NSF Product and Service Listings

These NSF Official Listings are current as of Monday, July 22, 2024 at 12:15 a.m. Eastern Time. Please contact NSF to confirm the status of any Listing, report errors, or make suggestions.

Alert: NSF is concerned about fraudulent downloading and manipulation of website text. Always confirm this information by clicking on the below link for the most accurate information: http://info.nsf.org/Certified/PwsComponents/Listings.asp?Company=36620&Standard=061&


NSF/ANSI/CAN 61
Drinking Water System Components - Health Effects

NOTE: Unless otherwise indicated for Materials, Certification is only for the Water Contact Material shown in the Listing. Click here for a list of Abbreviations used in these Listings. Click here for the definitions of Water Contact Temperatures denoted in these Listings. Products certified to NSF/ANSI/CAN 61 comply with the health effects criteria in NSF/ANSI/CAN 600.

 
International Paint Inc. 
Heavy Duty Group
6001 Antoine Drive 
Houston, TX 77210-4806 
United States 
800-525-6824 
713-682-1711
Visit this company's website


Facility : Houston, TX

Protective (Barrier) Materials

    Water Water
  Water Contact Contact Contact
Trade Designation Size Restriction Temp Material

Coatings - Fittings
Bar-Rust 233H Low VOC Buff[1] >= 6" CLD 23 EPOXY
Bar-Rust 233H Low VOC Off-White[1] >= 6" CLD 23 EPOXY
Interline 850[2] >= 2" CLD 23 EPOXY
Interline 975P[3] [4] >= 1/4" CLD 23 EPOXY 

[1] Colors: off-white or buff
    Number of Coats: 2-3
    Maximum Field Use Dry Film Thickness (in mils): 20
    Maximum Thinner: 5% T-0 Zero VOC Thinner by volume
    Recoat Cure Time and Temperature: 24 hours at 77°F
    Final Cure Time and Temperature: 14 days at 77°F
    Special Comments: Mix ratio of A:B is 4:1 by volume and 7.2:1 by weight.
[2] Colors: TLA 850/TLA 856 White, TLA851/TLA 856 Gray, TLA 852/TLA 856 Buff, TLA 72525/TLA
    856 Oxide Red, TLA 855/TLA 856 Cruiser Blue
    Number of Coats: 2
    Maximum Field Use Dry Film Thickness (in mils): 10
    Maximum Thinner: International Thinner GTA 415, 6% by volume
    Recoat Cure Time and Temperature: 16 hours at 75°F
    Final Cure Time and Temperature: 14 days at 75°F
    Special Comments: Mix ratio of Base:Curing Agent is 4:1 by volume.
[3] Colors: Cream, White
    Number of Coats: 1-3
    Maximum Field Use Dry Film Thickness (in mils): 50 (Total)
    Maximum thinner: None
    Final Cure Time and Temperature: 3 days at 77°F
    Special Comments: Mix ratio of Part A:Part B is 2:1 by volume.
[4] Colors: Cream, White
    Number of Coats: 2
    Maximum Field Use Dry Film Thickness (in mils): 25 per coat
    Maximum thinner: None
    Final Cure Time and Temperature: 3 days at 77°F
    Special Comments: Mix ratio of Part A:Part B is 2:1 by volume.

Coatings - Pipe
Interline 850[2] >= 48" CLD 23 EPOXY
Interline 975P[3] [4] >= 2" CLD 23 EPOXY
Intershield 300HS[8] >= 6" CLD 23 EPOXY 

[2] Colors: TLA 850/TLA 856 White, TLA851/TLA 856 Gray, TLA 852/TLA 856 Buff, TLA 72525/TLA
    856 Oxide Red, TLA 855/TLA 856 Cruiser Blue
    Number of Coats: 2
    Maximum Field Use Dry Film Thickness (in mils): 10
    Maximum Thinner: International Thinner GTA 415, 6% by volume
    Recoat Cure Time and Temperature: 16 hours at 75°F
    Final Cure Time and Temperature: 14 days at 75°F
    Special Comments: Mix ratio of Base:Curing Agent is 4:1 by volume.
[3] Colors: Cream, White
    Number of Coats: 1-3
    Maximum Field Use Dry Film Thickness (in mils): 50 (Total)
    Maximum thinner: None
    Final Cure Time and Temperature: 3 days at 77°F
    Special Comments: Mix ratio of Part A:Part B is 2:1 by volume.
[4] Colors: Cream, White
    Number of Coats: 2
    Maximum Field Use Dry Film Thickness (in mils): 25 per coat
    Maximum thinner: None
    Final Cure Time and Temperature: 3 days at 77°F
    Special Comments: Mix ratio of Part A:Part B is 2:1 by volume.
[8] Colors: ENA380 Bronze, ENA381 Aluminum
    Number of Coats: 2
    Sequence of Coats: 2 coats of either color in any combination.
    Maximum Field Use Dry Film Thickness (in mils): 10
    Recoat Cure Time and Temperature: 24 hours at 73°F
    Final Cure Time and Temperature: 30 days at 73°F
    Special Comments: Mix ratio of color base to curing agent is 3.73:1 by weight and 2.5:1
    by volume.

Coatings - Pump
Interline 850[2] >= 2" CLD 23 EPOXY
Interline 975P[3] [4] >= 2" CLD 23 EPOXY
Intershield 300HS[8] >= 2" CLD 23 EPOXY 

[2] Colors: TLA 850/TLA 856 White, TLA851/TLA 856 Gray, TLA 852/TLA 856 Buff, TLA 72525/TLA
    856 Oxide Red, TLA 855/TLA 856 Cruiser Blue
    Number of Coats: 2
    Maximum Field Use Dry Film Thickness (in mils): 10
    Maximum Thinner: International Thinner GTA 415, 6% by volume
    Recoat Cure Time and Temperature: 16 hours at 75°F
    Final Cure Time and Temperature: 14 days at 75°F
    Special Comments: Mix ratio of Base:Curing Agent is 4:1 by volume.
[3] Colors: Cream, White
    Number of Coats: 1-3
    Maximum Field Use Dry Film Thickness (in mils): 50 (Total)
    Maximum thinner: None
    Final Cure Time and Temperature: 3 days at 77°F
    Special Comments: Mix ratio of Part A:Part B is 2:1 by volume.
[4] Colors: Cream, White
    Number of Coats: 2
    Maximum Field Use Dry Film Thickness (in mils): 25 per coat
    Maximum thinner: None
    Final Cure Time and Temperature: 3 days at 77°F
    Special Comments: Mix ratio of Part A:Part B is 2:1 by volume.
[8] Colors: ENA380 Bronze, ENA381 Aluminum
    Number of Coats: 2
    Sequence of Coats: 2 coats of either color in any combination.
    Maximum Field Use Dry Film Thickness (in mils): 10
    Recoat Cure Time and Temperature: 24 hours at 73°F
    Final Cure Time and Temperature: 30 days at 73°F
    Special Comments: Mix ratio of color base to curing agent is 3.73:1 by weight and 2.5:1
    by volume.

Coatings - Tank
Bar-Rust 233H Low VOC Buff[1] >= 500,000 gal. CLD 23 EPOXY
Bar-Rust 233H Low VOC Off-White[1] >= 500,000 gal. CLD 23 EPOXY
Interline 850[2] >= 1500 gal. CLD 23 EPOXY
Interline 975P[3] [4] >= 50 gal. CLD 23 EPOXY
Intershield 300HS[8] >= 1000 gal. CLD 23 EPOXY
Intershield 300V[5] >= 7000 gal. CLD 23 EPOXY 

[1] Colors: off-white or buff
    Number of Coats: 2-3
    Maximum Field Use Dry Film Thickness (in mils): 20
    Maximum Thinner: 5% T-0 Zero VOC Thinner by volume
    Recoat Cure Time and Temperature: 24 hours at 77°F
    Final Cure Time and Temperature: 14 days at 77°F
    Special Comments: Mix ratio of A:B is 4:1 by volume and 7.2:1 by weight.
[2] Colors: TLA 850/TLA 856 White, TLA851/TLA 856 Gray, TLA 852/TLA 856 Buff, TLA 72525/TLA
    856 Oxide Red, TLA 855/TLA 856 Cruiser Blue
    Number of Coats: 2
    Maximum Field Use Dry Film Thickness (in mils): 10
    Maximum Thinner: International Thinner GTA 415, 6% by volume
    Recoat Cure Time and Temperature: 16 hours at 75°F
    Final Cure Time and Temperature: 14 days at 75°F
    Special Comments: Mix ratio of Base:Curing Agent is 4:1 by volume.
[3] Colors: Cream, White
    Number of Coats: 1-3
    Maximum Field Use Dry Film Thickness (in mils): 50 (Total)
    Maximum thinner: None
    Final Cure Time and Temperature: 3 days at 77°F
    Special Comments: Mix ratio of Part A:Part B is 2:1 by volume.
[4] Colors: Cream, White
    Number of Coats: 2
    Maximum Field Use Dry Film Thickness (in mils): 25 per coat
    Maximum thinner: None
    Final Cure Time and Temperature: 3 days at 77°F
    Special Comments: Mix ratio of Part A:Part B is 2:1 by volume.
[5] Colors: ENA310 Bronze; ENA311 Aluminum
    Number of Coats: 2
    Sequence of Coats: Either coating may be used alone or together in any order.
    Maximum Field Use Dry Film Thickness (in mils): 10
    Recoat Cure Time and Temperature: 7 hours at 73°F (minimum)
    Final Cure Time and Temperature: 30 days at 73°F
    Special Comments: Mix ratio of color base:converter is 1:1 by volume.
[8] Colors: ENA380 Bronze, ENA381 Aluminum
    Number of Coats: 2
    Sequence of Coats: 2 coats of either color in any combination.
    Maximum Field Use Dry Film Thickness (in mils): 10
    Recoat Cure Time and Temperature: 24 hours at 73°F
    Final Cure Time and Temperature: 30 days at 73°F
    Special Comments: Mix ratio of color base to curing agent is 3.73:1 by weight and 2.5:1
    by volume.

Coatings - Valve
Bar-Rust 233H Low VOC Buff[1] >= 4" CLD 23 EPOXY
Bar-Rust 233H Low VOC Off-White[1] >= 4" CLD 23 EPOXY
Interline 850[2] >= 4" CLD 23 EPOXY
Interline 975P[3] [4] >= 1/4" CLD 23 EPOXY 

[1] Colors: off-white or buff
    Number of Coats: 2-3
    Maximum Field Use Dry Film Thickness (in mils): 20
    Maximum Thinner: 5% T-0 Zero VOC Thinner by volume
    Recoat Cure Time and Temperature: 24 hours at 77°F
    Final Cure Time and Temperature: 14 days at 77°F
    Special Comments: Mix ratio of A:B is 4:1 by volume and 7.2:1 by weight.
[2] Colors: TLA 850/TLA 856 White, TLA851/TLA 856 Gray, TLA 852/TLA 856 Buff, TLA 72525/TLA
    856 Oxide Red, TLA 855/TLA 856 Cruiser Blue
    Number of Coats: 2
    Maximum Field Use Dry Film Thickness (in mils): 10
    Maximum Thinner: International Thinner GTA 415, 6% by volume
    Recoat Cure Time and Temperature: 16 hours at 75°F
    Final Cure Time and Temperature: 14 days at 75°F
    Special Comments: Mix ratio of Base:Curing Agent is 4:1 by volume.
[3] Colors: Cream, White
    Number of Coats: 1-3
    Maximum Field Use Dry Film Thickness (in mils): 50 (Total)
    Maximum thinner: None
    Final Cure Time and Temperature: 3 days at 77°F
    Special Comments: Mix ratio of Part A:Part B is 2:1 by volume.
[4] Colors: Cream, White
    Number of Coats: 2
    Maximum Field Use Dry Film Thickness (in mils): 25 per coat
    Maximum thinner: None
    Final Cure Time and Temperature: 3 days at 77°F
    Special Comments: Mix ratio of Part A:Part B is 2:1 by volume.

Patching Materials
Interline 975P[6] [7] CLD 23 EPOXY 

[6] Colors: Cream, White
    Number of Coats: 2						
    Sequence of Coats: Pit Filler, Topcoat						
    Maximum Field Use Dry Film Thickness (in mils): 300 (250 Pit Filler, 50 Top Coat)						
    Maximum Thinner: None						
    Recoat Cure Time and Temperature: 16 hours at 77°F						
    Final Cure Time and Temperature: 7 days at 77°F						
    Special Comments: Mix ratio of Part A:B is 2:1 by volume; CABO-SIL TS-720 from Cabot or
    AEROSIL R 202 from Evonik may be added at a maximum of 5% by weight to pit filler layer.
    Pit filler is topcoated with up to 50 mils Interline 975P without silica.
[7] Certified for use as a patching material at 5% coverage of 50 gallon tanks and greater.

Number of matching Manufacturers is 1
Number of matching Products is 21
Processing time was 0 seconds