NSF Product and Service Listings

These NSF Official Listings are current as of Tuesday, September 23, 2014 at 12:15 a.m. Eastern Time. Please contact NSF International to confirm the status of any Listing, report errors, or make suggestions.

Alert: NSF is concerned about fraudulent downloading and manipulation of website text. Always confirm this information by clicking on the below link for the most accurate information: http://info.nsf.org/Certified/PwsComponents/Listings.asp?Company=3X440&Standard=061&



NSF/ANSI 61
Drinking Water System Components - Health Effects

NOTE: Unless otherwise indicated for Materials, Certification is only for the Water Contact Material shown in the Listing. Click here for a list of Abbreviations used in these Listings.


 
Ebara International Corporation 
1651 Cedar Line Drive
Rock Hill, SC 29730 
United States 
803-327-5005
Visit this company's website

Facility : Sparks, NV

Mechanical Devices

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Pumps[1] [G]
2CDU(A)(B)6(C)(D)(E)[2] 1¼" x 1" - 1½" x 1" CLD 23 MLTPL
3U(A)(B)(C)(D)(E)(F)(I)-XX[3] [4] [5] 2" x 1¼" - 3" x 2½" CLD 23 MLTPL
3U4(A)(B)(C)(D)(E)(F)(I)-XX[3] [4] [5] 2 1/4" x 1 1/2" CLD 23 MLTPL
CDU(A)(B)(C)(D)(E)(F)[6] 1¼" x 1" - 1½" x 1" CLD 23 MLTPL
JEU(A)(B)(C)(D)(E)[7] 1 1/4" x 1" CLD 23 MLTPL

[1] Sizes are expressed as suction x discharge.
[2] 2CDU Models:
    A - Casing Size/Impeller Size
        70/206
        70/306
        120/306
        200/506
    B - Motor horsepower (hp)
        20 - 2
        30 - 3
        50 - 5
    C - Motor Enclosure
        T - TEFC (Totally enclosed fan cooled)
        D - ODP (Open drip proof) 
    D - Phase/Volt
        3 - Three phase, 230/460 volt
        1 - Single phase, 115/230 volt
    E - Seal type
        C - Carbon/Ceramic/Viton
        G - Carbon/Ceramic/NBR
[3] 3U and 3U4 Models:
    A - Speed
        None - 3450 RPM
        4 - 1725 RPM
    B - Discharge size
        32 - 1 1/4"
        40 - 1 1/2"
        50 - 2"
        65 - 2 1/2" 
    C - Impeller performance code
        125
        160
        200
    "A" and "B" in the model name designate a different design in the impeller.
    D - Motor horsepower (hp)
        30  - 3
        50  - 5
        75  - 7.5
        100 - 10
        150 - 15
        200 - 20
        250 - 25
        300 - 30
    E - Motor Enclosure
        D - ODP (Open drip proof)
        T - TEFC (Totally enclosed fan cooled)
    F - Phase
        1 - Single phase
        3 - Three phase
    I - Mechanical Seal Type
        C - Carbon/Ceramic/Viton
        G - Carbon/Ceramic/NBR
[4] 3U model Certification does not include flange gaskets.
[5] XX - Special configuration (any 2 digit alpha numeric)
[6] CDU Models:
    A - Nominal motor speed
        Blank - 3600 rpm
        4     - 1750 rpm
    B - Casing Size/Impeller Size
        70/1
        70/3
        70/5
        120/1
        120/3
        120/5
        200/1
        200/3
        200/5
    C - Motor horsepower (hp)
        7  - 0.75
        10 - 1
        15 - 1.5
        20 - 2
        30 - 3
    D - Motor Enclosure
        D - ODP (Open drip proof)
        T - TEFC (Totally enclosed fan cooled)
    E - Motor Phase
        1 - Single phase
        3 - Three phase
    F - Mechanical Seal Type
        C - Carbon/Ceramic/Viton
        G - Carbon/Ceramic/NBR
[7] JEU Models:
    A - Housing and Impeller Number
        806
        1506
    B - Motor horsepower (hp)
        7 - 3/4
        10 - 1
        15 - 1/2
        20- 2
    C - Motor Enclosure
        D - ODP (Open drip proof)
        T - TEFC (Totally enclosed fan cooled)
    D - Phase
        1 - Single phase
        3 - Three phase
    E - Seal type
        C - Carbon/Ceramic/Viton
        G - Carbon/Ceramic/NBR
[G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for
    “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state
    laws and the U.S. Safe Drinking Water Act.

    

NOTE: Only products bearing the NSF Mark on the product, product packaging, and/or
      documentation shipped with the product are Certified.

Facility : Rock Hill, SC

Mechanical Devices

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Pumps[1] [G]
2CDU(A)(B)6(C)(D)(E)[2] 1 1/4"x1"-1 1/2"x1" CLD 23 MLTPL
3U(A)(B)(C)(D)(E)(F)(I)-XX[3] [4] [5] 2"x1 1/4"-3"x2 1/2" CLD 23 MLTPL
3U4(A)(B)(C)(D)(E)(F)(I)-XX[3] [4] [5] 2 1/4" x 1 1/2" CLD 23 MLTPL
CDU(A)(B)(C)(D)(E)(F)[6] 1 1/4"x1"-1 1/2"x1" CLD 23 MLTPL
JEU(A)(B)(C)(D)(E)[7] 1 1/4" x 1" CLD 23 MLTPL

[1] Size is expressed as suction x discharge.
[2] 2CDU Models 
    A - Casing Size/Impeller Size 
        70/206 
        70/306 
        120/306 
        200/506 
    B - Motor horsepower (hp) 
        20 - 2 
        30 - 3 
        50 - 5 
    C - Motor Enclosure 
        D - ODP (Open drip proof)
        T - TEFC (Totally enclosed fan cooled)  
    D - Phase/Volt 
        1 - Single phase, 115/230 volt 
        3 - Three phase, 230/460 volt 
    E - Seal type 
        C - Carbon/Ceramic/Viton 
        G - Carbon/Ceramic/NBR
[3] 3U and 3U4 Models
    A - Speed 
        None - 3450 RPM 
        4    - 1725 RPM 
    B - Discharge size 
        32 - 1 1/4" 
        40 - 1 1/2" 
        50 - 2"
        65 - 2 1/2" 
    C - Impeller performance code 
        125 
        160 
        200 
    "A" and "B" in the model name designate a different design in the impeller.
    D - Motor horsepower (hp) 
        30 - 3 
        50 - 5 
        75 - 7.5 
        100- 10 
        150 - 15 
        200 - 20 
        250 - 25 
        300 - 30 
    E - Motor enclosure 
        D - ODP (Open drip proof) 
        T - TEFC (Totally enclosed fan cooled) 
    F - Phase 
        1 - Single phase 
        3 - Three phase 
    I - Mechanical Seal Type 
        C - Carbon/Ceramic/Viton 
        G - Carbon/Ceramic/NBR
    4 models indicate a 4 pole motor as opposed to the standard 2 pole motor.
[4] 3U model Certification does not include flange gaskets.
[5] XX - Special configuration (any 2 digit alpha numeric)
[6] CDU Models 
    a - Nominal motor speed 
        Blank - 3600 rpm 
        4     - 1750 rpm 
    B - Casing size/impeller size 
        70/1 
        70/3 
        70/5 
        120/1 
        120/3 
        120/5 
        200/1
        200/3 
        200/5 
    C - Motor horsepower (hp) 
        7  - 0.75 
        10 - 1 
        15 - 1.5 
        20 - 2 
        30 - 3 
    D - Motor enclosure 
        D - ODP (Open drip proof) 
        T - TEFC (Totally enclosed fan cooled) 
    E - Motor phase   
        1 - single phase 
        3 - three phase 
    F - Mechanical seal type 
        C - Carbon/Ceramic/Viton 
        G - Carbon/Ceramic/NBR
[7] JEU Models
    A - Housing and impeller number 
        806 
        1506 
    B - Motor horsepower (hp) 
        7 - 3/4 
        10 - 1 
        15 - 1/2 
        20- 2 
    C - Motor enclosure 
        D - ODP (Open drip proof) 
        T - TEFC (Totally enclosed fan cooled) 
    D - Phase 
        1 - Single phase 
        3 - Three phase 
    E - Seal type 
        C - Carbon/Ceramic/Viton 
        G - Carbon/Ceramic/NBR
[G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for
    “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state
    laws and the U.S. Safe Drinking Water Act.

    

NOTE: Only products bearing the NSF Mark on the product, product packaging, and/or
      documentation shipped with the product are Certified.

Facility : Brendola (VI), Italy

Mechanical Devices

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Pumps[1] [G]
EVMU32-(W)F (X)(Y)(Z) S[2] 2 1/2" x 2 1/2" CLD 23 MLTPL
EVMU45-(W)F (X)(Y)(Z) S[2] 3" x 3" CLD 23 MLTPL
EVMU64-(W)F (X)(Y)(Z) S[2] 4" x 4" CLD 23 MLTPL
EVMUG32-(W)(R) F (X)(Y)(Z) S[3] 2 1/2" x 2 1/2" CLD 23 MLTPL
EVMUG45-(W)(R) F (X)(Y)(Z) S[3] 3" x 3" CLD 23 MLTPL
EVMUG64-(W)(R) F (X)(Y)(Z) S[3] 4" x 4" CLD 23 MLTPL
EVMUL32-(W)(R) F (X)(Y)(Z) S[2] 2 1/2" x 2 1/2" CLD 23 MLTPL
EVMUL45-(W)(R) F (X)(Y)(Z) S[2] 3" x 3" CLD 23 MLTPL
EVMUL64-(W)(R) F (X)(Y)(Z) S[2] 4" x 4" CLD 23 MLTPL

[1] Size is expressed as suction end x discharge end.
[2] W - Number of impellers 
        1-18 
    R - Number of reduced diameter impellers (32, 45, and 64 models only) 
        0-18 
    X - Horsepower of motor 
        0050 - 1/2HP 
        0075 - 3/4HP 
        0100 - 1.0HP 
        0150 - 1.5HP 
        0200 - 2.0 HP
        0300 - 3.0 HP 
        0500 - 5.0 HP 
        0750 - 7.5 HP 
        1000 - 10 HP 
        1500 - 15 HP 
        2000 - 20 HP 
        2500 - 25 HP 
        3000 - 30 HP 
        4000 - 40 HP 
        5000 - 50 HP 
    Y - Motor type 
        D - Open drip proof (ODP) 
        T - Totally enclosed fan cooled (TEFC) 
    Z - Motor phase 
        1 - Single phase 
        3 - Three phase
    "A" in the model name indicates sub-component design modifications.
[3] Size is expressed as suction end x discharge end.
    W - Number of impellers
        1-18
    R - Number of reduced diameter impellers
        0-18
    X - Horsepower of motor
        0050 - 1/2HP
        0075 - 3/4HP
        0100 - 1.0HP
        0150 - 1.5HP
        0200 - 2.0 HP
        0300 - 3.0 HP
        0500 - 5.0 HP
        0750 - 7.5 HP
        1000 - 10 HP
        1500 - 15 HP
        2000 - 20 HP
        2500 - 25 HP
        3000 - 30 HP
        4000 - 40 HP
        5000 - 50 HP
    Y - Motor type
        D - Open drip proof (ODP)
        T - Totally enclosed fan cooled (TEFC)
    Z - Motor phase
        1 - Single phase
        3 - Three phase
    "B" in the model name indicates sub-component design modifications.
[G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for
    “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state
    laws and the U.S. Safe Drinking Water Act.

    


Facility : Cles (TN), Italy

Mechanical Devices

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Pumps[1] [2] [G]
EVMU10-(W) F (X)(Y)(Z) S 2" x 2" CLD 23 MLTPL
EVMU18-(W) F (X)(Y)(Z) S 2" x 2" CLD 23 MLTPL
EVMU3-(W) F (X)(Y)(Z) S 1 1/4" x 1 1/4" CLD 23 MLTPL
EVMU5-(W) F (X)(Y)(Z) S 1 1/4" x 1 1/4" CLD 23 MLTPL
EVMUL10-(W) F (X)(Y)(Z) S 2" x 2" CLD 23 MLTPL
EVMUL18-(W) F (X)(Y)(Z) S 2" x 2" CLD 23 MLTPL
EVMUL3-(W) F (X)(Y)(Z) S 1 1/4" x 1 1/4" CLD 23 MLTPL
EVMUL5-(W) F (X)(Y)(Z) S 1 1/4" x 1 1/4" CLD 23 MLTPL

[1] Size is expressed as suction end x discharge end.
[2] W - Number of impellers 
        1 - 18  
    X - Horsepower of motor 
        0050 - 1/2 HP 
        0075 - 3/4 HP 
        0100 - 1.0 HP 
        0150 - 1.5 HP 
        0200 - 2.0 HP 
        0300 - 3.0 HP 
        0500 - 5.0 HP 
        0750 - 7.5 HP 
        1000 - 10 HP 
        1500 - 15 HP 
        2000 - 20 HP 
        2500 - 25 HP 
        3000 - 30 HP 
        4000 - 40 HP 
        5000 - 50 HP 
    Y - Motor Type 
        D - Open Drip Proof (ODP) 
        T - Totally Enclosed Fan Cooled (TEFC) 
    Z - Motor phase 
        1 - Single phase 
        3 - Three phase
    "A" in the model name indicates sub-component design modifications.
[G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for
    “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state
    laws and the U.S. Safe Drinking Water Act.

    


Number of matching Manufacturers is 1
Number of matching Products is 27
Processing time was 0 seconds