NSF Product and Service Listings

These NSF Official Listings are current as of Monday, August 17, 2026 at 12:15 a.m. Eastern Time. Please contact NSF to confirm the status of any Listing, report errors, or make suggestions.

Alert: NSF is concerned about fraudulent downloading and manipulation of website text. Always confirm this information by clicking on the below link for the most accurate information: http://info.nsf.org/Certified/PwsComponents/Listings.asp?Company=C0349945&Standard=061&


NSF/ANSI/CAN 61
Drinking Water System Components - Health Effects

NOTE: Unless otherwise indicated for Materials, Certification is only for the Water Contact Material shown in the Listing. Click here for a list of Abbreviations used in these Listings. Click here for the definitions of Water Contact Temperatures denoted in these Listings. Products certified to NSF/ANSI/CAN 61 comply with the health effects criteria in NSF/ANSI/CAN 600.

 
IFS Coatings Inc. 
3601 North Interstate 35
Gainesville, TX 76240 
United States 
940-668-1062


Facility : Ardmore, OK

Protective (Barrier) Materials

    Water Water
  Water Contact Contact Contact
Trade Designation Size Restriction Temp Material

Coatings - Fittings[1] [G]
PuroPlaz / PE207018-Gray-61/Beige-61 [2] CLD 23 ECPC
PuroPlaz / PE201033- Black-61 [2] CLD 23 ECPC
PuroPlaz / PE202015-Blue-61 [2] CLD 23 ECPC
PuroPlaz / PE203019-Green-61 [2] CLD 23 ECPC
PuroPlaz / PE205002-Yellow-61 [2] CLD 23 ECPC
PuroPlaz / PE206006-Red-61 [2] CLD 23 ECPC
PuroPlaz / PE208006-White-61 [2] CLD 23 ECPC
PuroPlaz / PE209012- Clear-61/or Special-61 [2] CLD 23 ECPC 

[1] Coating Notes: 
    Colors: Black, Blue, Green, Yellow, Red, Gray, Beige, White, Clear, Special
    Number Of Coats: 1-2
    Maximum Field Use Dry Thickness (in mils): 40 mils (20 mils per coat)
    Recoat Cure Time and Temperature: 2-8 minutes at 380-425°F
    Final Cure Time/Temperature: 2-7 minutes at 380-425°F
    Special Comments: Spray application: Pre-heat steel substrate for 30 min at 482°F, and 
                      spray PuroPlaz PE20 on the substrate before the substrate temperatures
    
                      decrease below 302°F. The pre-heat temperature may need to be adjusted
    
                      for substrate thickness. Post heat at 400F to 482F until coating is 
                      smooth. 
                      Fluidized Bed application: Preheat steel substrate for 30 min at
    482°F, 
                      dip in a fluidized bed PuroPlaz PE20 for 5-10 seconds until desired 
                      coating thickness is achieved. Pre-heat temperatures may need to be 
                      adjusted depending on substrate thickness. Post heat at 400F to 482F 
                      until coating is smooth. Recoat cure time and temperature: Pre-heat 
                      metal substrate to 380°F to 425°F. Apply coating and post heat at 400F
    
                      - 425°F for 2-7 minutes until coating is smooth.
[2] Certified for the following end uses: 
    Tanks 3 gallons and greater 
    Pipes, fittings, valves, meters, and pumps 1" and greater 
[G] Product is Certified to NSF/ANSI/CAN 372 and conforms with the lead content requirements
    for "lead free" plumbing as defined by California, Vermont, Maryland, and Louisiana
    state laws and the U.S. Safe Drinking Water Act.

Coatings - Mechanical Devices[1] [G]
PuroPlaz / PE207018-Gray-61/Beige-61 [2] CLD 23 ECPC
PuroPlaz / PE201033- Black-61 [2] CLD 23 ECPC
PuroPlaz / PE202015-Blue-61 [2] CLD 23 ECPC
PuroPlaz / PE203019-Green-61 [2] CLD 23 ECPC
PuroPlaz / PE205002-Yellow-61 [2] CLD 23 ECPC
PuroPlaz / PE206006-Red-61 [2] CLD 23 ECPC
PuroPlaz / PE208006-White-61 [2] CLD 23 ECPC
PuroPlaz / PE209012- Clear-61/or Special-61 [2] CLD 23 ECPC 

[1] Coating Notes: 
    Colors: Black, Blue, Green, Yellow, Red, Gray, Beige, White, Clear, Special
    Number Of Coats: 1-2
    Maximum Field Use Dry Thickness (in mils): 40 mils (20 mils per coat)
    Recoat Cure Time and Temperature: 2-8 minutes at 380-425°F
    Final Cure Time/Temperature: 2-7 minutes at 380-425°F
    Special Comments: Spray application: Pre-heat steel substrate for 30 min at 482°F, and 
                      spray PuroPlaz PE20 on the substrate before the substrate temperatures
    
                      decrease below 302°F. The pre-heat temperature may need to be adjusted
    
                      for substrate thickness. Post heat at 400F to 482F until coating is 
                      smooth. 
                      Fluidized Bed application: Preheat steel substrate for 30 min at
    482°F, 
                      dip in a fluidized bed PuroPlaz PE20 for 5-10 seconds until desired 
                      coating thickness is achieved. Pre-heat temperatures may need to be 
                      adjusted depending on substrate thickness. Post heat at 400F to 482F 
                      until coating is smooth. Recoat cure time and temperature: Pre-heat 
                      metal substrate to 380°F to 425°F. Apply coating and post heat at 400F
    
                      - 425°F for 2-7 minutes until coating is smooth.
[2] Certified for the following end uses: 
    Tanks 3 gallons and greater 
    Pipes, fittings, valves, meters, and pumps 1" and greater 
[G] Product is Certified to NSF/ANSI/CAN 372 and conforms with the lead content requirements
    for "lead free" plumbing as defined by California, Vermont, Maryland, and Louisiana
    state laws and the U.S. Safe Drinking Water Act.

Coatings - Pipe[1] [G]
PuroPlaz / PE207018-Gray-61/Beige-61 [2] CLD 23 ECPC
PuroPlaz / PE201033- Black-61 [2] CLD 23 ECPC
PuroPlaz / PE202015-Blue-61 [2] CLD 23 ECPC
PuroPlaz / PE203019-Green-61 [2] CLD 23 ECPC
PuroPlaz / PE205002-Yellow-61 [2] CLD 23 ECPC
PuroPlaz / PE206006-Red-61 [2] CLD 23 ECPC
PuroPlaz / PE208006-White-61 [2] CLD 23 ECPC
PuroPlaz / PE209012- Clear-61/or Special-61 [2] CLD 23 ECPC 

[1] Coating Notes: 
    Colors: Black, Blue, Green, Yellow, Red, Gray, Beige, White, Clear, Special
    Number Of Coats: 1-2
    Maximum Field Use Dry Thickness (in mils): 40 mils (20 mils per coat)
    Recoat Cure Time and Temperature: 2-8 minutes at 380-425°F
    Final Cure Time/Temperature: 2-7 minutes at 380-425°F
    Special Comments: Spray application: Pre-heat steel substrate for 30 min at 482°F, and 
                      spray PuroPlaz PE20 on the substrate before the substrate temperatures
    
                      decrease below 302°F. The pre-heat temperature may need to be adjusted
    
                      for substrate thickness. Post heat at 400F to 482F until coating is 
                      smooth. 
                      Fluidized Bed application: Preheat steel substrate for 30 min at
    482°F, 
                      dip in a fluidized bed PuroPlaz PE20 for 5-10 seconds until desired 
                      coating thickness is achieved. Pre-heat temperatures may need to be 
                      adjusted depending on substrate thickness. Post heat at 400F to 482F 
                      until coating is smooth. Recoat cure time and temperature: Pre-heat 
                      metal substrate to 380°F to 425°F. Apply coating and post heat at 400F
    
                      - 425°F for 2-7 minutes until coating is smooth.
[2] Certified for the following end uses: 
    Tanks 3 gallons and greater 
    Pipes, fittings, valves, meters, and pumps 1" and greater 
[G] Product is Certified to NSF/ANSI/CAN 372 and conforms with the lead content requirements
    for "lead free" plumbing as defined by California, Vermont, Maryland, and Louisiana
    state laws and the U.S. Safe Drinking Water Act.

Coatings - Pump[1] [G]
PuroPlaz / PE207018-Gray-61/Beige-61 [2] CLD 23 ECPC
PuroPlaz / PE201033- Black-61 [2] CLD 23 ECPC
PuroPlaz / PE202015-Blue-61 [2] CLD 23 ECPC
PuroPlaz / PE203019-Green-61 [2] CLD 23 ECPC
PuroPlaz / PE205002-Yellow-61 [2] CLD 23 ECPC
PuroPlaz / PE206006-Red-61 [2] CLD 23 ECPC
PuroPlaz / PE208006-White-61 [2] CLD 23 ECPC
PuroPlaz / PE209012- Clear-61/or Special-61 [2] CLD 23 ECPC 

[1] Coating Notes: 
    Colors: Black, Blue, Green, Yellow, Red, Gray, Beige, White, Clear, Special
    Number Of Coats: 1-2
    Maximum Field Use Dry Thickness (in mils): 40 mils (20 mils per coat)
    Recoat Cure Time and Temperature: 2-8 minutes at 380-425°F
    Final Cure Time/Temperature: 2-7 minutes at 380-425°F
    Special Comments: Spray application: Pre-heat steel substrate for 30 min at 482°F, and 
                      spray PuroPlaz PE20 on the substrate before the substrate temperatures
    
                      decrease below 302°F. The pre-heat temperature may need to be adjusted
    
                      for substrate thickness. Post heat at 400F to 482F until coating is 
                      smooth. 
                      Fluidized Bed application: Preheat steel substrate for 30 min at
    482°F, 
                      dip in a fluidized bed PuroPlaz PE20 for 5-10 seconds until desired 
                      coating thickness is achieved. Pre-heat temperatures may need to be 
                      adjusted depending on substrate thickness. Post heat at 400F to 482F 
                      until coating is smooth. Recoat cure time and temperature: Pre-heat 
                      metal substrate to 380°F to 425°F. Apply coating and post heat at 400F
    
                      - 425°F for 2-7 minutes until coating is smooth.
[2] Certified for the following end uses: 
    Tanks 3 gallons and greater 
    Pipes, fittings, valves, meters, and pumps 1" and greater 
[G] Product is Certified to NSF/ANSI/CAN 372 and conforms with the lead content requirements
    for "lead free" plumbing as defined by California, Vermont, Maryland, and Louisiana
    state laws and the U.S. Safe Drinking Water Act.

Coatings - Tank[1] [G]
PuroPlaz / PE207018-Gray-61/Beige-61 [2] CLD 23 ECPC
PuroPlaz / PE201033- Black-61 [2] CLD 23 ECPC
PuroPlaz / PE202015-Blue-61 [2] CLD 23 ECPC
PuroPlaz / PE203019-Green-61 [2] CLD 23 ECPC
PuroPlaz / PE205002-Yellow-61 [2] CLD 23 ECPC
PuroPlaz / PE206006-Red-61 [2] CLD 23 ECPC
PuroPlaz / PE208006-White-61 [2] CLD 23 ECPC
PuroPlaz / PE209012- Clear-61/or Special-61 [2] CLD 23 ECPC 

[1] Coating Notes: 
    Colors: Black, Blue, Green, Yellow, Red, Gray, Beige, White, Clear, Special
    Number Of Coats: 1-2
    Maximum Field Use Dry Thickness (in mils): 40 mils (20 mils per coat)
    Recoat Cure Time and Temperature: 2-8 minutes at 380-425°F
    Final Cure Time/Temperature: 2-7 minutes at 380-425°F
    Special Comments: Spray application: Pre-heat steel substrate for 30 min at 482°F, and 
                      spray PuroPlaz PE20 on the substrate before the substrate temperatures
    
                      decrease below 302°F. The pre-heat temperature may need to be adjusted
    
                      for substrate thickness. Post heat at 400F to 482F until coating is 
                      smooth. 
                      Fluidized Bed application: Preheat steel substrate for 30 min at
    482°F, 
                      dip in a fluidized bed PuroPlaz PE20 for 5-10 seconds until desired 
                      coating thickness is achieved. Pre-heat temperatures may need to be 
                      adjusted depending on substrate thickness. Post heat at 400F to 482F 
                      until coating is smooth. Recoat cure time and temperature: Pre-heat 
                      metal substrate to 380°F to 425°F. Apply coating and post heat at 400F
    
                      - 425°F for 2-7 minutes until coating is smooth.
[2] Certified for the following end uses: 
    Tanks 3 gallons and greater 
    Pipes, fittings, valves, meters, and pumps 1" and greater 
[G] Product is Certified to NSF/ANSI/CAN 372 and conforms with the lead content requirements
    for "lead free" plumbing as defined by California, Vermont, Maryland, and Louisiana
    state laws and the U.S. Safe Drinking Water Act.

Coatings - Valve[1] [G]
PuroPlaz / PE207018-Gray-61/Beige-61 [2] CLD 23 ECPC
PuroPlaz / PE201033- Black-61 [2] CLD 23 ECPC
PuroPlaz / PE202015-Blue-61 [2] CLD 23 ECPC
PuroPlaz / PE203019-Green-61 [2] CLD 23 ECPC
PuroPlaz / PE205002-Yellow-61 [2] CLD 23 ECPC
PuroPlaz / PE206006-Red-61 [2] CLD 23 ECPC
PuroPlaz / PE208006-White-61 [2] CLD 23 ECPC
PuroPlaz / PE209012- Clear-61/or Special-61 [2] CLD 23 ECPC 

[1] Coating Notes: 
    Colors: Black, Blue, Green, Yellow, Red, Gray, Beige, White, Clear, Special
    Number Of Coats: 1-2
    Maximum Field Use Dry Thickness (in mils): 40 mils (20 mils per coat)
    Recoat Cure Time and Temperature: 2-8 minutes at 380-425°F
    Final Cure Time/Temperature: 2-7 minutes at 380-425°F
    Special Comments: Spray application: Pre-heat steel substrate for 30 min at 482°F, and 
                      spray PuroPlaz PE20 on the substrate before the substrate temperatures
    
                      decrease below 302°F. The pre-heat temperature may need to be adjusted
    
                      for substrate thickness. Post heat at 400F to 482F until coating is 
                      smooth. 
                      Fluidized Bed application: Preheat steel substrate for 30 min at
    482°F, 
                      dip in a fluidized bed PuroPlaz PE20 for 5-10 seconds until desired 
                      coating thickness is achieved. Pre-heat temperatures may need to be 
                      adjusted depending on substrate thickness. Post heat at 400F to 482F 
                      until coating is smooth. Recoat cure time and temperature: Pre-heat 
                      metal substrate to 380°F to 425°F. Apply coating and post heat at 400F
    
                      - 425°F for 2-7 minutes until coating is smooth.
[2] Certified for the following end uses: 
    Tanks 3 gallons and greater 
    Pipes, fittings, valves, meters, and pumps 1" and greater 
[G] Product is Certified to NSF/ANSI/CAN 372 and conforms with the lead content requirements
    for "lead free" plumbing as defined by California, Vermont, Maryland, and Louisiana
    state laws and the U.S. Safe Drinking Water Act.



Facility : Gainesville, TX

Protective (Barrier) Materials

    Water Water
  Water Contact Contact Contact
Trade Designation Size Restriction Temp Material

Coatings - Fittings [G]
Black (ERSS11685) [1] >=1" C. HOT PEC
Blue (ERSS22597) [2] >=1" C. HOT PEC
Brown (ERSS47676) [3] >=1" C. HOT PEC
Gray (ERSS75636) [2] >=1" C. HOT PEC
Green (ERSS33254) [2] >=1" C. HOT PEC
Red (ERSS62900) [2] >=1" C. HOT PEC
White (ERSS83401) [2] >=1" C. HOT PEC
Yellow (ERSS51039) [2] >=1" C. HOT PEC 

[1] Colors: Black
    Number of coats: 1
    Maximum field use dry film thickness (in mils): 60 mils
    Final cure time and temperature: 10 minutes at 400°F
    Special Comments: Pre-heat part to 400°F-475°F before powder application (depending on
    thickness of the substrate and application)
[2] Colors: Blue, Gray, Green, Red, White, Yellow
    Number of coats: 1
    Maximum field use dry film thickness (in mils): 20 mils
    Final cure time and temperature: 10 minutes at 400°F
    Special Comments: Pre-heat part to 400°F-475°F before powder application (depending on
    thickness of the substrate and application)
[3] Colors: Brown
    Number of coats: 1
    Maximum field use dry film thickness (in mils): 20 mils
    Final cure time and temperature: 15 minutes at 400°F
    Special Comments: Pre-heat part to 400°F-475°F before powder application (depending on
    thickness of the substrate and application
[G] Product is Certified to NSF/ANSI/CAN 372 and conforms with the lead content requirements
    for "lead free" plumbing as defined by California, Vermont, Maryland, and Louisiana
    state laws and the U.S. Safe Drinking Water Act.

Coatings - Pipe [G]
Black (ERSS11685) [1] >=1" C. HOT PEC
Blue (ERSS22597)[2] >=1" C. HOT PEC
Brown (ERSS47676) [3] >=1" C. HOT PEC
Gray (ERSS75636) [2] >=1" C. HOT PEC
Green (ERSS33254) [2] >=1" C. HOT PEC
Red (ERSS62900) [2] >=1" C. HOT PEC
White (ERSS83401) [2] >=1" C. HOT PEC
Yellow (ERSS51039) [2] >=1" C. HOT PEC 

[1] Colors: Black
    Number of coats: 1
    Maximum field use dry film thickness (in mils): 60 mils
    Final cure time and temperature: 10 minutes at 400°F
    Special Comments: Pre-heat part to 400°F-475°F before powder application (depending on
    thickness of the substrate and application)
[2] Colors: Blue, Gray, Green, Red, White, Yellow
    Number of coats: 1
    Maximum field use dry film thickness (in mils): 20 mils
    Final cure time and temperature: 10 minutes at 400°F
    Special Comments: Pre-heat part to 400°F-475°F before powder application (depending on
    thickness of the substrate and application)
[3] Colors: Brown
    Number of coats: 1
    Maximum field use dry film thickness (in mils): 20 mils
    Final cure time and temperature: 15 minutes at 400°F
    Special Comments: Pre-heat part to 400°F-475°F before powder application (depending on
    thickness of the substrate and application
[G] Product is Certified to NSF/ANSI/CAN 372 and conforms with the lead content requirements
    for "lead free" plumbing as defined by California, Vermont, Maryland, and Louisiana
    state laws and the U.S. Safe Drinking Water Act.

Coatings - Pump [G]
Black (ERSS11685) [1] >=1" C. HOT PEC
Blue (ERSS22597) [2] >=1" C. HOT PEC
Brown (ERSS47676) [3] >=1" C. HOT PEC
Gray (ERSS75636) [2] >=1" C. HOT PEC
Green (ERSS33254) [2] >=1" C. HOT PEC
Red (ERSS62900) [2] >=1" C. HOT PEC
White (ERSS83401) [2] >=1" C. HOT PEC
Yellow (ERSS51039) [2] >=1" C. HOT PEC 

[1] Colors: Black
    Number of coats: 1
    Maximum field use dry film thickness (in mils): 60 mils
    Final cure time and temperature: 10 minutes at 400°F
    Special Comments: Pre-heat part to 400°F-475°F before powder application (depending on
    thickness of the substrate and application)
[2] Colors: Blue, Gray, Green, Red, White, Yellow
    Number of coats: 1
    Maximum field use dry film thickness (in mils): 20 mils
    Final cure time and temperature: 10 minutes at 400°F
    Special Comments: Pre-heat part to 400°F-475°F before powder application (depending on
    thickness of the substrate and application)
[3] Colors: Brown
    Number of coats: 1
    Maximum field use dry film thickness (in mils): 20 mils
    Final cure time and temperature: 15 minutes at 400°F
    Special Comments: Pre-heat part to 400°F-475°F before powder application (depending on
    thickness of the substrate and application
[G] Product is Certified to NSF/ANSI/CAN 372 and conforms with the lead content requirements
    for "lead free" plumbing as defined by California, Vermont, Maryland, and Louisiana
    state laws and the U.S. Safe Drinking Water Act.

Coatings - Tank [G]
Black (ERSS11685) [1] >=5  gal. C. HOT PEC
Blue (ERSS22597) [2] >=5  gal. C. HOT PEC
Brown (ERSS47676) [3] >=5  gal. C. HOT PEC
Gray (ERSS75636) [2] >=5  gal. C. HOT PEC
Green (ERSS33254) [2] >=5  gal. C. HOT PEC
Red (ERSS62900) [2] >=5  gal. C. HOT PEC
White (ERSS83401) [2] >=5  gal. C. HOT PEC
Yellow (ERSS51039) [2] >=5  gal. C. HOT PEC 

[1] Colors: Black
    Number of coats: 1
    Maximum field use dry film thickness (in mils): 60 mils
    Final cure time and temperature: 10 minutes at 400°F
    Special Comments: Pre-heat part to 400°F-475°F before powder application (depending on
    thickness of the substrate and application)
[2] Colors: Blue, Gray, Green, Red, White, Yellow
    Number of coats: 1
    Maximum field use dry film thickness (in mils): 20 mils
    Final cure time and temperature: 10 minutes at 400°F
    Special Comments: Pre-heat part to 400°F-475°F before powder application (depending on
    thickness of the substrate and application)
[3] Colors: Brown
    Number of coats: 1
    Maximum field use dry film thickness (in mils): 20 mils
    Final cure time and temperature: 15 minutes at 400°F
    Special Comments: Pre-heat part to 400°F-475°F before powder application (depending on
    thickness of the substrate and application
[G] Product is Certified to NSF/ANSI/CAN 372 and conforms with the lead content requirements
    for "lead free" plumbing as defined by California, Vermont, Maryland, and Louisiana
    state laws and the U.S. Safe Drinking Water Act.

Coatings - Valve [G]
Black (ERSS11685) [2] >=1" C. HOT PEC
Blue (ERSS22591) [2] >=1" C. HOT PEC
Brown (ERSS47676) [3] >=1" C. HOT PEC
Gray (ERSS75636) [2] >=1" C. HOT PEC
Green (ERSS33254) [2] >=1" C. HOT PEC
Red (ERSS62900) [2] >=1" C. HOT PEC
White (ERSS83401) [2] >=1" C. HOT PEC
Yellow (ERSS51039) [2] >=1" C. HOT PEC 

[2] Colors: Blue, Gray, Green, Red, White, Yellow
    Number of coats: 1
    Maximum field use dry film thickness (in mils): 20 mils
    Final cure time and temperature: 10 minutes at 400°F
    Special Comments: Pre-heat part to 400°F-475°F before powder application (depending on
    thickness of the substrate and application)
[3] Colors: Brown
    Number of coats: 1
    Maximum field use dry film thickness (in mils): 20 mils
    Final cure time and temperature: 15 minutes at 400°F
    Special Comments: Pre-heat part to 400°F-475°F before powder application (depending on
    thickness of the substrate and application
[G] Product is Certified to NSF/ANSI/CAN 372 and conforms with the lead content requirements
    for "lead free" plumbing as defined by California, Vermont, Maryland, and Louisiana
    state laws and the U.S. Safe Drinking Water Act.

Number of matching Manufacturers is 1
Number of matching Products is 88
Processing time was 0 seconds