NSF Product and Service Listings
These NSF Official Listings are current as of Monday, July 22, 2024 at 12:15 a.m. Eastern Time. Please contact NSF to confirm the status of any Listing, report errors, or make suggestions.
Alert: NSF is concerned about fraudulent downloading and manipulation of website text. Always confirm this information by clicking on the below link for the most accurate information: http://info.nsf.org/Certified/PwsComponents/Listings.asp?Company=34570&Standard=061&
NSF/ANSI/CAN 61
Drinking Water System Components - Health Effects
Drinking Water System Components - Health Effects
NOTE: Unless otherwise indicated for Materials, Certification is only for the Water Contact Material shown in the Listing. Click here for a list of Abbreviations used in these Listings. Click here for the definitions of Water Contact Temperatures denoted in these Listings. Products certified to NSF/ANSI/CAN 61 comply with the health effects criteria in NSF/ANSI/CAN 600.
The Euclid Chemical Company | |
3835 State Route 72 | |
Kirkland, IL 60146 | |
United States | |
815-522-3394 | |
Visit this company's website |
Facility : Kirkland, IL
Joining and Sealing Materials
Water | Water | |||
Contact | Contact | |||
Trade Designation | Size | Temp | Material | |
Patching Materials |
||||
Tamms Structural Mortar[1] [2] [3] | [4] | CLD 23 | CMNT | |
[1] Mix ratio is 2.4-3.3 L of water per 50 lb mortar. [2] Certified for a 7 day moist cure at 73 +/- 3 degrees and 100% relative humidity followed by a 1-3 day air cure at 73 +/- 3 degrees and 50% relative humidity. [3] Certification does not include Duralprep AC primer or Eucobar evaporation retarder. [4] Certified for use at a maximum of 50% of tanks 20,000 gallons and greater, 50% of pipes 60" diameter and greater, and 50% of fittings 4" diameter and greater. |
Protective (Barrier) Materials
Water | Water | |||
Water Contact | Contact | Contact | ||
Trade Designation | Size Restriction | Temp | Material | |
Coatings - Fittings[1] |
||||
Tamoseal Gray | >= 4 in | CLD 23 | CMNT | |
Tamoseal Gray N | >= 4 in | CLD 23 | CMNT | |
Tamoseal White | >= 4 in | CLD 23 | CMNT | |
Tamoseal White N | >= 4 in | CLD 23 | CMNT | |
[1] Number Of Coats: 2 Maximium Field Use Dry Thickness(in mils): 125 mils Recoat Cure Time and Temperature: 12 hours at 40°F Final Cure Time/Temperature: 7 days at 40°F Colors: Gray, White Special Comments: Akkro-7T or Flex-Con Additives are mixed 1:3 (Additive:water) as the mixing liquid and then used at 2 gal per 50 lb Tamoseal. Induction time is 10 minutes. |
||||
Coatings - Pipe[1] |
||||
Tamoseal Gray | >= 36 in | CLD 23 | CMNT | |
Tamoseal Gray N | >= 36 in | CLD 23 | CMNT | |
Tamoseal White | >= 36 in | CLD 23 | CMNT | |
Tamoseal White N | >= 36 in | CLD 23 | CMNT | |
[1] Number Of Coats: 2 Maximium Field Use Dry Thickness(in mils): 125 mils Recoat Cure Time and Temperature: 12 hours at 40°F Final Cure Time/Temperature: 7 days at 40°F Colors: Gray, White Special Comments: Akkro-7T or Flex-Con Additives are mixed 1:3 (Additive:water) as the mixing liquid and then used at 2 gal per 50 lb Tamoseal. Induction time is 10 minutes. |
||||
Coatings - Tank |
||||
Hey'Di K-11/Hey'Di SB[2] | >= 1000 gal. | CLD 23 | CMNT | |
Tamoseal Gray[1] | >= 3000 gal. | CLD 23 | CMNT | |
Tamoseal Gray N[1] | >= 3000 gal. | CLD 23 | CMNT | |
Tamoseal Ultra/Tamoseal Ultra Liquid[2] | >= 1000 gal. | CLD 23 | CMNT | |
Tamoseal White[1] | >= 3000 gal. | CLD 23 | CMNT | |
Tamoseal White N[1] | >= 3000 gal. | CLD 23 | CMNT | |
[1] Number Of Coats: 2 Maximium Field Use Dry Thickness(in mils): 125 mils Recoat Cure Time and Temperature: 12 hours at 40°F Final Cure Time/Temperature: 7 days at 40°F Colors: Gray, White Special Comments: Akkro-7T or Flex-Con Additives are mixed 1:3 (Additive:water) as the mixing liquid and then used at 2 gal per 50 lb Tamoseal. Induction time is 10 minutes. [2] Colors: Gray, white Number of Coats: 2 Sequence of Coats: N/A Maximum Field Use Dry Film Thickness (in mils): 60 Maximum Thinner: None Recoat Cure Time and Temperature: 24 hours at 75°F Final Cure Time and Temperature: 7 days at 75°F Special Comments: Apply to concrete at a rate of 0.25 lb. mixed slurry per square foot. Mix 1:5 Hey'Di SB Bonding with water then mix that at 50 lb. Hey'Di K-11 to 2 gallons of mixed SB Bonding. |
Number of matching Manufacturers is 1
Number of matching Products is 15
Processing time was 0 seconds