NSF Product and Service Listings

[1] Certified for use as an anchoring adhesive for installing thread rods (less than or
    equal to 1.3 inches in diameter) in concrete or masonry for water treatment applications.

[1] Certified for use as an anchoring adhesive for installing threaded rods (less than or
    equal to 6 mm - 36 mm or 1/4" - 1-3/8" in diameter) in concrete for water treatment
    applications.

[1] Certified for use as an anchoring adhesive for installing thread rods (less than or
    equal to 1.3 inches in diameter) in concrete or masonry for water treatment applications.

[1] Certified for use as an anchoring adhesive for installing thread rods (less than or
    equal to 1.3 inches in diameter) in concrete or masonry for water treatment applications.

[1] Certified for use as an anchoring adhesive for installing thread rods (less than or
    equal to 1.3 inches in diameter) in concrete or masonry for water treatment applications.

[1] Only products bearing the NSF Mark on the product, product packaging, and/or
    documentation shipped with the product are Certified.

[1] Certified for use as an anchoring adhesive for installing thread rods (less than or
    equal to 1.3 inches in diameter) in concrete or masonry for water treatment applications.

[1] Certified for use as an anchoring adhesive for installing thread rods (less than or
    equal to 1.3 inches in diameter) in concrete or masonry for water treatment applications.

[1] Certified or use as an anchoring adhesive for installing thread rods (less than or equal
    to 1.3 inches in diameter) in concrete or masonry for water treatment applications.

[1] Certified for use as an anchoring adhesive for installing threaded rods (less than or
    equal to 36mm in diameter) in concrete for water treatment applications.
[2] Certified for use as an anchoring adhesive for installing threaded rods (less than or
    equal to 6 mm - 36mm in diameter) in concrete for water treatment applications.

[1] Mix ratio is 100:50 (A:B) by volume or 100:62.5 (A:B) by weight.  Minimum cure time is 7
    days at 77°F then 3 hours at 158°F.
[2] Mix ratio is 100:100 (A:B) by volume or 100:110 (A:B) by weight with a maximum dry film
    thickness of 50 mils.  Minimum cure time is 7 days at 77°F then 3 hours at 158°F
[3] Certified for a maximum surface area to volume ratio of 7.26 sq. in/L.
[G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for
    “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state
    laws and the U.S. Safe Drinking Water Act.

    

[1] Mix ratio:
    By weight: 0.9 Part A:1.0 Part B
    By volume: 100 Part A:100 Part B
    Product cure: Minimum cure time is 7 days at 77°F.
[2] Certified for a maximum surface area to volume ratio of 20 sq. in./L in spiral-wound
    filter elements with a minimum daily flow of 12,000 liters per day.
[3] Mix ratio:
    By weight: 1.0 Part A: 1.1 Part B
    By volume: 1 Part A: 1 Part B
    Product cure: Minimum cure time is 7 days at 77°F.

[1] Mix ratio of Loctite CR 3700 : CR 4200 is 100:61 parts by Weight or 2:1 by Volume.
[2] Minimum cure time 14 days at room temperature.
[3] Only products bearing the NSF Mark on the product, product packaging, and/or
    documentation shipped with the product are Certified.

[1] Minimum cure time is 7 days.
[2] Formerly Macroplast UK 178A and 178B.
[3] Mix ratio is 1:1 (A:B) by volume.

[1] Mix ratio is 1:1 (A:B) by weight or volume.
[2] Certification does not include use with Primer 2000.
[3] Formerly Loctite Speedbonder H3101.
[4] Certified for joining pipes and fittings 4 inches and greater.
[5] Evaluated for use with Henkel Loctite's anaerobic adhesives and sealants.
[6] Only products bearing the NSF Mark on the product, product packaging, and/or
    documentation shipped with the product are Certified.
[7] Formerly Loctite 7649 Primer N.

[1] Mix ratio is 1:1 (A:B) by volume.
[2] Minimum cure time is 7 days.

[1] Certified for use without activators.
[2] Certified for a maximum of 10 joints per liter.

[1] Only products bearing the NSF Mark on the product, product packaging, and/or
    documentation shipped with the product are Certified.
[2] Certified for a maximum use of 2 joints/liter.
[3] Certification does not include activators.

[1] Certified for use as an anchoring adhesive for installing thread rods (less than or
    equal to 1.3 inches in diameter) in concrete or masonry for water treatment applications.

[1] Mix Ratio is 1:1 (A:B) by volume or 0.9:1 (A:B) by weight.
[2] Minimum cure time is 7 days.

[1] The product has also been evaluated for use in Mechanical Plumbing Device applications.
    Certification does not include a primer.

[1] Product is Certified for use as an anchoring adhesive for installing threaded rods (less
    than or equal to 1.3 inches in diameter) in concrete for water treatment applications.
[2] Certified for use as an anchoring adhesive for installing threaded rods (less than or
    equal to 24 mm in diameter) in concrete or masonry for water treatment applications. 
    Mix ratio of Part A:Part B is 3:1 by volume.
[3] Certified for use as an anchoring adhesive for installing threaded rods in concrete or
    masonry for water treatment applications. Certified for a maximum surface area to volume
    ratio of 0.00006 sq. in./L
[4] Certified for use as an anchoring adhesive for installing threaded rods (less than or
    equal to 40 mm in diameter) in concrete for water treatment applications.
[5] Certified for use as an anchoring adhesive for installing threaded rods (less than or
    equal to 32 mm in diameter) in concrete for water treatment applications.
[6] Certified for use as an anchoring adhesive for installing screw anchors in concrete for
    water treatment applications. KHC is certified for use with screw anchors less than or
    equal to 20 mm in diameter. HUS4-MAX is certified for use with screw anchors less than
    or equal to 16 mm in diameter.

[1] Certification is based on a minimum cure of 72 hours at 75°F

[1] Certified for a maximum use level of 7.27 sq. in/L.
[2] Mix ratio is 1:1 (A:B) by volume and 0.89:1 (A:B) by weight.
[3] Minimum cure time and temperature is 7 days at 75°F.
[4] Mix ratio of Part A:B is 3:1 by volume or 2.58:1 by weight

[1] Mix ratio is 1:1 (A:B) by volume and 0.89:1 (A:B) by weight.
[2] Minimum cure time and temperature is 7 days at 75°F.
[3] Certified for a maximum use level of 7.27 sq. in/L.

[1] Certified for use as an anchoring adhesive for installing thread rods (less than or
    equal
    to 1.3 inches in diameter) in concrete or masonry for water treatment applications.

[1] Certified for use at a maximum surface area to volume ratio of 0.0005 square inches per
    liter in a tank.

[1] Certified for use at a maximum surface area to volume ratio of 0.0005 square inches per
    liter in a tank.

[1] Product requires a minimum 24 hour cure.
[2] Certification is based on a minimum cure of 72 hours at 75°F.

[1] Only products bearing the NSF Mark on the product, product packaging, and/or
    documentation shipped with the product are Certified.
[1] Only products bearing the NSF Mark on the product, product packaging, and/or
    documentation shipped with the product are Certified.
[2] Product requires a minimum 24 hour cure.
[3] Certification is based on a minimum cure of 72 hours at 75ºF.

[1] Mix ratio is 1:1.15 Part A:Part B by weight.
    Product requires cure of 8 hours at 25°C.
[2] Certified for a maximum surface area to volume ratio of 7.27 in2/L.

[1] Digits next to the trade name refers to the product volume in (ml).
[2] Certified for use as an anchoring adhesive for installing thread rods (less than or
    equal to 1.3 inches in diameter) in concrete or masonry for water treatment applications.

[1] Certified for use as an anchoring adhesive for installing thread rods (less than or
    equal to 1.3 inches in diameter) in concrete or masonry for water treatment applications.

[1] 8000 Series Adhesive and Hardener includes the following trade names: DS-8014, DS-8024,
    DS-8069, DS-8071, DS-8088-S, DS-8088-L, and DS-8069-C.
[2] Mix ratio is 7.6:1 (A:B) by weight but will vary slightly based on the kit size. 
    Minimum cure time is 1 hour at 100° F.  Please follow the manufacturer’s instructions
    supplied with each kit.
[3] Mix ratio is 3.2:1 (A:B) by weight.  Minimum cure time is 1 hour at 100° F.  The mix
    ratios will vary slightly based on the kit size.  Please follow the manufacturer’s
    instructions supplied with each kit.
[4] Mix ratio is 3.2:1 (A:B) by weight.  Minimum cure time is 1 hour at 110° F.  The mix
    ratios will vary slightly based on the kit size.  Please follow the manufacturer’s
    instructions supplied with each kit.
[5] Mix ratio of adhesive to hardener is 100:26.62 (A:B) by weight. Minimum cure time is 35
    minutes at 77° F. Please follow the manufacturer’s instructions supplied with each kit.
[6] Mix ratio is 3.2:1 (A:B) by weight.  Minimum cure time is 3 hours at 100° F.  The mix
    ratios will vary slightly based on the kit size.  Please follow the manufacturer’s
    instructions supplied with each kit.
[7] Mix ratio is 45:1 (A:B) by weight.  Minimum cure time is 24 hours at 71 - 100° F.  The
    mix ratios will vary slightly based on the kit size.  Please follow the manufacturer’s
    instructions supplied with each kit.

[1] Mix ratio is 100:62.5 (A:B) by weight.
[2] Minimum cure time is 24 hours at 77°F.
[3] Certified for a maximum surface area to volume ratio of 7.26 sq. in./L.

[1] Only products bearing the NSF Mark on the product, product packaging, and/or
    documentation shipped with the product are Certified.

[1] Certified for use as an anchoring adhesive for installing thread rods (less than or
    equal to 1.3 inches in diameter) in concrete or masonry for water treatment applications.

[1] Mix ratio: 62.5:100 Part A:B by weight. This product must be cured for 24 hours at 23°C,
    followed by 24 hours at 60°C.
[2] Certified for a maximum surface area to volume ratio of 20 sq. in./L in spiral-wound
    filter elements with a minimum daily flow of 12,000 liters per day.

[1] Minimum cure time is 7 days.
    Mix ratio is 1:1 (A:B) by volume.
[G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for
    “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state
    laws and the U.S. Safe Drinking Water Act.

    

[1] Product requires cure of 7 days at 23°C and 50% relative humidity.
[2] Certified for a maximum use level of 0.2 square inches per liter.
[3] Product requires cure of 7 days at 23°C.

[1] Certified for a maximum exposed surface area of 25 sq. in./1000 gal.
[2] Certified for a maximum exposed surface area of 216 sq. in./1000 gal.

[1] Certified for use as an anchoring adhesive for installing thread rods (less than or
    equal to 1.3 inches in diameter) in concrete or masonry for water treatment applications.

[1] Certified for use as an anchoring adhesive for installing thread rods (less than or
    equal to 1.3 inches in diameter) in concrete or masonry for water treatment applications.

[1] Certified for use as an anchoring adhesive for installing thread rods (less than or
    equal to 1.3 inches in diameter) in concrete or masonry for water treatment applications.

[1] Only products bearing the NSF Mark on the product, product packaging, and/or
    documentation shipped with the product are Certified.

[1] Certified for use as an anchoring adhesive for installing thread rods (less than or
    equal to 1.3 inches in diameter) in concrete or masonry for water treatment applications.

[1] Certified for use as an anchoring adhesive for installing thread rods (less than or
    equal to 1.3 inches in diameter) in concrete or masonry for water treatment applications.

[1] All models use a suffix designation to indicate the size of product.
[2] Certification is based on a minimum cure of 72 hours at 75°F.