NSF Product and Service Listings

These NSF Official Listings are current as of Monday, December 10, 2018 at 12:15 a.m. Eastern Time. Please contact NSF to confirm the status of any Listing, report errors, or make suggestions.

Alert: NSF is concerned about fraudulent downloading and manipulation of website text. Always confirm this information by clicking on the below link for the most accurate information: http://info.nsf.org/Certified/PwsComponents/Listings.asp?Company=82480&Standard=061&


NSF/ANSI 61
Drinking Water System Components - Health Effects

NOTE: Unless otherwise indicated for Materials, Certification is only for the Water Contact Material shown in the Listing. Click here for a list of Abbreviations used in these Listings. Click here for the definitions of Water Contact Temperatures denoted in these Listings.

 
Sprayroq, Inc. 
4766 Grantswood Road
Suite 150 
Irondale, AL 35210 
United States 
800-634-0504 
205-957-0020


Facility : Irondale, AL

Protective (Barrier) Materials

    Water Water
  Water Contact Contact Contact
Trade Designation Size Restriction Temp Material

Coatings - Fittings
SprayShield Green 1[1] >= 30" CLD 23 PUR
SprayWall®[2] >= 6" CLD 23 PUR 

[1] Colors: Light Green
    Number of coats: 1-3
    Maximum field use dry film thickness (in mils): maximum 80 mils/coat; not to exceed a
    total maximum DFT of 240 mils
    Maximum thinner: None
    Recoat cure time and temperature: 15 minutes at 72°F
    Final cure time and temperature: 72 hours at 72°F
    Special comments: Mix ratio of Part A to Part B is 1:1 by volume. Application is by
    plural component spray gun. Minimum thickness is 80 mils.
[2] Colors: Gold
    Number of coats; 1
    Maximum field use dry film thickness (in mils): 500
    Maximum thinner: None
    Final cure time and temperature: 72 hours at 72°F
    Special comments: Mix ratio of Part A to Part B is 0.65:1 by volume. Minimum thickness
    is 250 mils.

Coatings - Tank
SprayWall®[2] >= 1,500,000 gal CLD 23 PUR 

[2] Colors: Gold
    Number of coats; 1
    Maximum field use dry film thickness (in mils): 500
    Maximum thinner: None
    Final cure time and temperature: 72 hours at 72°F
    Special comments: Mix ratio of Part A to Part B is 0.65:1 by volume. Minimum thickness
    is 250 mils.

Coatings - Valve
SprayShield Green 1[1] >= 30" CLD 23 PUR
SprayWall®[2] >= 4" CLD 23 PUR 

[1] Colors: Light Green
    Number of coats: 1-3
    Maximum field use dry film thickness (in mils): maximum 80 mils/coat; not to exceed a
    total maximum DFT of 240 mils
    Maximum thinner: None
    Recoat cure time and temperature: 15 minutes at 72°F
    Final cure time and temperature: 72 hours at 72°F
    Special comments: Mix ratio of Part A to Part B is 1:1 by volume. Application is by
    plural component spray gun. Minimum thickness is 80 mils.
[2] Colors: Gold
    Number of coats; 1
    Maximum field use dry film thickness (in mils): 500
    Maximum thinner: None
    Final cure time and temperature: 72 hours at 72°F
    Special comments: Mix ratio of Part A to Part B is 0.65:1 by volume. Minimum thickness
    is 250 mils.

Number of matching Manufacturers is 1
Number of matching Products is 5
Processing time was 0 seconds