NSF Product and Service Listings

These NSF Official Listings are current as of Saturday, December 20, 2025 at 12:15 a.m. Eastern Time. Please contact NSF to confirm the status of any Listing, report errors, or make suggestions.

Alert: NSF is concerned about fraudulent downloading and manipulation of website text. Always confirm this information by clicking on the below link for the most accurate information: http://info.nsf.org/Certified/Lead_Content/Listings.asp?Standard=372%2DADD&Company=C0349274&

NSF/ANSI/CAN 372
Drinking Water System Components - Lead Content


 
Royal Coatings, Inc. 
2705 Concord Road
Belle Chasse, LA 70037 
United States 
800-815-8811 
504-392-8811

Facility : # 1 USA


Coatings - Pipe[1] [2]
   PC 2.8
   Seal coat ID
   Tuff Coat OD 

[1] Colors: Black
    Number of Coats: 1 - 4
    Maximum flied use dry film thickness (in mils): 5
    Recoat cure time and temperature : 7 days at 70°C (158°F)
    Final cure time and temperature: 7 days at 70°C (158°F)
    Special comments: Pre-heat coating and substrate to 120°F - 140°F (49°C - 60°C) prior to
    application. Maintain adequate air circulation and ventilation. During curing period
    atomized air drying system is highly recommended. Following application flush wash the
    pipe with running water for 10 hours.
[2] Only products bearing the NSF Mark on the product, product packaging, and/or
    documentation shipped with the product are Certified.

Coatings - Valve[1] [2]
   PC 2.8
   Seal coat ID
   Tuff Coat OD 

[1] Colors: Black
    Number of Coats: 1 - 4
    Maximum flied use dry film thickness (in mils): 5
    Recoat cure time and temperature : 7 days at 70°C (158°F)
    Final cure time and temperature: 7 days at 70°C (158°F)
    Special comments: Pre-heat coating and substrate to 120°F - 140°F (49°C - 60°C) prior to
    application. Maintain adequate air circulation and ventilation. During curing period
    atomized air drying system is highly recommended. Following application flush wash the
    pipe with running water for 10 hours.
[2] Only products bearing the NSF Mark on the product, product packaging, and/or
    documentation shipped with the product are Certified.

Facility : Kingman, AZ


Coatings - Fittings[1] [2] [LL]
   Royal PC-12
   Royal PC-327 

[1] Number of Coats: 1-3
    Maximum field use dry film thickness (in mils): 5
    Maximum thinner: 5% water by volume
    Recoat cure time and temperature: Immediately at 77°F
    Final cure time and temperature: 7 days at 77°F
    Special comments: 40-60% Solids.  The emulsion should be preheated to 120F° before
    application.  The substrate should be between 60°F and 180F° prior to coating.  Velocity
    of air flow across coating during cure: 400 linear feet per minute.  Flush wash the pipe
    until the water meets AWWA standards, or flush wash the pipe with running water for 10
    hours.
[2] Only products bearing the NSF Mark on the product, product packaging, and/or
    documentation shipped with the product are Certified.
[LL] Product conforms with lead content requirements for “lead free” plumbing as defined by
     California, Vermont, Maryland, and Louisiana state laws and the U.S. Safe Drinking Water
     Act.

Coatings - Pipe[1] [2] [LL]
   Royal PC-12
   Royal PC-327 

[1] Number of Coats: 1-3
    Maximum field use dry film thickness (in mils): 5
    Maximum thinner: 5% water by volume
    Recoat cure time and temperature: Immediately at 77°F
    Final cure time and temperature: 7 days at 77°F
    Special comments: 40-60% Solids.  The emulsion should be preheated to 120F° before
    application.  The substrate should be between 60°F and 180F° prior to coating.  Velocity
    of air flow across coating during cure: 400 linear feet per minute.  Flush wash the pipe
    until the water meets AWWA standards, or flush wash the pipe with running water for 10
    hours.
[2] Only products bearing the NSF Mark on the product, product packaging, and/or
    documentation shipped with the product are Certified.
[LL] Product conforms with lead content requirements for “lead free” plumbing as defined by
     California, Vermont, Maryland, and Louisiana state laws and the U.S. Safe Drinking Water
     Act.

Facility : Kimberton, PA


Coatings - Fittings[1] [2] [LL]
   Royal PC-12
   Royal PC-327 

[1] Number of Coats: 1-3
    Maximum field use dry film thickness (in mils): 5
    Maximum thinner: 5% water by volume
    Recoat cure time and temperature: Immediately at 77°F
    Final cure time and temperature: 7 days at 77°F
    Special comments: 40-60% Solids.  The emulsion should be preheated to 120F° before
    application.  The substrate should be between 60°F and 180F° prior to coating.  Velocity
    of air flow across coating during cure: 400 linear feet per minute.  Flush wash the pipe
    until the water meets AWWA standards, or flush wash the pipe with running water for 10
    hours.
[2] Only products bearing the NSF Mark on the product, product packaging, and/or
    documentation shipped with the product are Certified.
[LL] Product conforms with lead content requirements for “lead free” plumbing as defined by
     California, Vermont, Maryland, and Louisiana state laws and the U.S. Safe Drinking Water
     Act.

Coatings - Pipe[1] [2] [LL]
   Royal PC-12
   Royal PC-327 

[1] Number of Coats: 1-3
    Maximum field use dry film thickness (in mils): 5
    Maximum thinner: 5% water by volume
    Recoat cure time and temperature: Immediately at 77°F
    Final cure time and temperature: 7 days at 77°F
    Special comments: 40-60% Solids.  The emulsion should be preheated to 120F° before
    application.  The substrate should be between 60°F and 180F° prior to coating.  Velocity
    of air flow across coating during cure: 400 linear feet per minute.  Flush wash the pipe
    until the water meets AWWA standards, or flush wash the pipe with running water for 10
    hours.
[2] Only products bearing the NSF Mark on the product, product packaging, and/or
    documentation shipped with the product are Certified.
[LL] Product conforms with lead content requirements for “lead free” plumbing as defined by
     California, Vermont, Maryland, and Louisiana state laws and the U.S. Safe Drinking Water
     Act.
Number of matching Manufacturers is 1
Number of matching Products is 14
Processing time was 0 seconds