushed according to
    the manufacturer's use instructions. Certification of these products is based on the
    well drilling model with the following assumptions:
         - The amount of well drilling fluid used is 3780 L (1000 U.S. gallons) to which the
           drilling fluid has been added at the manufacturer's recommended level.
         - The aquifer contains 3.1 million liters of water (815,000 gallons) based on a 0.5
           acre aquifer of 6.1 meter depth (20 ft.) and 25% porosity.
         - The bore hole is 61 meters in total depth (200 ft.), the screen is 6.1 meters in
           length (20 ft.), and the bore hole is 25.4 cm. in diameter (10 in.).
         - The amount of well drilling fluid removed from the well during construction is
           equal to the combined volumes of the casing and the screen, plus an additional
           amount removed through the well disinfection and development (90% removed).
         - This product should not be used in constructing wells in highly porous
    formations,
           such as cavernous limestone.
[PC] Polyacrylamide Products Certified by NSF International comply with 40 CFR 141.111
     requirements for percent monomer and dose.



 
SNF Inc. 
1 Chemical Plant Road
P.O. Box 250 
Riceboro, GA 31323 
United States 
912-884-3366
Visit this company's website

Facility : Riceboro, GA


Miscellaneous Water Supply Products
Trade Designation Product Function Max Use
Flosperse 3018 CS PWG[1] [2] Well Drilling Aid
Well Cleaning Aid
NA

[1] This product is designed to be flushed out prior to using the system for drinking water.
     The well is to be properly flushed and drained before being placed into service.  This
    product is to be used according to the manufacturer's use instructions.
[2] These products are designed to be flushed out prior to using the system for drinking
    water. Before being placed into service, the well is to be properly flushed according to
    the manufacturer's use instructions. Certification of these products is based on the
    well drilling model with the following assumptions: 
    - The amount of well drilling fluid used is 3780 L (1000 U.S. gallons) to which
      the drilling fluid has been added at the manufacturer's recommended level.
    - The aquifer contains 3.1 million liters of water (815,000 gallons) based on a 0.5 acre
      aquifer of 6.1 meter depth (20 ft.) and 25% porosity.
    - The bore hole is 61 meters in total depth (200 ft.), the screen is 6.1 meters in
    length
      (20 ft.), and the bore hole is 25.4 cm. in diameter (10 in.).
    - The amount of well drilling fluid removed from the well during construction is equal
    to 
      the combined volumes of the casing and the screen, plus an additional amount removed 
      through the well disinfection and development (90% removed).
    - This product should not be used in constructing wells in highly porous formations,
    such
      as cavernous limestone.

Polyacrylamide [PC]
Trade Designation Product Function Max Use
Clarifloc® A-3333P[1] [2] Well Drilling Aid NA
Clarifloc® A-3340[2] Well Drilling Aid NA
Clarifloc® A-3345[2] Well Drilling Aid NA
Clarifloc® A-3360[2] Well Drilling Aid NA
FLOPAM™ AN 934 BPM PWG[1] [2] Well Drilling Aid NA
FLOPAM™ AN 934 PWG[1] [2] Well Drilling Aid NA
FLOPAM™ AN 934 XD PWG Well Drilling Aid NA
FLOPAM™ AN 945 PWG[2] Well Drilling Aid NA
FLOPAM™ AN 945 VHM PWG[2] Well Drilling Aid NA
FLOPAM™ AN 945 XD PWG[1] [2] Well Drilling Aid NA
FLOPAM™ AN 956 PWG[2] Well Drilling Aid NA
FLOPAM™ DW 533 PWG BCK[2] Well Drilling Aid NA
FLOPAM™ EM 533 A25 PWG Well Drilling Aid NA
FLOPAM™ EMF 533 B26 PWG Well Drilling Aid NA
FLOPAM™ EMF 533 B30 PWG[1] [2] Well Drilling Aid NA
FLOPAM™ EMF 533 PWG[1] [2] Well Drilling Aid NA
Flopam™ DW 533 B PWG[2] Well Drilling Aid NA
Flopam™ EMF 532 PWG[1] [2] Well Drilling Aid NA

[1] This product is designed to be flushed out prior to using the system for drinking water.
     The well is to be properly flushed and drained before being placed into service.  This
    product is to be used according to the manufacturer's use instructions.
[2] These products are designed to be flushed out prior to using the system for drinking
    water. Before being placed into service, the well is to be properly flushed according to
    the manufacturer's use instructions. Certification of these products is based on the
    well drilling model with the following assumptions: 
    - The amount of well drilling fluid used is 3780 L (1000 U.S. gallons) to which
      the drilling fluid has been added at the manufacturer's recommended level.
    - The aquifer contains 3.1 million liters of water (815,000 gallons) based on a 0.5 acre
      aquifer of 6.1 meter depth (20 ft.) and 25% porosity.
    - The bore hole is 61 meters in total depth (200 ft.), the screen is 6.1 meters in
    length
      (20 ft.), and the bore hole is 25.4 cm. in diameter (10 in.).
    - The amount of well drilling fluid removed from the well during construction is equal
    to 
      the combined volumes of the casing and the screen, plus an additional amount removed 
      through the well disinfection and development (90% removed).
    - This product should not be used in constructing wells in highly porous formations,
    such
      as cavernous limestone.
[PC] Polyacrylamide Products Certified by NSF International comply with 40 CFR 141.111
     requirements for percent monomer and dose.

Polyamines [PY]
Trade Designation Product Function Max Use
FLOQUAT™ FL 2449 PWG[2] Well Drilling Aid NA

[2] These products are designed to be flushed out prior to using the system for drinking
    water. Before being placed into service, the well is to be properly flushed according to
    the manufacturer's use instructions. Certification of these products is based on the
    well drilling model with the following assumptions: 
    - The amount of well drilling fluid used is 3780 L (1000 U.S. gallons) to which
      the drilling fluid has been added at the manufacturer's recommended level.
    - The aquifer contains 3.1 million liters of water (815,000 gallons) based on a 0.5 acre
      aquifer of 6.1 meter depth (20 ft.) and 25% porosity.
    - The bore hole is 61 meters in total depth (200 ft.), the screen is 6.1 meters in
    length
      (20 ft.), and the bore hole is 25.4 cm. in diameter (10 in.).
    - The amount of well drilling fluid removed from the well during construction is equal
    to 
      the combined volumes of the casing and the screen, plus an additional amount removed 
      through the well disinfection and development (90% removed).
    - This product should not be used in constructing wells in highly porous formations,
    such
      as cavernous limestone.
[PY] Polyamines Certified by NSF International comply with 40 CFR 141.111 requirements for
     percent monomer and dose.

Sodium Polyacrylate[1] [2]
Trade Designation Product Function Max Use
Flosperse 3000 PWG Well Cleaning Aid
Well Drilling Aid
NA

[1] This product is designed to be flushed out prior to using the system for drinking water.
     The well is to be properly flushed and drained before being placed into service.  This
    product is to be used according to the manufacturer's use instructions.
[2] These products are designed to be flushed out prior to using the system for drinking
    water. Before being placed into service, the well is to be properly flushed according to
    the manufacturer's use instructions. Certification of these products is based on the
    well drilling model with the following assumptions: 
    - The amount of well drilling fluid used is 3780 L (1000 U.S. gallons) to which
      the drilling fluid has been added at the manufacturer's recommended level.
    - The aquifer contains 3.1 million liters of water (815,000 gallons) based on a 0.5 acre
      aquifer of 6.1 meter depth (20 ft.) and 25% porosity.
    - The bore hole is 61 meters in total depth (200 ft.), the screen is 6.1 meters in
    length
      (20 ft.), and the bore hole is 25.4 cm. in diameter (10 in.).
    - The amount of well drilling fluid removed from the well during construction is equal
    to 
      the combined volumes of the casing and the screen, plus an additional amount removed 
      through the well disinfection and development (90% removed).
    - This product should not be used in constructing wells in highly porous formations,
    such
      as cavernous limestone.

NOTE: Only products bearing the NSF Mark are considered NSF Certified.

Facility : Pearlington, MS


Polyamines [PY]
Trade Designation Product Function Max Use
FLOQUAT™ FL 2449 PWG[1] Well Drilling Aid NA

[1] These products are designed to be flushed out prior to using the system for drinking
    water. Before being placed into service, the well is to be properly flushed according to
    the manufacturer's use instructions. Certification of these products is based on the
    well drilling model with the following assumptions: 
    - The amount of well drilling fluid used is 3780 L (1000 U.S. gallons) to which
      the drilling fluid has been added at the manufacturer's recommended level.
    - The aquifer contains 3.1 million liters of water (815,000 gallons) based on a 0.5 acre
      aquifer of 6.1 meter depth (20 ft.) and 25% porosity.
    - The bore hole is 61 meters in total depth (200 ft.), the screen is 6.1 meters in
    length
      (20 ft.), and the bore hole is 25.4 cm. in diameter (10 in.).
    - The amount of well drilling fluid removed from the well during construction is equal
    to 
      the combined volumes of the casing and the screen, plus an additional amount removed 
      through the well disinfection and development (90% removed).
    - This product should not be used in constructing wells in highly porous formations,
    such
      as cavernous limestone.
[PY] Polyamines Certified by NSF International comply with 40 CFR 141.111 requirements for
     percent monomer and dose.

NOTE: Only products bearing the NSF Mark are considered NSF Certified.


 
SNF SAS 
ZAC de Milieux
42163 Andrezieux 
France 
33 47 736 8600
Visit this company's website

Facility : Andrézieux, France


Miscellaneous Water Supply Products
Trade Designation Product Function Max Use
Flosperse 3018 CS PWG[1] Well Drilling Aid
Well Cleaning Aid
NA

[1] These products are designed to be flushed out prior to using the system for drinking
    water. Before being placed into service, the well is to be properly flushed according to
    the manufacturer's use instructions. Certification of these products is based on the
    well drilling model with the following assumptions: 
    - The amount of well drilling fluid used is 3780 L (1000 U.S. gallons) to which
      the drilling fluid has been added at the manufacturer's recommended level.
    - The aquifer contains 3.1 million liters of water (815,000 gallons) based on a 0.5 acre
      aquifer of 6.1 meter depth (20 ft.) and 25% porosity.
    - The bore hole is 61 meters in total depth (200 ft.), the screen is 6.1 meters in
    length
      (20 ft.), and the bore hole is 25.4 cm. in diameter (10 in.).
    - The amount of well drilling fluid removed from the well during construction is equal
    to 
      the combined volumes of the casing and the screen, plus an additional amount removed 
      through the well disinfection and development (90% removed).
    - This product should not be used in constructing wells in highly porous formations,
    such
      as cavernous limestone.

Sodium Polyacrylate
Trade Designation Product Function Max Use
Flosperse 3000 PWG[1] Well Cleaning Aid
Well Drilling Aid
NA

[1] These products are designed to be flushed out prior to using the system for drinking
    water. Before being placed into service, the well is to be properly flushed according to
    the manufacturer's use instructions. Certification of these products is based on the
    well drilling model with the following assumptions: 
    - The amount of well drilling fluid used is 3780 L (1000 U.S. gallons) to which
      the drilling fluid has been added at the manufacturer's recommended level.
    - The aquifer contains 3.1 million liters of water (815,000 gallons) based on a 0.5 acre
      aquifer of 6.1 meter depth (20 ft.) and 25% porosity.
    - The bore hole is 61 meters in total depth (200 ft.), the screen is 6.1 meters in
    length
      (20 ft.), and the bore hole is 25.4 cm. in diameter (10 in.).
    - The amount of well drilling fluid removed from the well during construction is equal
    to 
      the combined volumes of the casing and the screen, plus an additional amount removed 
      through the well disinfection and development (90% removed).
    - This product should not be used in constructing wells in highly porous formations,
    such
      as cavernous limestone.



 
SNF SAS 
ZAC de Milieux
42163 Andrezieux 
France 
33 477 36 86 00

Facility : Riceboro, GA


Polyacrylamide [PC]
Trade Designation Product Function Max Use
FLOPAM™ AN 934 BPM PWG[1] [2] Well Drilling Aid NA
FLOPAM™ AN 934 PWG[1] [2] Well Drilling Aid NA
FLOPAM™ DW 533 PWG[2] Well Drilling Aid NA
FLOPAM™ EM 533 B30 PWG[1] [2] Well Drilling Aid NA
FLOPAM™ EM 533 PWG[1] [2] Well Drilling Aid NA
FLOPAM™ EMF 533 PWG[1] [2] Well Drilling Aid NA

[1] This product is designed to be flushed out prior to using the system for drinking water.
     The well is to be properly flushed and drained before being placed into service.  This
    product is to be used according to the manufacturer's use instructions.
[2] These products are designed to be flushed out prior to using the system for drinking
    water. Before being placed into service, the well is to be properly flushed according to
    the manufacturer's use instructions. Certification of these products is based on the
    well drilling model with the following assumptions: 
    - The amount of well drilling fluid used is 3780 L (1000 U.S. gallons) to which
      the drilling fluid has been added at the manufacturer's recommended level.
    - The aquifer contains 3.1 million liters of water (815,000 gallons) based on a 0.5 acre
      aquifer of 6.1 meter depth (20 ft.) and 25% porosity.
    - The bore hole is 61 meters in total depth (200 ft.), the screen is 6.1 meters in
    length
      (20 ft.), and the bore hole is 25.4 cm. in diameter (10 in.).
    - The amount of well drilling fluid removed from the well during construction is equal
    to 
      the combined volumes of the casing and the screen, plus an additional amount removed 
      through the well disinfection and development (90% removed).
    - This product should not be used in constructing wells in highly porous formations,
    such
      as cavernous limestone.
[PC] Polyacrylamide Products Certified by NSF International comply with 40 CFR 141.111
     requirements for percent monomer and dose.

Sodium Polyacrylate[1] [2]
Trade Designation Product Function Max Use
Flosperse 3000 PWG Well Cleaning Aid
Well Drilling Aid
NA

[1] This product is designed to be flushed out prior to using the system for drinking water.
     The well is to be properly flushed and drained before being placed into service.  This
    product is to be used according to the manufacturer's use instructions.
[2] These products are designed to be flushed out prior to using the system for drinking
    water. Before being placed into service, the well is to be properly flushed according to
    the manufacturer's use instructions. Certification of these products is based on the
    well drilling model with the following assumptions: 
    - The amount of well drilling fluid used is 3780 L (1000 U.S. gallons) to which
      the drilling fluid has been added at the manufacturer's recommended level.
    - The aquifer contains 3.1 million liters of water (815,000 gallons) based on a 0.5 acre
      aquifer of 6.1 meter depth (20 ft.) and 25% porosity.
    - The bore hole is 61 meters in total depth (200 ft.), the screen is 6.1 meters in
    length
      (20 ft.), and the bore hole is 25.4 cm. in diameter (10 in.).
    - The amount of well drilling fluid removed from the well during construction is equal
    to 
      the combined volumes of the casing and the screen, plus an additional amount removed 
      through the well disinfection and development (90% removed).
    - This product should not be used in constructing wells in highly porous formations,
    such
      as cavernous limestone.



 
Unitech Chemicals (Zibo) Limited 
Yongliu West Road, Linzi
Zibo City, Shandong Province 255400 
China 
86 533 721 7335
Visit this company's website

Facility : Shandong Province, China


Miscellaneous Water Supply Products[WS]
Trade Designation Product Function Max Use
Dynapac DHV Well Drilling Aid NA
Dynapac DHV Plus Well Drilling Aid NA
Dynapac DLV Well Drilling Aid NA
Dynapac DLV Plus Well Drilling Aid NA

[WS] The well shall be properly flushed and drained before being placed in service.



 
Western Clay Company 
620 East SR 24
Aurora, UT 84620 
United States 
800-982-7960 
435-529-3281

Facility : Aurora, UT


Bentonite
Trade Designation Product Function Max Use
Prime-Gel Drilling Fluid
Well Drilling Aid
NA
Prime-Gel Premium Drilling Fluid
Well Drilling Aid
NA
SLIKGEL High Yield Drilling Fluid
Well Drilling Aid
NA



 
Western Hydro Corporation 
3449 Enterprise Avenue
Hayward, CA 94545 
United States 
510-783-9166

Facility : # 1 USA


Bentonite
Trade Designation Product Function Max Use
Drill Mud 220[1] Well Drilling Aid NA
Hydro Bore 240[1] Well Drilling Aid NA

[1] Prior to using the system for drinking water, the well is to be properly flushed until
    the turbidity of the water is <1 NTU.

Miscellaneous Water Supply Products [WS]
Trade Designation Product Function Max Use
Hydro Polymer[2] [3] [PC] Well Drilling Aid NA

[1] Prior to using the system for drinking water, the well is to be properly flushed until
    the turbidity of the water is <1 NTU.
[2] These products should not be used in constructing wells in highly porous formations such
    as cavernous limestone.
[3] Certification of these products is based on a well drilling model with the following
    assumptions:
    -The amount of well drilling fluid used is 3780 L (1000 U.S. gallons) to which the 
     drilling fluid has been added at the manufacturer's recommended level.  
    -The aquifer contains 3.1 million liters of water (815,000 gallons) based on a 0.5 acre 
     aquifer of 6.1 meter depth (20 ft.) and 25% porosity.  
    -The bore hole is 61 meters in total depth (200 ft.), the screen is 6.1 meters in length
    
     (20 ft.), and the bore hole is 25.4 cm in diameter (10 in.).  
    -The amount of well drilling fluid removed from the well during construction is equal to
    
     the combined volumes of the casing, the screen, and bore hole annuals around the bore 
     hole annuals around the casing and the screen, plus an additional amount removed 
     through the well disinfection and development (90% removed).
[4] Certification of this product is based on a well drilling model using assumptions stated
    in NSF/ANSI Standard 60, Section 8 for well drilling foamers.
[PC] Polyacrylamide Products Certified by NSF International comply with 40 CFR 141.111
     requirements for percent monomer and dose.
[WS] The well shall be properly flushed and drained before being placed in service.

Miscellaneous Water Supply Products
Trade Designation Product Function Max Use
Hydro Thin[1] Well Drilling Aid NA

[1] Prior to using the system for drinking water, the well is to be properly flushed until
    the turbidity of the water is <1 NTU.



 
Wyo-Ben, Inc. 
1345 Discovery Drive
Billings, MT 59102 
United States 
406-652-6351
Visit this company's website

Facility : # 1 USA


Miscellaneous Water Supply Products[WL]
Trade Designation Product Function Max Use
THINZ-IT Well Drilling Aid NA

[WL] These products are designed to be flushed out prior to using the system for drinking

     water.  The well shall be properly flushed and drained before being placed in service.


Facility : # 2 USA


Miscellaneous Water Supply Products [PC]
Trade Designation Product Function Max Use
WYO-VIS[1] Well Drilling Aid NA

[1] These products should not be used in constructing wells in highly porous formations such
    as cavernous limestone.
    These products are designed to be flushed out prior to using the system for drinking
    water. Before being placed in service, the well is to be properly flushed according to
    the manufacturer's use instructions.
    Certification of these products is based on a well drilling model with the following
    assumptions:
    The amount of well drilling fluid used is 3780 L (1000 U.S. gallons) to which the
    drilling fluid has been added at the manufacturer's recommended level. The aquifer
    contains 3.1 million liters of water (815,000 gallons) based on a 0.5 acre aquifer of
    6.1 meter depth (20 ft.) and 25% porosity. The bore hole is 61 meters in total depth
    (200 ft.), the screen is 6.1 meters in length (20 ft.), and the bore hole is 25.4 cm in
    diameter (10 in.). The amount of well drilling fluid removed from the well during
    construction is equal to the combined volumes of the casing, the screen, and the bore
    hole annuals around the casing and the screen, plus an additional amount removed through
    the well disinfection and development (90% removed).
[PC] Polyacrylamide Products Certified by NSF International comply with 40 CFR 141.111
     requirements for percent monomer and dose.


Facility : # 5 USA


Miscellaneous Water Supply Products [PC]
Trade Designation Product Function Max Use
THINZ-IT[1] Well Drilling Aid NA

[1] This product is designed to be used off-line following manufacturer’s use instructions.
    The well is to be flushed until the turbidity of the water is < 1 NTU before the system
    may be used for drinking water.
[PC] Polyacrylamide Products Certified by NSF International comply with 40 CFR 141.111
     requirements for percent monomer and dose.



 
Wyo-Ben, Inc. 
1345 Discovery Drive
Billings, MT 59102 
United States 
800-548-7055 
406-652-6351
Visit this company's website

Facility : Houston, TX


Bentonite
Trade Designation Product Function Max Use
Hydrogel®[1] Well Drilling Aid NA
Naturalgel®[2] Well Drilling Aid NA

[1] These products are designed to be flushed out prior to using the system for drinking
    water.  The well is to be properly flushed and drained until the turbidity of the water
    is < 1 NTU.
[2] These products are designed to be flushed out prior to using the system for drinking
    water.  The well is to be properly flushed and drained before being placed in service.


Facility : Greybull, WY


Bentonite
Trade Designation Product Function Max Use
Cementgel™[1] Well Drilling Aid NA
Extra High Yield Bentonite[1] Well Drilling Aid NA
Hydrogel®[1] Well Drilling Aid NA
Micro-Gel™[1] Well Drilling Aid NA
Naturalgel®[WS] Well Drilling Aid NA
SW101[1] Well Drilling Aid NA
Tru-Bore®[1] Well Drilling Aid NA

[1] Prior to using the system for drinking water, the well is to be properly flushed until
    the turbidity of the water is <1 NTU.
[WS] The well shall be properly flushed and drained before being placed in service.

Miscellaneous Water Supply Products
Trade Designation Product Function Max Use
Dril-Trol™ LV[1] [3] Well Drilling Aid NA
Dril-Trol™ QD[1] [3] Well Drilling Aid NA
MTA-1™[1] Well Drilling Aid NA
THINZ-IT[1] Well Drilling Aid NA
VC-55™[4] [5] [PC] [WS] Well Drilling Aid NA

[1] Prior to using the system for drinking water, the well is to be properly flushed until
    the turbidity of the water is <1 NTU.
[2] Certification of this product is based on a well drilling model using assumptions stated
    in NSF/ANSI Standard 60, Section 8 for well drilling foamers.
[3] This product is designed to be used off-line and flushed out prior to using the system
    for drinking water, following the manufacturer's use instructions.
[4] These products should not be used in constructing wells in highly porous formations such
    as cavernous limestone.
[5] Certification of these products is based on a well drilling model with the following
    assumptions:
    -The amount of well drilling fluid used is 3780 L (1000 U.S. gallons) to which the 
     drilling fluid has been added at the manufacturer's recommended level.  
    -The aquifer contains 3.1 million liters of water (815,000 gallons) based on a 0.5 acre 
     aquifer of 6.1 meter depth (20 ft.) and 25% porosity.  
    -The bore hole is 61 meters in total depth (200 ft.), the screen is 6.1 meters in length
    
     (20 ft.), and the bore hole is 25.4 cm in diameter (10 in.).  
    -The amount of well drilling fluid removed from the well during construction is equal to
    
     the combined volumes of the casing, the screen, and bore hole annuals around the bore 
     hole annuals around the casing and the screen, plus an additional amount removed 
     through the well disinfection and development (90% removed).
[PC] Polyacrylamide Products Certified by NSF International comply with 40 CFR 141.111
     requirements for percent monomer and dose.
[WS] The well shall be properly flushed and drained before being placed in service.

Polyacrylamide [PC]
Trade Designation Product Function Max Use
KWIK-VIS™ "D"[4] [5] [6] Well Drilling Aid NA
WYO-VIS[4] [5] [6] Well Drilling Aid NA
WYO-VIS HP[4] [5] [6] Well Drilling Aid NA
WYO-VIS LVP[4] [5] [6] Well Drilling Aid NA

[4] These products should not be used in constructing wells in highly porous formations such
    as cavernous limestone.
[5] Certification of these products is based on a well drilling model with the following
    assumptions:
    -The amount of well drilling fluid used is 3780 L (1000 U.S. gallons) to which the 
     drilling fluid has been added at the manufacturer's recommended level.  
    -The aquifer contains 3.1 million liters of water (815,000 gallons) based on a 0.5 acre 
     aquifer of 6.1 meter depth (20 ft.) and 25% porosity.  
    -The bore hole is 61 meters in total depth (200 ft.), the screen is 6.1 meters in length
    
     (20 ft.), and the bore hole is 25.4 cm in diameter (10 in.).  
    -The amount of well drilling fluid removed from the well during construction is equal to
    
     the combined volumes of the casing, the screen, and bore hole annuals around the bore 
     hole annuals around the casing and the screen, plus an additional amount removed 
     through the well disinfection and development (90% removed).
[6] These products are designed to be flushed out prior to using the system for drinking
    water. Before being placed into service, the well is to be properly flushed according to
    the manufacturer's use instructions.
[PC] Polyacrylamide Products Certified by NSF International comply with 40 CFR 141.111
     requirements for percent monomer and dose.



 
Wyo-Ben, Inc. 
P.O. Box 1979
Billings, MT 59102 
United States 
406-652-6351

Facility : # 6 USA


Sodium Polyacrylate
Trade Designation Product Function Max Use
THINZ-IT[1] [2] Well Drilling Aid
Well Cleaning Aid
NA

[1] This product is designed to be flushed out prior to using the system for drinking water.
     The well is to be properly flushed and drained before being placed into service.  This
    product is to be used according to the manufacturer's use instructions.
[2] These products are designed to be flushed out prior to using the system for drinking
    water. Before being placed into service, the well is to be properly flushed according to
    the manufacturer's use instructions. Certification of these products is based on the
    well drilling model with the following assumptions: 
    - The amount of well drilling fluid used is 3780 L (1000 U.S. gallons) to which
      the drilling fluid has been added at the manufacturer's recommended level.
    - The aquifer contains 3.1 million liters of water (815,000 gallons) based on a 0.5 acre
      aquifer of 6.1 meter depth (20 ft.) and 25% porosity.
    - The bore hole is 61 meters in total depth (200 ft.), the screen is 6.1 meters in
    length
      (20 ft.), and the bore hole is 25.4 cm. in diameter (10 in.).
    - The amount of well drilling fluid removed from the well during construction is equal
    to 
      the combined volumes of the casing and the screen, plus an additional amount removed 
      through the well disinfection and development (90% removed).
    - This product should not be used in constructing wells in highly porous formations,
    such
      as cavernous limestone.

Polyacrylamide [PC]
Trade Designation Product Function Max Use
WYO-VIS® HP[1] [2] Well Drilling Aid NA

[1] This product is designed to be flushed out prior to using the system for drinking water.
     The well is to be properly flushed and drained before being placed into service.  This
    product is to be used according to the manufacturer's use instructions.
[2] These products are designed to be flushed out prior to using the system for drinking
    water. Before being placed into service, the well is to be properly flushed according to
    the manufacturer's use instructions. Certification of these products is based on the
    well drilling model with the following assumptions: 
    - The amount of well drilling fluid used is 3780 L (1000 U.S. gallons) to which
      the drilling fluid has been added at the manufacturer's recommended level.
    - The aquifer contains 3.1 million liters of water (815,000 gallons) based on a 0.5 acre
      aquifer of 6.1 meter depth (20 ft.) and 25% porosity.
    - The bore hole is 61 meters in total depth (200 ft.), the screen is 6.1 meters in
    length
      (20 ft.), and the bore hole is 25.4 cm. in diameter (10 in.).
    - The amount of well drilling fluid removed from the well during construction is equal
    to 
      the combined volumes of the casing and the screen, plus an additional amount removed 
      through the well disinfection and development (90% removed).
    - This product should not be used in constructing wells in highly porous formations,
    such
      as cavernous limestone.
[PC] Polyacrylamide Products Certified by NSF International comply with 40 CFR 141.111
     requirements for percent monomer and dose.


Number of matching Manufacturers is 54
Number of matching Products is 342
Processing time was 1 seconds