NSF Product and Service Listings

These NSF Official Listings are current as of Monday, May 27, 2019 at 12:15 a.m. Eastern Time. Please contact NSF to confirm the status of any Listing, report errors, or make suggestions.

Alert: NSF is concerned about fraudulent downloading and manipulation of website text. Always confirm this information by clicking on the below link for the most accurate information: http://info.nsf.org/Certified/PwsComponents/Listings.asp?



NSF/ANSI 61
Drinking Water System Components - Health Effects

NOTE: Unless otherwise indicated for Materials, Certification is only for the Water Contact Material shown in the Listing. Click here for a list of Abbreviations used in these Listings. Click here for the definitions of Water Contact Temperatures denoted in these Listings.


 
3M / Electrical Markets Division 
3M Center, Building 201-2C-11
St. Paul, MN 55144 
United States 
651-736-9030
Visit this company's website


Facility : Angleton, TX

Protective (Barrier) Materials

    Water Water
  Water Contact Contact Contact
Trade Designation Size Restriction Temp Material

Coatings - Fittings
3M Scotchkote Fusion Bonded Epoxy Coating 6233W 11G[1] >= 1/2" D. HOT PEC
3M Scotchkote Fusion Bonded Epoxy Coating 6233W 4G[1] >= 1/2" D. HOT PEC
3M Scotchkote Fusion Bonded Epoxy Coating 6233W 8G[1] >= 1/2" D. HOT PEC
Scotchkote 206N[2] >= 4" D. HOT PEC
Scotchkote 206N Extra LG[2] >= 4" D. HOT PEC
Scotchkote 206N Fluid Bed[2] >= 4" D. HOT PEC
Scotchkote 206N Long Gel[2] >= 4" D. HOT PEC

[1] Colors: Dark Green
    Number of Coats: 1
    Maximum Field Use Dry Film Thickness (in mils): 50
    Maximum thinner: None
    Final Cure Time and Temperature: 6233W 4G: 30-45 seconds at 450°F; 6233W 8G: 60-90
    seconds at 450°F; 6233W 11G: 90-120 seconds at 450°F
    Special Comments: Preheat part to 425° - 488° F before application of powder.
[2] Number of Coats: 1
    Maximum Field Use Dry Film Thickness (in mils): 60
    Final Cure Time and Temperature: 206N: 10 minutes at 400°F; 206N Extra LG: 16 minutes at
    400°F; 206N Fluid Bed: 10 minutes at 400°F; 206N Long Gel: 10 minutes at 400°F

Coatings - Pipe
3M Scotchkote Fusion Bonded Epoxy Coating 6233W 11G[1] >= 1/2" D. HOT PEC
3M Scotchkote Fusion Bonded Epoxy Coating 6233W 4G[1] >= 1/2" D. HOT PEC
3M Scotchkote Fusion Bonded Epoxy Coating 6233W 8G[1] >= 1/2" D. HOT PEC
Scotchkote 206N[2] >= 4" D. HOT PEC
Scotchkote 206N Extra LG[2] >= 4" D. HOT PEC
Scotchkote 206N Fluid Bed[2] >= 4" D. HOT PEC
Scotchkote 206N Long Gel[2] >= 4" D. HOT PEC

[1] Colors: Dark Green
    Number of Coats: 1
    Maximum Field Use Dry Film Thickness (in mils): 50
    Maximum thinner: None
    Final Cure Time and Temperature: 6233W 4G: 30-45 seconds at 450°F; 6233W 8G: 60-90
    seconds at 450°F; 6233W 11G: 90-120 seconds at 450°F
    Special Comments: Preheat part to 425° - 488° F before application of powder.
[2] Number of Coats: 1
    Maximum Field Use Dry Film Thickness (in mils): 60
    Final Cure Time and Temperature: 206N: 10 minutes at 400°F; 206N Extra LG: 16 minutes at
    400°F; 206N Fluid Bed: 10 minutes at 400°F; 206N Long Gel: 10 minutes at 400°F

Coatings - Pump
Scotchkote 206N[2] [3] >= 2" D. HOT PEC
Scotchkote 206N Extra LG[2] [3] >= 2" D. HOT PEC
Scotchkote 206N Fluid Bed[2] [3] >= 2" D. HOT PEC
Scotchkote 206N Long Gel[2] [3] >= 2" D. HOT PEC

[2] Number of Coats: 1
    Maximum Field Use Dry Film Thickness (in mils): 60
    Final Cure Time and Temperature: 206N: 10 minutes at 400°F; 206N Extra LG: 16 minutes at
    400°F; 206N Fluid Bed: 10 minutes at 400°F; 206N Long Gel: 10 minutes at 400°F
[3] Certified for a maximum surface area to volume ratio of 122.1 sq. in./L. for pump end
    use.

Coatings - Tank
Scotchkote 206N[2] >= 5 gal. D. HOT PEC
Scotchkote 206N Extra LG[2] >= 5 gal. D. HOT PEC
Scotchkote 206N Fluid Bed[2] >= 5 gal. D. HOT PEC
Scotchkote 206N Long Gel[2] >= 5 gal. D. HOT PEC

[2] Number of Coats: 1
    Maximum Field Use Dry Film Thickness (in mils): 60
    Final Cure Time and Temperature: 206N: 10 minutes at 400°F; 206N Extra LG: 16 minutes at
    400°F; 206N Fluid Bed: 10 minutes at 400°F; 206N Long Gel: 10 minutes at 400°F

Coatings - Valve
3M Scotchkote Fusion Bonded Epoxy Coating 6233W 11G[1] >= 1/2" D. HOT PEC
3M Scotchkote Fusion Bonded Epoxy Coating 6233W 4G[1] >= 1/2" D. HOT PEC
3M Scotchkote Fusion Bonded Epoxy Coating 6233W 8G[1] >= 1/2" D. HOT PEC
Scotchkote 206N[2] >= 2" D. HOT PEC
Scotchkote 206N Extra LG[2] >= 2" D. HOT PEC
Scotchkote 206N Fluid Bed[2] >= 2" D. HOT PEC
Scotchkote 206N Long Gel[2] >= 2" D. HOT PEC

[1] Colors: Dark Green
    Number of Coats: 1
    Maximum Field Use Dry Film Thickness (in mils): 50
    Maximum thinner: None
    Final Cure Time and Temperature: 6233W 4G: 30-45 seconds at 450°F; 6233W 8G: 60-90
    seconds at 450°F; 6233W 11G: 90-120 seconds at 450°F
    Special Comments: Preheat part to 425° - 488° F before application of powder.
[2] Number of Coats: 1
    Maximum Field Use Dry Film Thickness (in mils): 60
    Final Cure Time and Temperature: 206N: 10 minutes at 400°F; 206N Extra LG: 16 minutes at
    400°F; 206N Fluid Bed: 10 minutes at 400°F; 206N Long Gel: 10 minutes at 400°F



Facility : Morden, Manitoba, Canada

Protective (Barrier) Materials

    Water Water
  Water Contact Contact Contact
Trade Designation Size Restriction Temp Material

Coatings - Fittings
ScotchKote 134[1] >= 1/2"[2] D. HOT PEC

[1] Number of Coats: 1
    Sequence of Coats: N/A
    Maximum Field Use Dry Film Thickness (in mils): 60
    Maximum Thinner: None
    Final Cure Time and Temperature: 25 minutes at 425° F
[2] Certified for a maximum surface area to volume ratio of 122.1 sq. in./L. for pump end
    use.

Coatings - Pipe
ScotchKote 134[1] >= 1/2"[2] D. HOT PEC

[1] Number of Coats: 1
    Sequence of Coats: N/A
    Maximum Field Use Dry Film Thickness (in mils): 60
    Maximum Thinner: None
    Final Cure Time and Temperature: 25 minutes at 425° F
[2] Certified for a maximum surface area to volume ratio of 122.1 sq. in./L. for pump end
    use.

Coatings - Pump
ScotchKote 134[1] [2] D. HOT PEC

[1] Number of Coats: 1
    Sequence of Coats: N/A
    Maximum Field Use Dry Film Thickness (in mils): 60
    Maximum Thinner: None
    Final Cure Time and Temperature: 25 minutes at 425° F
[2] Certified for a maximum surface area to volume ratio of 122.1 sq. in./L. for pump end
    use.

Coatings - Tank
ScotchKote 134[1] >= 5 gal. D. HOT PEC

[1] Number of Coats: 1
    Sequence of Coats: N/A
    Maximum Field Use Dry Film Thickness (in mils): 60
    Maximum Thinner: None
    Final Cure Time and Temperature: 25 minutes at 425° F

Coatings - Valve
ScotchKote 134[1] >= 1/2"[2] D. HOT PEC

[1] Number of Coats: 1
    Sequence of Coats: N/A
    Maximum Field Use Dry Film Thickness (in mils): 60
    Maximum Thinner: None
    Final Cure Time and Temperature: 25 minutes at 425° F
[2] Certified for a maximum surface area to volume ratio of 122.1 sq. in./L. for pump end
    use.



 
3R Valve, LLC 
29299 Madison Road
Echo, OR 97826 
United States 
541-376-8107
Visit this company's website


Facility : Echo, OR

Mechanical Devices

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Valves [G]
ASR (Aqua System Recovery) Valve[1] 5" - 14" CLD 23 MLTPL

[1] Certified for a minimum flow of 250 gallons per day.
    Not intended for residential use.
[G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for
    “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state
    laws and the U.S. Safe Drinking Water Act.

    



5Elem Hi-Tech Corporation 
No. 986, Machang Road
Economic Development Zone 
Jiangyan, Jiangsu 225500 
China 
86 523 8881 5055 
Visit this company's website


Facility : Jiangsu, China

Pipes and Related Products

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Pipe
Aquaflow 3/4" - 12" CLD 23 PUR



 
7.30 Inc. 
68 Continental Court B9
P.O. Box 2098 
Breckenridge, CO 80424 
United States 
970-453-6176


Facility : # 1 USA

Protective (Barrier) Materials

    Water Water
  Water Contact Contact Contact
Trade Designation Size Restriction Temp Material

Pipe Liner - Immediate Return to Service[1]
Western Pipeway Tape >= 3" CLD 23 PE

[1] Certification does not include the cement grout used to secure the liner to the pipe.
    Certified for the polyethylene liner only.
    Flush with water for 3-5 gallons per minute for 1 hour required before placing lined
    pipes back into service.



 
7507852 Canada Inc. DBA Next Polymers 
340 Churchill Road
Prescott, ON K0E 1T0 
Canada 
613-925-4281
Visit this company's website


Facility : Prescott, Ontario, Canada

Pipes and Related Products

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Pipe Only
Aqualoc[1] >= 1/2" CLD 23 PVC
Rehau Proloc[2] >= 1/2" CLD 23 PVC

[1] Certified for the following colors: blue, gray, and white.
[2] Certified for the following colors: gray and white



 
A Touch of Brass 
13832 Magnolia Avenue
Chino, CA 91710 
United States 
909-464-1000
Visit this company's website


Facility : Chino, CA

Mechanical Plumbing Devices

Trade Designation      

Commercial Faucets[1] [G]
01280      
01281      
01282      
01283      

[1] Suffix - xx indicates finish.
[G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for
    “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state
    laws and the U.S. Safe Drinking Water Act.

    

Faucets[1] [G]
02017      
02121      
02122      
02356      
05253      

[1] Suffix - xx indicates finish.
[G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for
    “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state
    laws and the U.S. Safe Drinking Water Act.

    

Faucet Hose and Spray Assembly[1] [G]
02124      
02801      
02854      

[1] Suffix - xx indicates finish.
[G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for
    “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state
    laws and the U.S. Safe Drinking Water Act.

    



 
A-S America Inc. (American Standard Brands) 
1 Centennial Avenue
Piscataway, NJ 08854 
United States 
732-369-4061


Facility : # 1 Italy

Mechanical Plumbing Devices

Trade Designation      

Faucets[G]

Single Lever Basin Mixer
D35109.100.100      
D35109.100.144      
D35109.100.243      
D35109.10C.100[1]      
D35109.10C.144[1]      
D35109.10C.243[1]      
D35109.150.100      
D35109.150.144      
D35109.150.243      
D35109.151.100[1]      
D35109.151.144[1]      
D35109.151.243[1]      
D35109.152.100[1]      
D35109.152.144[1]      
D35109.152.243[1]      
D35109.15C.100[1]      
D35109.15C.144[1]      
D35109.15C.243[1]      

[1] Flow rate of 1.2 gpm.

Single Lever Sink Mixer
D35409.000.100      
D35409.000.355      

Single Lever Sink Mixer with Pull-Out Shower
D35409.300.100      
D35409.300.355      

Wall Mounted Basin Mixer
D35109.400.100      
D35109.400.144      
D35109.400.243      

[G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for
    “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state
    laws and the U.S. Safe Drinking Water Act.

    



 
A. O. Smith Enterprises Ltd. 
768 Erie Street
P.O. Box 310 
Stratford, ON N5A 6T3 
Canada 
519-271-5800


Facility : Stratford, Ontario, Canada

Mechanical Devices

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Pressurized Water Storage Tanks[1] [G]
A O Smith ProMax (PM Prefix) 14 - 119 gal. CLD 23 MLTPL
Altamira Pro X/XL 20 - 119 gal. CLD 23 MLTPL
American Water Heater (APT Prefix) 14 - 119 gal. CLD 23 MLTPL
Driller Services (DST/DSI Prefix) >= 65 gal. CLD 23 MLTPL
Global Pump (GPE Prefix) >= 85 gal. CLD 23 MLTPL
Gould Pumps Hydro Pro Water Systems Tanks (V Prefix and MP or PST Suffix) 14 - 20 gal. CLD 23 MLTPL
Gould Pumps Hydro Pro Water Systems Tanks (V Prefix) 14 - 119 gal. CLD 23 MLTPL
PermaTank (SBD/SBDT Prefix) >= 86 gal. CLD 23 MLTPL
Pump Pro (PP Prefix and MP or PST Suffix) 14 - 20 gal. CLD 23 MLTPL
Pump Pro (PP Prefix) >= 14 gal. CLD 23 MLTPL
Trident (TD Prefix and MP or PST Suffix) 14 - 20 gal. CLD 23 MLTPL
Trident Ultra (TDU Prefix and MP or PST Suffix ) >= 14 gal. CLD 23 MLTPL
Trident Ultra (TDU and TD Prefix) >= 14 gal. CLD 23 MLTPL
Xylem CentriPro T Water Sytem Tanks 14 - 119 gal. CLD 23 MLTPL
Xylem CentriPro TP Water Systems Tanks 14 - 119 gal. CLD 23 MLTPL
Xylem Hydro Pro Water System Tanks (V Prefix) 14 - 119 gal. CLD 23 MLTPL
Xylem Hydro Pro Water System Tanks (V prefix and MP or PST suffix) 14 - 20 gal. CLD 23 MLTPL

[1] Product also complies with NSF/ANSI 372.
[G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for
    “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state
    laws and the U.S. Safe Drinking Water Act.

    

Thermal Expansion Tanks[1] [G]
Bell and Gossett (Prefix PT)[2] 14 - 86 gal. D. HOT MLTPL

[1] Product also complies with NSF/ANSI 372.
[2] Suffixes:
    blank 
    B   - Buried 
    EX  - Base extension 
    MP  - Mounted pump 
    P   - Pipe mounted 
    PST - Pump system tank
    S
[G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for
    “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state
    laws and the U.S. Safe Drinking Water Act.

    



 
A. Schulman, Inc. 
1183 Home Avenue
Akron, OH 44310 
United States 
800-873-7527 
812-253-5191
Visit this company's website


Facility : Evansville, IN

Potable Water Materials

    Water Water
    Contact Contact
Trade Designation End Use Temp Material

Potable Water Materials
Aqualoy® 125B[1] A,F C. HOT RPP
Aqualoy® 125G[1] A,F C. HOT RPP
Aqualoy® 125M Black[1] A,F C. HOT RPP
Aqualoy® 125N[1] A,F C. HOT RPP
Aqualoy® 125W[1] A,F C. HOT RPP
Aqualoy® 125W14[1] A,F C. HOT RPP
Aqualoy® 140B[1] A,F C. HOT RPP
Aqualoy® 140N[1] A,F C. HOT RPP
Aqualoy® 140W[1] A,F C. HOT RPP
Aqualoy® 145N[1] A,F C. HOT RPP
E-10025N[1] A,F C. HOT RPP
E-10026B[1] A,F C. HOT RPP

[1] Certified for a maximum surface area to volume ratio of 250 sq. in./L.



Facility : Akron, OH

Potable Water Materials

    Water Water
    Contact Contact
Trade Designation End Use Temp Material

Potable Water Materials
Aqualoy® 645N A,F C. HOT NP



Facility : Guangdong, China

Potable Water Materials

    Water Water
    Contact Contact
Trade Designation End Use Temp Material

Potable Water Materials[1]
Aqualoy® 125B A,F C. HOT RPP
Aqualoy® 125N A,F C. HOT RPP
Aqualoy® 125W A,F C. HOT RPP
Aqualoy® 140N A,F C. HOT RPP
Aqualoy® 140W A,F C. HOT RPP

[1] Certified for a maximum surface area to volume ratio of 250 sq. in./L.



 
A. W. Chesterton Co. 
860 Salem Street
Groveland, MA 01834 
United States 
978-469-6446


Facility : Groveland, MA

Mechanical Devices

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Miscellaneous Process Devices/Components [3]
1725A[1] [G] D. HOT PTFE
442 Split Mechanical Seal[G] [2] D. HOT MLTPL
442C Split Mechanical Seal[G] [2] D. HOT MLTPL
Single Non-Split Cartridge Seals[G] [2] D. HOT MLTPL

[1] Certified for use as a packing material in pumps with shaft diameters >= 0.625".
[2] Certified for mechanical seals for use with pump shafts ranging from 1" - 12" in
    diameter.  Certified for equivalent metric sizes.
[3] Only products bearing the NSF Mark on the product, product packaging, and/or
    documentation shipped with the product are Certified.
[G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for
    “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state
    laws and the U.S. Safe Drinking Water Act.

    


Protective (Barrier) Materials

    Water Water
  Water Contact Contact Contact
Trade Designation Size Restriction Temp Material

Coatings - Fittings
ARC S1 PW BLU[1] >= 12" CLD 23 EPOXY
ARC S1 PW WH[2] >= 12" CLD 23 EPOXY

[1] Colors: Blue
    Number of coats: 3
    Maximum field use dry film thickness (in mils): 45 (15 mils/coat)
    Recoat cure time and temperature: 6 hours at 77°F
    Final cure time and temperature: 7 days at 77°F
    Special Comments: Mix ratio of Part A:B is 2:1 by volume
[2] Colors: White
    Number of coats: 3
    Maximum field use dry film thickness (in mils): 45 (15 mils/coat)
    Recoat cure time and temperature: 6 hours at 77°F
    Final cure time and temperature: 7 days at 77°F
    Special Comments: Mix ratio of Part A:B is 2:1 by volume

Coatings - Pump
ARC S1 PW BLU[1] >= 4" CLD 23 EPOXY
ARC S1 PW WH[2] >= 4" CLD 23 EPOXY

[1] Colors: Blue
    Number of coats: 3
    Maximum field use dry film thickness (in mils): 45 (15 mils/coat)
    Recoat cure time and temperature: 6 hours at 77°F
    Final cure time and temperature: 7 days at 77°F
    Special Comments: Mix ratio of Part A:B is 2:1 by volume
[2] Colors: White
    Number of coats: 3
    Maximum field use dry film thickness (in mils): 45 (15 mils/coat)
    Recoat cure time and temperature: 6 hours at 77°F
    Final cure time and temperature: 7 days at 77°F
    Special Comments: Mix ratio of Part A:B is 2:1 by volume

Coatings - Valve
ARC S1 PW BLU[1] >= 4" CLD 23 EPOXY
ARC S1 PW WH[2] >= 4" CLD 23 EPOXY

[1] Colors: Blue
    Number of coats: 3
    Maximum field use dry film thickness (in mils): 45 (15 mils/coat)
    Recoat cure time and temperature: 6 hours at 77°F
    Final cure time and temperature: 7 days at 77°F
    Special Comments: Mix ratio of Part A:B is 2:1 by volume
[2] Colors: White
    Number of coats: 3
    Maximum field use dry film thickness (in mils): 45 (15 mils/coat)
    Recoat cure time and temperature: 6 hours at 77°F
    Final cure time and temperature: 7 days at 77°F
    Special Comments: Mix ratio of Part A:B is 2:1 by volume



 
A. W. Chesterton Co. 
860 Salem Street
Groveland, MA 01834 
United States 
978-469-6446
Visit this company's website


Facility : # 1 USA

Joining and Sealing Materials

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Patching Materials
ARC 5ES [1] C. HOT EPOXY

[1] The exposed surface area of each sealant in a household distribution system
    should not exceed 1.3 sq. cm/L or .2 sq. in/L.



 
A.R. Thomson Group 
3420 189th Street
Surrey, BC V32 1A7 
Canada 
604-507-6050
Visit this company's website


Facility : # 1 Canada

Joining and Sealing Materials

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Gasket/Sealing Materials
Thomson Multipac-6000 [1] C. HOT OTHER
Thomson Multipac-6000 [2] CLD 23 OTHER

[1] Certified for a maximum surface area to volume ratio of 0.3 sq. in./L when used at
    Commercial Hot (82°C) temperature.
[2] Certified for a maximum surface area to volume ratio of 0.8 sq. in./L when used at Cold
    (23°C) temperature.



 
A.R. Thomson Group 
3420 189th Street
Surrey, BC V32 1A7 
Canada 
604-507-6050
Visit this company's website


Facility : # 1 Canada

Joining and Sealing Materials

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Gasket/Sealing Materials
Thomson 4500 >= 3" CLD 23 EPDM
Thomson MultiPac 6000 [1] C. HOT OTHER
Thomson MultiPac 6000 [2] CLD 23 OTHER

[1] Certified for a maximum surface area to volume ratio of 0.3 sq. in./L when used at
    Commercial Hot (82°C) temperature.
[2] Certified for a maximum surface area to volume ratio of 0.8 sq. in./L when used at Cold
    (23°C) temperature.



 
A.U.K. Müller GmbH & Co. KG 
Dresdener Str. 162
D-40595 Düsseldorf 
Germany 
49 21 173 910
Visit this company's website


Facility : Düsseldorf, Germany

Mechanical Devices

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Valves[G]
52.009.100 3/4" C. HOT MLTPL
52.009.200 3/4" C. HOT MLTPL

[G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for
    “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state
    laws and the U.S. Safe Drinking Water Act.

    

NOTE: Only products bearing the NSF Mark on the product, product packaging, and/or
      documentation shipped with the product are Certified.

Mechanical Plumbing Devices

Trade Designation      

Valves[G]
50.005.100 Cartridge Valve      
50.005.101 Cartridge valve      
50.005.800      
50.005.801      
50.005.850      
50.007.101      
50.007.801      
50.007.806 Solenoid Cartridge Valve[1]      
50.009.101      
50.009.801      
51.005.125      
T01 50.009.800      
T02 50.009.800      

[1] Certified for models that include: 
    G 1/2 male threads 
    G 3/8 male threaded with G 3/8 female threads 
    G 3/8 male threaded with G 1/2 female threads 
    Model with sockets for customer provided fitting adapters.

[G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for
    “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state
    laws and the U.S. Safe Drinking Water Act.

    

NOTE: Only products bearing the NSF Mark on the product, product packaging, and/or
      documentation shipped with the product are Certified.

Pipes and Related Products

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Fittings [G]
CF-13 2MFC[1] 3/4" x 3/4" x 3/4" D. HOT MLTPL
CF-13 2MFO[1] 1/2" x ¾" x ¾" x ¾" D. HOT MLTPL
CF-17 2MFC[1] 3/4" C. HOT MLTPL
CF-17 2MFO[1] 3/4" C. HOT MLTPL
CF-17 3MFC[1] 3/4" C. HOT MLTPL
CF-17 3MFO[1] 3/4" C. HOT MLTPL
CF-17 C (cross piece)[1] 3/4" C. HOT MLTPL
CF-17 L (L-piece)[1] 3/4" C. HOT MLTPL
CF-17 T (T-piece)[1] 3/4" C. HOT MLTPL
CF-H G Connector 3/4"x1/8"-3/4"x1/4" C. HOT MLTPL
CF-H L 90 deg Elbow Connector 3/4" x 1/2" C. HOT MLTPL
CF-H S Straight Connector 3/4"x3/8"-3/4"x1/2" C. HOT MLTPL

[1] MFC - are models with capped outlets
    MFO - are models without capped outlets
[G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for
    “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state
    laws and the U.S. Safe Drinking Water Act.

    

NOTE: Only products bearing the NSF Mark on the product, product packaging, and/or
      documentation shipped with the product are Certified.


 
A.Y. McDonald Manufacturing 
4800 Chavenelle Road
Dubuque, IA 52001 
United States 
563-583-7311


Facility : Santa Fe Springs, CA

Pipes and Related Products

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Fittings
Copper Alloy Press-Connect Pressure Fittings 1/8" - 2 C. HOT BRASS

[1] Certified for the following configurations:
    90º Elbow Drop Ear PXF 1/2" x 3/8" - 1" x 1"
    90º Elbow Brass PXF 1/2" X 3/8" - 2" x 2"
    90º Elbow HI Ear PXF 1/2"
    Elbow Double Drop PXPXF 1/2" - 3/4"
    Union PxP 1/2" - 2"
    Union PxF 1/2" - 2"
    Union PxM 1/2" - 2"
    Vent Elbow PXPXF 1/2" x 1/2" x 1/8" - 3/4" x 3/4" x 1/8"
[G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for
    “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state
    laws and the U.S. Safe Drinking Water Act.

    


Facility : Kyunggi-Do, Republic of Korea

Pipes and Related Products

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Fittings[1] [G]
Copper Press-connect Pressure Fittings 1/2" - 4" C. HOT MLTPL

[1] Certified for the following configurations:
    90º Elbow PXP 1/2" - 4"
    90º Elbow FtgXP 1/2" - 4"
    Short Turn 90° Elbow PXP 1/2" - 4"
    Short Turn 90° Elbow FtgXP 1/2" - 4"
    45º Elbow PXP 1/2" - 4"
    45º Elbow FtgXP 1/2" - 4"
    Short Turn 45° Elbow PXP 1/2" - 4"
    Short Turn 45° Elbow FtgXP 1/2" - 4"
    Cap 1/2" - 4"
    Adapter PXF 1/2" - 4"
    Adapter PxM 1/2" - 4"
    Roll Stop Coupling PXP 1/2" - 4"
    No Stop Coupling PXP 1/2" - 4"
    With Stop Coupling 1/2" - 4"
    Reducing Coupling PXP 3/4" x 1/2" - 4" x 3"
    Reducing Coupling FtgXP 3/4" x 1/2" - 4" x 3"
    Tee PXPXP 1/2" - 4"
    Crossover PXP 1/2" - 3/4"
    Crossover FtgXP 1/2" - 3/4"
    Extended Coupling PXP 1/2" - 2"
    Adapter Ftg x F 1/2" - 2"
    Adapter Ftg x M 1/2" - 2"
    90° ELBOW P x F 1/2" - 2"
    90° ELBOW P x M 1/2" - 2"
    90° EXTENDED STREET ELBOW P x Ftg 3/4"
    TEE P x P x F 1/2" - 4"
    Adapter Flange P x Flange (4BOLT) 1/2" - 4"
    Adapter Flange P x Flange (8BOLT) 2 1/2" - 4"
    MANIFOLDS P x P 1" x 1/2" - 1" x 3/4"
[G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for
    “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state
    laws and the U.S. Safe Drinking Water Act.

    



 
A.Y. McDonald Mfg. Co. 
P.O. Box 508
Dubuque, IA 52004-0508 
United States 
563-583-7311
Visit this company's website


Facility : Zhejiang, China

Mechanical Plumbing Devices

Trade Designation      

Hot Water Dispenser Components[1] [2] [G]

72004QT 1/2 Boiler Drain Quater Turn
     

72004QT 3/4 Boiler Drain Quater Turn
     

72008QT 1/2 Boiler Drain Quater Turn Ball Valve
     

72008QT 3/4 Boiler Drain Quater Turn Ball Valve
     

[1] Product also complies to NSF/ANSI 372.
[2] This product was evaluated with 82°C water based on its end use as a hot water heater
    outlet.
[G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for
    “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state
    laws and the U.S. Safe Drinking Water Act.

    

Valves[G]

72014QT VLV QTR TN SIL 1/2" CUP
     

72014QT VLV QTR TN SIL 3/4" CUP
     

72015QT VLV QTR TURN SILCOCK 1/2"
     

72015QT VLV QTR TURN SILCOCK 3/4"
     

[G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for
    “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state
    laws and the U.S. Safe Drinking Water Act.

    



 
ABB Engineering (Shanghai) Ltd. 
No. 4528, Kangxin Highway
Pudong District, Shanghai 201319 
China 
86 216 129 8457


Facility : Warminster, PA

Mechanical Devices

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Water Meters[1]
WaterMaster FEW 40 mm - 2400 mm CLD 23 MLTPL
AquaMaster FEW 40 mm - 2400 mm CLD 23 MLTPL

[1] Only products bearing the NSF Mark on the product, product packaging, and/or
    documentation shipped with the product are Certified.



Facility : Shanghai, China

Mechanical Devices

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Water Meters[1]
AquaMaster FEW 40 mm - 2400 mm CLD 23 MLTPL
WaterMaster FEW 40 mm - 2400 mm CLD 23 MLTPL

[1] Only products bearing the NSF Mark on the product, product packaging, and/or
    documentation shipped with the product are Certified.



 
ABB Ltd. 
Oldends Lane
Stonehouse, Glos 
GL10 3TA 
United Kingdom 
44 14 5382 6661


Facility : Glos, United Kingdom

Mechanical Devices

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Water Meters
FEF[G] >= 250 mm CLD 23 MLTPL
FEP[G] 40 mm - 2400 mm CLD 23 MLTPL
FER[G] 40 mm - 600 mm CLD 23 MLTPL
FEV[G] 40 mm - 300 mm CLD 23 MLTPL
FEW[G] 40 mm - 2400 mm CLD 23 MLTPL
WaterMaster V[G] 40 mm - 300 mm CLD 23 MLTPL

[G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for
    “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state
    laws and the U.S. Safe Drinking Water Act.

    

NOTE: Only products bearing the NSF Mark on the product, product packaging, and/or
      documentation shipped with the product are Certified.


 
ABB S.p.A. 
Via Luigi Vaccani, 4
22016 Ossuccio, Como 
Italy 
39 03 445 8111
Visit this company's website


Facility : Warminster, PA

Mechanical Devices

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Transmitters/Gauges[G]
261AS - Pressure Transmitter 60 x 60 x 112 mm C. HOT MLTPL
261GS - Pressure Transmitter 60 x 60 x 112 mm C. HOT MLTPL
266DSH - Pressure Transmitter 142 x 142 x 210 mm C. HOT MLTPL
266HSH - Pressure Transmitter 142 x 91 x 215 mm C. HOT MLTPL
266NSH - Pressure Transmitter 142 x 91 x 215 mm C. HOT MLTPL

[G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for
    “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state
    laws and the U.S. Safe Drinking Water Act.

    



 
ABSFIL Co., Ltd. 
#115-9, Namyang-Ro
Gyeonggi-Do, Hwaseong-si 18281 
Korea, Republic of 
82 70 4310 5241
Visit this company's website


Facility : Chungju-Si, Republic of Korea

Mechanical Devices

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Filtration Devices/Components
PREIII-Y-Z[1] [2] [3] [4] CLD 23 PP

[1] Certification does not include inner core, adapters, o-rings, gaskets, or end caps.
[2] PRE III-Y-Z is denoted as follows:
    Y - Micron rating (um)
        0.5 - 100
    Z - Length (in)
        5 - 50
[3] Certified for use in municipal water treatment facilities.
[4] Certified for a minimum flow rate of 6840 liters per day.



 
ABZ Valves & Controls 
P.O. Box 157
Madison, KS 66860 
United States 
855-803-6786 
620-437-2440


Facility : # 1 China

Mechanical Devices

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Valves[1]
411-052 2" - 48" CLD 23 MLTPL
412-052 2" - 48" CLD 23 MLTPL
431-052 2" - 48" CLD 23 MLTPL
432-052 2" - 48" CLD 23 MLTPL
575 2" - 48" CLD 23 MLTPL
806 2" - 48" CLD 23 MLTPL
807 2" - 48" CLD 23 MLTPL
815 2" - 48" CLD 23 MLTPL
816 2" - 48" CLD 23 MLTPL

[1] Certified for equivalent metric sizes.



 
ABZ Valves & Controls 
920 Memorial City Way
Suite 1000 
Houston, TX 77024 
United States 
281-949-2500


Facility : Incheon, Republic of Korea

Mechanical Devices

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Valves [G]
Series 401/402 (Class 150) High Performance Butterfly Valve[1] 2" - 72" CLD 23 MLTPL
Series 403 (Class 150) High Performance Butterfly Valve[2] 3" - 72" CLD 23 MLTPL
Series 421/422 (Class 300) High Performance Butterfly Valve[1] 2" - 48" CLD 23 MLTPL
Series 423 (Class 300) High Performance Butterfly Valve[2] 3" - 48" CLD 23 MLTPL
Series 451/452 (Class 600) High Performance Butterfly Valve[1] 3" - 24" CLD 23 MLTPL
Series 453 (Class 600) High Performance Butterfly Valve[2] 4" - 24" CLD 23 MLTPL

[1] Certified for trims 100, 101, 102, 103, 118, 125, 126, 129, 182, and 183.
[2] Certified for trims 102, 103, 125, 126, 183.
[G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for
    “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state
    laws and the U.S. Safe Drinking Water Act.

    



 
Accella Polyurethane Systems, LLC 
2500 Adie Road
Maryland Heights, MO 63043 
United States 
770-528-9556
Visit this company's website


Facility : Cartersville, GA

Protective (Barrier) Materials

    Water Water
  Water Contact Contact Contact
Trade Designation Size Restriction Temp Material

Coatings - Tank[1] [G]
BPL 7161 >= 10,000,000 gal. CLD 23 PUA

[1] Colors: Part A: Yellow, Part B: Black, medium gray, tan,white
    Number of Coats: 1
    Maximum Field Use Dry Film Thickness (in mils): 180 (50 minimum)
    Final Cure Time and Temperature: 24 hours at 70°F
    Special Comments: Mix ratio of Part A:B is 1:1 by volume.
[G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for
    “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state
    laws and the U.S. Safe Drinking Water Act.

    



Facility : Chattanooga, TN

Joining and Sealing Materials

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Grouts
URETEK[1] [2] CLD 23 PUR
URETEK Geopolymer[1] [2] CLD 23 PUR

[1] Certified for product with the following densities and reaction speeds:
    2 pounds per cubic foot (regular speed)
    2 pounds per cubic foot (fast speed)
    3 pounds per cubic foot (regular speed)
    3 pounds per cubic foot (fast speed)
    4 pounds per cubic foot (regular speed)
    4 pounds per cubic foot (fast speed)
    5 pounds per cubic foot (regular speed)
    5 pounds per cubic foot (fast speed)
    8 pounds per cubic foot (regular speed)
    8 pounds per cubic foot (fast speed)
    
    Mix ratio is 1:1 (A:B) by volume or 8.1:6.9 (A:B) by weight.
    Minimum cure time is 60 minutes at ambient temperatures.
[2] Certified for a maximum surface area to volume ratio of 0.375 square inches per liter.



 
Accent Control Systems 
2101 Potshop Lane
Norristown, PA 19403 
United States 
610-630-7640


Facility : Ningbo, China

Mechanical Devices

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Water Meters[G]
GLF-062/GLF-062-R 5/8" x 1/2" CLD 23 MLTPL
GLF-075/GLF-075-R 5/8" x 3/4" CLD 23 MLTPL
GLF-100/GLF-100-R 3/4" x 1" CLD 23 MLTPL
GLF-100F/GLF-100F-R 1" CLD 23 MLTPL
GLF-150/GLF-150-R 1 1/2" CLD 23 MLTPL
GLF-200(F)/GLF-200-R(F) 2" CLD 23 MLTPL
GLF-200/GLF-200-R 2" CLD 23 MLTPL

[G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for
    “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state
    laws and the U.S. Safe Drinking Water Act.

    



 
Access-Able Technologies, Inc. 
1275 Bennett Drive #115
Longwood, FL 32750 
United States 
800-572-4894 
407-834-2999


Facility : # 1 USA

Joining and Sealing Materials

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Patching Materials [G]
Pow-R Stick Steel Hard Epoxy Putty (Copper Color) [1] [2] C. HOT EPOXY
Pow-R Stick Steel Hard Epoxy Putty (Grey Color) [1] [2] C. HOT EPOXY
Pow-R Stick Steel Hard Epoxy Putty (White Color) [1] [2] C. HOT EPOXY
STIC-O-STEEL POW-R Putty [1] [2] C. HOT EPOXY

[1] Certified for a maximum surface area to volume ratio of 0.3 sq. in./L in pipe or 1% of a
    20,000 gallon tank.
[2] To obtain the proper mix, use at least a 3/4" length, but no more than 1/3 of a full
    stick, of product which has been cut with a knife. Product must be mixed for 60-90
    seconds.
[G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for
    “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state
    laws and the U.S. Safe Drinking Water Act.

    



 
Accimin SA de CV 
Lafayette No. 121. Col. Anzures
Mexico City 11590 
México 
52 55 11010920
Visit this company's website


Facility : Tlalnepantla, Mexico

Process Media

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Filtration Media[1]
Dicamex 4107 31.06 µm CLD 23 PERL
Dicamex 4127 42.29 µm CLD 23 PERL
Dicamex 4147 44.76 µm CLD 23 PERL
Dicamex 4157 37.26 µm CLD 23 PERL
Dicamex 417 14 µm CLD 23 PERL
Dicamex 4187 45.38 µm CLD 23 PERL
Dicamex 4217 50.37 µm CLD 23 PERL
Dicamex 427 15.44 µm CLD 23 PERL
Dicamex 4337 53.37 µm CLD 23 PERL
Dicamex 437 29.77 µm CLD 23 PERL
Dicamex 447 28.6 µm CLD 23 PERL
Dicamex 477 29.37 µm CLD 23 PERL
Dicamex CP 150 34.57 µm CLD 23 PERL
Dimesa 4187 45.38 µm CLD 23 PERL
Dimesa 4337 58.65 µm CLD 23 PERL

[1] Certified for a  maximum use level of 1,200 mg/L.

NOTE: Certified for water treatment plant applications.
      This product has not been evaluated for point of use applications.


 
Accor Technology Inc. 
1400 - 112th Avenue South East
Suite 100 
Bellevue, WA 98004 
United States 
800-447-5848 
509-662-0608


Facility : East Wenatchee, WA

Mechanical Plumbing Devices

Trade Designation      

Connector Hoses

Riser Assemblies[1]
R-5CP(1)-7(2)      
R-5CS(1)-7(2)      
R-5LP(1)-5(2)      
R-5LS(1)-5(2)      
R-CP(1)-7(2)      
R-CS(1)-7(2)      
R-LP(1)-3(2)      
R-LP(1)-5(2)      
R-LS(1)-3(2)      
R-LS(1)-5(2)      
R2-IP(1)-2(2)      
R3-LP(1)-3(2)      
RCP45T12-7(2)      

[1] (1) Hose length
    (2) Packaging options (M, F, E, EL, CF, CM, PF, FM, XM, XF, XE, XL, XC, or R)

Supply Stops

Coupling w/ attached riser[1]
PR30-LP(1)-3(2)      
PR30-SP(1)-3(2)      
PR50-CP(1)-7(2)      
PR50-CS(1)-7(2)      
PR50-LP(1)-3(2)      
PR50-LP(1)-5(2)      
PR50-LS(1)-3(2)      
PR50-LS(1)-5(2)      
PR50-P(1)-RK(2)      
PR50-S(1)-RK(2)      
PR50-SP(1)-5(2)      

[1] (1) Hose length
    (2) Packaging options (M, F, E, EL, CF, CM, PF, FM, XM, XF, XE, XL, XC, or R)

Valve or Coupling[1]
PC5-3(2)      
PC5S-3(2)      
PE5-3(2)      
PE5S-3(2)      
PO5-2(2)      
PO5-3(2)      
PO5-75(2)      
PO5-CAP(2)      
PR-30(2)      
PR-50(2)      
TH5-3(2)      

[1] (1) Hose length
    (2) Packaging options (M, F, E, EL, CF, CM, PF, FM, XM, XF, XE, XL, XC, or R)

Valve w/ attached riser[1]
PC5-CP(1)-7(2)      
PC5-CS(1)-7(2)      
PC5-LP(1)-5(2)      
PC5-LS(1)-5(2)      
PE5-CP(1)-7(2)      
PE5-CS(1)-7(2)      
PE5-LP(1)-5(2)      
PE5-LS(1)-5(2)      
PO5-CP(1)-7(2)      
PO5-CS(1)-7(2)      
PO5-IP(1)-2(2)      
PO5-LP(1)-3(2)      
PO5-LP(1)-5(2)      
PO5-LP4T15-5(2)      
PO5-LS(1)-3(2)      
PO5-LS(1)-5(2)      
PO5-LS4T15-5(2)      
PO5-P(1)-RK(2)      
PO5-P-PR30(2)      
PO5-S(1)-RK(2)      
PO5-S-PR30(2)      
PO5P10T10RK(2)      

[1] (1) Hose length
    (2) Packaging options (M, F, E, EL, CF, CM, PF, FM, XM, XF, XE, XL, XC, or R)



 
ACCOR Technology, Inc. 
608 State Street South
Suite 100 
Kirkland, WA 98033 
United States 
877-647-5870 
425-284-3320
Visit this company's website


Facility : East Wenatchee, WA

Pipes and Related Products

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Fittings [G]
PF50C XE[2] 1/2" C. HOT MLTPL
PF50E XE[2] 1/2" C. HOT MLTPL
PF50MT XE[1] 1/2" C. HOT MLTPL
PF50T XE[2] 1/2" C. HOT MLTPL
PF75C XE[2] 3/4" C. HOT MLTPL
PF75E XE[2] 3/4" C. HOT MLTPL
PF75T XE[2] 3/4" C. HOT MLTPL

[1] PF50MT XE – 1/2" PushOnManifold Tee Code: 
    P  – PushOn 
    F  – Fitting 
    50 – 1/2 inch 
    M  – Manifold 
    T  – Tee 
    X  – Compatible with PEX pipe (as well as copper and CPVC). 
    E  – Bulk packaged (each)
[2] Configuration code breakdown: 
    P  – PushOn 
    F  – Fitting 
    50 - 1/2" 
    75 - 3/4" 
    M  – Manifold 
    T  – Tee 
    C  – Coupling 
    E  – Elbow 
    X  – Compatible with PEX pipe (as well as copper and CPVC) 
    E  – Bulk packaged (each)
[G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for
    “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state
    laws and the U.S. Safe Drinking Water Act.

    



 
ACCUCAST Ltd. 
415 South 21ST Street
Waco, TX 76706 
United States 
254-756-3200
Visit this company's website


Facility : Shanxi, China

Pipes and Related Products

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Fittings[1] [G]
Ductile Iron C110 Flanged Pipe Fittings 3" - 12" CLD 23 ASPH
Ductile Iron C153 Mechanical Joint Pipe Fittings 3" - 12" CLD 23 ASPH

[1] Certification does not include gaskets.
[G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for
    “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state
    laws and the U.S. Safe Drinking Water Act.

    



 
Accuflex Industrial Hose Ltd. 
760 Imperial Road North
Guelph, ON N1K 1Z3 
Canada 
519-836-5460
Visit this company's website


Facility : Guelph, Ontario, Canada

Pipes and Related Products

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Tubing/Hose [G]
Bev-Flex® 172 1/4" - 1" CLD 23 PE
Bev-Seal® 176 1/4" - 1" CLD 23 PE
Bev-Seal® 228 1/4" - 1" CLD 23 PE
Bev-Seal® Ultra 175 3/16" - 1" CLD 23 PET
Bev-Seal® Ultra 235 3/16" - 1" CLD 23 PET
Bevlex® 170 1/4" - 1" CLD 23 PE
Bevlex® 174 1/4" - 1" CLD 23 PE
Bevlex® 222 1/4" - 1" CLD 23 PE
Bevlex® 222YYY[1] 1/4" - 1" CLD 23 PE
Bevlex® 224 1/4" - 1" CLD 23 PE
Bevlex® Plus 180 3/16" - 1" CLD 23 PET
Kuri Tec® A3236 1/4" - 1" CLD 23 PE
Kuri Tec® A3246 1/4" - 1" CLD 23 PE

[1] YYY denotes color for the outermost layer. Color codes are:
    BLK  - Black
    BLU  - Blue
    DGRY - Dark Gray
    GRN  - Green
    LGRY - Light Gray 
    RED  - Red
    WHT  - White
[G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for
    “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state
    laws and the U.S. Safe Drinking Water Act.

    



 
Ace Hardware Corporation 
2200 Kensington Ct
Oakbrook, IL 60523 
United States 
630-990-8686
Visit this company's website


Facility : Omaha, NE

Joining and Sealing Materials

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Sealants
Ace Pipe Thread Compound >= 1/2" C. HOT SLT
Ace TFE Paste White >= 1/2" C. HOT SLT



 
Ace Roto-Mold 
Division of Den Hartog Industries Inc.
4010 Hospers Drive South 
P.O. Box 425 
Hospers, IA 51238-0425 
United States 
800-342-3408 
712-752-8432
Visit this company's website


Facility : Hospers, IA

Protective (Barrier) Materials

    Water Water
  Water Contact Contact Contact
Trade Designation Size Restriction Temp Material

Tanks
ACT1000-LP Cistern Tank[1] 1000 gal. CLD 23 MLTPL
ACT1500-LP Cistern Tank[1] 1500 gal. CLD 23 MLTPL
ACT2000-LP Cistern Tank[1] 2000 gal. CLD 23 MLTPL
ACT2500-LP Cistern Tank[1] 2500 gal. CLD 23 MLTPL
ARM-10115 Stock Tank[1] 50 gal. CLD 23 MLTPL
ARM-10116 Stock Tank[1] 100 gal. CLD 23 MLTPL
ARM-10117 Stock Tank[1] 150 gal. CLD 23 MLTPL
ARM-10135 Stock Tank[1] 920 gal. CLD 23 MLTPL
ARM-10138 Stock Tank[1] 320 gal. CLD 23 MLTPL
ARM-10139 Stock Tank[1] 610 gal. CLD 23 MLTPL
ARM-19455 Stock Tank[1] 120 gal. CLD 23 MLTPL
CB00150-36 Cone Bottom Tank[1] 150 gal. CLD 23 MLTPL
CB00200-42 Cone Bottom Tank[1] 200 gal. CLD 23 MLTPL
CB00300-42 Cone Bottom Tank[1] 300 gal. CLD 23 MLTPL
CB00325-52 Cone Bottom Tank[1] 345 gal. CLD 23 MLTPL
CB00350-42 Cone Bottom Tank[1] 350 gal. CLD 23 MLTPL
CB00500-52 Cone Bottom Tank[1] 500 gal. CLD 23 MLTPL
CB0055-23 Batch Tank - Cone Bottom[1] 55 gal. CLD 23 MLTPL
CB00800-86 Cone Bottom Tank[1] 800 gal. CLD 23 MLTPL
CB0100-23 Batch Tank - Cone Bottom[1] 100 gal. CLD 23 MLTPL
CB0145-36 Batch Tank - Cone Bottom[1] 145 gal. CLD 23 MLTPL
CB0200-36 Batch Tank - Cone Bottom[1] 200 gal. CLD 23 MLTPL
CB0250-36 Batch Tank - Cone Bottom[1] 250 gal. CLD 23 MLTPL
CB0325-36 Batch Tank - Cone Bottom[1] 325 gal. CLD 23 MLTPL
CB1000-64 Cone Bottom Tank[1] 1000 gal. CLD 23 MLTPL
CB1000-90 Cone Bottom Tank[1] 1000 gal. CLD 23 MLTPL
CB1005-64 Conebottom Tank[1] 1005 gal. CLD 23 MLTPL
CB1005-90 Cone Bottom Tank[1] 1005 gal. CLD 23 MLTPL
CB1150-90 Cone Bottom-Industrial Top[1] 1150 gal. CLD 23 MLTPL
CB1200-90 Cone Bottom Tank[1] 1200 gal. CLD 23 MLTPL
CB1300-90 Cone Bottom Tank[1] 1300 gal. CLD 23 MLTPL
CB1490-64 Cone Bottom Tank[1] 1490 gal. CLD 23 MLTPL
CB1500-64 Cone Bottom Tank [1] 1500 gal. CLD 23 MLTPL
CB1500-64 Conebottom Tank[1] 1500 gal. CLD 23 MLTPL
CB1600-90 Cone Bottom Tank[1] 1600 gal. CLD 23 MLTPL
CB1700-86 Cone Bottom Tank[1] 1700 gal. CLD 23 MLTPL
CB2495-90 Cone Bottom Tank [1] 2495 gal. CLD 23 MLTPL
CB2495-90 Cone Bottom-Industrial Top[1] 2495 gal. CLD 23 MLTPL
CB2500-90 Cone Bottom Tank[1] 2500 gal. CLD 23 MLTPL
CB2600-86 Cone Bottom Tank[1] 2600 gal. CLD 23 MLTPL
CB2600-90 Cone Bottom Tank[1] 2600 gal. CLD 23 MLTPL
CB3000-90 Cone Bottom Tank[1] 3000 gal. CLD 23 MLTPL
CB3000-96 Cone Bottom Tank[1] 3000 gal. CLD 23 MLTPL
CB4200-122 Cone Bottom Tank [1] 4200 gal. CLD 23 MLTPL
CB4600-102 Cone Bottom Tank[1] 4600 gal. CLD 23 MLTPL
CB4900-102 Cone Bottom Tank[1] 4900 gal. CLD 23 MLTPL
CB6000-122 Cone Bottom Tank [1] 6000 gal. CLD 23 MLTPL
CB6900-102 Cone Bottom Tank[1] 6900 gal. CLD 23 MLTPL
CB8250-122 Cone Bottom Tank[1] 8250 gal. CLD 23 MLTPL
DW0065-28 Double Wall Vertical Tank[2] [4] 65 gal. CLD 23 MLTPL
DW0120-36 Double Wall Vertical Tank[2] [4] 120 gal. CLD 23 MLTPL
DW0150-36 Double Wall Vertical Tank[2] [4] 150 gal. CLD 23 MLTPL
DW0300-57 Double Wall Vertical Tank[2] [4] 300 gal. CLD 23 MLTPL
DW0500-57 Double Wall Vertical Tank[2] [4] 500 gal. CLD 23 MLTPL
DW1000-77 Double Wall Vertical Tank[2] [4] 1000 gal. CLD 23 MLTPL
DW1500-77 Double Wall Vertical Tank[2] [4] 1500 gal. CLD 23 MLTPL
DW2000-102 Double Wall Vertical Tank[2] [4] 2000 gal. CLD 23 MLTPL
DW2500-120 Double Wall Vertical Tank[2] [4] 2500 gal. CLD 23 MLTPL
DW6000-120 Double Wall Vertical Tank[2] [4] 6000 gal. CLD 23 MLTPL
DW6500-120 Double Wall Vertical Tank[2] [4] 6500 gal. CLD 23 MLTPL
FM0015-14S Leg Tank[1] 15 gal. CLD 23 MLTPL
FM0025-16S Leg Tank[1] 25 gal. CLD 23 MLTPL
FM00925-DS Leg Tank[1] 925 gal. CLD 23 MLTPL
FM01065-56 Leg Tank[1] 1065 gal. CLD 23 MLTPL
FM01300-DS Leg Tank[1] 1300 gal. CLD 23 MLTPL
FM1010-48 Leg Tank [1] 1010 gal. CLD 23 MLTPL
FM1610-78S Leg Tank[1] 1610 gal. CLD 23 MLTPL
FM1750-62S Leg Tank[1] 1750 gal. CLD 23 MLTPL
FM1800-2S Leg Tank[1] 1800 gal. CLD 23 MLTPL
FM2350-2S Leg Tank[1] 2350 gal. CLD 23 MLTPL
FM2600-2S Leg Tank[1] 2600 gal. CLD 23 MLTPL
FM2750-88 Leg Tank[1] 2750 gal. CLD 23 MLTPL
FM3250-88 Leg Tank [1] 3250 gal. CLD 23 MLTPL
FM4200-92 Leg Tank[1] 4200 gal. CLD 23 MLTPL
FM4250-88 Leg Tank [1] 4250 gal. CLD 23 MLTPL
FM4250-92 Leg Tank [1] 4250 gal. CLD 23 MLTPL
FS00125-35 Leg Tank[1] 125 gal. CLD 23 MLTPL
FS00165-32 Leg Tank[1] 165 gal. CLD 23 MLTPL
FS00225-38 Leg Tank[1] 225 gal. CLD 23 MLTPL
FS00325-38 Leg Tank[1] 325 gal. CLD 23 MLTPL
FS00335-44 Leg Tank[1] 335 gal. CLD 23 MLTPL
FS0035-18 Leg Tank[1] 35 gal. CLD 23 MLTPL
FS00510-57 Leg Tank[1] 510 gal. CLD 23 MLTPL
FS00535-48 Leg Tank[1] 535 gal. CLD 23 MLTPL
FS0055-23 Leg Tank[1] 55 gal. CLD 23 MLTPL
FS0065-24 Leg Tank[1] 65 gal. CLD 23 MLTPL
FS0070-24 Leg Tank[1] 70 gal. CLD 23 MLTPL
FS00735-48 Leg Tank[1] 735 gal. CLD 23 MLTPL
FS00925-DW Leg Tank[1] 925 gal. CLD 23 MLTPL
FS01005-48 Leg Tank[1] 1005 gal. CLD 23 MLTPL
FS01010-48 Leg Tank[1] 1010 gal. CLD 23 MLTPL
FS01035-78 Leg Tank[1] 1035 gal. CLD 23 MLTPL
FS01065-56W Leg Tank[1] 1065 gal. CLD 23 MLTPL
FS01300-DW Leg Tank[1] 1300 gal. CLD 23 MLTPL
FS01600 Sectional Tank[1] 1600 gal. CLD 23 MLTPL
FS01610 Flat Bottom Leg Tank[1] 1610 gal. CLD 23 MLTPL
FS1750-62W Leg Tank[1] 1750 gal. CLD 23 MLTPL
FS1800-2W Leg Tank[1] 1800 gal. CLD 23 MLTPL
FS2350-88 Leg Tank[1] 2350 gal. CLD 23 MLTPL
FS2600-2W Leg Tank[1] 2600 gal. CLD 23 MLTPL
FS2750-88 Leg Tank[1] 2750 gal. CLD 23 MLTPL
FS3200-2S Leg Tank[1] 3200 gal. CLD 23 MLTPL
FS3250-88 Leg Tank[1] 3250 gal. CLD 23 MLTPL
FS4200-92 Leg Tank[1] 4200 gal. CLD 23 MLTPL
FS4250-92 Leg Tank [1] 4250 gal. CLD 23 MLTPL
GV07000-142 Vertical Tank 7000 gal. CLD 23 PE
GV1050-86 Gusseted Top Tank[1] 1050 gal. CLD 23 MLTPL
GV10500-142 Vertical Tank 10500 gal. CLD 23 PE
GV1250-142 Vertical Tank 12500 gal. CLD 23 PE
GV1350-86 Gusseted Top Tank[1] 1350 gal. CLD 23 MLTPL
GV1500-86 Gusseted Top Tank[1] 1500 gal. CLD 23 MLTPL
GV15500-142 Vertical Tank 15500 gal. CLD 23 PE
GV1650-86 Gusseted Top Tank[1] 1650 gal. CLD 23 MLTPL
HE0085-36 Elliptical Tank [1] 85 gal. CLD 23 MLTPL
HE0200-41 Elliptical Tank[1] 200 gal. CLD 23 MLTPL
HE0300-48 Elliptical Tank[1] 300 gal. CLD 23 MLTPL
HE0400-57 Elliptical Tank[1] 400 gal. CLD 23 MLTPL
HE0500-57 Elliptical Tank[1] 500 gal. CLD 23 MLTPL
HE0600-64 Elliptical Tank [1] 600 gal. CLD 23 MLTPL
HE0750-69 Elliptical Tank[1] 750 gal. CLD 23 MLTPL
HE0850-69 Elliptical Tank[1] 850 gal. CLD 23 MLTPL
HE1000-78 Elliptical Tank[1] 1000 gal. CLD 23 MLTPL
HE1250-78 Elliptical Tank[1] 1250 gal. CLD 23 MLTPL
HE1600-78 Elliptical Tank[1] 1600 gal. CLD 23 MLTPL
HED0500-57 Elliptical Tank[1] 500 gal. CLD 23 MLTPL
HED0750-69 Elliptical Tank[1] 750 gal. CLD 23 MLTPL
HED0850-69 Elliptical Tank[1] 850 gal. CLD 23 MLTPL
HED1000-78 Elliptical Tank[1] 1000 gal. CLD 23 MLTPL
HED1250-78 Elliptical Tank[1] 1250 gal. CLD 23 MLTPL
HED1600-78 Elliptical Tank[1] 1600 gal. CLD 23 MLTPL
HZ00100 Horizontal Tank[1] 100 gal. CLD 23 MLTPL
HZ0025-23 Horizontal Tank[1] 25 gal. CLD 23 MLTPL
HZ0055-23 Horizontal Tank[1] 55 gal. CLD 23 MLTPL
HZ0075-24 Horizontal Tank[1] 75 gal. CLD 23 MLTPL
HZ0095-24 Horizontal Tank[1] 95 gal. CLD 23 MLTPL
HZ0110-30 Horizontal Tank[1] 110 gal. CLD 23 MLTPL
HZ0150-30 Horizontal Tank[1] 150 gal. CLD 23 MLTPL
HZ0150-32 Horizontal Tank[1] 150 gal. CLD 23 MLTPL
HZ0200-32 Horizontal Tank[1] 200 gal. CLD 23 MLTPL
HZ0200-38 Horizontal Tank[1] 200 gal. CLD 23 MLTPL
HZ0300-38 Horizontal Tank[1] 300 gal. CLD 23 MLTPL
HZ0500-48 Horizontal Tank[1] 500 gal. CLD 23 MLTPL
IN0015-19 Inductor Tank[1] 15 gal. CLD 23 MLTPL
IN0015-19SM Inductor Tank[1] 15 gal. CLD 23 MLTPL
IN0030-24 Inductor Tank[1] 30 gal. CLD 23 MLTPL
IN0040-30 Inductor Tank[1] 40 gal. CLD 23 MLTPL
IN0055-24 Inductor Tank [1] 55 gal. CLD 23 MLTPL
IN0060-24 Inductor Tank[1] 60 gal. CLD 23 MLTPL
IN0085-30 Inductor Tank[1] 85 gal. CLD 23 MLTPL
IN0110-30 Inductor Tank[1] 110 gal. CLD 23 MLTPL
INFD07-15 Inductor Tank [1] 7 gal. CLD 23 MLTPL
INFD085 Full Drain Inductor[1] 85 gal. CLD 23 MLTPL
INFD10-15 Inductor Tank [1] 10 gal. CLD 23 MLTPL
INFD110-30 Inductor Tank[1] 110 gal. CLD 23 MLTPL
INFD15-19 Inductor Tank[1] 15 gal. CLD 23 MLTPL
INFD30-24 Inductor Tank[1] 30 gal. CLD 23 MLTPL
INFD60-24 Inductor Tank[1] 60 gal. CLD 23 MLTPL
INFD60-30 Inductor Tank[1] 60 gal. CLD 23 MLTPL
LP0068-RT Low Profile Tank[1] 68 gal. CLD 23 MLTPL
OC0055-23 Batch Tank- Cone Bottom-Open Top[1] 55 gal. CLD 23 MLTPL
OC0100-23 Batch Tank- Cone Bottom-Open Top[1] 100 gal. CLD 23 MLTPL
OC0145-36 Batch Tank- Cone Bottom-Open Top[1] 145 gal. CLD 23 MLTPL
OC0200-36 Batch Tank- Cone Bottom-Open Top[1] 200 gal. CLD 23 MLTPL
OC0250-36 Batch Tank- Cone Bottom-Open Top[1] 250 gal. CLD 23 MLTPL
OC0325-36 Batch Tank- Cone Bottom-Open Top[1] 325 gal. CLD 23 MLTPL
OP0055-23 Batch Tank- Vertical- Open Top[1] 55 gal. CLD 23 MLTPL
OP0100-23 Batch Tank- Vertical- Open Top[1] 100 gal. CLD 23 MLTPL
OP0145-36 Batch Tank- Vertical- Open Top[1] 145 gal. CLD 23 MLTPL
OP0200-36 Batch Tank- Vertical- Open Top[1] 200 gal. CLD 23 MLTPL
OP0210-40 Open Top[1] 210 gal. CLD 23 MLTPL
OP0250-36 Batch Tank- Vertical- Open Top[1] 250 gal. CLD 23 MLTPL
OP0325-36 Batch Tank- Vertical- Open Top[1] 325 gal. CLD 23 MLTPL
PCO035-16W PCO Tank[1] 35 gal. CLD 23 MLTPL
PCO050-19S PCO Tank[1] 50 gal. CLD 23 MLTPL
PCO050-19W PCO Tank[1] 50 gal. CLD 23 MLTPL
PCO100-30S PCO Tank[1] 100 gal. CLD 23 MLTPL
PCO100-30W PCO Tank[1] 100 gal. CLD 23 MLTPL
PCO150-37S PCO Tank[1] 150 gal. CLD 23 MLTPL
PCO150-37W PCO Tank[1] 150 gal. CLD 23 MLTPL
PCO200-37S PCO Tank[1] 200 gal. CLD 23 MLTPL
PCO200-37W PCO Tank[1] 200 gal. CLD 23 MLTPL
PCO300-37S PCO Tank[1] 300 gal. CLD 23 MLTPL
PCO300-37W PCO Tank[1] 300 gal. CLD 23 MLTPL
PU0200-52 Pickup Tank[1] 200 gal. CLD 23 MLTPL
PU0205-52 Pickup Tank[1] 205 gal. CLD 23 MLTPL
PU0305-60 Pickup Tank[1] 305 gal. CLD 23 MLTPL
PU0350-62 Pickup Tank[1] 350 gal. CLD 23 MLTPL
PU0450-62 Pickup Tank[1] 450 gal. CLD 23 MLTPL
SP-0012RT Applicator Tank[1] 12 gal. CLD 23 MLTPL
SP-0012VM Applicator Tank[1] 12 gal. CLD 23 MLTPL
SP-0019-VM Applicator Tank[1] 19 gal. CLD 23 MLTPL
SP-0020-LC Applicator Tank[1] 20 gal. CLD 23 MLTPL
SP0003-RT Specialty Tank[1] 3 gal. CLD 23 MLTPL
SP0004-SQ5 Specialty Tank[1] 4 gal. CLD 23 MLTPL
SP0004-SQ8 Specialty Tank[1] 4 gal. CLD 23 MLTPL
SP0005-RT Rectangle Tank[1] 5 gal. CLD 23 MLTPL
SP0005-SQ5 Specialty Tank[1] 5 gal. CLD 23 MLTPL
SP0005-SQ8 Specialty Tank[1] 5 gal. CLD 23 MLTPL
SP0006-2N Rectangle Tank[1] 6 gal. CLD 23 MLTPL
SP0006-2P Rectangle Tank[1] 6 gal. CLD 23 MLTPL
SP0007-RT Rectangle Tank[1] 7 gal. CLD 23 MLTPL
SP0008-VM Applicator Tank[1] 8 gal. CLD 23 MLTPL
SP0010-SQ8 Specialty Tank[1] 10 gal. CLD 23 MLTPL
SP0015-SQ Specialty Tank [1] 15 gal. CLD 23 MLTPL
SP0016-MM Rectangle Tank[1] 16 gal. CLD 23 MLTPL
SP002.5-RT Specialty Tank[1] 2.5 gal. CLD 23 MLTPL
SP0020-OM Rectangle Tank[1] 20 gal. CLD 23 MLTPL
SP0026-RT Utility Tank[1] 26 gal. CLD 23 MLTPL
SP003.5-CL Specialty Tank[1] 3.5 gal. CLD 23 MLTPL
SP0035-RT Total Drain Rectangular Tank[1] 35 gal. CLD 23 MLTPL
SP0045-AS Utility Tank[1] 45 gal. CLD 23 MLTPL
SP0050-RT Utility Tank[1] 50 gal. CLD 23 MLTPL
SP0055-MM Utility Tank[1] 55 gal. CLD 23 MLTPL
SP0056-RT Total Drain Rectangular Tank[1] 56 gal. CLD 23 MLTPL
SP0080-RT Utility Tank[1] 80 gal. CLD 23 MLTPL
SP0100-RT Utility Tank[1] 100 gal. CLD 23 MLTPL
SP01000-UT Utility Tank[1] 1000 gal. CLD 23 MLTPL
SP0150-RT Utility Tank[1] 150 gal. CLD 23 MLTPL
SP0200-RT Utility Tank[1] 200 gal. CLD 23 MLTPL
SP0250-UT Utility Tank[1] 250 gal. CLD 23 MLTPL
SP0300-UT Utility Tank[1] 300 gal. CLD 23 MLTPL
SP0400-UT Utility Tank[1] 400 gal. CLD 23 MLTPL
SP0500-UT Utility Tank[1] 500 gal. CLD 23 MLTPL
SP0750-UT Utility Tank[1] 750 gal. CLD 23 MLTPL
SSPU0200-70 Pickup Tank [1] 200 gal. CLD 23 MLTPL
SSPU0300-70 Pickup Tank [1] 300 gal. CLD 23 MLTPL
SSPU0400-70 Pickup Tank [1] 400 gal. CLD 23 MLTPL
VT0010-12 Vertical Polyethylene Storage Tank[2] [3] 10 gal. CLD 23 PE
VT0020-16 Vertical Polyethylene Storage Tank[2] [3] 20 gal. CLD 23 PE
VT0025-18 Vertical Polyethylene Storage Tank[2] [3] 25 gal. CLD 23 PE
VT0040-18 Vertical Polyethylene Storage Tank[2] [3] 40 gal. CLD 23 PE
VT0055-20 Vertical Polyethylene Storage Tank[2] [3] 55 gal. CLD 23 PE
VT0055-23 Batch Tank- Vertical[1] 55 gal. CLD 23 MLTPL
VT0065-23 Vertical Polyethylene Storage Tank[2] [3] 65 gal. CLD 23 PE
VT0075-23 Vertical Polyethylene Storage Tank[2] [3] 75 gal. CLD 23 PE
VT0100-23 Batch Tank- Vertical[1] 100 gal. CLD 23 MLTPL
VT0100-28 Vertical Polyethylene Storage Tank[2] [3] 100 gal. CLD 23 PE
VT0105-23 Vertical Polyethylene Storage Tank[2] [3] 100 gal. CLD 23 PE
VT0110-32 Vertical Polyethylene Storage Tank[2] [3] 110 gal. CLD 23 PE
VT0130-32 Vertical Polyethylene Storage Tank[2] [3] 130 gal. CLD 23 PE
VT0135-28 Vertical Polyethylene Storage Tank[2] [3] 135 gal. CLD 23 PE
VT0145-36 Batch Tank- Vertical[1] 145 gal. CLD 23 MLTPL
VT0160-28 Vertical Polyethylene Storage Tank[2] [3] 160 gal. CLD 23 PE
VT0175-31 Vertical Polyethylene Storage Tank[2] [3] 160 gal. CLD 23 PE
VT0180-40 Vertical Polyethylene Storage Tank[2] [3] 180 gal. CLD 23 PE
VT0200-36 Batch Tank- Vertical[1] 200 gal. CLD 23 MLTPL
VT0210-40 Vertical Polyethylene Storage Tank[2] [3] 210 gal. CLD 23 PE
VT0225-31 Vertical Polyethylene Storage Tank[2] [3] 225 gal. CLD 23 PE
VT0250-36 Batch Tank- Vertical[1] 250 gal. CLD 23 MLTPL
VT0265-31 Vertical Polyethylene Storage Tank[2] [3] 265 gal. CLD 23 PE
VT0295-42 Vertical Polyethylene Storage Tank[2] [3] 2635 gal. CLD 23 PE
VT0300-35 Vertical Polyethylene Storage Tank[2] [3] 300 gal. CLD 23 PE
VT0300-42 Vertical Polyethylene Storage Tank[2] [3] 300 gal. CLD 23 PE
VT0325-36 Batch Tank- Vertical[1] 325 gal. CLD 23 MLTPL
VT0405-52 Vertical Polyethylene Storage Tank[2] [3] 405 gal. CLD 23 PE
VT0420-42 Vertical Polyethylene Storage Tank[2] [3] 420 gal. CLD 23 PE
VT0425-42 Vertical Polyethylene Storage Tank[2] [3] 425 gal. CLD 23 PE
VT0500-52 Vertical Polyethylene Storage Tank[2] [3] 500 gal. CLD 23 PE
VT0505-46 Vertical Polyethylene Storage Tank[2] [3] 505 gal. CLD 23 PE
VT0550-52 Vertical Polyethylene Storage Tank[2] [3] 550 gal. CLD 23 PE
VT0600-46 Vertical Polyethylene Storage Tank[2] [3] 600 gal. CLD 23 PE
VT0625-64 Vertical Polyethylene Storage Tank[2] [3] 625 gal. CLD 23 PE
VT0800-46 Vertical Polyethylene Storage Tank[2] [3] 800 gal. CLD 23 PE
VT0850-54 Vertical Polyethylene Storage Tank[2] [3] 850 gal. CLD 23 PE
VT0900-46 Vertical Polyethylene Storage Tank[2] [3] 900 gal. CLD 23 PE
VT1000-64 Vertical Polyethylene Storage Tank[2] [3] 1000 gal. CLD 23 PE
VT1050-86 Vertical Polyethylene Storage Tank[2] [3] 1050 gal. CLD 23 PE
VT10500-142 Vertical Tank [1] 10500 gal. CLD 23 MLTPL
VT10500-2500 Vertical Polyethylene Storage Tank[2] [3] 10,500 gal. CLD 23 PE
VT10500-2800 Vertical Polyethylene Storage Tank[2] [3] 10,500 gal. CLD 23 PE
VT1200-64 Vertical Polyethylene Storage Tank[2] [3] 1200 gal. CLD 23 PE
VT12500-142 Vertical Tank [1] 12500 gal. CLD 23 MLTPL
VT12500-142 Vertical Polyethylene Storage Tank[2] [3] 12,500 gal. CLD 23 PE
VT1350-86 Vertical Polyethylene Storage Tank[2] [3] 1350 gal. CLD 23 PE
VT1500-64 Vertical Polyethylene Storage Tank[2] [3] 1500 gal. CLD 23 PE
VT1500-86 Vertical Polyethylene Storage Tank[2] [3] 1500 gal. CLD 23 PE
VT1525-64 Vertical Polyethylene Storage Tank[2] [3] 1525 gal. CLD 23 PE
VT15500-142 Vertical Tank [1] 15500 gal. CLD 23 MLTPL
VT1650-86 Vertical Polyethylene Storage Tank[2] [3] 1650 gal. CLD 23 PE
VT2000-64 Vertical Polyethylene Storage Tank[2] [3] 2000 gal. CLD 23 PE
VT2000-90 Vertical Polyethylene Storage Tank[2] [3] 2000 gal. CLD 23 PE
VT2050-86 Vertical Polyethylene Storage Tank[2] [3] 2050 gal. CLD 23 PE
VT2150-102 Vertical Polyethylene Storage Tank[2] [3] 2150 gal. CLD 23 PE
VT2500-90 Vertical Polyethylene Storage Tank[2] [3] 2500 gal. CLD 23 PE
VT2500-96 Vertical Tank [1] 2500 gal. CLD 23 MLTPL
VT3000-90 Vertical Polyethylene Storage Tank[2] [3] 3000 gal. CLD 23 PE
VT3000-96 Vertical Tank [1] 3000 gal. CLD 23 MLTPL
VT3100-102 Vertical Polyethylene Storage Tank[2] [3] 3100 gal. CLD 23 PE
VT3400-102 Vertical Polyethylene Storage Tank[2] [3] 3400 gal. CLD 23 PE
VT4000-96 Vertical Polyethylene Storage Tank[2] [3] 4000 gal. CLD 23 PE
VT4200-96 Vertical Polyethylene Storage Tank[2] [3] 4200 gal. CLD 23 PE
VT5000-102 Vertical Polyethylene Storage Tank[2] [3] 5000 gal. CLD 23 PE
VT5150-102 Vertical Polyethylene Storage Tank[2] [3] 5150 gal. CLD 23 PE
VT6250-102 Vertical Polyethylene Storage Tank[2] [3] 6250 gal. CLD 23 PE
VT6500-120 Vertical Polyethylene Storage Tank[2] [3] 6500 gal. CLD 23 PE
VT7000-142 Vertical Polyethylene Storage Tank[2] [3] 7000 gal. CLD 23 PE
VT7800-120 Vertical Polyethylene Storage Tank[2] [3] 7800 gal. CLD 23 PE
VT8000-120 Vertical Polyethylene Storage Tank[2] [3] 8000 gal. CLD 23 PE
VT9000-142 Vertical Tank [1] 9000 gal. CLD 23 MLTPL
VT9150-120 Vertical Polyethylene Storage Tank[2] [3] 9150 gal. CLD 23 PE
VT9500-120 Vertical Polyethylene Storage Tank[2] [3] 9500 gal. CLD 23 PE

[1] Certified for the following tank/component combinations:
    3/4" fittings/fitting gaskets shall only be used with tanks greater than or equal to 2.5
    gallons.
    1" fittings/fitting gaskets shall only be used with tanks greater than or equal to 3
    gallons.
    1-1/4" and 1-1/2" fittings/fitting gaskets shall only be used with tanks greater than or
    equal to 4 gallons.
    2" fittings/fitting gaskets shall only be used with tanks greater than or equal to 5
    gallons.
    3" fittings/fitting gaskets shall only be used with tanks greater than or equal to 95
    gallons.
    Siphon tubes shall only be used with tanks greater than or equal to 5 gallons.
[2] Certified for Vertical Tank (VT) and Double Walled (DW) shells that are black, blue,
    green, or natural.
[3] Certified for cistern tank shells that are blue.
[4] Certification for the Double Walled (DW) Vertical Tanks does not include the optional
    fitting system



 
Aclarus Inc. 
1901 Fisher Drive
Peterborough, ON K9J 6X6 
Canada 
888-405-8801 
705-775-8695
Visit this company's website


Facility : Peterborough, Ontario, Canada

Mechanical Devices

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Chemical Generators[1]
AOWT-15 [2] CLD 23 MLTPL
AOWT-20 [2] CLD 23 MLTPL
AOWT-30 [2] CLD 23 MLTPL
AOWT-4 [2] CLD 23 MLTPL
AOWT-45 [2] CLD 23 MLTPL
AOWT-60 [2] CLD 23 MLTPL
AOWT-7 [2] CLD 23 MLTPL

[1] This product is Certified for point-of-entry applications.  This product is not
    Certified for point of use applications. Certification of this product has been
    performed to the health effects requirements of NSF/ANSI Standard 61, which assesses the
    acceptability of potential extractants from the chemical generator.  No evaluation shall
    be performed on the strength or efficacy of the chemical(s) generated.  As unit
    operation, maintenance and the consistency of source ingredients may affect the
    performance of the unit, the ensuing chemical(s) is not Certified by NSF to NSF/ANSI
    Standard 60.
[2] The number in the trade name refers to the flow capacity in gallons per minute (gpm).



 
ACPP Custom Plumbing Parts, ULC 
10037-96 Avenue
Westlock, AB T7P-2P9 
Canada 
780-349-6511


Facility : Westlock, Alberta, Canada

Mechanical Devices

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Manifolds
Copper Manifolds [1] C. HOT CU

[1] The following part numbers, configurations and sizes are Certified.  All manifolds are
    72" long (unless otherwise noted) and may be cut to the desired length.
    
    Copper Manifolds with Copper Ports:
    
    Pipe run 1", 1 1/4", 1 1/2" or 2" with 24 1/2", 3/4", or 1" copper outlets on 3" CTRS.
    
    CC1005024 1 X 1/2 CU
    CC1255024 1 1/4 X 1/2 CU
    CC1251024 1 1/4 X 1 CU
    CC1505024 1 1/2 X 1/2 CU
    CC1501024 1 1/2 X 1 CU
    CC2005024 2 X 1/2 CU
    CC1007524 1 X 3/4 CU
    CC1257524 1 1/4 X 3/4 CU
    CC1507524 1 1/2 X 3/4 CU
    CC2007524 2 X 3/4 CU
    CC2001024 2 X 1 CU
    
    Pipe run 1", 1 1/4", 1 1/2" or 2" with 18 1/2", 3/4", or 1" copper outlets on 4" CTRS
    
    CC1005018 1 X 1/2 CU
    CC1255018 1 1/4 X 1/2 CU
    CC1505018 1 1/2 X 1/2 CU
    CC2005018 2 X 1/2 CU
    CC1007518 1 X 3/4 CU
    CC1257518 1 1/4 X 3/4 CU
    CC1507518 1 1/2 X 3/4 CU
    CC2007518 2 X 3/4 CU
    CC1251018 1 1/4 X 1 CU
    CC1501018 1 1/2 X 1 CU
    CC2001018 2 X 1 CU
    
    Pipe run 1", 1 1/4", 1 1/2" or 2" with 12 1/2", 3/4", or 1" copper outlets on 6" CTRS.
    
    CC1005012ER 1 X 1/2 CU
    CC1255012ER 1 1/4 X 1/2 CU
    CC1505012ER 1 1/2 X 1/2 CU
    CC2005012ER 2 X 1/2 CU
    CC1007512ER 1 X 3/4 CU
    CC1257512ER 1 1/4 X 3/4 CU
    CC1507512ER 1 1/2 X 3/4 CU
    CC2007512ER 2 X 3/4 CU
    CC1251012ER 1 1/4 X 1 CU
    CC1501012ER 1 1/2 X 1 CU
    CC2001012ER 2 X 1 CU
    
    Pipe run 62" long, 1" with 30 1/2" copper outlets on 2" CTRS.
    
    CC1005030 1 X 1/2 CU
    
    Compact Headers - Pipe run 1" with 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, or 12 1/2" copper
    outlets on 1 1/2" CTRS.
    
    CC1005002 1 X 1/2 CU
    CC1005003 1 X 1/2 CU
    CC1005004 1 X 1/2 CU
    CC1005005 1 X 1/2 CU
    CC1005006 1 X 1/2 CU
    CC1005007 1 X 1/2 CU
    CC1005008 1 X 1/2 CU
    CC1005009 1 X 1/2 CU
    CC1005010 1 X 1/2 CU
    CC1005011 1 X 1/2 CU
    CC1005012 1 X 1/2 CU
    
    Speedy Copper Headers - closed one end and reduced 3/4" female sweat the other end.
    
    SC1005002RC 1 X 1/2 CU
    SC1005003RC 1 X 1/2 CU
    SC1005004RC 1 X 1/2 CU
    SC1005005RC 1 X 1/2 CU
    SC1005006RC 1 X 1/2 CU
    SC1005007RC 1 X 1/2 CU
    SC1005008RC 1 X 1/2 CU
    SC1005009RC 1 X 1/2 CU
    SC1005010RC 1 X 1/2 CU
    SC1005011RC 1 X 1/2 CU
    SC1005012RC 1 X 1/2 CU
    
    Speedy Copper Headers - closed one end and 1" plain the other end.
    
    SC1005002PL 1 X 1/2 CU
    SC1005003PL 1 X 1/2 CU
    SC1005004PL 1 X 1/2 CU
    SC1005005PL 1 X 1/2 CU
    SC1005006PL 1 X 1/2 CU
    SC1005007PL 1 X 1/2 CU
    SC1005008PL 1 X 1/2 CU
    SC1005009PL 1 X 1/2 CU
    SC1005010PL 1 X 1/2 CU
    SC1005011PL 1 X 1/2 CU
    SC1005012PL 1 X 1/2 CU
    
    Copper Manifolds with PEX Valves:
    
    Type L Copper Manifold with a Lead Free PEX Valve
    1", 1 1/4", 1 1/2", and 2" Copper Headers with 1/2" Lead Free PEX Valves on 3" Center
    
    CX1005024V-LF 1" x 1/2" Copper outlets with a 1/2" Lead free PEX Valve
    CX1255024V-LF 1 1/4" x 1/2" Copper outlets with a 1/2" Lead free PEX Valve
    CX1505024V-LF 1 1/2" x 1/2" Copper outlets with a 1/2" Lead free PEX Valve
    CX2005024V-LF 2" x 1/2" Copper outlets with a 1/2" Lead free PEX Valve
    
    1" or 1 1/4" Copper Header with 2-12 1/2" Lead Free PEX Valves on 2" Centers
    CVP1005002-LF
    CVP1005003-LF
    CVP1005004-LF
    CVP1005005-LF
    CVP1005006-LF
    CVP1005007-LF
    CVP1005008-LF
    CVP1005009-LF
    CVP1005010-LF
    CVP1005011-LF
    CVP1005012-LF
    CVP1255002-LF
    CVP1255002-LF
    CVP1255003-LF
    CVP1255004-LF
    CVP1255005-LF
    CVP1255006-LF
    CVP1255007-LF
    CVP1255008-LF
    CVP1255009-LF
    CVP1255010-LF
    CVP1255011-LF
    CVP1255012-LF
    



 
ActCarb Technology Co., Ltd. 
1F., No. 620, Fengping 1st Road
Daliao District, Kaohsiung City 831 
Taiwan 
886 919519379
Visit this company's website


Facility : Shanxi, China

Process Media

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Granular Activated Carbon[1]
ACTIVATED CARBON [2] CLD 23 GAC

[1] The carbon source is bituminous coal.
[2] Certified for the following Mesh Sizes: 8 x 30, 4 x 8, 12 x 40, 3 x 6, 4 x 8, 8 x 12, 8
    x 16, 8 x 20, 8 x 24, 8 x 28, 8 x 30, 20 x 30, 20 x 40, 20 x 50, 30 x 40, 30 x 50, 30 x
    60, 30 x 80, 30 x 100, 10 x 25, 10 x 30, 12 x 20, 12 x 25, 12 x 30, 12 x 35, 200, 325.

Powdered Activated Carbon[1] [3]
ACTIVATED CARBON 325 mesh CLD 23 PAC

[1] The carbon source is bituminous coal.
[3] This product is certified for a maximum use level of 250 mg/L.

NOTE: Certified for water treatment plant applications.
      This product has not been evaluated for point of use applications.


 
Action Technology 
10610 State Highway 10
Clinton, IL 61727 
United States 
217-935-1066


Facility : Clinton, IL

Pipes and Related Products

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Tubing/Hose
AT Alpha PE Series .17" - .5" C. HOT PE



 
Activcarb 
SF No. 270/ 1, Chinnaputhur
Dharapuram, Dist Erode 
Tamil Nadu 638657 
India 
91 999 4063307


Facility : Tamil Nadu, India

Process Media

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Granular Activated Carbon[1]
Acb100 [2] CLD 23 GAC
Acb40 [2] CLD 23 GAC
Acb45 [2] CLD 23 GAC
Acb50 [2] CLD 23 GAC
Acb55 [2] CLD 23 GAC
Acb60 [2] CLD 23 GAC
Acb65 [2] CLD 23 GAC
Acb70 [2] CLD 23 GAC
Acb75 [2] CLD 23 GAC
Acb80 [2] CLD 23 GAC
Acb85 [2] CLD 23 GAC
Acb90 [2] CLD 23 GAC
Acb95 [2] CLD 23 GAC

[1] The carbon source is coconut shell.
[2] Certified for the following mesh sizes: 3x6, 3x30, 6x8, 4x8, 6x12, 6x16, 8x16, 8x20,
    8x30, 12x30, 12x40, 14x25, 16x35, 16x40, 18x35, 18x40, 20x40, 20x50, 20x60, 20x70,
    30x50, 30x60, 30x70, 30x80, 35x60, 35x70 and 40x80.

Powdered Activated Carbon[1]
Acb1000 [3] CLD 23 PAC
Acb1050 [3] CLD 23 PAC
Acb1100 [3] CLD 23 PAC
Acb1150 [3] CLD 23 PAC
Acb1200 [3] CLD 23 PAC
Acb1250 [3] CLD 23 PAC
Acb1300 [3] CLD 23 PAC
Acb1350 [3] CLD 23 PAC
Acb1400 [3] CLD 23 PAC
Acb1450 [3] CLD 23 PAC
Acb1500 [3] CLD 23 PAC
Acb950 [3] CLD 23 PAC

[1] The carbon source is coconut shell.
[3] Certified for the following mesh sizes: 40x140, 50x140, 50x200, 80x140, 80x200, 80x325,
    100x325, -200 and -325.

NOTE: Certified for water treatment plant applications.
      This product has not been evaluated for point of use applications.


 
ADA Carbon Solutions, LLC 
1460 West Canal Court
Suite 100 
Littleton, CO 80120 
United States 
888-822-8617 
303-962-1977
Visit this company's website


Facility : # 1 USA

Process Media

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Granular Activated Carbon
PowerGAC[1] [2] [3] CLD 23 GAC

[1] The carbon source is coal, wood, and/or coconut.
[2] Trade names may include letters and/or numbers to designate any or all of the following:
    mesh size, customer, market, processing methods, intended applications, activity level,
    special testing, or other customer or product specific differentiators.
[3] Certified for the following mesh sizes: 8x16, 8x20, 8x30, 10x20, 12x40, 20x40, 20x50,
    30x60, 30x200, 80x325.

Powdered Activated Carbon
PowerPAC H20® Plus[1] [2] -325 mesh CLD 23 PAC
PowerPAC H2O®[1] [2] -325 mesh CLD 23 PAC

[1] The carbon source is coal, wood, and/or coconut.
[2] Trade names may include letters and/or numbers to designate any or all of the following:
    mesh size, customer, market, processing methods, intended applications, activity level,
    special testing, or other customer or product specific differentiators.

NOTE: Certified for water treatment plant applications.
      This product has not been evaluated for point of use applications.


Facility : # 2 USA

Process Media

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Granular Activated Carbon[1] [2]
PowerGAC [3] CLD 23 GAC

[1] The carbon source is coal, wood and/or coconut.
[2] Trade names may include letters and/or numbers to designate any or all of the following:
    mesh size, customer, market, processing methods, intended applications, activity level,
    special testing, or other customer or product specific differentiators.
[3] Certified for the following mesh sizes: >4, 4x8, 8x16, 8x20, 8x30, 10x20, 12x40, 20x40,
    20x50, 30x60, 30x200, 80x325.

Powdered Activated Carbon[1] [2]
PowerPAC H20® -325 mesh CLD 23 PAC
PowerPAC H20® Plus -325 mesh CLD 23 PAC

[1] The carbon source is coal, wood and/or coconut.
[2] Trade names may include letters and/or numbers to designate any or all of the following:
    mesh size, customer, market, processing methods, intended applications, activity level,
    special testing, or other customer or product specific differentiators.

NOTE: Certified for water treatment plant applications.
      This product has not been evaluated for point of use applications.


 
AdEdge Technologies, Inc. 
5152 Belle Wood Court
Suites A 
Burford, GA 30518 
United States 
678-835-0052


Facility : Quincy, IL

Process Media

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Oxidative Media
AD26 [1] CLD 23 MNDOX

[1] Certified for the following mesh sizes: 8 x 20, 20 x 40.

NOTE: Certified for water treatment plant applications.
      This product has not been evaluated for point of use applications.


 
Adeka Corporation 
7-2-35 Higashiogu
Arakawa-ku, Toyko, 116-8554 
Japan 
81 3 4455 2843
Visit this company's website


Facility : Ibaraki, Japan

Joining and Sealing Materials

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Gasket/Sealing Materials
ADEKAULTRASEAL MC-2010MN [1] CLD 23 IR

[1] Certified for a maximum surface area to volume ratio not to exceed 0.13 sq. in./L.



 
Adhesive R&D, Inc. 
4603 Anderson Drive
Eau Claire, WI 54703 
United States 
715-832-4557
Visit this company's website


Facility : Eau Claire, WI

Joining and Sealing Materials

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Thread Compounds
DFM 555 [1] CLD 23 SLT
DFM 63 [1] CLD 23 SLT
DFM 64 [1] CLD 23 SLT
DFM 65 [1] CLD 23 SLT
DFM 66 [1] CLD 23 SLT
DFM 67 [1] CLD 23 SLT
DFM 68 [1] CLD 23 SLT
FMB64 [1] CLD 23 SLT
FMB65 [1] CLD 23 SLT
FMB66 [1] CLD 23 SLT
RubberMAX iPipe 70 [1] CLD 23 SLT
RubberMAX iPipe 71 [1] CLD 23 SLT
RubberMAX iPipe 72 [1] CLD 23 SLT
RubberMAX iPipe 73 [1] CLD 23 SLT

[1] Certified for a maximum of 18.5 joints per liter.



 
Adhesives Technology Corp. 
450 East Copans Road
Pompano Beach, FL 33064 
United States 
954-461-2335


Facility : # 2 Germany

Joining and Sealing Materials

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Adhesives
ULTRABOND ACRYL-8CC [1] D. HOT VE

[1] Certified for use as an anchoring adhesive for installing thread rods (less than or
    equal to 1.3 inches in diameter) in concrete or masonry for water treatment applications.

NOTE: Only products bearing the NSF Mark on the products, product packaging, and/or
      documentation shipped with the product are certified.


Adhesives Technology Corp. (ATC) 
450 East Copans Road
Pompano Beach, FL 33064 
United States 
800-892-1880 
Visit this company's website


Facility : # 1 Germany

Joining and Sealing Materials

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Adhesives
ULTRABOND 365CC 13.2 fl. oz. [1] C. HOT VE
ULTRABOND 365CC 19.8 fl. oz. [1] C. HOT VE

[1] Certified for use as an anchoring adhesive for installing threaded rods (less than or
    equal to 6 mm - 36 mm or 1/4" - 1-3/8" in diameter) in concrete for water treatment
    applications.



 
Adolf Würth GmbH & Co. KG 
Produktmanagement Chemie, Postfach
74650 Künzelsau 
Germany 
49 794 015 2007


Facility : # 1 Switzerland

Joining and Sealing Materials

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Adhesives
Würth® DOS Lagersicherung hochfest (0893 603) >= 1/2" C. HOT ADH
Würth® DOS Flächendicht orange (0893 574) >= 1/2" C. HOT ADH
Würth® DOS Klebfix EASY PEN (0893 090) >= 1/2" CLD 23 ADH
Würth® DOS Klebfix (0893 09) >= 1/2" CLD 23 ADH
Würth® DOS Schraubensicherung Hochfest >= 1/2" C. HOT ADH
Würth® DOS Schraubensicherung Mittelfest >= 1/2" C. HOT ADH
Würth Rohrdicht PLUS (0893 577 300) >= 1/2" C. HOT ADH

Sealants
Würth® DOS Flächendicht grün (0893 573) >= 1/2" C. HOT SLT

Thread Compounds
Würth® DOS Rohrdicht mit PTFE >= 1/2" C. HOT TC
Würth® DOS Rohrdicht[1] >= 1/2" C. HOT TC
Würth® DOS Schraubensicherung Hochfest >= 1/2" C. HOT TC

[1] Certification is based on a minimum cure of 72 hours at 75°F.



 
Adolf Würth GmbH & Co. KG 
Reinhold-Würth-Str. 12-16
74653 Künzelsau-Gaisbach 
Germany 
49 7940 15 0


Facility : # 2 Germany

Joining and Sealing Materials

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Adhesives
Atrion AVM TOP QUATTRO [1] D. HOT VE
WIT-PE 500 [1] D. HOT EPOXY
WIT-UH 300 [1] C. HOT PUR
WIT-VH 300 [1] C. HOT PUR
WIT-VM 250 [1] D. HOT VE
WIT-VM 300 [1] C. HOT PUR

[1] Certified for use as an anchoring adhesive for installing thread rods (less than or
    equal to 1.3 inches in diameter) in concrete or masonry for water treatment applications.

NOTE: Only products bearing the NSF Mark on the product, product packaging, and/or
      documentation shipped with the product are Certified.


 
Adolf Würth GmbH & Co. KG 
Reinhold-Würth-Strasse 12-17
D-74650 Künzelsau, Baden-Wurttemberg 
Germany 
49 7940150
Visit this company's website


Facility : # 1 Germany

Joining and Sealing Materials

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Sealants[G]
SILICONE ACETATE, FOOD GRADE / ACETATSILIKON LEBENSMITTEL >= 1/2" CLD 23 SLT

[G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for
    “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state
    laws and the U.S. Safe Drinking Water Act.

    



 
Advance Products & Systems 
108 Asset Avenue
Scott, LA 70583 
United States 
800-315-6009 
337-233-6116
Visit this company's website


Facility : Scott, LA

Pipes and Related Products

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Dielectric Insulator[1]
Trojan G-10, Type ET 1/2" - 160" D. HOT MLTPL
Trojan G-10, Type FT 1/2" - 160" D. HOT MLTPL

[1] Certified for 1/8" thick flange insulating gaskets.



 
Advanced Component Services 
1420 19th Avenue Northwest
Issaquah, WA 98027 
United States 
425-391-1572


Facility : Chang Hua, Taiwan

Mechanical Plumbing Devices

Trade Designation      

Faucets

Dispenser Series
MET012      
MET012-B      
MET012-O      
MET127      
MET127-B      
MET127-O      
MET130(Low Lead Brass)      
MET130-RC      
MET133      
MET133(Low Lead Brass)      
MET133-OD      
MET133-R      
MET133-RW      
MET133-SBRH      
MET133-SBRH(Normal Brass)      
MET138      
MET138-OD      
MET138-R      
MET138-RW      
PLA131      
PLA131-OD      
PLA131-R      
PLA131-RW      

Pre-Rinse Assembly Series[G]
MET170-UN      
MET170-UNSG      
MET170-WN      
MET170-WNSG      

[G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for
    “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state
    laws and the U.S. Safe Drinking Water Act.

    



 
Advanced Electronics Company 
King Khalid International Airport
Industrial Estate P.O. Box 90916 
Riyadh 11623 
Saudi Arabia 
966 1 122 01350
Visit this company's website


Facility : Marlborough, MA

Mechanical Devices

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Water Meters [G]
wADDAD™ Series 280W-CI[2] 2" - 12" CLD 23 MLTPL
wADDAD™ Series 280W-R[1] [2] D. HOT MLTPL

[1] Domestic hot - The temperature used during testing is 60 +/- 2°C (140 +/- 4 °F) and
    appears in Listings as "D. Hot". This is intended to apply to product applications where
    the product is used for either cold (ambient temperatures) or hot water up to domestic
    hot temperatures.
[2] Meter Size:
    1/2"
    5/8" x 3/4"
    3/4"
    1"
    1 1/4"
    1 1/2"
[G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for
    “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state
    laws and the U.S. Safe Drinking Water Act.

    



 
Advanced Piping Solutions Company for Industry 
2nd Industrial Area, Street No.39
Cross 150, P.O. Box 5794 
Dammam 31432 
Saudi Arabia 
966 381 27766
Visit this company's website
Temp Material
Fittings, Non-Repeating[G] 710 Series Male Pipe Transition 1/2" - 12" CLD 23 MLTPL 914 Series Flare Nut Swivel Transition 3/4" - 2" CLD 23 MLTPL
[G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for
    “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state
    laws and the U.S. Safe Drinking Water Act.

    



 
Polyflex Division of Flex Technologies Inc. 
5479 Gundy Drive
P.O. Box 400 
Midvale, OH 44653 
United States 
740-922-5992
Visit this company's website


Facility : Baltic, OH

Potable Water Materials

    Water Water
    Contact Contact
Trade Designation End Use Temp Material

Potable Water Materials
Polyflex FPVC Transparent Blue-Violet Series[1] [G] P CLD 23 FPVC

[1] Shore A Hardness: 65-95 Durometer
[G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for
    “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state
    laws and the U.S. Safe Drinking Water Act.

    



 
Polymem SA 
3, rue de l'industrie
ZI de Vic 
31320 Castanet Tolosan 
France 
33 561 317 866
Visit this company's website


Facility : Castanet Tolosan, France

Mechanical Devices

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Microfiltration Devices[1]
MF80 [2] CLD 23 MLTPL
MF80 PVDF NEOPHIL [2] CLD 23 MLTPL
MF100L [3] CLD 23 MLTPL
MF100L PVDF NEOPHIL [3] CLD 23 MLTPL
MF100LL [4] CLD 23 MLTPL
MF100LL PVDF NEOPHIL [4] CLD 23 MLTPL
MF100XL [5] CLD 23 MLTPL
MF100XL PVDF NEOPHIL [5] CLD 23 MLTPL
MF120 [6] CLD 23 MLTPL
MF120 PVDF NEOPHIL [6] CLD 23 MLTPL
MF240[9] [7] CLD 23 MLTPL
MF240 PVDF NEOPHIL [7] CLD 23 MLTPL

[1] Product requires a 500L/h flush for 24 hours with potable water before being placed into
    service.
[2] Testing and evaluation based on a minimum flow of 30,200 L/day.
[3] Testing and evaluation based on a minimum flow of 3,200 L/day.
[4] Testing and evaluation based on a minimum flow of 8,733 L/day.
[5] Testing and evaluation based on a minimum flow of 4,300 L/day.
[6] Testing and evaluation based on a minimum flow of 82,000 L/day.
[7] Testing and evaluation based on a minimum flow of 371,000 L/day.
[9] This module includes hollow fiber membrane elements UF2555, MF2555, UF2555 PVDF NEOPHIL
    et MF2555 PVDF NEOPHIL.

Ultrafiltration Devices
UF80[1] [2] CLD 23 MLTPL
UF-80 G Housing [8] [10] CLD 23 MLTPL
UFMF80G [8] [10] CLD 23 MLTPL
UFMF80G PVDF NEOPHIL [8] [10] CLD 23 MLTPL
UF80 PVDF NEOPHIL[1] [2] CLD 23 MLTPL
UF100L[1] [3] CLD 23 MLTPL
UF100L PVDF NEOPHIL[1] [3] CLD 23 MLTPL
UF100LL[1] [4] CLD 23 MLTPL
UF100LL PVDF NEOPHIL[1] [4] CLD 23 MLTPL
UF100XL[1] [5] CLD 23 MLTPL
UF100XL PVDF NEOPHIL[1] [5] CLD 23 MLTPL
UF120[1] [6] CLD 23 MLTPL
UF120 PVDF NEOPHIL[1] [6] CLD 23 MLTPL
UF240[1] [9] [7] CLD 23 MLTPL
UF240 PVDF NEOPHIL[1] [7] CLD 23 MLTPL

[1] Product requires a 500L/h flush for 24 hours with potable water before being placed into
    service.
[2] Testing and evaluation based on a minimum flow of 30,200 L/day.
[3] Testing and evaluation based on a minimum flow of 3,200 L/day.
[4] Testing and evaluation based on a minimum flow of 8,733 L/day.
[5] Testing and evaluation based on a minimum flow of 4,300 L/day.
[6] Testing and evaluation based on a minimum flow of 82,000 L/day.
[7] Testing and evaluation based on a minimum flow of 371,000 L/day.
[8] Testing and evaluation based on a minimum flow of 60,000 liters per day.
[9] This module includes hollow fiber membrane elements UF2555, MF2555, UF2555 PVDF NEOPHIL
    et MF2555 PVDF NEOPHIL.
[10] Models UFMF80G and UFMF80G PVDF NEOPHIL require a 117 L/min flush with 11613 liters of
     tap water before being placed into service.



 
Polymeric Systems, Inc. 
47 Park Avenue
Box 522 
Elverson, PA 19520 
United States 
610-286-2500


Facility : Elverson, PA

Joining and Sealing Materials

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Patching Materials
AQUAMEND® White [1] C. HOT EPOXY
IF RepairitQuik [1] C. HOT EPOXY
Quikplastik® [1] C. HOT EPOXY

[1] The exposed surface area of each sealant in a household distribution system shall not
    exceed 1.3 sq. cm/L or .2 sq. in./L

Sealants
E20M12[G] [1] C. HOT EPOXY
Faststeel®[G] [1] C. HOT EPOXY
GR10[G] >= 1/2" C. HOT EPOXY
PSI Poxy [1] C. HOT EPOXY
Quikcopper® [1] C. HOT EPOXY
Repairitquik®[G] [1] C. HOT EPOXY

[1] The exposed surface area of each sealant in a household distribution system shall not
    exceed 1.3 sq. cm/L or .2 sq. in./L
[G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for
    “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state
    laws and the U.S. Safe Drinking Water Act.

    



 
Polynt Composites USA Inc. 
99 East Cottage Avenue
Carpentersville, IL 60110 
United States 
800-322-8103 
847-428-2657
Visit this company's website


Facility : Pensacola, FL

Protective (Barrier) Materials

    Water Water
  Water Contact Contact Contact
Trade Designation Size Restriction Temp Material

Resin
DION® 9102-00[1] [2] [3] CLD 23 VE
DION® IMPACT 9102-70 (US)[1] [2] [4] CLD 23 VE

[1] Please refer to the Polynt Composites USA Inc. Product Bulletin for system requirements.
[2] Colors: N/A
    Number of Coats: 1
    Maximum Field Use Dry Film Thickness (in mils): 10
    Maximum Thinner: N/A
    Cure Time: 2 - 100 hours at ambient temperature
    Final Cure: 4 hours at 160°F followed by 2 hours at 180°F
[3] DION® 9102-00 is Certified for use as the resin in coating systems on pipes 1/2" and
    greater and tanks 150 gallons and greater.  It may also be applied as a coating system
    alone.
[4] DION® IMPACT 9102-70 (US) is Certified for use as the resin in coating systems on pipes
    6" and greater and tanks 150 gallons and greater.  It may also be applied as a coating
    system alone.



 
PolyOne Corporation 
Avon Lake General Chemical
33587 Walker Road 
Avon Lake, OH 44012 
United States 
440-930-1000
Visit this company's website


Facility : Carson, CA

Potable Water Materials

    Water Water
    Contact Contact
Trade Designation End Use Temp Material

Potable Water Materials[1]
210 Gray 2700 (HR)[2] A,F CLD 23 PVC
210 White 1271 (HR)[2] A,F CLD 23 PVC
210 White 1271 (HS)[2] A,F CLD 23 PVC
210 White 1494[2] A,F CLD 23 PVC
210 White 271[2] A,F CLD 23 PVC
210A Gray 172[2] A,F CLD 23 PVC
210A White 1271 (HS)[2] A,F CLD 23 PVC
216A Gray 172[2] A,F CLD 23 PVC
216A White 278[2] A,F CLD 23 PVC
78761 Black 2999 A,F CLD 23 PVC
78761 Natural 0000 A,F CLD 23 PVC
86155 White 1000[3] A,F,P CLD 23 PVC
8700A Black 2960[4] A,F CLD 23 PVC
8700A Gray 2440[4] A,F CLD 23 PVC
8700A Gray 2600[4] A,F CLD 23 PVC
8700A White 1190[4] A,F CLD 23 PVC
8700A White 1320[4] A,F CLD 23 PVC
87345 White 1000 A,F CLD 23 PVC
87345 White 1270 A,F CLD 23 PVC
87580 Transparent 9499 A,F,P CLD 23 PVC
Geon L8801 Gray 2730[2] A, F CLD 23 PVC
I0210 Green 5133[2] A,F CLD 23 PVC
M1000 Black 2880[2] A,F CLD 23 PVC
M1000 Gray 2402[2] A,F CLD 23 PVC
M1000 Gray 2700[2] A,F CLD 23 PVC
M1000 White 1114[2] A,F CLD 23 PVC
M1000 White 1240[2] A,F CLD 23 PVC
M1012 WHITE 1235[2] A,F CLD 23 PVC
M1012 White 1244 A,F CLD 23 PVC
M1015 Black 2880[2] A,F CLD 23 PVC
M1015 GRAY 2132[2] A,F CLD 23 PVC
M1015 Gray 2709[2] A,F CLD 23 PVC
M1015 WHITE 1235[2] A,F CLD 23 PVC
M1018 White 1424 A,F CLD 23 PVC
M1021 White 1424 A, F CLD 23 PVC
M1022 Orange 7296 A,F CLD 23 PVC
M1030 Gray 2709[2] A,F CLD 23 PVC
M1030 White 1424[2] A,F CLD 23 PVC
M1090 Black 2880 A,F CLD 23 PVC
M1100 White 1240[2] A,F CLD 23 PVC
M1210 Black 2880[2] A,F CLD 23 PVC
M1210 Gray 2306[2] A,F CLD 23 PVC
M1210 Gray 2580[2] A,F CLD 23 PVC
M1210 Gray 2600[2] A,F CLD 23 PVC
M1210 Gray 2700[2] A,F CLD 23 PVC
M1210 Green 5237[2] A,F CLD 23 PVC
M1210 Green 5255[2] A,F CLD 23 PVC
M1210 Light Grey 2863[2] A,F CLD 23 PVC
M1210 Natural 0000[2] A,F CLD 23 PVC
M1210 White 1240[2] A,F CLD 23 PVC
M3000 Black 2880[2] A,F CLD 23 PVC
M3000 Gray 2700[2] A,F CLD 23 PVC
M3000 Natural 0000[2] A,F CLD 23 PVC
M3000 White 1240[2] A,F CLD 23 PVC
M3220 Gray 2440[2] A,F CLD 23 PVC
M3220 White 1240[2] A,F CLD 23 PVC
M4300 Transparent 9498 F CLD 23 PVC
M5100 Beige 3190[2] A,F CLD 23 PVC
M5100 Gray 2448[2] A,F CLD 23 PVC
M5100 Green 5245[2] A,F CLD 23 PVC
M5100 Green 5255[2] A,F CLD 23 PVC
M5100 Taupe 2386[2] A,F CLD 23 PVC
M5100 White 1231[2] A,F CLD 23 PVC
M5200 Light Brown 3365[2] A,F CLD 23 PVC
M5240 Black 2880 F CLD 23 PVC
M5240 Desert Sand 3375 F CLD 23 PVC
M5240 Gray 2680 F CLD 23 PVC
M5240 White 1745 F CLD 23 PVC
MC100 Gray 2481 F C. HOT CPVC
MC100 Tan 3189 F C. HOT CPVC
MC100 White 1000 F C. HOT CPVC
MC200 Gray 2481 F C. HOT CPVC
MC250 Gray 2481 F C. HOT CPVC
MC270 Gray 2481 F C. HOT CPVC
MC280 Black 2878 F C. HOT CPVC
MC280 Gray 2124 F C. HOT CPVC
MC280 Gray 2481 F C. HOT CPVC
MC280 Gray 2867 F C. HOT CPVC
MC550 Black 2999 F C. HOT CPVC
MC550 Gray 2158 F C. HOT CPVC
MC550 Tan 3447 F C. HOT CPVC
MC550 White 1406 F C. HOT CPVC
White 1279[2] A,F CLD 23 PVC

[1] Material designation may or may not include the designation "Geon".
    Trade designation of product may or may not be followed by either a PL or CU:
    PL - Pellet
    CU - Cube
[2] Maximum surface area to volume ratio is 250 sq. in./L.
[3] Maximum surface area to volume ratio is 160 sq. in./L.
[4] Maximum surface area to volume ratio is 225 sq. in./L.

NOTE: All Listed products from this facility are NSF Certified, whether or not they bear the
      NSF Mark.


Facility : Terre Haute, IN

Potable Water Materials

    Water Water
    Contact Contact
Trade Designation End Use Temp Material

Potable Water Materials[1]
210 Gray 2700 (HR)[2] A,F CLD 23 PVC
210 White 1271 (HR)[2] A,F CLD 23 PVC
210 White 1271(HS)[2] A,F CLD 23 PVC
210 White 1494[2] A,F CLD 23 PVC
210 White 271[2] A,F CLD 23 PVC
210A Gray 172[2] A,F CLD 23 PVC
210A White 1271 (HS)[2] A,F CLD 23 PVC
210A White 1279[2] A,F CLD 23 PVC
216A Gray 172[2] A,F CLD 23 PVC
216A White 278[2] A,F CLD 23 PVC
52310 Gray 2300 F CLD 23 PVC
81510 Black 2999 F CLD 23 PVC
81520 Black 2999 F CLD 23 PVC
81520 Gray 2042 F CLD 23 PVC
81520 Gray 2722 F CLD 23 PVC
81530 Black 2999 F CLD 23 PVC
81530 Gray 2722 F CLD 23 PVC
81530 Natural 0000 F CLD 23 PVC
86155 White 1000[3] A,F,P CLD 23 PVC
87345 Natural 0000 A,F CLD 23 PVC
87345 White 1000 A,F CLD 23 PVC
87345 White 1270 A,F CLD 23 PVC
87580 Transparent 9499 A,F,P CLD 23 PVC
Geon A88065 TRANS 9034 P D. HOT FPVC
I0210 Green 5133[2] A,F CLD 23 PVC
L0189 Transparent 9000 P CLD 23 PVC
M1000 Black 2880[2] A,F CLD 23 PVC
M1000 Gray 2700[2] A,F CLD 23 PVC
M1000 White 1114[2] A,F CLD 23 PVC
M1000 White 1240[2] A,F CLD 23 PVC
M1012 White 1244[2] A,F CLD 23 PVC
M1015 Black 2880[2] A,F CLD 23 PVC
M1015 GRAY 2132[2] A,F CLD 23 PVC
M1015 Gray 2709[2] A,F CLD 23 PVC
M1015 WHITE 1235[2] A,F CLD 23 PVC
M1018 White 1424 A,F CLD 23 PVC
M1021 White 1424 A, F CLD 23 PVC
M1022 Orange 7296 A,F CLD 23 PVC
M1030 Gray 2709[2] A,F CLD 23 PVC
M1030 White 1424[2] A,F CLD 23 PVC
M1090 Black 2880 A,F CLD 23 PVC
M1100 White 1240[2] F CLD 23 PVC
M1200 White 1240[2] F CLD 23 PVC
M1210 Black 2880[2] F CLD 23 PVC
M1210 Gray 2306[2] F CLD 23 PVC
M1210 Gray 2580[2] A,F CLD 23 PVC
M1210 Gray 2600[2] A,F CLD 23 PVC
M1210 Gray 2700[2] F CLD 23 PVC
M1210 Green 5237[2] A F CLD 23 PVC
M1210 Green 5255[2] F CLD 23 PVC
M1210 Light Grey 2863[2] A,F CLD 23 PVC
M1210 Natural 0000[2] A,F CLD 23 PVC
M1210 White 1240[2] F CLD 23 PVC
M3000 Black 2880[2] A,F CLD 23 PVC
M3000 Gray 2700[2] A,F CLD 23 PVC
M3000 Natural 0000[2] A,F CLD 23 PVC
M3000 White 1240[2] A,F CLD 23 PVC
M3220 Gray 2440[2] F CLD 23 PVC
M3220 White 1240[2] F CLD 23 PVC
M3700 Almond 3017 F CLD 23 PVC
M3700 Almond 3018 F CLD 23 PVC
M3700 Bisque 3228 F CLD 23 PVC
M3700 Black 2975 F CLD 23 PVC
M3700 Gray 2601 P CLD 23 PVC
M3700 Ivory 3010 F CLD 23 PVC
M3700 Natural 0000 F CLD 23 PVC
M3700 Natural 0000 F CLD 23 PVC
M3700 White 1260 F CLD 23 PVC
M3700 White 1360 F CLD 23 PVC
M3800 Almond 3070 F CLD 23 PVC
M3800 Black 2975 F CLD 23 PVC
M3800 Gray 2601 P CLD 23 PVC
M3800 Ivory 3010 F CLD 23 PVC
M3800 Natural 0000 F CLD 23 PVC
M3800 Natural 0000 F CLD 23 PVC
M3800 White 1260 F CLD 23 PVC
M3800 White 1360 F CLD 23 PVC
M4110 Transparent 9496 F CLD 23 PVC
M4300 Transparent 9498 F CLD 23 PVC
M5100 Beige 3190[2] A,F CLD 23 PVC
M5100 Gray 2448[2] A,F CLD 23 PVC
M5100 Green 5245[2] A,F CLD 23 PVC
M5100 Green 5255[2] A,F CLD 23 PVC
M5100 Taupe 2386[2] A,F CLD 23 PVC
M5100 White 1231[2] A,F CLD 23 PVC
M5200 Light Brown 3365[2] A,F CLD 23 PVC
M5240 Black 2880 F CLD 23 PVC
M5240 Desert Sand 3375 F CLD 23 PVC
M5240 Gray 2680 F CLD 23 PVC
M5240 White 1745 F CLD 23 PVC
MP100 Black 2975 F CLD 23 PVC
MP100 Ivory 3010 F CLD 23 PVC
MP100 White 1360 F CLD 23 PVC
MP101 Ivory 3010 F CLD 23 PVC
MP101 White 1360 F CLD 23 PVC
MP130 Black 2975 F CLD 23 PVC
MP130 Ivory 3010 F CLD 23 PVC
MP130 White 1260 F CLD 23 PVC
MP131 Black 2975 F CLD 23 PVC
MP131 Ivory 3010 F CLD 23 PVC
MP131 White 1260 F CLD 23 PVC
MP250 White 1260 F CLD 23 PVC
MP320 Black 2975 F CLD 23 PVC
MP320 Ivory 3010 F CLD 23 PVC
MP321 Black 2975 F CLD 23 PVC
MP321 Ivory 3010 F CLD 23 PVC
MP461 White 1360 F CLD 23 PVC

[1] Material designation may or may not include the designation "Geon".
    Trade designation of product may or may not be followed by either a PL or CU:
    PL - Pellet
    CU - Cube
[2] Maximum surface area to volume ratio is 250 sq. in./L.
[3] Maximum surface area to volume ratio is 160 sq. in./L.

NOTE: All Listed products from this facility are NSF Certified, whether or not they bear the
      NSF Mark.


Facility : Avon Lake 1012, OH

Potable Water Materials

    Water Water
    Contact Contact
Trade Designation End Use Temp Material

Potable Water Materials[1]
210 Gray 2700 (HR)[2] A,F CLD 23 PVC
210 White 1271 (HG) A,F CLD 23 PVC
210 White 1271 (HR)[2] A,F CLD 23 PVC
210 White 1271(HS)[2] A,F CLD 23 PVC
210 White 1494[2] A,F CLD 23 PVC
210 White 271[2] A,F CLD 23 PVC
210A Gray 172[2] A,F CLD 23 PVC
210A White 1271 (HS)[2] A,F CLD 23 PVC
216A Gray 172[2] A,F CLD 23 PVC
216A White 278[2] A,F CLD 23 PVC
52310 Gray 2300 F CLD 23 PVC
6935 White 1410 P CLD 23 PVC
78761 Black 2999 A,F CLD 23 PVC
78761 Gray 2730 A,F CLD 23 PVC
78761 Natural 0000 A,F CLD 23 PVC
78761 White 1270 A,F CLD 23 PVC
81530 Natural 0000 F CLD 23 PVC
82510 Gray 2728 F CLD 23 PVC
86155 White 1000[3] A,F,P CLD 23 PVC
8700A Black 2960[4] A,F CLD 23 PVC
8700A Gray 2440[4] A,F CLD 23 PVC
8700A Gray 2600[4] A,F CLD 23 PVC
8700A White 1190[4] A,F CLD 23 PVC
8700A White 1320[4] A,F CLD 23 PVC
87345 Natural 0000 A,F CLD 23 PVC
87345 White 1000 A,F CLD 23 PVC
87345 White 1270 A,F CLD 23 PVC
E1257 White 1278 F CLD 23 PVC
E1355 White 1278 F CLD 23 PVC
E1356 Gray 2747 P CLD 23 PVC
E1356 Natural 0000 P CLD 23 PVC
E1356 White 1278 P CLD 23 PVC
E1357 White 1278 F CLD 23 PVC
E7364 White 1410[4] A,F CLD 23 PVC
Geon L8801 Gray 2730[2] A, F CLD 23 PVC
I0210 Green 5133[2] A,F CLD 23 PVC
L0189 Transparent 9000 P CLD 23 PVC
M1000 Gray 2700 F CLD 23 PVC
M1000 White 1114[2] A,F CLD 23 PVC
M1000 White 1240[2] A,F CLD 23 PVC
M1012 White 1244[2] A,F CLD 23 PVC
M1015 Black 2880[2] A,F CLD 23 PVC
M1015 GRAY 2132[2] A,F CLD 23 PVC
M1015 Gray 2709[2] A,F CLD 23 PVC
M1015 WHITE 1235[2] A,F CLD 23 PVC
M1015 White 1424[2] A,F CLD 23 PVC
M1018 White 1424 A,F CLD 23 PVC
M1021 White 1424 A, F CLD 23 PVC
M1022 Orange 7296 A,F CLD 23 PVC
M1030 Gray 2709 F CLD 23 PVC
M1030 White 1424 F CLD 23 PVC
M1200 White 1240[2] A,F CLD 23 PVC
M1210 Black 2880[2] A,F CLD 23 PVC
M1210 Gray 2306[2] A,F CLD 23 PVC
M1210 Gray 2580[2] A,F CLD 23 PVC
M1210 Gray 2600[2] A,F CLD 23 PVC
M1210 Gray 2700[2] F CLD 23 PVC
M1210 Green 5237[2] A,F CLD 23 PVC
M1210 Green 5255[2] A,F CLD 23 PVC
M1210 Light Grey 2863[2] A,F CLD 23 PVC
M1210 Natural 0000[2] A,F CLD 23 PVC
M1210 White 1240[2] A,F CLD 23 PVC
M3000 Gray 2700[2] A,F CLD 23 PVC
M3700 Almond 3017 F CLD 23 PVC
M3700 Almond 3018 F CLD 23 PVC
M3700 Almond 3070 F CLD 23 PVC
M3700 Bisque 3228 F CLD 23 PVC
M3700 Black 2975 F CLD 23 PVC
M3700 Ivy 3010 F CLD 23 PVC
M3700 Natural 0000 F CLD 23 PVC
M3700 White 1260 F CLD 23 PVC
M3700 White 1360 F CLD 23 PVC
M3800 Almond 3070 F CLD 23 PVC
M3800 Black 2975 F CLD 23 PVC
M3800 Ivy 3010 F CLD 23 PVC
M3800 Natural 0000 F CLD 23 PVC
M3800 White 1260 F CLD 23 PVC
M3800 White 1360 F CLD 23 PVC
M4110 Transparent 9496 F CLD 23 PVC
M4300 Transparent 9498 F CLD 23 PVC
M5100 Taupe 2386[2] A,F CLD 23 PVC
M5240 Black 2880 F CLD 23 PVC
M5240 Desert Sand 3375 F CLD 23 PVC
M5240 Gray 2680 F CLD 23 PVC
M5240 White 1745 F CLD 23 PVC
MC100 Gray 2481 F C. HOT CPVC
MC100 Tan 3189 F C. HOT CPVC
MC100 White 1000 F C. HOT CPVC
MC270 Gray 2481 F C. HOT CPVC
MC280 Black 2878 F C. HOT CPVC
MC280 Gray 2124 F C. HOT CPVC
MC280 Gray 2481 F C. HOT CPVC
MC280 Gray 2867 F C. HOT CPVC
MP100 Black 2975 F CLD 23 PVC
MP100 Ivory 3010 F CLD 23 PVC

[1] Material designation may or may not include the designation "Geon".
    Trade designation of product may or may not be followed by either a PL or CU:
    PL - Pellet
    CU - Cube
[2] Maximum surface area to volume ratio is 250 sq. in./L.
[3] Maximum surface area to volume ratio is 160 sq. in./L.
[4] Maximum surface area to volume ratio is 225 sq. in./L.

NOTE: All Listed products from this facility are NSF Certified, whether or not they bear the
      NSF Mark.


Facility : Avon Lake 1108, OH

Potable Water Materials

    Water Water
    Contact Contact
Trade Designation End Use Temp Material

Potable Water Materials
NT-818.B001-7001 A,F C. HOT RPP
NT-818.B001-8000-0 A,F C. HOT RPP
Nymax 600 A Natural A,F CLD 23 NP
Nymax 600 A ZIP 32 Natural A A,F CLD 23 NP
Nymax 600 A ZIP 43 Natural A A,F CLD 23 NP
PPC-20G Black A,F C. HOT RPP
PPC-20G Natural A,F C. HOT RPP
PPR-30G Black A,F C. HOT RPP
PPR-30G Natural A,F C. HOT RPP
PPR-40G Black A,F C. HOT RPP
PPR-40G Natural A,F C. HOT RPP



Facility : Dyersburg, TN

Potable Water Materials

    Water Water
    Contact Contact
Trade Designation End Use Temp Material

Potable Water Materials
PPC-20G Natural A,F C. HOT RPP
PPC-20G Black A,F C. HOT RPP
PPR-30G Natural A,F C. HOT RPP
PPR-30G Black A,F C. HOT RPP
PPR-40G Natural A,F C. HOT RPP
PPR-40G Black A,F C. HOT RPP
NT-818.B001-8000-0 A,F C. HOT RPP
NT-818.B001-7001 A,F C. HOT RPP

NOTE: All Listed products from this facility are NSF Certified, whether or not they bear the
      NSF Mark.


Facility : Pasadena, TX

Potable Water Materials

    Water Water
    Contact Contact
Trade Designation End Use Temp Material

Potable Water Materials[1]
E1210 HR White 1271[2] A, F CLD 23 PVC
E1257 White 1278 F CLD 23 PVC
E1353 White 1278 P CLD 23 PVC
E1354 White 1278 P CLD 23 PVC
E1355 White 1278 F CLD 23 PVC
E1356 Gray 2747 P CLD 23 PVC
E1356 Natural 0000 P CLD 23 PVC
E1356 White 1278 P CLD 23 PVC
E1357 White 1278 F CLD 23 PVC
E7364 White 1410[3] A,F CLD 23 PVC
E7755 White 1302[3] A,P CLD 23 PVC
M1000 White 1114[2] A,F CLD 23 PVC

[1] Material designation may or may not include the designation "Geon".
    Trade designation of product may or may not be followed by either a PL or CU:
    PL - Pellet
    CU - Cube
[2] Fitting and appurtenance end use not to exceed 250 sq. in./L.
[3] Maximum surface area to volume ratio is 225 sq. in./L.

NOTE: All Listed products from this facility are NSF Certified, whether or not they bear the
      NSF Mark.


Facility : PolyOne (Dongguan) Vinyl Compounds Co. Ltd. Guangdong Province, China

Potable Water Materials

    Water Water
    Contact Contact
Trade Designation End Use Temp Material

Potable Water Materials[1]
210 Gray 2700 (HR)[2] A,F CLD 23 PVC
210 White 1271 (HR)[2] A,F CLD 23 PVC
210 White 1271 (HS)[2] A,F CLD 23 PVC
210 White 1494[2] A,F CLD 23 PVC
210 White 271[2] A,F CLD 23 PVC
210A Gray 172[2] A,F CLD 23 PVC
210A White 1271 (HS)[2] A,F CLD 23 PVC
210A White 1279[2] A,F CLD 23 PVC
216A Gray 172[2] A,F CLD 23 PVC
216A White 278[2] A,F CLD 23 PVC
I0210 Green 5133[2] A,F CLD 23 PVC
M1000 Black 2880[2] A,F CLD 23 PVC
M1000 Gray 2700[2] A,F CLD 23 PVC
M1000 White 1114[2] A,F CLD 23 PVC
M1000 White 1240[2] A,F CLD 23 PVC
M1012 White 1244[2] A,F CLD 23 PVC
M1015 Black 2880[2] A,F CLD 23 PVC
M1015 GRAY 2132[2] A,F CLD 23 PVC
M1015 Gray 2709[2] A,F CLD 23 PVC
M1015 WHITE 1235[2] A,F CLD 23 PVC
M1018 White 1424 A,F CLD 23 PVC
M1021 White 1424 A, F CLD 23 PVC
M1022 Orange 7296 A,F CLD 23 PVC
M1030 Gray 2709[2] A,F CLD 23 PVC
M1030 White 1424[2] A,F CLD 23 PVC
M1090 Black 2880 A,F CLD 23 PVC
M1100 Gray 2700 A,F CLD 23 PVC
M1100 White 1240[2] A,F CLD 23 PVC
M1200 White 1240[2] A, F CLD 23 PVC
M1210 Black 2880[2] A, F CLD 23 PVC
M1210 Gray 2306[2] A, F CLD 23 PVC
M1210 Gray 2580[2] A,F CLD 23 PVC
M1210 Gray 2600[2] A,F CLD 23 PVC
M1210 Gray 2700[2] A, F CLD 23 PVC
M1210 Green 5225[2] A, F CLD 23 PVC
M1210 Green 5237[2] A,F CLD 23 PVC
M1210 Light Grey 2863[2] A,F CLD 23 PVC
M1210 Natural 0000[2] A,F CLD 23 PVC
M1210 White 1240[2] A, F CLD 23 PVC
M3000 Gray 2700[2] A,F CLD 23 PVC
M3000 Natural 0000[2] A,F CLD 23 PVC
M3000 White 1240[2] A,F CLD 23 PVC
M3220 Gray 2440[2] A, F CLD 23 PVC
M3220 White 1240[2] A, F CLD 23 PVC
M3700 Black 2975 F CLD 23 PVC
M3700 Natural 0000 F CLD 23 PVC
M3700 White 1260 F CLD 23 PVC
M3700 White 1360 F CLD 23 PVC
M3800 Black 2975 F CLD 23 PVC
M3800 Ivory 3010 F CLD 23 PVC
M3800 Natural 0000 F CLD 23 PVC
M3800 White 1260 F CLD 23 PVC
M5100 White 1231[2] A,F CLD 23 PVC
M5200 Light Brown 3365[2] A,F CLD 23 PVC
MP100 Black 2975 F CLD 23 PVC
MP100 White 1360 F CLD 23 PVC
MP101 White 1360 F CLD 23 PVC
MP250 White 1260 F CLD 23 PVC
MP320 Black 2975 F CLD 23 PVC
MP320 White 1367 F CLD 23 PVC

[1] Material designation may or may not include the designation Geon.  The trade designation
    of the product may or may not be followed by either CU or PL:
    CU - Cube
    PL - Pellet
[2] Maximum surface area to volume ratio is 250 sq. in./L.

NOTE: All Listed products from this facility are NSF Certified, whether or not they bear the
      NSF Mark.


 
Polypipe Italia S.r.l. 
Loc. Pianmercato, 5
16044 Cicagna(GE) 
Italy 
39 01 859 2399
Visit this company's website


Facility : Cicagna(GE), Italy

Mechanical Devices

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Valves
Effast Ball Valves [1] [2] CLD 23 MLTPL
Effast Butterfly Valve Series H [3] CLD 23 MLTPL
Effast Butterfly Valve Series P [3] CLD 23 MLTPL
Effast Check Valves CKD Series [4] CLD 23 MLTPL

[1] Certified for the following products:
    BK1D (Industrial Double Union, Solvent Cement)
      16 mm (BDRBK1D0160)
      20 mm (BDRBK1D0200)
      25 mm (BDRBK1D0250)
      32 mm (BDRBK1D0320)
      40 mm (BDRBK1D0400)
      50 mm (BDRBK1D0500)
      63 mm (BDRBK1D0630)
      75 mm (BDRBK1D0750)
      90 mm (BDRBK1D0900)
      110 mm (BDRBK1D1100)
    BK1E (Industrial Double Union, BSP Threaded)
      3/8" (BERBK1E016A)
      1/2" (BERBK1E020B)
      3/4" (BERBK1E025C)
      1" (BERBK1E032D)
      1 1/4" (BERBK1E040E)
      1 1/2" (BERBK1E050F)
      2" (BERBK1E063G)
      2 1/2" (BERBK1E075H)
      3" (BERBK1E090I)
      4" (BERBK1E110L)
    BK1A (Industrial Double Union, BS)
      3/8" (BARBK1A0160)
      1/2" (BARBK1A0200)
      3/4" (BARBK1A0250)
      1" (BARBK1A0320)
      1 1/4" (BARBK1A0400)
      1 1/2" (BARBK1A0500)
      2" (BARBK1A0630)
      2 1/2" (BARBK1A0750)
      3" (BARBK1A0900)
      4" (BARBKA1100)
    BK1F (Industrial Flanged Double Union, Solvent Cement)
      20 mm (BDRBK1F0200)
      25 mm (BDRBK1F0250)
      32 mm (BDRBK1F0320)
      40 mm (BDRBK1F0400)
      50 mm (BDRBK1F0500)
      63 mm (BDRBK1F0630)
      75 mm (BDRBK1F0750)
      90 mm (BDRBK1F0900)
      110 mm (BDRBK1F1100)
    BXD (Industrial Double Union, Metric)
      16 mm (BDRBXD0160)
      20 mm (BDRBXD0200)
      25 mm (BDRBXD0250)
      32 mm (BDRBXD0320)
      40 mm (BDRBXD0400)
      50 mm (BDRBXD0500)
      63 mm (BDRBXD0630)
      75 mm (BDRBXD0750)
      90 mm (BDRBXD0900)
      110 mm (BDRBXD1100)
    BXE (Industrial Double Union, BSP Threaded)
      3/8" (BERBXE016A)
      1/2" (BERBXE020B)
      3/4" (BERBXE025C)
      1" (BERBXE032D)
      1 1/4" (BERBXE040E)
      1 1/2" (BERBXE050F)
      2" (BERBXE063G)
      2 1/2" (BERBXE075H)
      3" (BERBXE090I)
      4" (BERBXE110L)
    BXA (Industrial Double Union, BS)
      3/8" (BARBXA0160)
      1/2" (BARBXA0200)
      3/4" (BARBXA0250)
      1" (BARBXA0320)
      1 1/4" (BARBXA0400)
      1 1/2" (BARBXA0500)
      2" (BARBXA0630)
      2 1/2” (BARBXA0750)
      3" (BARBXA0900)
      4" (BARBXA1100)
    BXF (Industrial Flanged Double Union, Solvent Cement)
      20 mm (BDRBXF0200)
      25 mm (BDRBXF0250)
      32 mm (BDRBXF0320)
      40 mm (BDRBXF0400)
      50 mm (BDRBXF0500)
      63 mm (BDRBXF0630)
      75 mm (BDRBXF0750)
      90 mm (BDRBXF0900)
      110 mm (BDRBXF1100)
    SXD (Industrial Single Union, Metric)
      20 mm (BDRSXD0200)
      25 mm (BDRSXD0250)
      32 mm (BDRSXD0320)
      40 mm (BDRSXD0400)
      50 mm (BDRSXD0500)
      63 mm (BDRSXD0630)
      75 mm (BDRSXD0750)
      90 mm (BDRSXD0900)
      110 mm (BDRSXD1100)
    SXE (Industrial Single Union, BSP Threaded)
      1/2" (BERSXE020B)
      3/4" (BERSXE025C)
      1" (BERSXE032D)
      1 1/4" (BERSXE040E)
      1 1/2" (BERSXE050F)
      2" (BERSXE063G)
      2 1/2" (BERSXE075H)
      3" (BERSXE090I)
      4" (BERSXE110L)
    BVD (Double Union, Metric Solvent Cement)
      16 mm (BDRBVD0160)
      20 mm (BDRBVD0200)
      25 mm (BDRBVD0250)
      32 mm (BDRBVD0320)
      40 mm (BDRBVD0400)
      50 mm (BDRBVD0500)
      63 mm (BDRBVD0630)
      75 mm (BDRBVD0750)
      90 mm (BDRBVD0900)
      110 mm (BDRBVD1100)
    BVE (Double Union, BSP Threaded)
      3/8" (BERBVE016A)
      1/2" (BERBVE020B)
      3/4" (BERBVE025C)
      1" (BERBVE032D)
      1 1/4" (BERBVE040E)
      1 1/2" (BERBVE050F)
      2" (BERBVE063G)
      2 1/2" (BERBVE075H)
      3" (BERBVE090I)
      4" (BERBVE110L)
    BVA (Double Union, BS Solvent Cement)
      3/8" (BARBVA0160)
      1/2" (BARBVA0200)
      3/4" (BARBVA0250)
      1" (BARBVAA0320)
      1 1/4" (BARBVA0400)
      1 1/2" (BARBVA0500)
      2" (BARBVA0630)
      2 1/2" (BARBVA0750)
      3" (BARBVA0900)
      4" (BARBVA1100)
    BVS (Double Union, ASTM)
      20 mm (BSRBVS0200)
      25 mm (BSRBVS0250)
      32 mm (BSRBVS0320)
      40 mm (BSRBVS0400)
      50 mm (BSRBVS0500)
      63 mm (BSRBVS0630)
      75 mm (BSRBVS0750)
      90 mm (BSRBVS0900)
      110 mm (BSRBVS1100)
    BVN (Double Union, NPT Threaded)
      1/2" (BNRBVN020B)
      3/4" (BNRBVN025C)
      1" (BNRBVN032D)
      1 1/4" (BENBVN040E)
      1 1/2" (BENBVN050F)
      2" (BENBVN063G)
      2 1/2" (BENBVN075H)
      3" (BENBVN090I)
      4" (BENBVN110L)
    BVJ (Double Union, JIS)
      20 mm (BJRBVJ0200)
      25 mm (BJRBVJ0250)
      32 mm (BJRBVJ0320)
      40 mm (BJRBVJ0400)
      50 mm (BJRBVJ0500)
      63 mm (BJRBVJ0630)
      75 mm (BJRBVJ0750)
      90 mm (BJRBVJ0900)
      110 mm (BJRBVJ1100)
[2] SVD (Single Union, Metric)
      20 mm (BDRSVD0200)
      25 mm (BDRSVD0250)
      32 mm (BDRSVD0320)
      40 mm (BDRSVD0400)
      50 mm (BDRSVD0500)
      63 mm (BDRSVD0630)
      75 mm (BDRSVD0750)
      90 mm (BDRSVD0900)
      110 mm (BDRSVD1100)
    SVE (Single Union, BSP, Threaded)
      1/2" (BERSVE020B)
      3/4" (BERSVE025C)
      1" (BERSVE032D)
      1 1/4" (BERSVE040E)
      1 1/2" (BERSVE050F)
      2" (BERSVE063G)
      2 1/2" (BERSVE075H)
      3" (BERSVE090I)
      4" (BERSVE110L)
    SVA (Single Union, BS, Solvent Cement)
      1/2" (BARSVA0200)
      3/4" (BARSVA0250)
      1" (BARSVA0320)
      1 1/4" (BARSVA0400)
      1 1/2" (BARSVA0500)
      2" (BARSVA0630)
      2 1/2" (BARSVA0750)
      3" (BARSVA0900)
      4" (BARSVA1100)
[3] Approved control options include handle, gearbox, electric, and pneumatic.
[4] Certified for the following sizes:
      65 mm (CDRCKD0750)
      80 mm (CDRCKD0900)
      100 mm (CDRCKD1100)
      125 mm (CDRCKD1400)
      150 mm (CDRCKD1600)



 
Polyplastics Co., Ltd. 
18-1, Konan 2-chome, Minato-ku
Tokyo 108-8280 
Japan 
81 3 6711 8605


Facility : Shizuoka-Ken, Japan

Potable Water Materials

    Water Water
    Contact Contact
Trade Designation End Use Temp Material

Potable Water Materials
DURACON® GB-25R WF3500[1] A,F,P C. HOT POM
DURAFIDE® 1130A1 WF2000 A,F C. HOT PPS
DURAFIDE® 1130A1 WF9050 A,F C. HOT PPS
DURAFIDE® 1130T6 WF 9050 A,F C. HOT PPS
DURAFIDE® 1130TX11 WF9100 A,F C. HOT PPS
DURAFIDE® 1140A1 WF2000 A,F C. HOT PPS
DURAFIDE® 1140A1 WF9050 A,F C. HOT PPS
DURAFIDE® 1140A1T HD9001 A,F C. HOT PPS
DURAFIDE® 1140A6 WF2000 A,F C. HOT PPS
DURAFIDE® 1140A6 WF9100 A,F C. HOT PPS

[1] Certified for a maximum surface area to volume ratio of 325 sq. in./L.

NOTE: All products with these designations from this production facility are NSF Certified,
      whether or not they bear the NSF Mark.


Facility : Pahang, Malaysia

Potable Water Materials

    Water Water
    Contact Contact
Trade Designation End Use Temp Material

Potable Water Materials
DURACON® EX-09 WK2001[1] A,F,P C. HOT POM
DURACON® GH-25 WK3500[2] A,F,P C. HOT POM
DURACON® GH-25 WK3501[2] A,F,P C. HOT POM
DURACON® M270-44 WK2001[3] A,F,P C. HOT POM
DURACON® M270-57 WK2001[4] A,F,P C. HOT POM
DURACON® M90-44 WK2001[3] A,F,P C. HOT POM
DURACON® M90-44 WK3068[5] A,F,P C. HOT POM
DURACON® M90-57 WK2001[4] A,F,P C. HOT POM
DURAFIDE® 1130TX2 WK9100 A,F C. HOT PPS
DURAFIDE® 1140A1 WK9050 A,F C. HOT PPS
DURAFIDE® 1140A6 WK2000 F,P C. HOT PPS
DURAFIDE® 6165A6 WK9100 A,F C. HOT PPS

[1] Certified for a maximum surface area to volume ratio of 115 sq. in./L.
[2] Certified for a maximum surface area to volume ratio of 125 sq. in./L.
[3] Certified for a maximum surface area to volume ratio of 280 sq. in./L.
[4] Certified for a maximum surface area to volume ratio of 230 sq. in./L.
[5] Certified for a maximum surface area to volume ratio of 120 sq. in./L.



 
Polyplastics Taiwan Co., Ltd. 
12F, No.137, Sec. 2, Nan-Jing E. Road
Taipei 104 
Taiwan 
886 7 787 3740


Facility : Ta Liao Hsian, Taiwan

Potable Water Materials

    Water Water
    Contact Contact
Trade Designation End Use Temp Material

Potable Water Materials
Tepcon® M270 NAT CF2001[1] A,F,P C. HOT POM
Tepcon® M90 NAT CF2001[1] A,F,P C. HOT POM

[1] Certified for a maximum surface area to volume ratio of 280 sq. in./L.

NOTE: All Listed products from this facility are NSF Certified, whether or not they bear the
      NSF Mark.


 
Polyram Plastic Industry Ltd. 
Ram-On
19205 
Israel 
972 4 6499 555
Visit this company's website


Facility : Ram-On, Israel

Potable Water Materials

    Water Water
    Contact Contact
Trade Designation End Use Temp Material

Potable Water Materials
#PPC705BK11 A,F,P D. HOT PP
#PPC705BK11B A,F,P D. HOT PP
PLUSTEK PB306G6BL151 F CLD 23 RNP
Plustek PA3003G6NT-N A,F,P CLD 23 RNP
Plustek PA310G8BK10[1] A,F,P C. HOT RNP
Plustek PB202G50BK39[2] A,F,P CLD 23 RNP
Plustek PB302G50BK39D[2] A,F,P CLD 23 RNP
Plustek PB302G50BK39P[2] A,F,P CLD 23 RNP
Plustek PB305G33BK37[3] A,F,P CLD 23 RNP
Plustek PB305G33BK43[3] A,F,P CLD 23 RNP
RAMLLOY PNS300PWG6BK10 A,F,P C. HOT OTHER
RAMOFIN PPC705BK11H A,F,P D. HOT PP
RAMOFIN PPH300G6BK11[4] A D. HOT RPP
RAMOFIN PPH301G6NT[4] A D. HOT RPP
RAMOFIN PPH308G8GR28 F CLD 23 RPP
RAMOFIN PPH317G4GR406 F CLD 23 RPP
RAMTON PPS300PWG8BK10 A,F,P C. HOT PPS
RAMTON PPS300PWG8NT A, F, P C. HOT PPS
Ramofin PPC705BK11 A,F,P D. HOT PP
Ramofin PPC705BK11B A,F,P D. HOT PP

[1] Certified for a maximum surface area to volume ratio of 60 sq. in./L.
[2] Certified for a maximum surface area to volume ratio of 170 sq. in/L.
[3] Certified for a maximum surface area to volume ratio of 320 sq. in/L.
[4] Certified for a maximum surface area to volume ratio of 250 sq. in/L.



 
Polysi Technologies, Inc. 
5108 Rex McLeod Drive
Sanford, NC 27330 
United States 
919-775-4989
Visit this company's website


Facility : Sanford, NC

Joining and Sealing Materials

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Lubricants
PST-599 >= 1/2" C. HOT SLC



Polytec Co., Ltd. 
171-5 Garosu-ro, Osong-eup
cheongiu, chungcheongbuk-do 28168 
Korea, Republic of 


Facility : Chungbuk, Republic of Korea

Mechanical Devices

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Ball Valves[1] [G]
POLYTEC PE Ball Valve 1/2" - 16" CLD 23 MLTPL

[1] Only products bearing the NSF Mark on the product, product packaging, and/or
    documentation shipped with the product are Certified.
[G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for
    “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state
    laws and the U.S. Safe Drinking Water Act.

    



 
Polytec, Inc. 
191 Barley Park Lane
P.O. Box 659 
Mooresville, NC 28115 
United States 
704-660-5195
Visit this company's website


Facility : Mooresville, NC

Process Media

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Ion Exchange Media[1] [2] [3] [4]
Titanium Silicate 5 - 50 µm CLD 23 SYN

[1] Approved for use only in NSF approved filter cartridges.
[2] Certified for water treatment plant applications.
[3] This product has not been evaluated for point use applications.
[4] This product is to be flushed once with at least 10 bed volumes of water before placing
    into service.

NOTE: Certified for water treatment plant applications.
      This product has not been evaluated for point of use applications.


 
Polytech Industries LLC 
Rakia Industrial Zone, Wiz-04
WH 25-28, Al Jazira Al Hamra 
Ras Al Khaimah 35892 
United Arab Emirates 
971 7 243 4951
Visit this company's website


Facility : Ras Al Khaimah, United Arab Emirates

Joining and Sealing Materials

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Gasket/Sealing Materials
EPDM Rubber Gasket for Pipe Sealing [1] C. HOT EPDM
PIL/FS [1] C. HOT EPDM
PIL/Sealing Gasket [1] C. HOT EPDM

[1] Certified for a maximum surface area to volume ratio of 2 sq. in./L.

NOTE: Only products bearing the NSF Mark on the product, product packaging, and/or
      documentation shipped with the product are Certified.


 
Polytubes 2009 Inc. 
16221 - 123 Avenue
Edmonton, AB T5V 1N9 
Canada 
780-453-2211
Visit this company's website


Facility : Edmonton, Alberta, Canada

Pipes and Related Products

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Pipe
PT D2100 1/2" - 42" CLD 23 PE
PT D247 1/2" - 42" CLD 23 PE
PT D347 1/2" - 42" CLD 23 PE
PT D47 1/2" - 42" CLD 23 PE
PT-I36 1/2" - 42" CLD 23 PE
PT-I38 1/2" - 42' CLD 23 PE
PT-I47 1/2" - 42" CLD 23 PE



Facility : Peterborough, Ontario, Canada

Pipes and Related Products

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Pipe
PT D2100 1/2" - 42" CLD 23 PE
PT D247 1/2" - 42" CLD 23 PE
PT D347 1/2" - 42" CLD 23 PE
PT D47 1/2" - 42" CLD 23 PE
PT-I36 1/2" - 42" CLD 23 PE
PT-I38 1/2" - 42' CLD 23 PE
PT-I47 1/2" - 42" CLD 23 PE



 
Polyval Coatings Inc. 
520 Curé Boivin
Boisbriand, QC J7G 2A7 
Canada 
800-465-0905 
450-430-6780
Visit this company's website


Facility : Boisbriand, Québec, Canada

Protective (Barrier) Materials

    Water Water
  Water Contact Contact Contact
Trade Designation Size Restriction Temp Material

Coatings - Tank
Polyflex 59PW[1] >= 30,000 gal. CLD 23 PUR
Polyflex PW[2] >= 30,000 gal. CLD 23 PUA

[1] Colors: Blue, white
    Number of Coats: 1-3
    Maximum Field Use Dry Film Thickness (in mils): 25
    Maximum Thinner: 10% DE300	
    Recoat Cure Time and Temperature: 4 hours at 70°F
    Final Cure Time and Temperature: 7 days at 70°F
    Special Comments: Mix ratio of Part A:Part B is 1:2 by volume.
[2] Colors: Beige, blue, or off-white
    Number of Coats: 1-2
    Maximum Field Use Dry Film Thickness (in mils): 100
    Maximum Thinner: None
    Recoat Cure Time and Temperature: 30 minutes at 75°F
    Final Cure Time and Temperature: 24 hours at 75°F
    Special Comments: Mix ratio of Part A to Part B is 1:1 by volume.  Application is by
    plural component gun.



 
Polyvalve LLC, an Andronaco Industries Company 
4855 Broadmoor Avenue Southeast
Kentwood, MI 49512 
United States 
616-656-2260
Visit this company's website


Facility : Kentwood, MI

Mechanical Devices

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Valves[1]
X-69(a)(b)-N(c) Poly-Water® Polyvalve™ 2" - 12" CLD 23 MLTPL
X-69(a)(b)-N(c) Polyvalve II (C-style), Poly-Water® Polyvalve™ 1/2" - 2" CLD 23 MLTPL

[1] X-69(a)(b)-N(c)
    X - Valve size in inches (1/2, 3/4, 1, 1 1/4, 2, 3, 4, 6, 8 or 12)
    6 - Identified valve as a Polyvalve Poly-Water valve for water and wastewater
    9 - Body material DOW DGDA 2490
    a - Defines flow passage (flow or reduced) and end connection (ANSI or Metric dimention)
        1. Full opening    - American iron pipe size ends
        2. Reduced opening - American iron pipe size ends
        3. Full opening    - Metric ends
        4. Reduced opening - Metric ends
        5. Full opening    - CTS ends or other special feature ends
        6. Reduced opening - CTS ends or other special feature ends
    b - Standard Dimension Ratio (9.3, 10, 11, or 13.5)
    N - NSF Potable Water
    c - End configuration
        None - Butt fusion
        -SE  - Socket end



 
Porex Corporation 
500 Bohannon Road
Fairburn, GA 30213 
United States 
800-241-0195 
678-479-1628
Visit this company's website


Facility : Fairburn, GA

Mechanical Devices

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Filter Underdrain[1]
101528 45.31" x 9.56" x3/4" CLD 23 PE
21187 34" x 10.75" x 3/4"" CLD 23 PE
21265 59" x 50.5" x 3/4" CLD 23 PE
41067 34" x 16" x 3/4" CLD 23 PE
41136 8.4" x 8.4" x 3/4" CLD 23 PE
41268 5.7" x 5.7" x 3/4" CLD 23 PE
41449 46.75" x9.75" x3/4"" CLD 23 PE
41603 240" x 10.75" x3/4"" CLD 23 PE
41692 56" x 47.75" x 3/4" CLD 23 PE
41693 56" x 47.75" x 3/4" CLD 23 PE
41896 8.37" x 8.37" x 1/2" CLD 23 PE
41927 45.31" x 9.54" x3/4" CLD 23 PE
42039 38.5" x 7.5" x 1" CLD 23 PE
6080 38.5" x 11.6" x 7/8" CLD 23 PE
6089 38.5" x 11.6" x 7/8" CLD 23 PE
6091 38.5" x 7.5" x 7/8" CLD 23 PE
6115 38.5" x 12" x 7/8" CLD 23 PE
6164 38.5" x 11.6" x 7/8" CLD 23 PE
9082 34" x 16" x 3/4" CLD 23 PE
9083 33" x 16" x 3/4" CLD 23 PE
9742 35" x 10" x 3/4" CLD 23 PE

[1] Certified for a flow rate of 2 gallons per minute per square foot.



 
Powers, a Watts Regulator Co. Division 
815 Chestnut Street
North Andover, MA 01845 
United States 
978-688-1811


Facility : Franklin, NH

Mechanical Devices

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Valves[G]
LFIS075VL 3/4" CLD 23 MLTPL
LFIS100VL 1" C. HOT MLTPL

[G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for
    “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state
    laws and the U.S. Safe Drinking Water Act.

    


Mechanical Plumbing Devices

Trade Designation      

Faucets[1] [G]
0215-6      
105      
115      
205      
215      

[1] Suffixes:
    -6  - 6" Handle (4" is the default size)
    A15 - Aerator flow rate is 1.5 GPM
    A5  - Aerator flow rate is 0.5 GPM (default flow rate is 2.0 GPM)
    GD  - Grid drain
    L   - Laminar flow outlet 
    L5  - 0.5 gpm laminar flow outlet 
    OGD - Offset grid drain
    PW  - Faucet has pop-up waste stopper
    VA  - Vandal-resistant aerator 
    V5  – Vandal-resistant 0.5 gpm aerator 
    VL  - Vandal-resistant laminar flow outlet 
    VL5 - Vandal-resistant 0.5 gpm laminar flow outlet
[G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for
    “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state
    laws and the U.S. Safe Drinking Water Act.

    

Miscellaneous Faucet Components[G]
SA-205XA1 Gooseneck Assembly      

[G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for
    “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state
    laws and the U.S. Safe Drinking Water Act.

    

Valves and Related Fittings[2] [G]
LFG480-00      
LFG480-01      
LFG480-10      
LFG480-11      
LFG480-50      
LFG480-51      
LFP580-4      
LFe480-00      
LFe480-01      
LFe480-10      
LFe480-11      
LFe480-50      
LFe480-51      

[2] LF - Indicates Fead Free construction		
    e  - 0.5 gpm minimum flow		
    G  - 0.25 gpm minimum flow		
    Suffixes:		
    00 - 1/2" NPT rough Bronze finish		
    01 - 1/2" NPT chrome plated finish		
    10 - 3/8" Compression rough Bronze finish		
    11 - 3/8" Compression chrome plated finish		
    50 - 3/8" Quick-Connect rough Bronze finish		
    51 - 3/8" Quick-Connect chrome plated finish		
    		
    Trade names may also have a suffix of QC for Quick Connect or SC for Satin Chrome.		
[G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for
    “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state
    laws and the U.S. Safe Drinking Water Act.

    



Facility : St Pauls, NC

Mechanical Devices

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Valves[G]
LFIS150 (81020206) 1 1/2" C. HOT MLTPL
LFIS200 (81020207) 2" C. HOT MLTPL

[G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for
    “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state
    laws and the U.S. Safe Drinking Water Act.

    



 
PPG Coatings (Kunshan) Co., Ltd. 
53 Jinyang Road Lujia Town
Kunshan Jiangsu Province 215331 
China 
886 512 57678859


Facility : Jiangsu Province, China

Protective (Barrier) Materials

    Water Water
  Water Contact Contact Contact
Trade Designation Size Restriction Temp Material

Coatings - Valve
AmerLock 400[1] [2] >= 100 mm CLD 23 EPOXY

[1] Colors: Black, oxide red, sky blue
    Number of Coats: 1
    Maximum Field Use Dry Film Thickness (in mils): 8 
    Maximum Thinner: 20% Thinner 21-06
    Final Cure Time and Temperature: 7 days at ambient temperature
    Special Comments: Mix ratio is of base to hardener is 1:1 by volume
[2] Certification does not include Accelerator 861.



 
PPG Coatings Europe B.V. 
P.O. Box 58034
1040 HA Amsterdam 
The Netherlands 
31 20 407 5050
Visit this company's website


Facility : Deurne, Belgium

Protective (Barrier) Materials

    Water Water
  Water Contact Contact Contact
Trade Designation Size Restriction Temp Material

Coatings - Pipe[1]
PhenGuard 965[2] >= 92 cm CLD 23 EPOXY
Phenguard 930/940[3] >= 60" CLD 23 EPOXY
Sigmaguard CSF 585[4] >= 20 cm CLD 23 EPOXY
Sigmaguard CSF 585 US[4] >= 20 cm CLD 23 EPOXY
Sigmaguard CSF 85[4] >= 20 cm CLD 23 EPOXY

[1] Only products bearing the NSF Mark on the product, product packaging, and/or
    documentation shipped with the product are Certified.
[2] Number of Coats: 3
    Sequence of Coats: 965 White, 965 Pink, 965 Grey
    Maximum Field Use Dry Film Thickness (in mils): 12 (4 per coat)
    Maximum Thinner: 5% Thinner 91-92
    Recoat Cure Time and Temperature: 7 days at 25°C
    Final Cure Time and Temperature: 14 days at 25°C
    Special Comments: Mix ratio of Part A:Part B is 87:13 by volume or 92.1:7.9 by weight.
    Induction time is 15 minutes. Apply 6 wet mils to achieve 4 dry mils.
[3] Colors: Light grey, Off white
    Number of Coats: 2	
    Sequence of Coats: 930 Off White, 940 Grey
    Maximum Field Use Dry Film Thickness (in mils): 12 (6 per coat); 18 wet (9 wet per coat)
    Maximum Thinner: 5% 91-92 Thinner
    Recoat Cure Time and Temperature: 7 days at 25°C
    Final Cure Time and Temperature: 14 days at 25°C
    Special Comments: Mix ratio by volume of Part A:Part B is 88:12.  Induction period is 15
    minutes.
[4] Colors:  Blue 1000, White 7000
    Number of Coats:  1
    Maximum Field Use Dry Film Thickness (in mils):  15
    Maximum Thinner:  None
    Final Cure:  12 days @ 20°C
    Special Comments:  Mix ratio of A:B is 77.5:22.5 by volume.

Coatings - Tank[1]
PhenGuard 965[2] >= 2000 gal. CLD 23 EPOXY
Phenguard 930/940[3] >= 6000 gal. CLD 23 EPOXY
Sigmaguard CSF 585[4] >= 100 gal. CLD 23 EPOXY
Sigmaguard CSF 585 US[4] >= 100 gal. CLD 23 EPOXY
Sigmaguard CSF 85[4] >= 100 gal. CLD 23 EPOXY

[1] Only products bearing the NSF Mark on the product, product packaging, and/or
    documentation shipped with the product are Certified.
[2] Number of Coats: 3
    Sequence of Coats: 965 White, 965 Pink, 965 Grey
    Maximum Field Use Dry Film Thickness (in mils): 12 (4 per coat)
    Maximum Thinner: 5% Thinner 91-92
    Recoat Cure Time and Temperature: 7 days at 25°C
    Final Cure Time and Temperature: 14 days at 25°C
    Special Comments: Mix ratio of Part A:Part B is 87:13 by volume or 92.1:7.9 by weight.
    Induction time is 15 minutes. Apply 6 wet mils to achieve 4 dry mils.
[3] Colors: Light grey, Off white
    Number of Coats: 2	
    Sequence of Coats: 930 Off White, 940 Grey
    Maximum Field Use Dry Film Thickness (in mils): 12 (6 per coat); 18 wet (9 wet per coat)
    Maximum Thinner: 5% 91-92 Thinner
    Recoat Cure Time and Temperature: 7 days at 25°C
    Final Cure Time and Temperature: 14 days at 25°C
    Special Comments: Mix ratio by volume of Part A:Part B is 88:12.  Induction period is 15
    minutes.
[4] Colors:  Blue 1000, White 7000
    Number of Coats:  1
    Maximum Field Use Dry Film Thickness (in mils):  15
    Maximum Thinner:  None
    Final Cure:  12 days @ 20°C
    Special Comments:  Mix ratio of A:B is 77.5:22.5 by volume.



Facility : Nam-gu, Korea, Republic of

Protective (Barrier) Materials

    Water Water
  Water Contact Contact Contact
Trade Designation Size Restriction Temp Material

Coatings - Tank
SigmaGuard CSF 650[2] >= 2000 gal. CLD 23 EPOXY
SigmaGuard CSF 650[1] >= 500 mm CLD 23 EPOXY

[1] Colors: White
    Number of coats: 1
    Maximum field use dry film thickness (in mils): 16 mils (For Pipe End Use)
    Maximum thinner: None
    Final cure time and temperature: 30 days @ 23°C (Pipe end use only)
    Special comments: For Pipe End Use only: Mix ratio of Part A to Part B is 80:20 by
    volume. No induction period.
[2] Colors: Green, white
    Number of Coats: 1
    Maximum Field Use Dry Film Thickness (in mils): 12
    Maximum Thinner: None
    Final Cure Time and Temperature: 5 days at 20ºC
    Special Comments: Mix ratio of Part A to Part B is 80:20 by volume. No induction period.
    Once cure is complete, fill
    tank with fresh tap water and allow to soak for 4 days. After soaking in water for 4
    days, rinse with high pressure water and drain tank.

NOTE: Only products bearing the NSF Mark on the product, product packaging, and/or
      documentation shipped with the product are Certified.


 
PPG Industries, Inc. 
One PPG Place
Pittsburgh, PA 15272 
United States 
412-434-3131


Facility : Brazil, IN

Protective (Barrier) Materials

    Water Water
  Water Contact Contact Contact
Trade Designation Size Restriction Temp Material

Coatings - Fittings
B13369ER80K[1] >= 2" CLD 23 PEC
B14062EB90K[1] >= 2" CLD 23 PEC
PCMT80109 White Epoxy[2] >= 2" CLD 23 PEC

[1] Number of Coats: 1
    Maximum Field Use Dry Film Thickness (in mils): 20
    Final Cure Time and Temperature: 20 minutes at 375°F
[2] Color: White
    Number of Coats: 1-2
    Maximum Field Use Dry Film Thickness (in mils): 40
    Final Cure Time and Temperature: 10 minutes at 320°F

Coatings - Pipe
B10889EB90K-C[3] >= 0.84" C. HOT PEC
B10889EB90K-I[3] >= 0.84" C. HOT PEC
B10889EB90K-J[3] >= 0.84" C. HOT PEC
PCMT80109 White Epoxy[2] >= 1" CLD 23 PEC
Smith Blair Blue Epoxy[3] >= 0.84" C. HOT PEC

[2] Color: White
    Number of Coats: 1-2
    Maximum Field Use Dry Film Thickness (in mils): 40
    Final Cure Time and Temperature: 10 minutes at 320°F
[3] Color: Blue
    Number of Coats: 1
    Maximum Field Use Dry Film Thickness (in mils): 60
    Final Cure Time and Temperature: 15 minutes at 380°F

Coatings - Tank
PCMT80109 White Epoxy[2] >= 50 gal. CLD 23 PEC

[2] Color: White
    Number of Coats: 1-2
    Maximum Field Use Dry Film Thickness (in mils): 40
    Final Cure Time and Temperature: 10 minutes at 320°F

Coatings - Valve
B13369ER80K[1] >= 2" CLD 23 PEC
B14062EB90K[1] >= 2" CLD 23 PEC
PCMT80109 White Epoxy[2] >= 2" CLD 23 PEC

[1] Number of Coats: 1
    Maximum Field Use Dry Film Thickness (in mils): 20
    Final Cure Time and Temperature: 20 minutes at 375°F
[2] Color: White
    Number of Coats: 1-2
    Maximum Field Use Dry Film Thickness (in mils): 40
    Final Cure Time and Temperature: 10 minutes at 320°F



 
PPG Protective and Marine Coatings 
11605 Vimy Ridge Road
Alexander, AR 72002 
United States 
501-235-9148


Facility : # 2 USA

Protective (Barrier) Materials

    Water Water
  Water Contact Contact Contact
Trade Designation Size Restriction Temp Material

Coatings - Fittings
95-172/95-178 Aquapon® Low Temperature Potable Water Epoxy Coating Ind. White[1] >= 1 1/2" CLD 23 EPOXY

[1] Colors: Industrial White, industrial gray
    Number of Coats: 2-4
    Sequence of Coats: Any combination
    Maximum Field Use Dry Film Thickness (in mils): 18 (7 per coat maximum)
    Maximum Thinner: 10 oz/gal or 8%
    Recoat Cure Time and Temperature: 3 hours at 77°F
    Final Cure Time and Temperature: 7 days at 77°F
    Special Comments: Mix ratio of A:B is 1:1 by volume.

Coatings - Pipe
95-172/95-178 Aquapon® Low Temperature Potable Water Epoxy Coating Ind. White[1] >= 16" CLD 23 EPOXY
95-172/95-178 Aquapon® Low Temperature Potable Water Epoxy Coating Ind. Gray[1] >= 16" CLD 23 EPOXY

[1] Colors: Industrial White, industrial gray
    Number of Coats: 2-4
    Sequence of Coats: Any combination
    Maximum Field Use Dry Film Thickness (in mils): 18 (7 per coat maximum)
    Maximum Thinner: 10 oz/gal or 8%
    Recoat Cure Time and Temperature: 3 hours at 77°F
    Final Cure Time and Temperature: 7 days at 77°F
    Special Comments: Mix ratio of A:B is 1:1 by volume.

Coatings - Valve
95-172/95-178 Aquapon® Low Temperature Potable Water Epoxy Coating Ind. White[1] >= 4" CLD 23 EPOXY
95-172/95-178 Aquapon® Low Temperature Potable Water Epoxy Coating Ind. Gray[1] >= 4" CLD 23 EPOXY

[1] Colors: Industrial White, industrial gray
    Number of Coats: 2-4
    Sequence of Coats: Any combination
    Maximum Field Use Dry Film Thickness (in mils): 18 (7 per coat maximum)
    Maximum Thinner: 10 oz/gal or 8%
    Recoat Cure Time and Temperature: 3 hours at 77°F
    Final Cure Time and Temperature: 7 days at 77°F
    Special Comments: Mix ratio of A:B is 1:1 by volume.

Coatings - Fittings
95-172/95-178 Aquapon® Low Temperature Potable Water Epoxy Coating Ind. Gray[1] >= 1 1/2" CLD 23 EPOXY

[1] Colors: Industrial White, industrial gray
    Number of Coats: 2-4
    Sequence of Coats: Any combination
    Maximum Field Use Dry Film Thickness (in mils): 18 (7 per coat maximum)
    Maximum Thinner: 10 oz/gal or 8%
    Recoat Cure Time and Temperature: 3 hours at 77°F
    Final Cure Time and Temperature: 7 days at 77°F
    Special Comments: Mix ratio of A:B is 1:1 by volume.

Coatings - Tank
95-172/95-178 Aquapon® Low Temperature Potable Water Epoxy Coating Ind. White[1] >= 1,000 gal. CLD 23 EPOXY
95-172/95-178 Aquapon® Low Temperature Potable Water Epoxy Coating Ind. Gray[1] >= 1,000 gal CLD 23 EPOXY

[1] Colors: Industrial White, industrial gray
    Number of Coats: 2-4
    Sequence of Coats: Any combination
    Maximum Field Use Dry Film Thickness (in mils): 18 (7 per coat maximum)
    Maximum Thinner: 10 oz/gal or 8%
    Recoat Cure Time and Temperature: 3 hours at 77°F
    Final Cure Time and Temperature: 7 days at 77°F
    Special Comments: Mix ratio of A:B is 1:1 by volume.



Facility : Alexander, AR

Protective (Barrier) Materials

    Water Water
  Water Contact Contact Contact
Trade Designation Size Restriction Temp Material

Coatings - Fittings
Amercoat 133[1] >= 4" CLD 23 EPOXY
Amercoat 133/Amercoat 333[2] >= 4" CLD 23 EPOXY

[1] Colors: Oxide red, white
    Number of Coats: 1-2
    Maximum Field Use Dry Film Thickness (in mils): 6 per coat; 10 total
    Recoat Cure Time and Temperature: 24 hours at 75°F
    Final Cure and Temperature: 14 days at 75°F
    Special Comments: Mix ratio of resin to cure is 4:1 by volume. Mix for 5 minutes, let
    stand for 10 minutes, then remix for 2-3 minutes before application. Scrape the sides of
    the can while mixing.
[2] Colors: Primer: Tank Primer Green, white; Topcoat: Buff, IM gray, off-white, tank pale
    blue
    Number of Coats: 2
    Sequence of Coats: 1. Amercoat 133 (primer) 2. Amercoat 333 (topcoat)
    Maximum Field Use Dry Film Thickness (in mils): 133: 4-8 per coat 333: 10-12 per coat;
    20 total for 133/333 system.
    Recoat Cure Time and Temperature: 24 hours at 75°F
    Final Cure Time and Temperature: 14 days at 75°F
    Special Comments: The mix ratio is 22 parts base to 3 parts cure by weight. Mix for 5
    minutes, let stand for 10 minutes, then remix for 2-3 minutes before application. Scrape
    the sides of the can while mixing.

Coatings - Pipe
Amercoat 133[1] >= 30" CLD 23 EPOXY
Amercoat 133/Amercoat 333[2] >= 12" CLD 23 EPOXY
Amerlock 2[3] >= 48" CLD 23 EPOXY
Novaguard 810[4] [5] CLD 23 EPOXY
Novaguard 810ER[4] [5] CLD 23 EPOXY
Novaguard 840[13] >= 36" CLD 23 EPOXY
Novaguard 840 Filler[14] [15] CLD 23 EPOXY

[1] Colors: Oxide red, white
    Number of Coats: 1-2
    Maximum Field Use Dry Film Thickness (in mils): 6 per coat; 10 total
    Recoat Cure Time and Temperature: 24 hours at 75°F
    Final Cure and Temperature: 14 days at 75°F
    Special Comments: Mix ratio of resin to cure is 4:1 by volume. Mix for 5 minutes, let
    stand for 10 minutes, then remix for 2-3 minutes before application. Scrape the sides of
    the can while mixing.
[2] Colors: Primer: Tank Primer Green, white; Topcoat: Buff, IM gray, off-white, tank pale
    blue
    Number of Coats: 2
    Sequence of Coats: 1. Amercoat 133 (primer) 2. Amercoat 333 (topcoat)
    Maximum Field Use Dry Film Thickness (in mils): 133: 4-8 per coat 333: 10-12 per coat;
    20 total for 133/333 system.
    Recoat Cure Time and Temperature: 24 hours at 75°F
    Final Cure Time and Temperature: 14 days at 75°F
    Special Comments: The mix ratio is 22 parts base to 3 parts cure by weight. Mix for 5
    minutes, let stand for 10 minutes, then remix for 2-3 minutes before application. Scrape
    the sides of the can while mixing.
[3] Colors:  Ivory, medium gray, oxide red, RT 1805 blue, white
    Number of Coats:  2-4
    Sequence of Coats:  Any combination of Listed colors
    Maximum Field Use Dry Film Thickness (in mils): 8 per coat; 18 total
    Maximum Thinner:  12% Amercoat #65 by volume; 12% Amercoat #8 by volume (alternate)
    Recoat Cure Time and Temperature:  24 hours at 72ºF
    Final Cure Time and Temperature: 10 days at 72°F for all end uses except tank >= 250,000
    gallons which has a final cure of 7 days at 72ºF
    Special Comments: Use of Amercoat #8 thinner is limited to tanks of 250,000 gallons of
    greater.Mix ratio of base:cure is 1:1 by volume or 1.1:1 by weight.
[4] Number of Coats: 1-2
    Maximum Field Use Dry Film Thickness (in mils): 30
    Recoat Cure Time and Temperature: 24 hours at 70°F
    Final Cure Time and Temperature: 72 hours at 77°F (Tanks >= 500 gal., Pipe >= 22", Valve
    >=2"), 10 days at 40°F (Tanks >= 250,000 gal., Valve >=1/2")
    Special Comments: Mix ratio of base to hardener (Part A:Part B) is 4:1 by volume.
[5] Certified for tanks >= 500 gallons, pipe >=22", and valves >=2" with a final cure of 72
    hours @ 77º F and tanks >= 250,000 gallons and valves >=1/2" with a final cure of 10
    days at 40º F.
[13] Colors: Cream, Green
     Number of Coats:  1-2
     Maximum field use dry film thickness (in mils): 30
     Recoat cure time and temperature: 24 hours at 70°F
     Final cure time and temperature: 72 hours at 70°F
     Special Comments: Mix ratio of base to hardener is 4:1 by volume
     
[14] Colors: Cream, Green
     Number of Coats: 1
     Maximum field use dry film thickness (in mils): 80
     Final cure time and temperature: 72 hours at 70°F
     Special Comments:  Novaguard 840: Mix ratio of base to hardener is 4:1 by volume.  Mix
     for 5 minutes, let stand for 10 minutes, then remix for 2-3 minutes before application. 
     Scrape the sides of the can while mixing.  After mixing Novaguard 840, add Amercoat 884
     up to 1 pound per gallon."					
     					
     					
     					
     
     
[15] Certified for a maximum of 25% of the surface area of a 500 gallon tank and greater and
     12" pipe and greater.

Coatings - Pump
Amerlock 2[3] >= 4" CLD 23 EPOXY

[3] Colors:  Ivory, medium gray, oxide red, RT 1805 blue, white
    Number of Coats:  2-4
    Sequence of Coats:  Any combination of Listed colors
    Maximum Field Use Dry Film Thickness (in mils): 8 per coat; 18 total
    Maximum Thinner:  12% Amercoat #65 by volume; 12% Amercoat #8 by volume (alternate)
    Recoat Cure Time and Temperature:  24 hours at 72ºF
    Final Cure Time and Temperature: 10 days at 72°F for all end uses except tank >= 250,000
    gallons which has a final cure of 7 days at 72ºF
    Special Comments: Use of Amercoat #8 thinner is limited to tanks of 250,000 gallons of
    greater.Mix ratio of base:cure is 1:1 by volume or 1.1:1 by weight.

Coatings - Tank
Novaguard 840 Filler[14] [15] CLD 23 EPOXY
Amercoat 133[1] >= 50 gal. CLD 23 EPOXY
Amercoat 133/Amercoat 333[2] >= 500 gal. CLD 23 EPOXY
Amercoat 133 + 884 Additive[6] [7] CLD 23 EPOXY
Amerlock 2[3] >= 2000 gal. CLD 23 EPOXY
Amercoat 68HS[8] >= 50,000 gal CLD 23 EPOXY
Amercoat 68PW[8] >= 50,000 gal CLD 23 EPOXY
Novaguard 810[4] [5] CLD 23 EPOXY
Novaguard 810ER[4] [5] CLD 23 EPOXY
Novaguard 840[13] >= 1500 gal. CLD 23 EPOXY

[1] Colors: Oxide red, white
    Number of Coats: 1-2
    Maximum Field Use Dry Film Thickness (in mils): 6 per coat; 10 total
    Recoat Cure Time and Temperature: 24 hours at 75°F
    Final Cure and Temperature: 14 days at 75°F
    Special Comments: Mix ratio of resin to cure is 4:1 by volume. Mix for 5 minutes, let
    stand for 10 minutes, then remix for 2-3 minutes before application. Scrape the sides of
    the can while mixing.
[2] Colors: Primer: Tank Primer Green, white; Topcoat: Buff, IM gray, off-white, tank pale
    blue
    Number of Coats: 2
    Sequence of Coats: 1. Amercoat 133 (primer) 2. Amercoat 333 (topcoat)
    Maximum Field Use Dry Film Thickness (in mils): 133: 4-8 per coat 333: 10-12 per coat;
    20 total for 133/333 system.
    Recoat Cure Time and Temperature: 24 hours at 75°F
    Final Cure Time and Temperature: 14 days at 75°F
    Special Comments: The mix ratio is 22 parts base to 3 parts cure by weight. Mix for 5
    minutes, let stand for 10 minutes, then remix for 2-3 minutes before application. Scrape
    the sides of the can while mixing.
[3] Colors:  Ivory, medium gray, oxide red, RT 1805 blue, white
    Number of Coats:  2-4
    Sequence of Coats:  Any combination of Listed colors
    Maximum Field Use Dry Film Thickness (in mils): 8 per coat; 18 total
    Maximum Thinner:  12% Amercoat #65 by volume; 12% Amercoat #8 by volume (alternate)
    Recoat Cure Time and Temperature:  24 hours at 72ºF
    Final Cure Time and Temperature: 10 days at 72°F for all end uses except tank >= 250,000
    gallons which has a final cure of 7 days at 72ºF
    Special Comments: Use of Amercoat #8 thinner is limited to tanks of 250,000 gallons of
    greater.Mix ratio of base:cure is 1:1 by volume or 1.1:1 by weight.
[4] Number of Coats: 1-2
    Maximum Field Use Dry Film Thickness (in mils): 30
    Recoat Cure Time and Temperature: 24 hours at 70°F
    Final Cure Time and Temperature: 72 hours at 77°F (Tanks >= 500 gal., Pipe >= 22", Valve
    >=2"), 10 days at 40°F (Tanks >= 250,000 gal., Valve >=1/2")
    Special Comments: Mix ratio of base to hardener (Part A:Part B) is 4:1 by volume.
[5] Certified for tanks >= 500 gallons, pipe >=22", and valves >=2" with a final cure of 72
    hours @ 77º F and tanks >= 250,000 gallons and valves >=1/2" with a final cure of 10
    days at 40º F.
[6] Number of Coats: 1
    Maximum Field Use Dry Film Thickness (in mils): 10 dry film thickness in a skim coat
    over pitted steel
    Maximum Thinner: None
    Final Cure Time and Temperature: 7 days at 70ºF (>=250,000 gallon tank), 10 days at 70ºF
    (< 250,000 gallons)
    Special Comments: Amercoat 133: Mix ratio of resin to cure is 4:1 by volume. Mix for 5
    minutes, let stand for 10 minutes, then remix for 2-3 minutes before application. Scrape
    the sides of the can while mixing. After mixing Amercoat 133, add Amercoat 884 at up to
    0.5 lb. per gallon.
[7] Certified for a maximum of 10% of the surface area of a 500 gallon tank.
[8] Colors: Reddish Gray, Green
    Number of coats: 1
    Sequence of coats: Primer
    Maximum field use dry film thickness: 4 mils
    Maximum thinner: 6% Amercoat 65
    Final Cure Time and temperature: 8 hours at 75°F
    Special comments: Mix ratio is 3.02:1.00:13.01 (Part A:PartB:Powder) by weight. Any
    certified PPG top coat may be used provided both primer and top
    coat meet their individual Certified end uses.
[13] Colors: Cream, Green
     Number of Coats:  1-2
     Maximum field use dry film thickness (in mils): 30
     Recoat cure time and temperature: 24 hours at 70°F
     Final cure time and temperature: 72 hours at 70°F
     Special Comments: Mix ratio of base to hardener is 4:1 by volume
     
[14] Colors: Cream, Green
     Number of Coats: 1
     Maximum field use dry film thickness (in mils): 80
     Final cure time and temperature: 72 hours at 70°F
     Special Comments:  Novaguard 840: Mix ratio of base to hardener is 4:1 by volume.  Mix
     for 5 minutes, let stand for 10 minutes, then remix for 2-3 minutes before application. 
     Scrape the sides of the can while mixing.  After mixing Novaguard 840, add Amercoat 884
     up to 1 pound per gallon."					
     					
     					
     					
     
     
[15] Certified for a maximum of 25% of the surface area of a 500 gallon tank and greater and
     12" pipe and greater.

Coatings - Valve
Amercoat 133[1] >= 4" CLD 23 EPOXY
Amercoat 133/Amercoat 333[2] >= 4" CLD 23 EPOXY
Amerlock 2[3] >= 6" CLD 23 EPOXY
Amercoat 370[9] >= 4" CLD 23 EPOXY
Amerlock 400[10] >= 6" CLD 23 EPOXY
Novaguard 810[4] [5] CLD 23 EPOXY
Novaguard 810ER[4] [5] CLD 23 EPOXY
Novaguard 840[13] >= 4" CLD 23 EPOXY

[1] Colors: Oxide red, white
    Number of Coats: 1-2
    Maximum Field Use Dry Film Thickness (in mils): 6 per coat; 10 total
    Recoat Cure Time and Temperature: 24 hours at 75°F
    Final Cure and Temperature: 14 days at 75°F
    Special Comments: Mix ratio of resin to cure is 4:1 by volume. Mix for 5 minutes, let
    stand for 10 minutes, then remix for 2-3 minutes before application. Scrape the sides of
    the can while mixing.
[2] Colors: Primer: Tank Primer Green, white; Topcoat: Buff, IM gray, off-white, tank pale
    blue
    Number of Coats: 2
    Sequence of Coats: 1. Amercoat 133 (primer) 2. Amercoat 333 (topcoat)
    Maximum Field Use Dry Film Thickness (in mils): 133: 4-8 per coat 333: 10-12 per coat;
    20 total for 133/333 system.
    Recoat Cure Time and Temperature: 24 hours at 75°F
    Final Cure Time and Temperature: 14 days at 75°F
    Special Comments: The mix ratio is 22 parts base to 3 parts cure by weight. Mix for 5
    minutes, let stand for 10 minutes, then remix for 2-3 minutes before application. Scrape
    the sides of the can while mixing.
[3] Colors:  Ivory, medium gray, oxide red, RT 1805 blue, white
    Number of Coats:  2-4
    Sequence of Coats:  Any combination of Listed colors
    Maximum Field Use Dry Film Thickness (in mils): 8 per coat; 18 total
    Maximum Thinner:  12% Amercoat #65 by volume; 12% Amercoat #8 by volume (alternate)
    Recoat Cure Time and Temperature:  24 hours at 72ºF
    Final Cure Time and Temperature: 10 days at 72°F for all end uses except tank >= 250,000
    gallons which has a final cure of 7 days at 72ºF
    Special Comments: Use of Amercoat #8 thinner is limited to tanks of 250,000 gallons of
    greater.Mix ratio of base:cure is 1:1 by volume or 1.1:1 by weight.
[4] Number of Coats: 1-2
    Maximum Field Use Dry Film Thickness (in mils): 30
    Recoat Cure Time and Temperature: 24 hours at 70°F
    Final Cure Time and Temperature: 72 hours at 77°F (Tanks >= 500 gal., Pipe >= 22", Valve
    >=2"), 10 days at 40°F (Tanks >= 250,000 gal., Valve >=1/2")
    Special Comments: Mix ratio of base to hardener (Part A:Part B) is 4:1 by volume.
[5] Certified for tanks >= 500 gallons, pipe >=22", and valves >=2" with a final cure of 72
    hours @ 77º F and tanks >= 250,000 gallons and valves >=1/2" with a final cure of 10
    days at 40º F.
[9] Colors: Black, light buff, oxide red, milliken blue, white
    Number of Coats: 2-4
    Maximum Field Use Dry Film Thickness (in mils): 24
    Maximum Thinner: 12.5% Amercoat #65 Thinner
    Recoat Cure Time and Temperature: 0.5 hours at 23°C
    Final Cure Time and Temperature: 7 days at 23°C
    Special Comments: Mix ratio of base:cure is 4:1 by volume.
[10] Colors: Ivory, medium gray, oxide red, RT-1805, white
     Number of Coats: 2-4
     Sequence of Coats: Any combination of Listed colors
     Maximum Field Use Dry Film Thickness (in mils): 6 per coat; 18 total
     Maximum Thinner: 12.5% Amercoat #65 by volume
     Recoat Cure Time and Temperature: 24 hours at 75°F
     Final Cure Time and Temperature: 7 days at 75°F
     Special Comments: Mix ratio of base:cure is 1:1 by volume.
[13] Colors: Cream, Green
     Number of Coats:  1-2
     Maximum field use dry film thickness (in mils): 30
     Recoat cure time and temperature: 24 hours at 70°F
     Final cure time and temperature: 72 hours at 70°F
     Special Comments: Mix ratio of base to hardener is 4:1 by volume
     

Primers[11] [12]
Sigmaweld 199 US >= 900 gal. CLD 23 ZINC

[11] This primer may be used with any Certified PPG topcoat provided both primer and topcoat
     meet their individual Certified end uses.
[12] Colors: Green
     Number of Coats: 1
     Maximum Field Use Dry Film Thickness (in mils): 1 
     Maximum Thinner: None
     Recoat Cure Time and Temperature: Not Applicable
     Final Cure Time and Temperature: Primer (cure before application of topcoat) - 7 days at
     ambient temperature (20°C)
     Special Comments: Mix ratio of binder:paste is 2:1 by volume. Apply to steel substrate.



Facility : Waller, TX

Protective (Barrier) Materials

    Water Water
  Water Contact Contact Contact
Trade Designation Size Restriction Temp Material

Coatings - Pipe[1] [2]
Amerlock® 2/400 VOC >= 36" CLD 23 EPOXY

[1] Colors: Pearl Gray, White and Buff
    Number of Coats: 2-3
    Maximum Field Use Dry Thickness: 18 mil (4-6 mils per coat)
    Maximum Thinner: 7.5% PPG 97-739
    Recoat Cure Time/Temperature: 24 hours at 70F
    Final Cure Time/Temperature: 7 days at 70F
    Special Comments: Mix ratio of Base:Cure is 1:1 by volume. Induction period is 12
    minutes.
[2] Only products bearing the NSF Mark on the product, product packaging, and/or
    documentation shipped with the product are Certified.

Coatings - Tank[1] [2]
Amerlock® 2/400 VOC >= 50,000 gal. CLD 23 EPOXY

[1] Colors: Pearl Gray, White and Buff
    Number of Coats: 2-3
    Maximum Field Use Dry Thickness: 18 mil (4-6 mils per coat)
    Maximum Thinner: 7.5% PPG 97-739
    Recoat Cure Time/Temperature: 24 hours at 70F
    Final Cure Time/Temperature: 7 days at 70F
    Special Comments: Mix ratio of Base:Cure is 1:1 by volume. Induction period is 12
    minutes.
[2] Only products bearing the NSF Mark on the product, product packaging, and/or
    documentation shipped with the product are Certified.



 
PPI America Inc. 
444 North Michigan Avenue
Suite #1200 
Chicago, IL 60611 
United States 
847-430-4477
Visit this company's website


Facility : # 1 Korea

Joining and Sealing Materials

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Gasket/Sealing Materials
PVC Water Pipe Gasket [1] CLD 23 EPDM
Pyungwha PVC Pipe Gasket [1] CLD 23 EPDM

[1] Certified for pipe gasket sizes 50 mm - 400 mm (4" - 16").


Pipes and Related Products

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Pipe
PVC Water pipe 4" - 16" CLD 23 MLTPL
PVC Water pipe [1] CLD 23 PVC
Pyungwha PVC Pipe 4" - 16" CLD 23 MLTPL
Pyungwha PVC Pipe [1] CLD 23 PVC
iPVC water pipe 4" - 16" CLD 23 MLTPL
iPVC water pipe [1] CLD 23 PVC

[1] Straight pipe is available in sizes 16 mm - 400 mm or 1/8" - 16".



 
PPI Pyungwha Co., Ltd. 
1085-11, Beodeul-ro, Jangan-myeon
Hwaseong-si, Gyeonggi-do 445-941 
Korea, Republic of 
82 31 359 0082
Visit this company's website


Facility : # 1 Gyeonggi-do, Republic of Korea

Joining and Sealing Materials

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Gasket/Sealing Materials
PVC Water Pipe Gasket [1] CLD 23 EPDM
Pyungwha PVC Pipe Gasket [1] CLD 23 EPDM

[1] Certified for pipe gasket sizes 50 mm - 400 mm (4" - 16").


Pipes and Related Products

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Pipe
iPVC Water Pipe [1] CLD 23 PVC
PVC Water Pipe [1] CLD 23 PVC
Pyungwha PVC Pipe [1] CLD 23 PVC
iPVC Water Pipe 4" - 16" CLD 23 MLTPL
PVC Water Pipe 4" - 16" CLD 23 MLTPL
Pyungwha PVC Pipe 4" - 16" CLD 23 MLTPL

[1] Straight pipe is available in sizes 16 mm - 400 mm or 1/8" - 16".



 
Prabhat Elastomers Pvt. Ltd. 
'Prabhat Bhavan', 96, LBS MARG
Vikhroli (W), Mumbai 400 083 
India 
877-503-8965 
91 223 2946102
Visit this company's website


Facility : Gujarat, India

Joining and Sealing Materials

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Gasket/Sealing Materials
AB 09 >= 2" CLD 23 SBR
AED 50 T5 >= 4" CLD 23 EPDM
AED 67 T5 >= 4" CLD 23 EPDM
AED 85 T5 >= 4" CLD 23 EPDM
B 304 >= 2" CLD 23 SBR
BC 309 T 15 >= 2" CLD 23 SBR
BC 310 >= 2" CLD 23 SBR
BW 5910 >= 4" CLD 23 EPDM
CS3 >= 1 1/2" CLD 23 SBR
CS4 >= 2" CLD 23 SBR
D 555 >= 2" CLD 23 EPDM
D-719 >= 1" C. HOT EPDM
IEH 78 >= 4" CLD 23 EPDM
KH 1 >= 2" CLD 23 SBR
KH 2 >= 2" CLD 23 SBR
KH 4 >= 2" CLD 23 SBR
KH06 >= 2" CLD 23 SBR
KS1 >= 2" CLD 23 SBR
KS1 T7 >= 2" CLD 23 SBR
KS2 >= 2" CLD 23 SBR
KS2 T7 >= 2" CLD 23 SBR
S4 >= 1 1/2" CLD 23 SBR
S5 >= 1 1/2" CLD 23 SBR
S6 >= 1 1/2" CLD 23 SBR
SE1 >= 2" CLD 23 EPDM
UB 70E >= 1" CLD 23 EPDM
UB 75 E >= 2" C. HOT EPDM
ULE 5 >= 4" CLD 23 EPDM



 
Praher Plastics Canada Ltd. 
101 Saunders Road
Barrie, ON L4N9A7 
Canada 
705-725-1100


Facility : Schwertberg, Austria

Mechanical Devices

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Strainer[1] [G]
PVC Line Strainer-S4 -PP Screen/EPDM 3/8" - 4" CLD 23 MLTPL
PVC Line Strainer-S4 -Stainless Screen/EPDM 3/8" - 4" CLD 23 MLTPL

[1] Certified for following connection types:
    - Solvent Socket/Spigot (DIN/ASTM/JIS)
    - Threaded Socket (BSP)
    - Fusion Socket/Spigot (DIN)
[G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for
    “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state
    laws and the U.S. Safe Drinking Water Act.

    



 
Precision Associates Inc. 
3800 Washington Avenue North
Minneapolis, MN 55412 
United States 
612-333-7464
Visit this company's website


Facility : Minneapolis, MN

Joining and Sealing Materials

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Gasket/Sealing Materials
23761[1] [2] C. HOT EPDM

[1] This product has also been evaluated for use in Mechanical Plumbing Device applications
    with a maximum use restriction of 0.4 sq. in./L.
[2] Certified for a maximum surface area to volume ratio of 2.0 sq. in./L.

O-Rings
23761[1] [2] C. HOT EPDM

[1] This product has also been evaluated for use in Mechanical Plumbing Device applications
    with a maximum use restriction of 0.4 sq. in./L.
[2] Certified for a maximum surface area to volume ratio of 2.0 sq. in./L.



 
Precix Inc. 
744 Belleville Avenue
New Bedford, MA 02745 
United States 
508-998-4142


Facility : New Bedford, MA

Joining and Sealing Materials

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Gasket/Sealing Materials[1]
E-17331/E61/70 durometer [2] C. HOT EPDM
E-17575/E175/80 durometer [2] C. HOT EPDM

[1] Only products bearing the NSF Mark on the product, product packaging, and/or
    documentation shipped with the product are Certified.	
[2] Certified for a maximum surface area to volume ratio of 2.0 sq. in./L.



 
Premier Construction Products, Group, a Div of Premier Magnesia, LLC 
109 Giles Place
Waynesville, NC 28786 
United States 
800-227-4287 
828-452-4784
Visit this company's website


Facility : Bayville, NJ

Protective (Barrier) Materials

    Water Water
  Water Contact Contact Contact
Trade Designation Size Restriction Temp Material

Concrete Admixtures
PREVent-C® 100 Shrinkage-Reducing/Compensating Admixture [1] [2] CLD 23 CMNT
PREVent-C® 500 Shrinkage-Reducing/Compensating Admixture [1] [2] CLD 23 CMNT

[1] Certified for a level not to exceed 5 pounds per 100 pounds of cement.
[2] Certified for use in tanks 500,000 gallons and greater.



 
Premier Repak, Inc. 
8351 185th Street
Tinley Park, IL 60487 
United States 
855-737-2500 
708-444-2688


Facility : # 1 USA

Joining and Sealing Materials

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Lubricants
PR5501 >= 1/2" C. HOT LUB

Thread Compounds
PR5501 >= 1/2" C. HOT LUB



PremierRepak, lnc. 
8351 185th Street
Tinley Park, IL 60487 
United States 
855-737-2500 


Facility : # 1 USA

Joining and Sealing Materials

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Lubricants
PR 5501 - High Consistency Silicone Valve and Oring Lubricant >= 1/2" C. HOT SLC
Shurjoint EHC Lubricant, part #5172840064 >= 1/2" C. HOT SLC



 
Press-Seal Gasket Corporation 
2424 W. State Boulevard
Fort Wayne, IN 46808 
United States 
800-348-7325 
260-436-0521
Visit this company's website


Facility : Fort Wayne, IN

Joining and Sealing Materials

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Gasket/Sealing Materials
PS 55 IR/SBR-MB [1] CLD 23 MLTPL

[1] Certified for use in pipes 14" and greater.  Certification is for gasket only.

O-Rings
PS 55 IR/SBR-MB [1] CLD 23 MLTPL

[1] Certified for use in pipes 14" and greater.  Certification is for gasket only.



 
Primus Pipe and Tube, Inc. 
241 W. Clarke Street
Wildwood, FL 34785 
United States 
800-731-7473 
352-748-9267
Visit this company's website


Facility : Wildwood, FL

Pipes and Related Products

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Pipe[1] [G]
TP304/TP304L WLD 1/2" - 104" C. HOT SS
TP316/TP316L WLD 1/2" - 104" C. HOT SS

[1] Only products bearing the NSF Mark on the product, product packaging, and/or
    documentation shipped with the product are Certified.
[G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for
    “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state
    laws and the U.S. Safe Drinking Water Act.

    



 
Prince Minerals, Inc. 
14 East 44tth Street 5th Floor
New York, NY 10017 
United States 
646-747-4200
Visit this company's website


Facility : Leesburg, AL

Process Media

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Oxidative Media
Pyrolox Advantage 18 x 45 mesh CLD 23 OTHER

NOTE: Certified for water treatment plant applications.
      This product has not been evaluated for point of use applications.


Facility : Quincy, IL

Process Media

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Oxidative Media
Pyrolox™ [1] CLD 23 MNDOX

[1] Certified for the following US mesh sizes: 8 x 20, 20 x 40.  Certified for the following
    UK mesh sizes: 18/44.

NOTE: Certified for water treatment plant applications.
      This product has not been evaluated for point of use applications.


Facility : New Johnsonville, TN

Process Media

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Filtration Media
Pyrolox Pro 20 x 40 mesh CLD 23 MNDOX

Oxidative Media
Pyrolox Pro 20 x 40 mesh CLD 23 MNDOX

NOTE: Certified for water treatment plant applications.
      This product has not been evaluated for point of use applications.


 
Process Systems, Inc. / Deming Vertical Turbine Group 
23633 Pinewood
Warren, MI 48091 
United States 
586-757-5711
Visit this company's website


Facility : Warren, MI

Mechanical Devices

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Submersible Pump - Pump Ends[1] [2] [G]
Model 4700 Series 5" - 24" CLD 23 MLTPL

[1] Certified for a minimum daily flow of 81,765 liters.
[2] Series 4700 includes the following:
    Model 4700: Water Lubricated Deep Well Pump
    Model 4705: Transfer Pump (Liquid Lock, Seal or Packed)
    Model 4770: Oil Lubricated Deep Well Pump
    Model 4771: SST - Superstandard Turbines
    Model 4772: Product Lubricated Pump with "T" Discharge Head
    Model 4773: Product Lubricated Pump with "G" Discharge Head
[G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for
    “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state
    laws and the U.S. Safe Drinking Water Act.

    



 
Prodeflon S.p.A. 
Via Dei Mille 127/129
24060 Castelli Calepio ( BG ) 
Italy 
39 03 544 25455
Visit this company's website


Facility : Castelli Calepio, Italy

Joining and Sealing Materials

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Gasket/Sealing Materials [G]
F 1000[1] [2] C. HOT PTFE
F 1500[1] [2] C. HOT PTFE

[1] This product has also been evaluated for use in Mechanical Plumbing Device applications
    with a maximum use restriction of 15 sq. in./L.
[2] Certified for a maximum surface area to volume ratio of 15 sq. in./L.
[G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for
    “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state
    laws and the U.S. Safe Drinking Water Act.

    

O-Rings [G]
F 1000[1] [2] C. HOT PTFE
F 1500[1] [2] C. HOT PTFE

[1] This product has also been evaluated for use in Mechanical Plumbing Device applications
    with a maximum use restriction of 15 sq. in./L.
[2] Certified for a maximum surface area to volume ratio of 15 sq. in./L.
[G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for
    “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state
    laws and the U.S. Safe Drinking Water Act.

    



 
Professional Coating Technologies, Inc. 
1001 Mount Lebanon Road
Cedar Hill, TX 75104 
United States 
972-291-7474
Visit this company's website


Facility : Cedar Hill, TX

Protective (Barrier) Materials

    Water Water
  Water Contact Contact Contact
Trade Designation Size Restriction Temp Material

Coatings - Fittings
MOS-50-OD/ID[1] 3/4" - 64" CLD 23 ASPH
MPFC-S.5™[2] 3/4" - 64" CLD 23 ASPH

[1] Number of Coats: 1-4
    Maximum Field Use Dry Film Thickness (in mils): 8 mils wet film thickness (approximately
    5 mils dry film thickness)
    Maximum Thinner: Thinning is not required.
    Recoat Cure Time and Temperature: At 70°F or higher, product may be immediately
    recoated.
    Final Cure Time and Temperature: 7 days at 70°C
    Special Comments: Heat the paint to 120-145°F prior to application. Maintain adequate
    air circulation and ventilation during curing period. Atomized air drying system is
    highly recommended. Apply paint onto the pipe substrate with a minimum coating
    temperature of 145°F. Flush wash the pipe until the water meets AWWA standards, or flush
    wash the pipe with running water for 10 hours.
[2] Number of Coats: 1 	
    Maximum Field Use Dry Film Thickness (in mils): 5 (8 wet mils)
    Final Cure Time and Temperature: 24 hours at 70°F
    Special Comments: The substrate should be between 60°F and 180°F prior to coating
    application.  The emulsion should be preheated to 70°F to 120°F before application.

Coatings - Pipe
MOS-50-OD/ID[1] 3/4" - 64" CLD 23 ASPH
MPFC-S.5™[2] 3/4" - 64" CLD 23 ASPH

[1] Number of Coats: 1-4
    Maximum Field Use Dry Film Thickness (in mils): 8 mils wet film thickness (approximately
    5 mils dry film thickness)
    Maximum Thinner: Thinning is not required.
    Recoat Cure Time and Temperature: At 70°F or higher, product may be immediately
    recoated.
    Final Cure Time and Temperature: 7 days at 70°C
    Special Comments: Heat the paint to 120-145°F prior to application. Maintain adequate
    air circulation and ventilation during curing period. Atomized air drying system is
    highly recommended. Apply paint onto the pipe substrate with a minimum coating
    temperature of 145°F. Flush wash the pipe until the water meets AWWA standards, or flush
    wash the pipe with running water for 10 hours.
[2] Number of Coats: 1 	
    Maximum Field Use Dry Film Thickness (in mils): 5 (8 wet mils)
    Final Cure Time and Temperature: 24 hours at 70°F
    Special Comments: The substrate should be between 60°F and 180°F prior to coating
    application.  The emulsion should be preheated to 70°F to 120°F before application.

Coatings - Valve
MOS-50-OD/ID[1] 3/4" - 64" CLD 23 ASPH
MPFC-S.5™[2] 3/4" - 64" CLD 23 ASPH

[1] Number of Coats: 1-4
    Maximum Field Use Dry Film Thickness (in mils): 8 mils wet film thickness (approximately
    5 mils dry film thickness)
    Maximum Thinner: Thinning is not required.
    Recoat Cure Time and Temperature: At 70°F or higher, product may be immediately
    recoated.
    Final Cure Time and Temperature: 7 days at 70°C
    Special Comments: Heat the paint to 120-145°F prior to application. Maintain adequate
    air circulation and ventilation during curing period. Atomized air drying system is
    highly recommended. Apply paint onto the pipe substrate with a minimum coating
    temperature of 145°F. Flush wash the pipe until the water meets AWWA standards, or flush
    wash the pipe with running water for 10 hours.
[2] Number of Coats: 1 	
    Maximum Field Use Dry Film Thickness (in mils): 5 (8 wet mils)
    Final Cure Time and Temperature: 24 hours at 70°F
    Special Comments: The substrate should be between 60°F and 180°F prior to coating
    application.  The emulsion should be preheated to 70°F to 120°F before application.



 
Proflex Precision Manufacturing Co., Ltd. 
Daaoli Industries Zone, Shamen Town
Yuhuan, Taizhou 
Zhejiang 317607 
China 
86 576 8742 7412


Facility : Zhejiang, China

Pipes and Related Products

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Fittings
PFA102-6-6 - PEX ELBOW 3/8" x 3/8" C. HOT BRASS
PFA102-8-8 - PEX ELBOW 1/2" x 1/2"  C. HOT BRASS
PFA102-8-12 - PEX ELBOW 1/2" x 3/4" C. HOT BRASS
PFA102-10-10 - PEX ELBOW  5/8" x 5/8" C. HOT BRASS
PFA102-12-12 - PEX ELBOW 3/4" x 3/4" C. HOT BRASS
PFA102-12-16 - PEX ELBOW 3/4" x 1" C. HOT BRASS
PFA102-16-16 - PEX ELBOW 1" x 1" C. HOT BRASS
PFA103-6-8 - PEX x FEMALE NPT WALL PLATE ELBOW-3 DROP EAR 3/8" x 1/2" C. HOT BRASS
PFA103-8-8 - PEX x FEMALE NPT WALL PLATE ELBOW-3 DROP EAR 1/2" x 1/2" C. HOT BRASS
PFA103-8-12 - PEX x FEMALE NPT WALL PLATE ELBOW-3 DROP EAR 1/2" x 3/4" C. HOT BRASS
PFA103-12-8 - PEX x FEMALE NPT WALL PLATE ELBOW-3 DROP EAR 3/4" x 1/2"  C. HOT BRASS
PFA103-12-12 - PEX x FEMALE NPT WALL PLATE ELBOW-3 DROP EAR 3/4" x 3/4" C. HOT BRASS
PFA104-8-8 - PEX x FEMALE SWIVEL ELBOW 1/2" x 1/2" C. HOT BRASS
PFA104-8-12 - PEX x FEMALE SWIVEL ELBOW 1/2” x 3/4”  C. HOT BRASS
PFA104-12-12 - PEX x FEMALE SWIVEL ELBOW 3/4” x 3/4”  C. HOT BRASS
PFA105-8-8 - PEX x MALE NPT ELBOW 1/2” x 1/2”  C. HOT BRASS
PFA105-8-12 - PEX x MALE NPT ELBOW 1/2” x 3/4”  C. HOT BRASS
PFA105-12-12 - PEX x MALE NPT ELBOW 3/4” x 3/4”  C. HOT BRASS
PFA106-6-6-6 - PEX TEE 3/8” x 3/8” x 3/8”  C. HOT BRASS
PFA106-6-6-8 - PEX TEE 3/8” x 3/8” x 1/2”  C. HOT BRASS
PFA106-6-6-12 - PEX TEE 3/8” x 3/8” x 3/4”  C. HOT BRASS
PFA106-6-12-12 - PEX TEE 3/8” x 3/4” x 3/4”  C. HOT BRASS
PFA106-6-8-6 - PEX TEE 3/8” x 1/2” x 3/8”  C. HOT BRASS
PFA106-6-8-8 - PEX TEE 3/8” x 1/2” x 1/2”  C. HOT BRASS
PFA106-6-8-12 - PEX TEE 3/8” x 1/2” x 3/4”  C. HOT BRASS
PFA106-8-6-8 - PEX TEE 1/2” x 3/8” x 1/2”  C. HOT BRASS
PFA106-8-6-12 - PEX TEE 1/2” x 3/8” x 3/4”  C. HOT BRASS
PFA106-8-8-8 - PEX TEE 1/2” x 1/2” x 1/2”  C. HOT BRASS
PFA106-8-8-12 - PEX TEE 1/2” x 1/2” x 3/4”  C. HOT BRASS
PFA106-8-12-8 - PEX TEE 1/2” x 3/4” x 1/2”  C. HOT BRASS
PFA106-8-12-12 - PEX TEE 1/2” x 3/4” x 3/4”  C. HOT BRASS
PFA106-8-12-16 - PEX TEE 1/2” x 3/4” x 1” C. HOT BRASS
PFA106-8-16-16 - PEX TEE 1/2” x 1” x 1” C. HOT BRASS
PFA106-12-6-12 - PEX TEE 3/4” x 3/8” x 3/4”  C. HOT BRASS
PFA106-12-8-12 - PEX TEE 3/4” x 1/2” x 3/4”  C. HOT BRASS
PFA106-12-8-16 - PEX TEE 3/4” x 1/2” x 1” C. HOT BRASS
PFA106-12-12-12 - PEX TEE 3/4” x 3/4” x 3/4”  C. HOT BRASS
PFA106-16-12-16 - PEX TEE 1” x 3/4” x 1” C. HOT BRASS
PFA106-12-12-16 - PEX TEE 3/4” x 3/4” x 1” C. HOT BRASS
PFA106-16-16-16 - PEX TEE 1” x 1” x 1” C. HOT BRASS
PFA106-12-16-12 - PEX TEE 3/4” x 1” x 3/4”  C. HOT BRASS
PFA106-12-16-16 - PEX TEE 3/4” x 1” x 1” C. HOT BRASS
PFA106-16-8-16 - PEX TEE 1” x 1/2” x 1” C. HOT BRASS
PFA107-8-8-8 - MALE BRANCH TEE 1/2” x 1/2” x 1/2” C. HOT BRASS
PFA107-12-8-12 - MALE BRANCH TEE 3/4” x 1/2” x 3/4”  C. HOT BRASS
PFA108-6-6 - PEX COUPLING 3/8” x 3/8”  C. HOT BRASS
PFA108-6-8 - PEX COUPLING 3/8” x 1/2” C. HOT BRASS
PFA108-8-8 - PEX COUPLING 1/2” x 1/2” C. HOT BRASS
PFA108-8-12 - PEX COUPLING 1/2” x 3/4” C. HOT BRASS
PFA108-8-16 - PEX COUPLING 1/2” x 1” C. HOT BRASS
PFA108-12-12 - PEX COUPLING 3/4” x 3/4” C. HOT BRASS
PFA108-12-16 - PEX COUPLING 3/4” x 1” C. HOT BRASS
PFA108-16-16 - PEX COUPLING 1” x 1” C. HOT BRASS
PFA109-6-8 - PEX x MALE SWT ADAPTER 3/8” x 1/2” C. HOT BRASS
PFA109-8-8 - PEX x MALE SWT ADAPTER 1/2” x 1/2” C. HOT BRASS
PFA109-10-8 - PEX x MALE SWT ADAPTER 5/8” x 1/2” C. HOT BRASS
PFA109-10-12 - PEX x MALE SWT ADAPTER 5/8” x 3/4” C. HOT BRASS
PFA109-8-12 - PEX x MALE SWT ADAPTER 1/2” x 3/4” C. HOT BRASS
PFA109-12-12 - PEX x MALE SWT ADAPTER 3/4” x 3/4” C. HOT BRASS
PFA109-16-12 - PEX x MALE SWT ADAPTER 1” x 3/4” C. HOT BRASS
PFA109-16-16 - PEX x MALE SWT ADAPTER 1” x 1” C. HOT BRASS
PFA110-6-8 - PEX x FEMALE SWT ADAPTER 3/8" x 1/2" C. HOT BRASS
PFA110-8-8 - PEX x FEMALE SWT ADAPTER 1/2” x 1/2” C. HOT BRASS
PFA110-12-8 - PEX x FEMALE SWT ADAPTER 3/4” x 1/2” C. HOT BRASS
PFA110-10-8 - PEX x FEMALE SWT ADAPTER 5/8” x 1/2” C. HOT BRASS
PFA110-10-12 - PEX x FEMALE SWT ADAPTER 5/8” x 3/4” C. HOT BRASS
PFA110-8-12 - PEX x FEMALE SWT ADAPTER 1/2” x 3/4” C. HOT BRASS
PFA110-12-12 - PEX x FEMALE SWT ADAPTER 3/4” x 3/4” C. HOT BRASS
PFA110-16-12 - PEX x FEMALE SWT ADAPTER 1” x 3/4” C. HOT BRASS
PFA110-16-16 - PEX x FEMALE SWT ADAPTER 1” x 1” C. HOT BRASS
PFA111-8-8 - PEX x MALE SWT ELBOW 1/2” x 1/2” C. HOT BRASS
PFA111-8-12 - PEX x MALE SWT ELBOW 1/2” x 3/4” C. HOT BRASS
PFA111-12-12 - PEX x MALE SWT ELBOW 3/4” x 3/4” C. HOT BRASS
PFA112-8-8 - PEX x FEMALE SWT ELBOW 1/2” x 1/2” C. HOT BRASS
PFA112-12-12 - PEX x FEMALE SWT ELBOW 3/4” x 3/4”  C. HOT BRASS
PFA113-6-8 - PEX x MALE NPT ADAPTOR 3/8” x 1/2” C. HOT BRASS
PFA113-8-8 - PEX x MALE NPT ADAPTOR 1/2” x 1/2” C. HOT BRASS
PFA113-8-12 - PEX x MALE NPT ADAPTOR 1/2” x 3/4”  C. HOT BRASS
PFA113-12-8 - PEX x MALE NPT ADAPTOR 3/4” x 1/2” C. HOT BRASS
PFA113-10-8 - PEX x MALE NPT ADAPTOR 5/8” x 1/2” C. HOT BRASS
PFA113-12-12 - PEX x MALE NPT ADAPTOR 3/4” x 3/4” C. HOT BRASS
PFA113-12-16 - PEX x MALE NPT ADAPTOR 3/4” x 1” C. HOT BRASS
PFA113-16-12 - PEX x MALE NPT ADAPTOR 1” x 3/4” C. HOT BRASS
PFA113-16-16 - PEX x MALE NPT ADAPTOR 1” x 1” C. HOT BRASS
PFA114-6-8 - PEX x FEMALE NPT ADAPTER 3/8” x 1/2” C. HOT BRASS
PFA114-8-8 - PEX x FEMALE NPT ADAPTER 1/2” x 1/2”  C. HOT BRASS
PFA114-8-12 - PEX x FEMALE NPT ADAPTER 1/2” x 3/4” C. HOT BRASS
PFA114-12-8 - PEX x FEMALE NPT ADAPTER 3/4” x 1/2” C. HOT BRASS
PFA114-12-12 - PEX x FEMALE NPT ADAPTER 3/4” x 3/4”  C. HOT BRASS
PFA114-16-16 - PEX x FEMALE NPT ADAPTER 1” x 1” C. HOT BRASS
PFA115-6- PEX TEST PLUG 3/8”  C. HOT BRASS
PFA115-8 - PEX TEST PLUG 1/2” C. HOT BRASS
PFA115-12 - PEX TEST PLUG 3/4”  C. HOT BRASS
PFA115-16 - PEX PLUG 1” C. HOT BRASS
PFA116-6-8 - PEX x FEMALE NPT WALL PLATE ELBOW-2 DROP EAR 3/8” x 1/2” C. HOT BRASS
PFA116-8-8 - PEX x FEMALE NPT WALL PLATE ELBOW-2 DROP EAR 1/2” x 1/2” C. HOT BRASS
PFA116-8-12 - PEX x FEMALE NPT WALL PLATE ELBOW-2 DROP EAR 1/2” x 3/4” C. HOT BRASS
PFA116-12-8 - PEX x FEMALE NPT WALL PLATE ELBOW-2 DROP EAR 3/4” x 1/2”  C. HOT BRASS
PFA116-12-12 - PEX x FEMALE NPT WALL PLATE ELBOW-2 DROP EAR 3/4” x 3/4”  C. HOT BRASS
PFA117-8-8 - PEX x FEMALE SWIVEL ADAPTOR 1/2” x 1/2” C. HOT BRASS
PFA117-8-12 - PEX x FEMALE SWIVEL ADAPTOR 1/2” x 3/4”  C. HOT BRASS
PFA117-12-12 - PEX x FEMALE SWIVEL ADAPTOR 3/4” x 3/4” C. HOT BRASS
PFA118-8-8 - PEX x HOSE ID ADAPTOR 1/2” x 1/2” C. HOT BRASS
PFA118-12-12 - PEX x HOSE ID ADAPTOR 3/4” x 3/4”  C. HOT BRASS



 
ProGum Elastomer Technology Co., Ltd 
5F-9, No. 258, Liangcheng Road
Junghe City, New Taipei 23553 
Taiwan 
886 282278396
Visit this company's website


Facility : # 1 Taiwan

Joining and Sealing Materials

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Gasket/Sealing Materials
EP7037K [1] C. HOT EPDM
ES7060K[G] [1] C. HOT EPDM

[1] Certified for a maximum surface area to volume ratio of 2.0 sq. in./L.
[G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for
    “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state
    laws and the U.S. Safe Drinking Water Act.

    

O-Rings
ES7060K[G] [1] C. HOT EPDM

[1] Certified for a maximum surface area to volume ratio of 2.0 sq. in./L.
[G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for
    “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state
    laws and the U.S. Safe Drinking Water Act.

    



 
ProGum Elastomer Technology Co., Ltd. 
5F-9, No. 258, Liancheng Road
Junghe City, New Taipei City 
Taiwan 
886 2 8227 8396
Visit this company's website


Facility : Guangdong, China

Joining and Sealing Materials

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Gasket/Sealing Materials
ES7060K [1] C. HOT EPDM
NS7064K[2] [1] C. HOT NBR

[1] Certified for a maximum surface area to volume ratio of 2.0 square inches/L.
[2] This product has also been evaluated for use in Mechanical Plumbing Device applications
    with a maximum use restriction of 0.17 sq. in./L.

O-Rings
ES7060K [1] C. HOT EPDM
NS7064K[2] [1] C. HOT NBR

[1] Certified for a maximum surface area to volume ratio of 2.0 square inches/L.
[2] This product has also been evaluated for use in Mechanical Plumbing Device applications
    with a maximum use restriction of 0.17 sq. in./L.



 
Prominent Fluid Controls 
136 Industry Drive
Pittsburgh, PA 15275 
United States 
412-787-2484
Visit this company's website


Facility : Pittsburgh, PA

Mechanical Devices

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Chemical Metering Pumps
Beta (BT4B####PVT$)[1] 1/4"x3/16"-1/2"x3/8" CLD 23 MLTPL
Beta (BT4BXXXXNPE$)[2] 1/4" - 1/2" CLD 23 MLTPL
Beta (BT5B####PVT$)[1] 1/4"x3/16"-1/2"x3/8" CLD 23 MLTPL
Beta (BT5BXXXXNPE$)[2] 1/4" - 1/2" CLD 23 MLTPL
Concept Plus (CNPAXXXXNPE$)[2] 1/4" - 3/8" CLD 23 MLTPL
Concept Plus (CNPB####PVT2)[1] 1/4"x3/16-3/8"x1/4" CLD 23 MLTPL
Concept Plus (CNPBXXXXNPE$)[2] 1/4" - 3/8" CLD 23 MLTPL
Concept Plus (CNPa####PVT$)[1] 1/4"x3/16"-3/8"x1/4" CLD 23 MLTPL
Delta (DLTA####PVT2)[1] 1/8"x3/16"-1/2"x1/2" CLD 23 MLTPL
Delta (DLTAXXXXNPE$)[2] 1/2" CLD 23 MLTPL
Gamma/L (GALA####PVT$)[1] 1/4"x3/16"-1/2"x3/8" CLD 23 MLTPL
Gamma/L (GALAXXXXNPE$)[2] 1/4" - 1/2" CLD 23 MLTPL
Gamma/X (GMXA####PVT2)[1] 1/4"x3/16"-1/2"x3/8" CLD 23 MLTPL
Gamma/X (GMXA####PVT7)[1] 1/4"x3/16"-1/2"x3/8" CLD 23 MLTPL
Gamma/X (GMXAXXXXNPE$)[2] 1/2" CLD 23 MLTPL
Sigma/1 (S1BaH#####PVT@07)[1] 1/2" - 3/4" CLD 23 MLTPL
Sigma/1 (S1CbH#####PVT@07)[1] 1/2" - 3/4" CLD 23 MLTPL
Sigma/2 (S2BaH#####PVT@07)[1] 1/2" - 1" CLD 23 MLTPL
Sigma/2 (S2CbH#####PVT@07)[1] 1/2" - 1" CLD 23 MLTPL
Sigma/3 (S3BaH######PVT@07)[1] 1" - 1 1/2" CLD 23 MLTPL
Sigma/3 (S3CbH######PVT@07)[1] 1" - 1 1/2" CLD 23 MLTPL

[1] #### - Pump version 
           Beta         - 0220, 0232, 0413, 0420, 0708, 0713, 1000, 1008, 1601, 1602, 
                          1604, 2001, 2002, 2504
           Concept Plus - 0215, 0308, 0704, 1000, 1002, 1601, 0309
           Delta        - 0280, 0450, 0730, 1020, 1608, 1612, 2508  
           Gamma/L      - 0220, 0232, 0413, 0420, 0708, 0713, 1000, 1005, 1008, 1601, 
                          1602, 1605  
           Gamma/X      - 1602, 1604, 0708, 1009, 0414, 0715, 0220, 0424  
           Sigma/1      - 04084, 04120, 07042, 07065, 10022, 10044, 10050, 12017, 12035     
    
           Sigma/2      - 04350, 07120, 07220, 16050, 16090, 16130
           Sigma/3      - 040830, 070410, 070580, 120145, 120190, 120270
    $    - Liquid End Version 
           0 - No bleed valve, no valve springs 
           2 - With bleed valve, no valve springs 
           7 - Self bleeding, with groove
    @    - Diaphragm 
           0 - Standard Diaphragm, PTFE Version (Non-Sigma)
           1 - Double Diaphragm with diaphragm rupture indicator (Non-Sigma)
           A - Safety Diaphragm with stop function (Sigma only)
           S - Safety Diaphragm with visual indicator (Sigma only)
    &    - Positive Displacement Element 
           0 - Standard Diaphragm, PTFE Version 
           1 - With membrane rupture signaling
    
    Any codes not specifically indicated in the trade name or listing notes represent
    features that do not affect the parts of the pump in contact with the media. Any
    value(s) are acceptable for these codes.
    Certification does NOT include any accessories (foot valve, injection valve and/or
    tubing). Certification does NOT include the plate valve option for the Sigma/3.
    
    These pumps are approved for use with the following media at the maximum concentrations
    listed below. These products are evaluated by diluting the exposed water treatment
    chemical to its maximum use level (MUL), as defined in NSF/ANSI Standard 60.
    ACH Aluminum chlorohydrate (40%)
    Aluminum sulfate (50%)
    Ammonium hydroxide (29%)
    Chlorine dioxide (2.0%)
    Ferric chloride (45%)
    Fluorosilicic acid (25%)
    Hydrochloric acid (33%)
    Liquid ammonium Sulfate (40%)
    Phosphoric acid (85%)
    Polyaluminum chloride (45%)
    Potassium permanganate (3%)
    Sodium bisulfite (44%)
    Sodium chlorite (25%)
    Sodium fluoride (4.0%)
    Sodium hydroxide (50%)
    Sodium hypochlorite (15%)
    Sodium permanganate (20%)
    Sulfuric acid (98%)
    Zinc orthophosphate (100%)
[2] XXXX - Pump version 

           Beta         - 0220, 0232, 0413, 0420, 0708, 0713, 1000, 1008, 1601, 

                          1602, 1604, 2001, 2002, 2504

           Concept Plus - 0308, 0215, 0704, 1000, 1002, 1601, 0309

           Delta        - 1020, 1608, 1612, 2508, 0730

           Gamma/L      - 232, 420, 713, 1000, 1005, 1008, 1601, 1602, 1605
, 0708, 0413, 
                          0220
           Gamma/X      - 2504, 1604, 0708, 1009, 0414, 0715, 0220, 0424, 0245, 2002, 1602
    $    - Liquid end version 
           0 - No bleed valve, no valve springs 
           2 - With bleed valve, no valve springs 
    
    Any codes not specifically indicated in the trade name or listing notes represent
    features that do not affect the parts of the pump in contact with the media. Any
    value(s) are acceptable for these codes. 
    
    Certification does NOT include any accessories (foot valve, injection valve and/or
    tubing).
    These pumps are Certified for use with the following media at the maximum concentrations
    listed below. These products are evaluated by diluting the exposed water treatment
    chemical to its maximum use level (MUL), as defined in NSF/ANSI Standard 60. 
    Ammonium hydroxide (29%)
    Liquid Ammonium sulfate (40%)
    Phosphoric acid (50%)
    Polyaluminum chloride (45%)
    Potassium permanganate (3%)
    Sodium fluoride (4.0%)
    Sodium hypochlorite (15%)
    Sodium Permanganate (20%)



 
Prominent Systems, Inc. 
13095 East Temple Avenue
City of Industry, CA 91746 
United States 
626-858-1888


Facility : Bandar Lampung, Indonesia

Process Media

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Granular Activated Carbon[1]
PS[5] [6] CLD 23 GAC
PS 12x30AW[3] 12 x 30 mesh CLD 23 GAC
PS 12x40AW[3] 12 x 40 mesh CLD 23 GAC
PS 20x50AW[3] 20 x 50 mesh CLD 23 GAC
PS 8x16AW[3] 8 x 16 mesh CLD 23 GAC
PS 8x20AW[3] 8 x 20 mesh CLD 23 GAC
PS 8x30AW[3] 8 x 30 mesh CLD 23 GAC
PSC 12x20[2] 12 x 20 mesh CLD 23 GAC
PSC 12x30[2] 12 x 30 mesh CLD 23 GAC
PSC 12x30AW[2] 12 x 30 mesh CLD 23 GAC
PSC 12x40[2] 12 x 40 mesh CLD 23 GAC
PSC 12x40AW[2] 12 x 40 mesh CLD 23 GAC
PSC 14x20[2] 14 x 20 mesh CLD 23 GAC
PSC 18x40[2] 18 x 40 mesh CLD 23 GAC
PSC 18x40AW[2] 18 x 40 mesh CLD 23 GAC
PSC 20x50[2] 20 x 50 mesh CLD 23 GAC
PSC 20x50AW[2] 20 x 50 mesh CLD 23 GAC
PSC 30x60[2] 30 x 60 mesh CLD 23 GAC
PSC 30x60AW[2] 30 x 60 mesh CLD 23 GAC
PSC 80x140[2] 80 x 140 mesh CLD 23 GAC
PSC 80x140AW[2] 80 x 140 mesh CLD 23 GAC
PSC 8x16[2] 8 x 16 mesh CLD 23 GAC
PSC 8x16AW[2] 8 x 16 mesh CLD 23 GAC
PSC 8x20[2] 8 x 20 mesh CLD 23 GAC
PSC 8x30[2] 8 x 30 mesh CLD 23 GAC
PSC 8x30AW[2] 8 x 30 mesh CLD 23 GAC

[1] Only products bearing the NSF Mark are Certified.
[2] The carbon source is coconut shell.
[3] The carbon source is coal.
[5] The carbon source is bituminous or lignite coal.
[6] Certified for the mesh sizes as follows: 8 x 16, 8 x 20, 8 x 30, 12 x 20, 12 x 30, 12 x
    40, 18 x 40, 20 x 50, and 30 x 60.

Powdered Activated Carbon[1]
PS[4] [5] [7] CLD 23 PAC
PSC 200[2] [4] 200 mesh CLD 23 PAC
PSC 325[2] [4] 325 mesh CLD 23 PAC
PSC 80x325[2] [4] 80 x 325 mesh CLD 23 PAC

[1] Only products bearing the NSF Mark are Certified.
[2] The carbon source is coconut shell.
[4] This product is Certified for a maximum use level of 250 mg/L.
[5] The carbon source is bituminous or lignite coal.
[7] Certified for the mesh sizes as follows: -200, -325, 80 x 140, and 80 x 325.

NOTE: Certified for water treatment plant applications.
      This product has not been evaluated for point of use applications.


 
Protec Arisawa Europe S.A. 
Aritz Bidea 67
48100 Mungia 
Spain 
34 9467 40312
Visit this company's website


Facility : Mungia, Spain

Mechanical Devices

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Filtration Devices/Components[1] [2] [3] [4]
1HFF608D3-20 8" D. HOT MLTPL
BPV-16-C-J-E 16" D. HOT MLTPL
BPV-8-F-G-H 8" D. HOT MLTPL
BPV-8-F-MCP-I 8" D. HOT MLTPL
BPV-HU10255MI 11" D. HOT MLTPL
PRO-11-C-D-E 11" D. HOT MLTPL
PRO-4-A-B 4" D. HOT MLTPL
PRO-8-C-D-E 8" D. HOT MLTPL
PRO-8-C-MCP-I 8" D. HOT MLTPL
PRO-HU10255MI 11" D. HOT MLTPL
Pall Xunc 8" D. HOT MLTPL
Ultipleat PA8040m 8" D. HOT MLTPL
Ultipleat PA8040s 8" D. HOT MLTPL
Ultipleat PA8060m 8" D. HOT MLTPL
Ultipleat PA8060s 8" D. HOT MLTPL

[1] All PRO and BPV series models can have a suffix of a -1 up through a -8 including -1.5
    and -7.5.
    
    The following nomenclature is used based on model type, where the indicators equal the
    following:
    PRO series: 
    A - 300/600/1000 
    B - EP/SP  
    C - 150/300/450/600/1000/1200 
    D - EP/SP/MSP/MMSP 
    E - 1/1.5/2/3/4/5/6/7/7.5/8 
    I - 3x2/3x3/4x4
    
    BPV Series:
    C - 150/300/450/600/1000/1200
    E - 1/1.5/2/3/4/5/6/7/7.5/8
    F - 1000/1200
    G - EP/SP/MSP/MMSP
    H - 1/1.5/2/3/4/5/6/7/7.5/8
    J - SP/MSP
    I - 3x2/3x3/4x4
[2] Certified for a minimum permeate flow of 327,000 L/day.
[3] The Listed size is the nominal housing diameter.
[4] Only products bearing the NSF Mark are NSF Certified.



 
Protech Chemicals Ltd. 
7600, Ouest Henri Bourassa
Saint-Laurent, QC H4S 1W3 
Canada 
514-745-0200
Visit this company's website


Facility : York, PA

Protective (Barrier) Materials

    Water Water
  Water Contact Contact Contact
Trade Designation Size Restriction Temp Material

Coatings - Fittings[1] [2] [G]
G17SNSB2 BLUE >= 1.5" D. HOT ACR
G17SNSM2 RUST >= 1.5" D. HOT ACR
G17SNSN2 BLACK >= 1.5" D. HOT ACR
G17SNSR2 RED >= 1.5" D. HOT ACR
G17SNSW2 WHITE >= 1.5" D. HOT ACR
WATERARMOR G17SNS >= 1.5" D. HOT ACR

[1] Colors: Black, blue, red, rust, white
    Number of coats: 1 - 2
    Maximum field use dry film thickness (in mils): 8
    Recoat cure time and temperature: 2 minutes at 175°C
    Final cure time and temperature: 2 minutes at 205°C
    Special comments: Cure time refers to melt time.
[2] Colors: Black, blue, red, rust, white
    Number of coats: 6
    Maximum field use dry film thickness (in mils): 40
    Recoat cure time and temperature: 2 minutes at 175°C
    Final cure time and temperature: 2 minutes at 205°C
    Special comments: Cure time refers to melt time.
[G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for
    “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state
    laws and the U.S. Safe Drinking Water Act.

    

Coatings - Pipe[1] [2] [G]
G17SNSB2 BLUE >= 1.5" D. HOT ACR
G17SNSM2 RUST >= 1.5" D. HOT ACR
G17SNSN2 BLACK >= 1.5" D. HOT ACR
G17SNSR2 RED >= 1.5" D. HOT ACR
G17SNSW2 WHITE >= 1.5" D. HOT ACR
WATERARMOR G17SNS >= 1.5" D. HOT ACR

[1] Colors: Black, blue, red, rust, white
    Number of coats: 1 - 2
    Maximum field use dry film thickness (in mils): 8
    Recoat cure time and temperature: 2 minutes at 175°C
    Final cure time and temperature: 2 minutes at 205°C
    Special comments: Cure time refers to melt time.
[2] Colors: Black, blue, red, rust, white
    Number of coats: 6
    Maximum field use dry film thickness (in mils): 40
    Recoat cure time and temperature: 2 minutes at 175°C
    Final cure time and temperature: 2 minutes at 205°C
    Special comments: Cure time refers to melt time.
[G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for
    “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state
    laws and the U.S. Safe Drinking Water Act.

    

Coatings - Tank[1] [2] [G]
G17SNSB2 BLUE >= 10 gal. D. HOT ACR
G17SNSM2 RUST >= 10 gal. D. HOT ACR
G17SNSN2 BLACK >= 10 gal. D. HOT ACR
G17SNSR2 RED >= 10 gal. D. HOT ACR
G17SNSW2 WHITE >= 10 gal. D. HOT ACR
WATERARMOR G17SNS >= 10 gal. D. HOT ACR

[1] Colors: Black, blue, red, rust, white
    Number of coats: 1 - 2
    Maximum field use dry film thickness (in mils): 8
    Recoat cure time and temperature: 2 minutes at 175°C
    Final cure time and temperature: 2 minutes at 205°C
    Special comments: Cure time refers to melt time.
[2] Colors: Black, blue, red, rust, white
    Number of coats: 6
    Maximum field use dry film thickness (in mils): 40
    Recoat cure time and temperature: 2 minutes at 175°C
    Final cure time and temperature: 2 minutes at 205°C
    Special comments: Cure time refers to melt time.
[G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for
    “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state
    laws and the U.S. Safe Drinking Water Act.

    

Coatings - Valve[1] [2] [G]
G17SNSB2 BLUE >= 1.5" D. HOT ACR
G17SNSM2 RUST >= 1.5" D. HOT ACR
G17SNSN2 BLACK >= 1.5" D. HOT ACR
G17SNSR2 RED >= 1.5" D. HOT ACR
G17SNSW2 WHITE >= 1.5" D. HOT ACR
WATERARMOR G17SNS >= 1.5" D. HOT ACR

[1] Colors: Black, blue, red, rust, white
    Number of coats: 1 - 2
    Maximum field use dry film thickness (in mils): 8
    Recoat cure time and temperature: 2 minutes at 175°C
    Final cure time and temperature: 2 minutes at 205°C
    Special comments: Cure time refers to melt time.
[2] Colors: Black, blue, red, rust, white
    Number of coats: 6
    Maximum field use dry film thickness (in mils): 40
    Recoat cure time and temperature: 2 minutes at 175°C
    Final cure time and temperature: 2 minutes at 205°C
    Special comments: Cure time refers to melt time.
[G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for
    “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state
    laws and the U.S. Safe Drinking Water Act.

    



 
Protective Coating Co. 
221 South 3rd Street
Allentown, PA 18102-4922 
United States 
610-432-3543


Facility : # 1 USA

Joining and Sealing Materials

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Patching Materials
PC-Plumbing Epoxy Putty [1] C. HOT EPOXY
PC-Metal [1] C. HOT EPOXY

[1] The exposed surface area of each sealant in a household distribution system should not
    exceed 1.3 sq. cm/L or .2 sq. in/L



 
PSI Water Technologies, Inc. 
1077 Dell Avenue
Suite A 
Campbell, CA 95008 
United States 
408-370-6540
Visit this company's website


Facility : Campbell, CA

Mechanical Devices

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Chemical Generators[1] [2]
MicrOclor N/A CLD 23 MLTPL
LC-20 N/A CLD 23 MLTPL
LC-40 N/A CLD 23 MLTPL
MC-10 N/A CLD 23 MLTPL
MC-20 N/A CLD 23 MLTPL
MC-40 N/A CLD 23 MLTPL
MC-60 N/A CLD 23 MLTPL
MC-80 N/A CLD 23 MLTPL
MC-100 N/A CLD 23 MLTPL
MC-160 N/A CLD 23 MLTPL
MC-200 N/A CLD 23 MLTPL
MC-300 N/A CLD 23 MLTPL
MC-400 N/A CLD 23 MLTPL
MC-500 N/A CLD 23 MLTPL
MC-600 N/A CLD 23 MLTPL
MC-800 N/A CLD 23 MLTPL
MC-900 N/A CLD 23 MLTPL
MC-1000 N/A CLD 23 MLTPL
MC-1200 N/A CLD 23 MLTPL
MC-1600 N/A CLD 23 MLTPL
MC-1800 N/A CLD 23 MLTPL
MC-1850 N/A CLD 23 MLTPL
MC-2000 N/A CLD 23 MLTPL
MC-2400 N/A CLD 23 MLTPL
MC-1500 N/A CLD 23 MLTPL

[1] Certification is based on a sodium hypochlorite solution of 6,400 mg/L for the MC-10 and
    8,000 mg/L for all other models, with a dosage rate yielding a maximum chlorine
    concentration of 10 mg/L into potable water.
[2] Certification of this product has been performed to the health effects requirements of
    NSF/ANSI Standard 61, which assesses the acceptability of potential extractants from the
    chemical generator.  No evaluation has been performed on the strength or efficacy of the
    chemical(s) generated. As unit operation, maintenance and the consistency of source
    ingredients may affect the performance of the unit, the ensuing chemical(s) is not
    Certified by NSF to NSF/ANSI Standard 60.

Miscellaneous Process Devices/Components[3] [G]
TANK Shark® N/A CLD 23 MLTPL

[3] Certified for use in tanks 25,000 gallons and greater.  Certification does not inlcude
    chemical generator.
[G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for
    “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state
    laws and the U.S. Safe Drinking Water Act.

    



 
PT Freeman Carbon Indonesia 
Desa Haduyang
Jalan Stasiun Kereta Api Tegeneneng 
Bandar Lampung 
Indonesia 
62 217 227 413
Visit this company's website


Facility : Bandar Lampung, Indonesia

Process Media

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Granular Activated Carbon[1]
FCI 1030 LPF 10 x 30 mesh CLD 23 GAC
FCI 1230 LPF 12 x 30 mesh CLD 23 GAC
FCI 1240 LPF 12 x 40 mesh CLD 23 GAC
FCI 2040 LPF 20 x 40 mesh CLD 23 GAC
FCI 2050 LPF 20 x 50 mesh CLD 23 GAC
FCI 3060 LPF 30 x 60 mesh CLD 23 GAC
FCI 3070 LPF 30 x 70 mesh CLD 23 GAC
FCI 814 LPF 8 x 14 mesh CLD 23 GAC
FCI 816 LPF 8 x 16 mesh CLD 23 GAC
FCI 830 LPF 8 x 30 mesh CLD 23 GAC

[1] The carbon source is coconut shell.

NOTE: Certified for water treatment plant applications.
      This product has not been evaluated for point of use applications.


 
PT Tansoputra Asia 
Jl. Penjernihan No 31
Pejompongan, Jakarta 10210 
Indonesia 
62 21 572 0439


Facility : Bandar Lampung, Indonesia

Process Media

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Granular Activated Carbon[1]
GAC 12x20[2] 12 x 20 mesh CLD 23 GAC
GAC 12x30[2] 12 x 30 mesh CLD 23 GAC
GAC 12x30AW[2] 12 x 30 mesh CLD 23 GAC
GAC 12x40[2] 12 x 40 mesh CLD 23 GAC
GAC 12x40AW[2] 12 x 40 mesh CLD 23 GAC
GAC 14x20[2] 14 x 20 mesh CLD 23 GAC
GAC 18x40[2] 18 x 40 mesh CLD 23 GAC
GAC 18x40AW[2] 18 x 40 mesh CLD 23 GAC
GAC 20x50[2] 20 x 50 mesh CLD 23 GAC
GAC 20x50AW[2] 20 x 50 mesh CLD 23 GAC
GAC 30x60[2] 30 x 60 mesh CLD 23 GAC
GAC 30x60AW[2] 30 x 60 mesh CLD 23 GAC
GAC 80x140[2] 80 x 140 mesh CLD 23 GAC
GAC 80x140AW[2] 80 x 140 mesh CLD 23 GAC
GAC 8x16[2] 8 x 16 mesh CLD 23 GAC
GAC 8x16AW[2] 8 x 16 mesh CLD 23 GAC
GAC 8x20[2] 8 x 20 mesh CLD 23 GAC
GAC 8x30[2] 8 x 30 mesh CLD 23 GAC
GAC 8x30AW[2] 8 x 30 mesh CLD 23 GAC
GAC Coal[3] [4] CLD 23 GAC
GC 12x30AW[5] 12 x 30 mesh CLD 23 GAC
GC 12x40AW[5] 12 x 40 mesh CLD 23 GAC
GC 20x50AW[5] 20 x 50 mesh CLD 23 GAC
GC 8x16AW[5] 8 x 16 mesh CLD 23 GAC
GC 8x20AW[5] 8 x 20 mesh CLD 23 GAC
GC 8x30AW[5] 8 x 30 mesh CLD 23 GAC

[1] Only products bearing the NSF Mark are Certified.
[2] The carbon source is coconut shell.
[3] The carbon source is bituminous or lignite coal.
[4] Certified for the mesh sizes as follows: 8 x 16, 8 x 20, 8 x 30, 12 x 20, 12 x 30, 12 x
    40, 18 x 40, 20 x 50, and 30 x 60.
[5] The carbon source is coal.

Powdered Activated Carbon[1]
PAC Coconut -200[2] -200 mesh CLD 23 PAC
PAC Coconut -325[2] -325 mesh CLD 23 PAC
PAC Coconut 80x325[2] 80 x 325 mesh CLD 23 PAC
Powdered Coal[3] [6] CLD 23 PAC

[1] Only products bearing the NSF Mark are Certified.
[2] The carbon source is coconut shell.
[3] The carbon source is bituminous or lignite coal.
[6] Certified for the mesh sizes as follows: -200, -325, 80 x 140, and 80 x 325.

NOTE: Certified for water treatment plant applications.
      This product has not been evaluated for point of use applications.


 
PT. Ikaindo Industri Karbonik Indonesia 
Ji. K.L. Yos Sudarso Km. 11.8
Medan 20244 
Indonesia 
62 61 685 1263


Facility : Medan, Indonesia

Process Media

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Granular Activated Carbon[1]
IKASORB W1030 10 x 30 mesh CLD 23 GAC
IKASORB W1230 12 x 30 mesh CLD 23 GAC
IKASORB W1230S[2] 12 x 30 mesh CLD 23 GAC
IKASORB W1230SA[3] 12 x 30 mesh CLD 23 GAC
IKASORB W1240 12 x 40 mesh CLD 23 GAC
IKASORB W1240S[2] 12 x 40 mesh CLD 23 GAC
IKASORB W1240SA[3] 12 x 40 mesh CLD 23 GAC
IKASORB W2050 20 x 50 mesh CLD 23 GAC
IKASORB W2050S[2] 20 x 50 mesh CLD 23 GAC
IKASORB W2050SA[3] 20 x 50 mesh CLD 23 GAC
IKASORB W3060 30 x 60 mesh CLD 23 GAC
IKASORB W3070 30 x 70 mesh CLD 23 GAC
IKASORB W814 8 x 14 mesh CLD 23 GAC
IKASORB W814S[2] 8 x 14 mesh CLD 23 GAC
IKASORB W814SA[3] 8 x 14 mesh CLD 23 GAC
IKASORB W816 8 x 16 mesh CLD 23 GAC
IKASORB W816S[2] 8 x 16 mesh CLD 23 GAC
IKASORB W816SA[3] 8 x 16 mesh CLD 23 GAC
IKASORB W830 8 x 30 mesh CLD 23 GAC
IKASORB W830S[2] 8 x 30 mesh CLD 23 GAC
IKASORB W830SA[3] 8 x 30 mesh CLD 23 GAC

[1] The carbon source is coconut shell.
[2] S suffix indicates a water washed product.
[3] SA suffix indicates an acid washed product.

NOTE: Certified for water treatment plant applications.
      This product has not been evaluated for point of use applications.


 
PT. Ikaindo Industri Karbonik Indonesia 
Ji. K.L. Yos Sudarso Km. 11.8
Medan 20244 
Indonesia 
62 61 685 1263


Facility : Medan, Indonesia

Process Media

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Granular Activated Carbon[1]
IKASORB W1030 10 x 30 mesh CLD 23 GAC
IKASORB W1230 12 x 30 mesh CLD 23 GAC
IKASORB W1230S[2] 12 x 30 mesh CLD 23 GAC
IKASORB W1230SA[3] 12 x 30 mesh CLD 23 GAC
IKASORB W1240 12 x 40 mesh CLD 23 GAC
IKASORB W1240S[2] 12 x 40 mesh CLD 23 GAC
IKASORB W1240SA[3] 12 x 40 mesh CLD 23 GAC
IKASORB W2050 20 x 50 mesh CLD 23 GAC
IKASORB W2050S[2] 20 x 50 mesh CLD 23 GAC
IKASORB W2050SA[3] 20 x 50 mesh CLD 23 GAC
IKASORB W3060 30 x 60 mesh CLD 23 GAC
IKASORB W3070 30 x 70 mesh CLD 23 GAC
IKASORB W814 8 x 14 mesh CLD 23 GAC
IKASORB W814S[2] 8 x 14 mesh CLD 23 GAC
IKASORB W814SA[3] 8 x 14 mesh CLD 23 GAC
IKASORB W816 8 x 16 mesh CLD 23 GAC
IKASORB W816S[2] 8 x 16 mesh CLD 23 GAC
IKASORB W816SA[3] 8 x 16 mesh CLD 23 GAC
IKASORB W830 8 x 30 mesh CLD 23 GAC
IKASORB W830S[2] 8 x 30 mesh CLD 23 GAC
IKASORB W830SA[3] 8 x 30 mesh CLD 23 GAC

[1] The carbon source is coconut shell.
[2] S suffix indicates a water washed product.
[3] SA suffix indicates an acid washed product.

NOTE: Certified for water treatment plant applications.
      This product has not been evaluated for point of use applications.


 
PT. Indopipe 
Kawasan Industri Gresik
Jl. Kig Raya Selatan Blok D 12A-26 
Gresik 61121 Jawa Timur 
Indonesia 
62 21 781 6512
Visit this company's website


Facility : Jawa Timur, Indonesia

Pipes and Related Products

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Pipe
INDOPIPE 20 mm - 1000 mm D. HOT HDPE

NOTE: Only products bearing the NSF Mark on the product, product packaging, and/or
      documentation shipped with the product are Certified.


 
PT. Matahari Putra Makmur 
Jl. Raya Gempol Bangil
Desa Cangkringmalang, Kecamatan. Beji 
Kabupaten Pasuruan, Jawa Timur 67154 
Indonesia 
62 34 365 9926 X28
Visit this company's website


Facility : Jawa Timur, Indonesia

Pipes and Related Products

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Fittings[G]
ELBOW TRILLIUN PUREFLO AW 1/2" - 4" CLD 23 MLTPL
FAUCET ELBOW TRILLIUN PUREFLO AW 1/2" - 3/4" CLD 23 MLTPL
FAUCET ELBOW TRILLIUN PUREFLO METAL INSERT 1/2" - 3/4" CLD 23 MLTPL
FAUCET SOCKET TRILLIUN PUREFLO AW 1/2" - 3/4" CLD 23 MLTPL
FAUCET SOCKET TRILLIUN PUREFLO METAL INSERT 1/2" - 3/4" CLD 23 MLTPL
FAUCET TEE TRILLUN PUREFLO AW 1/2" - 3/4" CLD 23 MLTPL
KNEE TRILLIUN Pureflo AW 1/2" - 1" CLD 23 MLTPL
PLUG TRILLIUN PUREFLO AW 1/2" - 3/4" CLD 23 MLTPL
SOCKET TRILLIUN PUREFLO AW 1/2" - 1 1/2" CLD 23 MLTPL
TEE TRILLIUN PUREFLO AW 1/2" - 1" CLD 23 MLTPL
VALVE SOCKET TRILLIUN PUREFLO AW 1/2" - 1 3/4" CLD 23 MLTPL

[G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for
    “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state
    laws and the U.S. Safe Drinking Water Act.

    

Pipe[G]
PIPA TRILLIUN Pureflo AW 1/2" - 12" CLD 23 PVC
PIPA TRILLIUN Pureflo D 1 1/4" - 12" CLD 23 PVC
uPVC Pipe Trilliun Pureflo 1/2" - 12" CLD 23 PVC

[G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for
    “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state
    laws and the U.S. Safe Drinking Water Act.

    



 
Pt. Warnatama Cemerlang 
Jl. Raya Sumengko Km 31.6
Wringin Anom 
Gresik East Java 61176 
Indonesia 
62 31 897 8555


Facility : East Java, Indonesia

Protective (Barrier) Materials

    Water Water
  Water Contact Contact Contact
Trade Designation Size Restriction Temp Material

Coatings - Tank
PU ICHITANE SERIES[1] [G] >= 5000 gal CLD 23 PUR

[1] Number of coats: 1-2
    Maximum field use dry film thickness
    (in mils): 3
    Maximum thinner: 20% ICHITANE Thinner
    Recoat cure time and temperature: 4 hours at 35°C
    Final cure time and temperature: 7 days at 35°C
    Special comments: Mix ratio of Base:Hardener is 80:20 by volume
[G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for
    “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state
    laws and the U.S. Safe Drinking Water Act.

    



 
Pulsafeeder SPO 
27101 Airport Road
Punta Gorda, FL 33982 
United States 
941-575-3841


Facility : # 1 China

Mechanical Devices

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Water Meters[G]
MTR100-G 5/8" x 3/4" CLD 23 MLTPL
MTR100-P 5/8" x 3/4" CLD 23 MLTPL
MTR101-G 5/8" x 3/4" CLD 23 MLTPL
MTR101-P 5/8" x 3/4" CLD 23 MLTPL
MTR102-G 5/8" x 3/4" CLD 23 MLTPL
MTR102-P 5/8" x 3/4" CLD 23 MLTPL
MTR103-G 5/8" x 3/4" CLD 23 MLTPL
MTR104-G 5/8" x 3/4" CLD 23 MLTPL
MTR104-P 5/8" x 3/4" CLD 23 MLTPL
MTR107-G 5/8" x 3/4" CLD 23 MLTPL
MTR107-P 5/8" x 3/4" CLD 23 MLTPL
MTR107-P-L 5/8" x 3/4" CLD 23 MLTPL
MTR300-G 1" CLD 23 MLTPL
MTR300-P 1" CLD 23 MLTPL
MTR301-G 1" CLD 23 MLTPL
MTR301-P 1" CLD 23 MLTPL
MTR302-G 1" CLD 23 MLTPL
MTR302-P 1" CLD 23 MLTPL
MTR304-G 1" CLD 23 MLTPL
MTR304-P 1" CLD 23 MLTPL
MTR304-P-H 1" CLD 23 MLTPL
MTR307-G 1" CLD 23 MLTPL
MTR307-P 1" CLD 23 MLTPL
MTR307-P-L 1" CLD 23 MLTPL
MTR310-G 1" CLD 23 MLTPL
MTR400-G 1 1/2" CLD 23 MLTPL
MTR400-P 1 1/2" CLD 23 MLTPL
MTR402-G 1 1/2" CLD 23 MLTPL
MTR402-P 1 1/2" CLD 23 MLTPL
MTR404-G 1 1/2" CLD 23 MLTPL
MTR404-P 1 1/2" CLD 23 MLTPL
MTR407-G 1 1/2" CLD 23 MLTPL
MTR407-P 1 1/2" CLD 23 MLTPL
MTR410-G 1 1/2" CLD 23 MLTPL
MTR500-G 2" CLD 23 MLTPL
MTR504-G 2" CLD 23 MLTPL
MTR507-G 2" CLD 23 MLTPL
MTR510-G 2" CLD 23 MLTPL

[G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for
    “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state
    laws and the U.S. Safe Drinking Water Act.

    



 
Pulsair Systems, Inc. 
13643 Northeast 126th Place
Kirkland, WA 98034 
United States 
800-582-7797 
425-455-1263
Visit this company's website


Facility : Kirkland, WA

Mechanical Devices

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Miscellaneous Process Devices/Components[1] [2]
Pulsair Accumulator Plate Assembly 10" - 18" CLD 23 SS

[1] Certified for use in tanks 20,000 gallons and greater.
[2] Certified for a 4-plate array.



 
Pulsed Hydraulics, Inc. 
15 Oro Beach Drive
Oroville, WA 98844 
United States 
800-641-1726 
800-641-1726
Visit this company's website


Facility : Marion, OH

Mechanical Devices

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Miscellaneous Process Devices/Components[1] [G]
Bubble Forming Plate DFP-8SS 8" x 5" CLD 23 SS

[1] Certified for use in tanks 50,000 gallons and greater.
[G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for
    “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state
    laws and the U.S. Safe Drinking Water Act.

    



 
Pure Asphalt Company 
3455 West 31st Place
Chicago, IL 60623 
United States 
773-247-7030
Visit this company's website


Facility : Chicago, IL

Joining and Sealing Materials

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Lubricants
Pure Lube 400 >= 1/2" CLD 23 LUB
Pure Lube 500 >= 1/2" CLD 23 LUB



Pure N Safe Water Technologies PVT. Ltd. 
B-11, Ground Floor, Shankar Garden
New Delhi 110018 
India 


Facility : # 1 China

Mechanical Devices

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Pressurized Water Storage Tanks[G]
PNS FRP TANK 7" - 63" >= 1 gal. D. HOT MLTPL

[G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for
    “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state
    laws and the U.S. Safe Drinking Water Act.

    



PureSeal Water Conditioning Company, LLC 
17 Tec Street
Hicksville, NY 11801 
United States 


Facility : Hicksville, NY

Mechanical Devices

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Miscellaneous Process Devices/Components[1]
PURESEAL 1" - 8" CLD 23 MLTPL

[1] Point-of-Entry System tested and certified by NSF International under NSF/ANSI Standard
    61 for Materials Safety Requirements Only. Not Certified for Contaminant Reductions or
    Structural Integrity by NSF International.



 
Pureteck Co., Inc. 
3668 Placentia Court
Chino, CA 91710 
United States 
909-627-0619
Visit this company's website


Facility : # 1 Indonesia

Process Media

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Granular Activated Carbon[1]
WT1030 10 x 30 mesh CLD 23 GAC
WT1230 12 x 30 mesh CLD 23 GAC
WT1230AW[3] 12 x 30 mesh CLD 23 GAC
WT1230WW[2] 12 x 30 mesh CLD 23 GAC
WT1240 12 x 40 mesh CLD 23 GAC
WT1240AW[3] 12 x 40 mesh CLD 23 GAC
WT1240WW[2] 12 x 40 mesh CLD 23 GAC
WT2050 20 x 50 mesh CLD 23 GAC
WT2050AW[3] 20 x 50 mesh CLD 23 GAC
WT2050WW[2] 20 x 50 mesh CLD 23 GAC
WT3060 30 x 60 mesh CLD 23 GAC
WT3070 30 x 70 mesh CLD 23 GAC
WT814 8 x 14 mesh CLD 23 GAC
WT814AW[3] 8 x 14 mesh CLD 23 GAC
WT814WW[2] 8 x 14 mesh CLD 23 GAC
WT816 8 x 16 mesh CLD 23 GAC
WT816AW[3] 8 x 16 mesh CLD 23 GAC
WT816WW[2] 8 x 16 mesh CLD 23 GAC
WT830 8 x 30 mesh CLD 23 GAC
WT830AW[3] 8 x 30 mesh CLD 23 GAC
WT830WW[2] 8 x 30 mesh CLD 23 GAC

[1] The carbon source is coconut shell.
[2] WW suffix indicates a water washed product.
[3] AW suffix indicates an acid washed product.

NOTE: Certified for water treatment plant applications.
      This product has not been evaluated for point of use applications.


 
PVI Industries LLC 
3209 Galvez Avenue
Fort Worth, TX 76111 
United States 
800-433-5654 
817-335-9531
Visit this company's website


Facility : # 3 USA

Mechanical Devices

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Valve[G]
V135 2" C. HOT MLTPL
V85 1 1/2" C. HOT MLTPL

[G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for
    “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state
    laws and the U.S. Safe Drinking Water Act.

    



Facility : Franklin, NH

Mechanical Devices

    Water Water
    Contact Contact
Trade Designation Size Temp Material

valve[G]
V23-N-N 3/4" CLD 23 MLTPL
V55-N-N 1" C. HOT MLTPL

[G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for
    “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state
    laws and the U.S. Safe Drinking Water Act.

    



 
Qatar German Gasket Factory 
New Industrial Area
Doha 
40806 
Qatar 
97444114404
Visit this company's website


Facility : Doha, Qatar

Joining and Sealing Materials

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Gasket/Sealing Materials
Infinity EPDM Rubber [1] D. HOT EPDM

[1] Certified for a maximum surface area to volume ratio of 2.0 square inches/L

O-Rings
Infinity EPDM Rubber [1] D. HOT EPDM

[1] Certified for a maximum surface area to volume ratio of 2.0 square inches/L



 
QED Environmental Systems Inc. 
P.O. Box 3726
Ann Arbor, MI 48106 
United States 
800-624-2026 
734-995-2547


Facility : Dexter, MI

Mechanical Devices

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Miscellaneous Process Devices/Components[1]
E-Z Tray® Model 24.4 SS DW [2] CLD 23 MLTPL
E-Z Tray® Model 24.6 SS DW [2] CLD 23 MLTPL
E-Z Tray® Model 36.4 SS DW [2] CLD 23 MLTPL
E-Z Tray® Model 36.6 SS DW [2] CLD 23 MLTPL
E-Z Tray® Model 48.4 SS DW [2] CLD 23 MLTPL
E-Z Tray® Model 48.6 SS DW [2] CLD 23 MLTPL
E-Z Tray® Model 72.4 SS DW [2] CLD 23 MLTPL
E-Z Tray® Model 72.6 SS DW [2] CLD 23 MLTPL
E-Z Tray® Model 96.4 SS DW [2] CLD 23 MLTPL
E-Z Tray® Model 96.6 SS DW [2] CLD 23 MLTPL
EZ-24.4SS-DW-HD [2] CLD 23 MLTPL
EZ-24.4SS-DW-HD-ST [2] CLD 23 MLTPL
EZ-24.6SS-DW-HD [2] CLD 23 MLTPL
EZ-24.6SS-DW-HD-ST [2] CLD 23 MLTPL
EZ-36.4SS-DW-HD [2] CLD 23 MLTPL
EZ-36.4SS-DW-HD-ST [2] CLD 23 MLTPL
EZ-36.6SS-DW-HD [2] CLD 23 MLTPL
EZ-36.6SS-DW-HD-ST [2] CLD 23 MLTPL
EZ-48.4SS-DW-HD [2] CLD 23 MLTPL
EZ-48.4SS-DW-HD-ST [2] CLD 23 MLTPL
EZ-48.6SS-DW-HD [2] CLD 23 MLTPL
EZ-48.6SS-DW-HD-ST [2] CLD 23 MLTPL
EZ-72.2SS-DW [2] CLD 23 MLTPL
EZ-72.2SS-DW-HD [2] CLD 23 MLTPL
EZ-72.2SS-DW-HD-ST [2] CLD 23 MLTPL
EZ-72.4SS-DW-HD [2] CLD 23 MLTPL
EZ-72.4SS-DW-HD-ST [2] CLD 23 MLTPL
EZ-72.6SS-DW-HD [2] CLD 23 MLTPL
EZ-72.6SS-DW-HD-ST [2] CLD 23 MLTPL
EZ-96.4SS-DW-HD [2] CLD 23 MLTPL
EZ-96.4SS-DW-HD-ST [2] CLD 23 MLTPL
EZ-96.6SS-DW-HD [2] CLD 23 MLTPL
EZ-96.6SS-DW-HD-ST [2] CLD 23 MLTPL

[1] Only products bearing the NSF Mark are NSF Certified.
[2] Certified for a minimum daily flow of 5,450 liters.



 
Qingdao Jindapeng Powder Technology Co., Ltd. 
Zhaojialing Park 586, Tongji Street
Jimo, Qingdao City 
Shandong 266228 
China 
86 532 82513968
Visit this company's website


Facility : Shandong, China

Protective (Barrier) Materials

    Water Water
  Water Contact Contact Contact
Trade Designation Size Restriction Temp Material

Coatings - Fittings[1]
JDP18NEY >= 2" D. HOT PEC
JDP18NEY BLACK >= 2" D. HOT PEC
JDP19NEY BLUE >= 2" D. HOT PEC

[1] Number of coats: 1
    Maximum Field Use Dry Film Thickness (in mils): 22 
    Final Cure Time and Temperature: 20 minutes at 180°C
    Special Comments: Preheat substrate to 190°C - 220°C

Coatings - Pipe[1]
JDP18NEY 2", 3", >= 8" D. HOT PEC
JDP18NEY BLACK 2", 3", >= 8" D. HOT PEC
JDP19NEY BLUE 2", 3", >= 8" D. HOT PEC

[1] Number of coats: 1
    Maximum Field Use Dry Film Thickness (in mils): 22 
    Final Cure Time and Temperature: 20 minutes at 180°C
    Special Comments: Preheat substrate to 190°C - 220°C

Coatings - Valve[1]
JDP18NEY >= 2" D. HOT PEC
JDP18NEY BLACK >= 2" D. HOT PEC
JDP19NEY BLUE >= 2" D. HOT PEC

[1] Number of coats: 1
    Maximum Field Use Dry Film Thickness (in mils): 22 
    Final Cure Time and Temperature: 20 minutes at 180°C
    Special Comments: Preheat substrate to 190°C - 220°C



 
QuakeWrap, Inc. 
6840 South Tucson Boulevard
Tucson, AZ 85756 
United States 
800-782-5397 
520-791-7000
Visit this company's website


Facility : Tucson, AZ

Protective (Barrier) Materials

    Water Water
  Water Contact Contact Contact
Trade Designation Size Restriction Temp Material

Coatings - Tank [G]
QuakeWrap™[1] >= 5,000 gal CLD 23 FRP

[1] Coating Details: 
    
    First Layer: 
    
    QuakeBond™ J201TC (Tack Coat) 
    Mix ratio (A:B): 2:1 by volume (or 100:44 by weight) 
    Number of Coats: 1 
    Maximum Dry Film Thickness (mils): 40 
    Cure Time and temperature (before second layer): None 
    
    Second Layer: 
    
    QuakeBond™ J300SR (Saturating Resin) 
    Mix ratio (A:B): 2:1 by volume (or 100:43 by weight) 
    Saturation rate of QuakeWrap™ VU18C carbon fabric is maximum 50% by volume of saturating
    resin, i.e. [vol. of resin/vol. of resin and fabric] <= 0.5 
    Coats: 1 
    Maximum Dry Film Thickness (mils): 50 
    
    Final cure time and temperature after final layer of saturated fabric is applied: 72
    hours @ Ambient temperature. The use of portable heaters is required to achieve this
    cure temperature. 
    
    Product shall be flushed for 1 hour at 10 gallons per minute prior to use. 
    
    Maximum Total Dry Film Thickness (mils): 90
    
    Pipe end use: Certified for use on new pipes.
[G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for
    “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state
    laws and the U.S. Safe Drinking Water Act.

    

Coatings - Pipe [G]
QuakeWrap™[1] >=8" CLD 23 FRP
StifPipe™ >=8" CLD 23 FRP

[1] Coating Details: 
    
    First Layer: 
    
    QuakeBond™ J201TC (Tack Coat) 
    Mix ratio (A:B): 2:1 by volume (or 100:44 by weight) 
    Number of Coats: 1 
    Maximum Dry Film Thickness (mils): 40 
    Cure Time and temperature (before second layer): None 
    
    Second Layer: 
    
    QuakeBond™ J300SR (Saturating Resin) 
    Mix ratio (A:B): 2:1 by volume (or 100:43 by weight) 
    Saturation rate of QuakeWrap™ VU18C carbon fabric is maximum 50% by volume of saturating
    resin, i.e. [vol. of resin/vol. of resin and fabric] <= 0.5 
    Coats: 1 
    Maximum Dry Film Thickness (mils): 50 
    
    Final cure time and temperature after final layer of saturated fabric is applied: 72
    hours @ Ambient temperature. The use of portable heaters is required to achieve this
    cure temperature. 
    
    Product shall be flushed for 1 hour at 10 gallons per minute prior to use. 
    
    Maximum Total Dry Film Thickness (mils): 90
    
    Pipe end use: Certified for use on new pipes.
[G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for
    “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state
    laws and the U.S. Safe Drinking Water Act.

    



 
Quality Supply Plastic Technology Factory Company Ltd. (ZENITH) 
Industrial City, Phase 5
P.O. Box 5032 
Jeddah 21422 
Saudi Arabia 
966 2 6081829
Visit this company's website


Facility : Jeddah, Saudi Arabia

Pipes and Related Products

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Fittings[1]
Zenith CPVC 45° Elbow (Slip x Slip) 1/2" - 4" C. HOT CPVC
Zenith CPVC 90° Elbow (Slip x Fipt) 1/2" - 1" C. HOT CPVC
Zenith CPVC 90° Elbow (Slip x Slip) 1/2" - 4" C. HOT CPVC
Zenith CPVC Blind Flange (Slip) 2" - 4" C. HOT CPVC
Zenith CPVC Cap (Slip) 1/2" - 4" C. HOT CPVC
Zenith CPVC Coupling (Slip x Slip) 1/2" - 4" C. HOT CPVC
Zenith CPVC Crossover 1/2" - 1" C. HOT CPVC
Zenith CPVC Female Adapter (Slip x Fipt) 1/2" - 2" C. HOT CPVC
Zenith CPVC Flange (Slip) one piece 2" - 4" C. HOT CPVC
Zenith CPVC Male Adapter (Mipt x Slip) 1/2" - 4" C. HOT CPVC
Zenith CPVC Reducer Bushing (Spig x Fipt) 1/2" - 1" C. HOT CPVC
Zenith CPVC Reducer Bushing (Spig x Slip) 1/2" - 4" C. HOT CPVC
Zenith CPVC Tee (Slip x Slip x Fipt) 1/2" - 1" C. HOT CPVC
Zenith CPVC Tee (Slip x Slip x Slip) 1/2" - 4" C. HOT CPVC
Zenith CPVC Threaded Flange (Fipt) one piece 2" - 4" C. HOT CPVC
Zenith CPVC USA 45° Elbow (Slip x Slip) 1/2" - 4" C. HOT CPVC
Zenith CPVC USA 90° Elbow (Slip x Fipt) 1/2" - 1" C. HOT CPVC
Zenith CPVC USA 90° Elbow (Slip x Slip) 1/2" - 4" C. HOT CPVC
Zenith CPVC USA Blind Flange (Slip) 2" - 4" C. HOT CPVC
Zenith CPVC USA Cap (Slip) 1/2" - 4" C. HOT CPVC
Zenith CPVC USA Coupling (Slip x Slip) 1/2" - 4" C. HOT CPVC
Zenith CPVC USA Female Adapter (Slip x Fipt) 1/2" - 2" C. HOT CPVC
Zenith CPVC USA Flange (Slip) one piece 2" - 4" C. HOT CPVC
Zenith CPVC USA Male Adapter (Mipt x Slip) 1/2" - 4" C. HOT CPVC
Zenith CPVC USA Reducer Bushing (Spig x Fipt) 1/2" - 1" C. HOT CPVC
Zenith CPVC USA Reducer Bushing (Spig x Slip) 1/2" - 4" C. HOT CPVC
Zenith CPVC USA Tee (Slip x Slip x Fipt) 1/2" - 1" C. HOT CPVC
Zenith CPVC USA Threaded Flange (Fipt) one piece 2" - 4" C. HOT CPVC
Zenith CPVC USA Union (Slip x Slip) 1/2" - 4" C. HOT CPVC
Zenith CPVC USA Van Stone Flange (Slip) 2" - 6" C. HOT CPVC
Zenith CPVC Union (Slip x Slip) 1/2" - 4" C. HOT CPVC
Zenith CPVC Van Stone Flange (Slip) 2" - 6" C. HOT CPVC
Zenith USA CPVC Tee (Slip x Slip x Slip) 1/2" - 4" C. HOT CPVC

[1] Only products bearing the NSF Mark on the product, product packaging, and/or
    documentation shipped with the product are Certified.

Pipe
Zenith CPVC 1/2" - 2 1/2" D. HOT CPVC



 
Quality Water Products 
25 Town Farm Road
South Barre, MA 01074 
United States 
978-355-6833


Facility : South Barre, MA

Pipes and Related Products

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Pipe[1]
Flanged Ductile Iron Pipe 3" - 64" CLD 23 CMNT
Grooved/Shouldered Joint Pipe 3" - 64' CLD 23 CMNT

[1] Certification extends to pipe only and does not include gaskets.



 
Quanzhou Jetom Hose Industry Co., Ltd. 
Province town of MeiYu Industrial
LunCang 
Nanan City, Fujian 362304 
China 
86 595 8614 9280
Visit this company's website


Facility : Nanan City, Fujian, China

Mechanical Plumbing Devices

Trade Designation      

Flexible Plumbing Connectors[1] [G]
H AA BC---XXX DN6 Flexible Plumbing Connectors      
H AA BC---XXX DN8 Flexible Plumbing Connectors      

[1] H AA BC---XXX are designated as follows:
    H - Hose
    AA - Type of hose (hose ID6mm, ID8mm )
         27 - Washing hose
         41 - Plastic steel hose
         51 - Sink hose
         52 - Stainless steel braiding hose
         53 - Nylon wire drawing hose
    BC - Type of Nut/Connection Fitting
         B - Brass Fittings: G3/8, G1/2, 1/4NPSM, 1/2NPSM, 9/16 UNEF, 11/16UNF,
    1/2-18UNS-2A, 
             G3/4, 7/16UNF, 5/16-24UNF-2A, 11/16-16UN-2B, 9/16-24UNEF-2B, Quick connection1,
    
             15/16UNS, M8*1, M8*0.75, 3/8UNF, 5/8-18UNF, Quick Connect;
             Polyamide Fittings: 1/2-18UNS-2A, 16/25-20UNEF-2B, M22*1.5-6g, quick 
             connection1, quick connection2, quick connection3
         C - Brass Fittings: M10x1, M12x1, M15x1, M15x1.5, 9/16 UNEF, 11/16UN-2B, 5/16UNF, 
             1/2-18UNS-2A, G3/4, 7/16UNF,5/16-24UNF-2A, 11/16-16UN-2B, 9/16-24UNEF-2B, 
             Quick connection1, 15/16UNS, M8*1, M8*0.75, 3/8UNF, G3/8, G1/2, 1/2NPSM, 
             5/8-18UNF, Quick Connect;
             Polyamide Fittings: 1/2-18UNS-2A, 16/25-20UNEF-2B, M22*1.5-6g, quick 
             connection1, quick connection2, quick connection3
    XXX - 10cm - 200cm
[G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for
    “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state
    laws and the U.S. Safe Drinking Water Act.

    



 
R. N. Eaton & Company, Inc. 
P.O. Box 9211
Riverside, MO 64168 
United States 
800-783-7985 
816-741-7985


Facility : Riverside, MO

Protective (Barrier) Materials

    Water Water
  Water Contact Contact Contact
Trade Designation Size Restriction Temp Material

Coatings - Pipe
#9183 Asphalt Pipe Coating[1] [G] >= 1/2" CLD 23 ASPH

[1] Number of Coats : 1
    Maximum Field Use Dry Film Thickness (in mils): 2
    Final Cure Time and Temperature: 48 hours at 75°F
[G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for
    “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state
    laws and the U.S. Safe Drinking Water Act.

    

[2] Number of Coats: 1-2
    Maximum Field Use Dry Film Thickness (in mils): 3
    Recoat Cure Time and Temperature: 1 hour at 23°C
    Final Cure Time and Temperature: 48 hours at 23°C


 
R. W. Sidley, Inc. 
436 Casement Avenue
P.O. Box 150 
Painesville, OH 44077 
United States 
800-536-9343 
440-951-5050


Facility : Thompson, OH

Process Media

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Gravel
Sidley Filter Gravel 1.6 mm - 64 mm CLD 23 SLDOX
Filtration Gravel 1.6 mm - 64 mm CLD 23 SLDOX
Support Gravel 1.6 mm - 64 mm CLD 23 SLDOX
Well Gravel 1.6 mm - 64 mm CLD 23 SLDOX

Sand
Sidley Filtration Media 0.25 mm - 2 mm CLD 23 SLDOX
Filtration Sand 0.25 mm - 2 mm CLD 23 SLDOX
Rapid Gravity Filter Sand 0.25 mm - 2 mm CLD 23 SLDOX
Slow Sand Filter Sand 0.25 mm - 2 mm CLD 23 SLDOX
Pool Filter Sand 0.25 mm - 2 mm CLD 23 SLDOX
Well Pack Sand 0.25 mm - 2 mm CLD 23 SLDOX
Pipe Lining Sand 0.25 mm - 2 mm CLD 23 SLDOX
High Rate Filter Sand 0.25 mm - 2 mm CLD 23 SLDOX

NOTE: Certified for water treatment plant applications.
      This product has not been evaluated for point of use applications.


 
R.L. Hudson & Company 
2000 West Tacoma
Broken Arrow, OK 74012 
United States 
918-663-1130


Facility : # 1 China

Joining and Sealing Materials

    Water Water
    Contact Contact
Trade Designation Size Temp Material

O-Rings
E3030-70[2] [1] C. HOT EPDM
N1030-70[3] [4] D. HOT NBR

[1] Certified for a maximum surface area to volume ratio of 2.0 sq. in./L.
[2] This product has also been evaluated for use in Mechanical Plumbing Device applications
    with a maximum surface area to volume ratio of 2.0 sq. in./L.
[3] Certified for a maximum surface area to volume ratio of 1.6 sq. in./L.
[4] This product has also been evaluated for use in Mechanical Plumbing Device applications
    with a maximum surface area to volume ratio of 0.1 sq. in./L.



 
R.L. Hudson & Company 
2000 West Tacoma
Broken Arrow, OK 74012 
United States 
918-259-6600


Facility : # 1 Taiwan

Joining and Sealing Materials

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Gasket/Sealing Materials
RL-N67015-A[2] [1] C. HOT NBR

[1] Certified for a maximum surface area to volume ratio of 0.5 sq. in./L.
[2] This product has also been evaluated for use in Mechanical Plumbing Device applications
    with a maximum surface area to volume ratio of 0.2 sq. in./L.

O-Rings
RL-N67015-A[2] [1] C. HOT NBR

[1] Certified for a maximum surface area to volume ratio of 0.5 sq. in./L.
[2] This product has also been evaluated for use in Mechanical Plumbing Device applications
    with a maximum surface area to volume ratio of 0.2 sq. in./L.


Mechanical Plumbing Devices

Trade Designation      

Gasket/Sealing Materials
RL-E37072-L[1]      

[1] Certified for a maximum surface area to volume ratio of 2.0 sq. in./L.

O-Rings
RL-E37072-L[1]      

[1] Certified for a maximum surface area to volume ratio of 2.0 sq. in./L.



 
R.W. Lyall & Company 
2665 Research Drive
Corona, CA 92882-6918 
United States 
957-270-1500
Visit this company's website


Facility : Chungbuk, Republic of Korea

Mechanical Devices

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Ball Valves[1] [G]
LYALL/POLYTEC PE Ball Valve 1/2" - 16" CLD 23 MLTPL

[1] Only products bearing the NSF Mark on the product, product packaging, and/or
    documentation shipped with the product are Certified.
[G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for
    “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state
    laws and the U.S. Safe Drinking Water Act.

    



 
Radice Gomma S.A.S. 
Via Pola Nr. 25/27
20096 Pioltello 
Italy 
39 2 92 66 135


Facility : Pioltello, Italy

Mechanical Plumbing Devices

Trade Designation      

Hose
Ecoflex[1] [2]      

[1] Certified for an inner diameter between 1mm - 13mm and a maximum length of 250 cm.
[2] Only products bearing the NSF Mark on the product, product packaging, and/or
    documentation shipped with the product are Certified.



 
Radici Plastics USA, Inc. 
960 Seville Road
Wadsworth, OH 44272 
United States 
800-733-7611 
330-336-7611
Visit this company's website


Facility : Cantonment, FL

Potable Water Materials

    Water Water
    Contact Contact
Trade Designation End Use Temp Material

Potable Water Materials
RADILON A 42 100 NAT[1] A,F,P CLD 23 NP
RADILON A 42 100 NAT[2] A,F C. HOT NP

[1] Certified for a maximum surface area to volume ratio of 75 sq. in./L.
[2] Certified for a maximum surface area to volume ratio of 300 sq. in./L.



 
Radius Systems Ltd. 
Radius House, Berristow Lane
South Normanton, Alfreton 
Derbyshire DE55 2JJ 
United Kingdom 
44 177 381 1112
Visit this company's website


Facility : Derbyshire, United Kingdom

Protective (Barrier) Materials

    Water Water
  Water Contact Contact Contact
Trade Designation Size Restriction Temp Material

Coatings - Fittings[1] [2]
Subcote FLP II >= 3" CLD 23 PUR

[1] Colors: Pale Sage Green
    Number of Coats: 1
    Maximum Field Use Dry Film Thickness (in mils): 40-276
    Maximum thinner: None
    Final Cure Time and Temperature: 1 hour at 3°C
    Special Comments: Mix ratio of Part A:B is 3:2 by volume or 100:72 by weight.  100%
    solids.  Product requires disinfection using 100mg/liter of free chlorine for periods up
    to 30 minutes.  After disinfection, the main shall be flushed with water for a minimum
    period of 1 hour at a minimum flow velocity of 0.5 m.s-1.
[2] Product requires disinfection using a maximum of 100mg/liter of free chlorine for
    periods up to 30 minutes maximum.  After disinfection, the main shall be flushed with
    water for a minimum period of 1 hour at a minimum flow velocity of 0.5 m.s-1.  Please
    reference manufacturer's product instructions for flushing recommendations for
    additional product size ranges.

Coatings - Pipe - Immediate Return to Service[1] [2] [3]
Subcote FLP II >= 3" CLD 23 PUR

[1] Colors: Pale Sage Green
    Number of Coats: 1
    Maximum Field Use Dry Film Thickness (in mils): 40-276
    Maximum thinner: None
    Final Cure Time and Temperature: 1 hour at 3°C
    Special Comments: Mix ratio of Part A:B is 3:2 by volume or 100:72 by weight.  100%
    solids.  Product requires disinfection using 100mg/liter of free chlorine for periods up
    to 30 minutes.  After disinfection, the main shall be flushed with water for a minimum
    period of 1 hour at a minimum flow velocity of 0.5 m.s-1.
[2] Product requires disinfection using a maximum of 100mg/liter of free chlorine for
    periods up to 30 minutes maximum.  After disinfection, the main shall be flushed with
    water for a minimum period of 1 hour at a minimum flow velocity of 0.5 m.s-1.  Please
    reference manufacturer's product instructions for flushing recommendations for
    additional product size ranges.
[3] Evaluated for Immediate Return to Service.

Coatings - Tank[1] [2]
Subcote FLP II >= 264 gal CLD 23 PUR

[1] Colors: Pale Sage Green
    Number of Coats: 1
    Maximum Field Use Dry Film Thickness (in mils): 40-276
    Maximum thinner: None
    Final Cure Time and Temperature: 1 hour at 3°C
    Special Comments: Mix ratio of Part A:B is 3:2 by volume or 100:72 by weight.  100%
    solids.  Product requires disinfection using 100mg/liter of free chlorine for periods up
    to 30 minutes.  After disinfection, the main shall be flushed with water for a minimum
    period of 1 hour at a minimum flow velocity of 0.5 m.s-1.
[2] Product requires disinfection using a maximum of 100mg/liter of free chlorine for
    periods up to 30 minutes maximum.  After disinfection, the main shall be flushed with
    water for a minimum period of 1 hour at a minimum flow velocity of 0.5 m.s-1.  Please
    reference manufacturer's product instructions for flushing recommendations for
    additional product size ranges.

Coatings - Valve[1] [2]
Subcote FLP II >= 3" CLD 23 PUR

[1] Colors: Pale Sage Green
    Number of Coats: 1
    Maximum Field Use Dry Film Thickness (in mils): 40-276
    Maximum thinner: None
    Final Cure Time and Temperature: 1 hour at 3°C
    Special Comments: Mix ratio of Part A:B is 3:2 by volume or 100:72 by weight.  100%
    solids.  Product requires disinfection using 100mg/liter of free chlorine for periods up
    to 30 minutes.  After disinfection, the main shall be flushed with water for a minimum
    period of 1 hour at a minimum flow velocity of 0.5 m.s-1.
[2] Product requires disinfection using a maximum of 100mg/liter of free chlorine for
    periods up to 30 minutes maximum.  After disinfection, the main shall be flushed with
    water for a minimum period of 1 hour at a minimum flow velocity of 0.5 m.s-1.  Please
    reference manufacturer's product instructions for flushing recommendations for
    additional product size ranges.



 
Rain Bird Corporation 
6991 East Southpoint Drive
Tucson, AZ 85756 
United States 
520-741-6513


Facility : Ningbo, China

Mechanical Devices

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Water Meters[G]
FM0625B 5/8" x 1/2" CLD 23 MLTPL
FM075B 5/8" x 3/4" CLD 23 MLTPL
FM100B 1" CLD 23 MLTPL
FM150B 1 1/2" CLD 23 MLTPL
FM200B 2" CLD 23 MLTPL

[G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for
    “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state
    laws and the U.S. Safe Drinking Water Act.

    



 
Rainwater Treatment Systems 
Yeni Mudanya Yolu 7 KM
Cinar Is Merkezi No. 2/7A 
Emek-Osmangazi, Bursa 
Turkey 
90 224 444 0420
Visit this company's website


Facility : Changhua Hsien, Taiwan

Mechanical Plumbing Devices

Trade Designation      

Faucets[G]
10064      
10065      

[G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for
    “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state
    laws and the U.S. Safe Drinking Water Act.

    



 
Raschig USA Inc. 
2201 East Lamar Boulevard
Suite 240 
Arlington, TX 76006 
United States 
800-678-0345 
281-449-9500


Facility : El Dorado, KS

Process Media

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Aeration
Nor-Pac Tower Packing 2", PP 2" CLD 23 PP
Jaeger Tri-Packs PP [1] CLD 23 PP
Low Profile Rings (LPR) [2] CLD 23 PP

[1] Jaeger Tri-Packs PP is Certified for the following diameters: 1" - 3.5".
[2] Low Profile Rings (LPR) is Certified for the following diameters: 1" - 3".

NOTE: Certified for water treatment plant applications.
      This product has not been evaluated for point of use applications.


 
Raven Industries, Engineered Films Division 
821 West Algonquin Street
Sioux Falls, SD 57104 
United States 
605-335-0174
Visit this company's website


Facility : Sioux Falls, SD

Protective (Barrier) Materials

    Water Water
  Water Contact Contact Contact
Trade Designation Size Restriction Temp Material

Liners[1]
Dura-Skrim K30B >= 5000 gal. CLD 23 PE
Dura-Skrim K30BD >= 5000 gal. CLD 23 PE
Dura-Skrim K30BK >= 5000 gal. CLD 23 PE
Dura-Skrim K30BW >= 5000 gal. CLD 23 PE
Dura-Skrim K36B >= 5000 gal. CLD 23 PE
Dura-Skrim K36BD >= 5000 gal. CLD 23 PE
Dura-Skrim K36BDT1 >= 5000 gal. CLD 23 PE
Dura-Skrim K36BDT2 >= 5000 gal. CLD 23 PE
Dura-Skrim K36BK >= 5000 gal. CLD 23 PE
Dura-Skrim K36BKT1 >= 5000 gal. CLD 23 PE
Dura-Skrim K36BKT2 >= 5000 gal. CLD 23 PE
Dura-Skrim K36BT1 >= 5000 gal. CLD 23 PE
Dura-Skrim K36BT2 >= 5000 gal. CLD 23 PE
Dura-Skrim K36BW >= 5000 gal. CLD 23 PE
Dura-Skrim K36BWT1 >= 5000 gal. CLD 23 PE
Dura-Skrim K36BWT2 >= 5000 gal. CLD 23 PE
Dura-Skrim K45B >= 5000 gal. CLD 23 PE
Dura-Skrim K45BD >= 5000 gal. CLD 23 PE
Dura-Skrim K45BDT1 >= 5000 gal. CLD 23 PE
Dura-Skrim K45BDT2 >= 5000 gal. CLD 23 PE
Dura-Skrim K45BK >= 5000 gal. CLD 23 PE
Dura-Skrim K45BKT1 >= 5000 gal. CLD 23 PE
Dura-Skrim K45BKT2 >= 5000 gal. CLD 23 PE
Dura-Skrim K45BT1 >= 5000 gal. CLD 23 PE
Dura-Skrim K45BT2 >= 5000 gal. CLD 23 PE
Dura-Skrim K45BW >= 5000 gal. CLD 23 PE
Dura-Skrim K45BWT2 >= 5000 gal. CLD 23 PE
Dura-Skrim KQ36B >= 5000 gal. CLD 23 PP
Dura-Skrim KQ36BK >= 5000 gal. CLD 23 PP
Dura-Skrim KQ36BW >= 5000 gal. CLD 23 PP
Dura-Skrim KQ45B >= 5000 gal. CLD 23 PP
Dura-Skrim KQ45BK >= 5000 gal. CLD 23 PP
Dura-Skrim KQ45BW >= 5000 gal. CLD 23 PP
Dura-Skrim N30B >= 5000 gal. CLD 23 PE
Dura-Skrim N30BD >= 5000 gal. CLD 23 PE
Dura-Skrim N30BK >= 5000 gal. CLD 23 PE
Dura-Skrim N30BW >= 5000 gal. CLD 23 PE
Dura-Skrim N36B >= 5000 gal. CLD 23 PE
Dura-Skrim N36BD >= 5000 gal. CLD 23 PE
Dura-Skrim N36BDT1 >= 5000 gal. CLD 23 PE
Dura-Skrim N36BDT2 >= 5000 gal. CLD 23 PE
Dura-Skrim N36BK >= 5000 gal. CLD 23 PE
Dura-Skrim N36BKT1 >= 5000 gal. CLD 23 PE
Dura-Skrim N36BKT2 >= 5000 gal. CLD 23 PE
Dura-Skrim N36BT1 >= 5000 gal. CLD 23 PE
Dura-Skrim N36BT2 >= 5000 gal. CLD 23 PE
Dura-Skrim N36BW >= 5000 gal. CLD 23 PE
Dura-Skrim N36BWT1 >= 5000 gal. CLD 23 PE
Dura-Skrim N36BWT2 >= 5000 gal. CLD 23 PE
Dura-Skrim N45B >= 5000 gal. CLD 23 PE
Dura-Skrim N45BD >= 5000 gal. CLD 23 PE
Dura-Skrim N45BDT1 >= 5000 gal. CLD 23 PE
Dura-Skrim N45BDT2 >= 5000 gal. CLD 23 PE
Dura-Skrim N45BK >= 5000 gal. CLD 23 PE
Dura-Skrim N45BKT1 >= 5000 gal. CLD 23 PE
Dura-Skrim N45BKT2 >= 5000 gal. CLD 23 PE
Dura-Skrim N45BT1 >= 5000 gal. CLD 23 PE
Dura-Skrim N45BT2 >= 5000 gal. CLD 23 PE
Dura-Skrim N45BW >= 5000 gal. CLD 23 PE
Dura-Skrim N45BWT1 >= 5000 gal. CLD 23 PE
Dura-Skrim N45BWT2 >= 5000 gal. CLD 23 PE
Dura-Skrim NQ30B >= 5000 gal. CLD 23 PP
Dura-Skrim NQ30BK >= 5000 gal. CLD 23 PP
Dura-Skrim NQ30BW >= 5000 gal. CLD 23 PP
Dura-Skrim NQ36B >= 5000 gal. CLD 23 PP
Dura-Skrim NQ36BK >= 5000 gal. CLD 23 PP
Dura-Skrim NQ36BW >= 5000 gal. CLD 23 PP
Dura-Skrim NQ45B >= 5000 gal. CLD 23 PP
Dura-Skrim NQ45BK >= 5000 gal. CLD 23 PP
Dura-Skrim NQ45BW >= 5000 gal. CLD 23 PP
Dura-Skrim NQ60B >= 5000 gal. CLD 23 PP

[1] Either side may be used as the water contact side.



 
Raychem RPG Pvt. Ltd. 
1101-116, Vishwa Deep
District Centre, Janakpuri 
New Delhi 110058 
India 
91 114 5753737


Facility : Maharashtra, India

Protective (Barrier) Materials

    Water Water
  Water Contact Contact Contact
Trade Designation Size Restriction Temp Material

Coatings - Fittings[1]
Raycote EP Intercoat 144 >= 8" CLD 23 EPOXY

[1] Colors: Red, Grey						
    Number Of Coats: 1-2						
    Maximium Field Use Dry Thickness (in mils): 40 (20 mils per coat)						
    Recoat Cure Time and Temperature: 12 hours at 25°C						
    Final Cure Time/Temperature: 7 days at 25°C						
    Special Comments: Mix ratio of Part A:B is 3:1 by volume. Preheat Part A to 60-70°C and
    Part B to 40-55°C.						
    

Coatings - Pipe[1]
Raycote EP Intercoat 144 >= 8" CLD 23 EPOXY

[1] Colors: Red, Grey