NSF Product and Service Listings

These NSF Official Listings are current as of Tuesday, December 23, 2025 at 12:15 a.m. Eastern Time. Please contact NSF to confirm the status of any Listing, report errors, or make suggestions.

Alert: NSF is concerned about fraudulent downloading and manipulation of website text. Always confirm this information by clicking on the below link for the most accurate information: http://info.nsf.org/Certified/Food_Processing/Listings.asp?Company=3U330&Standard=14159%2D1&

NSF/ANSI/3-A 14159-1
Hygiene Requirements for the Design of
Meat and Poultry Processing Equipment


 
Boston Gear, LLC 
701 Carrier Drive
Charlotte, NC 28216 
United States 
704-668-7322
Visit this company's website

Facility : Charlotte, NC

COMPONENTS:

Generation 2 Worm Gear Speed Reducer[1]
SS(1)(2)(3)7180(4)-(5)(6)(7)-(8)-(9)(10)-(11)-(12)-(13) 

[1] (1) OP STYLE denoted by:				
        BLANK - SOLID OUTPUT SHAFT				
        H     - HOLLOW OUTPUT				
    (2) MOTOR FLANGE denoted by 				
        F  - QUILL STYLE MOTOR FLANGE				
        QC - QUICK CONNECT MOTOR FLANGE				
    (3) REDUCTION TYPE denoted by:				
        BLANK - SINGLE REDUCTION				
        WP    - DOUBLE W/ PLANETARY PREFIX				
        WA    - COMPOUND A ORIENTATION				
        WB    - COMPOUND B ORIENTATION				
        WC    - COMPOUND C ORIENTATION				
        WD    - COMPOUND D ORIENTATION
    (4) BASE denoted by:				
        BLANK - NO BASE	
        B     - HORIZONTAL BASE	
        V     - OUTPUT FLANGE - RIGHT	
        W     - OUTPUT FLANGE - LEFT	
        T     - TORQUE ARM	
    (5) RATIO denoted by:				
        Single Reduction Valid Values from 5 to 100		
        Compound WA / WB / WC / WD Valid Values from 100 to 10,000		
        Planetary WP Valid Values from 25 to 500
    (6) LUBRICATION denoted by				
        BLANK - No Lubrication				
        K     - Kluber UH1 6-460				
        D     - Mobil SHC Cibus 460				
    (7) SEAL OPTIONS denoted by:				
        C  - IP69k rated OP seals	
        CT - IP69k OP seals and double IP seals	
    (8) NEMA MOTOR MOUNTING denoted by:				
        B5  - 56C		
        B7  - 140TC
        B9  - 180TC
        B11 - 210TC	
    (9) OUTPUT SHAFT denoted by				
        GS - OUTPUT LEFT	
        HS - DOUBLE PROJECTION	
        JS - OUTPUT RIGHT
    (10) MOUNTING POSITION (non-blank value req'd if K or D lubrication) denoted by:
         BLANK (only if no lube)	
         1
         2		
         3		
         4		
         5		
         6
    (11) OP BORE CODE (for hollow OP shaft only) denoted by:
         AP(Inch) or APM (Metric) followed by two digits denoting size				
         P (Inch) or PM (Metric) followed by two digits denoting size				
         TP (Inch) or TPM (Metric) followed by two digits denoting size
    (12) MOTOR (optional) denoted by:				
         FUTSS		
         GUTSS	
         HUT58SS	
         HUTF-5/8SS	
         HUTSS	
         HUTFSS
         JUTFSS	
         KUTFSS
         LUTFSS
         MUTFSS
         NUTFSS
         PUTFSS	
    (13) CONDUIT BOX LOCATION (if motor provided) denoted by:				
         0
         3		
         6	
         9

Stainless Steel Worm Gear Speed Reducer[2]
SS(1)713(2)(3)(4)(5)(6)(7)
SS(1)715(2)(3)(4)(5)(6)(7) 

[2] May have the following suffixes:
    (1) Optional Input Style Designation. Valid Values are F and QC
    (2) Optional Mounting Base. Valid values are B, V, W, and blank.
    (3) Gear ratio. A ratio is required. Valid values are 5 to 100.
    (4) Indicates the unit is filled with synthetic food grade lubricant.
        Blank means the unit has no lubricant.
        Valid values are K, D and Blank.
        K - Kluber UH1 6-460
        D - Mobil SHC Cibus 460
    (5) Motor mounting. A motor mounting is required. Valid values are
        B5, B7, B9, B11.
    (6) Shaft style. A shaft style is required. GS, HS, JS are valid values.
    (7) Optional mounting position designation. Valid values are
        1, 2, 3, 4, 5, 6, Blank.
    (8) Shaft bore designation. Required for any SSH type unit. Valid values
        are P or PM followed by two digits denoting bore size.

Generation 2 Worm Gear Speed Reducer[1]
SS(1)(2)(3)7210(4)-(5)(6)(7)-(8)-(9)(10)-(11)-(12)-(13) 

[1] (1) OP STYLE denoted by:				
        BLANK - SOLID OUTPUT SHAFT				
        H     - HOLLOW OUTPUT				
    (2) MOTOR FLANGE denoted by 				
        F  - QUILL STYLE MOTOR FLANGE				
        QC - QUICK CONNECT MOTOR FLANGE				
    (3) REDUCTION TYPE denoted by:				
        BLANK - SINGLE REDUCTION				
        WP    - DOUBLE W/ PLANETARY PREFIX				
        WA    - COMPOUND A ORIENTATION				
        WB    - COMPOUND B ORIENTATION				
        WC    - COMPOUND C ORIENTATION				
        WD    - COMPOUND D ORIENTATION
    (4) BASE denoted by:				
        BLANK - NO BASE	
        B     - HORIZONTAL BASE	
        V     - OUTPUT FLANGE - RIGHT	
        W     - OUTPUT FLANGE - LEFT	
        T     - TORQUE ARM	
    (5) RATIO denoted by:				
        Single Reduction Valid Values from 5 to 100		
        Compound WA / WB / WC / WD Valid Values from 100 to 10,000		
        Planetary WP Valid Values from 25 to 500
    (6) LUBRICATION denoted by				
        BLANK - No Lubrication				
        K     - Kluber UH1 6-460				
        D     - Mobil SHC Cibus 460				
    (7) SEAL OPTIONS denoted by:				
        C  - IP69k rated OP seals	
        CT - IP69k OP seals and double IP seals	
    (8) NEMA MOTOR MOUNTING denoted by:				
        B5  - 56C		
        B7  - 140TC
        B9  - 180TC
        B11 - 210TC	
    (9) OUTPUT SHAFT denoted by				
        GS - OUTPUT LEFT	
        HS - DOUBLE PROJECTION	
        JS - OUTPUT RIGHT
    (10) MOUNTING POSITION (non-blank value req'd if K or D lubrication) denoted by:
         BLANK (only if no lube)	
         1
         2		
         3		
         4		
         5		
         6
    (11) OP BORE CODE (for hollow OP shaft only) denoted by:
         AP(Inch) or APM (Metric) followed by two digits denoting size				
         P (Inch) or PM (Metric) followed by two digits denoting size				
         TP (Inch) or TPM (Metric) followed by two digits denoting size
    (12) MOTOR (optional) denoted by:				
         FUTSS		
         GUTSS	
         HUT58SS	
         HUTF-5/8SS	
         HUTSS	
         HUTFSS
         JUTFSS	
         KUTFSS
         LUTFSS
         MUTFSS
         NUTFSS
         PUTFSS	
    (13) CONDUIT BOX LOCATION (if motor provided) denoted by:				
         0
         3		
         6	
         9

Stainless Steel Worm Gear Speed Reducer[2]
SS(1)718(2)(3)(4)(5)(6)(7) 

[2] May have the following suffixes:
    (1) Optional Input Style Designation. Valid Values are F and QC
    (2) Optional Mounting Base. Valid values are B, V, W, and blank.
    (3) Gear ratio. A ratio is required. Valid values are 5 to 100.
    (4) Indicates the unit is filled with synthetic food grade lubricant.
        Blank means the unit has no lubricant.
        Valid values are K, D and Blank.
        K - Kluber UH1 6-460
        D - Mobil SHC Cibus 460
    (5) Motor mounting. A motor mounting is required. Valid values are
        B5, B7, B9, B11.
    (6) Shaft style. A shaft style is required. GS, HS, JS are valid values.
    (7) Optional mounting position designation. Valid values are
        1, 2, 3, 4, 5, 6, Blank.
    (8) Shaft bore designation. Required for any SSH type unit. Valid values
        are P or PM followed by two digits denoting bore size.

Generation 2 Worm Gear Speed Reducer[1]
SS(1)(2)(3)7240(4)-(5)(6)(7)-(8)-(9)(10)-(11)-(12)-(13)
SS(1)(2)(3)7260(4)-(5)(6)(7)-(8)-(9)(10)-(11)-(12)-(13) 

[1] (1) OP STYLE denoted by:				
        BLANK - SOLID OUTPUT SHAFT				
        H     - HOLLOW OUTPUT				
    (2) MOTOR FLANGE denoted by 				
        F  - QUILL STYLE MOTOR FLANGE				
        QC - QUICK CONNECT MOTOR FLANGE				
    (3) REDUCTION TYPE denoted by:				
        BLANK - SINGLE REDUCTION				
        WP    - DOUBLE W/ PLANETARY PREFIX				
        WA    - COMPOUND A ORIENTATION				
        WB    - COMPOUND B ORIENTATION				
        WC    - COMPOUND C ORIENTATION				
        WD    - COMPOUND D ORIENTATION
    (4) BASE denoted by:				
        BLANK - NO BASE	
        B     - HORIZONTAL BASE	
        V     - OUTPUT FLANGE - RIGHT	
        W     - OUTPUT FLANGE - LEFT	
        T     - TORQUE ARM	
    (5) RATIO denoted by:				
        Single Reduction Valid Values from 5 to 100		
        Compound WA / WB / WC / WD Valid Values from 100 to 10,000		
        Planetary WP Valid Values from 25 to 500
    (6) LUBRICATION denoted by				
        BLANK - No Lubrication				
        K     - Kluber UH1 6-460				
        D     - Mobil SHC Cibus 460				
    (7) SEAL OPTIONS denoted by:				
        C  - IP69k rated OP seals	
        CT - IP69k OP seals and double IP seals	
    (8) NEMA MOTOR MOUNTING denoted by:				
        B5  - 56C		
        B7  - 140TC
        B9  - 180TC
        B11 - 210TC	
    (9) OUTPUT SHAFT denoted by				
        GS - OUTPUT LEFT	
        HS - DOUBLE PROJECTION	
        JS - OUTPUT RIGHT
    (10) MOUNTING POSITION (non-blank value req'd if K or D lubrication) denoted by:
         BLANK (only if no lube)	
         1
         2		
         3		
         4		
         5		
         6
    (11) OP BORE CODE (for hollow OP shaft only) denoted by:
         AP(Inch) or APM (Metric) followed by two digits denoting size				
         P (Inch) or PM (Metric) followed by two digits denoting size				
         TP (Inch) or TPM (Metric) followed by two digits denoting size
    (12) MOTOR (optional) denoted by:				
         FUTSS		
         GUTSS	
         HUT58SS	
         HUTF-5/8SS	
         HUTSS	
         HUTFSS
         JUTFSS	
         KUTFSS
         LUTFSS
         MUTFSS
         NUTFSS
         PUTFSS	
    (13) CONDUIT BOX LOCATION (if motor provided) denoted by:				
         0
         3		
         6	
         9

Stainless Steel Worm Gear Speed Reducer[2]
SS(1)724(2)(3)(4)(5)(6)(7) 

[2] May have the following suffixes:
    (1) Optional Input Style Designation. Valid Values are F and QC
    (2) Optional Mounting Base. Valid values are B, V, W, and blank.
    (3) Gear ratio. A ratio is required. Valid values are 5 to 100.
    (4) Indicates the unit is filled with synthetic food grade lubricant.
        Blank means the unit has no lubricant.
        Valid values are K, D and Blank.
        K - Kluber UH1 6-460
        D - Mobil SHC Cibus 460
    (5) Motor mounting. A motor mounting is required. Valid values are
        B5, B7, B9, B11.
    (6) Shaft style. A shaft style is required. GS, HS, JS are valid values.
    (7) Optional mounting position designation. Valid values are
        1, 2, 3, 4, 5, 6, Blank.
    (8) Shaft bore designation. Required for any SSH type unit. Valid values
        are P or PM followed by two digits denoting bore size.

Generation 2 Worm Gear Speed Reducer[1]
SS(1)(2)(3)7320(4)-(5)(6)(7)-(8)-(9)(10)-(11)-(12)-(13) 

[1] (1) OP STYLE denoted by:				
        BLANK - SOLID OUTPUT SHAFT				
        H     - HOLLOW OUTPUT				
    (2) MOTOR FLANGE denoted by 				
        F  - QUILL STYLE MOTOR FLANGE				
        QC - QUICK CONNECT MOTOR FLANGE				
    (3) REDUCTION TYPE denoted by:				
        BLANK - SINGLE REDUCTION				
        WP    - DOUBLE W/ PLANETARY PREFIX				
        WA    - COMPOUND A ORIENTATION				
        WB    - COMPOUND B ORIENTATION				
        WC    - COMPOUND C ORIENTATION				
        WD    - COMPOUND D ORIENTATION
    (4) BASE denoted by:				
        BLANK - NO BASE	
        B     - HORIZONTAL BASE	
        V     - OUTPUT FLANGE - RIGHT	
        W     - OUTPUT FLANGE - LEFT	
        T     - TORQUE ARM	
    (5) RATIO denoted by:				
        Single Reduction Valid Values from 5 to 100		
        Compound WA / WB / WC / WD Valid Values from 100 to 10,000		
        Planetary WP Valid Values from 25 to 500
    (6) LUBRICATION denoted by				
        BLANK - No Lubrication				
        K     - Kluber UH1 6-460				
        D     - Mobil SHC Cibus 460				
    (7) SEAL OPTIONS denoted by:				
        C  - IP69k rated OP seals	
        CT - IP69k OP seals and double IP seals	
    (8) NEMA MOTOR MOUNTING denoted by:				
        B5  - 56C		
        B7  - 140TC
        B9  - 180TC
        B11 - 210TC	
    (9) OUTPUT SHAFT denoted by				
        GS - OUTPUT LEFT	
        HS - DOUBLE PROJECTION	
        JS - OUTPUT RIGHT
    (10) MOUNTING POSITION (non-blank value req'd if K or D lubrication) denoted by:
         BLANK (only if no lube)	
         1
         2		
         3		
         4		
         5		
         6
    (11) OP BORE CODE (for hollow OP shaft only) denoted by:
         AP(Inch) or APM (Metric) followed by two digits denoting size				
         P (Inch) or PM (Metric) followed by two digits denoting size				
         TP (Inch) or TPM (Metric) followed by two digits denoting size
    (12) MOTOR (optional) denoted by:				
         FUTSS		
         GUTSS	
         HUT58SS	
         HUTF-5/8SS	
         HUTSS	
         HUTFSS
         JUTFSS	
         KUTFSS
         LUTFSS
         MUTFSS
         NUTFSS
         PUTFSS	
    (13) CONDUIT BOX LOCATION (if motor provided) denoted by:				
         0
         3		
         6	
         9

Stainless Steel Worm Gear Speed Reducer[2]
SS(1)726(2)(3)(4)(5)(6)(7)
SS(1)732(2)(3)(4)(5)(6)(7)
SSH(1)713(2)(3)(4)(5)(6)(7)(8)
SSH(1)715(2)(3)(4)(5)(6)(7)(8)
SSH(1)718(2)(3)(4)(5)(6)(7)(8)
SSH(1)721(2)(3)(4)(5)(6)(7)(8)
SSH(1)724(2)(3)(4)(5)(6)(7)(8)
SSH(1)726(2)(3)(4)(5)(6)(7)(8)
SSH(1)732(2)(3)(4)(5)(6)(7)(8) 

[2] May have the following suffixes:
    (1) Optional Input Style Designation. Valid Values are F and QC
    (2) Optional Mounting Base. Valid values are B, V, W, and blank.
    (3) Gear ratio. A ratio is required. Valid values are 5 to 100.
    (4) Indicates the unit is filled with synthetic food grade lubricant.
        Blank means the unit has no lubricant.
        Valid values are K, D and Blank.
        K - Kluber UH1 6-460
        D - Mobil SHC Cibus 460
    (5) Motor mounting. A motor mounting is required. Valid values are
        B5, B7, B9, B11.
    (6) Shaft style. A shaft style is required. GS, HS, JS are valid values.
    (7) Optional mounting position designation. Valid values are
        1, 2, 3, 4, 5, 6, Blank.
    (8) Shaft bore designation. Required for any SSH type unit. Valid values
        are P or PM followed by two digits denoting bore size.

Number of matching Manufacturers is 1
Number of matching Products is 18
Processing time was 0 seconds