NSF Product and Service Listings

[1] Colors: Dark Green
    Number of Coats: 1
    Maximum Field Use Dry Film Thickness (in mils): 50
    Maximum thinner: None
    Final Cure Time and Temperature: 6233W 4G: 30-45 seconds at 450°F; 6233W 8G: 60-90
    seconds at 450°F; 6233W 11G: 90-120 seconds at 450°F
    Special Comments: Preheat part to 425° - 488° F before application of powder.
[2] Number of Coats: 1
    Maximum Field Use Dry Film Thickness (in mils): 60
    Final Cure Time and Temperature: 206N: 10 minutes at 400°F; 206N Extra LG: 16 minutes at
    400°F; 206N Fluid Bed: 10 minutes at 400°F; 206N Long Gel: 10 minutes at 400°F
[4] Number of Coats: 1
    Sequence of Coats: N/A
    Maximum Field Use Dry Film Thickness (in mils): 60
    Maximum Thinner: None
    Final Cure Time and Temperature: 25 minutes at 425° F
[5] Certified for a maximum surface area to volume ratio of 122.1 sq. in./L for pump end use.

[1] Colors: Dark Green
    Number of Coats: 1
    Maximum Field Use Dry Film Thickness (in mils): 50
    Maximum thinner: None
    Final Cure Time and Temperature: 6233W 4G: 30-45 seconds at 450°F; 6233W 8G: 60-90
    seconds at 450°F; 6233W 11G: 90-120 seconds at 450°F
    Special Comments: Preheat part to 425° - 488° F before application of powder.
[2] Number of Coats: 1
    Maximum Field Use Dry Film Thickness (in mils): 60
    Final Cure Time and Temperature: 206N: 10 minutes at 400°F; 206N Extra LG: 16 minutes at
    400°F; 206N Fluid Bed: 10 minutes at 400°F; 206N Long Gel: 10 minutes at 400°F
[4] Number of Coats: 1
    Sequence of Coats: N/A
    Maximum Field Use Dry Film Thickness (in mils): 60
    Maximum Thinner: None
    Final Cure Time and Temperature: 25 minutes at 425° F
[5] Certified for a maximum surface area to volume ratio of 122.1 sq. in./L for pump end use.

[2] Number of Coats: 1
    Maximum Field Use Dry Film Thickness (in mils): 60
    Final Cure Time and Temperature: 206N: 10 minutes at 400°F; 206N Extra LG: 16 minutes at
    400°F; 206N Fluid Bed: 10 minutes at 400°F; 206N Long Gel: 10 minutes at 400°F
[3] Certified for a maximum surface area to volume ratio of 122.1 sq. in./L. for pump end
    use.
[4] Number of Coats: 1
    Sequence of Coats: N/A
    Maximum Field Use Dry Film Thickness (in mils): 60
    Maximum Thinner: None
    Final Cure Time and Temperature: 25 minutes at 425° F
[5] Certified for a maximum surface area to volume ratio of 122.1 sq. in./L for pump end use.

[2] Number of Coats: 1
    Maximum Field Use Dry Film Thickness (in mils): 60
    Final Cure Time and Temperature: 206N: 10 minutes at 400°F; 206N Extra LG: 16 minutes at
    400°F; 206N Fluid Bed: 10 minutes at 400°F; 206N Long Gel: 10 minutes at 400°F
[4] Number of Coats: 1
    Sequence of Coats: N/A
    Maximum Field Use Dry Film Thickness (in mils): 60
    Maximum Thinner: None
    Final Cure Time and Temperature: 25 minutes at 425° F

[1] Colors: Dark Green
    Number of Coats: 1
    Maximum Field Use Dry Film Thickness (in mils): 50
    Maximum thinner: None
    Final Cure Time and Temperature: 6233W 4G: 30-45 seconds at 450°F; 6233W 8G: 60-90
    seconds at 450°F; 6233W 11G: 90-120 seconds at 450°F
    Special Comments: Preheat part to 425° - 488° F before application of powder.
[2] Number of Coats: 1
    Maximum Field Use Dry Film Thickness (in mils): 60
    Final Cure Time and Temperature: 206N: 10 minutes at 400°F; 206N Extra LG: 16 minutes at
    400°F; 206N Fluid Bed: 10 minutes at 400°F; 206N Long Gel: 10 minutes at 400°F
[4] Number of Coats: 1
    Sequence of Coats: N/A
    Maximum Field Use Dry Film Thickness (in mils): 60
    Maximum Thinner: None
    Final Cure Time and Temperature: 25 minutes at 425° F
[5] Certified for a maximum surface area to volume ratio of 122.1 sq. in./L for pump end use.

[1] Certified for use in municipal wells in conjunction with a submersible pump or a line
    shaft pump. Not Certified for residential use.
[G] Product is Certified to NSF/ANSI/CAN 372 and conforms with the lead content requirements
    for "lead free" plumbing as defined by California, Vermont, Maryland, and Louisiana
    state laws and the U.S. Safe Drinking Water Act.

[1] Certified for a maximum surface area to volume ratio of 2.0 square inches/L.
[2] This product has also been evaluated for use in Mechanical Plumbing Device applications
    with a maximum use restriction of 0.8 square inches/L.

[1] Certified for a maximum surface area to volume ratio of 2.0 square inches/L.
[2] This product has also been evaluated for use in Mechanical Plumbing Device applications
    with a maximum use restriction of 0.8 square inches/L.

[1] Product also complies with NSF/ANSI 372.
[G] Product is Certified to NSF/ANSI/CAN 372 and conforms with the lead content requirements
    for "lead free" plumbing as defined by California, Vermont, Maryland, and Louisiana
    state laws and the U.S. Safe Drinking Water Act.

[1] Product also complies with NSF/ANSI 372.
[2] Suffixes:
    blank 
    B   - Buried 
    EX  - Base extension 
    MP  - Mounted pump 
    P   - Pipe mounted 
    PST - Pump system tank
    S
[G] Product is Certified to NSF/ANSI/CAN 372 and conforms with the lead content requirements
    for "lead free" plumbing as defined by California, Vermont, Maryland, and Louisiana
    state laws and the U.S. Safe Drinking Water Act.

[1] Only products bearing the NSF Mark on the product, product packaging, and/or
    documentation shipped with the product are Certified.
[2] Certified for mechanical seals for use with pump shafts ranging from 1" - 12" in
    diameter.  Certified for equivalent metric sizes.
[3] Certified for use as a packing material in pumps with shaft diameters >= 0.625".
[4] Certified for mechanical seals for use with pump shafts ranging from 16-110 mm in
    diameter.
[5] Certified for mechanical seals for use with pump shafts ranging from 1"-8" in diameter.
    Certified
    for equivalent metric sizes.
[G] Product is Certified to NSF/ANSI/CAN 372 and conforms with the lead content requirements
    for "lead free" plumbing as defined by California, Vermont, Maryland, and Louisiana
    state laws and the U.S. Safe Drinking Water Act.

[1] Colors: Blue, White
    Number of coats: 3
    Maximum field use dry film thickness (in mils): 45 (15 mils/coat)
    Recoat cure time and temperature: 6 hours at 77°F
    Final cure time and temperature: 7 days at 77°F
    Special Comments: Mix ratio of Part A:B is 2:1 by volume

[1] Colors: Blue, White
    Number of coats: 3
    Maximum field use dry film thickness (in mils): 45 (15 mils/coat)
    Recoat cure time and temperature: 6 hours at 77°F
    Final cure time and temperature: 7 days at 77°F
    Special Comments: Mix ratio of Part A:B is 2:1 by volume

[1] Colors: Blue, White
    Number of coats: 3
    Maximum field use dry film thickness (in mils): 45 (15 mils/coat)
    Recoat cure time and temperature: 6 hours at 77°F
    Final cure time and temperature: 7 days at 77°F
    Special Comments: Mix ratio of Part A:B is 2:1 by volume

[1] Colors: Blue, White
    Number of coats: 3
    Maximum field use dry film thickness (in mils): 45 (15 mils/coat)
    Recoat cure time and temperature: 6 hours at 77°F
    Final cure time and temperature: 7 days at 77°F
    Special Comments: Mix ratio of Part A:B is 2:1 by volume

[1] Colors: Blue, White
    Number of coats: 3
    Maximum field use dry film thickness (in mils): 45 (15 mils/coat)
    Recoat cure time and temperature: 6 hours at 77°F
    Final cure time and temperature: 7 days at 77°F
    Special Comments: Mix ratio of Part A:B is 2:1 by volume

[1] Size is expressed as Diameter x length.
[2] BW-8040 and ULP-8040 models are Certified for a minimum daily flow of 10000 gallons.
    BW-4040 model is Certified for a minimum daily flow of 2400 gallons.
    ULP-4040 model is Certified for a minimum daily flow of 2600 gallons.
    ULP-4040MR model is Certified for a minimum daily flow of 2200 gallons.
    ULP-4040HR model is Certified for a minimum daily flow of 1800 gallons.
    ULP-4021 model is Certified for a minimum daily flow of 950 gallons.
[3] Models require the following flushing procedure:
    BW-4040, ULP-4040, ULP-4040MR, ULP-4040HR and ULP-4021 require a 4 gpm flush for 24
    hours using tap water.
    BW-8040 and ULP-8040 require a 15 gpm flush for 24 hours using tap water.

[1] Certified for a maximum surface area to volume ratio of 0.8 sq. in./L when used at Cold
    (23°C) temperature.

[1] Certified for a maximum surface area to volume ratio of 0.3 sq. in./L when used at
    Commercial Hot (82°C) temperature.
[2] Certified for a maximum surface area to volume ratio of 0.8 sq. in./L when used at Cold
    (23°C) temperature.

[1] This product has also been evaluated for use in Mechanical Plumbing Device applications
    with a maximum use restriction of 2.0 square inches/L.
[2] Certified for a maximum surface area to volume ration of 2.0 square inches/L.
[G] Product is Certified to NSF/ANSI/CAN 372 and conforms with the lead content requirements
    for "lead free" plumbing as defined by California, Vermont, Maryland, and Louisiana
    state laws and the U.S. Safe Drinking Water Act.

[1] This product has also been evaluated for use in Mechanical Plumbing Device applications
    with a maximum use restriction of 2.0 square inches/L.
[2] Certified for a maximum surface area to volume ration of 2.0 square inches/L.
[G] Product is Certified to NSF/ANSI/CAN 372 and conforms with the lead content requirements
    for "lead free" plumbing as defined by California, Vermont, Maryland, and Louisiana
    state laws and the U.S. Safe Drinking Water Act.

[1] Saddle PN25
    SDL 6320 (63 x 20 mm)
    SDL 6325 (63 x 25 mm)
    SDL 6332 (63 x 32 mm)
    SDL 7520 (75 x 20 mm)
    SDL 7525 (75 x 25 mm)
    SDL 7532 (75 x 32 mm)
    SDL 9025 (90 x 25 mm)
    SDL 9032 (90 x 32 mm)
    SDL 9040 (90 x 40 mm)
    SDL 11032 (110 x 32 mm)
    SDL 11040 (110 x 40 mm)
    SDL 11050 (110 x 50 mm)
    SDL 12540 (125 x 40 mm)
    SDL 12550 (125 x 50 mm)
    SDL 12563 (125 x 63 mm)
    SDL 16040 (160 x 40 mm)
    SDL 16050 (160 x 50 mm)
    SDL 16063 (160 x 63 mm)
    SDL 20050 (200 x 50 mm)
    SDL 20063 (200 x 63 mm)
    SDL 20075 (200 x 75 mm)
    SDL 20090 (200 x 90 mm)
    SDL 25063 (250 x 63 mm)
    SDL 25075 (250 x 75 mm)
    SDL 25090 (250 x 90 mm)
    SDL 250110 (250 x 110 mm)
       
    Threaded Saddle PN25
    SDF 6320 (63 mm x 1/2")
    SDF 6325 (63 mm x 3/4")
    SDF 7520 (75 mm x 1/2")
    SDF 7525 (75 mm x 3/4")
    SDF 9020 (90 mm x 1/2")
    SDF 9025 (90 mm x 3/4")
    SDF 11020 (110 mm x 1/2")
    SDF 11025 (110 mm x 3/4")
    SDF 11032 (110 mm x 1")
[G] Product is Certified to NSF/ANSI/CAN 372 and conforms with the lead content requirements
    for "lead free" plumbing as defined by California, Vermont, Maryland, and Louisiana
    state laws and the U.S. Safe Drinking Water Act.

[1] Configurations include:
        
    Swan Neck PN20
    SOP 20 A20 (20 x 20 mm)
    SOP 25 A20 (25 x 25 mm)
    SOP 32 A20 (32 x 32 mm)
         
    Swan Neck Female - Female PN25
    SFF 2020 (20 x 20 mm)
    SFF 2525 (25 x 25 mm)
      
    Swan Neck Short Female - Female PN25
    SFC 2020 (20 x 20 mm)
    SFC 2525 (25 x 25 mm) 
       
    Socket PN25
    MAN 20 (20 x 20 mm)
    MAN 25 (25 x 25 mm)
    MAN 32 (32 x 32 mm)
    MAN 40 (40 x 40 mm)
    MAN 50 (50 x 50 mm)
    MAN 63 (63 x 63 mm)
    MAN 75 (75 x 75 mm)
    MAN 90 (90 x 90 mm)
    MAN 110 (110 x 110 mm)
    MAN 125 (125 x 125 mm)
    MAN 160 (160 x 160 mm)
    
    90° Elbow PN25
    CUV 20 (20 x 20 mm)
    CUV 25 (25 x 25 mm)
    CUV 32 (32 x 32 mm)
    CUV 40 (40 x 40 mm)
    CUV 50 (50 x 50 mm)
    CUV 63 (63 x 63 mm)
    CUV 75 (75 x 75 mm)
    CUV 90 (90 x 90 mm)
    CUV 110 (110 x 110 mm)
    CUV 125 (125 x 125 mm)
    CUV 160 (160 x 160 mm)
    CUV 160 T (160 x 160 mm)
    CUV 200 T (200 x 200 mm)
    CUV 250 T (250 x 250 mm)
        
    45° Elbow PN25
    CUQ 20 (20 x 20 mm)
    CUQ 25 (25 x 25 mm)
    CUQ 32 (32 x 32 mm)
    CUQ 40 (40 x 40 mm)
    CUQ 50 (50 x 50 mm)
    CUQ 63 (63 x 63 mm)
    CUQ 75 (75 x 75 mm)
    CUQ 90 (90 x 90 mm)
    CUQ 110 (110 x 110 mm)
    CUQ125 (125 x 125 mm)
    CUQ 160 (160 x 160 mm)
    CUQ 160 T (160 x 160 mm)
    CUQ 200 T (200 x 200 mm)
    CUQ 250 T (250 x 250 mm)
      
    90° Elbow M/F PN25
    CMF 20 (20 x 20 mm)
    CMF 25 (25 x 25 mm)
      
    Reduced 90° Elbow PN25
    CUR 2520 (25 x 20 mm)
    CUR 3220 (32 x 20 mm)
    CUR 3225 (32 x 25 mm)
      
    Reducing Bush M/F PN25
    RDZ 2520 (25 x 20 mm)
    RDZ 3220 (32 x 20 mm)
    RDZ 3225 (32 x 25 mm)
    RDZ 4020 (40 x 20 mm)
    RDZ 4025 (40 x 25 mm)
    RDZ 4032 (40 x 32 mm)
    RDZ 5020 (50 x 20 mm)
    RDZ 5025 (50 x 25 mm)
    RDZ 5032 (50 x 32 mm)
    RDZ 5040 (50 x 40 mm)
    RDZ 6320 (63 x 20 mm)
    RDZ 6325 (63 x 25 mm)
    RDZ 6332 (63 x 32 mm)
    RDZ 6340 (63 x 40 mm)
    RDZ 6350 (63 x 50 mm)
       
    Reducing Bush F/F PN25
    RDF 2520 (25 x 20 mm)
    RDF 3220 (32 x 20 mm)
    RDF 3225 (32 x 25 mm)
    RDF 4020 (40 x 20 mm)
    RDF 4025 (40 x 25 mm)
    RDF 4032 (40 x 32 mm)
    RDF 5020 (50 x 20 mm)
    RDF 5025 (50 x 25 mm)
    RDF 5032 (50 x 32 mm)
    RDF 5040 (50 x 40 mm)
    RDF 6320 (63 x 20 mm)
    RDF 6325 (63 x 25 mm)
    RDF 6332 (63 x 32 mm)
    RDF 6340 (63 x 40 mm)
    RDF 6350 (63 x 50 mm)
    RDF 7540 (75 x 40 mm)
    RDF 7550 (75 x 50 mm)
    RDF 7563 (75 x 63 mm)
    RDF 9050 (90 x 50 mm)
    RDF 9063 (90 x 63 mm)
    RDF 9075 (90 x 75 mm)
    RDF 11063 (110 x 63 mm)
    RDF 11075 (110 x 75 mm)
    RDF 11090 (110 x 90 mm)
    RDF 125110 (125 x 110 mm)
    RDF 160110 (160 x 110 mm)
    RDF 160125 (160 x 125 mm)
    RDT 200 160 (200 x 160 mm)
    RDT 250 200 (250 x 200 mm)
    RDT 250 160 (250 x 160 mm)
    
    Cap PN25
    TAC 20 (20 mm)
    TAC 25 (25 mm)
    TAC 32 (32 mm)
    TAC 40 (40 mm)
    TAC 50 (50 mm)
    TAC 63 (63 mm)
    TAC 75 (75 mm)
    TAC 90 (90 mm)
    TAC 110 (110 mm)
    TAC 125 (125 mm)
    TAC 160 T (160 mm)
    TAC 200 T (200 mm)
    TAC 250 T (250 mm)
       
    Tee PN25
    TEN 20 (20 x 20 x 20 mm)
    TEN 25 (25 x 25 x 25 mm)
    TEN 32 (32 x 32 x 32 mm)
    TEN 40 (40 x 40 x 40 mm)
    TEN 50 (50 x 50 x 50 mm)
    TEN 63 (63 x 63 x 63 mm)
    TEN 75 (75 x 75 x 75 mm)
    TEN 90 (90 x 90 x 90 mm)
    TEN 110 (110 x 110 x 110 mm)
    TEN 125 (125 x 125 x 125 mm)
    TEN 160 (160 x 160 x 160 mm)
    TEN 160 T (160 x 160 x 160 mm)
    TEN 200 T (200 x 200 x 200 mm)
    TEN 250 T (250 x 250 x 250 mm)
    
    Reducing Tee PN25
    TER 2520 (25 x 20 x 25 mm)
    TER 2521 (25 x 20 x 20 mm)
    TER 3220 (32 x 20 x 32 mm)
    TER 3225 (32 x 25 x 32 mm)
    TER 4020 (40 x 20 x 40 mm)
    TER 4025 (40 x 25 x 40 mm)
    TER 4032 (40 x 32 x 40 mm)
    TER 5020 (50 x 20 x 50 mm)
    TER 5025 (50 x 25 x 50 mm)
    TER 5032 (50 x 32 x 50 mm)
    TER 5040 (50 x 40 x 50 mm)
    TER 6320 (63 x 20 x 63 mm)
    TER 6325 (63 x 25 x 63 mm)
    TER 6332 (63 x 32 x 63 mm)
    TER 6340 (63 x 40 x 63 mm)
    TER 6350 (63 x 50 x 63 mm)
    TER 7540 (75 x 40 x 75 mm)
    TER 7550 (75 x 50 x 75 mm)
    TER 7563 (75 x 63 x 75 mm)
    TER 9050 (90 x 50 x 90 mm)
    TER 9063 (90 x 63 x 90 mm)
    TER 9075 (90 x 75 x 90 mm)
    TER 11063 (110 x 63 x 110 mm)
    TER 11075 (110 x 75 x 110 mm)
    TER 11090 (110 x 90 x 110 mm)
    TER 125110 (125 x 110 x 125 mm)
    TER 160110 (160 x 110 x 160 mm)
       
    Cross PN25
    TEQ 20 (20 x 20 x 20 x 20 mm)
        
    Union PN10
    UNI 2020 (20 x 20 mm)
    UNI 2525 (25 x 25 mm)
    UNI 3232 (32 x 32mm)
    UNI 4040 (40 x 40 mm)
    UNI 5050 (50 x 50 mm)
    UNI 6363 (63 x 63 mm)
[2] Stub End
    CTL 32 (32 mm)
    CTL 40 (40 mm)
    CTL 50 (50 mm)
    CTL 63 (63 mm)
    CTL 75 (75 mm)
    CTL 90 (90 mm)
    CTL 110 (110 mm)
    CTL 125 (125 mm)
    CTL 160 (160 mm)
    CTL 160 T (160 mm)
    CTL 200 T (200 mm)
    CTL 250 T (250 mm)
       
    Electrofusion Socket
    MAE 63 (63 x 63 mm)
    MAE 75 (75 x 75 mm)
    MAE 90 (90 x 90 mm)
    MAE 110 (110 x 110 mm)
    MAE 125 (125 x 125 mm)
    MAE 160 (160 x 160 mm)
    MAE 200 (200 x 200 mm)
    MAE 250 (250 x 250 mm)
[G] Product is Certified to NSF/ANSI/CAN 372 and conforms with the lead content requirements
    for "lead free" plumbing as defined by California, Vermont, Maryland, and Louisiana
    state laws and the U.S. Safe Drinking Water Act.

[3] Configurations include:
        
    Male Adapter Threaded Female PN25
    GFF 3220 (32 mm x 1/2")
        
    90° Threaded Elbow PN25 - Female
    CFF 2020 (20 mm x 1/2")
    CFF 2025 (20 mm x 3/4")
    CFF 2520 (25 mm x 1/2")
    CFF 2525 (25 mm x 3/4")
    CFF 3225 (32 mm x 3/4")
    CFF 3232 (32 mm x 1")
        
    90° Threaded Elbow PN25 - Male
    CFM 2020 (20 mm x 1/2")
    CFM 2025 (20 mm x 3/4")
    CFM 2520 (25 mm x 1/2")
    CFM 2525 (25 mm x 3/4")
    CFM 3225 (32 mm x 3/4")
    CFM 3232 (32 mm x 1")
        
    90° Long Threaded Elbow PN25 - Female
    CFL 2020 (20 mm x 1/2")
    CFL 2520 (25 mm x 1/2")
       
    90° Threaded Elbow with Bracket PN25 - Female
    FFS 2020 (20mm x 1/2")
    FFS 2520 (25 mm x 1/2")
    
    90° Threaded Elbow with Bracket PN25 - Male
    FMS 2020 (20 mm x 1/2")
    FMS 2520 (25 mm x 1/2")
       
    90° Threaded Elbow PN25 - Female with Male
    CCF 2020 (20 mm x 1/2")
       
    90° Threaded Elbow PN25 - Male with Male
    CCM 2020 (20 mm x 1/2")
        
    Threaded Tee PN25 - Female
    TEF 2020 (20 mm x 1/2" x 20 mm)
    TEF 2025 (20 mm x 3/4" x 20 mm)
    TEF 2520 (25 mm x 1/2" x 25 mm)
    TEF 2525 (25 mm x 3/4" x 25 mm)
    TEF 3225 (32 mm x 3/4" x 32 mm)
    TEF 3232 (32 mm x 1" x 32 mm)
       
    Threaded Tee PN25 - Male
    TEM 2020 (20 mm x 1/2" x 20 mm)
    TEM 2025 (20 mm x 3/4" x 20 mm)
    TEM 2520 (25 mm x 1/2" x 25 mm)
    TEM 2525 (25 mm x 3/4" x 25 mm)
    TEM 3225 (32 mm x 3/4" x 32 mm)
    TEM 3232 (32 mm x 1" x 32 mm)
    
    Threaded Coupling PN25 - Female
    RFF 2020 (20 mm x 1/2")
    RFF 2025 (20 mm x 3/4")
    RFF 2520 (25 mm x 1/2")
    RFF 2525 (25 mm x 3/4")
    RFF 3225 (32 mm x 3/4")
    RFF 3232 (32 mm x 1")
    RFF 4040 (40 mm x 1-1/4")
    RFF 5050 (50 mm x 1-1/2")
    RFF 6363 (63 mm x 2")
    RFF 7575 (75 mm x 2-1/2")
    RFF 9090 (90 mm x 3")
    RFF 110110 (110 mm x 4")
    
    Threaded Coupling PN25 - Male
    RFM 2020 (20 mm x 1/2")
    RFM 2025 (20 mm x 3/4")
    RFM 2520 (25 mm x 1/2")
    RFM 2525 (25 mm x 3/4")
    
    Fixed Wall Assembly Group
    GVF 2020 (20 mm x 1/2")
    GVF 2520 (25 mm x 1/2")
        
    Brass Adapter PN25 - Female
    GGF 2020 (20 mm x 1/2")
    GGF 2525 (25 mm x 3/4")
    GGF 3232 (32 mm x 1")
    GGF 4040 (40 mm x 1-1/4")
    GGF 5050 (50 mm x 1-1/2")
    GGF 6363 (63 mm x 2")
       
    Brass Adapter PN25 - Male
    GGM 2020 (20 mm x 1/2")
    GGM 2525 (25 mm x 3/4")
    GGM 3232 (32 mm x 1")
    GGM 4040 (40 mm x 1-1/")
    GGM 5050 (50 mm x 1-1/2")
    GGM 6363 (63 mm x 2")
    RFM 3225 (32 mm x 3/4")
    RFM 3232 (32 mm x 1")
    RFM 4040 (40 mm x 1-1/4")
    RFM 5050 (50 mm x 1-1/2")
    RFM 6363 (63 mm x 2")
    RFM 7575 (75 mm x 2-1/2")
    RFM 9090 (90 mm x 3")
    RFM 110110 (110 mm x 4")
       
    Wall Assembly Group
    GVS 2020 (1/2" x 1/2")
        
    Wall Assembly Group with Template
    GVD 2020 (20 mm x 1/2")
    GVD 2520 (25 mm x 1/2")
[G] Product is Certified to NSF/ANSI/CAN 372 and conforms with the lead content requirements
    for "lead free" plumbing as defined by California, Vermont, Maryland, and Louisiana
    state laws and the U.S. Safe Drinking Water Act.

[4] Pipe models include:
    
    FIBER Pipe
    TUB 20 SDR6 F
    TUB 25 SDR6 F
    
    FIBER EVO Pipe
    TUB 32 SDR9 FE
    TUB 40 SDR9 FE
    TUB 50 SDR9 FE
    TUB 63 SDR9 FE
    TUB 75 SDR9 FE
    TUB 90 SDR9 FE
    TUB 110 SDR9 FE
    TUB 125 SDR9 FE
    TUB 160 SDR9 FE
    TUB 200 SDR9 FE
    TUB 250 SDR9 FE
    TUB 20 SDR7.4 FE
    TUB 25 SDR7.4 FE
    TUB 32 SDR7.4 FE
    TUB 40 SDR7.4 FE
    TUB 50 SDR7.4 FE
    TUB 63 SDR7.4 FE
    TUB 75 SDR7.4 FE
    TUB 90 SDR7.4 FE
    TUB 110 SDR7.4 FE
    TUB 125 SDR7.4 FE
    TUB 160 SDR7.4 FE
    TUB 200 SDR7.4 FE
    TUB 250 SDR7.4 FE
    TUB 32 SDR11 FE
    TUB 40 SDR11 FE
    TUB 50 SDR11 FE
    TUB 63 SDR11 FE
    TUB 75 SDR11 FE
    TUB 90 SDR11 FE
    TUB 110 SDR11 FE
    TUB 125 SDR11 FE
    TUB 160 SDR11 FE
    TUB 200 SDR11 FE
    TUB 250 SDR11 FE
    TUB 160 SDR17 FE
    TUB 200 SDR17 FE
    TUB 250 SDR17 FE
      
    PPR Pipe
    TUB X A10 - PN10 - SDR11/S5 (20 – 63 mm)
    TUB X A16 - PN16 - SDR7.4/S3.2 (20 – 63 mm)
    TUB X A20 - PN20 - SDR6/S2.5 (20 – 63 mm)
      
    EvO Pipe
    TUB X A10 E - PN10 - SDR17/S8 (75 – 250 mm)
    TUB X A16 E - PN16 - SDR11/S5 (75 – 250 mm)
    TUB X A20 E - PN20 - SDR7.4/S3.2 (75 – 160 mm)
    TUB X A20 E - PN20 - SDR9/S4 (200 – 250 mm)
    TUB X A25 E - PN25 - SDR6/S2.5 (20 – 160 mm)
      
    X corresponds to the size in mm.
[G] Product is Certified to NSF/ANSI/CAN 372 and conforms with the lead content requirements
    for "lead free" plumbing as defined by California, Vermont, Maryland, and Louisiana
    state laws and the U.S. Safe Drinking Water Act.

[G] Product is Certified to NSF/ANSI/CAN 372 and conforms with the lead content requirements
    for "lead free" plumbing as defined by California, Vermont, Maryland, and Louisiana
    state laws and the U.S. Safe Drinking Water Act.

[G] Product is Certified to NSF/ANSI/CAN 372 and conforms with the lead content requirements
    for "lead free" plumbing as defined by California, Vermont, Maryland, and Louisiana
    state laws and the U.S. Safe Drinking Water Act.

[G] Product is Certified to NSF/ANSI/CAN 372 and conforms with the lead content requirements
    for "lead free" plumbing as defined by California, Vermont, Maryland, and Louisiana
    state laws and the U.S. Safe Drinking Water Act.
[Q] This product meets the reduced Q test statistic criteria of 1 µg or 0.5 µg for lead per
    Section 9.5.1.1 of NSF/ANSI/CAN 61.

[2] This product does not require a Q statistic. It is made from material or materials that
    do not require lead analysis when reviewed per NSF/ANSI/CAN Standard 61, Section 3.3.
[Q] This product meets the reduced Q test statistic criteria of 1 µg or 0.5 µg for lead per
    Section 9.5.1.1 of NSF/ANSI/CAN 61.

[G] Product is Certified to NSF/ANSI/CAN 372 and conforms with the lead content requirements
    for "lead free" plumbing as defined by California, Vermont, Maryland, and Louisiana
    state laws and the U.S. Safe Drinking Water Act.

[G] Product is Certified to NSF/ANSI/CAN 372 and conforms with the lead content requirements
    for "lead free" plumbing as defined by California, Vermont, Maryland, and Louisiana
    state laws and the U.S. Safe Drinking Water Act.
[Q] This product meets the reduced Q test statistic criteria of 1 µg or 0.5 µg for lead per
    Section 9.5.1.1 of NSF/ANSI/CAN 61.

[1] MFC - are models with capped outlets
    MFO - are models without capped outlets
[G] Product is Certified to NSF/ANSI/CAN 372 and conforms with the lead content requirements
    for "lead free" plumbing as defined by California, Vermont, Maryland, and Louisiana
    state laws and the U.S. Safe Drinking Water Act.

[1] Coating Notes:
    Color: Gray
    Number of Coats: 2 - 4
    Maximum Field Use Dry Thickness (in mils): 2000 mils
    Recoat Cure Time and Temperature: 1 hour at 75°F
    Final Cure Time/Temperature: 7 days @ 75°F
    Special Comments: Mix ratio is 4 quarts of water to one 60 lb bag of Cemtec Silatec PW. 
    Ensure proper surface preparation guidelines are followed prior to installation.

[1] Coating Notes:
    Color: Gray
    Number of Coats: 2 - 4
    Maximum Field Use Dry Thickness (in mils): 2000 mils
    Recoat Cure Time and Temperature: 1 hour at 75°F
    Final Cure Time/Temperature: 7 days @ 75°F
    Special Comments: Mix ratio is 4 quarts of water to one 60 lb bag of Cemtec Silatec PW. 
    Ensure proper surface preparation guidelines are followed prior to installation.

[1] Coating Notes:
    Color: Gray
    Number of Coats: 2 - 4
    Maximum Field Use Dry Thickness (in mils): 2000 mils
    Recoat Cure Time and Temperature: 1 hour at 75°F
    Final Cure Time/Temperature: 7 days @ 75°F
    Special Comments: Mix ratio is 4 quarts of water to one 60 lb bag of Cemtec Silatec PW. 
    Ensure proper surface preparation guidelines are followed prior to installation.

[1] Certified for the following configurations:
    90º Elbow PXP 1/2" - 4"
    90º Elbow FtgXP 1/2" - 4"
    Short Turn 90° Elbow PXP 1/2" - 4"
    Short Turn 90° Elbow FtgXP 1/2" - 4"
    45º Elbow PXP 1/2" - 4"
    45º Elbow FtgXP 1/2" - 4"
    Short Turn 45° Elbow PXP 1/2" - 4"
    Short Turn 45° Elbow FtgXP 1/2" - 4"
    Cap 1/2" - 4"
    Adapter PXF 1/2" - 4"
    Adapter PxM 1/2" - 4"
    Roll Stop Coupling PXP 1/2" - 4"
    No Stop Coupling PXP 1/2" - 4"
    With Stop Coupling 1/2" - 4"
    Reducing Coupling PXP 3/4" x 1/2" - 4" x 3"
    Reducing Coupling FtgXP 3/4" x 1/2" - 4" x 3"
    Tee PXPXP 1/2" - 4"
    Crossover PXP 1/2" - 3/4"
    Crossover FtgXP 1/2" - 3/4"
    Extended Coupling PXP 1/2" - 2"
    Adapter Ftg x F 1/2" - 2"
    Adapter Ftg x M 1/2" - 2"
    90° ELBOW P x F 1/2" - 2"
    90° ELBOW P x M 1/2" - 2"
    90° EXTENDED STREET ELBOW P x Ftg 3/4"
    TEE P x P x F 1/2" - 4"
    Adapter Flange P x Flange (4BOLT) 1/2" - 4"
    Adapter Flange P x Flange (8BOLT) 2 1/2" - 4"
    MANIFOLDS P x P 1" x 1/2" - 1" x 3/4"
[G] Product is Certified to NSF/ANSI/CAN 372 and conforms with the lead content requirements
    for "lead free" plumbing as defined by California, Vermont, Maryland, and Louisiana
    state laws and the U.S. Safe Drinking Water Act.

[1] This product has also been evaluated for use in Mechanical Plumbing Device applications
    with a maximum use restriction of 0.2 square inches/L.
[2] Certified for a maximum surface area to volume ratio of 2.0 square inches/L.
[G] Product is Certified to NSF/ANSI/CAN 372 and conforms with the lead content requirements
    for "lead free" plumbing as defined by California, Vermont, Maryland, and Louisiana
    state laws and the U.S. Safe Drinking Water Act.

[1] This product has also been evaluated for use in Mechanical Plumbing Device applications
    with a maximum use restriction of 0.2 square inches/L.
[2] Certified for a maximum surface area to volume ratio of 2.0 square inches/L.
[G] Product is Certified to NSF/ANSI/CAN 372 and conforms with the lead content requirements
    for "lead free" plumbing as defined by California, Vermont, Maryland, and Louisiana
    state laws and the U.S. Safe Drinking Water Act.

[1] Certified for equivalent metric sizes.
[2] YY - 02 through 48
[G] Product is Certified to NSF/ANSI/CAN 372 and conforms with the lead content requirements
    for "lead free" plumbing as defined by California, Vermont, Maryland, and Louisiana
    state laws and the U.S. Safe Drinking Water Act.

[1] For all meters:
    X - Type of electronics	
        4 - AquaMaster	
        5 - WaterMaster
        6 - ProcessMaster		
    Y - Tier of Electronics	
        1 - Standard Electronics
        2 - Enhanced Electronic
        3 - Advanced Electronics	
        5 - Premium Electronics	
    Z - Type of mounting	
        1 - Integral with transmitter
        2 - Remote with transmitter (Sensor + Transmitter)
        8 - Sensor only	
    Type of bore and liner	
        F - FEF/Full bore/Rubber liner
[G] Product is Certified to NSF/ANSI/CAN 372 and conforms with the lead content requirements
    for "lead free" plumbing as defined by California, Vermont, Maryland, and Louisiana
    state laws and the U.S. Safe Drinking Water Act.

[1] FEW XYZ A
    X - Type of electronics
        4 - AquaMaster
        5 - WaterMaster
    Y - Tier of Electronics
        1 - Standard Electronics
        2 - Enhanced Electronics
        3 - Advanced Electronics
        5 - Premium Electronics
    Z - Type of mounting
        1 - Integral with transmitter
        2 - Remote with transmitter (Sensor + Transmitter)
        8 - Sensor only

[2] For all meters:
    X - Type of electronics
        4 - AquaMaster
        5 - WaterMaster
        6 - ProcessMaster
    Y - Tier of Electronics
        1 - Standard Electronics
        2 - Enhanced Electronic
        3 - Advanced Electronics
        5 - Premium Electronics
    Z - Type of mounting
        1 - Integral with transmitter
        2 - Remote with transmitter (Sensor + Transmitter)
        8 - Sensor only
    Type of bore and liner:
    F - FEF/Full bore/Rubber liner
[3] For all meters:
        X - Type of electronics
            4 - AquaMaster
            5 - WaterMaster
        Y - Tier of Electronics
            1 - Standard Electronics
            2 - Enhanced Electronics
            3 - Advanced Electronics
            5 - Premium Electronics
        Z - Type of mounting
              1 - Integral with transmitter			
            2 - Remote with transmitter (Sensor + Transmitter)			
            8 – Sensor Only			
    
    Type of bore and liner:
    V – FEV/Optimized bore/PP liner
[4] For all meters:
        X - Type of electronics
            4 - AquaMaster
            5 - WaterMaster
        Y - Tier of Electronics
            1 - Standard Electronics
            2 - Enhanced Electronics
            3 - Advanced Electronics
            5 - Premium Electronics
        Z - Type of mounting
            1 - Integral with transmitter
            2 - Remote with transmitter (Sensor + Transmitter)
            8 – Sensor Only
    
        Type of bore and liner:
        F - FEF/Full bore/Rubber liner
        R - FER/Reduced bore/Rubber liner
[G] Product is Certified to NSF/ANSI/CAN 372 and conforms with the lead content requirements
    for "lead free" plumbing as defined by California, Vermont, Maryland, and Louisiana
    state laws and the U.S. Safe Drinking Water Act.
[G] Product is Certified to NSF/ANSI/CAN 372 and conforms with the lead content requirements
    for "lead free" plumbing as defined by California, Vermont, Maryland, and Louisiana
    state laws and the U.S. Safe Drinking Water Act.

[G] Product is Certified to NSF/ANSI/CAN 372 and conforms with the lead content requirements
    for "lead free" plumbing as defined by California, Vermont, Maryland, and Louisiana
    state laws and the U.S. Safe Drinking Water Act.

[1] This product has been evaluated for use in Piping (Section 4) applications: 
    			
    Diameter:	Length:			
    1/8" - 5/16"	No Restriction			
    3/8"    270"			
    7/16"   230"			
    1/2"    200"			
    9/16"   180"			
    5/8"    160" 			
    11/16"  145" 			
    3/4"    135" 			
    13/16" - 2" 	No Restriction
[G] Product is Certified to NSF/ANSI/CAN 372 and conforms with the lead content requirements
    for "lead free" plumbing as defined by California, Vermont, Maryland, and Louisiana
    state laws and the U.S. Safe Drinking Water Act.

[1] This product has been evaluated for use in Piping (Section 4) applications: 
    			
    Diameter:	Length:			
    1/8" - 5/16"	No Restriction			
    3/8"    270"			
    7/16"   230"			
    1/2"    200"			
    9/16"   180"			
    5/8"    160" 			
    11/16"  145" 			
    3/4"    135" 			
    13/16" - 2" 	No Restriction
[G] Product is Certified to NSF/ANSI/CAN 372 and conforms with the lead content requirements
    for "lead free" plumbing as defined by California, Vermont, Maryland, and Louisiana
    state laws and the U.S. Safe Drinking Water Act.

[1] Certified for hose assemblies in the following configurations: Stainless Steel CXC, CXE,
    Tri-clamp. All configurations of these hose assemblies are certified for a minimum
    length of 24 inches.
[G] Product is Certified to NSF/ANSI/CAN 372 and conforms with the lead content requirements
    for "lead free" plumbing as defined by California, Vermont, Maryland, and Louisiana
    state laws and the U.S. Safe Drinking Water Act.

[2] This product has been evaluated for use in Piping (Section 4) applications with the
    following length restrictions:
    Diameter    Maximum Length
    1/8"        No Restriction
    3/16"       No Restriction
    1/4"        No Restriction
    5/16"       No Restriction
    3/8"        270"
    7/16"       230"
    1/2"        200"
    9/16"       180"
    5/8"        160"
    11/16"      145"
    3/4"        135"
    13/16"      No Restriction
    7/8"        No Restriction
    15/16"      No Restriction
    1"          No Restriction
    1 1/8"      No Restriction
    1 3/16"     No Restriction
    1 1/4"      No Restriction
    1 5/16"     No Restriction
    1 3/8"      No Restriction
    1 7/16"     No Restriction
    1 1/2"      No Restriction
    1 9/16"     No Restriction
    1 5/8"      No Restriction
    1 11/16"    No Restriction
    1 3/4"      No Restriction
    2"          No Restriction

[1] Certified for product with the following densities and reaction speeds:
    2 pounds per cubic foot (regular speed)
    2 pounds per cubic foot (fast speed)
    3 pounds per cubic foot (regular speed)
    3 pounds per cubic foot (fast speed)
    4 pounds per cubic foot (slow speed)
    4 pounds per cubic foot (regular speed)
    4 pounds per cubic foot (fast speed)
    5 pounds per cubic foot (regular speed)
    6 pounds per cubic foot (regular speed)
    
    Mix ratio is 1:1 (A:B) by volume or 8.1:6.9 (A:B) by weight.
    Minimum cure time is 60 minutes at ambient temperatures.
[2] Certified for a maximum surface area to volume ratio of 0.375 square inches per liter.

[1] Colors: Blue
    Number of Coats: 1-5
    Maximum Field Use Dry Thickness (in mils): 100 mils (50 per coat)
    Recoat Cure Time and Temperature: Immediate
    Final Cure Time/Temperature: 3 days at 72° F
    Special Comments: Mix ratio of Part A to Part B is 1:1 by volume. This material is
    applied using a high-pressure plural component pump.

[1] Colors: Blue
    Number of Coats: 1-5
    Maximum Field Use Dry Thickness (in mils): 100 mils (50 per coat)
    Recoat Cure Time and Temperature: Immediate
    Final Cure Time/Temperature: 3 days at 72° F
    Special Comments: Mix ratio of Part A to Part B is 1:1 by volume. This material is
    applied using a high-pressure plural component pump.

[1] Colors: Blue
    Number of Coats: 1-5
    Maximum Field Use Dry Thickness (in mils): 100 mils (50 per coat)
    Recoat Cure Time and Temperature: Immediate
    Final Cure Time/Temperature: 3 days at 72° F
    Special Comments: Mix ratio of Part A to Part B is 1:1 by volume. This material is
    applied using a high-pressure plural component pump.

[1] Certified for product with the following densities and reaction speeds:
    2 pounds per cubic foot (regular speed)
    2 pounds per cubic foot (fast speed)
    3 pounds per cubic foot (regular speed)
    3 pounds per cubic foot (fast speed)
    4 pounds per cubic foot (slow speed)
    4 pounds per cubic foot (regular speed)
    4 pounds per cubic foot (fast speed)
    5 pounds per cubic foot (regular speed)
    6 pounds per cubic foot (regular speed)
    
    Mix ratio is 1:1 (A:B) by volume or 8.1:6.9 (A:B) by weight.
    Minimum cure time is 60 minutes at ambient temperatures.
[2] Certified for a maximum surface area to volume ratio of 0.375 square inches per liter.

[G] Product is Certified to NSF/ANSI/CAN 372 and conforms with the lead content requirements
    for "lead free" plumbing as defined by California, Vermont, Maryland, and Louisiana
    state laws and the U.S. Safe Drinking Water Act.

[1] The variables in the trade name denote the following:
    "NN" refers to outlet size, ranging from 32 mm to 300 mm.
    "YY" refers to impeller diameter, ranging from 13 cm - 50 cm.
    "G" is an optional designation indicating High Speed.
[G] Product is Certified to NSF/ANSI/CAN 372 and conforms with the lead content requirements
    for "lead free" plumbing as defined by California, Vermont, Maryland, and Louisiana
    state laws and the U.S. Safe Drinking Water Act.

[1] Certified for a maximum surface area to volume ratio of 0.3 sq. in./L in pipe or 1% of a
    20,000 gallon tank.
[2] To obtain the proper mix, use at least a 3/4" length, but no more than 1/3 of a full
    stick, of product which has been cut with a knife. Product must be mixed for 60-90
    seconds.
[G] Product is Certified to NSF/ANSI/CAN 372 and conforms with the lead content requirements
    for "lead free" plumbing as defined by California, Vermont, Maryland, and Louisiana
    state laws and the U.S. Safe Drinking Water Act.

[1] (1) Hose length
    (2) Packaging options (M, F, E, EL, CF, CM, PF, FM, XM, XF, XE, XL, XC, or R)
[Q] This product meets the reduced Q test statistic criteria of 1 µg or 0.5 µg for lead per
    Section 9.5.1.1 of NSF/ANSI/CAN 61.

[1] (1) Hose length
    (2) Packaging options (M, F, E, EL, CF, CM, PF, FM, XM, XF, XE, XL, XC, or R)
[G] Product is Certified to NSF/ANSI/CAN 372 and conforms with the lead content requirements
    for "lead free" plumbing as defined by California, Vermont, Maryland, and Louisiana
    state laws and the U.S. Safe Drinking Water Act.

[1] (1) Hose length
    (2) Packaging options (M, F, E, EL, CF, CM, PF, FM, XM, XF, XE, XL, XC, or R)
[G] Product is Certified to NSF/ANSI/CAN 372 and conforms with the lead content requirements
    for "lead free" plumbing as defined by California, Vermont, Maryland, and Louisiana
    state laws and the U.S. Safe Drinking Water Act.

[1] (1) Hose length
    (2) Packaging options (M, F, E, EL, CF, CM, PF, FM, XM, XF, XE, XL, XC, or R)
[G] Product is Certified to NSF/ANSI/CAN 372 and conforms with the lead content requirements
    for "lead free" plumbing as defined by California, Vermont, Maryland, and Louisiana
    state laws and the U.S. Safe Drinking Water Act.

[G] Product is Certified to NSF/ANSI/CAN 372 and conforms with the lead content requirements
    for "lead free" plumbing as defined by California, Vermont, Maryland, and Louisiana
    state laws and the U.S. Safe Drinking Water Act.

[1] Configuration code breakdown: 
    P  – PushOn 
    F  – Fitting 
    50 - 1/2" 
    75 - 3/4" 
    M  – Manifold 
    T  – Tee 
    C  – Coupling 
    E  – Elbow 
    X  – Compatible with PEX pipe (as well as copper and CPVC) 
    E  – Bulk packaged (each)
[2] PF50MT XE – 1/2" PushOnManifold Tee Code: 
    P  – PushOn 
    F  – Fitting 
    50 – 1/2 inch 
    M  – Manifold 
    T  – Tee 
    X  – Compatible with PEX pipe (as well as copper and CPVC). 
    E  – Bulk packaged (each)
[G] Product is Certified to NSF/ANSI/CAN 372 and conforms with the lead content requirements
    for "lead free" plumbing as defined by California, Vermont, Maryland, and Louisiana
    state laws and the U.S. Safe Drinking Water Act.

[1] Trade name may feature prefix "E" to denote product sold in Europe.
[2] Suffix denotes color for the outermost layer. Color codes are:
    BK - Black
    BL - Blue
    W  - White
    G  - Light Grey
    GR - Green
    DG - Dark Grey
    R  - Red
[3] YYY denotes color for the outermost layer. Color codes are:
    BLK  - Black
    BLU  - Blue
    DGRY - Dark Gray
    GRN  - Green
    LGRY - Light Gray 
    RED  - Red
    WHT  - White
[G] Product is Certified to NSF/ANSI/CAN 372 and conforms with the lead content requirements
    for "lead free" plumbing as defined by California, Vermont, Maryland, and Louisiana
    state laws and the U.S. Safe Drinking Water Act.

[1] Colors: Red
    Number of Coats: 1
    Maximum Field Use Dry Thickness (in mils): 4-500
    Final Cure Time/Temperature: 15 minutes in water at a service temperature of 23C and
    greater.
    Special Comments: Mix ratio of A:B is 2:1 by volume. Product shall be preconditioned to
    at least 95F prior to mixing. Induction time is at least 10 minutes. Cure with air at a
    minimum of 95F for at least 2 hours. Following the air cure, product cure shall continue
    in water at a service temperature of 23C and greater for 15 minutes with a flow rate of
    1 to 5 liters per minute prior to being placed into service.
[2] Certified for Immediate Return to Service. 

[1] Certified for the following tank/component combinations:
    3/4" fittings/fitting gaskets shall only be used with tanks greater than or equal to 2.8
    gallons.
    1" fittings/fitting gaskets shall only be used with tanks greater than or equal to 3
    gallons.
    1-1/4" and 1-1/2" fittings/fitting gaskets shall only be used with tanks greater than or
    equal to 4 gallons.
    2" fittings/fitting gaskets shall only be used with tanks greater than or equal to 5
    gallons.
    3" fittings/fitting gaskets shall only be used with tanks greater than or equal to 95
    gallons.
    Siphon tubes shall only be used with tanks greater than or equal to 5 gallons.
[2] The trade names include product information represented by alphanumeric code, denoted as
    follows:										
    XXXX, XXXXX, XXXXXX: Tank volume in gallons (2.8 gallons and greater)										
    YY, YYY, YYYY diameter/width of tank in inches										
    QQ: Customer code										
    Z: Can be S (sump) or W (no sump)										
    UU: Can be RT (Rectangular Tank), SQ (Square Tank), 2P (2in lid), 5N (5 in lid), or any
    other two alphabetical code (customer code)										
    VVVVV: Part number										
    #: Lid size in inches.

[1] Certification is based on a bed depth up to 65 cm with a minimum flow rate of 3.82 cubic
    meter per hour per sq. meter.
[2] Certified for mesh size 0.8 x 1.5 mm.

[1] The following part numbers, configurations and sizes are Certified.  All manifolds are
    72" long (unless otherwise noted) and may be cut to the desired length.
    
    Copper Manifolds with Copper Ports:
    
    Pipe run 1", 1 1/4", 1 1/2" or 2" with 24 1/2", 3/4", or 1" copper outlets on 3" CTRS.
    
    CC1005024 1 X 1/2 CU
    CC1255024 1 1/4 X 1/2 CU
    CC1251024 1 1/4 X 1 CU
    CC1505024 1 1/2 X 1/2 CU
    CC1501024 1 1/2 X 1 CU
    CC2005024 2 X 1/2 CU
    CC1007524 1 X 3/4 CU
    CC1257524 1 1/4 X 3/4 CU
    CC1507524 1 1/2 X 3/4 CU
    CC2007524 2 X 3/4 CU
    CC2001024 2 X 1 CU
    
    Pipe run 1", 1 1/4", 1 1/2" or 2" with 18 1/2", 3/4", or 1" copper outlets on 4" CTRS
    
    CC1005018 1 X 1/2 CU
    CC1255018 1 1/4 X 1/2 CU
    CC1505018 1 1/2 X 1/2 CU
    CC2005018 2 X 1/2 CU
    CC1007518 1 X 3/4 CU
    CC1257518 1 1/4 X 3/4 CU
    CC1507518 1 1/2 X 3/4 CU
    CC2007518 2 X 3/4 CU
    CC1251018 1 1/4 X 1 CU
    CC1501018 1 1/2 X 1 CU
    CC2001018 2 X 1 CU
    
    Pipe run 1", 1 1/4", 1 1/2" or 2" with 12 1/2", 3/4", or 1" copper outlets on 6" CTRS.
    
    CC1005012ER 1 X 1/2 CU
    CC1255012ER 1 1/4 X 1/2 CU
    CC1505012ER 1 1/2 X 1/2 CU
    CC2005012ER 2 X 1/2 CU
    CC1007512ER 1 X 3/4 CU
    CC1257512ER 1 1/4 X 3/4 CU
    CC1507512ER 1 1/2 X 3/4 CU
    CC2007512ER 2 X 3/4 CU
    CC1251012ER 1 1/4 X 1 CU
    CC1501012ER 1 1/2 X 1 CU
    CC2001012ER 2 X 1 CU
    
    Pipe run 62" long, 1" with 30 1/2" copper outlets on 2" CTRS.
    
    CC1005030 1 X 1/2 CU
    
    Compact Headers - Pipe run 1" with 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, or 12 1/2" copper
    outlets on 1 1/2" CTRS.
    
    CC1005002 1 X 1/2 CU
    CC1005003 1 X 1/2 CU
    CC1005004 1 X 1/2 CU
    CC1005005 1 X 1/2 CU
    CC1005006 1 X 1/2 CU
    CC1005007 1 X 1/2 CU
    CC1005008 1 X 1/2 CU
    CC1005009 1 X 1/2 CU
    CC1005010 1 X 1/2 CU
    CC1005011 1 X 1/2 CU
    CC1005012 1 X 1/2 CU
    
    Speedy Copper Headers - closed one end and reduced 3/4" female sweat the other end.
    
    SC1005002RC 1 X 1/2 CU
    SC1005003RC 1 X 1/2 CU
    SC1005004RC 1 X 1/2 CU
    SC1005005RC 1 X 1/2 CU
    SC1005006RC 1 X 1/2 CU
    SC1005007RC 1 X 1/2 CU
    SC1005008RC 1 X 1/2 CU
    SC1005009RC 1 X 1/2 CU
    SC1005010RC 1 X 1/2 CU
    SC1005011RC 1 X 1/2 CU
    SC1005012RC 1 X 1/2 CU
    
    Speedy Copper Headers - closed one end and 1" plain the other end.
    
    SC1005002PL 1 X 1/2 CU
    SC1005003PL 1 X 1/2 CU
    SC1005004PL 1 X 1/2 CU
    SC1005005PL 1 X 1/2 CU
    SC1005006PL 1 X 1/2 CU
    SC1005007PL 1 X 1/2 CU
    SC1005008PL 1 X 1/2 CU
    SC1005009PL 1 X 1/2 CU
    SC1005010PL 1 X 1/2 CU
    SC1005011PL 1 X 1/2 CU
    SC1005012PL 1 X 1/2 CU
    
    Copper Manifolds with PEX Valves:
    
    Type L Copper Manifold with a Lead Free PEX Valve
    1", 1 1/4", 1 1/2", and 2" Copper Headers with 1/2" Lead Free PEX Valves on 3" Center
    
    CX1005024V-LF 1" x 1/2" Copper outlets with a 1/2" Lead free PEX Valve
    CX1255024V-LF 1 1/4" x 1/2" Copper outlets with a 1/2" Lead free PEX Valve
    CX1505024V-LF 1 1/2" x 1/2" Copper outlets with a 1/2" Lead free PEX Valve
    CX2005024V-LF 2" x 1/2" Copper outlets with a 1/2" Lead free PEX Valve
    
    1" or 1 1/4" Copper Header with 2-12 1/2" Lead Free PEX Valves on 2" Centers
    CVP1005002-LF
    CVP1005003-LF
    CVP1005004-LF
    CVP1005005-LF
    CVP1005006-LF
    CVP1005007-LF
    CVP1005008-LF
    CVP1005009-LF
    CVP1005010-LF
    CVP1005011-LF
    CVP1005012-LF
    CVP1255002-LF
    CVP1255002-LF
    CVP1255003-LF
    CVP1255004-LF
    CVP1255005-LF
    CVP1255006-LF
    CVP1255007-LF
    CVP1255008-LF
    CVP1255009-LF
    CVP1255010-LF
    CVP1255011-LF
    CVP1255012-LF
    

[1] This product is Certified for a maximum use level of 125 mg/L.
[G] Product is Certified to NSF/ANSI/CAN 372 and conforms with the lead content requirements
    for "lead free" plumbing as defined by California, Vermont, Maryland, and Louisiana
    state laws and the U.S. Safe Drinking Water Act.

[1] The carbon source is coconut shell.
[2] Certified for the following mesh sizes: 3x6, 3x30, 6x8, 4x8, 6x12, 6x16, 8x16, 8x20,
    8x30, 12x30, 12x40, 14x25, 16x35, 16x40, 18x35, 18x40, 20x40, 20x50, 20x60, 20x70,
    30x50, 30x60, 30x70, 30x80, 35x60, 35x70 and 40x80.

[1] The carbon source is coconut shell.
[3] Certified for the following mesh sizes: 40x140, 50x140, 50x200, 80x140, 80x200, 80x325,
    100x325, -200 and -325.

[1] The carbon source is coconut shell.
[2] Certified for mesh sizes: 4 x 10, 6 x 16, 8 x 20, 8 x 40, 10 x 20, 10 x 30, 10 x 32, 12
    x 20, 12 x 35, 12 x 40, 18 x 30, 18 x 35, 20 x 50, 30 x 70, 30 x 80,
    30 x 100, 30 x 140.
[3] Certified for mesh sizes: 4 x 8, 4 x 10, 6 x 10, 6 x 12, 6 x 16, 8 x 16, 8 x 20, 8 x 40,
    8 x 30, 10 x 20, 10 x 30, 10 x 32, 12 x 20, 12 x 30, 12 x 35, 12 x 40, 14 x 35, 18 x 30,
    18 x 35, 18 x 40, 20 x 40, 20 x 50, 30 x 20, 30 x 60, 30 x 70, 30 x 80, 30 x 100, 30 x
    140, 35 x 60, 40 x 80, 40 x 100, 40 x 140, 50 x 100, 50 x 200, 60 x 140, 60 x 200, 60 x
    320, 80 x 200, 80 x 325, -100, -200, -325.

[1] The carbon source is coconut shell.
[3] Certified for mesh sizes: 4 x 8, 4 x 10, 6 x 10, 6 x 12, 6 x 16, 8 x 16, 8 x 20, 8 x 40,
    8 x 30, 10 x 20, 10 x 30, 10 x 32, 12 x 20, 12 x 30, 12 x 35, 12 x 40, 14 x 35, 18 x 30,
    18 x 35, 18 x 40, 20 x 40, 20 x 50, 30 x 20, 30 x 60, 30 x 70, 30 x 80, 30 x 100, 30 x
    140, 35 x 60, 40 x 80, 40 x 100, 40 x 140, 50 x 100, 50 x 200, 60 x 140, 60 x 200, 60 x
    320, 80 x 200, 80 x 325, -100, -200, -325.

[1] The carbon source is coconut shell.
[2] Certified for the following mesh sizes: All mesh sizes between US ASTM 3 - 325.

[1] Certified for use in distribution systems only.

[1] Certified for the following mesh sizes: 8 x 20, 20 x 40.

[1] Certified for a maximum of 18.5 joints per liter.

[1] Certified for use as an anchoring adhesive for installing thread rods (less than or
    equal to 1.3 inches in diameter) in concrete or masonry for water treatment applications.

[1] Certified for use as an anchoring adhesive for installing threaded rods (less than or
    equal to 6 mm - 36 mm or 1/4" - 1-3/8" in diameter) in concrete for water treatment
    applications.

[1] Certification is based on a minimum cure of 72 hours at 75°F.

[1] Certified for use as an anchoring adhesive for installing thread rods (less than or
    equal to 1.3 inches in diameter) in concrete or masonry for water treatment applications.

[G] Product is Certified to NSF/ANSI/CAN 372 and conforms with the lead content requirements
    for "lead free" plumbing as defined by California, Vermont, Maryland, and Louisiana
    state laws and the U.S. Safe Drinking Water Act.

[1] Certified for 1/8" thick flange insulating gaskets.

[1] YY: 		
    BB - OUTLET PIPE is brass, OUTLET is brass		
    SS - OUTLET PIPE is stainless steel, OUTLET is stainless steel 		
    BS - OUTLET PIPE is brass, OUTLET is stainless steel 		
    SB - OUTLET PIPE is stainless steel, OUTLET is brass
    BP - OUTLET PIPE is brass, OUTLET is PP		
    SP - OUTLET PIPE is stainless steel, OUTLET is PP		
    
[2] (1)-(2)
    (1) Outlet pipe - L type: L 
        C type: C, 2C, 12C
    (2) Outlet pipe length: 250 - 500mm
        Blank - Standard: C-300, 2C-280, 12C-390
    
[3] (3)-(4)		
    (3) Shank type:		
        1/4OD		
        2Q  - 1/4" push in connector		
        3Q  - 3/8" push in connector		
        WJZ - With tubing, J - PE length:  20~200cm, Z - PE tube color ( various colors)		
    		
    (4) Shank length: 2" - 4"		
        Blank - Standard - 1/4OD-3		
    
[4] A     - Air gap
    Blank - Standard: without air gap
    
[5] XX - Various color
    
[Q] This product meets the reduced Q test statistic criteria of 1 µg or 0.5 µg for lead per
    Section 9.5.1.1 of NSF/ANSI/CAN 61.

[1] Certified for the following tubing colors: 
    Black 
    Blue 
    Green 
    Natural  
    Red 
    White
    Yellow
[2] Certified for the following sizes: 
    5/32 " - 1"
    4 mm - 16 mm

[1] Certified for a maximum surface area to volume ratio of 50 sq. in./L.
[2] Certified for a maximum surface are to volume ratio of 20 sq. in./L.

[1] Certified for the following sizes:
    0.3 - 3 mm
    20x14, 35x18 and 45x20 mesh

[1] Certified for the following sizes:
    0.3 - 3 mm
    20x14, 35x18 and 45x20 mesh

[1] Certified for a maximum surface area to volume ratio of 2.0 square inches/L.
[2] This product has also been evaluated for use in Mechanical Plumbing Device applications
    with a maximum use restriction of 2.0 square inches/L.
[G] Product is Certified to NSF/ANSI/CAN 372 and conforms with the lead content requirements
    for "lead free" plumbing as defined by California, Vermont, Maryland, and Louisiana
    state laws and the U.S. Safe Drinking Water Act.

[1] Certified for a maximum surface area to volume ratio of 2.0 square inches/L.
[2] This product has also been evaluated for use in Mechanical Plumbing Device applications
    with a maximum use restriction of 2.0 square inches/L.
[G] Product is Certified to NSF/ANSI/CAN 372 and conforms with the lead content requirements
    for "lead free" plumbing as defined by California, Vermont, Maryland, and Louisiana
    state laws and the U.S. Safe Drinking Water Act.

[1] YY:
    BB - OUTLET PIPE is brass ,  OUTLET is brass
    SS - OUTLET PIPE is stainless steel , OUTLET is stainless steel
    BS - OUTLET PIPE is brass , OUTLET is stainless steel
    SB - OUTLET PIPE is stainless steel , OUTLET is brass
    BP - OUTLET PIPE is brass , OUTLET is PP
    SP - OUTLET PIPE is stainless steel , OUTLET is PP
[2] (1)-(2)
    (1) OUTLET PIPE 
          - C type : C, 2C, 12C
    (2) OUTLET PIPE length  : 250~500mm
          Blank - Standard: C-300, 2C-280, 12C-390
[3] (1)-(2)
    (1) OUTLET PIPE 
          - L type : L
          - C type : C, 2C, 12C
    (2) OUTLET PIPE length  : 250~500mm
          Blank - Standard: C-300, 2C-280, 12C-390
[4] (1)-(2)	
    (1) OUTLET PIPE 
          - C type : 2C 
    (2) OUTLET PIPE length  : 250~500mm
          Blank - Standard: C-300, 2C-280, 12C-390
[5] (3)-(4)
    (3) Shank type:
          1/4OD
          2Q - 1/4"" push in connector
             3Q - 3/8"" push in connector
             WJZ - With tubing, J - PE length:  20~200cm, Z - PE tube color (various colors)
    (4) Shank length: 2""~4""
          Blank - Standard - 1/4OD-3	
[6] A - air gap
    Blank - Standard: without air gap
[7] XX - Various color
[8] EEEE:
    6301
    6302
    6303
    6305
    6401A
    6401
    6402
    6403
    6405
    6406A
    6406
    6407
    6501N
    6501
    6502N
    6502
    6503N
    6503
    6505N
    6505
    6701
    6702
    6703
    6705
    6706
    6707
    6708
    6709
[9] FFFF:
    6401
    6402
    6403
    6501
    6502
    6601
    6602
    6605
    6608
    6703
    6705
    6708
    6709
[10] GGGG:
     6103B
     6103
     6104B
     6104
     61031
     61041
[11] HHHH:
     6108
     6109B
     6109
     61081
     61091
[LL] Product conforms with lead content requirements for “lead free” plumbing as defined by
     California, Vermont, Maryland, and Louisiana state laws and the U.S. Safe Drinking Water
     Act.

[1] YY:
    BB - OUTLET PIPE is brass ,  OUTLET is brass
    SS - OUTLET PIPE is stainless steel , OUTLET is stainless steel
    BS - OUTLET PIPE is brass , OUTLET is stainless steel
    SB - OUTLET PIPE is stainless steel , OUTLET is brass
    BP - OUTLET PIPE is brass , OUTLET is PP
    SP - OUTLET PIPE is stainless steel , OUTLET is PP
[Q] This product meets the reduced Q test statistic criteria of 1 µg or 0.5 µg for lead per
    Section 9.5.1.1 of NSF/ANSI/CAN 61.

[1] The carbon source is coconut shell.
[2] Trade names may include letters and/or numbers to designate any or all of the following:
    mesh size, customer, processing methods, intended applications, activity level (iodine
    number), special testing, or other customer or product specific differentiators.
[3] Certified for the following mesh sizes: 3x6, 4x6, 4x8, 4x10, 6x8, 6x10, 6x12, 6x16,
    8x12, 8x14, 8x16, 8x20, 8x24, 8x30, 8x40, 10x20, 10x30, 10x40, 10x100, 12x20, 12x30,
    12x40, 14x30, 14x40, 16x30, 16x40,18x35, 18x40, 18x50, 20x30, 20x40, 20x50, 20x60,
    20x70, 25x60, 30x40, 30x50, 30x60, 30x70, 30x100, 30x200, 40x80, 40x100, 40x140, 40x200,
    50x100, 50x140, 50x200, 60x100, 60x120, 60x200, 80x100, 80x200, 80x325, 100x325, -100,
    -200 and -325.