NSF Product and Service Listings

These NSF Official Listings are current as of Thursday, November 21, 2024 at 12:15 a.m. Eastern Time. Please contact NSF to confirm the status of any Listing, report errors, or make suggestions.

Alert: NSF is concerned about fraudulent downloading and manipulation of website text. Always confirm this information by clicking on the below link for the most accurate information: http://info.nsf.org/Certified/PwsComponents/Listings.asp?Company=C0099871&Standard=061&


NSF/ANSI/CAN 61
Drinking Water System Components - Health Effects

NOTE: Unless otherwise indicated for Materials, Certification is only for the Water Contact Material shown in the Listing. Click here for a list of Abbreviations used in these Listings. Click here for the definitions of Water Contact Temperatures denoted in these Listings. Products certified to NSF/ANSI/CAN 61 comply with the health effects criteria in NSF/ANSI/CAN 600.

 
National Pump Company 
7706 North 71st Avenue
Glendale, AZ 85303 
United States 
800-966-5240 
623-979-3560
Visit this company's website


Facility : Glendale, AZ

Mechanical Devices

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Pumps [G]
VTP-(v)-(w)(x)(y)-(z)[1] [2] [3] [4] [5] 6" - 30" CLD 23 MLTPL 

[1] Certified for a minimum daily flow of 40,300 liters per day.
[2] Naming convention:
    (v)-(w)(x)(y)-(z):
    v: Configuration (VS1, VS6, BA)
    w: Hydraulic Design (L, M, N, K, J, E, H)
    x: Size, In Inches (6-30)
    y: Impeller Model (LC, MC, HC, XHC, XXHC, LC-S, MC-S, HC-S, XHC-S, XXHC-S)
    z: Number of Stages
[3] Certification does not include the pump Motor/Driver.
[4] The following are sold as replacement parts: bowl assembly, gasket for top flange
    column, packing, mechanical seal o-ring, tension bearing, sleeve bearing, line keyed
    coupling, coupling key, coupling set screw, coupling retaining ring, shaft sleeve,
    sleeve set screw, open lineshaft bearing, enclosing tube bearing, bat bearing, throttle
    bearing, bearing o-ring, bowl wear ring, spring pin, bowl bearing, bow o-ring, impeller
    wear ring, thrust
    collar, screws for thrust collar, thrust collar key, and suction bearing.
[5] Configuration VS1 includes bowl assembly, discharge assembly, and optional column
    assembly.  Configuration VS6 
    includes the bowl assembly, discharge head assembly, suction barrel assembly, and
    optional column assembly.  
    Configuration BA includes the bowl assembly only.
[G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for
    “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state
    laws and the U.S. Safe Drinking Water Act.

Pumps - Submersible Pumps - Pump Ends [G]
STP-(v)-S(w)(x)(y)-(z)[1] [6] [7] [8] [9] 6" - 30" CLD 23 MLTPL 

[1] Certified for a minimum daily flow of 40,300 liters per day.
[6] Naming convention:
    (v)-S(w)(x)(y)-(z):
    v: Configuration (VS0, BA)
    w: Hydraulic Design (L, M, N, K, J, E, H)
    x: Size, In Inches (6-30)
    y: Impeller Model (LC, MC, HC, XHC, XXHC, LC-S, MC-S, HC-S, XHC-S, XXHC-S)
    z: Number of Stages
[7] Certification does not include the pump Motor/Driver and submersible pump cables.
[8] The following are sold as replacement parts: bowl assembly, bowl wear ring, spring pin,
    bowl bearing, impeller wear ring, impeller thrust collar, screws for thrust collar,
    impeller key, suction bearing u-thrust collar, screws for up-thrust collar, motor
    coupling, coupling key and coupling set screw.
[9] Configuration VS0 includes bowl assembly, discharge assembly and optional column
    assembly.  Configuration BA includes the bowl assembly only.
[G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for
    “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state
    laws and the U.S. Safe Drinking Water Act.

Number of matching Manufacturers is 1
Number of matching Products is 2
Processing time was 0 seconds