NSF Product and Service Listings

[1] Certified for a maximum of 18.5 joints per liter.

[1] Certification is based on a minimum cure of 72 hours at 75°F.

[1] This product has also been evaluated for use in Mechanical Plumbing Device applications
    with a maximum use restriction of 2.0 sq. in./L.
[2] Certified for a maximum surface area to volume ratio of 2.0 sq. in./L.
[3] This product has also been evaluated for use in Mechanical Plumbing Device applications
    with a maximum use restriction of 0.1 sq. in./L.

[1] This product has also been evaluated for use in Mechanical Plumbing Device applications
    with a maximum use restriction of 2.0 sq. in./L.
[2] Certified for a maximum surface area to volume ratio of 2.0 sq. in./L.
[3] This product has also been evaluated for use in Mechanical Plumbing Device applications
    with a maximum use restriction of 0.1 sq. in./L.

[G] Product is Certified to NSF/ANSI/CAN 372 and conforms with the lead content requirements
    for "lead free" plumbing as defined by California, Vermont, Maryland, and Louisiana
    state laws and the U.S. Safe Drinking Water Act.

[1] Certified for a maximum surface area to volume ratio of 40 sq. in./L.

[1] Certified for a maximum surface area to volume ratio of 40 sq. in./L.

[2] Listed models have lot #503311 or greater.

[G] Product is Certified to NSF/ANSI/CAN 372 and conforms with the lead content requirements
    for "lead free" plumbing as defined by California, Vermont, Maryland, and Louisiana
    state laws and the U.S. Safe Drinking Water Act.

[1] Certified for a maximum surface area to volume ratio of 4.0 square inches/L.

[1] Certified for a maximum surface area to volume ratio of 4.0 square inches/L.

[2] Certified for a maximum surface area to volume ratio of 2.0 sq. in./L.
[3] This product has also been evaluated for use in Mechanical Plumbing Device applications
    with a maximum surface area to volume ratio of 1.0 sq. in./L.

[1] Certified for a maximum surface area to volume ratio of 1.0 sq. in./L.
[2] Certified for a maximum surface area to volume ratio of 2.0 sq. in./L.
[3] This product has also been evaluated for use in Mechanical Plumbing Device applications
    with a maximum surface area to volume ratio of 1.0 sq. in./L.

[1] This product has also been evaluated for use in Mechanical Plumbing Device applications
    with a maximum use restriction of 6.0 sq. in./L.
[2] Certified for a maximum surface area to volume ratio of 6.0 sq. in./L.
[3] Certified for a maximum surface area to volume ratio of 2.0 sq. in./L.
[4] This product has also been evaluated for use in Mechanical Plumbing Device applications
    with a maximum surface area to volume ratio of 1.0 sq. in./L.
[5] Certified for a maximum surface area to volume ratio of 5.0 sq. in./L.
[6] This product has also been evaluated for use in Mechanical Plumbing Device applications
    with a maximum use restriction of 3.4 sq. in./L.
[7] Certified for a maximum surface area to volume ratio of 3.4 sq. in./L

[1] This product has also been evaluated for use in Mechanical Plumbing Device applications
    with a maximum use restriction of 6.0 sq. in./L.
[2] Certified for a maximum surface area to volume ratio of 6.0 sq. in./L.
[3] Certified for a maximum surface area to volume ratio of 2.0 sq. in./L.
[4] This product has also been evaluated for use in Mechanical Plumbing Device applications
    with a maximum surface area to volume ratio of 1.0 sq. in./L.
[5] Certified for a maximum surface area to volume ratio of 5.0 sq. in./L.
[6] This product has also been evaluated for use in Mechanical Plumbing Device applications
    with a maximum use restriction of 3.4 sq. in./L.
[7] Certified for a maximum surface area to volume ratio of 3.4 sq. in./L

[1] Certified for a maximum surface area to volume ratio of 2.0 square inches/L.
[2] This product has also been evaluated for use in Mechanical Plumbing Device applications
    with a maximum use restriction of 2.0 square inches/L.
[3] Certified for a maximum surface area to volume ratio of 6.0 square inches/L.
[4] This product has also been evaluated for use in Mechanical Plumbing Device applications
    with a maximum use restriction of 6.0 square inches/L.

[1] Certified for a maximum surface area to volume ratio of 2.0 square inches/L.
[2] This product has also been evaluated for use in Mechanical Plumbing Device applications
    with a maximum use restriction of 2.0 square inches/L.
[3] Certified for a maximum surface area to volume ratio of 6.0 square inches/L.
[4] This product has also been evaluated for use in Mechanical Plumbing Device applications
    with a maximum use restriction of 6.0 square inches/L.

[1] Certified for a maximum surface area to volume ratio of 2.0 sq. in./L.
[3] This product has also been evaluated for use in Mechanical Plumbing Device applications
    with a maximum surface area to volume ratio of 3.4 sq. in./L
[4] Certified for a maximum surface area to volume ratio of 3.4 sq. in./L
[5] Certified for a maximum surface area to volume ratio of 2.0 square inches/L.
[6] This product has been evaluated for use in Mechanical Plumbing Device applications with
    a maximum use restriction of 6.0 sq. in/L.
[7] Certified for a maximum surface area to volume ratio of 6.0 sq. in./L.
[8] This product has also been evaluated for use in Mechanical Plumbing Device applications
    with a maximum use restriction of 0.15 sq. in./L.
[9] Certified for a maximum surface area to volume ratio of 1.5 sq. in./L.
[10] Certified for a maximum surface area to volume ratio of 5.0 sq. in./L.
[11] Certified for a maximum surface area to volume ratio of 0.60 sq. in/L.
[12] This product has also been evaluated for use in Mechanical Plumbing Device applications
     with a maximum use restriction of 2.0 square inches/L.

[1] Certified for a maximum surface area to volume ratio of 2.0 sq. in./L.
[3] This product has also been evaluated for use in Mechanical Plumbing Device applications
    with a maximum surface area to volume ratio of 3.4 sq. in./L
[4] Certified for a maximum surface area to volume ratio of 3.4 sq. in./L
[5] Certified for a maximum surface area to volume ratio of 2.0 square inches/L.
[6] This product has been evaluated for use in Mechanical Plumbing Device applications with
    a maximum use restriction of 6.0 sq. in/L.
[7] Certified for a maximum surface area to volume ratio of 6.0 sq. in./L.
[10] Certified for a maximum surface area to volume ratio of 5.0 sq. in./L.

[1] Formerly Loctite Resinol RTC.
[2] Certified for use with or without Loctite IS 7102 Accelerator.  This product has not
    been evaluated with any other activator or accelerator.
[3] Maximum use level for residential applications is 31 sq. in./L (335 sq. in. per
    residence).

[4] Formerly Loctite 513 Dri-Seal.
[5] Formerly Loctite 513HV Dri-Seal.

[1] Certified for use with pipes >=1/4".

[1] Only products bearing the NSF Mark on the product, product packaging, and/or
    documentation shipped with the product are Certified.
[2] Certified for a maximum use of 2 joints/liter.
[3] Certification does not include activators.

[1] Only products bearing the NSF Mark on the product, product packaging, and/or
    documentation shipped with the product are Certified.
[7] Maximum of 21 joints per residence (2 joints per liter).
[8] Formerly Stainless Steel PST 567.
[9] Certified for use as an anode thread sealant in water heater tanks with a maximum
    surface area to volume ratio of 0.08 sq. in./L.

[5] Certified for a maximum use of 10 joints/liter.

[4] Certified for a maximum use of 10 joints/liter.

[1] Certified for a maximum surface area to volume ratio of 50 square inches per liter.
[2] Impregnation allowable on castings exhibiting a maximum leakage of 450 cc's when tested
    at 60 PSI air pressure.
[3] Also evaluated as material for use in Mechanical Plumbing Devices (Section 9) for
    applications with a maximum surface area of 50 square inches per liter.
[4] Certified for use in materials with a porosity rating of less than 1 percent.

[G] Product is Certified to NSF/ANSI/CAN 372 and conforms with the lead content requirements
    for "lead free" plumbing as defined by California, Vermont, Maryland, and Louisiana
    state laws and the U.S. Safe Drinking Water Act.

[1] Certification is based on a minimum cure of 72 hours at 75°F.

[1] Mix ratio of Part A:Part B is 1:1

[2] Certification is based on a minimum cure of 72 hours at 75°F.

[G] Product is Certified to NSF/ANSI/CAN 372 and conforms with the lead content requirements
    for "lead free" plumbing as defined by California, Vermont, Maryland, and Louisiana
    state laws and the U.S. Safe Drinking Water Act.

[1] Evaluated for use as a thread compound in:
    Drill collars/tool joints >=4 1/2"
    Tubing >=2 3/8"
    Well casings >=4 1/2"
[2] Certified for use on pipes 1/2" and greater.
[G] Product is Certified to NSF/ANSI/CAN 372 and conforms with the lead content requirements
    for "lead free" plumbing as defined by California, Vermont, Maryland, and Louisiana
    state laws and the U.S. Safe Drinking Water Act.

[1] Only products bearing the NSF Mark on the product, product packaging, and/or
    documentation shipped with the product are Certified.

[G] Product is Certified to NSF/ANSI/CAN 372 and conforms with the lead content requirements
    for "lead free" plumbing as defined by California, Vermont, Maryland, and Louisiana
    state laws and the U.S. Safe Drinking Water Act.

[2] Listed models have lot #503311 or greater.
[3] Certified for the following colors: blue, gold, and white.

[1] Minimum cure time is 0.25 hours at 40°F. Mix ratio of Resin:Accelerator is 90:10 by
    volume.
[2] MasterRoc MP 351 LV Accelerator is only certified for use with MasterRoc MP 351 LV.
[3] Certified for use in tanks at maximum surface area to volume ratio of 0.19 square
    centimeters per liter.

[1] Minimum cure time is 0.25 hours at 40°F.  Mix ratio of Resin:Accelerator is 90:10 by
    volume.
[2] MasterRoc MP 355 1K Accelerator is only certified for use with MasterRoc MP 355 1K.
[3] Certified for use in tanks at maximum surface area to volume ratio of 0.26 square
    centimeters per liter. 

[G] Product is Certified to NSF/ANSI/CAN 372 and conforms with the lead content requirements
    for "lead free" plumbing as defined by California, Vermont, Maryland, and Louisiana
    state laws and the U.S. Safe Drinking Water Act.

[1] Only products bearing the NSF Mark on the product, product packaging, and/or
    documentation shipped with the product are Certified.

[G] Product is Certified to NSF/ANSI/CAN 372 and conforms with the lead content requirements
    for "lead free" plumbing as defined by California, Vermont, Maryland, and Louisiana
    state laws and the U.S. Safe Drinking Water Act.

[1] Only products bearing the NSF Mark on the product, product packaging, and/or
    documentation shipped with the product are Certified.
[2] This product has also been evaluated for use in Mechanical Plumbing Device applications
    with a maximum use restriction of 0.2 sq. in./L.
[3] Certified for a maximum surface area to volume ratio of 2.0 sq. in./L.
[4] Certified for a maximum surface area to volume ratio of 0.2 square inches/L.
[5] This product has also been evaluated for use in Mechanical Plumbing Device applications
    with a maximum use restriction of 2.5 sq. in./L.
[6] Certified for a maximum surface area to volume ratio of 2.5 sq. in./L.
[7] This product has also been evaluated for use in Mechanical Plumbing Device applications
    sq. in./L with a maximum use restriction of 2.0

[1] Only products bearing the NSF Mark on the product, product packaging, and/or
    documentation shipped with the product are Certified.
[2] This product has also been evaluated for use in Mechanical Plumbing Device applications
    with a maximum use restriction of 0.2 sq. in./L.
[3] Certified for a maximum surface area to volume ratio of 2.0 sq. in./L.
[4] Certified for a maximum surface area to volume ratio of 0.2 square inches/L.
[5] This product has also been evaluated for use in Mechanical Plumbing Device applications
    with a maximum use restriction of 2.5 sq. in./L.
[6] Certified for a maximum surface area to volume ratio of 2.5 sq. in./L.
[7] This product has also been evaluated for use in Mechanical Plumbing Device applications
    sq. in./L with a maximum use restriction of 2.0

[2] Certified for a maximum surface area to volume ratio of 2.0 sq. in./L.

[1] Certified for a maximum of 1 joint per liter or (10) 1/2" joints per residence.
[2] Certified for a maximum of 1.5 joints per liter or (16) 1/2" joints per residence.

[1] Products were prepared for evaluation according to manufacturer's instructions.
[2] DuPont Registered Trademark.
[G] Product is Certified to NSF/ANSI/CAN 372 and conforms with the lead content requirements
    for "lead free" plumbing as defined by California, Vermont, Maryland, and Louisiana
    state laws and the U.S. Safe Drinking Water Act.

[1] Diaphragms are Certified for use in valves.
[2] Certified for a maximum surface area to volume ratio of 2 sq. in./L.

[2] Certified for a maximum surface area to volume ratio of 2 sq. in./L.

[2] Certified for a maximum surface area to volume ratio of 2 sq. in./L.

[1] Certified for use with metallic materials having no greater than 10% porosity. 
[2] Certified for the following impregnation process/cure (Catalyst must be added at
    0.05-0.4% by weight to the sealant just prior to dry vacuum process):
    
    Step 1: Dry Vacuum 
    Step 2: Wet Vacuum 
    Step 3: Draining of the castings in a drain chamber or a centrifuge (15-20 minutes). 
    Step 4: Cold water wash of the castings (minimum 15 degrees Celsius for 15-20 minutes). 
    Step 5: Hot Water curing of the castings by dipping them in hot water at 90 - 95 deg C
    for 10 minutes.
[3] Certified for a maximum surface area to volume ratio of 50 square inches per liter.

[1] Certified for a maximum surface area to volume ratio of 2.0 sq. in./L.
[G] Product is Certified to NSF/ANSI/CAN 372 and conforms with the lead content requirements
    for "lead free" plumbing as defined by California, Vermont, Maryland, and Louisiana
    state laws and the U.S. Safe Drinking Water Act.

[1] Certified for a maximum surface area to volume ratio of 2.0 sq. in./L.
[G] Product is Certified to NSF/ANSI/CAN 372 and conforms with the lead content requirements
    for "lead free" plumbing as defined by California, Vermont, Maryland, and Louisiana
    state laws and the U.S. Safe Drinking Water Act.

[1] All models use a suffix designation to indicate the size of product.
[2] Certification is based on a minimum cure of 72 hours at 75°F.

[2] Certification is based on a minimum cure of 72 hours at 75°F.