NSF Product and Service Listings
These NSF Official Listings are current as of Sunday, October 6, 2024 at 12:15 a.m. Eastern Time. Please contact NSF to confirm the status of any Listing, report errors, or make suggestions.
Alert: NSF is concerned about fraudulent downloading and manipulation of website text. Always confirm this information by clicking on the below link for the most accurate information: http://info.nsf.org/Certified/PwsComponents/Listings.asp?Company=02460&
NSF/ANSI/CAN 61
Drinking Water System Components - Health Effects
Drinking Water System Components - Health Effects
NOTE: Unless otherwise indicated for Materials, Certification is only for the Water Contact Material shown in the Listing. Click here for a list of Abbreviations used in these Listings. Click here for the definitions of Water Contact Temperatures denoted in these Listings. Products certified to NSF/ANSI/CAN 61 comply with the health effects criteria in NSF/ANSI/CAN 600.
PPG Protective and Marine Coatings | |
11605 Vimy Ridge Road | |
Alexander, AR 72002 | |
United States | |
501-235-9148 |
Facility : Alexander, AR
Protective (Barrier) Materials
Water | Water | |||
Water Contact | Contact | Contact | ||
Trade Designation | Size Restriction | Temp | Material | |
Coatings - Fittings |
||||
Amercoat 133[1] | >= 4" | CLD 23 | EPOXY | |
Amercoat 133/Amercoat 333[2] | >= 4" | CLD 23 | EPOXY | |
[1] Colors: Oxide red, white Number of Coats: 1-2 Maximum Field Use Dry Film Thickness (in mils): 6 per coat; 10 total Recoat Cure Time and Temperature: 24 hours at 75°F Final Cure and Temperature: 14 days at 75°F Special Comments: Mix ratio of resin to cure is 4:1 by volume. Mix for 5 minutes, let stand for 10 minutes, then remix for 2-3 minutes before application. Scrape the sides of the can while mixing. [2] Colors: Primer: Tank Primer Green, white; Topcoat: Buff, IM gray, off-white, tank pale blue Number of Coats: 2 Sequence of Coats: 1. Amercoat 133 (primer) 2. Amercoat 333 (topcoat) Maximum Field Use Dry Film Thickness (in mils): 133: 4-8 per coat 333: 10-12 per coat; 20 total for 133/333 system. Recoat Cure Time and Temperature: 24 hours at 75°F Final Cure Time and Temperature: 14 days at 75°F Special Comments: The mix ratio is 22 parts base to 3 parts cure by weight. Mix for 5 minutes, let stand for 10 minutes, then remix for 2-3 minutes before application. Scrape the sides of the can while mixing. |
||||
Coatings - Pipe |
||||
Amercoat 133[1] | >= 30" | CLD 23 | EPOXY | |
Amercoat 133/Amercoat 333[2] | >= 12" | CLD 23 | EPOXY | |
Amerlock 2[3] | >= 48" | CLD 23 | EPOXY | |
Novaguard 810[4] | [5] | CLD 23 | EPOXY | |
Novaguard 810ER[4] | [5] | CLD 23 | EPOXY | |
Novaguard 840[13] | >= 36" | CLD 23 | EPOXY | |
Novaguard 840 Filler[14] | [15] | CLD 23 | EPOXY | |
[1] Colors: Oxide red, white Number of Coats: 1-2 Maximum Field Use Dry Film Thickness (in mils): 6 per coat; 10 total Recoat Cure Time and Temperature: 24 hours at 75°F Final Cure and Temperature: 14 days at 75°F Special Comments: Mix ratio of resin to cure is 4:1 by volume. Mix for 5 minutes, let stand for 10 minutes, then remix for 2-3 minutes before application. Scrape the sides of the can while mixing. [2] Colors: Primer: Tank Primer Green, white; Topcoat: Buff, IM gray, off-white, tank pale blue Number of Coats: 2 Sequence of Coats: 1. Amercoat 133 (primer) 2. Amercoat 333 (topcoat) Maximum Field Use Dry Film Thickness (in mils): 133: 4-8 per coat 333: 10-12 per coat; 20 total for 133/333 system. Recoat Cure Time and Temperature: 24 hours at 75°F Final Cure Time and Temperature: 14 days at 75°F Special Comments: The mix ratio is 22 parts base to 3 parts cure by weight. Mix for 5 minutes, let stand for 10 minutes, then remix for 2-3 minutes before application. Scrape the sides of the can while mixing. [3] Colors: Ivory, White, Medium Gray, RT-1805 Blue, Oxide Red, Black Number of Coats: 2-4 Sequence of Coats: Any combination of listed colors Maximum Field Use Dry Thickness: 8 mils per coat; 18 mils total Maximum Thinner: 12% Amercoat #8 by volume (optional use is limited to tanks >= 250,000 gallons) Recoat Cure Time and Temperature: 24 hours at 72° F Final Cure Time/Temperature: 10 days at 72° F for all end uses except tank >= 250,000 gallons which has a final cure of 7 days at 72° F Special Comments: Mix ratio of Base:Cure is 1:1 by volume or 1.1:1 by weight. Use of Amercoat #8 Thinner is limited to tanks of 250,000 gallons or greater. Final Cure Temp: 10 days at 72° F for all end uses without thinner; 7 days at 72° F for tanks >= 250,000 gallons with Amercoat #8 thinner [4] Number of Coats: 1-2 Maximum Field Use Dry Film Thickness (in mils): 30 Recoat Cure Time and Temperature: 24 hours at 70°F Final Cure Time and Temperature: See Listing Note. [5] Certified for tanks >= 500 gallons, pipe >=22", and valves >=2" with a final cure of 72 hours @ 77º F and tanks >= 250,000 gallons and valves >= 3/4" with a final cure of 10 days at 40º F. [13] Colors: Cream, Green Number of Coats: 1-2 Maximum field use dry film thickness (in mils): 30 Recoat cure time and temperature: 24 hours at 70°F Final cure time and temperature: 72 hours at 70°F Special Comments: Mix ratio of base to hardener is 4:1 by volume [14] Colors: Cream, Green Number of Coats: 1 Maximum field use dry film thickness (in mils): 80 Final cure time and temperature: 72 hours at 70°F Special Comments: Novaguard 840: Mix ratio of base to hardener is 4:1 by volume. Mix for 5 minutes, let stand for 10 minutes, then remix for 2-3 minutes before application. Scrape the sides of the can while mixing. After mixing Novaguard 840, add Amercoat 884 up to 1 pound per gallon. [15] Certified for a maximum of 25% of the surface area of a 500 gallon tank and greater and 22" pipe and greater. |
||||
Coatings - Pump |
||||
Amerlock 2[3] | >= 4" | CLD 23 | EPOXY | |
[3] Colors: Ivory, White, Medium Gray, RT-1805 Blue, Oxide Red, Black Number of Coats: 2-4 Sequence of Coats: Any combination of listed colors Maximum Field Use Dry Thickness: 8 mils per coat; 18 mils total Maximum Thinner: 12% Amercoat #8 by volume (optional use is limited to tanks >= 250,000 gallons) Recoat Cure Time and Temperature: 24 hours at 72° F Final Cure Time/Temperature: 10 days at 72° F for all end uses except tank >= 250,000 gallons which has a final cure of 7 days at 72° F Special Comments: Mix ratio of Base:Cure is 1:1 by volume or 1.1:1 by weight. Use of Amercoat #8 Thinner is limited to tanks of 250,000 gallons or greater. Final Cure Temp: 10 days at 72° F for all end uses without thinner; 7 days at 72° F for tanks >= 250,000 gallons with Amercoat #8 thinner |
||||
Coatings - Tank |
||||
Novaguard 840 Filler[14] | [15] | CLD 23 | EPOXY | |
Amercoat 133[1] | >= 50 gal. | CLD 23 | EPOXY | |
Amercoat 133/Amercoat 333[2] | >= 500 gal. | CLD 23 | EPOXY | |
Amercoat 133 + 884 Additive[6] | [7] | CLD 23 | EPOXY | |
Amerlock 2[3] | >= 40,000 gal. | CLD 23 | EPOXY | |
Amercoat 68HS[8] | >= 5000 gal. | CLD 23 | EPOXY | |
Amercoat 68PW[8] | >= 5,000 gal | CLD 23 | EPOXY | |
Novaguard 810[4] | [5] | CLD 23 | EPOXY | |
Novaguard 810ER[4] | [5] | CLD 23 | EPOXY | |
Novaguard 840[13] | >= 1500 gal. | CLD 23 | EPOXY | |
[1] Colors: Oxide red, white Number of Coats: 1-2 Maximum Field Use Dry Film Thickness (in mils): 6 per coat; 10 total Recoat Cure Time and Temperature: 24 hours at 75°F Final Cure and Temperature: 14 days at 75°F Special Comments: Mix ratio of resin to cure is 4:1 by volume. Mix for 5 minutes, let stand for 10 minutes, then remix for 2-3 minutes before application. Scrape the sides of the can while mixing. [2] Colors: Primer: Tank Primer Green, white; Topcoat: Buff, IM gray, off-white, tank pale blue Number of Coats: 2 Sequence of Coats: 1. Amercoat 133 (primer) 2. Amercoat 333 (topcoat) Maximum Field Use Dry Film Thickness (in mils): 133: 4-8 per coat 333: 10-12 per coat; 20 total for 133/333 system. Recoat Cure Time and Temperature: 24 hours at 75°F Final Cure Time and Temperature: 14 days at 75°F Special Comments: The mix ratio is 22 parts base to 3 parts cure by weight. Mix for 5 minutes, let stand for 10 minutes, then remix for 2-3 minutes before application. Scrape the sides of the can while mixing. [3] Colors: Ivory, White, Medium Gray, RT-1805 Blue, Oxide Red, Black Number of Coats: 2-4 Sequence of Coats: Any combination of listed colors Maximum Field Use Dry Thickness: 8 mils per coat; 18 mils total Maximum Thinner: 12% Amercoat #8 by volume (optional use is limited to tanks >= 250,000 gallons) Recoat Cure Time and Temperature: 24 hours at 72° F Final Cure Time/Temperature: 10 days at 72° F for all end uses except tank >= 250,000 gallons which has a final cure of 7 days at 72° F Special Comments: Mix ratio of Base:Cure is 1:1 by volume or 1.1:1 by weight. Use of Amercoat #8 Thinner is limited to tanks of 250,000 gallons or greater. Final Cure Temp: 10 days at 72° F for all end uses without thinner; 7 days at 72° F for tanks >= 250,000 gallons with Amercoat #8 thinner [4] Number of Coats: 1-2 Maximum Field Use Dry Film Thickness (in mils): 30 Recoat Cure Time and Temperature: 24 hours at 70°F Final Cure Time and Temperature: See Listing Note. [5] Certified for tanks >= 500 gallons, pipe >=22", and valves >=2" with a final cure of 72 hours @ 77º F and tanks >= 250,000 gallons and valves >= 3/4" with a final cure of 10 days at 40º F. [6] Number of Coats: 1 Maximum Field Use Dry Film Thickness (in mils): 10 dry film thickness in a skim coat over pitted steel Maximum Thinner: None Final Cure Time and Temperature: 7 days at 70ºF (>=250,000 gallon tank), 10 days at 70ºF (< 250,000 gallons) Special Comments: Amercoat 133: Mix ratio of resin to cure is 4:1 by volume. Mix for 5 minutes, let stand for 10 minutes, then remix for 2-3 minutes before application. Scrape the sides of the can while mixing. After mixing Amercoat 133, add Amercoat 884 at up to 0.5 lb. per gallon. [7] Certified for a maximum of 10% of the surface area of a 500 gallon tank. [8] Colors: Reddish Gray, Green Number of coats: 1 Sequence of coats: Primer Maximum field use dry film thickness: 4 mils Maximum thinner: 6% Amercoat 65 Final Cure Time and temperature: 8 hours at 75°F Special comments: Mix ratio is 3.02:1.00:13.01 (Part A:PartB:Powder) by weight. Any certified PPG top coat may be used provided both primer and topcoat meet their individual Certified end uses. [13] Colors: Cream, Green Number of Coats: 1-2 Maximum field use dry film thickness (in mils): 30 Recoat cure time and temperature: 24 hours at 70°F Final cure time and temperature: 72 hours at 70°F Special Comments: Mix ratio of base to hardener is 4:1 by volume [14] Colors: Cream, Green Number of Coats: 1 Maximum field use dry film thickness (in mils): 80 Final cure time and temperature: 72 hours at 70°F Special Comments: Novaguard 840: Mix ratio of base to hardener is 4:1 by volume. Mix for 5 minutes, let stand for 10 minutes, then remix for 2-3 minutes before application. Scrape the sides of the can while mixing. After mixing Novaguard 840, add Amercoat 884 up to 1 pound per gallon. [15] Certified for a maximum of 25% of the surface area of a 500 gallon tank and greater and 22" pipe and greater. |
||||
Coatings - Valve |
||||
Amercoat 133[1] | >= 4" | CLD 23 | EPOXY | |
Amercoat 133/Amercoat 333[2] | >= 4" | CLD 23 | EPOXY | |
Amerlock 2[3] | >= 6" | CLD 23 | EPOXY | |
Amercoat 370[9] | >= 4" | CLD 23 | EPOXY | |
Amerlock 400[10] | >= 6" | CLD 23 | EPOXY | |
Novaguard 810[4] | [5] | CLD 23 | EPOXY | |
Novaguard 810ER[4] | [5] | CLD 23 | EPOXY | |
Novaguard 840[13] | >= 4" | CLD 23 | EPOXY | |
[1] Colors: Oxide red, white Number of Coats: 1-2 Maximum Field Use Dry Film Thickness (in mils): 6 per coat; 10 total Recoat Cure Time and Temperature: 24 hours at 75°F Final Cure and Temperature: 14 days at 75°F Special Comments: Mix ratio of resin to cure is 4:1 by volume. Mix for 5 minutes, let stand for 10 minutes, then remix for 2-3 minutes before application. Scrape the sides of the can while mixing. [2] Colors: Primer: Tank Primer Green, white; Topcoat: Buff, IM gray, off-white, tank pale blue Number of Coats: 2 Sequence of Coats: 1. Amercoat 133 (primer) 2. Amercoat 333 (topcoat) Maximum Field Use Dry Film Thickness (in mils): 133: 4-8 per coat 333: 10-12 per coat; 20 total for 133/333 system. Recoat Cure Time and Temperature: 24 hours at 75°F Final Cure Time and Temperature: 14 days at 75°F Special Comments: The mix ratio is 22 parts base to 3 parts cure by weight. Mix for 5 minutes, let stand for 10 minutes, then remix for 2-3 minutes before application. Scrape the sides of the can while mixing. [3] Colors: Ivory, White, Medium Gray, RT-1805 Blue, Oxide Red, Black Number of Coats: 2-4 Sequence of Coats: Any combination of listed colors Maximum Field Use Dry Thickness: 8 mils per coat; 18 mils total Maximum Thinner: 12% Amercoat #8 by volume (optional use is limited to tanks >= 250,000 gallons) Recoat Cure Time and Temperature: 24 hours at 72° F Final Cure Time/Temperature: 10 days at 72° F for all end uses except tank >= 250,000 gallons which has a final cure of 7 days at 72° F Special Comments: Mix ratio of Base:Cure is 1:1 by volume or 1.1:1 by weight. Use of Amercoat #8 Thinner is limited to tanks of 250,000 gallons or greater. Final Cure Temp: 10 days at 72° F for all end uses without thinner; 7 days at 72° F for tanks >= 250,000 gallons with Amercoat #8 thinner [4] Number of Coats: 1-2 Maximum Field Use Dry Film Thickness (in mils): 30 Recoat Cure Time and Temperature: 24 hours at 70°F Final Cure Time and Temperature: See Listing Note. [5] Certified for tanks >= 500 gallons, pipe >=22", and valves >=2" with a final cure of 72 hours @ 77º F and tanks >= 250,000 gallons and valves >= 3/4" with a final cure of 10 days at 40º F. [9] Colors: Black, light buff, oxide red, milliken blue, white Number of Coats: 2-4 Maximum Field Use Dry Film Thickness (in mils): 24 Maximum Thinner: 12.5% Amercoat #65 Thinner Recoat Cure Time and Temperature: 0.5 hours at 23°C Final Cure Time and Temperature: 7 days at 23°C Special Comments: Mix ratio of base:cure is 4:1 by volume. [10] Colors: Ivory, medium gray, oxide red, RT-1805, white Number of Coats: 2-4 Sequence of Coats: Any combination of Listed colors Maximum Field Use Dry Film Thickness (in mils): 6 per coat; 18 total Maximum Thinner: 12.5% Amercoat #65 by volume Recoat Cure Time and Temperature: 24 hours at 75°F Final Cure Time and Temperature: 7 days at 75°F Special Comments: Mix ratio of base:cure is 1:1 by volume. [13] Colors: Cream, Green Number of Coats: 1-2 Maximum field use dry film thickness (in mils): 30 Recoat cure time and temperature: 24 hours at 70°F Final cure time and temperature: 72 hours at 70°F Special Comments: Mix ratio of base to hardener is 4:1 by volume |
||||
Primers[11] [12] |
||||
Sigmaweld 199 US | >= 900 gal. | CLD 23 | ZINC | |
[11] This primer may be used with any Certified PPG topcoat provided both primer and topcoat meet their individual Certified end uses. [12] Colors: Tan Number of Coats: 1 Maximum Field Use Dry Film Thickness (in mils): 1 Maximum Thinner: None Recoat Cure Time and Temperature: Not Applicable Final Cure Time and Temperature: Primer (cure before application of topcoat) - 7 days at ambient temperature (20°C) Special Comments: Mix ratio of binder:paste is 2:1 by volume. Apply to steel substrate. |
Facility : Waller, TX
Protective (Barrier) Materials
Water | Water | |||
Water Contact | Contact | Contact | ||
Trade Designation | Size Restriction | Temp | Material | |
Coatings - Pipe[1] [2] |
||||
Amerlock® 2/400 VOC | >= 42" | CLD 23 | EPOXY | |
[1] Colors: Pearl Gray, White and Buff Number of Coats: 2-3 Maximum Field Use Dry Thickness: 18 mil (4-6 mils per coat) Maximum Thinner: 7.5% PPG 97-739 Recoat Cure Time/Temperature: 24 hours at 70F Final Cure Time/Temperature: 7 days at 70F Special Comments: Mix ratio of Base:Cure is 1:1 by volume. Induction period is 12 minutes. [2] Only products bearing the NSF Mark on the product, product packaging, and/or documentation shipped with the product are Certified. |
||||
Coatings - Tank[1] [2] |
||||
Amerlock® 2/400 VOC | >= 50,000 gal. | CLD 23 | EPOXY | |
[1] Colors: Pearl Gray, White and Buff Number of Coats: 2-3 Maximum Field Use Dry Thickness: 18 mil (4-6 mils per coat) Maximum Thinner: 7.5% PPG 97-739 Recoat Cure Time/Temperature: 24 hours at 70F Final Cure Time/Temperature: 7 days at 70F Special Comments: Mix ratio of Base:Cure is 1:1 by volume. Induction period is 12 minutes. [2] Only products bearing the NSF Mark on the product, product packaging, and/or documentation shipped with the product are Certified. |
Number of matching Manufacturers is 1
Number of matching Products is 31
Processing time was 0 seconds