NSF Product and Service Listings

These NSF Official Listings are current as of Thursday, June 27, 2019 at 12:15 a.m. Eastern Time. Please contact NSF to confirm the status of any Listing, report errors, or make suggestions.

Alert: NSF is concerned about fraudulent downloading and manipulation of website text. Always confirm this information by clicking on the below link for the most accurate information: http://info.nsf.org/Certified/PwsComponents/Listings.asp?Company=03240&Standard=061&



NSF/ANSI 61
Drinking Water System Components - Health Effects

NOTE: Unless otherwise indicated for Materials, Certification is only for the Water Contact Material shown in the Listing. Click here for a list of Abbreviations used in these Listings. Click here for the definitions of Water Contact Temperatures denoted in these Listings.


 
LifeLast, Inc. 
3813 Helios Way
Suite 190 
Pflugerville, TX 78660 
United States 
512.628.2112
Visit this company's website


Facility : # 1 USA

Protective (Barrier) Materials

    Water Water
  Water Contact Contact Contact
Trade Designation Size Restriction Temp Material

Coatings - Fittings
DuraShield 110-61[1] >= 1" CLD 23 PUR
DuraShield 210-61[2] >= 2" CLD 23 PUR
DuraShield 310-61[2] >= 2" CLD 23 PUR

[1] Colors: Almond, black, gray, blue, yellow, green, red, brown, purple and variations of
    all of these primary colors.
    Number of Coats: Unlimited
    Maximum Field Use Dry Film Thickness (in mils): 250
    Final Cure Time and Temperature: 24 hours at 70°F
    Special Comments: The coating may be applied in as many coats as necessary up to a
    maximum dry filim thickness of 250 mils. Mix ratio of polyol to
    isocyanate is 1:1 by volume. Minimum field use dry film thickness is 20 mils.
[2] Colors: Almond, Black, Gray
    Number of Coats: 1
    Maximum Field Use Dry Film Thickness (in mils): 250
    Final Cure Time and Temperature: 72 hours at 75°F
    Special Comments: Mix ratio of Part A:Part B of 210-61 is 2:1 by volume and mix ratio of
    Part A:Part B of 310-61 is 3:1 by volume. Minimum certified field use dry film thickness
    is 20 mils.

Coatings - Pipe
DuraShield 110-61[1] >= 1" CLD 23 PUR
DuraShield 210-61[2] >= 8" CLD 23 PUR
DuraShield 310-61[2] >= 8" CLD 23 PUR

[1] Colors: Almond, black, gray, blue, yellow, green, red, brown, purple and variations of
    all of these primary colors.
    Number of Coats: Unlimited
    Maximum Field Use Dry Film Thickness (in mils): 250
    Final Cure Time and Temperature: 24 hours at 70°F
    Special Comments: The coating may be applied in as many coats as necessary up to a
    maximum dry filim thickness of 250 mils. Mix ratio of polyol to
    isocyanate is 1:1 by volume. Minimum field use dry film thickness is 20 mils.
[2] Colors: Almond, Black, Gray
    Number of Coats: 1
    Maximum Field Use Dry Film Thickness (in mils): 250
    Final Cure Time and Temperature: 72 hours at 75°F
    Special Comments: Mix ratio of Part A:Part B of 210-61 is 2:1 by volume and mix ratio of
    Part A:Part B of 310-61 is 3:1 by volume. Minimum certified field use dry film thickness
    is 20 mils.

Coatings - Tank
DuraShield 110-61[1] >= 50 gal. CLD 23 PUR
DuraShield 210-61[2] >= 50 gal. CLD 23 PUR
DuraShield 310-61[2] >= 50 gal. CLD 23 PUR

[1] Colors: Almond, black, gray, blue, yellow, green, red, brown, purple and variations of
    all of these primary colors.
    Number of Coats: Unlimited
    Maximum Field Use Dry Film Thickness (in mils): 250
    Final Cure Time and Temperature: 24 hours at 70°F
    Special Comments: The coating may be applied in as many coats as necessary up to a
    maximum dry filim thickness of 250 mils. Mix ratio of polyol to
    isocyanate is 1:1 by volume. Minimum field use dry film thickness is 20 mils.
[2] Colors: Almond, Black, Gray
    Number of Coats: 1
    Maximum Field Use Dry Film Thickness (in mils): 250
    Final Cure Time and Temperature: 72 hours at 75°F
    Special Comments: Mix ratio of Part A:Part B of 210-61 is 2:1 by volume and mix ratio of
    Part A:Part B of 310-61 is 3:1 by volume. Minimum certified field use dry film thickness
    is 20 mils.

Coatings - Valve
DuraShield 110-61[1] >= 1" CLD 23 PUR
DuraShield 210-61[2] >= 2" CLD 23 PUR
DuraShield 310-61[2] >= 2" CLD 23 PUR

[1] Colors: Almond, black, gray, blue, yellow, green, red, brown, purple and variations of
    all of these primary colors.
    Number of Coats: Unlimited
    Maximum Field Use Dry Film Thickness (in mils): 250
    Final Cure Time and Temperature: 24 hours at 70°F
    Special Comments: The coating may be applied in as many coats as necessary up to a
    maximum dry filim thickness of 250 mils. Mix ratio of polyol to
    isocyanate is 1:1 by volume. Minimum field use dry film thickness is 20 mils.
[2] Colors: Almond, Black, Gray
    Number of Coats: 1
    Maximum Field Use Dry Film Thickness (in mils): 250
    Final Cure Time and Temperature: 72 hours at 75°F
    Special Comments: Mix ratio of Part A:Part B of 210-61 is 2:1 by volume and mix ratio of
    Part A:Part B of 310-61 is 3:1 by volume. Minimum certified field use dry film thickness
    is 20 mils.


Number of matching Manufacturers is 1
Number of matching Products is 12
Processing time was 0 seconds