NSF Product and Service Listings

These NSF Official Listings are current as of Saturday, September 20, 2014 at 12:15 a.m. Eastern Time. Please contact NSF International to confirm the status of any Listing, report errors, or make suggestions.

Alert: NSF is concerned about fraudulent downloading and manipulation of website text. Always confirm this information by clicking on the below link for the most accurate information: http://info.nsf.org/Certified/PwsComponents/Listings.asp?StandardExt=JSM&



NSF/ANSI 61
Drinking Water System Components - Health Effects

NOTE: Unless otherwise indicated for Materials, Certification is only for the Water Contact Material shown in the Listing. Click here for a list of Abbreviations used in these Listings.


 
A. W. Chesterton Co. 
225 Fallon Road
P.O. Box 9101 
Stoneham, MA 02180-9101 
United States 
617-438-7000

Facility : # 1 USA

Joining and Sealing Materials

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Patching Materials
ARC 5ES [1] C. HOT EPOXY

[1] The exposed surface area of each sealant in a household distribution system
    should not exceed 1.3 sq. cm/L or .2 sq. in/L.



 
Access-Able Technologies, Inc. 
1275 Bennett Drive #115
Longwood, FL 32750 
United States 
800-572-4894 
407-834-2999

Facility : # 1 USA

Joining and Sealing Materials

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Patching Materials [G]
Pow-R Stick Steel Hard Epoxy Putty (Copper Color) [1] [2] C. HOT EPOXY
Pow-R Stick Steel Hard Epoxy Putty (Grey Color) [1] [2] C. HOT EPOXY
Pow-R Stick Steel Hard Epoxy Putty (White Color) [1] [2] C. HOT EPOXY
STIC-O-STEEL POW-R Putty [1] [2] C. HOT EPOXY

[1] Certified for a maximum surface area to volume ratio of 0.3 sq. in./L in pipe or 1% of a
    20,000 gallon tank.
[2] To obtain the proper mix, use at least a 3/4" length, but no more than 1/3 of a full
    stick, of product which has been cut with a knife. Product must be mixed for 60-90
    seconds.
[G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for
    “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state
    laws and the U.S. Safe Drinking Water Act.

    



 
Adeka Corporation 
7-2-35 Higashiogu
Arakawa-ku, Toyko, 116-8554 
Japan 
81 3 4455 2843
Visit this company's website

Facility : Ibaraki, Japan

Joining and Sealing Materials

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Gasket/Sealing Materials
MC-2010MN [1] CLD 23 IR

[1] Certified for a maximum surface area to volume ratio not to exceed 0.13 sq. in./L.



 
Adhesive Technology Corp. 
450 East Copans Road
Pompano Beach, FL 33064 
United States 
954-782-2221

Facility : WH09 USA

Joining and Sealing Materials

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Adhesives
Ultrabond 365 [1] CLD 23 ACR

[1] Certified for use at a maximum surface area to volume ratio of 0.0005 sq. in./L in a
    tank.



 
Adolf Würth GmbH & Co. KG 
Reinhold-Würth-Str. 12-17
Baden-Württemberg 
74650 Künzelsau 
Germany 
49 7940 15 0

Facility : Fridolfing, Germany

Joining and Sealing Materials

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Sealants
Acetatsilicon Lebensmittel [1] CLD 23 SLT

[1] Certified for a maximum surface area to volume ratio of 7.3 sq. in./L.



 
Adolf Würth GmbH & Co. KG 
Produktmanagement Chemie, Postfach
74650 Künzelsau 
Germany 
49 794 015 2007

Facility : # 1 Switzerland

Joining and Sealing Materials

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Adhesives
Würth®saBesto DOS Schraubensicherung Hochfest >= 1/2" C. HOT ADH
Würth® saBesto DOS Schraubensicherung Mittelfest >= 1/2" C. HOT ADH
Würth® saBesto DOS Rohrdicht mit PTFE >= 1/2" C. HOT ADH
Würth saBesto Rohrdicht PLUS (0893 577 300) >= 1/2" C. HOT ADH

Thread Compounds
Würth® saBesto DOS Rohrdicht[1] >= 1/2" C. HOT TC
Würth®saBesto DOS Schraubensicherung Hochfest >= 1/2" C. HOT TC
Würth® saBesto DOS Rohrdicht mit PTFE >= 1/2" C. HOT TC

[1] Certification is based on a minimum cure of 72 hours at 75°F.



 
Adolf Würth GmbH & Co. KG 
Reinhold-Würth-Str. 12-16
74653 Künzelsau-Gaisbach 
Germany 
49 7940 15 0

Facility : # 2 Germany

Joining and Sealing Materials

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Adhesives
Atrion AVM TOP QUATTRO [1] D. HOT VE
WIT-PE 500 [1] D. HOT EPOXY
WIT-VM 250 [1] D. HOT VE

[1] Certified for use as an anchoring adhesive for installing thread rods (less than or
    equal to 1.3 inches in diameter) in concrete or masonry for water treatment applications.



 
Adolf Würth GmbH & Co. KG 
Reinhold-Würth-Strasse 12-17
D-74650 Künzelsau, Baden-Wurttemberg 
Germany 
49 7940150
Visit this company's website

Facility : # 1 Germany

Joining and Sealing Materials

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Sealants
SILICONE ACETATE, FOOD GRADE / ACETATSILIKON LEBENSMITTEL >= 1/2" CLD 23 SLT



 
Air Logistics Corp. 
925 North Todd Avenue
Azusa, CA 91702 
United States 
626-633-0294

Facility : Azusa, CA

Joining and Sealing Materials

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Sealants
Aquapreg™ 2.0 sq. in./L C. HOT SLT
Aquawrap™ 2.0 sq. in./L C. HOT SLT



 
AJ New Material 
18 Hua Shi East Road
Tong Xiang Long Xiang Industrial Park 
Zhejiang 314500 
China 
86 573 8879 7122

Facility : Zhejiang, China

Joining and Sealing Materials

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Gasket/Sealing Materials [G]
AJG-Gasket [1] D. HOT EPDM
AJG-ORing [1] D. HOT EPDM
AJG-URing [1] D. HOT EPDM
AJG-VRing [1] D. HOT EPDM
AJG-XRing [1] D. HOT EPDM
AJG-YRing [1] D. HOT EPDM

[1] Certified for a maximum surface area to volume ratio of 2.0 sq. in./L.
[G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for
    “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state
    laws and the U.S. Safe Drinking Water Act.

    



 
American Polywater Corporation 
11222 60th Street North
Stillwater, MN 55082 
United States 
800-328-9384 
651-430-2270
Visit this company's website

Facility : Stillwater, MN

Joining and Sealing Materials

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Lubricants
Grand Slam™ Pipe Joint Lubricant Type GSQ-128 N/A CLD 23 LUB
Grand Slam™ Pipe Joint Lubricant Type GSQ-128A N/A CLD 23 LUB
Grand Slam™ Pipe Joint Lubricant Type GSQ-35 N/A CLD 23 LUB
Grand Slam™ Pipe Joint Lubricant Type GSQ-35A N/A CLD 23 LUB
Grand Slam™ Pipe Joint Lubricant Type GSQ-448 N/A CLD 23 LUB
Grand Slam™ Pipe Joint Lubricant Type GSQ-448A N/A CLD 23 LUB
Grand Slam™ Pipe Joint Lubricant Type GSQ-55DRUMA N/A CLD 23 LUB
Grand Slam™ Pipe Joint Lubricant Type GSQ-640 N/A CLD 23 LUB
Grand Slam™ Pipe Joint Lubricant Type GSQ-640A N/A CLD 23 LUB
Grand Slam™ Pipe Joint Lubricant Type Wintergrade Formula GWQ-128 N/A CLD 23 LUB
Grand Slam™ Pipe Joint Lubricant Type Wintergrade Formula GWQ-128A N/A CLD 23 LUB
Grand Slam™ Pipe Joint Lubricant Type Wintergrade Formula GWQ-35 N/A CLD 23 LUB
Grand Slam™ Pipe Joint Lubricant Type Wintergrade Formula GWQ-35A N/A CLD 23 LUB
Grand Slam™ Pipe Joint Lubricant Type Wintergrade Formula GWQ-448 N/A CLD 23 LUB
Grand Slam™ Pipe Joint Lubricant Type Wintergrade Formula GWQ-448A N/A CLD 23 LUB
Grand Slam™ Pipe Joint Lubricant Type Wintergrade Formula GWQ-640 N/A CLD 23 LUB
Grand Slam™ Pipe Joint Lubricant Type Wintergrade Formula GWQ-640A N/A CLD 23 LUB



 
Andhra Polymers Private Limited 
Plot No. 2, Phase V
Ida Jeedimetla 
Hyderabad, Andhrapradesh 500 055 
India 
91 40 2344 9248

Facility : Hyderabad, India

Joining and Sealing Materials

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Gasket/Sealing Materials[1]
APPL/FC [2] D. HOT EPDM
APPL/FS [2] D. HOT EPDM
APPL/LR [2] D. HOT EPDM
APPL/SG [2] D. HOT EPDM
EP-48 [3] D. HOT EPDM
EP-55 [3] D. HOT EPDM

[1] Only products bearing the NSF Mark are Certified.
[2] APPL/FC, APPL/FS, APPL/LR and APPL/SG pipe gaskets are molded from EP-48 or EP-55 in 75
    mm and larger diameters. Certified for use in 75 mm and larger diameter pipes with a
    maximum 1/2" exposed gasket width.
[3] EP-48 and EP-55 compounds are molded into other gasket and o-ring seals. Certified for a
    maximum surface area to volume ratio of 2 sq. in./L.

O-Rings[1]
EP-48 [3] D. HOT EPDM
EP-55 [3] D. HOT EPDM

[1] Only products bearing the NSF Mark are Certified.
[3] EP-48 and EP-55 compounds are molded into other gasket and o-ring seals. Certified for a
    maximum surface area to volume ratio of 2 sq. in./L.



 
Angst+Pfister AG 
Thurgauerstrasse 66
CH-8052 Zurich 
Switzerland 
41 1 306 61 11

Facility : # 1 Italy

Joining and Sealing Materials

    Water Water
    Contact Contact
Trade Designation Size Temp Material

O-Rings
EPDM 75.5/KW75F [1] C. HOT EPDM
HITEC® NBR 70.10-02 (NBR 70.5/P5F)[2] [1] C. HOT NBR

[1] Certified for a maximum surface area to volume ratio of 2.0 sq. in./L.
[2] This product has also been evaluated for use in Mechanical Plumbing Device applications
    with a maximum use restriction of 0.2 sq. in./L.



 
Anvil International, LLC 
2 Holland Way
Exeter, NH 03833 
United States 
603-418-2800

Facility : Yaphank, NY

Joining and Sealing Materials

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Lubricants[G]
Gruvlok Xtreme Lubricant™ >= 1/2" C. HOT SLC

[G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for
    “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state
    laws and the U.S. Safe Drinking Water Act.

    



 
Ar-Tex S.P.A. 
Via Rasetti 12
24060 Viadanica 
Italy 
390 35 928585

Facility : New Bedford, MA

Joining and Sealing Materials

    Water Water
    Contact Contact
Trade Designation Size Temp Material

O-Rings[1]
M70004 [2] D. HOT EPDM

[1] This product has been evaluated for use in Mechanical Plumbing Device applications with
    a maximum use restriction of 2.0 sq. in./L.
[2] Certified for a maximum surface area to volume of 2.0 sq. in./L.


Facility : Viadanica, Italy

Joining and Sealing Materials

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Gasket/Sealing Materials
0477 NBR-70[3] [1] D. HOT NBR
4273 EPDM 70 [1] C. HOT EPDM

[1] Certified for a maximum surface area to volume ratio of 2.0 sq. in./L.
[3] This product has also been evaluated for use in Mechanical Plumbing Device applications
    with a maximum use restriction of 2.0 sq. in./L.

O-Rings
0470 NBR 70[2] [1] CLD 23 NBR
0477 NBR-70[3] [1] D. HOT NBR
4270 EPDM 70[3] [1] C. HOT EPDM
4273 EPDM 70 [1] C. HOT EPDM
4360 EPDM 60 [1] C. HOT EPDM

[1] Certified for a maximum surface area to volume ratio of 2.0 sq. in./L.
[2] This product has also been evaluated for use in Mechanical Plumbing Device applications
    with a maximum use restriction of 0.2 sq. in./L.
[3] This product has also been evaluated for use in Mechanical Plumbing Device applications
    with a maximum use restriction of 2.0 sq. in./L.



 
Arsan Kaucuk Plastik-Makina Sanayi Ve Ticaret A.S. 
Yukari Dudullu Org. San. Bölgesi
Nato Yolu No:35 , Umraniye 
34775 Istanbul 
Turkey 
90 216 365 8306
Visit this company's website

Facility : Istanbul, Turkey

Joining and Sealing Materials

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Gasket/Sealing Materials
H880133H [1] CLD 23 EPDM
H880333S [1] CLD 23 EPDM
H880251D [1] CLD 23 EPDM

[1] Certified for a maximum surface area to volume ratio of 2.0 sq. in./L.



 
AVK Gummi A/S 
Mosegaardsvej 1
DK-8670 Laasby 
Denmark 
45 86 95 13 11
Visit this company's website

Facility : Laasby, Denmark

Joining and Sealing Materials

    Water Water
    Contact Contact
Trade Designation Size Temp Material

O-Rings [G]
EIW-55 [1] CLD 23 EPDM

[1] Certified for a maximum surface area to volume ratio of 2 square inches per liter.
[G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for
    “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state
    laws and the U.S. Safe Drinking Water Act.

    



 
BASF Construction Chemicals 
23700 Chagrin Boulevard
Cleveland, OH 44122 
United States 
800-628-9990 
216-839-7000
Visit this company's website

Facility : Newark, CA

Joining and Sealing Materials

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Patching Materials
MasterSeal 590 [1] CLD 23 CMNT
Waterplug [1] CLD 23 CMNT

[1] Certified for use as patching material up to 10% if the surface area in tanks 50 gallons
    or greater.


Facility : Streetsboro, OH

Joining and Sealing Materials

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Grouts
Masterflow 928 [1] CLD 23 CMNT
Masterflow® 1515 Pipesaver[2] [3] CLD 23 CMNT

[1] Certified for 25% of a tank 100 gallons and greater.
[2] Pipelines containing grout used to adhere repair lines must undergo a flush of 3-5
    gallons/minute for 1 hour prior to being placed back into service.
[3] Certified for use as a grout to adhere in-situ repair liners to potable water pipelines
    4" - 12" in diameter.  Certified for a maximum surface area to volume ratio of 0.3 sq.
    in./L.

Patching Materials
MasterEmaco S 210 SP [4] CLD 23 CMNT
MasterEmaco S 211 SP [4] CLD 23 CMNT
ShotPatch 21 [4] CLD 23 CMNT
ShotPatch 21F [4] CLD 23 CMNT

[4] Certified for use with pipes 48" and greater or tanks 3000 gallons and greater.


Facility : Bristol, PA

Joining and Sealing Materials

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Patching Materials
MasterSeal 590 2000 gal. CLD 23 CMNT
Waterplug 2000 gal. CLD 23 CMNT


Facility : Houston, TX

Joining and Sealing Materials

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Patching Materials
Emaco S88 CI [1] CLD 23 CMNT
MasterEmaco S 210 SP [2] CLD 23 CMNT
MasterEmaco S 211 SP [2] CLD 23 CMNT
MasterEmaco S 488 Cl [1] CLD 23 CMNT
Masterflow 928 [3] CLD 23 CMNT
ShotPatch 21 [2] CLD 23 CMNT
ShotPatch 21F [2] CLD 23 CMNT

[1] Certified for 10% coverage of a tank 200,000 gallons or greater and 5% of a pipe 84
    inches or greater.
[2] Certified for use with pipes 20" and greater or tanks 1,000 gallons and greater.
[3] Certified for 25% of a 100 gallon tank and greater.



 
Bayer MaterialScience 
100 Bayer Road
Pittsburgh, PA 15205-9741 
United States 
412-777-3491
Visit this company's website

Facility : New Martinsville, WV

Joining and Sealing Materials

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Grouts
BaySystems 486Star-3 (N-61) / Mondur MR Light (N-61) [1] CLD 23 PUR
BaySystems 486Star-4 (N-61) / Mondur MR Light (N-61) [1] CLD 23 PUR
BaySystems 486Star-6 (N-61) / Mondur MR Light (N-61) [1] CLD 23 PUR

[1] Certified for a maximum of 0.02 sq. in./L. in pipes or tanks.



 
Belzona Inc. 
2000 N.W. 88 Court
Miami, FL 33172 
United States 
305-594-4994
Visit this company's website

Facility : Harrogate, N. Yorks, United Kingdom

Joining and Sealing Materials

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Sealants
Belzona 1221 (Super E-Metal)[3] [1] [2] CLD 23 MM

[1] For tank and distribution line use: No greater than 10% of surface area.
[2] For residential use: No greater than 150 sq. in. per residence.
[3] Certified product is marked (NSF Grade).



 
Bernzomatic 
One Bernzomatic Drive
Medina, NY 14103 
United States 
585-798-4949

Facility : Winston-Salem, NC

Joining and Sealing Materials

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Brazing/Solders/Fluxes[G]
BernzOmatic® Lead-Free Silver Bearing Solder >= 1/2" C. HOT SLDR

[G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for
    “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state
    laws and the U.S. Safe Drinking Water Act.

    



 
Best Ring Industrial Corp. 
No. 36 Lane 148, Li De Street
Chung Ho City 
235 Taipei 
Taiwan 
886 2 3234 9977
Visit this company's website

Facility : Haicang Xiamen, China

Joining and Sealing Materials

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Gasket/Sealing Materials
E6088[2] [1] C. HOT EPDM
E7088 [1] C. HOT EPDM
E8088[2] [1] C. HOT EPDM
EEP0708 OP[3] [1] C. HOT EPDM
EP0B9001P[2] [1] C. HOT EPDM
EP0E7001P-WRC[4] [5] C. HOT EPDM
EP6566[2] [1] C. HOT EPDM
EP70+/-5 Purple EP7E7001PF [1] CLD 23 EPDM
EP8055PC[6] [1] C. HOT EPDM
N5066 [7] C. HOT NBR
N6088[2] [7] C. HOT NBR
N7088 [7] C. HOT NBR
N7588 [7] C. HOT NBR
N8088[2] [7] C. HOT NBR
S6001N[9] [8] C. HOT SLC
S7001N[9] [8] C. HOT SLC
S8001N[9] [8] C. HOT SLC
SIL40 +/-5 S4001[9] [8] C. HOT SLC

[1] Certified for a maximum surface area to volume ratio of 2.0 sq. in./L.
[2] This product has also been evaluated for use in Mechanical Plumbing Device applications
    with a maximum surface area to volume ratio of 0.2 sq. in./L.
[3] This product has also been evaluated for use in Mechanical Plumbing Device applications
    with a maximum use restriction of 1.1 sq. in./L.
[4] This product has also been evaluated for use in Mechanical Plumbing Device applications
    with a maximum use restriction of 0.1 sq. in./L.
[5] Certified for a maximum surface area to volume ratio of 1.0 sq. in./L.
[6] This product has also been evaluated for use in Mechanical Plumbing Device applications
    with a maximum surface area to volume ratio of 0.8 sq. in./L.
[7] Certified for a maximum surface area to volume ratio of 1.6 sq. in./L.
[8] Certified for a maximum surface area to volume ratio of 1.5 sq. in./L.
[9] This product has also been evaluated for use in Mechanical Plumbing Device applications
    with a maximum use restriction of 0.15 sq. in./L.

O-Rings
EEP0708 OP[3] [1] C. HOT MLTPL
EP0B9001P[10] [1] C. HOT EPDM
EP0E7001P-WRC[4] [5] C. HOT EPDM
EP70+/-5 Purple EP7E7001PF [1] CLD 23 EPDM
EP8055PC[6] [1] C. HOT EPDM

[1] Certified for a maximum surface area to volume ratio of 2.0 sq. in./L.
[3] This product has also been evaluated for use in Mechanical Plumbing Device applications
    with a maximum use restriction of 1.1 sq. in./L.
[4] This product has also been evaluated for use in Mechanical Plumbing Device applications
    with a maximum use restriction of 0.1 sq. in./L.
[5] Certified for a maximum surface area to volume ratio of 1.0 sq. in./L.
[6] This product has also been evaluated for use in Mechanical Plumbing Device applications
    with a maximum surface area to volume ratio of 0.8 sq. in./L.
[10] Certified for a maximum surface area to volume ratio of 0.4 sq. in./L.



 
Best Ring Industrial Corp. 
No. 36, Lane 148, Li De Street
Chung Ho District, New Taipei City 235 
Taiwan 
886 2 3234 9977

Facility : Changhua Hsien, Taiwan

Joining and Sealing Materials

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Gasket/Sealing Materials
EP0E7188PWRC [1] C. HOT EPDM

[1] Certified for a maximum surface area to volume ratio of 2.0 sq. in./L.



 
Best Ring Technology Co., Ltd. 
No. 558 Xiexin Road
Fengxian, Shanghai 
China 
86 21 68127553
Visit this company's website

Facility : Shanghai, China

Joining and Sealing Materials

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Gasket/Sealing Materials
LSB-Gasket [1] C. HOT EPDM
LSB-ORing [1] C. HOT EPDM
LSB-URing [1] C. HOT EPDM
LSB-VRing [1] C. HOT EPDM
LSB-XRing [1] C. HOT EPDM
LSB-YRing [1] C. HOT EPDM

[1] Certified for a maximum surface area to volume ratio of 2.0 sq. in./L.

O-Rings
LSB-Gasket [1] C. HOT EPDM
LSB-ORing [1] C. HOT EPDM
LSB-URing [1] C. HOT EPDM
LSB-VRing [1] C. HOT EPDM
LSB-XRing [1] C. HOT EPDM
LSB-YRing [1] C. HOT EPDM

[1] Certified for a maximum surface area to volume ratio of 2.0 sq. in./L.



 
bioCANlubricants Ltd. 
100 Wilkinson Road
Unit 12 
Brampton, ON L6T 4Y9 
Canada 
416-884-1635

Facility : Brampton, Ontario, Canada

Joining and Sealing Materials

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Lubricants
BioCANlubricants Pipe Lubricant - Paste >= 1/2" CLD 23 LUB
IPEX PVC PIPE LUBRICANT PASTE >= 1/2" CLD 23 LUB
NEXT POLYMERS PVC PIPE LUBRICANT PASTE >= 1/2" CLD 23 LUB
ROYAL PIPE LUBRICANT >=1/2" CLD 23 LUB



 
Bode GmbH 
Kirchweg 114
D-24558 Henstedt-Ulzburg 
Germany 
49 4193 982 0
Visit this company's website

Facility : Henstedt-Ulzburg, Germany

Joining and Sealing Materials

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Gasket/Sealing Materials
EPDM B1-4771[1] [2] C. HOT EPDM

[1] This product has also been evaluated for use in Mechanical Plumbing Device applications
    with a maximum use restriction of 2.0 sq.in./L.
[2] Certified for a maximum surface area to volume ratio of 2.0 sq.in./L.

O-Rings
EPDM B1-4771[1] [2] C. HOT EPDM

[1] This product has also been evaluated for use in Mechanical Plumbing Device applications
    with a maximum use restriction of 2.0 sq.in./L.
[2] Certified for a maximum surface area to volume ratio of 2.0 sq.in./L.


Facility : C Italy

Joining and Sealing Materials

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Gasket/Sealing Materials
EPDM B1-4771[2] [1] C. HOT EPDM

[1] Certified for a maximum surface area to volume ratio of 2.0 sq.in./L.
[2] This product has also been evaluated for use in Mechanical Plumbing Device applications
    with a maximum use restriction of 2.0 sq.in./L.

O-Rings
EPDM B1-4771[2] [1] C. HOT EPDM

[1] Certified for a maximum surface area to volume ratio of 2.0 sq.in./L.
[2] This product has also been evaluated for use in Mechanical Plumbing Device applications
    with a maximum use restriction of 2.0 sq.in./L.



 
Bode GmbH 
Kirchweg 114
24558 Henstedt-Ulzburg 
Germany 
49 4193 982 0

Facility : A China

Joining and Sealing Materials

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Gasket/Sealing Materials
B1-4771[1] [2] [3] C. HOT EPDM
B1-4772[1] [3] C. HOT EPDM
B1-4773[1] [3] C. HOT EPDM

[1] This product has also been evaluated for use in Mechanical Plumbing Device applications
    with a maximum use restriction of 2.0 sq. in./L.
[2] This product has also been evaluated with the use of a lubricant, Triboskin 88.
[3] Certified for a maximum surface area to volume ratio of 2.0 sq. in./L.

O-Rings
B1-4771[1] [2] [3] C. HOT EPDM
B1-4772[1] [3] C. HOT EPDM
B1-4773[1] [3] C. HOT EPDM

[1] This product has also been evaluated for use in Mechanical Plumbing Device applications
    with a maximum use restriction of 2.0 sq. in./L.
[2] This product has also been evaluated with the use of a lubricant, Triboskin 88.
[3] Certified for a maximum surface area to volume ratio of 2.0 sq. in./L.


Facility : B China

Joining and Sealing Materials

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Gasket/Sealing Materials
B1-4771[1] [2] C. HOT EPDM

[1] This product has also been evaluated for use in Mechanical Plumbing Device applications
    with a maximum use restriction of 2.0 sq. in./L.
[2] Certified for a maximum surface area to volume ratio of 2.0 sq. in./L.

O-Rings
B1-4771[1] [2] C. HOT EPDM

[1] This product has also been evaluated for use in Mechanical Plumbing Device applications
    with a maximum use restriction of 2.0 sq. in./L.
[2] Certified for a maximum surface area to volume ratio of 2.0 sq. in./L.



 
Bode Trading (Xiamen) Co., Ltd. 
8C, Xiang Yu Buliding
Xiang Yu F.T.Z. 
Xiamen, Fujian Province 361000 
China 
86 (0) 592 6021 160

Facility : A China

Joining and Sealing Materials

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Gasket/Sealing Materials
70EP101p[1] [2] [3] C. HOT EPDM
70EP111p[4] [3] C. HOT EPDM
70EP124p[1] [3] C. HOT EPDM

[1] This product has also been evaluated for use in Mechanical Plumbing Device applications
    with a maximum use restriction of 2.0 sq. in./L.
[2] This product has also been evaluated with the use of a lubricant, Mountfit SAGB 4025.
[3] Certified for a maximum surface area to volume ratio of 2.0 sq. in./L.
[4] This product has also been evaluated for use in Mechanical Plumbing Device applications
    with a maximum use restriction of 1.5 sq. in./L.

O-Rings
70EP101p[1] [2] [3] C. HOT EPDM
70EP111p[4] [3] C. HOT EPDM
70EP124p[1] [3] C. HOT EPDM

[1] This product has also been evaluated for use in Mechanical Plumbing Device applications
    with a maximum use restriction of 2.0 sq. in./L.
[2] This product has also been evaluated with the use of a lubricant, Mountfit SAGB 4025.
[3] Certified for a maximum surface area to volume ratio of 2.0 sq. in./L.
[4] This product has also been evaluated for use in Mechanical Plumbing Device applications
    with a maximum use restriction of 1.5 sq. in./L.


Facility : B China

Joining and Sealing Materials

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Gasket/Sealing Materials
70EP101p[1] [2] C. HOT EPDM
70EP111p[3] [4] [2] C. HOT EPDM

[1] This product has also been evaluated for use in Mechanical Plumbing Device applications
    with a maximum use restriction of 2.0 sq. in./L.
[2] Certified for a maximum surface area to volume ratio of 2.0 sq. in./L.
[3] This product has also been evaluated for use in Mechanical Plumbing Device applications
    with a maximum use restriction of 1.5 sq. in./L.
[4] This product has also been evaluated with the use of a lubricant, Mountfit SAGB 4025.

O-Rings
70EP101p[1] [2] C. HOT EPDM
70EP111p[3] [4] [2] C. HOT EPDM

[1] This product has also been evaluated for use in Mechanical Plumbing Device applications
    with a maximum use restriction of 2.0 sq. in./L.
[2] Certified for a maximum surface area to volume ratio of 2.0 sq. in./L.
[3] This product has also been evaluated for use in Mechanical Plumbing Device applications
    with a maximum use restriction of 1.5 sq. in./L.
[4] This product has also been evaluated with the use of a lubricant, Mountfit SAGB 4025.


Facility : E China

Joining and Sealing Materials

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Gasket/Sealing Materials
70EP111p[1] [2] C. HOT EPDM
70EP124p[3] [4] C. HOT EPDM
70EP133p[5] [4] C. HOT EPDM

[1] This product has also been evaluated for use in Mechanical Plumbing Device applications
    with a maximum use restriction of 1.5 sq. in./L.
[2] Certified for a maximum surface area to volume ratio of 1.1 sq. in./L.
[3] This product has also been evaluated for use in Mechanical Plumbing Device applications
    with a maximum use restriction of 0.9 sq. in./L.
[4] Certified for a maximum surface area to volume ratio of 2.0 sq. in./L.
[5] This product has also been evaluated for use in Mechanical Plumbing Device applications
    with a maximum use restriction of 2 sq. in./L.

O-Rings
70EP111p[1] [2] C. HOT EPDM
70EP124p[3] [4] C. HOT EPDM
70EP133p[5] [4] C. HOT EPDM

[1] This product has also been evaluated for use in Mechanical Plumbing Device applications
    with a maximum use restriction of 1.5 sq. in./L.
[2] Certified for a maximum surface area to volume ratio of 1.1 sq. in./L.
[3] This product has also been evaluated for use in Mechanical Plumbing Device applications
    with a maximum use restriction of 0.9 sq. in./L.
[4] Certified for a maximum surface area to volume ratio of 2.0 sq. in./L.
[5] This product has also been evaluated for use in Mechanical Plumbing Device applications
    with a maximum use restriction of 2 sq. in./L.



 
BodeDynamic GmbH 
Kirchweg 114
24558 Henstedt-Ulzburg 
Germany 
49 419 3982 0
Visit this company's website

Facility : A China

Joining and Sealing Materials

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Gasket/Sealing Materials
70EP101p[1] [2] C. HOT EPDM
70EP111p[3] [2] C. HOT EPDM
70EP124p[1] [2] C. HOT EPDM

[1] This product has also been evaluated for use in Mechanical Plumbing Device applications
    with a maximum use restriction of 2.0 sq. in./L.
[2] Certified for a maximum surface area to volume ratio of 2.0 sq. in./L.
[3] This product has also been evaluated for use in Mechanical Plumbing Device applications
    with a maximum use restriction of 1.5 sq. in./L.

O-Rings
70EP101p[1] [2] C. HOT EPDM
70EP111p[3] [2] C. HOT EPDM
70EP124p[1] [2] C. HOT EPDM

[1] This product has also been evaluated for use in Mechanical Plumbing Device applications
    with a maximum use restriction of 2.0 sq. in./L.
[2] Certified for a maximum surface area to volume ratio of 2.0 sq. in./L.
[3] This product has also been evaluated for use in Mechanical Plumbing Device applications
    with a maximum use restriction of 1.5 sq. in./L.


Facility : B China

Joining and Sealing Materials

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Gasket/Sealing Materials
70EP101p[1] [2] C. HOT EPDM
70EP111p[3] [4] [2] C. HOT EPDM

[1] This product has also been evaluated for use in Mechanical Plumbing Device applications
    with a maximum use restriction of 2.0 sq. in./L.
[2] Certified for a maximum surface area to volume ratio of 2.0 sq. in./L.
[3] This product has also been evaluated for use in Mechanical Plumbing Device applications
    with a maximum use restriction of 1.5 sq. in./L.
[4] This product has also been evaluated with the use of a lubricant, Mountfit SAGB 4025.

O-Rings
70EP101p[1] [2] C. HOT EPDM
70EP111p[3] [4] [2] C. HOT EPDM

[1] This product has also been evaluated for use in Mechanical Plumbing Device applications
    with a maximum use restriction of 2.0 sq. in./L.
[2] Certified for a maximum surface area to volume ratio of 2.0 sq. in./L.
[3] This product has also been evaluated for use in Mechanical Plumbing Device applications
    with a maximum use restriction of 1.5 sq. in./L.
[4] This product has also been evaluated with the use of a lubricant, Mountfit SAGB 4025.


Facility : E China

Joining and Sealing Materials

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Gasket/Sealing Materials
70EP111p[4] [5] C. HOT EPDM
70EP124p[2] [1] C. HOT EPDM
70EP133P[3] [1] C. HOT EPDM

[1] Certified for a maximum surface area to volume ratio of 2.0 sq. in./L.
[2] This product has also been evaluated for use in Mechanical Plumbing Device applications
    with a maximum use restriction of 0.9 sq. in./L.
[3] This product has also been evaluated for use in Mechanical Plumbing Device applications
    with a maximum use restriction of 2 sq. in./L.
[4] This product has also been evaluated for use in Mechanical Plumbing Device applications
    with a maximum use restriction of 1.5 sq. in./L.
[5] Certified for a maximum surface area to volume ratio of 1.1 sq. in./L.

O-Rings
70EP111p[4] [5] C. HOT EPDM
70EP124p[2] [1] C. HOT EPDM
70EP133P[3] [1] C. HOT EPDM

[1] Certified for a maximum surface area to volume ratio of 2.0 sq. in./L.
[2] This product has also been evaluated for use in Mechanical Plumbing Device applications
    with a maximum use restriction of 0.9 sq. in./L.
[3] This product has also been evaluated for use in Mechanical Plumbing Device applications
    with a maximum use restriction of 2 sq. in./L.
[4] This product has also been evaluated for use in Mechanical Plumbing Device applications
    with a maximum use restriction of 1.5 sq. in./L.
[5] Certified for a maximum surface area to volume ratio of 1.1 sq. in./L.


Facility : Plant F

Joining and Sealing Materials

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Gasket/Sealing Materials[1]
70EP101p [2] C. HOT EPDM

[1] This product has also been evaluated for use in Mechanical Plumbing Device applications
    with a maximum use restriction of 2.0 sq. in./L.
[2] Certified for a maximum surface area to volume ratio of 2.0 sq. in./L.

O-Rings[1]
70EP101p [2] C. HOT EPDM

[1] This product has also been evaluated for use in Mechanical Plumbing Device applications
    with a maximum use restriction of 2.0 sq. in./L.
[2] Certified for a maximum surface area to volume ratio of 2.0 sq. in./L.



 
Boshart Industries, Inc. 
25 Whaley Avenue
P.O. Box 310 
Milverton, ON N0K 1M0 
Canada 
519-595-4444

Facility : # 1 USA

Joining and Sealing Materials

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Sealants
Gray Magic Thread Compound >= 1/2" C. HOT NA



 
Burke Industries, Inc. 
2250 South Tenth Street
San Jose, CA 95112-4197 
United States 
408-297-3500

Facility : San Jose, CA

Joining and Sealing Materials

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Gasket/Sealing Materials
Burke Rubber #4104[1] 2.0 sq. in./L CLD 23 EPDM
Burke Rubber #6154 2.0 sq. in./L CLD 23 NBR
Burke Rubber #6163 2.0 sq. in./L CLD 23 NBR
Burke Rubber #6168 2.0 sq. in./L CLD 23 NBR
HXA 4454 2.0 sq. in./L CLD 23 NBR

[1] Certified for a maximum surface area to volume ratio of 2.0 sq. in./L.  Also Certified
    for 24" x 18" tapered valve sleeves/liners.



 
C.I. Kasei Co., Ltd. 
18-1 Kyobashi 1-chome
Tokyo 104-8321 
Japan 
81 3 3535 4568
Visit this company's website

Facility : Tochigi Prefecture, Japan

Joining and Sealing Materials

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Gasket/Sealing Materials
Hydrotite CJ[2] [1] CLD 23 CR

[1] Certified for a maximum surface area to volume ratio of 1.2 sq. in./L.
[2] This product has been evaluated for chloroprene rubber material only and does not
    include adhesives, lubricants, or sealants.



 
Canada Metal (Eastern)(2010) Ltd. 
8271 Rue LaFrenaie
St. Leonard, QC H1P 2B1 
Canada 
514-327-2011

Facility : # 1 Canada

Joining and Sealing Materials

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Brazing/Solders/Fluxes[G]
Canada Metal Soldering Paste 50 >= 1/2" C. HOT SLDR

[G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for
    “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state
    laws and the U.S. Safe Drinking Water Act.

    



 
Carl Bechem GmbH 
Weststrasse 120
D-58089 Hagen 
Germany 
49 2331 935 0

Facility : Hagen, Germany

Joining and Sealing Materials

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Lubricants
Berulub FO 34 [1] D. HOT LUB
Berulub FU 5 >= 1/2" D. HOT LUB
Berusil CDG 352 [1] D. HOT LUB
Berusoft 30 [2] D. HOT LUB

[1] Certified for a maximum surface area to volume ratio of 7.27 sq. in./L.
[2] Certified for use with 1/2" pipe and greater.


Facility : Mieste, Germany

Joining and Sealing Materials

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Lubricants
Berulub Sihaf 1 [1] D. HOT LUB
Berulub Sihaf 2[1] >= 1/2" D. HOT PTFE

[1] Certified for a maximum surface area to volume of 7.27 sq. in./L.



 
Chang Horing Rubber Co., Ltd. 
No. 38, Lu-Gong South 3 Road
Lu-Kang Town, Changhua Hsien 505 
Taiwan 
886 4781 0868
Visit this company's website

Facility : Changhua Hsien, Taiwan

Joining and Sealing Materials

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Gasket/Sealing Materials
EP01961PWRC[G] [1] C. HOT EPDM
EP02971PWRC [1] C. HOT EPDM
NB03973PWRC [1] C. HOT NBR

[1] Certified for a maximum surface area to volume ratio of 2.0 sq. in./L.
[G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for
    “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state
    laws and the U.S. Safe Drinking Water Act.

    



 
Chemofast Anchoring GmbH 
Hanns-Martin-Schleyer-Strasse 23
D-47877 Willich 
Germany 
49 2154 8123 0
Visit this company's website

Facility : Willich, Germany

Joining and Sealing Materials

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Adhesives
ALVK [1] D. HOT VE
C-RE 385 [1] D. HOT EPOXY
STVK [1] D. HOT VE

[1] Certified for use as an anchoring adhesive for installing thread rods (less than or
    equal to 1.3 inches in diameter) in concrete or masonry for water treatment applications.



 
Chi-Yih Enterprises Co., Ltd. 
No. 93 Lane 245 Sec 3, Sha-Tien Road
Tatu Taichung 
Taiwan 
886 42 6996802

Facility : Baoan Shenzhen, China

Joining and Sealing Materials

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Gasket/Sealing Materials[1]
CY-E36099-A[2] 2.0 sq. in./L C. HOT EPDM
CY-E37072-A[2] 2.0 sq. in./L C. HOT EPDM
CY-E38012-A[3] 2.0 sq. in./L C. HOT EPDM

[1] Only products bearing the NSF Mark on the product, product packaging, and/or
    documentation shipped with the product are Certified.
[2] This product has also been evaluated for use in Mechanical Plumbing Device applications
    with a maximum surface area to volume ratio of 0.3 sq.in./L.
[3] This product has also been evaluated for use in Mechanical Plumbing Device applications
    with a maximum surface area to volume ratio of 0.2 sq. in./L.


Facility : Tatu Taichung, Taiwan

Joining and Sealing Materials

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Gasket/Sealing Materials
CY-E36099-A [2] C. HOT EPDM
CY-E37072-A [2] C. HOT EPDM
CY-E38012-A [2] C. HOT EPDM
CY-N66020-A[3] [1] C. HOT NBR
CY-N67015-A[3] [1] C. HOT NBR
CY-N68049-A[3] [1] C. HOT NBR

[1] Certified for a maximum surface area to volume ratio of 0.5 sq. in./L.
[2] Certified for a maximum surface area to volume ratio of 2.0 sq. in./L.
[3] This product has also been evaluated for use in Mechanical Plumbing Device applications
    with a maximum use restriction of 0.1 sq. in./L.

O-Rings
CY-E36099-A [2] C. HOT EPDM
CY-E37072-A [2] C. HOT EPDM
CY-E38012-A [2] C. HOT EPDM
CY-N66020-A[3] [1] C. HOT NBR
CY-N67015-A[3] [1] C. HOT NBR
CY-N68049-A[3] [1] C. HOT NBR

[1] Certified for a maximum surface area to volume ratio of 0.5 sq. in./L.
[2] Certified for a maximum surface area to volume ratio of 2.0 sq. in./L.
[3] This product has also been evaluated for use in Mechanical Plumbing Device applications
    with a maximum use restriction of 0.1 sq. in./L.



 
CITGO Petroleum Corporation 
1293 Eldridge Parkway
Houston, TX 77077 
United States 
800-248-4684 
832-486-4071
Visit this company's website

Facility : Hammond, IN

Joining and Sealing Materials

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Lubricants
Clarion Food Machinery A/W Oil 32 [1] C. HOT LUB
Clarion Food Machinery A/W Oil 68 [1] C. HOT LUB
Clarion Food Machinery Gear Oil 220 [1] C. HOT LUB
Clarion® Food Grade White Mineral Oil 200 [1] C. HOT LUB
Clarion® Food Grade White Mineral Oil 350 [1] C. HOT LUB

[1] Certified for a maximum surface area to volume ratio of 0.05 sq. in./L.

NOTE: Only products bearing the NSF Mark on the product, product packaging, and/or
      documentation shipped with the product are Certified.

Facility : Oklahoma City, OK

Joining and Sealing Materials

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Lubricants
Clarion Food Machinery Grease No. 2 [1] C. HOT LUB
Clarion Food Machinery HT EP Grease No. 2 [1] C. HOT LUB

[1] Certified for a maximum surface area to volume ratio of 0.05 sq. in./L.

NOTE: Only products bearing the NSF Mark on the product, product packaging, and/or
      documentation shipped with the product are Certified.


 
Clearco Products Co., Inc. 
3430 Progress Drive
Suite G 
Bensalem, PA 19020 
United States 
800-533-5823 
215-639-2640

Facility : # 1 USA

Joining and Sealing Materials

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Lubricants
Silicone Grease 2012 >= 1/2" C. HOT SLC



 
Columbia Engineered Rubber 
2501 Thunderhawk Court
Dayton, OH 45414 
United States 
800-227-3539 
937-890-7464
Visit this company's website

Facility : Vandalia, OH

Joining and Sealing Materials

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Gasket/Sealing Materials
Hydrorite® E702[1] [2] C. HOT EPDM
Hydrorite® E702-PolyCT™ 0392[1] [2] C. HOT EPDM
Hydrorite® E703[1] [2] C. HOT EPDM
Hydrorite® E703-PolyCT™ 0392[1] [2] C. HOT EPDM
Hydrorite® E706[1] [2] C. HOT EPDM
S60-8191[3] [2] C. HOT SLC
S70-8191[3] [2] C. HOT SLC

[1] This product has also been evaluated for use in Mechanical Plumbing Device applications
    with a maximum use restriction of 0.8 sq. in./L.
[2] Certified for a maximum surface area to volume ratio of 2.0 sq. in./L.
[3] This product has also been evaluated for use in Mechanical Plumbing Device applications
    with a maximum use restriction of 2.0 sq. in./L.

O-Rings
Hydrorite® E702[1] [2] C. HOT EPDM
Hydrorite® E702-PolyCT™ 0392[1] [2] C. HOT EPDM
Hydrorite® E703[1] [2] C. HOT EPDM
Hydrorite® E703-PolyCT™ 0392[1] [2] C. HOT EPDM
Hydrorite® E706[1] [2] C. HOT EPDM
S60-8191[3] [2] C. HOT SLC
S70-8191[3] [2] C. HOT SLC

[1] This product has also been evaluated for use in Mechanical Plumbing Device applications
    with a maximum use restriction of 0.8 sq. in./L.
[2] Certified for a maximum surface area to volume ratio of 2.0 sq. in./L.
[3] This product has also been evaluated for use in Mechanical Plumbing Device applications
    with a maximum use restriction of 2.0 sq. in./L.



 
Columbia Engineered Rubber 
2501 Thunderhawk Court
Dayton, OH 45414 
United States 
800-227-3539 
937-890-7464

Facility : # 1 Shanghai, China

Joining and Sealing Materials

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Gasket/Sealing Materials
E620 [1] C. HOT EPDM
E721 [2] C. HOT EPDM
E722[4] [2] C. HOT EPDM
E723 [2] C. HOT EPDM
E724[4] [2] C. HOT EPDM
E725 [1] C. HOT EPDM
E726 [1] C. HOT EPDM
E820[4] [2] C. HOT EPDM
E821 [1] C. HOT EPDM
FBR720 [2] C. HOT FE
N721 [2] C. HOT NBR
N723 [2] C. HOT NBR
N820 [2] C. HOT NBR
N920 [2] C. HOT NBR
S320[3] [2] C. HOT SLC
S720[3] [2] C. HOT SLC
SG620[3] [2] C. HOT SLC

[1] Certified for a maximum surface area to volume ratio of 1 sq. in./L.
[2] Certified for a maximum surface area to volume ratio of 2.0 sq. in./L.
[3] This product has also been evaluated for use in Mechanical Plumbing Device applications
    with a maximum surface area to volume ratio of 2.0 sq. in./L.
[4] This product has also been evaluated for use in Mechanical Plumbing Device applications
    with a maximum use restriction of 0.9 sq. in./L.



 
Concrete Sealants, Inc. 
P.O. Box 176
New Carlisle, OH 45344 
United States 
800-332-7325 
937-845-8776
Visit this company's website

Facility : Tipp City, OH

Joining and Sealing Materials

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Lubricants
ConLube CS-2000 >= 1/2" D. HOT LUB

Sealants
CS-231 >= 1/2" D. HOT MLTPL
CS-231-47B >= 1/2" D. HOT MLTPL
CS-235 >= 1/2" D. HOT MLTPL
CS-238 >= 1/2" D. HOT MLTPL
Conclay Seal >= 1/2" D. HOT MLTPL
Conseal CS-665 >= 1/2" D. HOT MLTPL
SuperSwell 47B >= 1/2" D. HOT MLTPL
WAM101 >= 1/2" D. HOT MLTPL



 
Corkjoint SDN BHD 
Lot E/23117 Jalan 5/32A
Off Batu 6 1/2 Jalan, Kuala Lumpur 52100 
Malaysia 
60 3 6250 9630

Facility : Tipp City, OH

Joining and Sealing Materials

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Sealants
SuperSwell 47B >= 1/2" D. HOT MLTPL



 
Custom Rubber Corp. 
1274 East 55th Street
Cleveland, OH 44103 
United States 
216-391-2928
Visit this company's website

Facility : Cleveland, OH

Joining and Sealing Materials

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Gasket/Sealing Materials
CRCE1000 Rev. B [1] CLD 23 EPDM

[1] Certified for a maximum surface area to volume ratio of 2.0 sq. in./L.

O-Rings
CRCE1000 Rev. B [1] CLD 23 EPDM

[1] Certified for a maximum surface area to volume ratio of 2.0 sq. in./L.



 
Danco, Inc. 
2727 Chemsearch Boulevard
Irving, TX 75062 
United States 
972-438-0990

Facility : # 1 USA

Joining and Sealing Materials

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Lubricants
9D00088693 >= 1/2" C. HOT SLC
9D0080360A >= 1/2" C. HOT SLC
9DA080360A >= 1/2" C. HOT SLC
9DD0088693 >= 1/2" C. HOT SLC
9DD080360A >= 1/2" C. HOT SLC



 
Dichtomatik Americas LP 
1087 Park Place
Shakopee, MN 55379 
United States 
952-894-8400

Facility : # 2 China

Joining and Sealing Materials

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Gasket/Sealing Materials
E01-400-70 [2] C. HOT EPDM
N01-400-70 [1] C. HOT NBR

[1] Certified for a maximum surface area to volume ratio of 1.6 sq. in./L.
[2] Certified for a maximum surface area to volume ratio of 2.0 sq. in./L.



 
Dow Corning Corporation 
P.O. Box 994
Mail No. C03101 
Midland, MI 48686-0994 
United States 
989-496-4000

Facility : Elizabethtown, KY

Joining and Sealing Materials

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Sealants
Dow Corning® 732 Multipurpose - Aluminum [1] C. HOT SLC
Dow Corning® 732 Multipurpose - Black [1] C. HOT SLC
Dow Corning® 732 Multipurpose - Bronze [1] C. HOT SLC
Dow Corning® 732 Multipurpose - Clear [1] C. HOT SLC
Dow Corning® 732 Multipurpose - White [1] C. HOT SLC
Dow Corning® 748 Non-Corrosive Sealant [2] C. HOT SLC
Dow Corning® Linha Branca Tipo [1] C. HOT SLC

[1] Certified for a maximum surface area to volume ratio of 14.5 sq. in./L.
[2] Certified for a maximum surface area to volume ratio of 0.4 sq. in./L.


Facility : Greensboro, NC

Joining and Sealing Materials

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Lubricants
Dow Corning® 111 Valve Lubricant & Sealant [1] C. HOT SLC
Dow Corning® 4 Electrical Insulating Compound [1] C. HOT SLC
Dow Corning® 7 Release Compound [1] C. HOT SLC
Dow Corning® High Vacuum Grease [1] C. HOT SLC
MOLYKOTE 111 Compound [1] C. HOT SLC

[1] Certified for a maximum surface area to volume ratio of 40 sq. in./L.

Sealants
Dow Corning® 732 Multipurpose - Aluminum [2] C. HOT SLC
Dow Corning® 732 Multipurpose - Black [2] C. HOT SLC
Dow Corning® 732 Multipurpose - Clear [2] C. HOT SLC
Dow Corning® 732 Multipurpose - White [2] C. HOT SLC
Dow Corning® 748 Non-Corrosive Sealant [3] C. HOT SLC
Dow Corning® HM-2500 Assembly Sealant [2] C. HOT SLC
Dow Corning® HM-2510 Assembly Sealant [2] C. HOT SLC
Dow Corning® HM-2515 Assembly Sealant [2] C. HOT SLC
Dow Corning® HM-2520 Assembly Sealant [2] C. HOT SLC

[2] Certified for a maximum surface area to volume ratio of 14.5 sq. in./L.
[3] Certified for a maximum surface area to volume ratio of 0.4 sq. in./L.


Facility : Shanghai, China

Joining and Sealing Materials

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Lubricants
Dow Corning® 4 Electrical Insulating Compound [1] C. HOT LUB
Dow Corning® 7 Release Compound [1] C. HOT LUB
Molykote® 111 Compound [1] C. HOT LUB

[1] Certified for a maximum surface area to volume ratio of 40 sq. in./L.


Facility : Wiesbaden, Germany

Joining and Sealing Materials

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Lubricants
Molykote® 111 Compound [1] C. HOT LUB

[1] Certified for a maximum surface area to volume ratio of 40 sq. in./L.


Facility : Ashigara-Kamigun, Kanagawa, Japan

Joining and Sealing Materials

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Lubricants
MOLYKOTE® 7508 Valve Grease [1] C. HOT LUB

[1] Certified for a maximum surface area to volume ratio of 40 sq. in./L.



 
Duci SRL 
Via Monte Avaro 69
24060 Chiuduno (BG) 
Italy 
39 035 838294

Facility : Chiuduno (BG), Italy

Joining and Sealing Materials

    Water Water
    Contact Contact
Trade Designation Size Temp Material

O-Rings
EPDM 70 M534 [1] C. HOT EPDM

[1] Certified for a maximum surface area to volume ratio of 2.0 sq. in./L.



 
Durabla Canada Ltd 
293 University Avenue
Belleville, ON K8N 5B3 
Canada 
613-966-1442

Facility : Belleville, Ontario, Canada

Joining and Sealing Materials

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Gasket/Sealing Materials
D7910 [1] CLD 23 OTHER
Durlon 7910 [1] CLD 23 OTHER

[1] Certified for a maximum surface area to volume ratio of 0.8 sq. in./L.



 
Elastotech s.r.l. 
Via Provinciale, 92/94
24060 Castelli Calepio (BG) 
Italy 
39 035 44 96 000
Visit this company's website

Facility : Castelli Calepio (BG), Italy

Joining and Sealing Materials

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Gasket/Sealing Materials
ME0195/40[2] 20 sq. in./L C. HOT EPDM
ME0195/45[2] 20 sq. in./L C. HOT EPDM
ME0195/50[2] 20 sq. in./L C. HOT EPDM
ME0195/55[2] 20 sq. in./L C. HOT EPDM
ME0195/60[2] 20 sq. in./L C. HOT EPDM
ME0195/65[2] 20 sq. in./L C. HOT EPDM
ME0195/70[2] 20 sq. in./L C. HOT EPDM
ME0195/75[2] 20 sq. in./L C. HOT EPDM
ME0195/80[2] 20 sq. in./L C. HOT EPDM
ME0195/85[3] 20 sq. in./L C. HOT EPDM
ME0195/90[3] 20 sq. in./L C. HOT EPDM
ME0201/70V[3] 20 sq. in./L C. HOT FE
ME0940/40[2] 20 sq. in./L C. HOT EPDM
ME0940/45[2] 20 sq. in./L C. HOT EPDM
ME0940/50[2] 20 sq. in./L C. HOT EPDM
ME0940/55[2] 20 sq. in./L C. HOT EPDM
ME0940/60[2] 20 sq. in./L C. HOT EPDM
ME0940/65[2] 20 sq. in./L C. HOT EPDM
ME0940/70[2] 20 sq. in./L C. HOT EPDM
ME0940/75[2] 20 sq. in./L C. HOT EPDM
ME0940/80[2] 20 sq. in./L C. HOT EPDM
ME0940/85[3] 20 sq. in./L C. HOT EPDM
ME0940/90[3] 20 sq. in./L C. HOT EPDM
ME0996/40[2] 20 sq. in./L C. HOT NBR
ME0996/45[2] 20 sq. in./L C. HOT NBR
ME0996/50[2] 20 sq. in./L C. HOT NBR
ME0996/55[2] 20 sq. in./L C. HOT NBR
ME0996/60[2] 20 sq. in./L C. HOT NBR
ME0996/65[2] 20 sq. in./L C. HOT NBR
ME0996/70[2] 20 sq. in./L C. HOT NBR
ME0996/75[2] 20 sq. in./L C. HOT NBR
ME0996/80[2] 20 sq. in./L C. HOT NBR
ME0996/85[2] 20 sq. in./L C. HOT NBR
ME0996/90[2] 20 sq. in./L C. HOT NBR
ME2020/20[1] [2] 20 sq. in./L C. HOT SLC
ME2020/25[1] [2] 20 sq. in./L C. HOT SLC
ME2020/30[1] [2] 20 sq. in./L C. HOT SLC
ME2020/35[1] [2] 20 sq. in./L C. HOT SLC
ME2020/40[1] [2] 20 sq. in./L C. HOT SLC
ME2020/45[1] [2] 20 sq. in./L C. HOT SLC
ME2020/50[1] [2] 20 sq. in./L C. HOT SLC
ME2020/55[1] [2] 20 sq. in./L C. HOT SLC
ME2020/60[1] [2] 20 sq. in./L C. HOT SLC
ME2020/65[1] [2] 20 sq. in./L C. HOT SLC
ME2020/70[1] [2] 20 sq. in./L C. HOT SLC
ME2020/75[1] [2] 20 sq. in./L C. HOT SLC
ME2020/80[1] [2] 20 sq. in./L C. HOT SLC

[1] This product is Certified for the following colors:
    Transparent (no color), White, Black, Red, Red 3000, Blue, Yellow, Light green, Dark
    green, Light grey, and Dark grey
    Numbers /20 to /80 in the Trade Designation represent the shore hardness
[2] This product has also been evaluated for use in Mechanical Plumbing Device applications
    with a maximum surface area to volume ratio of 20 sq. in./L.
[3] This product has also been evaluated for use in Mechanical Plumbing Device applications
    with a maximum surface area to volume ratio of 2.0 sq. in./L.

O-Rings
ME0195/40[2] 20 sq. in./L C. HOT EPDM
ME0195/45[2] 20 sq. in./L C. HOT EPDM
ME0195/50[2] 20 sq. in./L C. HOT EPDM
ME0195/55[2] 20 sq. in./L C. HOT EPDM
ME0195/60[2] 20 sq. in./L C. HOT EPDM
ME0195/65[2] 20 sq. in./L C. HOT EPDM
ME0195/70[2] 20 sq. in./L C. HOT EPDM
ME0195/75[2] 20 sq. in./L C. HOT EPDM
ME0195/80[2] 20 sq. in./L C. HOT EPDM
ME0195/85[3] 20 sq. in./L C. HOT EPDM
ME0195/90[3] 20 sq. in./L C. HOT EPDM
ME0201/70V[3] 20 sq. in./L C. HOT FE
ME0940/40 20 sq. in./L C. HOT EPDM
ME0940/45 20 sq. in./L C. HOT EPDM
ME0940/50[2] 20 sq. in./L C. HOT EPDM
ME0940/55[2] 20 sq. in./L C. HOT EPDM
ME0940/60[2] 20 sq. in./L C. HOT EPDM
ME0940/65[2] 20 sq. in./L C. HOT EPDM
ME0940/70[2] 20 sq. in./L C. HOT EPDM
ME0940/75[2] 20 sq. in./L C. HOT EPDM
ME0940/80[2] 20 sq. in./L C. HOT EPDM
ME0940/85[3] 20 sq. in./L C. HOT EPDM
ME0940/90[3] 20 sq. in./L C. HOT EPDM
ME0996/40[2] 20 sq. in./L C. HOT NBR
ME0996/45[2] 20 sq. in./L C. HOT NBR
ME0996/50[2] 20 sq. in./L C. HOT NBR
ME0996/55[2] 20 sq. in./L C. HOT NBR
ME0996/60[2] 20 sq. in./L C. HOT NBR
ME0996/65[2] 20 sq. in./L C. HOT NBR
ME0996/70[2] 20 sq. in./L C. HOT NBR
ME0996/75[2] 20 sq. in./L C. HOT NBR
ME0996/80[2] 20 sq. in./L C. HOT NBR
ME0996/85[2] 20 sq. in./L C. HOT NBR
ME0996/90[2] 20 sq. in./L C. HOT NBR
ME2020/20[1] [2] 20 sq. in./L C. HOT SLC
ME2020/25[1] [2] 20 sq. in./L C. HOT SLC
ME2020/30[1] [2] 20 sq. in./L C. HOT SLC
ME2020/35[1] [2] 20 sq. in./L C. HOT SLC
ME2020/40[1] [2] 20 sq. in./L C. HOT SLC
ME2020/45[1] [2] 20 sq. in./L C. HOT SLC
ME2020/50[1] [2] 20 sq. in./L C. HOT SLC
ME2020/55[1] [2] 20 sq. in./L C. HOT SLC
ME2020/60[1] [2] 20 sq. in./L C. HOT SLC
ME2020/65[1] [2] 20 sq. in./L C. HOT SLC
ME2020/70[1] [2] 20 sq. in./L C. HOT SLC
ME2020/75[1] [2] 20 sq. in./L C. HOT SLC
ME2020/80[1] [2] 20 sq. in./L C. HOT SLC

[1] This product is Certified for the following colors:
    Transparent (no color), White, Black, Red, Red 3000, Blue, Yellow, Light green, Dark
    green, Light grey, and Dark grey
    Numbers /20 to /80 in the Trade Designation represent the shore hardness
[2] This product has also been evaluated for use in Mechanical Plumbing Device applications
    with a maximum surface area to volume ratio of 20 sq. in./L.
[3] This product has also been evaluated for use in Mechanical Plumbing Device applications
    with a maximum surface area to volume ratio of 2.0 sq. in./L.



 
Escort Seal (Shanghai) Co., Ltd. 
6F-10, No. 26, Taiyuan St
Jhubei City, Hsinchu County 302 
Taiwan 
886 3 552 6686
Visit this company's website

Facility : Shanghai, China

Joining and Sealing Materials

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Gasket/Sealing Materials
ME70-51B[2] [1] C. HOT EPDM
MN70-51B[3] [4] C. HOT NBR

[1] Certified for a maximum surface area to volume ratio of 2.0 sq. in./L.
[2] This product has also been evaluated for use in Mechanical Plumbing Device applications
    with a maximum surface area to volume ratio of 0.5 sq. in./L.
[3] This product has also been evaluated for use in Mechanical Plumbing Device applications
    with a maximum surface area to volume ratio of 0.1 sq. in./L.
[4] Certified for a maximum surface area to volume ratio of 1.0 sq. in./L.

O-Rings
ME70-51B[2] [1] C. HOT EPDM

[1] Certified for a maximum surface area to volume ratio of 2.0 sq. in./L.
[2] This product has also been evaluated for use in Mechanical Plumbing Device applications
    with a maximum surface area to volume ratio of 0.5 sq. in./L.



 
ESPLEX International, LLC 
P.O. Box 210817
Royal Palm Beach, FL 33421 
United States 
561-383-5654

Facility : # 1 USA

Joining and Sealing Materials

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Patching Materials
PLEX STICK [1] C. HOT EPOXY

[1] The exposed surface area of each sealant in a household distribution system shall not
    exceed 1.3 sq. cm/L or .2 sq. in./L



 
Fannteer Co., Ltd. 
3F, No. 392, Section 1, Neihu Road
Neihu District, Taipei City 11493 
Taiwan 
886 22 798 6583
Visit this company's website

Facility : Shanghai, China

Joining and Sealing Materials

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Gasket/Sealing Materials
E37049F [2] C. HOT EPDM
EP32670 [2] C. HOT EPDM
EP601158C [2] C. HOT EPDM
EP6101 [1] C. HOT EPDM
EP701168B[4] [2] C. HOT EPDM
EP701253C [2] C. HOT EPDM
EP7012OF[4] [2] C. HOT EPDM
EP7069OF[4] [2] C. HOT EPDM
EP70A9OF[4] [2] C. HOT EPDM
EP7101 [1] C. HOT EPDM
EP7103 [1] C. HOT EPDM
EP8079OF[4] [2] C. HOT EPDM
EP8101 [1] C. HOT EPDM
MQ3001[3] [2] C. HOT SLC
MQ7001[3] [2] C. HOT SLC
MQ7001[G] [2] C. HOT SLC
N67088F [2] C. HOT NBR
N67588F [2] C. HOT NBR
N7101 [2] C. HOT NBR
N7521 [2] C. HOT NBR
N8101 [2] C. HOT NBR
N9021F [2] C. HOT NBR
N9101 [2] C. HOT NBR
SI603073[3] [2] C. HOT SLC
SI603073[G] [2] C. HOT SLC
SI702002[G] [2] C. HOT SLC
VI759015A[5] [2] C. HOT FE

[1] Certified for a maximum surface area to volume ratio of 1 sq. in./L.
[2] Certified for a maximum surface area to volume ratio of 2.0 sq. in./L.
[3] This product has also been evaluated for use in Mechanical Plumbing Device applications
    with a maximum surface area to volume ratio of 2.0 sq. in./L.
[4] This product has also been evaluated for use in Mechanical Plumbing Device applications
    with a maximum use restriction of 0.9 sq. in./L.
[5] This product has also been evaluated for use in Mechanical Plumbing Device applications
    with a maximum use restriction of 0.2 sq. in./L.
[G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for
    “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state
    laws and the U.S. Safe Drinking Water Act.

    

O-Rings
E37049F [2] C. HOT EPDM
EP32670 [2] C. HOT EPDM
EP601158C [2] C. HOT EPDM
EP701168B[4] [2] C. HOT EPDM
EP701253C [2] C. HOT EPDM
EP7012OF[4] [2] C. HOT EPDM
EP7069OF[4] [2] C. HOT EPDM
EP70A9OF[4] [2] C. HOT EPDM
EP8079OF[4] [2] C. HOT EPDM
MQ7001[G] [2] C. HOT SLC
N67088F [2] C. HOT NBR
N67588F [2] C. HOT NBR
SI603073[G] [2] C. HOT SLC
SI702002[G] [2] C. HOT SLC
VI759015A[5] [2] C. HOT FE

[2] Certified for a maximum surface area to volume ratio of 2.0 sq. in./L.
[4] This product has also been evaluated for use in Mechanical Plumbing Device applications
    with a maximum use restriction of 0.9 sq. in./L.
[5] This product has also been evaluated for use in Mechanical Plumbing Device applications
    with a maximum use restriction of 0.2 sq. in./L.
[G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for
    “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state
    laws and the U.S. Safe Drinking Water Act.

    



 
Fannteer Co., Ltd. 
68 8F, Kuangfu North Road
Taipei 10560 
Taiwan 
886 22 577 4691

Facility : Changhua Hsien, Taiwan

Joining and Sealing Materials

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Gasket/Sealing Materials
EP701253C [1] C. HOT EPDM

[1] Certified for a maximum surface area to volume ratio of 2.0 sq. in./L.



 
Ferolite Jointings Ltd. 
C-178, Site No. 1
B.S. Road Industrial Area 
Ghaziabad, U.P 201001 
India 
91 120 4051500
Visit this company's website

Facility : Ghaziabad, India

Joining and Sealing Materials

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Gasket/Sealing Materials
Ferolite NAM 37C [1] C. HOT NBR

[1] Certified for a maximum surface area to volume ratio of 2.0 sq. in./L.



 
Fiske Brothers Refining Co. DBA Lubriplate Lubricants 
1500 Oakdale Avenue
Toledo, OH 43605 
United States 
800-347-5343 
419-691-2491

Facility : # 1 USA

Joining and Sealing Materials

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Lubricants
Lubriplate V-61 Silicone Faucet Valve Lubricant >= 1/2" C. HOT SLC



 
Flowserve Sulphur Springs Operation 
1511 Jefferson Street
Sulphur Springs, TX 75482 
United States 
903-439-3151

Facility : Sulphur Springs, TX

Joining and Sealing Materials

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Lubricants
BTR Valve Sealant #234 >= 1/2" CLD 23 SLC
Nordstrom Valve Sealant #234 >= 1/2" CLD 23 SLC
BTR Valve Sealant #421[1] >= 1/2" CLD 23 HC
Nordstrom Valve Sealant #421[1] >= 1/2" CLD 23 HC

[1] Suffix letters A, B, C, D, G, J, and K indicate stick size.



 
Freudenberg Sealing Technologies GmbH & Co. KG 
Oberwihl 4
79733 Goerwihl 
Italy 
49 7754 701320

Facility : Goerwihl, Germany

Joining and Sealing Materials

    Water Water
    Contact Contact
Trade Designation Size Temp Material

O-Rings
70 EPDM 281 [1] C. HOT EPDM
70 EPDM 291 [1] C. HOT EPDM
70 NBR 150 [2] C. HOT NBR
85 EPDM 292 [1] C. HOT EPDM

[1] Certified for a maximum surface area to volume ratio of 2.0 sq. in./L.
[2] Certified for a maximum surface area to volume ratio of 1.5 sq. in./L.


Facility : Castelli Calepio, Italy

Joining and Sealing Materials

    Water Water
    Contact Contact
Trade Designation Size Temp Material

O-Rings
70 EPDM 281 [1] C. HOT EPDM
70 NBR 150 [1] C. HOT NBR
85 EPDM 292 [1] C. HOT EPDM
70 EPDM 291 [1] C. HOT EPDM

[1] Certified for a maximum surface area to volume ratio of 2.0 sq. in./L.



 
Freudenberg Sealing Technologies GmbH & Co. KG 
Höhnerweg 2-4
69469 Weinheim/Bergstraße 
Germany 
49 407 5306 0
Visit this company's website

Facility : # 1 Germany

Joining and Sealing Materials

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Gasket/Sealing Materials
94 AU 21700[2] [1] D. HOT PUR
94 AU 21730[2] [1] D. HOT PUR

[1] Certified for a maximum surface area to volume ratio of 2.0 square inches/L.
[2] This product has also been evaluated for use in Mechanical Plumbing Device applications
    with a maximum use restriction of 2.0 square inches/L.

O-Rings
94 AU 21700[2] [1] D. HOT PUR
94 AU 21730[2] [1] D. HOT PUR

[1] Certified for a maximum surface area to volume ratio of 2.0 square inches/L.
[2] This product has also been evaluated for use in Mechanical Plumbing Device applications
    with a maximum use restriction of 2.0 square inches/L.

NOTE: Only products bearing the NSF Mark on the product, product packaging, and/or
      documentation shipped with the product are Certified.


 
Freudenberg-NOK General Partnership 
47690 East Anchor Court
Plymouth, MI 48170 
United States 
800-533-5656 
714-834-0602
Visit this company's website

Facility : Santa Ana, CA

Joining and Sealing Materials

    Water Water
    Contact Contact
Trade Designation Size Temp Material

O-Rings
E429 [1] C. HOT EPDM
N418 [2] C. HOT NBR

[1] Certified for a maximum surface area to volume ratio of 0.8 sq. in./L.
[2] Certified for a maximum surface area to volume ratio of 0.15 sq. in./L.



 
FS-Kunststofftechnologie GmbH & Co. KG 
Hahnenseifener Straße 15
51580 Reichshof-Hahn 
Germany 
49 229 791 030
Visit this company's website

Facility : # 1 Germany

Joining and Sealing Materials

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Sealants
Trinkwasser- und Lebensmittelsilikon A 4357 >= 1/2" CLD 23 SLT



 
Fuchs Lubricants Company - Kansas City Division 
2140 South 88th Street
Kansas City, KS 66111 
United States 
800-800-6457 
913-422-4022

Facility : Kansas City, KS

Joining and Sealing Materials

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Lubricants
Chemplex 862 >= 1/2" pipe C. HOT LUB
Chemplex 867 >= 1/2" pipe C. HOT LUB
Chemplex 868 >= 1/2" pipe C. HOT LUB



 
G.F. Thompson Co. Ltd. 
620 Steven Court
Newmarket, ON L3Y 6Z2 
Canada 
905-898-2557

Facility : Newmarket, Ontario, Canada

Joining and Sealing Materials

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Brazing/Solders/Fluxes[G]
Masters Soldering Paste >= 1/2" C. HOT SLDR
Masters Tinning Flux >= 1/2" C. HOT FLX

[G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for
    “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state
    laws and the U.S. Safe Drinking Water Act.

    

Thread Compounds[G]
BURNLEY PIPE THREAD SEALANT >= 1/2" C. HOT TC
Master's Pro-Blue >= 1/2" C. HOT TC
MASTERS PRO-DOPE >= 1/2" C. HOT TC

[G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for
    “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state
    laws and the U.S. Safe Drinking Water Act.

    



 
GAPI S.p.A 
Viale Europa 47
25036 Palazzolo 
Italy 
39 03 073 00221
Visit this company's website

Facility : Palazzolo, Italy

Joining and Sealing Materials

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Gasket/Sealing Materials
PTFE FE 1000[1] [2] [3] [4] C. HOT PTFE

[1] This product has also been evaluated for use in Mechanical Plumbing Device applications
    with a maximum use restriction of 4.0 sq. in./L.
[2] PTFE FE 1000 includes both finished parts machined by GAPI S.p.A and semi-finished PTFE
    shapes molded or extruded by GAPI S.p.A.  Parts machined from semi-finished PTFE shapes
    by entities other than GAPI S.p.A will not be NSF Certified and may not bear the NSF
    mark without prior authorization from NSF International.
[3] Only products bearing the NSF Mark on the product, product packaging, and/or
    documentation shipped with the product are Certified.
[4] Certified for a maximum surface area to volume ratio of 4.0 sq. in./L.



 
Garlock Sealing Technologies 
1666 Division Street
Palmyra, NY 14534 
United States 
800-448-6688 
315-597-3231
Visit this company's website

Facility : Palmyra, NY

Joining and Sealing Materials

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Gasket/Sealing Materials
Garlock Gylon Style 3522[G] [1] CLD 23 PTFE
Garlock Multi-Swell™ (Style 3760-U) - Palmyra[G] [2] CLD 23 OTHER
Stress Saver® XP[3] [G] 1" - 24" C. HOT FE
Style 3505 Blue Gylon®[3] [G] 1" - 144" CLD 23 PTFE
Style 3505 Blue Gylon® Stress Saver[3] [G] 1" - 144" CLD 23 PTFE

[1] Certified for a maximum surface area to volume ratio of 2.0 sq. in./L.
[2] Certified for a maximum width of 1/16" when used with 6" and greater diameter pipes (but
    less than 10") and a width of 1/8" when used with 10" and greater diameter pipes.
[3] Certified for distribution systems only, with width exposures of no more than 1/2" in
    pipes with diameters shown in 'Size'.
[G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for
    “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state
    laws and the U.S. Safe Drinking Water Act.

    



 
GE Mao Rubber Industrial Co., Ltd. 
No. 15, Kung-Yeh East 4th Road
Lu-Kang Chen, Changhua Hsien 
Taiwan 
886 4 7810288
Visit this company's website

Facility : Zhan-Shan City, China

Joining and Sealing Materials

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Gasket/Sealing Materials
E7042AA [1] C. HOT EPDM
E7051AA[4] [1] C. HOT EPDM
E7041 AA[2] [1] C. HOT EPDM
N7041 AA[3] [1] D. HOT NBR
S7031 AB [1] C. HOT SLC

[1] Certified for a maximum surface area to volume ratio of 2.0 sq. in./L.
[2] This product has also been evaluated for use in Mechanical Plumbing Device applications
    with a maximum surface area to volume ratio of 2.0 sq. in./L.
[3] This product has also been evaluated for use in Mechanical Plumbing Device applications
    with a maximum surface area to volume ratio of 0.2 sq. in./L.
[4] This product has also been evaluated for use in Mechanical Plumbing Device applications
    with a maximum surface area to volume ratio of 0.4 sq. in./L.

O-Rings
E7042AA [1] C. HOT EPDM
E7051AA[4] [1] C. HOT EPDM
E7041 AA[2] [1] C. HOT EPDM
N7041 AA[3] [1] D. HOT NBR
S7031 AB [1] C. HOT SLC

[1] Certified for a maximum surface area to volume ratio of 2.0 sq. in./L.
[2] This product has also been evaluated for use in Mechanical Plumbing Device applications
    with a maximum surface area to volume ratio of 2.0 sq. in./L.
[3] This product has also been evaluated for use in Mechanical Plumbing Device applications
    with a maximum surface area to volume ratio of 0.2 sq. in./L.
[4] This product has also been evaluated for use in Mechanical Plumbing Device applications
    with a maximum surface area to volume ratio of 0.4 sq. in./L.



 
GE Mao Rubber Industrial Co., Ltd. 
No. 15, Kung-Yeh East 4th Road
Lu-Kang Chen, Changhua Hsien 
Taiwan 
886 47810288

Facility : Changhua Hsien, Taiwan

Joining and Sealing Materials

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Gasket/Sealing Materials
E7083AA [1] C. HOT EPDM

[1] Certified for a maximum surface area to volume ratio of 2.0 sq. in./L.



 
General Sealants, Inc. 
300 South Turnbull Canyon Road
City of Industry, CA 91745-1009 
United States 
800-762-1144 
626-961-0211

Facility : City of Industry, CA

Joining and Sealing Materials

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Sealants
GS #79 Sealant >= 1/2" Pipe CLD 23 PB



 
GPT 
4990 Iris Street
Wheat Ridge, CO 80033 
United States 
800-423-2410 
303-988-1242
Visit this company's website

Facility : Houston, TX

Joining and Sealing Materials

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Gasket/Sealing Materials
PSI Link Seal Modular Seal (LS-XXX-S61™-Y)[1] [2] CLD 23 MLTPL

[1] XXX - Thickness of the gasket and may be 200, 275, 300, 315, 325, 340, 360, 400, 410, 
          425, 475, 500, 525, 575, 600, or 650.
    Y   - Number of links and may be any number from 4-43.
[2] Certified for sealing the annular space between the outside of the pipe and the tank
    wall at a maximum use of 1 link per 5.8 gallons of water.



 
Green Mountain International, LLC 
235 Pigeon Street
Waynesville, NC 28786 
United States 
800-942-5151 
828-456-9970
Visit this company's website

Facility : Canton, GA

Joining and Sealing Materials

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Grouts
Flex Classic[1] [2] CLD 23 PUR

[1] Product is Certified when mixed with up to 2.5% Mountain Grout Accelerator.
[2] Certified for the following applications:
    Tank interior surfaces not to exceed 1.5% of tanks 100 - 500 gallons.
    Tank interior surfaces not to exceed 2.5% of tanks 500 - 1000 gallons.
    Tank interior surfaces not to exceed 3.5% of tanks 1000 gallons and greater.



 
Gripper Gasket LLC 
P.O. Box 1475
Corona, CA 92878 
United States 
951-479-4999
Visit this company's website

Facility : Memphis, TN

Joining and Sealing Materials

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Gasket/Sealing Materials
Gripper Gasket® >= 3" pipe CLD 23 SBR
Restrained Joint Gasket >= 3" pipe CLD 23 SBR



 
Gulf Rubber Australia Pty Ltd. 
12-13 Green Street
Revesby 
Sydney, NSW 2212 
Australia 
61 2 9772 4877
Visit this company's website

Facility : Guang Dong, China

Joining and Sealing Materials

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Gasket/Sealing Materials
Gulf Rubber Compound 9711 [1] [2] D. HOT EPDM
Gulf Rubber Compound 9711\2 [1] [2] D. HOT EPDM

[1] Certified for a maximum surface area to volume ratio of 2.0 sq. in./L.
[2] This product has also been evaluated for use in Mechanical Plumbing Device applications
    with a maximum surface area to volume ratio of 1.0 sq. in./L.

O-Rings
Gulf Rubber Compound 9711 [1] [2] D. HOT EPDM
Gulf rubber Compound 9711\2 [1] [2] D. HOT EPDM

[1] Certified for a maximum surface area to volume ratio of 2.0 sq. in./L.
[2] This product has also been evaluated for use in Mechanical Plumbing Device applications
    with a maximum surface area to volume ratio of 1.0 sq. in./L.


Facility : Shanghai, China

Joining and Sealing Materials

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Gasket/Sealing Materials
Gulf Rubber Compound N27102 [1] CLD 23 SBR

[1] Certified for a maximum surface area to volume ratio of 0.4 sq. in./L.

O-Rings
Gulf Rubber Compound N27102 [1] CLD 23 SBR

[1] Certified for a maximum surface area to volume ratio of 0.4 sq. in./L.


Facility : Changhua Hsien, Taiwan

Joining and Sealing Materials

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Gasket/Sealing Materials
Gulf Rubber Formulation 7400 Silicone [2] CLD 23 SLC
Gulf Rubber Formulation 7400-7800 Silicone [2] CLD 23 SLC
Gulf Rubber Formulation 7500 Silicone [2] CLD 23 SLC
Gulf Rubber Formulation 7600 Silicone [2] CLD 23 SLC
Gulf Rubber Formulation 7700 Silicone [2] CLD 23 SLC
Gulf Rubber Formulation 7800 Silicone [2] CLD 23 SLC
Rubber Compound E16 60-80[1] [2] CLD 23 EPDM
Rubber Compound E51 60-80[3] [2] CLD 23 EPDM

[1] This product has also been evaluated for use in Mechanical Plumbing Device applications
    with a maximum use restriction of 2.0 sq. in./L.
[2] Certified for a maximum surface area to volume ratio of 2.0 sq. in./L.
[3] This product has also been evaluated for use in Mechanical Plumbing Device applications
    with a maximum use restriction of 1.5 sq. in./L.

O-Rings
Gulf Rubber Formulation 7400 Silicone [2] CLD 23 SLC
Gulf Rubber Formulation 7400-7800 Silicone [2] CLD 23 SLC
Gulf Rubber Formulation 7500 Silicone [2] CLD 23 SLC
Gulf Rubber Formulation 7600 Silicone [2] CLD 23 SLC
Gulf Rubber Formulation 7700 Silicone [2] CLD 23 SLC
Gulf Rubber Formulation 7800 Silicone [2] CLD 23 SLC
Rubber Compound E16 60-80[1] [2] CLD 23 EPDM
Rubber Compound E51 60-80[3] [2] CLD 23 EPDM

[1] This product has also been evaluated for use in Mechanical Plumbing Device applications
    with a maximum use restriction of 2.0 sq. in./L.
[2] Certified for a maximum surface area to volume ratio of 2.0 sq. in./L.
[3] This product has also been evaluated for use in Mechanical Plumbing Device applications
    with a maximum use restriction of 1.5 sq. in./L.


Facility : Ho Chi Minh City, Vietnam

Joining and Sealing Materials

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Gasket/Sealing Materials
Gulf Rubber Compound E16 60-80[1] [2] CLD 23 EPDM
Gulf Rubber Compound N25102 [3] CLD 23 SBR
Gulf Rubber E51 60-80[4] [2] CLD 23 EPDM
Gulf Rubber Formulation 5619, 55 Duro EPDM[5] [6] CLD 23 EPDM
Gulf Rubber Formulation 5619, 60 Duro EPDM[5] [6] CLD 23 EPDM
Gulf Rubber Formulation 5619, 65 Duro EPDM[5] [6] CLD 23 EPDM
Gulf Rubber Formulation 7400 [2] CLD 23 SLC
Gulf Rubber Formulation 7400-7800 Silicone [2] CLD 23 SLC
Gulf Rubber Formulation 7500 [2] CLD 23 SLC
Gulf Rubber Formulation 7600 [2] CLD 23 SLC
Gulf Rubber Formulation 7700 [2] CLD 23 SLC
Gulf Rubber Formulation 7800 [2] CLD 23 SLC
Gulf Rubber Formulation EPDM 5517 [2] CLD 23 EPDM
Gulf Rubber Formulation NBR 4516 [2] CLD 23 NBR

[1] This product has been evaluated for use in Mechanical Plumbing Device applications with
    a maximum use restriction of 2.0 sq. in./L.
[2] Certified for a maximum surface area to volume ratio of 2.0 sq. in./L.
[3] Certified for a maximum surface area to volume ratio of 0.8 sq. in./L.
[4] This product has been evaluated for use in Mechanical Plumbing Device applications with
    a maximum use restriction of 0.6 sq. in/L.
[5] This product has also been evaluated for use in Mechanical Plumbing Device applications
    with a maximum use restriction of 0.15 sq. in./L.
[6] Certified for a maximum surface area to volume ratio of 1.5 sq. in./L.

O-Rings
Gulf Rubber Compound E16 60-80[1] [2] CLD 23 EPDM
Gulf Rubber Compound N25102 [3] CLD 23 SBR
Gulf Rubber E51 60-80[4] [2] CLD 23 EPDM
Gulf Rubber Formulation 7400 [2] CLD 23 SLC
Gulf Rubber Formulation 7400-7800 Silicone [2] CLD 23 SLC
Gulf Rubber Formulation 7500 [2] CLD 23 SLC
Gulf Rubber Formulation 7600 [2] CLD 23 SLC
Gulf Rubber Formulation 7700 [2] CLD 23 SLC
Gulf Rubber Formulation 7800 [2] CLD 23 SLC

[1] This product has been evaluated for use in Mechanical Plumbing Device applications with
    a maximum use restriction of 2.0 sq. in./L.
[2] Certified for a maximum surface area to volume ratio of 2.0 sq. in./L.
[3] Certified for a maximum surface area to volume ratio of 0.8 sq. in./L.
[4] This product has been evaluated for use in Mechanical Plumbing Device applications with
    a maximum use restriction of 0.6 sq. in/L.



 
Guy Chemical Company, Inc. 
150 Dominion Drive
Somerset, PA 15501 
United States 
814-443-9455
Visit this company's website

Facility : Somerset, PA

Joining and Sealing Materials

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Lubricants
GCC-1000 >= 1/2" C. HOT LUB

Thread Compounds
GCC-1000 >= 1/2" C. HOT LUB



 
H.B. Fuller Company 
1200 Willow Lake Boulevard
St. Paul, MN 55110-5101 
United States 
651-236-5900
Visit this company's website

Facility : Grand Rapids, MI

Joining and Sealing Materials

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Adhesives
UR3501A and UR3501B [1] D. HOT ADH
UR3577[G] [2] D. HOT ADH
UR3577LV[G] [2] D. HOT ADH
UR3579[G] [2] D. HOT ADH

[1] Mix ratio is 100:50 (A:B) by volume or 100:62.5 (A:B) by weight.  Minimum cure time is 7
    days at 77°F then 3 hours at 158°F.
[2] Mix ratio is 100:100 (A:B) by volume or 100:110 (A:B) by weight with a maximum dry film
    thickness of 50 mils.  Minimum cure time is 7 days at 77°F then 3 hours at 158°F
[G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for
    “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state
    laws and the U.S. Safe Drinking Water Act.

    



 
Hamilton Kent Inc. 
77 Carlingview Drive
Toronto, ON M9W 5E6 
Canada 
416-675-9873
Visit this company's website

Facility : Toronto, Ontario, Canada

Joining and Sealing Materials

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Gasket/Sealing Materials
Centurion[1] [4] 4" - 48" CLD 23 NBR
Centurion[1] [5] 4" - 48" CLD 23 IR
Centurion[3] [G] 4" - 48" CLD 23 EPDM
Centurion[1] [2] [G] 4" - 48" CLD 23 IR
SHURE-LOK[1] [2] [G] 4" - 48 CLD 23 IR
SHURE-LOK[1] [4] 4" - 48" CLD 23 NBR
SHURE-LOK[3] [G] 4" - 24" CLD 23 EPDM

[1] Certified for a maximum surface area to volume ratio not to exceed 0.048 sq. in./L.
[2] Includes Compound 800366.
[3] Includes Compound 800566.
[4] Includes Compound 800664.
[5] Includes Compound 800369.
[G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for
    “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state
    laws and the U.S. Safe Drinking Water Act.

    



 
Hangzhou PASS Fluid Equipment Co., Ltd. 
No. 317 Huafeng Road
Hangzhou 310022 
China 
86 1330 652 7565

Facility : Qingdao, China

Joining and Sealing Materials

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Gasket/Sealing Materials
108 Gasket [1] C. HOT EPDM
114.3 Gasket [1] C. HOT EPDM
133 Gasket [1] C. HOT EPDM
139.7/141.3 Gasket [1] C. HOT EPDM
159 Gasket [1] C. HOT EPDM
168.3 Gasket [1] C. HOT EPDM
219.1 Gasket [1] C. HOT EPDM
26.9 Gasket [1] C. HOT EPDM
273 Gasket [1] C. HOT EPDM
32 Gasket [1] C. HOT EPDM
323.9 Gasket [1] C. HOT EPDM
33.7 Gasket [1] C. HOT EPDM
38 Gasket [1] C. HOT EPDM
42.4 Gasket [1] C. HOT EPDM
48.3 Gasket [1] C. HOT EPDM
57 Gasket [1] C. HOT EPDM
60.3 Gasket [1] C. HOT EPDM
73 Gasket [1] C. HOT EPDM
76.1 Gasket [1] C. HOT EPDM
88.9 Gasket [1] C. HOT EPDM

[1] Certified for a maximum surface area to volume ratio of 2 sq. in./L.



 
Hansecom Italia SRL Unipersonale 
Via del Risorgimento 36
24060 Villongo (BG) 
Italy 
39 035 92 79 44

Facility : Chiuduno (BG), Italy

Joining and Sealing Materials

    Water Water
    Contact Contact
Trade Designation Size Temp Material

O-Rings
EPDMPX70/A4 [1] C. HOT EPDM

[1] Certified for a maximum surface area to volume ratio of 2.0 sq. in./L.



 
HCC Holdings Inc. 
4700 West 160th Street
Cleveland, OH 44135 
United States 
216-267-7100

Facility : Cleveland, OH

Joining and Sealing Materials

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Thread Compounds
Grrip Thread Sealant >= 1/2" C. HOT SLT
Megaloc >= 1/2" C. HOT TC
Pro-Dope >= 1/2" C. HOT TC
Real Tuff Thread Sealant >= 1/2" C. HOT TC



 
HCC Holdings, Inc. An Oatey Affiliate 
4700 West 160th Street
Cleveland, OH 44135 
United States 
973-778-5000

Facility : # 1 USA

Joining and Sealing Materials

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Patching Materials
Pro Poxy-20 [1] C. HOT EPOXY
Plastic Poxy [1] C. HOT EPOXY

[1] The exposed surface area of each sealant in a household distribution system
    should not exceed 1.3 sq. cm/L or 0.2 sq. in./L.



 
Henkel Corporation 
One Henkel Way
Rocky Hill, CT 06067 
United States 
860-571-5100
Visit this company's website

Facility : Clearwater, FL

Joining and Sealing Materials

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Adhesives
Macroplast UK 178A and 178B[2] [1] D. HOT ADH

[1] Mix ratio is 1:1 (A:B) by volume.
[2] Minimum cure time is 7 days.


Facility : Seabrook, NH

Joining and Sealing Materials

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Adhesives
Loctite® 7649 Primer N[1] [2] 4.5 joints/L C. HOT JNG
Loctite® Speedbonder® H3101[3] [4] [5] CLD 23 ADH

[1] Evaluated for use with Henkel Loctite's anaerobic adhesives and sealants.
[2] Only products bearing the NSF Mark on the product, product packaging, and/or
    documentation shipped with the product are Certified.
[3] Mix ratio is 1:1 (A:B) by weight or volume.
[4] Certification does not include use with Primer 2000.
[5] Certified for joining pipes and fittings 4 inches and greater.


Facility : Cleveland, OH

Joining and Sealing Materials

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Sealants
Loctite® Resinol® 90C[1] [2] C. HOT SLT
Loctite® Resinol® RTC [3] C. HOT SLT

[1] Certified for use with brass materials having no greater than 20% porosity.
[2] Maximum use level for residential applications is 31 sq.in./L.
[3] Maximum use level for residential applications is 31 sq. in./L (335 sq. in. per
    residence).


Facility : Glenwillow, OH

Joining and Sealing Materials

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Sealants [G]
Loctite Epoxy Putty All-Purpose [1] C. HOT EPOXY

[1] The exposed surface area of each sealant in a household distribution system shall not
    exceed 1.3 sq. cm/L or 0.2 sq. in./L
[G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for
    “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state
    laws and the U.S. Safe Drinking Water Act.

    


Facility : Jilemnice, Czech Republic

Joining and Sealing Materials

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Sealants
Loctite 55 Pipe Sealing CordNOTE: >= 1/4" C. HOT SLT
Loctite 55XL >= 1/4" C. HOT SLT
Tangit UNI-LOCK >= 1/4" C. HOT SLT
UNI-LOCK >= 1/4" C. HOT SLT

NOTE: Only products bearing the NSF Mark on the product, product packaging, and/or
      documentation shipped with the product are Certified.

Thread Compounds
Loctite 55 Pipe Sealing CordNOTE: >= 1/4" C. HOT TC
Loctite 55XL >= 1/4" C. HOT SLT
Tangit UNI-LOCK >= 1/4" C. HOT TC

NOTE: Only products bearing the NSF Mark on the product, product packaging, and/or
      documentation shipped with the product are Certified.


Facility : Düsseldorf, Germany

Joining and Sealing Materials

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Adhesives
Loctite UK 178-1 A and 178B[2] [1] D. HOT ADH
Loctite UK 178A and 178B[2] [1] D. HOT ADH

[1] Mix ratio is 1:1 (A:B) by volume.
[2] Minimum cure time is 7 days.


Facility : Dublin, Ireland

Joining and Sealing Materials

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Adhesives
LOCTITE® 5776™[1] [2] >= 1/2" C. HOT ADH

[1] Certified for use without activators.
[2] Certified for a maximum of 10 joints per liter.


Facility : Sabana Grande, Puerto Rico

Joining and Sealing Materials

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Adhesives
LOCTITE® 263[1] [2] [3] >= 1/2" C. HOT ADH
Loctite 648[1] [10] >= 1/2" C. HOT ADH
Loctite® 242 Threadlocker Adhesive[1] [2] >= 1/2" D. HOT SLT
Loctite® 680 Retaining Compound[1] [4] >= 1/2" C. HOT ADH

[1] Only products bearing the NSF Mark on the product, product packaging, and/or
    documentation shipped with the product are Certified.
[2] Certified for a maximum use of 2 joints/liter.
[3] Certified for use without activators.
[4] Maximum use: 10 (1/2") joints per liter.
[10] Certification does not include activators.

Sealants
Loctite® 290 Threadlocker Adhesive[1] [2] >= 1/2" D. HOT SLT
Loctite® 565 PST® Pipe Sealant[1] [5] [6] C. HOT TS
Loctite® PST® 561 Pipe Sealant Stick[1] [7] D. HOT SLT
Sprinkler System Thread Sealant[1] [5] [6] C. HOT TS
Sprinkler System Weld Sealant[1] [2] >= 1/2" D. HOT TS

[1] Only products bearing the NSF Mark on the product, product packaging, and/or
    documentation shipped with the product are Certified.
[2] Certified for a maximum use of 2 joints/liter.
[5] This product is Certified for use as a fitting and pipe sealant.
[6] Maximum use: 50 (1/2") joints per residence (4.5 joints per liter).
[7] Maximum of 5 joints per liter.

Thread Compounds
Hunting Interlock Seallube™ Tubular Thread Sealant - Field End >= 1/2" C. HOT TC
Hunting Interlock Seallube™ Tubular Thread Sealant - Mill End >= 1/2" C. HOT TC
Loctite® 480 Instant Adhesive[1] >= 1/2" C. HOT SLT
Loctite® 518 Flange Sealant[1] [8] >= 1/2" C. HOT SLT
Loctite® Threadlocker Adhesive 243[1] [8] >= 1/2" C. HOT TS
Seallube HTM-1001 >= 1/2" C. HOT TC
Seallube LTF - 4444 >= 1/2" C. HOT TC
Stainless Steel PST® 567[1] [9] C. HOT TC

[1] Only products bearing the NSF Mark on the product, product packaging, and/or
    documentation shipped with the product are Certified.
[8] Maximum of 21 joints per residence (2 joints per liter).
[9] Certified for use as an anode thread sealant in water heater tanks with a maximum
    surface area to volume ratio of 0.08 sq. in./L.



 
Henkel KGaA 
Henkelstrasse 67
D-40589 Düsseldorf 
Germany 
49 211 797 0

Facility : # 2 Germany

Joining and Sealing Materials

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Adhesives
CF 1000 [1] D. HOT EPOXY
CF 920 [1] D. HOT VE

[1] Certified for use as an anchoring adhesive for installing thread rods (less than or
    equal to 1.3 inches in diameter) in concrete or masonry for water treatment applications.



 
Henkel Loctite (China) Co., Ltd. 
No. 90, Zhujiang Road
Yantai, Shandong 
China 
86 21 28918768
Visit this company's website

Facility : Shandong, China

Joining and Sealing Materials

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Adhesives
Loctite UK 178A/Loctite UK 178B[1] [2] >= 1/2" D. HOT ADH

[1] Mix Ratio is 1:1 (A:B) by volume or 0.9:1 (A:B) by weight.
[2] Minimum cure time is 7 days.



 
Henkel Loctite Deutschland GmbH 
Arabellastrasse 17
81925 Muenchen 
Germany 
49 899 2680

Facility : # 1 USA

Joining and Sealing Materials

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Patching Materials
Loctite® 3463 Metal Magic Steel [1] C. HOT EPOXY
Metal Magic Steel [1] C. HOT EPOXY

[1] The exposed surface area of each sealant in a household distribution system shall not
    exceed 1.3 sq. cm/L or .2 sq. in./L



 
Henry Company - Sealants Division 
336 Cold Stream Road
Kimberton, PA 19442 
United States 
800-671-3002 
713-671-9280

Facility : Houston, TX

Joining and Sealing Materials

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Sealants
Synko-Flex®[2] [1] CLD 23 ASPH
Synko-Flex® PRIMER[3] [1] CLD 23 ASPH

[1] This product is Certified for a 100,000-gallon tank and greater.  As a water
    stop, it is restricted to use at a surface area to volume ratio of 0.003 square
    inches per liter.
[2] Certified for use only in conjunction with Synko-Flex® EMULSION PRIMER or PRIMER.
[3] Certified for use only in conjunction with Synko-Flex®.



 
Hercules Chemical Company, Inc. 
29 West 38th Street
New York, NY 10018 
United States 
973-778-5000

Facility : # 2 USA

Joining and Sealing Materials

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Lubricants[G]
Duck Butter Pipe Joint Lubricant >= 1/2" CLD 23 LUB

[G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for
    “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state
    laws and the U.S. Safe Drinking Water Act.

    



 
Hermann Otto GmbH 
Krankenhausstrasse 14
83413 Fridolfing 
Germany 
49 8684 908 452
Visit this company's website

Facility : Fridolfing, Germany

Joining and Sealing Materials

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Sealants
Ottoseal S 27 [1] CLD 23 SLT

[1] Certified for a maximum surface area to volume ratio of 7.3 sq. in./L.



 
Hernon Manufacturing, Inc. 
121 Tech Drive
Sanford, FL 32771 
United States 
407-322-4000
Visit this company's website

Facility : Sanford, FL

Joining and Sealing Materials

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Adhesives[1] [2]
Cylinlock 34323 N/A D. HOT ADH
Cylinlock 824 N/A D. HOT ADH
Cylinlock 843 N/A D. HOT ADH
Cylinlock 845 N/A D. HOT ADH
Cylinlock 846 N/A D. HOT ADH

[1] The product has also been evaluated for use in Mechanical Plumbing Device applications.
    Certification does not include a primer.
[2] Only products bearing the NSF Mark are Certified.

Sealants[2]
HPS 990 [3] C. HOT SLT

[2] Only products bearing the NSF Mark are Certified.
[3] Certified for a maximum surface area to volume ratio of 40 sq. in./L. Certified for
    brass materials having no greater than 28% porosity.

Thread Compounds[2]
Dripstop 923 >= 1/2" C. HOT TC
Self Seeler 604 >= 1/2" C. HOT ACR
Self Seeler 615 >= 1/2" C. HOT ACR
Self Seeler 616 >= 1/2" C. HOT ACR
Self Seeler 618 >= 1/2" C. HOT ACR

[2] Only products bearing the NSF Mark are Certified.



 
Hilti AG 
Feldkircherstrasse 100
FL-9494 
Liechtenstein 
423 234 2111
Visit this company's website

Facility : Kaufering, Germany

Joining and Sealing Materials

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Adhesives
HIT-HY200[1] NA D. HOT ADH
HIT-HY200-A[1] NA D. HOT ADH
HIT-HY200-R[1] NA D. HOT ADH
Hilti HIT-CT 1[2] NA CLD 23 ADH
Hilti HIT-HY 100[2] NA D. HOT ADH
Hilti HIT-HY 110[2] NA CLD 23 ADH
Hilti HIT-HY 150[2] NA CLD 23 ADH
Hilti HIT-HY 150 Adhesive Anchoring System[2] NA CLD 23 ADH
Hilti HIT-HY 150 Max[2] NA D. HOT ADH
Hilti HIT-HY 150 Max Adhesive Anchoring System[2] NA D. HOT ADH
Hilti HIT-HY 150 Max-SD[2] NA D. HOT ADH
Hilti HIT-RE 500[2] NA D. HOT EPOXY
Hilti HIT-RE 500 Adhesive Anchoring System[2] NA D. HOT EPOXY
Hilti HIT-RE 500 SD[2] NA D. HOT EPOXY
Hilti HIT-RE 500 SD Adhesive Anchoring System[2] NA D. HOT EPOXY
Hilti HIT–HY 150-FR[2] NA CLD 23 ADH
Hilti HIT–HY 150-FR Adhesive Anchoring System[2] NA CLD 23 ADH

[1] Certified for use as an anchoring adhesive for installing threaded rods (less than or
    equal to 32 mm in diameter) in concrete for water treatment applications.
[2] Product is Certified for use as an anchoring adhesive for installing threaded rods (less
    than or equal to 1.3 inches in diameter) in concrete for water treatment applications.



 
Hun-Yi Rubber Industrial Co. 
No. 323, Ren-Ay Road, Ho Mei Chen
Changhua Hsien 
Taiwan 
886 4 755 1315

Facility : Changhua Hsien, Taiwan

Joining and Sealing Materials

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Gasket/Sealing Materials
SE-419F[1] [2] C. HOT EPDM
SE-519F[3] [2] C. HOT EPDM
SE-619F [2] C. HOT EPDM
SE-629PF [2] C. HOT EPDM
SE-719F [2] C. HOT EPDM
SE-729PF [2] C. HOT EPDM
SE-819F [2] C. HOT EPDM
SE-829PF [2] C. HOT EPDM
SE-919F [2] C. HOT EPDM
SN-419F[3] [2] C. HOT NBR
SN-519F[3] [2] C. HOT NBR
SN-619F[3] [2] C. HOT NBR
SN-719F[3] [2] C. HOT NBR
SN-819F[3] [2] C. HOT NBR
SN-919F[4] [2] C. HOT NBR

[1] This product has also been evaluated for use in Mechanical Plumbing Device applications
    with a maximum use restriction of 0.4 sq. in/L.
[2] Certified for a maximum surface area to volume ratio of 2.0 sq. in./L.
[3] This product has also been evaluated for use in Mechanical Plumbing Device applications
    with a maximum use restriction of 0.2 sq. in/L.
[4] This product has also been evaluated for use in Mechanical Plumbing Device applications
    with a maximum use restriction of 0.3 sq. in./L.

O-Rings
SE-419F[1] [2] C. HOT EPDM
SE-519F[3] [2] C. HOT EPDM
SE-629PF [2] C. HOT EPDM
SE-729PF [2] C. HOT EPDM
SE-829PF [2] C. HOT EPDM

[1] This product has also been evaluated for use in Mechanical Plumbing Device applications
    with a maximum use restriction of 0.4 sq. in/L.
[2] Certified for a maximum surface area to volume ratio of 2.0 sq. in./L.
[3] This product has also been evaluated for use in Mechanical Plumbing Device applications
    with a maximum use restriction of 0.2 sq. in/L.



 
Hun-Yi Rubber Industrial Co., Ltd. 
No. 38, Lane 193, Hochen Road
Homei Town, Changhua County 
Taiwan 
886 47551315

Facility : Changhua Hsien, Taiwan

Joining and Sealing Materials

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Gasket/Sealing Materials
SE-718PF [1] C. HOT EPDM
SN-738PF [1] C. HOT NBR

[1] Certified for a maximum surface area to volume ratio of 2.0 sq. in./L.



 
Hutchinson - Le Joint Francais 
Zi de Bazouges
53200 Château-Gontier 
France 
33 2 4309 2320

Facility : Chateau-Gontier, France

Joining and Sealing Materials

    Water Water
    Contact Contact
Trade Designation Size Temp Material

O-Rings
7EP1197F (EPDM) [1] C. HOT EPDM
7PD1612F (NBR) [1] C. HOT NBR

[1] Certified for a maximum surface area to volume ratio of 2.0 sq. in./L.



 
Hutchinson Seal de Mexico S.A. de C.V. 
National O-Ring Division
Calle Pelicanos 313 
Col. Lomas de San Fernando, Ensenada 
Baja California C.P. 22785,  
Mexico 
52 646 152 2900

Facility : Ensenada Baja California, Mexico

Joining and Sealing Materials

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Gasket/Sealing Materials
D31 NBR [1] CLD 23 NBR
E08 EPDM [1] C. HOT EPDM
E09 EPDM [1] C. HOT EPDM
E14 EPDM [1] C. HOT EPDM
E16 EPDM [1] C. HOT EPDM
E20 EPDM [1] C. HOT EPDM
E37 EPDM [1] C. HOT EPDM
O-Rings and Molded Shapes [1] CLD 23 NBR

[1] Certified for a maximum surface area to volume ratio of 2.0 sq. in./L.

O-Rings
D31 NBR [1] CLD 23 NBR
O-Rings and Molded Shapes [1] CLD 23 NBR

[1] Certified for a maximum surface area to volume ratio of 2.0 sq. in./L.



 
Hydratech Engineered Products 
10448 Chester Road
Cincinnati, OH 45215 
United States 
513-827-9169
Visit this company's website

Facility : Cincinnati, OH

Joining and Sealing Materials

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Gasket/Sealing Materials
HydraTite Internal Sealing System[1] >= 18" CLD 23 MLTPL

[1] Certified for use in 18" and larger diameter pipe joints with a maximum exposed seal
    width of 15.5".



 
Hydroseal Canada 
20th Bay Street
12th Floor Water Park Place 
Toronto, ON M5J 2N8 
Canada 
416-848-0899
Visit this company's website

Facility : #100

Joining and Sealing Materials

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Solvent Cements
40 Callibre PVC Cement Clear[1] >= 1/2" CLD 23 NA

[1] The compliance of this product with the health effect requirements of NSF/ANSI Standard
    61 was determined based on the testing of pipe and fittings assembled using the cement
    and either 90 Callibre Primer Clear or 90 Callibre Primer Purple.



 
Højstrup Industrilim - C. Højstrup Aps 
Emil Neckelmanns Vej 11
DK-5220 Odense Sø 
Denmark 
45 66 17 18 02

Facility : # 1 Switzerland

Joining and Sealing Materials

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Adhesives
AN 150 >= 1/2" C. HOT ADH
AN 2510 >= 1/2" C. HOT ADH
AN 4000 >= 1/2" C. HOT ADH
AN 4001 >= 1/2" C. HOT ADH
AN 500 >= 1/2" C. HOT ADH
AN 550 >= 1/2" C. HOT ADH
AN 6500 >= 1/2" C. HOT ADH
AN 700 >= 1/2" C. HOT ADH
AN 7500 >= 1/2" C. HOT ADH
AN CA 20 >= 1/2" C. HOT ADH
AN CA 36 >= 1/2" C. HOT ADH
AN CA 37 >= 1/2" C. HOT ADH
AN CA 84 >= 1/2" C. HOT ADH
AN K024 >= 1/2" C. HOT ADH
AN K140[1] >= 1/2" C. HOT ADH
AN K400 >= 1/2" C. HOT ADH
AN K650[1] >= 1/2" C. HOT ADH

[1] Certification is based on a minimum cure of 72 hours at 75°F

Sealants
AN K050 >= 1/2" C. HOT SLT

Thread Compounds
AN 4001 >= 1/2" C. HOT TC
AN 500 >= 1/2" C. HOT TC
AN 6500 >= 1/2" C. HOT TC
AN 700 >= 1/2" C. HOT TC
AN K060 >= 1/2" C. HOT TC



 
IFS Industries, Inc. 
400 Orrton Avenue
Reading, PA 19611 
United States 
800-537-4502 
610-378-1381
Visit this company's website

Facility : Reading, PA

Joining and Sealing Materials

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Adhesives
Dura-Pro UL-4000A/UL-4000B[2] [1] C. HOT ADH
Dura-Pro UL-4001A/UL-4001B[2] [1] C. HOT ADH
Dura-Pro UL-4002A/UL-4002B[2] [1] C. HOT ADH
Dura-Pro UL-4003A/UL-4003B[2] [1] C. HOT ADH
Dura-Pro UL-4004A/UL-4004B[2] [1] C. HOT ADH
Dura-Pro UL-4005A/UL-4005B[2] [1] C. HOT ADH

[1] Mix ratio is 1:1 (A:B) by volume and 0.89:1 (A:B) by weight.
[2] Minimum cure time and temperature is 7 days at 75°F.



 
Illinois Tool Works Inc. DBA Permatex® and Devcon® Home 
Hartford Square North
10 Columbus Boulevard 
Hartford, CT 06106 
United States 
877-376-2839 
860-543-6981
Visit this company's website

Facility : # 1 USA

Joining and Sealing Materials

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Patching Materials
Devcon® home Steel Weld™ [1] C. HOT EPOXY
Devcon® home Water Bond™ [G] [1] C. HOT EPOXY
Plastic Bond [1] C. HOT EPOXY
Steel Weld™ [1] C. HOT EPOXY
Water Bond™[G] [1] C. HOT EPOXY

[1] The exposed surface area of each sealant in a household distribution system shall not
    exceed 1.3 sq. cm/L or .2 sq. in./L.
[G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for
    “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state
    laws and the U.S. Safe Drinking Water Act.

    



 
Imperial Western Products Co, Inc. 
86-600 Avenue 54
Coachella, CA 92236 
United States 
760-398-0815

Facility : Coachella, CA

Joining and Sealing Materials

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Lubricants
Enforce VSL-35 >= 1/2" CLD 23 LUB
Enforce VSL-35-2 >= 1/2" CLD 23 LUB
Enforce VSL-35-5 >= 1/2" CLD 23 LUB
Enforce VSL-35-6 >= 1/2" CLD 23 LUB
Enforce VSL-35-7 >= 1/2" CLD 23 LUB
Enforce VSL-45 >= 1/2" CLD 23 LUB
Enforce VSL-45-2 >= 1/2" CLD 23 LUB
Enforce VSL-45-5 >= 1/2" CLD 23 LUB
Enforce VSL-45-6 >= 1/2" CLD 23 LUB
Enforce VSL-45-7 >= 1/2" CLD 23 LUB
Nepro >= 1/2" CLD 23 LUB
Polylube >= 1/2" CLD 23 LUB
Polylube Ultra >= 1/2" CLD 23 LUB
VSL-18 >= 1/2" CLD 23 LUB
VSL-35 >= 1/2" CLD 23 LUB
VSL-35-2 >= 1/2" CLD 23 LUB
VSL-35-5 >= 1/2" CLD 23 LUB
VSL-35-6 >= 1/2" CLD 23 LUB
VSL-35-7 >= 1/2" CLD 23 LUB
VSL-45 >= 1/2" CLD 23 LUB
VSL-45-2 >= 1/2" CLD 23 LUB
VSL-45-5 >= 1/2" CLD 23 LUB
VSL-45-6 >= 1/2" CLD 23 LUB
VSL-45-7 >= 1/2" CLD 23 LUB



 
Indumar Products, Inc. 
3355 West Alabama
Suite 110 
Houston, TX 77098 
United States 
800-523-7867 
713-977-4100
Visit this company's website

Facility : Houston, TX

Joining and Sealing Materials

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Sealants
FIXSTIX® Epoxy [1] C. HOT EPOXY

[1] The exposed surface area of each sealant in a household distribution system should not
    exceed 1.8 sq. cm./L or 0.2 sq. in./L.



 
Inertech, Inc. 
641 Monterey Pass Road
Monterey Park, CA 91754 
United States 
800-463-7839 
626-282-2000
Visit this company's website

Facility : Taichung, Taiwan

Joining and Sealing Materials

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Gasket/Sealing Materials[1]
Inertex SQ-S Expanded PTFE Gasket Sheet [2] C. HOT PTFE

[1] Certified for use in Mechanical Plumbing Device applications with a maximum use
    restriction of 2 sq. in./L.
[2] Certified for a maximum surface area to volume ratio of 2 sq. in./L.



 
Inpac, LLC 
2904 East 19th Street
Texarkana, AR 71854 
United States 
870-773-1339
Visit this company's website

Facility : Taipei, Taiwan

Joining and Sealing Materials

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Gasket/Sealing Materials
INPAC NBR 60 [1] CLD 23 NBR
INPAC NBR 75 [2] CLD 23 NBR
INPAC SBR 60 [3] CLD 23 SBR
INPAC SBR 75 [4] CLD 23 SBR
Inpac EPDM 60 [2] CLD 23 EPDM
Inpac EPDM 75 [2] CLD 23 EPDM

[1] Certified for a maximum surface area to volume ratio of 1.0 sq. in./L.
[2] Certified for a maximum surface area to volume ratio of 2.0 sq. in./L.
[3] Certified for a maximum surface area to volume ratio of 0.8 sq. in./L.
[4] Certified for a maximum surface area to volume ratio of 0.5 sq. in./L.



 
Interline Brands Inc. 
801 West Bay Street
Jacksonville, FL 32204 
United States 
904-421-1400

Facility : Elk Grove Village, IL

Joining and Sealing Materials

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Brazing/Solders/Fluxes[G]
ProPlus Soldering Paste >= 1/2" C. HOT FLX

[G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for
    “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state
    laws and the U.S. Safe Drinking Water Act.

    

Thread Compounds[G]
Premier Blue Seal Thread Sealant >= 1/2" C. HOT TC

[G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for
    “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state
    laws and the U.S. Safe Drinking Water Act.

    



 
Internationale Metall Imprägnier GmbH 
International Metal Impregnating Co Ltd
Daimlerstrasse 12 
D-40789 Monheim Am Rhein 
Germany 
49 2173 9260
Visit this company's website

Facility : # 2 Germany

Joining and Sealing Materials

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Sealants
IM 3000 [1] [2] [3] [4] C. HOT MLTPL
IM4500r [1] [2] [3] [4] C. HOT MLTPL
IM7000 [1] [2] [3] [4] C. HOT MLTPL

[1] Certified for a maximum surface area to volume ratio of 50 square inches per liter.
[2] Impregnation allowable on castings exhibiting a maximum leakage of 450 cc's when tested
    at 60 PSI air pressure.
[3] Also evaluated as material for use in Mechanical Plumbing Devices (Section 9) for
    applications with a maximum surface area of 50 square inches per liter.
[4] Certified for use in materials with a porosity rating of less than 1 percent.



 
IPS Adhesives (Jiashan) Co., Ltd. 
11 Binjiang Road
Jiashan Economic Development Zone 
Zhejiang 314100 
China 
86 573 8425 2258
Visit this company's website

Facility : Zhejiang, China

Joining and Sealing Materials

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Primers
Weld-On® P-68™ Clear Low- VOC CPVC/PVC Primer >= 1/2" C. HOT NA
Weld-On® P-70™ Clear or Purple Low-VOC CPVC/PVC Primer >= 1/2" C. HOT NA

Solvent Cements
Weld-On® 2713™ Yellow Low-VOC One Step CPVC Cement >= 1/2" C. HOT NA
Weld-On® 605 Clear Low VOC PVC Cement[1] >= 1/2" CLD 23 NA
Weld-On® 711 Gray Low VOC PVC[1] >= 1/2" CLD 23 NA
Weld-On® 714 Gray Low VOC CPVC[1] >= 1/2" C. HOT NA
Weld-On® 714 Orange Low VOC CPVC[1] >= 1/2" C. HOT NA
Weld-On® 717 Clear Low VOC PVC[1] >= 1/2" CLD 23 NA
Weld-On® 717 Gray Low VOC PVC[1] >= 1/2" CLD 23 NA
Weld-On® 717 White Low VOC PVC[1] >= 1/2" CLD 23 NA
Weld-On® 719 Clear Low VOC PVC [1] >= 1/2" CLD 23 NA
Weld-On® 719 Gray Low VOC PVC [1] >= 1/2" CLD 23 NA
Weld-On® 719 White Low VOC PVC [1] >= 1/2" CLD 23 NA
Weld-On® 724 Gray CPVC Low-VOC[1] >= 1/2" C. HOT NA
Weld-On® 727™ Clear PVC Low-VOC[1] >= 1/2" CLD 23 NA
Weld-On® 727™ Clear PVC “Hot ‘R Cold”™ Low-VOC[1] >= 1/2" CLD 23 NA
Weld-On® 747™ Blue PVC Low-VOC[1] >= 1/2" CLD 23 NA
Weld-On® Flowguard Gold® Low-VOC One Step CPVC Cement >= 1/2" C. HOT NA

[1] Certified for use with Weld-On® P-68 Clear Low-VOC Primer for PVC/CPVC, Weld-On® P-70
    Clear Low-VOC CPVC/PVC Primer, or Weld-On® P-70 Purple Low-VOC CPVC/PVC Primer.



IPS Corporation 
202 Industrial Park Lane
P.O. Box 220 
Collierville, TN 38027 
United States 
800-489-4848 
Visit this company's website

Facility : # 1 USA

Joining and Sealing Materials

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Lubricants
EZ Flush Pipe Lubricant >= 1/2" CLD 23 LUB

Thread Compounds
ALL Seal Pipe Joint Compound >= 1/2" C. HOT TS
Blue Seal Pipe Joint Compound >= 1/2" C. HOT TS
Gold Seal Pipe Joint Compound >= 1/2" C. HOT TS
White Seal Plus >= 1/2" C. HOT TS



 
IPS Corporation 
17109 South Main
P.O. Box 379 
Gardena, CA 90248 
United States 
310-898-3351
Visit this company's website

Facility : Gardena, CA

Joining and Sealing Materials

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Primers [G]
Weld-On 738™ HOT'N FAST™[4] [G] >= 1/2" CLD 23 NA
Weld-On P-68 Clear Low-VOC CPVC/PVC Primer >= 1/2" C. HOT NA
Weld-On P-68 Purple Low-VOC CPVC/PVC Primer >= 1/2" C. HOT NA
Weld-On P-70 Clear Low-VOC CPVC/PVC Primer >= 1/2" C. HOT NA
Weld-On P-70 Primer Purple Low VOC >= 1/2" C. HOT NA
Weld-On P-70 Purple Low-VOC CPVC/PVC Primer >= 1/2" C. HOT NA
Weld-On P-72 Clear Primer >= 1/2" C. HOT NA
Weld-On P-75 Aqua Blue Low-VOC "Wet 'R Dry" >= 1/2" CLD 23 NA
Weld-On Plumbing Primer Low VOC Clear >= 1/2" C. HOT NA
Weld-On Plumbing Primer Low VOC Purple >= 1/2" C. HOT NA
Weld-On Pool Primer Clear or Purple >= 1/2" C. HOT NA

[4] The compliance of this product with the health effect requirements of NSF/ANSI Standard
    61 was determined based on the testing of pipe and fittings assembled using the cement
    and P-75 Aqua-Blue Low VOC primer.
[G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for
    “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state
    laws and the U.S. Safe Drinking Water Act.

    
[G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for
    “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state
    laws and the U.S. Safe Drinking Water Act.

    

Solvent Cements
WELD-ON FLOWGUARD 714 CPVC CEMENT ORANGE HEAVY BODIED[1] [G] >= 1/2" C. HOT NA
Weld-On 2700 Clear PVC[1] [G] >= 1/2" CLD 23 NA
Weld-On 2704 Clear or Gray Low-VOC PVC[1] [G] >= 1/2" CLD 23 NA
Weld-On 2705 Clear or Gray Low-VOC PVC[G] >= 1/2" CLD 23 NA
Weld-On 2711 Gray PVC[1] [G] >= 1/2" CLD 23 NA
Weld-On 2713 Green CPVC[G] >= 1/2" C. HOT NA
Weld-On 2714 Beige Low-VOC CPVC[G] >= 1/2" C. HOT NA
Weld-On 2714 Gray or Orange Low-VOC CPVC[1] [G] >= 1/2" C. HOT NA
Weld-On 2714 Red or Tan Low-VOC CPVC[G] >= 1/2" C. HOT NA
Weld-On 2714 Yellow Low-VOC CPVC[1] [G] >= 1/2" C. HOT NA
Weld-On 2717 Clear, Gray, or White Low-VOC PVC[G] >= 1/2" CLD 23 NA
Weld-On 2721 Blue Low-VOC PVC[1] [G] >= 1/2" CLD 23 NA
Weld-On 2721 Clear Low-VOC PVC "Wet 'R Dry"[1] [G] >= 1/2" CLD 23 NA
Weld-On 2725 Clear Low-VOC PVC "Wet 'R Dry"[1] [G] >= 1/2" CLD 23 NA
Weld-On 2735 Blue Low-VOC PVC[1] [G] >= 1/2" CLD 23 NA
Weld-On 3503 Clear PVC[1] [G] >= 1/2" CLD 23 NA
Weld-On 3550[1] [G] >= 1/2" CLD 23 NA
Weld-On 3551[1] [G] >= 1/2" CLD 23 NA
Weld-On 3555[G] >= 1/2" C. HOT NA
Weld-On 3556 CPVC Cement Yellow Low VOC[G] >= 1/2" C. HOT NA
Weld-On 3563 Orange Low-VOC[1] [G] >= 1/2" C. HOT NA
Weld-On 3563 Yellow Low-VOC CPVC[1] [G] >= 1/2" C. HOT NA
Weld-On 3567 Clear PVC Cement[1] [G] >= 1/2" CLD 23 NA
Weld-On 3567 Gray PVC Cement[1] [G] >= 1/2" CLD 23 NA
Weld-On 617 PVC-U CONSTRUCTION Clear[1] [G] >= 1/2" CLD 23 NA
Weld-On 617 PVC-U CONSTRUCTION Gray[1] [G] >= 1/2" CLD 23 NA
Weld-On 700 Clear Low VOC[1] [G] >= 1/2" CLD 23 NA
Weld-On 700 Clear PVC[1] [G] >= 1/2" CLD 23 NA
Weld-On 702 Clear PVC[1] [G] >= 1/2" CLD 23 NA
Weld-On 704 Clear/Gray/White Low-VOC PVC[1] [G] >= 1/2" CLD 23 NA
Weld-On 705 Clear, Gray, or White Low-VOC PVC[G] >= 1/2" CLD 23 NA
Weld-On 706 White PVC[1] [G] >= 1/2" CLD 23 NA
Weld-On 711 Gray/White Low-VOC[1] [G] >= 1/2" CLD 23 NA
Weld-On 713 Orange Low-VOC CPVC[G] >= 1/2" C. HOT NA
Weld-On 714 Orange Low-VOC CPVC[1] [G] >= 1/2" C. HOT NA
Weld-On 714 Orange or Gray CPVC[1] [G] >= 1/2" C. HOT NA
Weld-On 717 Clear, Gray, or White PVC[1] [G] >= 1/2" CLD 23 NA
Weld-On 717 Clear/Gray Low-VOC PVC[G] >= 1/2" CLD 23 NA
Weld-On 717XG Clear Low VOC Heavy-Body PVC Cement[G] >= 1/2" CLD 23 NA
Weld-On 721 Blue, or Green PVC[1] [G] >= 1/2" CLD 23 NA
Weld-On 724 Gray or Orange CPVC[3] [G] >= 1/2" C. HOT NA
Weld-On 724 Mustard Yellow CPVC[1] [G] >= 1/2" C. HOT NA
Weld-On 724 Yellow CPVC[1] [G] >= 1/2" C. HOT NA
Weld-On 727 Clear PVC "Hot 'R Cold"[1] [G] >= 1/2" CLD 23 NA
Weld-On 740™ POOL REG LOW VOC Clear[1] [G] >= 1/2" CLD 23 NA
Weld-On 744™ POOL MED CLEAR Low VOC PVC[1] [G] >= 1/2" CLD 23 NA
Weld-On 744™ POOL MED GRAY Low VOC PVC[1] [G] >= 1/2" CLD 23 NA
Weld-On 746™ POOL HVY Clear Low VOC[G] >= 1/2" CLD 23 NA
Weld-On 746™ POOL HVY Gray Low VOC[G] >= 1/2" CLD 23 NA
Weld-On 750 Hot-Weld[1] [G] >= 1/2" CLD 23 NA
Weld-On 795 Clear/Blue Low-VOC PVC[1] [G] >= 1/2" CLD 23 NA
Weld-On 917 Clear Low VOC Heavy-Body PVC Cement[G] >= 1/2" CLD 23 NA
Weld-On Low-VOC Flowguard Gold 1-Step CPVC[G] >= 1/2" C. HOT NA
Weld-On® 2713™ Yellow Low-VOC One Step CPVC Cement[G] >= 1/2" C. HOT NA
Weld-On® 2725™ Blue Low-VOC PVC Wet 'R Dry™[4] [G] >= 1/2" CLD 23 NA
Weld-On® 2737™ Blue Low-VOC PVC Hot 'N Fast™[4] [G] >= 1/2" CLD 23 NA
Weld-On® 2747™ Blue Low-VOC PVC Pool 'R Spa™[1] [G] >= 1/2" CLD 23 NA
Weld-On® 3553 Low-VOC PVC[1] [G] >= 1/2" CLD 23 NA
Weld-On® 3555™ Yellow Low-VOC One Step CPVC Cement[G] >= 1/2" C. HOT NA
Weld-On® 602 Clear Low VOC PVC Regular Bodied PVC Cement[G] >= 1/2" CLD 23 NA
Weld-On® 605 Clear Low VOC PVC Cement[G] >= 1/2" CLD 23 NA
Weld-On® 605 Clear Low VOC PVC-U Construction[G] >= 1/2" CLD 23 NA
Weld-On® 710 Clear Low-VOC PVC[1] [G] >= 1/2" CLD 23 NA
Weld-On® 719 Clear, Gray, or White Low-VOC PVC[1] [G] >= 1/2" CLD 23 NA
Weld-On® 725™ Wet 'R Dry™ Low-VOC[4] [G] >= 1/2" CLD 23 NA
Weld-On® 735™ Wet 'N Fast™ Low-VOC[4] [G] >= 1/2" CLD 23 NA
Weld-On® 737™ Turf 'N Ag™ Low-VOC[4] [G] >= 1/2" CLD 23 NA
Weld-On® 747™ Blue PVC Pool 'R Spa™[1] [G] >= 1/2" CLD 23 NA
Weld-On® 748™ Pool Fast™ Low-VOC[4] [G] >= 1/2" CLD 23 NA
Weld-On® 798™ Pool Flex™[1] [G] >= 1/2" CLD 23 NA
Weld-On® 919 Clear Low VOC[1] [5] >= 1/2" CLD 23 NA
Weld-On® Blazemaster®[G] >= 1/2" C. HOT NA
Weld-On® Flowguard Gold® Low-VOC One Step CPVC Cement[G] >= 1/2" C. HOT NA
Weld-On® Flowguard® Glow Low-VOC CPVC Cement[G] >= 1/2" C. HOT NA
Weld-on 2795 Blue or Clear Low-VOC PVC[1] [G] >= 1/2" CLD 23 NA

[1] The compliance of this product with the health effect requirements of NSF/ANSI Standard
    61 was determined based on the testing of pipe and fittings assembled using the cement
    and either Weld-On P-68 and P-70 Clear or Purple Primers.
[3] The compliance of this product with the health effect requirements of NSF/ANSI Standard
    61 was determined based on the testing of pipe and fittings assembled using the cement
    and Weld-On P-72 Clear Primer.
[4] The compliance of this product with the health effect requirements of NSF/ANSI Standard
    61 was determined based on the testing of pipe and fittings assembled using the cement
    and P-75 Aqua-Blue Low VOC primer.
[5] Weld-On® 919 Clear Low VOC may be applied without primer or with either Weld-On® P-68™
    Clear or Purple Primer or P-70™ Clear or Purple Primer.
[G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for
    “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state
    laws and the U.S. Safe Drinking Water Act.

    

[2] The compliance of this product with the health effect requirements of NSF/ANSI Standard
    61 was determined based on the testing of pipe and fittings assembled using the cement
    and either Weld-On® P-68 Clear or Purple, P-70® Clear or Purple, or P-72 Clear Primers.


 
ISPO AG 
Eichtalboden 5H
Baden 5400 
Switzerland 
41 56 210 9293

Facility : # 1 Switzerland

Joining and Sealing Materials

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Adhesives
ISPO CYANO UNIVERSAL >= 1/2" C. HOT ADH



 
ITW Chemical Products Scandinavia Aps 
Priorsvej 36
8600 Silkeborg 
Denmark 
45 86 82 64 44

Facility : # 1 Europe

Joining and Sealing Materials

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Adhesives
Kemlock AL-03 >= 1/2" C. HOT ADH
Kemlock AL-38 >= 1/2" C. HOT ADH
Kemlock AP-74 >= 1/2" C. HOT ADH
Kemlock AS-43 >= 1/2" C. HOT ADH
Kemlock AS-70 >= 1/2" C. HOT ADH
Kemlock AS-75 >= 1/2" C. HOT ADH

Sealants
Kemlock AP-73 >= 1/2" C. HOT SLT

Thread Compounds
Kemlock AS-70 >= 1/2" C. HOT TC
Kemlock AT-72 >= 1/2" C. HOT TC
Kemlock AT-77[1] >= 1/2" C. HOT TC

[1] Certification is based on a minimum cure of 72 hours at 75°F.



 
ITW Chemische Produkte GmbH & Co. KG 
Mühlacker Strasse 149
D-75417 Mülacker 
Germany 
49 704 196 3419

Facility : # 1 Europe

Joining and Sealing Materials

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Adhesives
VA 12-42 >= 1/2" C. HOT ADH
VA 12-43 >= 1/2" C. HOT ADH
VA 12-45 >= 1/2" C. HOT ADH
VA 12-62 >= 1/2" C. HOT ADH
VA 12-70 >= 1/2" C. HOT ADH
VA 12-71 >= 1/2" C. HOT ADH
VA 15-74 >= 1/2" C. HOT ADH
VA 16-03 >= 1/2" C. HOT ADH
VA 16-38 >= 1/2" C. HOT ADH
VA 16-48 >= 1/2" C. HOT ADH

Sealants
VA 15-73 >= 1/2" C. HOT SLT

Thread Compounds
VA 12-62 >= 1/2" C. HOT TC
VA 12-70 >= 1/2" C. HOT TC
VA 12-71 >= 1/2" C. HOT TC
VA 15-72 >= 1/2" C. HOT TC
VA 15-77[1] >= 1/2" C. HOT TC
VA 15-86 >= 1/2" C. HOT TC

[1] Certification is based on a minimum cure of 72 hours at 75°F.



 
ITW Polymers Adhesives, North America 
30 Endicott Street
Danvers, MA 01923 
United States 
978-777-1100
Visit this company's website

Facility : Danvers, MA

Joining and Sealing Materials

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Patching Materials [G]
Devcon Stainless Steel Putty [1] CLD 23 SSEP

[1] Certified for use up to 10% of the surface area in tanks 100 gallons and greater.
[G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for
    “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state
    laws and the U.S. Safe Drinking Water Act.

    



 
ITW Polymers Coatings North America 
130 Commerce Drive
Montgomeryville, PA 18936 
United States 
215-855-8450

Facility : Houston, TX

Joining and Sealing Materials

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Sealants
THIOKOL® 2235 M [1] CLD 23 PSU

[1] Certified for a maximum use of 1% of a 2,000,000 gallon tank or greater.



 
ITW Red Head 
700 High Grove Boulevard
Glendale Heights, IL 60139 
United States 
800-348-3231 
630-825-7900
Visit this company's website

Facility : Elk Grove Village, IL

Joining and Sealing Materials

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Adhesives
Epcon A7 Adhesive [1] CLD 23 ACR
Epcon C6 Epoxy[2] [1] CLD 23 EPOXY
Epcon G5 [1] CLD 23 EPOXY
Epcon S7 [1] CLD 23 VE

[1] Certified for use at a maximum surface area to volume ratio of 0.0005 sq. in./L in a
    tank.
[2] Only products bearing the NSF Mark on the product, product packaging, and/or
    documentation shipped with the product are Certified.



 
J C Whitlam Mfg Company 
200 West Walnut Street
P.O. Box 380 
Wadsworth, OH 44282 
United States 
330-334-2524

Facility : Wadsworth, OH

Joining and Sealing Materials

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Lubricants[G]
Blue Lube Gasket Paste >= 1/2" CLD 23 LUB
Gasket Lube Paste >= 1/2" CLD 23 LUB
Pipe Slime Gasket Lube >= 1/2" D. HOT LUB

[G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for
    “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state
    laws and the U.S. Safe Drinking Water Act.

    

Primers[G]
Whitlam Low-VOC Clear Primer >= 1/2" CLD 23 NA
Whitlam Low-VOC Purple Primer >= 1/2" CLD 23 NA

[G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for
    “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state
    laws and the U.S. Safe Drinking Water Act.

    

Sealants[G]
Blue Magic Industrial Grade Pipe Joint Cmpd >= 1/2" C. HOT NA
Select-Unyte >= 1/2" C. HOT NA
T-U Type 555 >= 1/2" C. HOT NA

[G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for
    “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state
    laws and the U.S. Safe Drinking Water Act.

    

Solvent Cements [G]
Pro-Green Irrigation Cement[1] >= 1/2" CLD 23 NA
Shark Bite PVC Cement[1] >= 1/2" CLD 23 NA
Turf-Pool & Repair Cement[1] >= 1/2" CLD 23 NA
Whitlam Low VOC Clear or Gray Heavy Body Cement PVC[1] >= 1/2" CLD 23 NA
Whitlam Low VOC Clear or Gray Medium Body Cement[1] >= 1/2" CLD 23 NA
Whitlam Low VOC Clear or Gray Regular Body Cement[1] >= 1/2" CLD 23 NA
Whitlam Weatherproof 1 Step Low VOC Medium PVC Cement[1] >= 1/2" CLD 23 NA

[1] The compliance of this product with the health effects requirements of NSF/ANSI Standard
    61 is evaluated based on pipe and fittings assembled using the cement and Whitlam
    Low-VOC Clear or Purple Primer.
[G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for
    “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state
    laws and the U.S. Safe Drinking Water Act.

    



 
J-B Weld Company 
P.O. Box 483
Sulphur Springs, TX 75483 
United States 
903-855-7696

Facility : # 1 USA

Joining and Sealing Materials

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Patching Materials
J-B STIK [1] C. HOT EPOXY
PlasticWeld [1] C. HOT EPOXY
SteelStick [1] C. HOT EPOXY
WaterWeld [1] C. HOT EPOXY

[1] The exposed surface area of each sealant in a household distribution system shall not
    exceed 1.3 sq. cm/L or .2 sq. in./L.



 
J. W. Harris Co. Inc. DBA The Harris Products Group 
4501 Quality Drive
Mason, OH 45040 
United States 
513-754-6122

Facility : Mason, OH

Joining and Sealing Materials

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Brazing/Solders/Fluxes [G]
95/5[1] >= 1/2" C. HOT SLDR
Lead-Free Bridgit Nickel Bearing Solder[1] >= 1/2" C. HOT SLDR
Nick Lead-Free Solder[1] >= 1/2" D. HOT SLDR
Stay Brite[1] >= 1/2" C. HOT SLDR
Stay Brite Ultra[1] >= 1/2" C. HOT SLDR

[1] Maximum weld width of 1/4".
[G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for
    “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state
    laws and the U.S. Safe Drinking Water Act.

    

Fluxes[G]
Bridgit Soldering Flux >= 1/2" C. HOT FLX
Bridgit Water Soluable Flux >= 1/2" C. HOT FLX

[G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for
    “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state
    laws and the U.S. Safe Drinking Water Act.

    



 
J.C. Whitlam Manufacturing Company 
200 West Walnut Street
Wadsworth, OH 44281 
United States 
330-334-2524

Facility : # 1 USA

Joining and Sealing Materials

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Lubricants
Quick Slip Plus Pipe Joint Lubricant[G] >= 1/2" CLD 23 LUB

[G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for
    “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state
    laws and the U.S. Safe Drinking Water Act.

    



 
Jasper Rubber Products, Inc. 
1010 First Avenue
Jasper, IN 47546 
United States 
800-457-7457 
812-482-3242

Facility : Jasper, IN

Joining and Sealing Materials

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Gasket/Sealing Materials
MF 6087 70 EPDM Peroxide Cure[G] [1] [2] C. HOT EPDM
MF 6174 80 EPDM Peroxide Cure [1] D. HOT EPDM
MF 6362 70 EPDM Peroxide Cure[G] [1] [2] C. HOT EPDM
MF 6363 80 EPDM Peroxide Cure [1] D. HOT EPDM

[1] Certified for a maximum surface area to volume ratio of 2.0 sq. in./L.
[2] This product also has been evaluated for use in Mechanical Plumbing Device applications
    with a maximum use restrictions of 0.2 sq.in./L.
[G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for
    “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state
    laws and the U.S. Safe Drinking Water Act.

    



 
Jet-Lube, Inc. 
4849 Homestead Road
Suite 232 
Houston, TX 77028 
United States 
800-538-5823 
713-670-5700

Facility : Houston, TX

Joining and Sealing Materials

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Thread Compounds
Eco-Safe[G] [1] CLD 23 TC
V-2 Multipurpose Thread Sealant with PTFE[G] [2] C. HOT TS
Well Guard[G] [1] CLD 23 TC

[1] Evaluated for use as a thread compound in:
    Drill collars/tool joints >=4 1/2"
    Tubing >=2 3/8"
    Well casings >=4 1/2"
[2] Certified for use on pipes 1/2" and greater.
[G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for
    “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state
    laws and the U.S. Safe Drinking Water Act.

    



 
Jinan Kinger Pipeline Corp. 
Room 1102, YongAn Plaza
No. 268 QuanCheng Road 
Jinan, Shandong Province 250001 
China 
86 531 8191 3333
Visit this company's website

Facility : Shandong Province, China

Joining and Sealing Materials

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Gasket/Sealing Materials[1]
SBR JK1006 MJ Transition Gasket 2" - 48" CLD 23 SBR
SBR JK1006 Mechanical Joint Gasket 2" - 48" CLD 23 SBR

[1] Certified for use in distribution systems, with width exposure of no more than 1/2" in
    pipes with diameters shown in "size".



 
JIT Silicones + a Division of Sensible Components, LLC 
P.O. Box 6501
Clearwater, FL 33758-6501 
United States 
855-548-7587

Facility : # 5 USA

Joining and Sealing Materials

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Lubricants
Valve Sealing Lubricant >= 1/2" C. HOT SLC



 
JK Polysource 
1241 East Glendale Avenue
Sparks, NV 89431 
United States 
800-526-0035 
775-323-7117

Facility : Fort Wayne, IN

Joining and Sealing Materials

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Gasket/Sealing Materials
PS 55 IR/SBR-MB [1] CLD 23 MLTPL

[1] Certified for use in pipes 6" and greater.  Certification is for gasket only.

O-Rings
PS 55 IR/SBR-MB [1] CLD 23 MLTPL

[1] Certified for use in pipes 6" and greater.  Certification is for gasket only.



 
Joseph Dresselhaus Befestigungstechnik GmbH & Co. KG 
Zeppelinstrasse 13
32051 Herford 
Germany 
49 522 193 2232
Visit this company's website

Facility : # 1 Switzerland

Joining and Sealing Materials

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Adhesives
activ 91 >= 1/2" C. HOT ADH
activ 92 >= 1/2" C. HOT ADH
activ 93 >= 1/2" C. HOT ADH
activ 94 >= 1/2" C. HOT ADH

Thread Compounds
activ 90 >= 1/2" C. HOT TC



 
JP Specialties, Inc. / Earth Shield Waterstop 
25811 Jefferson Avenue
Murrieta, CA 92562 
United States 
800-821-3859 
951-763-7077
Visit this company's website

Facility : Murrieta, CA

Joining and Sealing Materials

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Waterstop
Earth Shield® Waterstop [1] CLD 23 TPE
Earth Shield® Waterstop part no. JP1149 [1] CLD 23 TPE
Earth Shield® Waterstop part no. JP1225 [1] CLD 23 TPE
Earth Shield® Waterstop part no. JP158 [1] CLD 23 TPE
Earth Shield® Waterstop part no. JP211 [1] CLD 23 TPE
Earth Shield® Waterstop part no. JP320L [1] CLD 23 TPE
Earth Shield® Waterstop part no. JP325T [1] CLD 23 TPE
Earth Shield® Waterstop part no. JP336L [1] CLD 23 TPE
Earth Shield® Waterstop part no. JP436 [1] CLD 23 TPE
Earth Shield® Waterstop part no. JP450T [1] CLD 23 TPE
Earth Shield® Waterstop part no. JP500 [1] CLD 23 TPE
Earth Shield® Waterstop part no. JP540L [1] CLD 23 TPE
Earth Shield® Waterstop part no. JP621L [1] CLD 23 TPE
Earth Shield® Waterstop part no. JP636 [1] CLD 23 TPE
Earth Shield® Waterstop part no. JP647 [1] CLD 23 TPE
Earth Shield® Waterstop part no. JP648 [1] CLD 23 TPE
Earth Shield® Waterstop part no. JP678 [1] CLD 23 TPE
Earth Shield® Waterstop part no. JP936 [1] CLD 23 TPE
Earth Shield® Waterstop part no. JP948 [1] CLD 23 TPE
Earth Shield® Waterstop part no. JP949 [1] CLD 23 TPE
Earth Shield® Waterstop part no. JP978 [1] CLD 23 TPE
Earth Shield® Waterstop part no. JPEB350 [1] CLD 23 TPE
Earth Shield® Waterstop part no. JPEB375 [1] CLD 23 TPE
Earth Shield® Waterstop part no. JPEB375R [1] CLD 23 TPE

[1] This material is approved as a waterstop for use in any potable water treatment or
    retaining structure.



 
JTM Products, Inc. 
31025 Carter Street
Solon, OH 44139-3521 
United States 
800-229-6744 
440-287-2302

Facility : Solon, OH

Joining and Sealing Materials

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Lubricants
#88-6 Pipe Joint Lubricant[G] >= 1/2" CLD 23 LUB
11-4[G] >= 1/2" CLD 23 LUB
27-A[G] >= 1/2" CLD 23 LUB
27-A Pipe Joint Lubricant[G] >= 1/2" CLD 23 LUB
27-XL Pipe Joint Lubricant[G] >= 1/2" CLD 23 LUB
27A[G] >= 1/2" CLD 23 LUB
77-315 Pipe Joint Lubricant[G] >= 1/2" CLD 23 LUB
88-6[G] >= 1/2" CLD 23 LUB
American Fastite Joint Lubricant[G] >= 1/2" CLD 23 LUB
Concord Pipe Joint Lubricant[G] >= 1/2" CLD 23 LUB
Dymalube 10[G] >= 1/2" CLD 23 LUB
DynaLube 10[G] >= 1/2" CLD 23 LUB
Ease-On Pipe Joint Lubricant[G] >= 1/2" CLD 23 LUB
PermaLynx[G] >= 1/2" CLD 23 LUB
Phoenix 27-XL Pipe Joint Lubricant[G] >= 1/2" CLD 23 LUB
Phoenix Aqua 20 Pipe Joint Lubricant[G] >= 1/2" CLD 23 LUB
Phoenix Water Dispersible Pipe Joint Lubricant[G] >= 1/2" CLD 23 LUB
Phoenix Water Dispersible Type 27A Pipe Joint Lubricant[G] >= 1/2" CLD 23 LUB
Press Seal Regular Lube[G] >= 1/2" CLD 23 LUB
Price Brothers Pipe Joint Lubricant Type E-O[G] >= 1/2" CLD 23 LUB
Royal Seal[G] >= 1/2" CLD 23 LUB
Shurjoint[G] >= 1/2" CLD 23 LUB
TYTON JOINT® Lubricant[G] >= 1/2" CLD 23 LUB
Water Dispersible Pipe Joint Lubricant[G] >= 1/2" CLD 23 LUB

[G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for
    “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state
    laws and the U.S. Safe Drinking Water Act.

    



 
Kapp Alloy and Wire, Inc. 
1Klein Street
P.O. Box 1188 
Oil City, PA 16301-0688 
United States 
800-327-6533 
814-676-0613
Visit this company's website

Facility : Oil City, PA

Joining and Sealing Materials

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Brazing/Solders/Fluxes [G]
KappZapp™ [1] C. HOT SLDR
KappZapp™ 3.5 [1] C. HOT SLDR
KappZapp™ 4 [1] C. HOT SLDR
KappZapp™ 5 [1] C. HOT SLDR
KappZapp™ 6 [1] C. HOT SLDR
KappZapp™ 7 [1] C. HOT SLDR

[1] Certified for use with pipe sizes 1/2" and greater.
[G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for
    “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state
    laws and the U.S. Safe Drinking Water Act.

    



 
KIC Krones Internationale Cooperationsgesellschaft Mbh 
Böhmerwaldstrasse 5
93073 Neutraubling 
Germany 
49 9401 70 2372

Facility : A Germany

Joining and Sealing Materials

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Lubricants[G]
Krones-celerol L 7001 >= 1/2" C. HOT LUB
Krones-celerol L 7001 BR >= 1/2" C. HOT LUB

[G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for
    “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state
    laws and the U.S. Safe Drinking Water Act.

    



 
Kirkhill 
12023 Woodruff Avenue
Downey, CA 90241 
United States 
562-803-1117
Visit this company's website

Facility : Downey, CA

Joining and Sealing Materials

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Gasket/Sealing Materials[1]
80525 [2] CLD 23 MLTPL
Potable Water NBR [2] CLD 23 MLTPL
Potable Water SBR [2] CLD 23 MLTPL

[1] This product has also been evaluated for use in Mechanical Plumbing Device applications
    with a maximum use restriction of 1.5 sq. in./L.
[2] Certified for a maximum surface area to volume ratio of 2.0 sq. in./L.



 
Kisling AG 
Motorenstrasse 102
CH-8620 Wetzikon 
Switzerland 
41 58 272 0272

Facility : # 1 Switzerland

Joining and Sealing Materials

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Adhesives[1]
Ergo 4052 >= 1/2" C. HOT ADH
Ergo 4053 >= 1/2" C. HOT ADH
Ergo 4100 >= 1/2" C. HOT ADH
Ergo 4101 >= 1/2" C. HOT ADH
Ergo 4102 >= 1/2" C. HOT ADH
Ergo 4207 >= 1/2" C. HOT ADH
Ergo 4209 >= 1/2" C. HOT ADH
Ergo 4212 >= 1/2" C. HOT ADH
Ergo 4253 >= 1/2" C. HOT ADH
Ergo 4280[2] >= 1/2" C. HOT ADH
Ergo 4430 >= 1/2" C. HOT ADH
Ergo 4451 >= 1/2" C. HOT ADH
Ergo 4453 >= 1/2" C. HOT ADH
Ergo 5011 >= 1/2" C. HOT ADH
Ergo 5300 >= 1/2" C. HOT ADH
Ergo 5400 >= 1/2" C. HOT ADH
Ergo 5861 >= 1/2" C. HOT ADH
Ergo 5925 >= 1/2" C. HOT ADH

[1] Only products bearing the NSF Mark are NSF Certified.
[2] Certification is based on a minimum cure of 72 hours at 75ºF.

Sealants[1]
Ergo 4252 >= 1/2" C. HOT SLT

[1] Only products bearing the NSF Mark are NSF Certified.

Thread Compounds[1]
Ergo 4100 >= 1/2" C. HOT TC
Ergo 4101 >= 1/2" C. HOT TC
Ergo 4102 >= 1/2" C. HOT TC
Ergo 4205 >= 1/2" C. HOT TC
Ergo 4209 >= 1/2" C. HOT TC

[1] Only products bearing the NSF Mark are NSF Certified.



 
Klüber Lubrication München SE & Co. KG 
Geisenhausenerstrasse 7
D-81379 Munich 
Germany 
49 89 78760
Visit this company's website

Facility : Munich, Germany

Joining and Sealing Materials

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Lubricants [G]
022171 Unisilkon NCA 3001 [1] C. HOT LUB
Ideal Standard 12 [1] C. HOT LUB
Klubersynth UH1 64-2403 >= 1/2" C. HOT LUB
Klubersynth V 64-300 >= 1/2" C. HOT LUB
Klüberbeta VR 67-3500 >= 1/2" D. HOT LUB
Paraliq GTE 703 >= 1/2" C. HOT LUB
Testsample C1 >= 1/2" C. HOT LUB
UNISILKON LCA 3801 >= 1/2" C. HOT LUB
Unisilkon L 250L >= 1/2" C. HOT LUB
Unisilkon L 641 >= 1/2" C. HOT LUB

[1] The exposed surface area covered by this lubricant should not exceed the
     ratio of 0.6 sq. in./L.
[G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for
    “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state
    laws and the U.S. Safe Drinking Water Act.

    


Facility : EK

Joining and Sealing Materials

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Lubricants[G]
Klübersynth UH1 64-2403 >= 1/2" C. HOT LUB
Paraliq GTE 703 >= 1/2" C. HOT LUB
Unisilkon L 250L >= 1/2" C. HOT LUB

[G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for
    “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state
    laws and the U.S. Safe Drinking Water Act.

    


Facility : Barcelona, Spain

Joining and Sealing Materials

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Lubricants[G]
Klüberbeta VR 67-17002 >= 1/2" D. HOT LUB

[G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for
    “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state
    laws and the U.S. Safe Drinking Water Act.

    



 
KOK Machinery (Kunshan) Co. Ltd. 
#28 Bridge, Cao-An Road
Huaqiao Town, Kunshan City 
Jiangsu 215332 
China 
86 21 59566488
Visit this company's website

Facility : Jiangsu, China

Joining and Sealing Materials

    Water Water
    Contact Contact
Trade Designation Size Temp Material

O-Rings
CA-7510-A1K[2] [1] C. HOT EPDM
GE-705-C1K[3] [1] C. HOT SLC
HJC-710-K2K[4] [1] C. HOT FE
NBR-7010-AS3K [5] C. HOT NBR

[1] Certified for a maximum surface area to volume ratio of 2.0 sq. in./L.
[2] This product has also been evaluated for use in Mechanical Plumbing Device applications
    with a maximum use restriction of 1.5 sq. in./L.
[3] This product has also been evaluated for use in Mechanical Plumbing Device applications
    with a maximum use restriction of 2.0 sq. in./L.
[4] This product has also been evaluated for use in Mechanical Plumbing Device applications
    with a maximum use restriction of 0.2 sq. in./L.
[5] Certified for a maximum surface area to volume ratio of 0.6 sq. in./L.



 
La-Co Industries, Inc. 
1201 West Pratt Boulevard
Elk Grove Village, IL 60007-5746 
United States 
847-956-7600
Visit this company's website

Facility : Elk Grove Village, IL

Joining and Sealing Materials

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Thread Compounds[G]
Industrial Pipe Thread Paste - R >= 1/2" C. HOT TC
Leak-Tite Blue >= 1/2" C. HOT TC
Pipetite Stik >= 1/2" C. HOT TC
Slic-Tite Paste with PTFE >= 1" C. HOT TC
Slic-Tite Stick with PTFE >= 1" C. HOT TC
T-O-T Pipe Thread Compound >= 1/2" C. HOT TC

[G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for
    “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state
    laws and the U.S. Safe Drinking Water Act.

    

Brazing/Solders/Fluxes[G]
Flux-Rite 90 Paste >= 1/2" C. HOT FLX
Regular Flux Paste >= 1/2" C. HOT FLX
Silver Brazing Flux Paste >= 1/2" C. HOT FLX

[G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for
    “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state
    laws and the U.S. Safe Drinking Water Act.

    

Sealants[G]
Heat-Seal Stik® 2.0 sq. in./L C. HOT EPOXY

[G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for
    “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state
    laws and the U.S. Safe Drinking Water Act.

    



 
La-Co Industries, Inc. 
1201 West Pratt Boulevard
Elk Grove Village, IL 60007-5746 
United States 
800-621-4025 
847-956-7600

Facility : # 1 USA

Joining and Sealing Materials

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Lubricants[G]
Lubrijoint >= 1/2" CLD 23 LUB

[G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for
    “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state
    laws and the U.S. Safe Drinking Water Act.

    



 
La-Co Industries, Inc. 
1201 West Pratt Boulevard
Elk Grove Village, IL 60007-5746 
United States 
847-956-7600
Visit this company's website

Facility : # 2 USA

Joining and Sealing Materials

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Patching Materials
Epoxy-Stik [1] C. HOT EPOXY

[1] The exposed surface area of each sealant in a household distribution system should not
    exceed 1.3 sq. cm/L or .2 sq. in/L.



 
Lav. El. Gomma S.R.L. 
Via Also Moro, 20/22
25033 Cologne (BS) 
Italy 
39 030 7050956
Visit this company's website

Facility : Cologne (BS), Italy

Joining and Sealing Materials

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Gasket/Sealing Materials
01/AA70NBR[2] [3] CLD 23 NBR
01/AA80NBR[2] [3] CLD 23 NBR
01/B70NBR [1] C. HOT NBR
01/B80NBR [1] C. HOT NBR
01/C50VMQ[2] [3] C. HOT SLC
01/C60VMQ[2] [3] C. HOT SLC
01/C70VMQ[2] [3] C. HOT SLC
01/L50VMQ[2] [3] C. HOT SLC
01/L60VMQ[2] [3] C. HOT SLC
01/L70VMQ[2] [3] C. HOT SLC
01/M50VMQ[2] [3] C. HOT SLC
01/M60VMQ[2] [3] C. HOT SLC
01/M70VMQ[2] [3] C. HOT SLC
01/N50VMQ[2] [3] C. HOT SLC
01/N60VMQ[2] [3] C. HOT SLC
01/N70VMQ[2] [3] C. HOT SLC
01/T70FKM [4] C. HOT FE
01/U60EP[2] [3] C. HOT EPDM
01/U70EP[2] [3] C. HOT EPDM
01/U80EP[2] [3] C. HOT EPDM

[1] Certified for a maximum surface area to volume ratio of 0.75 sq. in./L.
[2] This product has also been evaluated for use in Mechanical Plumbing Device applications
    with a maximum use restriction of 2.0 sq. in./L.
[3] Certified for a maximum surface area to volume ratio of 2.0 sq. in./L.
[4] Certified for a maximum surface area to volume ratio of 0.5 sq. in./L.

O-Rings
01/AA70NBR[2] [3] CLD 23 NBR
01/AA80NBR[2] [3] CLD 23 NBR
01/B70NBR [1] C. HOT NBR
01/B80NBR [1] C. HOT NBR
01/C50VMQ[2] [3] C. HOT SLC
01/C60VMQ[2] [3] C. HOT SLC
01/C70VMQ[2] [3] C. HOT SLC
01/L50VMQ[2] [3] C. HOT SLC
01/L60VMQ[2] [3] C. HOT SLC
01/L70VMQ[2] [3] C. HOT SLC
01/M50VMQ[2] [3] C. HOT SLC
01/M60VMQ[2] [3] C. HOT SLC
01/M70VMQ[2] [3] C. HOT SLC
01/N50VMQ[2] [3] C. HOT SLC
01/N60VMQ[2] [3] C. HOT SLC
01/N70VMQ[2] [3] C. HOT SLC
01/T70FKM [4] C. HOT FE
01/U60EP[2] [3] C. HOT EPDM
01/U70EP[2] [3] C. HOT EPDM
01/U80EP[2] [3] C. HOT EPDM

[1] Certified for a maximum surface area to volume ratio of 0.75 sq. in./L.
[2] This product has also been evaluated for use in Mechanical Plumbing Device applications
    with a maximum use restriction of 2.0 sq. in./L.
[3] Certified for a maximum surface area to volume ratio of 2.0 sq. in./L.
[4] Certified for a maximum surface area to volume ratio of 0.5 sq. in./L.



 
Lavelle Industries, Inc. 
665 McHenry Street
Burlington, WI 53105 
United States 
262-757-2210
Visit this company's website

Facility : Burlington, WI

Joining and Sealing Materials

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Gasket/Sealing Materials
F35019 Chlorazone® Black[6] [1] C. HOT EPDM
F35304 Chlorazone® Red [1] C. HOT EPDM
F36025[2] [1] C. HOT EPDM
F36035[2] [1] C. HOT EPDM
F36308 Chlorazone®[3] [1] C. HOT EPDM
F37016[2] [1] C. HOT EPDM
F37018[4] [1] CLD 23 EPDM
F37028 [1] CLD 23 EPDM
F37300 Chlorazone®[3] [1] C. HOT EPDM
F38008[6] [1] CLD 23 EPDM
F38009[6] [1] CLD 23 EPDM
F38012 [1] CLD 23 EPDM
F38013 [1] CLD 23 EPDM
F38015 [1] CLD 23 EPDM
F39300 Chlorazone® Red[3] [1] C. HOT EPDM
F58102 White [1] C. HOT SBR
F58103 White [1] C. HOT SBR
F58205 Gray [1] C. HOT SBR
F58206 Gray [1] C. HOT SBR
F58305 Orange [1] C. HOT SBR
F58306 Orchid [1] C. HOT SBR
F58307 Pink [1] C. HOT SBR
F58308 Violet [1] C. HOT SBR
F58403 Light Blue [1] C. HOT SBR
F58404 Dark Blue [1] C. HOT SBR
F58405 Dark Purple [1] C. HOT SBR
F58406 Light Blue [1] C. HOT SBR
F58500 Brown [1] C. HOT SBR
F58502 Dark Brown [1] C. HOT SBR
F58503 Light Brown [1] C. HOT SBR
F58602 Dark Green [1] C. HOT SBR
F58603 Teal [1] C. HOT SBR
F58701 Yellow [1] C. HOT SBR
F95301[5] [1] CLD 23 BUTYL

[1] Certified for a maximum surface area to volume ratio of 2.0 sq. in./L.
[2] This product has also been evaluated for use in Mechanical Device applications with a
    maximum surface area to volume ratio of 2.0 sq. in./L.
[3] This product has also been evaluated for use in Mechanical Plumbing Device applications
    with a maximum surface area to volume ratio of 2.0 sq. in./L.
[4] This product has also been evaluated for use in Mechanical Plumbing Device applications
    with a maximum surface area to volume ratio of 0.4 sq. in./L.
[5] This product has also been evaluated for use in Mechanical Plumbing Device applications
    with a maximum surface area to volume ratio of 0.5 sq. in./L.
[6] This product has also been evaluated for use in Mechanical Plumbing Device applications
    with a maximum surface area to volume ratio of 1.0 sq. in./L.



 
Lenox 
1690 Lowery Street
Winston-Salem, NC 27101-5603 
United States 
800-334-5266 
336-777-8600

Facility : # 1 Canada

Joining and Sealing Materials

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Brazing/Solders/Fluxes[G]
Lenox Paste Flux >= 1/2" C. HOT FLX
Lenox Tinning Flux >= 1/2" C. HOT FLX
BernzOmatic Petroleum Based Flux >= 1/2" C. HOT FLX

[G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for
    “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state
    laws and the U.S. Safe Drinking Water Act.

    



 
Linhai G-Good Adhesives Co., Ltd. 
Shiniu Cun, Yanjiang Zhen
Linhai Shi, Zhejiang 
China 
86 576 8569 6612

Facility : Zhejiang, China

Joining and Sealing Materials

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Primers
BAILEY P-1030 Clear Water Thin PVC/CPVC Plastic Pipe Primer >= 1/2" CLD 23 NA
ERA P-1030 Clear Water Thin PVC/CPVC Plastic Pipe Primer >= 1/2" CLD 23 NA
G-GOOD P-1030 Clear Water Thin PVC/CPVC Plastic Pipe Primer >= 1/2" CLD 23 NA

Solvent Cements
BAILEY CPVC 8125 Grey Heavy Bodied Plastic Pipe Cement >= 1/2" C. HOT NA
BAILEY CPVC 8213 Yellow Medium Bodied Plastic Pipe Cement >= 1/2" C. HOT NA
BAILEY PVC 3011 Clear Medium Bodied Plastic Pipe Cement >= 1/2" CLD 23 NA
BAILEY PVC 5023 Clear Heavy Bodied Plastic Pipe Cement >= 1/2" CLD 23 NA
BAILEY PVC 5125 Gray Heavy Bodied Plastic Pipe Cement >= 1/2" CLD 23 NA
ERA CPVC 8125 Grey Heavy Bodied Plastic Pipe Cement >= 1/2" C. HOT NA
ERA CPVC 8213 Yellow Medium Bodied Plastic Pipe Cement >= 1/2" C. HOT NA
ERA PVC 3011 Clear Medium Bodied Plastic Pipe Cement >= 1/2" CLD 23 NA
ERA PVC 5023 Clear Heavy Bodied Plastic Pipe Cement >= 1/2" CLD 23 NA
ERA PVC 5125 Gray Heavy Bodied Plastic Pipe Cement >= 1/2" CLD 23 NA
G-GOOD CPVC 8125 Grey Heavy Bodied Plastic Pipe Cement >= 1/2" C. HOT NA
G-GOOD CPVC 8213 Yellow Medium Bodied Plastic Pipe Cement >= 1/2" C. HOT NA
G-GOOD PVC 3011 Clear Medium Bodied Plastic Pipe Cement >= 1/2" CLD 23 NA
G-GOOD PVC 5023 Clear Heavy Bodied Plastic Pipe Cement >= 1/2" CLD 23 NA
G-GOOD PVC 5125 Gray Heavy Bodied Plastic Pipe Cement >= 1/2" CLD 23 NA



 
LSP Products Group 
3689 Arrowhead Drive
Carson City, NV 89706 
United States 
775-884-4242

Facility : # 3 USA

Joining and Sealing Materials

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Thread Compounds
White Teflon 222 Pipe Thread Sealant >= 1/2" C. HOT TS
22202 >= 1/2" C. HOT TS
22203 >= 1/2" C. HOT TS
Heavy Blue Industrial Pipe Thread Sealant >= 1/2" C. HOT TS
88802 >= 1/2" C. HOT TS
88803 >= 1/2" C. HOT TS
Gold 555 Pipe Thread Sealant[1] >= 1/2" C. HOT TS
55502[1] >= 1/2" C. HOT TS
55503[1] >= 1/2" C. HOT TS

[1] Certified for the following colors: blue, gold, and white.



 
Lubricant Consult GmbH 
Gutenbergstrasse 13
D-63477 Maintal 
Germany 
49 6109 / 7650-0
Visit this company's website

Facility : Maintal, Germany

Joining and Sealing Materials

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Lubricants
Turmsilon GL 320-G >= 1/2" C. HOT LUB



 
LymTal International, Inc. 
60 Ocean Boulevard
Suite 5 
Atlantic Beach, FL 32233 
United States 
904-246-4507

Facility : # 1 USA

Joining and Sealing Materials

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Sealants
Iso-Flex 835 Polysulfide Sealant [1] CLD 23 PSU

[1] Certified for a maximum use of 1% of a 2,000,000 gallon tank or greater.



 
Lübke & Vogt GmbH & Co. KG 
Hüstener Strasse 43-45
59846 Sundern 
Germany 
49 2933 9747 0
Visit this company's website

Facility : Sundern, Germany

Joining and Sealing Materials

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Gasket/Sealing Materials
EPDM 0713.17/55[2] [1] C. HOT EPDM
EPDM 0713.17/60[2] [1] C. HOT EPDM
EPDM 0713.17/65[2] [1] C. HOT EPDM
EPDM 0713.17/70[2] [1] C. HOT EPDM

[1] Certified for a maximum surface area to volume ratio of 2.0 sq. in./L.
[2] This product has also been evaluated for use in Mechanical Plumbing Device applications
    with a maximum use restriction of 2.0 sq. in./L.

O-Rings
EPDM 0713.17/55[2] [1] C. HOT EPDM
EPDM 0713.17/60[2] [1] C. HOT EPDM
EPDM 0713.17/65[2] [1] C. HOT EPDM
EPDM 0713.17/70[2] [1] C. HOT EPDM

[1] Certified for a maximum surface area to volume ratio of 2.0 sq. in./L.
[2] This product has also been evaluated for use in Mechanical Plumbing Device applications
    with a maximum use restriction of 2.0 sq. in./L.



 
Manus Products, Inc. 
866 Industrial Boulevard W.
Waconia, MN 55387 
United States 
952-442-3323
Visit this company's website

Facility : Waconia, MN

Joining and Sealing Materials

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Sealants
Manus-Bond 75-AM Adhesive/Sealant Black[2] .036 sq. in./L[1] C. HOT MLTPL
Manus-Bond 75-AM Adhesive/Sealant Gray[2] .036 sq. in./L[1] C. HOT MLTPL
Manus-Bond 75-AM Adhesive/Sealant White[2] .036 sq. in./L[1] C. HOT MLTPL
Manus-Bond 75-AM Adhesive/Sealant Capital Tan[2] .036 sq. in./L[1] C. HOT MLTPL

[1] Size corresponds to requested usage of a minimum tank size of 100,000 gallons with a
    maximum surface area of sealant of 2.85%.
[2] Only products bearing the NSF Mark on the product, product packaging, and/or
    documentation shipped with the product are Certified.



 
Manuspec Co., Inc. 
23802 FM2978 - Building #C2
Tomball, TX 77375 
United States 
281-351-9889
Visit this company's website

Facility : Tomball, TX

Joining and Sealing Materials

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Lubricants
True Blue Pipe/Gasket Lubricant [1] CLD 23 LUB

[1] Certified for use with pipes 1/2" and greater.

Thread Compounds[2]
MS67 Multi-Seal Thread Sealant >= 1/2" C. HOT TS
MS92 Multi-Seal with Teflon Thread Sealant[3] >= 1/2" C. HOT TS

[2] Listed models have lot #503311 or greater.
[3] Certified for the following colors: blue, gold, and white.



 
Mar-Kell Seal / Mr Global Express, Inc. 
3506 West Lake Center Drive
Suite C 
Santa Ana, CA 92704 
United States 
714-546-0994

Facility : # 1 Taiwan

Joining and Sealing Materials

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Gasket/Sealing Materials
E360A [2] C. HOT EPDM
E370A [2] C. HOT EPDM
E380A [2] C. HOT EPDM
N660A[3] [1] C. HOT NBR

[1] Certified for a maximum surface area to volume ratio of 0.5 sq. in./L.
[2] Certified for a maximum surface area to volume ratio of 2.0 sq. in./L.
[3] This product has also been evaluated for use in Mechanical Plumbing Device applications
    with a maximum use restriction of 0.2 sq. in./L.



 
Max Seal SA de CV 
Calle Carlos Salinas de Gortari #1
Infonavit Presidentes 
Tijuana, BC 22215 
Mexico 
52 664 625 4885

Facility : Tijuana, BC, Mexico

Joining and Sealing Materials

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Gasket/Sealing Materials
C900 Rieber [1] CLD 23 SBR
C905 Rieber [1] CLD 23 SBR
IPS Rieber [1] CLD 23 SBR
Pressure Metric Rieber [1] CLD 23 SBR

[1] Certified for a maximum surface area to volume ratio of 0.2 sq. in./L.



 
Merrill Mfg. 
315 Flindt Drive
Storm Lake, IA 50588 
United States 
800-831-6962

Facility : # 1 USA

Joining and Sealing Materials

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Sealants[G]
Aqua Seal >= 1/2" C. HOT NA

[G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for
    “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state
    laws and the U.S. Safe Drinking Water Act.

    



 
Metall-Kunstoff-Technik GmbH & Co.KG 
Auf dem Immel 2
67685 Weilerbach 
Germany 
4963749116 301

Facility : # 2 Germany

Joining and Sealing Materials

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Adhesives
VME [1] D. HOT EPOXY
VMU plus [1] C. HOT VE

[1] Certified for use as an anchoring adhesive for installing thread rods (less than or
    equal to 1.3 inches in diameter) in concrete or masonry for water treatment applications.



 
MFC Sealing Technology Co., Ltd. / MFC Sealing Technology (Shenzhen) Co., Ltd. 
No. 41 Wu-Chuan-Wu Road
Wu-ku Industrial Zone, Taipei Hsien 248 
Taiwan 
86 755 2882 8056

Facility : Shen-Zhen City, China

Joining and Sealing Materials

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Gasket/Sealing Materials
E7014F [6] C. HOT EPDM
E7035PF[5] 1.0 sq. in./L C. HOT EPDM
E8004F[4] 2.0 sq. in./L C. HOT EPDM
N7012F[3] 2.0 sq. in./L C. HOT NBR
S7040F[1] 2.0 sq. in./L C. HOT SLC

[1] This product has also been evaluated for use in Mechanical Plumbing Device applications
    with a maximum use restriction of 2.0 sq. in./L.
[3] This product has also been evaluated for use in Mechanical Plumbing Device applications
    with a maximum use restriction of 0.2 sq. in./L.
[4] This product has also been evaluated for use in Mechanical Plumbing Device applications
    with a maximum use restriction of 0.4 sq. in./L.
[5] This product has also been evaluated for use in Mechanical Plumbing Device applications
    with a maximum use restriction of 0.1 sq. in./L.
[6] Certified for a maximum surface area to volume ratio of 2.0 sq. in./L.

O-Rings
E7014F [6] C. HOT EPDM
E7035PF[5] 1.0 sq. in./L C. HOT EPDM
E8004F[4] 2.0 sq. in./L C. HOT EPDM
N7012F[3] 2.0 sq. in./L C. HOT NBR
S7040F[1] 2.0 sq. in./L C. HOT SLC

[1] This product has also been evaluated for use in Mechanical Plumbing Device applications
    with a maximum use restriction of 2.0 sq. in./L.
[3] This product has also been evaluated for use in Mechanical Plumbing Device applications
    with a maximum use restriction of 0.2 sq. in./L.
[4] This product has also been evaluated for use in Mechanical Plumbing Device applications
    with a maximum use restriction of 0.4 sq. in./L.
[5] This product has also been evaluated for use in Mechanical Plumbing Device applications
    with a maximum use restriction of 0.1 sq. in./L.
[6] Certified for a maximum surface area to volume ratio of 2.0 sq. in./L.



 
Minnesota Rubber 
3630 Wooddale Avenue South
Minneapolis, MN 55416 
United States 
612-927-2248

Facility : # 1 Italy

Joining and Sealing Materials

    Water Water
    Contact Contact
Trade Designation Size Temp Material

O-Rings
212N [1] C. HOT EPDM
210N [1] CLD 23 NBR

[1] Certified for a maximum surface area to volume ratio of 2.0 sq. in./L.



 
Minnesota Rubber and Plastics 
1100 Xenium Lane North
Plymouth, MN 55441 
United States 
800-927-1422 
952-927-1400
Visit this company's website

Facility : Mason City, IA

Joining and Sealing Materials

    Water Water
    Contact Contact
Trade Designation Size Temp Material

O-Rings
210N [1] CLD 23 NBR
212N [1] C. HOT EPDM

[1] Certified for a maximum surface area to volume ratio of 2.0 sq. in./L.


Facility : Litchfield, MN

Joining and Sealing Materials

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Gasket/Sealing Materials
534DF [1] CLD 23 NBR
534HC[2] [1] CLD 23 NBR
559GT[2] [1] C. HOT EPDM
559N[3] [4] C. HOT EPDM
559PE[5] [6] C. HOT EPDM
559TM[7] [1] C. HOT EPDM
559YU[2] [1] C. HOT EPDM
560CF[2] [1] C. HOT EPDM
560RJ[8] [4] C. HOT EPDM
560YH [1] C. HOT EPDM
561NZ[2] [1] C. HOT EPDM
561TX[2] [1] C. HOT EPDM
565CZ [1] C. HOT EPDM
574J[2] [1] C. HOT HNBR
574TA[2] [1] C. HOT HNBR
76155 [1] C. HOT SLC
76156 [1] C. HOT SLC
76157 [1] C. HOT SLC
76187D [1] C. HOT SLC

[1] Certified for a maximum surface area to volume ratio of 2.0 sq. in./L.
[2] This product has also been evaluated for use in Mechanical Plumbing Device applications
    with a maximum surface area to volume ratio of 2.0 sq. in./L.
[3] This product has also been evaluated for use in Mechanical Plumbing Device applications
    with a maximum use restriction of 1.0 sq. in./L.
[4] Certified for a maximum surface area to volume ratio of 4.0 sq. in./L.
[5] This product has also been evaluated for use in Mechanical Plumbing Device applications
    with a maximum use restriction of 8.0 sq. in./L.
[6] Certified for a maximum surface area to volume ratio of 14.0 sq. in./L.
[7] This product has also been evaluated for use in Mechanical Plumbing Device applications
    with a maximum use restriction of 4.0 sq. in./L.
[8] This product has also been evaluated for use in Mechanical Plumbing Device applications
    with a maximum use restriction of 1.5 sq. in./L.

O-Rings
574J[2] [1] C. HOT HNBR
76187D [1] C. HOT SLC

[1] Certified for a maximum surface area to volume ratio of 2.0 sq. in./L.
[2] This product has also been evaluated for use in Mechanical Plumbing Device applications
    with a maximum surface area to volume ratio of 2.0 sq. in./L.

NOTE: Only products manufactured at an NSF authorized facility and bearing the NSF Mark are
      considered Certified.

Facility : Watertown, SD

Joining and Sealing Materials

    Water Water
    Contact Contact
Trade Designation Size Temp Material

O-Rings
210N [1] CLD 23 NBR
212N [1] CLD 23 EPDM

[1] Certified for a maximum surface area to volume ratio of 2.0 sq. in./L.

Gasket/Sealing Materials
366SM [1] C. HOT NBR
558BM[2] [3] CLD 23 EPDM
559GT[4] [1] C. HOT EPDM
559N[2] [3] C. HOT EPDM
559PE[5] [6] C. HOT EPDM
559TM[7] [1] C. HOT EPDM
559YU[4] [1] C. HOT EPDM
560CF[4] [1] C. HOT EPDM
560RJ[8] [3] C. HOT EPDM
560YH [1] C. HOT EPDM
561NZ[4] [1] C. HOT EPDM
561TX[4] [1] C. HOT EPDM
565CZ [1] C. HOT EPDM

[1] Certified for a maximum surface area to volume ratio of 2.0 sq. in./L.
[2] This product has also been evaluated for use in Mechanical Plumbing Device applications
    with a maximum use restriction of 1.0 sq. in./L.
[3] Certified for a maximum surface area to volume ratio of 4.0 sq. in./L.
[4] This product has also been evaluated for use in Mechanical Plumbing Device applications
    with a maximum use restriction of 0.2 sq. in./L.
[5] This product has also been evaluated for use in Mechanical Plumbing Device applications
    with a maximum use restriction of 8.0 sq. in./L.
[6] Certified for a maximum surface area to volume ratio of 14.0 sq. in./L.
[7] This product has also been evaluated for use in Mechanical Plumbing Device applications
    with a maximum use restriction of 4.0 sq. in./L.
[8] This product has also been evaluated for use in Mechanical Plumbing Device applications
    with a maximum use restriction of 1.5 sq. in./L.

NOTE: Only products manufactured at an NSF authorized facility and bearing the NSF Mark are
      considered Certified.

Facility : Guangdong, China

Joining and Sealing Materials

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Gasket/Sealing Materials
217AB[2] [1] C. HOT SLC

[1] Certified for a maximum surface area to volume ratio of 4.0 sq. in./L.
[2] This product has been evaluated for use in Mechanical Plumbing Device applications with
    a maximum use restriction of 4.0 sq. in./L.


Facility : Jiangsu, China

Joining and Sealing Materials

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Gasket/Sealing Materials
534HC[2] [1] CLD 23 NBR
559GT[2] [1] C. HOT EPDM
559N[3] [4] C. HOT EPDM
559PE[5] [6] C. HOT EPDM
559TM[7] [1] C. HOT EPDM
559YU[2] [1] C. HOT EPDM
560CF[2] [1] C. HOT EPDM
560RJ[8] [4] C. HOT EPDM
561TX[2] [1] C. HOT EPDM
565CZ [1] C. HOT EPDM
76155 [1] C. HOT SLC
76156 [1] C. HOT SLC
76157 [1] C. HOT SLC

[1] Certified for a maximum surface area to volume ratio of 2.0 sq. in./L.
[2] This product has also been evaluated for use in Mechanical Plumbing Device applications
    with a maximum use restriction of 2.0 sq. in./L.
[3] This product has also been evaluated for use in Mechanical Plumbing Device applications
    with a maximum use restriction of 1.0 sq. in./L.
[4] Certified for a maximum surface area to volume ratio of 4.0 sq. in./L.
[5] This product has also been evaluated for use in Mechanical Plumbing Device applications
    with a maximum use restriction of 8.0 sq. in./L.
[6] Certified for a maximum surface area to volume ratio of 14.0 sq. in./L.
[7] This product has also been evaluated for use in Mechanical Plumbing Device applications
    with a maximum use restriction of 4.0 sq. in./L.
[8] This product has also been evaluated for use in Mechanical Plumbing Device applications
    with a maximum use restriction of 1.5 sq. in./L.


Facility : Reynosa, Tamaulipas, Mexico

Joining and Sealing Materials

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Gasket/Sealing Materials
366SM [1] C. HOT NBR
534DF [1] CLD 23 NBR
534HC[2] [1] CLD 23 NBR
558BM [1] CLD 23 EPDM
559GT[2] [1] C. HOT EPDM
559N[3] [4] C. HOT EPDM
559PE[5] [6] C. HOT EPDM
559TM[7] [1] C. HOT EPDM
559YU[2] [1] C. HOT EPDM
560CF[2] [1] C. HOT EPDM
560RJ[8] [4] C. HOT EPDM
560YH [1] C. HOT EPDM
561NZ[2] [1] C. HOT EPDM
561TX[2] [1] C. HOT EPDM
565CZ C. HOT EPDM
71105B[2] [1] CLD 23 SLC

[1] Certified for a maximum surface area to volume ratio of 2.0 sq. in./L.
[2] This product has also been evaluated for use in Mechanical Plumbing Device applications
    with a maximum use restriction of 2.0 sq. in./L.
[3] This product has also been evaluated for use in Mechanical Plumbing Device applications
    with a maximum use restriction of 1.0 sq. in./L.
[4] Certified for a maximum surface area to volume ratio of 4.0 sq. in./L.
[5] This product has also been evaluated for use in Mechanical Plumbing Device applications
    with a maximum use restriction of 2.5 sq. in./L.
[6] Certified for a maximum surface area to volume ratio of 14.0 sq. in./L.
[7] This product has also been evaluated for use in Mechanical Plumbing Device applications
    with a maximum use restriction of 2.5 sq. in./L.
[8] This product has also been evaluated for use in Mechanical Plumbing Device applications
    with a maximum use restriction of 1.5 sq. in./L.

NOTE: NSF has not conducted production control audits at this facility. Product Listing is
      based on type testing [ISO/IEC Guide 2: 1996(E/F/R) 14.5].
NOTE: Only products manufactured at an NSF authorized facility and bearing the NSF Mark are
      considered Certified.


 
Mungo Befestigungstechnik AG 
Bornfeldstrasse 2
Olten 4603 
Switzerland 
41 62 206 7575

Facility : # 2 Germany

Joining and Sealing Materials

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Adhesives
MIT 600 RE [1] D. HOT EPOXY
MIT-SE Plus [1] D. HOT VE

[1] Certified for use as an anchoring adhesive for installing thread rods (less than or
    equal to 1.3 inches in diameter) in concrete or masonry for water treatment applications.



 
NCH Corporation 
2727 Chemsearch Boulevard
Irving, TX 75062 
United States 
972-438-0211

Facility : # 1 USA

Joining and Sealing Materials

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Patching Materials
Mega Stick [1] C. HOT EPOXY
Quick Cure [1] C. HOT EPOXY
Quick Steel [1] C. HOT EPOXY

[1] The exposed surface area of each sealant in a household distribution system
    should not exceed 1.3 sq. cm/L or .2 sq. in/L.



 
Neptune Research, Inc. 
3875 Fiscal Court #100
Riviera Beach, FL 33404 
United States 
561-683-6992

Facility : # 1 USA

Joining and Sealing Materials

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Patching Materials
Syntho-Steel [1] C. HOT EPOXY

[1] The exposed surface area of each sealant in a household distribution system should not
    exceed 1.3 sq. cm/L or .2 sq. in./L



 
New Pig Corporation 
One Pork Avenue
Tipton, PA 16684 
United States 
215-935-1170

Facility : # 1 USA

Joining and Sealing Materials

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Patching Materials
PIG® Repair Putty [1] C. HOT EPOXY

[1] The exposed surface area of each sealant in a household distribution system should not
    exceed 1.3 sq. cm/L or .2 sq. in/L.



 
Nok Klüber Co., Ltd. 
1-12-15 Shiba Daimon
Minato-ku, Tokyo 105-0012 
Japan 
81 3 3434 1734
Visit this company's website

Facility : Ibaraki-ken, Japan

Joining and Sealing Materials

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Lubricants
Klübersynth UH1 64-2403 >= 1/2" C. HOT LUB
PARALIQ GTE 703 >= 1/2" C. HOT LUB
UNISILKON L 250 L >= 1/2" C. HOT LUB
UNISILKON L 641 >= 1/2" C. HOT LUB



 
Novagard Solutions™, Inc. 
5109 Hamilton Avenue
Cleveland, OH 44114 
United States 
800-380-0138 
216-881-8111

Facility : Cleveland, OH

Joining and Sealing Materials

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Lubricants
G-662 Silicone Compound >= 1/2" C. HOT SLC



 
Oatey Company 
4700 West 160th Street
Cleveland, OH 44135 
United States 
800-203-1155 
216-267-7100
Visit this company's website

Facility : Omaha, NE

Joining and Sealing Materials

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Thread Compunds
Megaloc >= 1/2" C. HOT TC
Oatey Great Blue Pipe Joint Compound >= 1/2" C. HOT TC
Oatey Great White Pipe Joint Compound with PTFE >= 1/2" C. HOT TC
Oatey Pipe Joint Compound >= 1/2" C. HOT TC
Real Tuff Thread Sealant >= 1/2" C. HOT SLT


Facility : Cleveland, OH

Joining and Sealing Materials

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Brazing/Solders/Fluxes[1]
Oatey #11 Liquid Soldering Flux >= 1/2" C. HOT FLX
Oatey All-Purpose Liquid Soldering Flux >= 1/2" C. HOT FLX
Oatey Liquid Soldering Flux >= 1/2" C. HOT FLX

[1] Only products bearing the NSF Mark on the product, product packaging, and/or
    documentation shipped with the product are Certified.

Thread Compounds[1]
Oatey Great Blue Pipe Joint Compound >= 1/2" C. HOT TC
Oatey Great White Pipe Joint Compound >= 1/2" C. HOT TC
Oatey Great White Pipe Joint Compound with PTFE >= 1/2" C. HOT TC
Oatey Pipe Joint Compound >= 1/2" C. HOT TC

[1] Only products bearing the NSF Mark on the product, product packaging, and/or
    documentation shipped with the product are Certified.


Facility : Medina, OH

Joining and Sealing Materials

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Brazing/Solders/Fluxes
Oatey #11 Liquid Soldering Flux >= 1/2" C. HOT FLX
Oatey Liquid Soldering Flux >= 1/2" C. HOT FLX
Oatey All-Purpose Liquid Soldering Flux >= 1/2" C. HOT FLX


Facility : Sonora, Mexico

Joining and Sealing Materials

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Brazing/Solders/Fluxes
Eluma Especifica Para Soldagem De Tubos De Cobre E Conexoes De Cobre e Bronze >= 1/2" C. HOT FLX
Oatey H-20®5 Water Soluble Paste Flux >= 1/2" C. HOT FLX
Oatey H-20®95 Water Soluble Tinning Flux >= 1/2" C. HOT FLX
Oatey No. 5 Hot Weather Paste Flux >= 1/2" C. HOT FLX
Oatey No. 5 Lead Free Solder Paste >= 1/2" C. HOT FLX
Oatey No. 95 Lead Free Tinning Flux >= 1/2" C. HOT FLX



 
Oatey Company 
4700 West 160th Street
P.O. Box 35906 
Cleveland, OH 44135 
United States 
216-267-7100
Visit this company's website

Facility : Solon, OH

Joining and Sealing Materials

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Lubricants[G]
Oatey All Purpose Pipe Lubricant >= 1/2" CLD 23 LUB

[G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for
    “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state
    laws and the U.S. Safe Drinking Water Act.

    



 
Oatey Company 
4700 West 160th Street
Cleveland, OH 44135 
United States 
216-898-3443

Facility : # 1 USA

Joining and Sealing Materials

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Patching Materials
Fix It Stick[G] [1] C. HOT EPOXY

[1] The exposed surface area of each sealant in a household distribution system shall not
    exceed 1.3 sq. cm/L or .2 sq. in./L.
[G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for
    “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state
    laws and the U.S. Safe Drinking Water Act.

    



 
Origom Spa 
Via Castello 14 A
24060 Viadanica (BG) 
Italy 
39 03 593 9911

Facility : Viadanica (BG), Italy

Joining and Sealing Materials

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Gasket/Sealing Materials
E50N00G [1] CLD 23 EPDM

[1] Certified for a maximum surface area to volume ratio of 2.0 sq. in./L
[2] Certified for a maximum suface area to volume ratio of 20 sq. in./L.
[3] This product has also been evaluated for use in Mechanical Plumbing Device applications
    with a maximum use restriction of 2.0 sq. in./L.
[G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for
    “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state
    laws and the U.S. Safe Drinking Water Act.

    

O-Rings
N85N00G[G] [2] [3] D. HOT NBR
N70N06G[G] [2] [3] D. HOT NBR
E70N01C[G] [1] [3] C. HOT EPDM
E50N00G [1] CLD 23 EPDM

[1] Certified for a maximum surface area to volume ratio of 2.0 sq. in./L
[2] Certified for a maximum suface area to volume ratio of 20 sq. in./L.
[3] This product has also been evaluated for use in Mechanical Plumbing Device applications
    with a maximum use restriction of 2.0 sq. in./L.
[G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for
    “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state
    laws and the U.S. Safe Drinking Water Act.

    

Gasket/Sealing Materials
N85N00G[G] [2] [3] D. HOT NBR
N70N06G[G] [2] [3] D. HOT NBR
E70N01C[G] [1] [3] C. HOT EPDM

[1] Certified for a maximum surface area to volume ratio of 2.0 sq. in./L
[2] Certified for a maximum suface area to volume ratio of 20 sq. in./L.
[3] This product has also been evaluated for use in Mechanical Plumbing Device applications
    with a maximum use restriction of 2.0 sq. in./L.
[G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for
    “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state
    laws and the U.S. Safe Drinking Water Act.

    



 
Orox Specialty Chemicals, Inc. 
416 Westfield Avenue
Westfield, NJ 07090-2126 
United States 
908-233-8060

Facility : # 1 USA

Joining and Sealing Materials

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Lubricants
OSC222 Silicone Grease >= 1/2" pipe C. HOT SLC
OSC222H Silicone Grease >= 1/2" pipe C. HOT SLC



 
Pacer Technology / Super Glue Corporation 
9420 Santa Anita Avenue
Rancho Cucamonga, CA 91730 
United States 
800-538-3091 
909-987-0550
Visit this company's website

Facility : Rancho Cucamonga, CA

Joining and Sealing Materials

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Adhesives[1]
Copper-Bond Kit NA C. HOT ADH

[1] Certified for use with pipes 3/4 inch in diameter or greater.



 
Parabond Pipe Cement Company, Inc. 
190 East Washington Street
Chagrin Falls, OH 44022 
United States 
877-803-3274 
407-240-4154

Facility : # 1 USA

Joining and Sealing Materials

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Solvent Cements
PARABOND P-600 Clear PVC[G] >= 1/2" CLD 23 NA
PARABOND P10 PVC Cement Clear[G] >= 1/2" CLD 23 NA
PARABOND P8 PVC Cement Clear[G] >= 1/2" CLD 23 NA

[G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for
    “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state
    laws and the U.S. Safe Drinking Water Act.

    



 
Parco, Inc. 
1801 South Archibald Avenue
Ontario, CA 91761 
United States 
909-947-2200

Facility : Ontario, CA

Joining and Sealing Materials

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Gasket/Sealing Materials[1]
5300-70[3] [2] C. HOT EPDM
5778-70-71[3] [2] C. HOT EPDM
EPDM Compound 5763-70 [2] CLD 23 EPDM
EPDM Compound 5778-50 [2] C. HOT EPDM
EPDM Compound 5778-70 [2] C. HOT EPDM
EPDM Compound 5778-80[3] [2] C. HOT EPDM
EPDM Compound 5778-90[3] [2] C. HOT EPDM

[1] Only products bearing the NSF Mark on the product, product packaging, and/or
    documentation shipped with the product are Certified.
[2] Certified for a maximum surface area to volume ratio of 2.0 sq. in./L.
[3] This product has also been evaluated for use in Mechanical Plumbing Device applications
    with a maximum use restriction of 0.2 sq. in./L.

O-Rings[1]
5300-70[3] [2] C. HOT EPDM
5778-70-71[3] [2] C. HOT EPDM
EPDM Compound 5763-70 [2] CLD 23 EPDM
EPDM Compound 5778-50 [2] C. HOT EPDM
EPDM Compound 5778-70 [2] C. HOT EPDM
EPDM Compound 5778-80[3] [2] C. HOT EPDM
EPDM Compound 5778-90[3] [2] C. HOT EPDM

[1] Only products bearing the NSF Mark on the product, product packaging, and/or
    documentation shipped with the product are Certified.
[2] Certified for a maximum surface area to volume ratio of 2.0 sq. in./L.
[3] This product has also been evaluated for use in Mechanical Plumbing Device applications
    with a maximum use restriction of 0.2 sq. in./L.



 
Parco, Inc. 
1801 South Archibald Avenue
Ontario, CA 91761 
United States 
909-947-2200

Facility : # 2 China

Joining and Sealing Materials

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Gasket/Sealing Materials
1225-40[2] [1] C. HOT SLC
1225-70[2] [1] C. HOT SLC
1229-60[2] [1] C. HOT SLC
4926-70 [4] C. HOT NBR
4926-75 [4] C. HOT NBR
4926-80[3] [4] C. HOT NBR
5315-60[3] [1] C. HOT EPDM
5315-70 [1] C. HOT EPDM
5315-80[3] [1] C. HOT EPDM
5323-70[5] [1] C. HOT EPDM
5323-80[2] [1] C. HOT EPDM
5325-70[6] [7] C. HOT EPDM

[1] Certified for a maximum surface area to volume ratio of 2.0 sq. in./L.
[2] This product has also been evaluated for use in Mechanical Plumbing Device applications
    with a maximum surface area to volume ratio of 2.0 sq. in./L.
[3] This product has also been evaluated for use in Mechanical Plumbing Device applications
    with a maximum use restriction of 0.2 sq. in./L.
[4] Certified for a maximum surface area to volume ratio of 1.6 sq. in./L.
[5] This product has also been evaluated for use in Mechanical Plumbing Device applications
    with a maximum use restriction of 1.1 sq. in./L.
[6] This product has also been evaluated for use in Mechanical Plumbing Device applications
    with a maximum use restriction of 0.1 sq. in./L.
[7] Certified for a maximum surface area to volume ratio of 1.3 sq. in./L.



 
Parker Seal - Techseal Division 
3025 West Croft Circle Drive
Spartanburg, SC 29302 
United States 
864-515-6028

Facility : Spartanburg, SC

Joining and Sealing Materials

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Gasket/Sealing Materials
E-7871-75 [1] C. HOT EPDM
E7126-80 [2] D. HOT EPDM

[1] Certified for a maximum surface area to volume ratio of 0.6 sq. in./L.
[2] Certified for a maximum surface area to volume ratio of 2.0 sq. in./L.

O-Rings
EJ583-70[3] [2] CLD 23 EPDM

[2] Certified for a maximum surface area to volume ratio of 2.0 sq. in./L.
[3] This product has also been evaluated for use in Mechanical Plumbing Device applications
    with a maximum use restriction of 2.0 square in./L.



 
Parker Seal O-Ring Division 
Parker Hannifin Corporation
2360 Palumbo Drive 
Lexington, KY 40509 
United States 
859-335-5154

Facility : # 2 H. Matamoros, Mexico

Joining and Sealing Materials

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Gasket/Sealing Materials
Compound E1242 [1] C. HOT EPDM
Compound E1244 [1] C. HOT EPDM
Compound E3609 [1] C. HOT EPDM
Compound EA140-70 [2] C. HOT EPDM
Compound EJ151-80 [3] C. HOT EPDM

[1] Certified for a maximum surface area to volume ratio of 2.0 sq. in./L.
[2] Certified for a maximum surface area to volume ratio of 0.65 sq. in./L.
[3] Certified for a maximum surface area to volume ratio of 0.3 sq. in./L.

O-Rings
Compound EA140-70 [2] C. HOT EPDM
Compound EJ151-80 [3] C. HOT EPDM
E1244-70 [1] C. HOT EPDM
E1257-70 [1] C. HOT EPDM
EJ274-70[4] [1] C. HOT EPDM

[1] Certified for a maximum surface area to volume ratio of 2.0 sq. in./L.
[2] Certified for a maximum surface area to volume ratio of 0.65 sq. in./L.
[3] Certified for a maximum surface area to volume ratio of 0.3 sq. in./L.
[4] Certified for use in Mechanical Plumbing Device applications with a maximum surface area
    to volume ratio of 0.8 sq. in./L.

NOTE: NSF has not conducted production control audits at this facility. Product Listing is
      based on type testing [ISO/IEC Guide 2: 1996(E/F/R) 14.5].

Facility : Changhua Hsien, Taiwan

Joining and Sealing Materials

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Gasket/Sealing Materials
Compound E1570 [1] C. HOT EPDM
Compound E1571 [1] C. HOT EPDM
Compound N1517 [1] C. HOT NBR

[1] Certified for a maximum surface area to volume ratio of 2.0 sq. in./L.



 
Parker-Asun Sealing Company (PASC) 
No. 26, Tian Bao Ind. Zone
Dongguan City, Guan Dong Province 
China 
86 769 226 8836

Facility : Dongguan City, China

Joining and Sealing Materials

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Gasket/Sealing Materials
67997 [1] C. HOT NBR
E1512-70 [2] C. HOT EPDM
E1549-70 [2] C. HOT EPDM
E1561-60 [2] C. HOT EPDM
E1583-70 [2] C. HOT EPDM
EPDM Compound 63017 [2] C. HOT EPDM
EPDM Compound 63446 [2] C. HOT EPDM
EPDM Compound 63447 [2] C. HOT EPDM
N1510-70 [1] C. HOT NBR

[1] Certified for a maximum surface area to volume ratio of 0.5 sq. in./L.
[2] Certified for a maximum surface area to volume ratio of 2.0 sq. in./L.

O-Rings
E1512-70 [2] C. HOT EPDM

[2] Certified for a maximum surface area to volume ratio of 2.0 sq. in./L.



 
Pecora Corporation 
165 Wambold Road
Harleysville, PA 19438 
United States 
215-723-6051

Facility : # 1 USA

Joining and Sealing Materials

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Sealants
GC-2+ [1] CLD 30 PSU

[1] Certified for a maximum use of 1% of a 250,000 gallon tank or greater, or 2%
    of a 2,000,000 gallon tank or greater.



 
Permabond LLC 
223 Churchill Avenue
Somerset, NJ 08873 
United States 
800-640-7599 
732-868-0164
Visit this company's website

Facility : Cesano Maderno, Italy

Joining and Sealing Materials

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Thread Compounds
Permabond HH040 Pure™ >= 1/2" C. HOT TC
Permabond LH050 Pure™[1] >= 1/2" C. HOT TC
Permabond LH051 Pure™[1] >= 1/2" C. HOT TC
Permabond MM115 Pure™[2] >= 1/2" C. HOT TC

[1] Certified for a maximum of 1 joint per liter or (10) 1/2" joints per residence.
[2] Certified for a maximum of 1.5 joints per liter or (16) 1/2" joints per residence.



 
PL Sourcing, Inc. 
P.O. Box 2778
Newport News, VA 23609 
United States 
757-874-7795

Facility : # 1 USA

Joining and Sealing Materials

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Lubricants[G]
PROSELECT Water Soluble Pipe Joint Lubricant >= 1/2" CLD 23 LUB

[G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for
    “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state
    laws and the U.S. Safe Drinking Water Act.

    



 
Polymeric Systems, Inc. 
47 Park Avenue
Box 522 
Elverson, PA 19520 
United States 
610-286-2500

Facility : Elverson, PA

Joining and Sealing Materials

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Patching Materials
AQUAMEND® White [1] C. HOT EPOXY
E20M12 [1] C. HOT EPOXY
Faststeel® [1] C. HOT EPOXY
IF RepairitQuik [1] C. HOT EPOXY
PSI Poxy [1] C. HOT EPOXY
Quikcopper® [1] C. HOT EPOXY
Quikplastik® [1] C. HOT EPOXY
Repairitquik®[G] [1] C. HOT EPOXY

[1] The exposed surface area of each sealant in a household distribution system shall not
    exceed 1.3 sq. cm/L or .2 sq. in./L
[G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for
    “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state
    laws and the U.S. Safe Drinking Water Act.

    



 
Polysi Technologies, Inc. 
5108 Rex McLeod Drive
Sanford, NC 27330 
United States 
919-775-4989
Visit this company's website

Facility : Sanford, NC

Joining and Sealing Materials

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Lubricants
PST-599 >= 1/2" C. HOT SLC



 
Polytech Industries LLC 
Rakia Industrial Zone, Wiz-04
WH 25-28, Al Jazira Al Hamra 
Ras Al Khaimah 35892 
United Arab Emirates 
971 7 243 4951
Visit this company's website

Facility : Ras Al Khaimah, United Arab Emirates

Joining and Sealing Materials

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Gasket/Sealing Materials
EPDM Rubber Gasket for Pipe Sealing [1] D. HOT EPDM
PIL/FS [1] D. HOT EPDM
PIL/Sealing Gasket [1] D. HOT EPDM

[1] Certified for a maximum surface area to volume ratio of 2 sq. in./L.

NOTE: Only products bearing the NSF Mark on the product, product packaging, and/or
      documentation shipped with the product are Certified.


 
Powers Fasteners, Inc. 
2 Powers Lane
Brewster, NY 10509 
United States 
914-235-6300

Facility : # 1 Germany

Joining and Sealing Materials

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Adhesives
AC100+ Gold [1] D. HOT VE
AC100-PRO [1] D. HOT VE
PE 1000+ [1] D. HOT EPOXY
PF PRO [1] D. HOT EPOXY
PURE150-PRO [1] D. HOT EPOXY
V12 [1] D. HOT VE

[1] Certified or use as an anchoring adhesive for installing thread rods (less than or equal
    to 1.3 inches in diameter) in concrete or masonry for water treatment applications.



 
Prabhat Elastomers Pvt. Ltd. 
'Prabhat Bhavan', 96, LBS MARG
Vikhroli (W), Mumbai 400 083 
India 
877-503-8965 
91 22 32946102
Visit this company's website

Facility : Gujarat, India

Joining and Sealing Materials

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Gasket/Sealing Materials
AED 50 T5 >= 4" CLD 23 EPDM
AED 67 T5 >= 4" CLD 23 EPDM
AED 85 T5 >= 4" CLD 23 EPDM
B 304 >= 2" CLD 23 SBR
BC 309 T 15 >= 2" CLD 23 SBR
BC 310 >= 2" CLD 23 SBR
BW 5910 >= 4" CLD 23 EPDM
CS3 >= 1 1/2" CLD 23 SBR
CS4 >= 2" CLD 23 SBR
D 555 >= 2" CLD 23 EPDM
D-719 >= 1" C. HOT EPDM
IEH 78 >= 4" CLD 23 EPDM
KH 1 >= 2" CLD 23 SBR
KH 2 >= 2" CLD 23 SBR
KH 4 >= 2" CLD 23 SBR
KH06 >= 2" CLD 23 SBR
KS1 >= 2" CLD 23 SBR
KS2 >= 2" CLD 23 SBR
S4 >= 1 1/2" CLD 23 SBR
S5 >= 1 1/2" CLD 23 SBR
S6 >= 1 1/2" CLD 23 SBR
UB 70E >= 1" CLD 23 EPDM
UB 75 E >= 2" C. HOT EPDM
ULE 5 >= 4" CLD 23 EPDM



 
Precision Associates Inc. 
3800 Washington Avenue North
Minneapolis, MN 55412 
United States 
612-333-7464
Visit this company's website

Facility : Minneapolis, MN

Joining and Sealing Materials

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Gasket/Sealing Materials
23761[1] [2] C. HOT EPDM

[1] This product has also been evaluated for use in Mechanical Plumbing Device applications
    with a maximum use restriction of 0.4 sq. in./L.
[2] Certified for a maximum surface area to volume ratio of 2.0 sq. in./L.

O-Rings
23761[1] [2] C. HOT EPDM

[1] This product has also been evaluated for use in Mechanical Plumbing Device applications
    with a maximum use restriction of 0.4 sq. in./L.
[2] Certified for a maximum surface area to volume ratio of 2.0 sq. in./L.



 
Precix Inc. 
744 Belleville Avenue
New Bedford, MA 02745 
United States 
508-998-4142

Facility : New Bedford, MA

Joining and Sealing Materials

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Gasket/Sealing Materials
E-17331 [1] C. HOT EPDM
E61 [1] C. HOT EPDM

[1] Certified for a maximum surface area to volume ratio of 2.0 sq. in./L.



 
Premier Repak, Inc. 
8351 185th Street
Tinley Park, IL 60487 
United States 
855-737-2500 
708-444-2688

Facility : # 1 USA

Joining and Sealing Materials

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Lubricants
PR5501 >= 1/2" C. HOT LUB

Thread Compounds
PR5501 >= 1/2" C. HOT LUB



PremierRepak, lnc. 
8351 185th Street
Tinley Park, IL 60487 
United States 
855-737-2500 

Facility : # 1 USA

Joining and Sealing Materials

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Lubricants
PR 5501 - High Consistency Silicone Valve and Oring Lubricant >= 1/2" C. HOT SLC



 
Premium Spray Products 
1255 Kennestone Circle
Suite 200 
Marietta, GA 30066 
United States 
770-528-9556
Visit this company's website

Facility : Marietta, GA

Joining and Sealing Materials

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Grouts
URETEK [1] CLD 23 PUR
URETEK Geopolymer[2] [1] CLD 23 PUR

[1] Certified for a maximum surface area to volume ratio of 0.1 sq. in./L.
[2] Certified for product with the following densities and reaction speeds:
    2 pounds per cubic foot (regular speed)
    2 pounds per cubic foot (fast speed)
    3 pounds per cubic foot (regular speed)
    3 pounds per cubic foot (fast speed)
    4 pounds per cubic foot (regular speed)
    4 pounds per cubic foot (fast speed)
    5 pounds per cubic foot (regular speed)
    5 pounds per cubic foot (fast speed)
    8 pounds per cubic foot (regular speed)
    8 pounds per cubic foot (fast speed)
    
    Mix ratio is 1:1 (A:B) by volume or 8.1:6.9 (A:B) by weight.
    Minimum cure time is 60 minutes at ambient temperatures.



 
Press-Seal Gasket Corporation 
2424 W. State Boulevard
Fort Wayne, IN 46808 
United States 
800-348-7325 
260-436-0521
Visit this company's website

Facility : Fort Wayne, IN

Joining and Sealing Materials

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Gasket/Sealing Materials
PS 55 IR/SBR-MB [1] CLD 23 MLTPL

[1] Certified for use in pipes 6" and greater.  Certification is for gasket only.

O-Rings
PS 55 IR/SBR-MB [1] CLD 23 MLTPL

[1] Certified for use in pipes 6" and greater.  Certification is for gasket only.



 
Protective Coating Co. 
221 South 3rd Street
Allentown, PA 18102-4922 
United States 
610-432-3543

Facility : # 1 USA

Joining and Sealing Materials

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Patching Materials
PC-Plumbing Epoxy Putty [1] C. HOT EPOXY
PC-Metal [1] C. HOT EPOXY

[1] The exposed surface area of each sealant in a household distribution system should not
    exceed 1.3 sq. cm/L or .2 sq. in/L



 
Pure Asphalt Company 
3455 West 31st Place
Chicago, IL 60623 
United States 
773-247-7030
Visit this company's website

Facility : Chicago, IL

Joining and Sealing Materials

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Lubricants
Pure Lube 400 >= 1/2" CLD 23 LUB
Pure Lube 500 >= 1/2" CLD 23 LUB



 
R.L. Hudson & Company 
2000 W. Tacoma
Broken Arrow, OK 74012 
United States 
918-663-1130

Facility : # 1 China

Joining and Sealing Materials

    Water Water
    Contact Contact
Trade Designation Size Temp Material

O-Rings
E3030-70[2] [1] C. HOT EPDM
N1030-70[3] [1] D. HOT NBR

[1] Certified for a maximum surface area to volume ratio of 2.0 sq. in./L.
[2] This product has also been evaluated for use in Mechanical Plumbing Device applications
    with a maximum surface area to volume ratio of 0.2 sq. in./L.
[3] This product has also been evaluated for use in Mechanical Plumbing Device applications
    with a maximum surface area to volume ratio of 0.2 sq. in./L.



 
R.L. Hudson & Company 
2000 West Tacoma
Broken Arrow, OK 74012 
United States 
918-259-6600

Facility : # 1 Taiwan

Joining and Sealing Materials

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Gasket/Sealing Materials
RL-N67015-A[2] [1] C. HOT NBR

[1] Certified for a maximum surface area to volume ratio of 0.5 sq. in./L.
[2] This product has also been evaluated for use in Mechanical Plumbing Device applications
    with a maximum surface area to volume ratio of 0.2 sq. in./L.

O-Rings
RL-N67015-A[2] [1] C. HOT NBR

[1] Certified for a maximum surface area to volume ratio of 0.5 sq. in./L.
[2] This product has also been evaluated for use in Mechanical Plumbing Device applications
    with a maximum surface area to volume ratio of 0.2 sq. in./L.



 
Railton Resources, Inc. 
3245-H East Patrick Lane
Las Vegas, NV 89120 
United States 
702-818-5589

Facility : # 1 Vietnam

Joining and Sealing Materials

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Gasket/Sealing Materials[1]
RR809 EPDM [2] D. HOT EPDM

[1] This product has also been evaluated for use in Mechanical Plumbing Device applications
    with a maximum use restriction of 2.0 sq. in./L.
[2] Certified for a maximum surface area to volume ratio of 2.0 sq. in./L.

O-Rings[1]
RR809 EPDM [2] D. HOT EPDM

[1] This product has also been evaluated for use in Mechanical Plumbing Device applications
    with a maximum use restriction of 2.0 sq. in./L.
[2] Certified for a maximum surface area to volume ratio of 2.0 sq. in./L.



 
RectorSeal 
2601 Spenwick Drive
Houston, TX 77055 
United States 
713-263-8001
Visit this company's website

Facility : # 1 USA

Joining and Sealing Materials

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Fluxes
NOKORODE® 95/5 Pre-Tinning Paste Flux[G] >= 1/2" C. HOT FLX
NOKORODE® Aqua-Flux™[G] >= 1/2" C. HOT FLX
NOKORODE® Regular Paste Flux[G] >= 1/2" C. HOT FLX

[G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for
    “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state
    laws and the U.S. Safe Drinking Water Act.

    

Solvent Cements
Sam™ CL-3[2] [G] >= 1/2" C. HOT CLE
Sam™ CL-3L - Low VOC[2] [G] >= 1/2" C. HOT CLE

[2] This product is a cleaner that is intended to be used directly before application of a
    solvent cement.  An additional primer is not required.
[G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for
    “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state
    laws and the U.S. Safe Drinking Water Act.

    

Thread Compounds
Blue+™[G] >= 1/2" C. HOT TC
No. 100 Virgin™[1] [G] >= 1/2" C. HOT TC
Pure White Teflon Pipe Compound[1] [3] [G] >= 1/2" C. HOT TC
RectorSeal® No. 5®[1] [G] >= 1/2" CLD 23 TC
RectorSeal® T Plus 2®[1] [G] >= 1/2" C. HOT TC
Tru-Blu™[1] [G] >= 1/2" CLD 23 TC

[1] Products were prepared for evaluation according to manufacturer's instructions.
[3] DuPont Registered Trademark.
[G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for
    “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state
    laws and the U.S. Safe Drinking Water Act.

    


Facility : # 3 USA

Joining and Sealing Materials

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Lubricants[G]
RectorSeal® Pipe Lube >= 1/2" CLD 23 LUB

[G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for
    “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state
    laws and the U.S. Safe Drinking Water Act.

    



 
Rectorseal Corporation 
2601 Spenwick Drive
Houston, TX 77055 
United States 
713-263-8001

Facility : # 2 USA

Joining and Sealing Materials

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Patching Materials [G]
RectorSeal EP200 Epoxy Putty [1] [2] C. HOT EPOXY
RectorSeal EP400 Epoxy Putty [1] [2] C. HOT EPOXY

[1] Certified for a maximum surface area to volume ratio of 0.3 sq. in./L in pipe or 1% of a
    20,000 gallon tank.
[2] To obtain the proper mix, use at least a 3/4" length, but no more than 1/3 of a full
    stick, of product which has been cut with a knife. Product must be mixed for 60-90
    seconds.
[G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for
    “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state
    laws and the U.S. Safe Drinking Water Act.

    



Ridge Tool Company 
400 Clark Street
Elyria, OH 44035-6001 
United States 
888-743-4333 

Facility : # 1 USA

Joining and Sealing Materials

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Thread Compounds
Ridgid Thread Sealant >= 1/2" C. HOT TC
Ridgid Thread Sealant with PTFE >= 1/2" C. HOT TC



 
Romac Industries, Inc. 
21919 20th Avenue S.E.
Suite 100 
Bothell, WA 98021-4404 
United States 
425-951-6273
Visit this company's website

Facility : Bothell, WA

Joining and Sealing Materials

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Gasket/Sealing Materials
9RST-N1[G] >= 4" CLD 23 NBR
9RST-N2-2[G] [1] CLD 23 NBR
9RST-N3-3[G] [1] CLD 23 NBR
9RST-N80-5[G] >= 4" CLD 23 NBR
9RST-S65[G] >= 4" CLD 23 SBR
Piranha Restraint Gasket[G] >= 4" CLD 23 SBR
Piranha Restraint Gasket[G] >= 4" CLD 23 NBR
Piranha Restraint Gasket (Dual Durometer)[G] >= 4" CLD 23 NBR
Romac-9RST-N80-1 [2] CLD 23 NBR

[1] Certified for a maximum surface area to volume ratio of 2.0 sq. in./L.
[2] Certified for a maximum surface area to volume ratio of 3.4 sq. in./L.
[G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for
    “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state
    laws and the U.S. Safe Drinking Water Act.

    

O-Rings
9RST-N3-3[G] [1] CLD 23 NBR
Romac-9RST-N80-1 [2] CLD 23 NBR

[1] Certified for a maximum surface area to volume ratio of 2.0 sq. in./L.
[2] Certified for a maximum surface area to volume ratio of 3.4 sq. in./L.
[G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for
    “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state
    laws and the U.S. Safe Drinking Water Act.

    



 
RPM Products 
Rubber Plastics & Metal Products Inc.
23272 Arroyo Vista 
Rancho Santa Margarita, CA 92688 
United States 
949-888-8543
Visit this company's website

Facility : # 2 China

Joining and Sealing Materials

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Gasket/Sealing Materials
BN50-61-2 [2] C. HOT NBR
BN60-61-2[4] [2] C. HOT NBR
BN70-61-2 [2] C. HOT NBR
BN75-61-2 [2] C. HOT NBR
BN80-61-2[4] [2] C. HOT NBR
EP65-61-2[4] [1] C. HOT EPDM
EP70-61-2 [1] C. HOT EPDM
EP70-WRC[5] [6] C. HOT EPDM
EP70PC-61-2[3] [1] C. HOT EPDM
EP80-61-2[4] [1] C. HOT EPDM
EP80PC-61-2[3] [1] C. HOT EPDM
EP90PC-61-2[4] [1] C. HOT EPDM
SI60-61-2[3] [1] C. HOT SLC
SI70-61-2[3] [1] C. HOT SLC
SI80-61-2[3] [1] C. HOT SLC

[1] Certified for a maximum surface area to volume ratio of 2.0 sq. in./L.
[2] Certified for a maximum surface area to volume ratio of 1.6 sq. in./L.
[3] This product has also been evaluated for use in Mechanical Plumbing Device applications
    with a maximum surface area to volume ratio of 2.0 sq. in./L.
[4] This product has also been evaluated for use in Mechanical Plumbing Device applications
    with a maximum surface area to volume ratio of 0.2 sq. in./L.
[5] This product has also been evaluated for use in Mechanical Plumbing Device applications
    with a maximum use restriction of 0.1 sq. in./L.
[6] Certified for a maximum surface area to volume ratio of 1.3 sq. in./L.



 
RT Dygert International 
2700 South River Road
Suite 116 
Des Plaines, IL 60018 
United States 
800-423-9272 
847-675-1444
Visit this company's website

Facility : # 2 China

Joining and Sealing Materials

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Gasket/Sealing Materials
E-6006[2] [1] C. HOT EPDM
E-6502[2] [1] C. HOT EPDM
E-7013 [1] C. HOT EPDM
E-7020[3] [1] C. HOT EPDM
E-7039 [1] CLD 23 EPDM
E-8005[2] [1] C. HOT EPDM
E-8006[4] [1] C. HOT EPDM
E-9003[2] [1] C. HOT EPDM
N-5007 [5] C. HOT NBR
N-6010[2] [5] C. HOT NBR
N-7039 [5] C. HOT NBR
N-7503 [5] C. HOT NBR
N-8004[2] [5] C. HOT NBR
S-4005[4] [1] C. HOT SLC
S-6004[4] [1] C. HOT SLC
S-7008[4] [1] C. HOT SLC
S-8002[4] [1] C. HOT SLC

[1] Certified for a maximum surface area to volume ratio of 2.0 sq. in./L.
[2] This product has also been evaluated for use in Mechanical Plumbing Device applications
    with a maximum surface area to volume ratio of 0.2 sq. in./L.
[3] This product has also been evaluated for use in Mechanical Plumbing Device applications
    with a maximum use restriction of 1.1 sq. in./L.
[4] This product has also been evaluated for use in Mechanical Plumbing Device applications
    with a maximum surface area to volume ratio of 2.0 sq.in./L.
[5] Certified for a maximum surface area to volume ratio of 1.6 sq. in./L.



 
RT Dygert International 
2700 South River Road
Suite 116 
Des Plaines, IL 60018 
United States 
847-675-1444
Visit this company's website

Facility : # 1 China

Joining and Sealing Materials

    Water Water
    Contact Contact
Trade Designation Size Temp Material

O-Rings
E-8002[2] [1] C. HOT EPDM
N-7027[3] [1] D. HOT NBR
S-7004 [1] C. HOT SLC

[1] Certified for a maximum surface area to volume ratio of 2.0 sq. in./L.
[2] This product has also been evaluated for use in Mechanical Plumbing Device applications
    with a maximum surface area to volume ratio of 2.0 sq. in./L.
[3] This product has also been evaluated for use in Mechanical Plumbing Device applications
    with a maximum surface area to volume ratio of 0.2 sq. in./L.



 
S & B Technical Products, Inc. / Terramix S.A. 
1300 East Berry Street
Ft. Worth, TX 76119 
United States 
800-432-8213 
817-923-3344

Facility : Fort Worth, TX

Joining and Sealing Materials