NSF Product and Service Listings

These NSF Official Listings are current as of Friday, May 17, 2024 at 12:15 a.m. Eastern Time. Please contact NSF to confirm the status of any Listing, report errors, or make suggestions.

Alert: NSF is concerned about fraudulent downloading and manipulation of website text. Always confirm this information by clicking on the below link for the most accurate information: http://info.nsf.org/Certified/PwsComponents/Listings.asp?Company=04030&Standard=061&


NSF/ANSI/CAN 61
Drinking Water System Components - Health Effects

NOTE: Unless otherwise indicated for Materials, Certification is only for the Water Contact Material shown in the Listing. Click here for a list of Abbreviations used in these Listings. Click here for the definitions of Water Contact Temperatures denoted in these Listings. Products certified to NSF/ANSI/CAN 61 comply with the health effects criteria in NSF/ANSI/CAN 600.

 
Arkema Inc. 
Technical Polymers
900 First Avenue 
King of Prussia, PA 19406 
United States 
800-321-5196 
610-207-7000
Visit this company's website


Facility : Birdsboro, PA

Potable Water Materials

    Water Water
    Contact Contact
Trade Designation End Use Temp Material

Potable Water Materials
Rilsan (R) Besno Polyamide[1] A C. HOT NP 

[1] Certified for a maximum surface area to volume ratio of 24 sq. in./L.



Facility : Saint-Pal-de-Mons, France

Potable Water Materials

    Water Water
    Contact Contact
Trade Designation End Use Temp Material

Material
2 RILSAN BZM 30 O TLDA F C. HOT RNP



Facility : Serquigny, France

Protective (Barrier) Materials

    Water Water
  Water Contact Contact Contact
Trade Designation Size Restriction Temp Material

Coatings - Fittings
RILSAN® PA 11 T BLACK 7450 AC[1] >= 2" CLD 23 NP
RILSAN® PA 11 T BLUE 7443 MAC[2] >= 2" CLD 23 NP
RILSAN® PA 11 T GREY 5161 MAC[3] >= 2" CLD 23 NP
Rilsan® 1488 White AC FB[4] >= 2" CLD 23 NP
Rilsan® PA 11 T White 1488 AC[4] >= 2" CLD 23 NP 

[1] Colors: Black
    Number of Coats: 2
    Sequence of Coats: Primer: Rilprim P23 V40 or Primgreen LAT 12035; Topcoat: Listed
    Product
    Maximum Field Use Dry Film Thickness (in mils): Primer: 0.5; Topcoat: 20
    Maximum Thinner: None
    Recoat Cure Time and Temperature: 30 minutes at 20ºC followed by 8 minutes at 330ºC
    Final Cure Time and Temperature: None (see special comments)
    Special Comments: Ensure substrate is free of oil or any contaminants. Apply uniform
    layer of primer (pneumatic gun application). Primer dries in 30 minutes at 20ºC. Primer
    Target DFT = 0.5 mils. Then heat substrate for 8 minutes at 330ºC. Quickly convey and
    then dip panel into fluidized bed for 3 seconds, while shaking. Powder Target DFT = 10 -
    20 mils. Cool down at ambient air, 20ºC.
[2] Colors: Blue
    Number of Coats: 2
    Sequence of Coats: (1) Primgreen™ LAT 12035 or Rilprim P23V40 (2) Listed product
    Maximum Field Use Dry Film Thickness (in mils): 0.5 (primer); 28 (topcoat)
    Maximum Thinner: None
    Recoat Cure Time and Temperature: Primer: 30 minutes at ambient; Topcoat: 20 minute
    preheat of primed panels at 290°C
    Final Cure Time and Temperature: 1 minute 30 secs at 220°C to post fuse the remainder of
    the panel.
    Primgreen LAT 12035 primer is authorized for use in pipes 6" and greater, fittings 2"
    and greater, and valves 2" and greater.
[3] Colors: Grey
    Number of Coats: 2
    Sequence of Coats: Primgreen LAT 12035 then listed product
    Maximum Field Use Dry Film Thickness (in mils): 0.5 (primer); 20 (topcoat)
    Maximum Thinner: N/A
    Recoat Cure Time and Temperature: 30 minutes at 20ºC followed by 8 minutes at 330ºC
    Final Cure Time and Temperature: None (see special comments)
    Special Comments: Ensure substrate is free of oil or any contaminants. Apply uniform
    layer of primer (pneumatic gun application). Primer dries in 30 minutes at 20ºC. Primer
    Target DFT = 0.5 mils. Heat substrate 8 minutes at 330ºC. Quickly convey and then dip
    panel into fluidized bed during 3 sec, while shaking. Powder Target DFT = 10 - 20 mil.
    Cool down at ambient air, 20ºC.
[4] Colors: White
    Number of Coats:  2
    Sequence of Coats:  Primer:  Primgreen LAT 12035; Topcoat: Listed Product
    Maximum Field Use Dry Film Thickness (in mils):  Primer: 0.5; Topcoat: 20
    Recoat Cure Time and Temperature:  30 minutes at 20°C followed by 8 minutes at 330°C
    Final Cure Time and Temperature:  None (see special comments)
    Special Comments:  Ensure substrate is free of oil or any contaminants.  Apply uniform
    layer of primer (pneumatic gun application).  Primer dries in 30 minutes at 20°C.  Heat
    substrate 8 minutes at 330°C.  Quickly convey and then dip panel into fluidized bed for
    3 sec, while shaking.  Cool down at ambient air, 20°C.

Coatings - Pipe
RILSAN® PA 11 T BLACK 7450 AC[1] >= 2" CLD 23 NP
RILSAN® PA 11 T BLUE 7443 MAC[2] >= 2" CLD 23 NP
RILSAN® PA 11 T GREY 5161 MAC[3] >= 6" CLD 23 NP
Rilsan® 1488 White AC FB[4] >= 2" CLD 23 NP
Rilsan® PA 11 T White 1488 AC[4] >= 2" CLD 23 NP 

[1] Colors: Black
    Number of Coats: 2
    Sequence of Coats: Primer: Rilprim P23 V40 or Primgreen LAT 12035; Topcoat: Listed
    Product
    Maximum Field Use Dry Film Thickness (in mils): Primer: 0.5; Topcoat: 20
    Maximum Thinner: None
    Recoat Cure Time and Temperature: 30 minutes at 20ºC followed by 8 minutes at 330ºC
    Final Cure Time and Temperature: None (see special comments)
    Special Comments: Ensure substrate is free of oil or any contaminants. Apply uniform
    layer of primer (pneumatic gun application). Primer dries in 30 minutes at 20ºC. Primer
    Target DFT = 0.5 mils. Then heat substrate for 8 minutes at 330ºC. Quickly convey and
    then dip panel into fluidized bed for 3 seconds, while shaking. Powder Target DFT = 10 -
    20 mils. Cool down at ambient air, 20ºC.
[2] Colors: Blue
    Number of Coats: 2
    Sequence of Coats: (1) Primgreen™ LAT 12035 or Rilprim P23V40 (2) Listed product
    Maximum Field Use Dry Film Thickness (in mils): 0.5 (primer); 28 (topcoat)
    Maximum Thinner: None
    Recoat Cure Time and Temperature: Primer: 30 minutes at ambient; Topcoat: 20 minute
    preheat of primed panels at 290°C
    Final Cure Time and Temperature: 1 minute 30 secs at 220°C to post fuse the remainder of
    the panel.
    Primgreen LAT 12035 primer is authorized for use in pipes 6" and greater, fittings 2"
    and greater, and valves 2" and greater.
[3] Colors: Grey
    Number of Coats: 2
    Sequence of Coats: Primgreen LAT 12035 then listed product
    Maximum Field Use Dry Film Thickness (in mils): 0.5 (primer); 20 (topcoat)
    Maximum Thinner: N/A
    Recoat Cure Time and Temperature: 30 minutes at 20ºC followed by 8 minutes at 330ºC
    Final Cure Time and Temperature: None (see special comments)
    Special Comments: Ensure substrate is free of oil or any contaminants. Apply uniform
    layer of primer (pneumatic gun application). Primer dries in 30 minutes at 20ºC. Primer
    Target DFT = 0.5 mils. Heat substrate 8 minutes at 330ºC. Quickly convey and then dip
    panel into fluidized bed during 3 sec, while shaking. Powder Target DFT = 10 - 20 mil.
    Cool down at ambient air, 20ºC.
[4] Colors: White
    Number of Coats:  2
    Sequence of Coats:  Primer:  Primgreen LAT 12035; Topcoat: Listed Product
    Maximum Field Use Dry Film Thickness (in mils):  Primer: 0.5; Topcoat: 20
    Recoat Cure Time and Temperature:  30 minutes at 20°C followed by 8 minutes at 330°C
    Final Cure Time and Temperature:  None (see special comments)
    Special Comments:  Ensure substrate is free of oil or any contaminants.  Apply uniform
    layer of primer (pneumatic gun application).  Primer dries in 30 minutes at 20°C.  Heat
    substrate 8 minutes at 330°C.  Quickly convey and then dip panel into fluidized bed for
    3 sec, while shaking.  Cool down at ambient air, 20°C.

Coatings - Tank
RILSAN® PA 11 ES White 1464 EC[5] >= 7,500,000 C. HOT NP 

[5] Colors: 1464 White
    Number of Coats: 2
    Sequence of Coats: Primer: Rilprim LES 201 and Rilprim 104 B RC 7; Topcoat: Listed
    Product
    Maximum Field Use Dry Film Thickness (in mils): Primer: 0.4; Topcoat: 6
    Recoat Cure Time and Temperature: 15 minutes at 20ºC
    Final Cure Time and Temperature: 5 minutes at 215ºC, Cool down at ambient air, 20ºC
    Special Comments: Ensure substrate is free of oil or any contaminants. Stir primer part
    A until resin is dispersed, then mix with part B. Wait 30 minutes before use and keep
    stirring (8 hours pot life). Apply uniform layer of primer (pneumatic gun app.). Primer
    dries 15 minutes at 20ºC. Primer Target DFT = 0.4 mils. Coat substrate (layer 2) with
    tribo or positive corona gun (+30 - 50 kV). Target Powder DFT = 4 - 6 mils
    (electrostatic app.). The mix ratio of Rilprim LES 201 to Rilprim 104 B RC 7 is 1:1 by
    volume or 1.2:1 by weight.

Coatings - Valve
RILSAN® PA 11 T BLACK 7450 AC[1] >= 2" CLD 23 NP
RILSAN® PA 11 T BLUE 7443 MAC[2] >= 2" CLD 23 NP
RILSAN® PA 11 T GREY 5161 MAC[3] >= 2" CLD 23 NP
Rilsan® 1488 White AC FB[4] >= 2" CLD 23 NP
Rilsan® PA 11 T White 1488 AC[4] >= 2" CLD 23 NP 

[1] Colors: Black
    Number of Coats: 2
    Sequence of Coats: Primer: Rilprim P23 V40 or Primgreen LAT 12035; Topcoat: Listed
    Product
    Maximum Field Use Dry Film Thickness (in mils): Primer: 0.5; Topcoat: 20
    Maximum Thinner: None
    Recoat Cure Time and Temperature: 30 minutes at 20ºC followed by 8 minutes at 330ºC
    Final Cure Time and Temperature: None (see special comments)
    Special Comments: Ensure substrate is free of oil or any contaminants. Apply uniform
    layer of primer (pneumatic gun application). Primer dries in 30 minutes at 20ºC. Primer
    Target DFT = 0.5 mils. Then heat substrate for 8 minutes at 330ºC. Quickly convey and
    then dip panel into fluidized bed for 3 seconds, while shaking. Powder Target DFT = 10 -
    20 mils. Cool down at ambient air, 20ºC.
[2] Colors: Blue
    Number of Coats: 2
    Sequence of Coats: (1) Primgreen™ LAT 12035 or Rilprim P23V40 (2) Listed product
    Maximum Field Use Dry Film Thickness (in mils): 0.5 (primer); 28 (topcoat)
    Maximum Thinner: None
    Recoat Cure Time and Temperature: Primer: 30 minutes at ambient; Topcoat: 20 minute
    preheat of primed panels at 290°C
    Final Cure Time and Temperature: 1 minute 30 secs at 220°C to post fuse the remainder of
    the panel.
    Primgreen LAT 12035 primer is authorized for use in pipes 6" and greater, fittings 2"
    and greater, and valves 2" and greater.
[3] Colors: Grey
    Number of Coats: 2
    Sequence of Coats: Primgreen LAT 12035 then listed product
    Maximum Field Use Dry Film Thickness (in mils): 0.5 (primer); 20 (topcoat)
    Maximum Thinner: N/A
    Recoat Cure Time and Temperature: 30 minutes at 20ºC followed by 8 minutes at 330ºC
    Final Cure Time and Temperature: None (see special comments)
    Special Comments: Ensure substrate is free of oil or any contaminants. Apply uniform
    layer of primer (pneumatic gun application). Primer dries in 30 minutes at 20ºC. Primer
    Target DFT = 0.5 mils. Heat substrate 8 minutes at 330ºC. Quickly convey and then dip
    panel into fluidized bed during 3 sec, while shaking. Powder Target DFT = 10 - 20 mil.
    Cool down at ambient air, 20ºC.
[4] Colors: White
    Number of Coats:  2
    Sequence of Coats:  Primer:  Primgreen LAT 12035; Topcoat: Listed Product
    Maximum Field Use Dry Film Thickness (in mils):  Primer: 0.5; Topcoat: 20
    Recoat Cure Time and Temperature:  30 minutes at 20°C followed by 8 minutes at 330°C
    Final Cure Time and Temperature:  None (see special comments)
    Special Comments:  Ensure substrate is free of oil or any contaminants.  Apply uniform
    layer of primer (pneumatic gun application).  Primer dries in 30 minutes at 20°C.  Heat
    substrate 8 minutes at 330°C.  Quickly convey and then dip panel into fluidized bed for
    3 sec, while shaking.  Cool down at ambient air, 20°C.

Number of matching Manufacturers is 1
Number of matching Products is 18
Processing time was 0 seconds