NSF Product and Service Listings

NSF Product and Service Listings

Did you know?

Connect with NSF

These NSF Official Listings are current as of Thursday, January 15, 2026 at 12:15 a.m. Eastern Time. Please contact NSF to confirm the status of any Listing, report errors, or make suggestions.

Alert: NSF is concerned about fraudulent downloading and manipulation of website text. Always confirm this information by clicking on the below link for the most accurate information: http://info.nsf.org/Certified/Plumbing/Listings.asp?Company=09000&Standard=014&

NSF/ANSI 14
Plastics Piping System Components and Related Materials

Click here for a list of End Use Code Designations.

Click on Product Standards or footnote in blue to view the referenced document

Charlotte Pipe & Foundry Company
Plastics Division
4210 Old Charlotte Highway
P.O. Box 1339
Monroe, NC 28111-1339
United States
704-291-3218
Visit this company's website

Facility : # 1 USA

Joining Materials

Product Type	General Material	For Use With	Trade Name	Product Standard
Solvent Cement+++ [1] [2] [3] [G]	CPVC	PW, DWV, SW	ChemDrain® One-Step CPVC Solvent Cement	ASTM F493
Solvent Cement# [1] [2] [3] [G]	CPVC	CW	ChemDrain® One-Step CPVC Solvent Cement	ASTM F2618
# Product has been Certified as part of the Charlotte Pipe ChemDrain System to ASTM F2618. +++ Material complies with NSF/ANSI/CAN 61 health effects requirements when tested at temperatures up to and including Commercial Hot (180° F). [1] This product was evaluated by NSF according to the requirements of NSF/ANSI/CAN 61, Section 4. [2] The compliance of this product with the health effect requirements of NSF/ANSI/CAN 61 was determined based on the testing of pipe and fittings assembled using the cement and either Weld-On® P-68®, P-70® Clear or Purple, or P-72 Clear Primers. [3] This product is acceptable for use with pipe and fittings sized 1/2" and greater diameter. [G] Product is Certified to NSF/ANSI/CAN 372 and conforms with the lead content requirements for "lead free" plumbing as defined by California, Vermont, Maryland, and Louisiana state laws and the U.S. Safe Drinking Water Act.

Facility : Huntsville, AL

Drain, Waste, and Vent - Pipe and Fittings

Product Type	Material Type	Trade Name	Product Standard
Fittings@ §	PVC	CPF®**	ASTM D2665
PVC 100 - Coupling (Hub x Hub)
1 1/4", 1 1/2", 2", 3", 4", 6", 8", 10", 12"
PVC 101 - Female Adapter (FPT x Hub)
1 1/4", 1 1/2", 2", 3", 4", 6", 8"
PVC 102 - Pipe Increaser-Reducer (Hub x Hub)
1 1/2"x2", 1 1/2"x3", 2"x3", 2"x4", 3"x4", 3"x6", 4"x6",4"x8", 4"x10", 4"x12"	6"x8", 6'x10", 6"x12", 8"x10", 8"x12", 10"x12"
PVC 103 - Trap Adapter-Male
1 1/2"	1 1/2" x 1 1/4"	2"
PVC 104 - Trap Adapter-Female (Hub x SLIP)
1 1/2"	1 1/2" x 1 1/4"	1 1/4"	2"
PVC 105 - Fitting Cleanout Adapter (SPG x FPT)
1 1/4", 1 1/2", 2", 3", 4", 6", 8"
PVC 105-X - Fitting Cleanout Adapter w/C.O. Plug
1 1/2", 2", 3", 4", 6", 8"
PVC 106 - Cleanout Plug (MPT)
1 1/2", 2", 3", 4", 6", 8", 10", 12"
PVC 107 - Flush Bushing (SPG x HUB)
1 1/2"x1 1/4", 2"x1 1/4", 2"x1 1/2", 3"x1 1/2", 3"x2", 4"x2"	4"x3", 6"x4", 8"x4", 8"x6", 10"x4", 10"x6", 10"x8", 12"x4", 12"x6", 12"x8"	12"x10"
PVC 108 - Flush Bushing{Cleanout Adapter}(SPGxFPT)
2" x 1 1/2, 8" x 6", 10" x 8", 12" x 8"
PVC 108X - Flush Bushing w/Plug
2" x 1 1/2", 10" x 8", 12" x 8"
PVC 109 - Male Adapter (Not accept a tail piece)
1 1/4", 1 1/4" x 1 1/2", 1 1/2", 1 1/2" x 1 1/4", 2", 3", 4"
PVC 110 - Flush C.O. Plug (MPT)
2", 3", 4"
PVC 111 - Male Adapter (SPG x MPT)
1 1/2"	1 1/2" x 1 1/4"	2"	3"
PVC 113 - Tray Pl Adp H
1 1/2"
PVC 116 - Cap (SOCKET)
1 1/2", 2", 3", 4", 6", 8", 10", 12"
PVC 117x - Adapter Coupling S&D Spigot/DWV Hub
4" x 3"
PVC 117–Adapter Coupling/Adapts S&D SPG to DWV SPG
3"	4" x 3", 4" x 4"
PVC 118 - Adapter Bushing
3", 4"
PVC 119 - No Hub Adapter (Slip x Hub)
1 1/2", 2", 2" x 1 1/2", 3", 4", 4" x 3"
PVC 122 - Spigot Adapter, Cast Iron (Hub x Hub)
2" x 2", 3" x 3", 4" x 4"
PVC 123 - Hub Adapter, Cast Iron (Hub x SPG)
2" x 2", 3" x 3", 4" x 4"
PVC 123-R-Hub Adapter,Cast Iron,Increaser(HubxSPG)
1 1/2" x 2", 3" x 4"
PVC 131 - Test Cap
1 1/2", 2", 3", 4"
PVC 300 - 1/4 Bend (Hub x Hub)
1 1/4", 1 1/2", 2", 3", 4", 6", 8", 10", 12"
PVC 300-R - 1/4 Bend, Reducing (Hub x Hub)
2" x 1 1/2"
PVC 302 - 1/4 Bend, Street (SPG x Hub)
1 1/4", 1 1/2", 2", 3", 4", 6", 8"
PVC 303 -1/4 Bend with Low Heel Inlet(HubxHubxHub)
3" x 3" x 1 1/2", 3" x 3" x 2", 4" x 4" x 2"
PVC 304 - Long Sweep 1/4 Bend (Hub x Hub)
1 1/2", 2", 3", 4", 6"
PVC 305 - Long Sweep 1/4 Bend W/High Heel Inlet
3" x 3" x 2"
PVC 307 - Long Sweep 1/4 Bend w/Low Heel Inlet
3" x 3" x 1 1/2"	3" x 3" x 2"
PVC 309 - Long Sweep 1/4 Bend, Street (Hub x SPG)
1 1/2", 2", 3", 4"
PVC 310–¼ Bend Street Low Heel Inlet (HubxSPGxHub)
3" x 3" x 2"
PVC 319 - 1/6 Bend (Hub x Hub)
1 1/2", 2", 3", 4"
PVC 320 - 1/6 Bend Street (Hub x SPG)
1 1/2", 2", 3", 4"
PVC 321 - 1/8 Bend (Hub x Hub)
1 1/4", 1 1/2", 2", 3", 4", 6", 8", 10", 12"
PVC 323 - 1/8 Bend, Street (SPG x Hub)
1 1/4", 1 1/2", 2", 3", 4", 6", 8", 10", 12"
PVC 324 - 1/16 Bend (Hub x Hub)
1 1/2", 2", 3", 4", 6", 8", 10", 12"
PVC 326 - 1/16 Bend, Street (SPG x Hub)
1 1/2", 2", 3", 4", 6", 8"
PVC 327 - Double 1/4 Bend (Hub x Hub x Hub)
1 1/2", 2", 3", 2 x 1 1/2" x 1 1/2"
PVC 329 - Closet Bend, Reducing (Hub x Hub)
3" x 4"
PVC 330 - Closet Bend, Reducing (Hub x SPG)
3" x 4"
PVC 330-X-Closet Bend,Reducing w/Test Cap(HubxSPG)
3" x 4"
PVC 331 - Vent Ell (Hub x Hub)
1 1/2", 2", 3"
PVC 333 - Vent Ell, Street (Hub x SPG)
1 1/2", 2", 3"
PVC 400 - Sanitary Tee (All Hub)
1 1/4", 1 1/2", 2", 3", 4", 6", 8", 10", 12"
PVC 401 - Sanitary Tee, Reducing (All Hub)
2" x 1 1/2" x 1 1/2"	2" x 1 1/2" x 2"	2" x 2" x 1 1/2"	3" x 3" x 1 1/2"
3" x 3" x 2"	4" x 4" x 1 1/2"	4" x 4" x 2"	4" x 4" x 3"
6" x 6" x 4"	8" x 8" x 4"	8" x 8" x 6"	10" x 10" x 8"
12" x 12" x 8"	12" x 12" x 10"
PVC 403 - Sanitary Tee, Street (SPG x Hub x Hub)
1 1/2", 2", 3", 4"
PVC 404 -Sanitary Tee,Street,Reducing(SPGxHubxHub)
2"x2"x1 1/2", 3"x3"x1 1/2", 3"x3"x2", 4"x4"x2"
PVC 416 - Sanitary Tee w/Left Side Inlet (All Hub)
3" x 3" x 3" x 1 1/2"	3" x 3" x 3" x 2"	4" x 4" x 4" x 2"
PVC 417 - Sanitary Tee w/Right Side Inlet(All Hub)
3" x 3" x 3" x 1 1/2"	3" x 3" x 3" x 2"	4" x 4" x 4" x 2"
PVC 418–Sanitary Tee Right & Left Side Inlet (Hub)
3" x 3" x 3" x 2" x 2", 4" x 4" x 4" x 2" x 2"
PVC 428 - Double Sanitary Tee (All Hub)
1 1/2", 2", 3", 4"
PVC 429 - Double Sanitary Tee, Reducing (All Hub)
2" x 2" x 1 1/2"x1 1/2"	3" x 3"x 1 1/2"x1 1/2"	3" x 3" x 2" x 2"	4" x 4" x 1 1/2" x 1 1/2"
4" x 4" x 2" x 2"	4" x 4" x 3" x 3"
PVC 431–Dbl Sanitary Tee, St, Red. SPGxHubxHubxHub
3" x 3" x 1 1/2" x 1 1/2"
PVC 438 - Dbl Sanitary Tee w/ Side Inlet (All Hub)
3" x 3" x 3" x 3" x 2", 4" x 4" x 4" x 4" x 2"
PVC 439 - Dbl San Tee w/ Right & Left Side Inlets
3" x 3" x 3" x 3" x 2" x 2", 4" x 4" x 4" x 4" x 2" x 2"
PVC 441 - Vent Tee (All Hub)
1 1/2", 2", 3", 4", 6", 8"
PVC 444-X - Cleanout Tee w/ Cleanout Plug(HubxHub)
1 1/2", 2", 3", 4", 6", 8", 6" x 6" x 4", 8" x 8" x 6"	10" x 10" x 8", 12" x 12" x 6", 12" x 12" x 8"
PVC 445 - Flush Cleanout Tee (Hub x Hub x FPT)
1 1/2", 2", 3", 4", 6", 8", 10" x 10" x 8", 12" x 12" x 8"
PVC 445-X - Flush Tee w/ Cleanout Plug (Hub x Hub)
1 1/2", 2", 3", 4"
PVC 448 - Two-Way Cleanout (All Hub)
3", 4", 6"
PVC 449 - Sanitary Tee (All Hub)
2"
PVC 500 - Double Fixture Fitting (All Hub)
2", 3", 2" x 1 1/2" x 1 1/2" x 1 1/2", 2" x 2" x 1 1/2" x 1 1/2"
PVC 501 – Comb. Wye & 1/8 Bend-One Piece (All Hub)
1 1/2", 2", 3", 4"
PVC 502 - Comb Wye & 1/8 Bend, Reducer (All Hub)
2" x 1 1/2" x 1 1/2"	2" x 1 1/2" x 2"	2" x 2" x 1 1/2"	3" x 3" x 1 1/2"
3" x 3" x 2"	4" x 4" x 2"	4" x 4" x 3"
PVC 503 - Combination Wye and 1/8 Bend (H x H x H)
6" x 6" x 6"	8" x 8" x 8"	12" x 12" x 12"
PVC 504–Comb. Wye & 1/8 Bend Red., Two Piece (Hub)
4” x 4" x 3"	6" x 6" x 3"	6" x 6" x 4"	8" x 8" x 4"
8" x 8" x 6"	10" x 10" x 4"	10" x 10" x 6"	10" x 10" x 8"
12" x 12" x 4"	12" x 12" x 6"	12" x 12" x 8"	12" x 12" x 10"
PVC 507 - Dbl Combination Wye & 1/8 Bend (ALL HUB)
1 1/2", 2", 3", 4"	2" x 2" x 1 1/2" x 1 1/2"	3" x 3" x 2" x 2"	4" x 4" x 2" x 2"
4" x 4" x 3" x 3"	6" x 6" x 4" x 4"
PVC 515 - Comb Wye & 1/8 Bend w/ Left Side Inlet
3" x 3" x 3" x 2"
PVC 516–Comb. Wye & 1/8 Bend Rgt Side Inlet (Hub)
3" x 3" x 3" x 2"
PVC 517–Comb. Wye & 1/8 Bend Rgt & Lft Inlet (Hub)
3" x 3" x 3" x 2" x 2"
PVC 600 - Wye (All Hub)
1 1/4", 1 1/2", 2" 3",4",6", 8", 10", 12"
PVC 601 - Wye, Reducing (All Hub)
2" x 1 1/2" x 1 1/2"	2" x 1 1/2" x 2"	2" x 2" x 1 1/2"	3" x 3" x 1 1/2"
3" x 3" x 2"	4" x 4" x 1 1/2"	4" x 4" x 2"	4" x 4" x 3"
6" x 6" x 3"	6" x 6" x 4"	8" x 8" x 4"	8" x 8" x 6"
10" x 10" x 4"	10" x 10" x 6"	10" x 10" x 8"	12" x 12" x 4"
12" x 12" x 6"	12" x 12" x 8"	12" x 12" x 10"
PVC 602 - Wye, Street (SPG x Hub x Hub)
1 1/2", 2", 3", 4"
PVC 603 - Wye, Street, Reducing (SPG x Hub x Hub)
3" x 3" x 1 1/2"	3" x 3" x 2"	4" x 4" x 2"	4" x 4" x 3"
PVC 611 - Double Wye (ALL HUB)
1 1/2", 2", 3", 4", 6"
PVC 612 - Double Wye, Reducing (ALL HUB)
2" x 2" x 1 1/2" x 1 1/2"	3" x 3" x 1 1/2" x 1 1/2"	3" x 3" x 2" x 2"	4" x 4" x 2" x 2"
4" x 4" x 3" x 3"	6" x 6" x 4" x 4"
PVC 700 - Return Bend (Hub x Hub)
1 1/2", 2", 3", 4"
PVC 703P - Tray Adapter
1 1/2" x 1 1/4"
PVC 703X - Tray Adapter
1 1/2" x 1 1/4"
PVC 704P - Tail Piece Adpt.(SxSLIP w/ Plastic Nut)
1 1/2"
PVC 704X - Tail Piece Adpt. (SxSLIP w/ Chrome Nut)
1 1/2"
PVC 706-X - P-Trap (Hub x Hub)
1 1/2", 2", 3", 4"
PVC 707-X - P-Trap with Cleanout (Hub x Hub)
1 1/2", 2", 3", 4"
PVC 708-P - P-Trap (Hub x Hub with Plastic Nut)
1 1/4", 1 1/2", 2"
PVC 708-X - P-Trap (Hub x Hub with Chrome Nut)
1 1/2"
PVC 709-X - P-Trap w/Cleanout(HubxHubw/Chrome Nut)
1 1/2"
PVC 710 - Low Profile P-Trap w/Solvent Weld Joint
2"
PVC 711-X - L.A. Pattern P-Trap
1 1/2"
PVC 711P - L.A. Pattern P-Trap (Slip x Hub)
1 1/2"
PVC 800 - Closet Flange (Hub)
4" x 3", 4" x 4"
PVC 800KO - Closet Flange with Knock Out (Hub)
4" x 3", 4" x 4"
PVC 800s - Closet Flange with Stop (Hub)
4" x 3"
PVC 801 - Closet Flange, Reducing (SPIGOT)
4" x 3"
PVC 810-KO-Closet Flange,Adj w/PlasRing w-KnockOut
4" x 3"
PVC 811-KO-Closet Flange,Adj w/Metal/Plastic Ring
4" x 3"
PVC 811–Closet Flange, Adj Metal/Plastics Ring-Hub
4" x 3", 4" x 4"
PVC 812-Closet Flange, Adj w/ Metal/Plastic Ring
4" x 3", 4" x 4"
PVC 815-Flush Closet Flange-fits 3" or 4" (Hub)
4" x 4"/4" x 3"
PVC 815K-Flush Closet Flange w-Knock Out (Hub)
4" x 3"	4" x 4"
PVC 820-Offset Flange,Adj
4" x 3"
PVC 820P - Offset Flange, Adj Plastic Ring
4" x 3"
PVC 900 - Swivel Tray Plug Adp. w/ Washer(SpgxFPT)
1 1/2"
PVC 910 - Swivel Tray Plug Adp. w/ Washer (HxFPT)
1 1/2"
@ A letter after the part number designates the following: X - Metal ring/plastic plug R - Reducing P - Plastic ring W - Washer § Product is Certified to the Uniform Plumbing Code™. Installation in accordance with the manufacturer's instructions and the requirements of the latest edition of the Uniform Plumbing Code™. ** These fittings products may also be represented by the trade names: Charlotte Pipe and Foundry Company®, Charlotte Plastics®, Charlotte Pipe®, Charlotte®, Chartlotte or Char®.
Fittings@	PVC	CPF®**	*SE 7992*
PVC 130 - Repair Coupling (Hub x Hub)
1 1/2", 2", 3", 4", 6"
@ A letter after the part number designates the following: X - Metal ring/plastic plug R - Reducing P - Plastic ring W - Washer ** These fittings products may also be represented by the trade names: Charlotte Pipe and Foundry Company®, Charlotte Plastics®, Charlotte Pipe®, Charlotte®, Chartlotte or Char®.

Potable Water - Pipe and Fittings

Product Type	Material Type	Trade Name	Product Standard
Pipe§ +++ [G]	CPVC 4120	Charlotte Pipe®*	ASTM D2846
1/4" - 2" SDR 11
* These pipe products may also be represented by the trade names: Charlotte Pipe®/Flowguard Gold®. § Product is Certified to the Uniform Plumbing Code™. Installation in accordance with the manufacturer's instructions and the requirements of the latest edition of the Uniform Plumbing Code™. +++ Material complies with NSF/ANSI/CAN 61 health effects requirements when tested at temperatures up to and including Commercial Hot (180° F). [G] Product is Certified to NSF/ANSI/CAN 372 and conforms with the lead content requirements for "lead free" plumbing as defined by California, Vermont, Maryland, and Louisiana state laws and the U.S. Safe Drinking Water Act.
Fittings+++ [G]	CPVC	CPF**	ASTM D2846
CTS 2100 Coupling
1/2"	3/4"	1"	1 1/4"
1 1/2"	2"	3/4" x 1/2"	1" x 3/4"
CTS x IPS 2100I Transition Coupling
3/4"	1"
CTS 2107 Reducer Bushing
3/4" x 1/2"	1" x 1/2"	1" x 3/4"	1 1/4" x 1/2"
1 1/4" x 3/4"	1 1/4" x 1"	1 1/2" x 1/2"	1 1/2" x 3/4"
1 1/2" x 1"	1 1/2" x 1 1/4"	2" x 1/2"	2" x 3/4"
2" x 1"	2" x 1 1/4"	2" x 1 1/2"
CTS 2116 CTS Cap
1/2"	3/4"	1"	1 1/4"
1 1/2"	2"
CTS 2300 90° Elbow, 1/4 Bend
1/2"	3/4"	1"	1 1/4"
1 1/2"	2"	3/4" x 1/2"
CTS 2300D Hub x Hub Drop Ear Elbow
1/2"
CTS 2304 90° Street Elbow
1/2"	3/4"	1"
CTS 2309 45° Elbow, 1/8 Bend
1/2"	3/4"	1"	1 1/4"
1 1/2"	2"
CTS 2310 45° Street Elbow
1/2"	3/4"	1"	1 1/4"
1 1/2"	2"
CTS 2400 Reducer Tee
1/2" x 1/2" x 3/4"	3/4" x 3/4" x 1"	3/4" x 1/2" x 1/2"	3/4" x 1/2" x 3/4"
3/4" x 3/4" x 1/2"	1" x 1/2" x 1/2"	1" x 1/2" x 3/4"	1" x 1/2" x 1"
1" x 3/4" x 1/2"	1" x 3/4" x 3/4"	1" x 3/4" x 1"	1" x 1" x 1/2"
1" x 1" x 3/4"	1 1/4" x 1" x 1"	1 1/4" x 1 1/4" x 1/2"	1 1/4" x 1 1/4" x 3/4"
1 1/4" x 1 1/4" x 1"	1 1/2" x 1" x 1"	1 1/2" x 1 1/2" x 1/2"	1 1/2" x 1 1/2" x 1"
1 1/2" x 1 1/2" x 3/4"	2" x 2" x 3/4"	2" x 2" x 1/2"	2" x 2" X 1"
2" x 2" x 1 1/2"
CTS 2400 Tee
1/2"	3/4"	1"	1 1/4"
1 1/2"	2"
CTS 2500 Spigot Adapter Trans. Union
1/2"	3/4"
CTS x IPS 2107I Transition Bushing
1/2"	3/4"	1"	1 1/4"
1 1/2"	2"
** These fitting products may also be represented by the trade names: CP&F, Charlotte, Charlotte Pipe, and Charlotte Pipe and Foundry. +++ Material complies with NSF/ANSI/CAN 61 health effects requirements when tested at temperatures up to and including Commercial Hot (180° F). [G] Product is Certified to NSF/ANSI/CAN 372 and conforms with the lead content requirements for "lead free" plumbing as defined by California, Vermont, Maryland, and Louisiana state laws and the U.S. Safe Drinking Water Act.
Fittings+ [G]	PVC	Charlotte Pipe & Foundry, CP&F, or Charlotte	ASTM D2466
PVC 2100 Coupling (Hub x Hub)(429-xxx)
1/2"	3/4"	1"	1 1/4"
1 1/2"	2"	2 1/2"	3"
4"	6"	8"	10"
12"	3/4" x 1/2"	1" x 3/4"
PVC 2100D (Deep Socket) Cplg (Hub x Hub) (479-XXX)
1/2"	3/4"	1"	1 1/4"
1 1/2"	2"
PVC 2101 Female Adapter (Hub x FPT)(435-xxx)
1/2"	3/4"	1"	1 1/4"
1 1/2"	2"	2 1/2"	3"
4"
PVC 2101 Female Adapter Reducing(HubxFPT)(435-xxx)
3/4" x 1/2"	3/4" x 1"	1" x 3/4"
PVC 2101S Female Adp Red (FPT x RS)
3/4" x 1/2"
PVC 2102 Coupling (FPT x FPT) (430-xxx)
1/2"	3/4"	1"
PVC 2103 Riser Extension (MPT x FPT) (439-xxx)
1/2" x 1/2"	3/4" x 3/4"
PVC 2104 Female Adaptor (Hub x FPT)
1/2" x 3/4"	3/4" x 1/2"
PVC 2107 Reducing Bushing (SPG x S)(437-xxx)
3/4" x 1/2"	1" x 1/2"	1" x 3/4"	1 1/4" x 1/2"
1 1/4" x 3/4"	1 1/4" x 1"	1 1/2" x 1/2"	1 1/2" x 3/4"
1 1/2" x 1"	1 1/2" x 1 1/4"	2" x 1/2"	2" x 3/4"
2" x 1"	2" x 1 1/4"	2" x 1 1/2"	2 1/2" x 2"
3" x 1 1/2"	3" x 2"	3" x 2 1/2"	4" x 2"
4" x 3"	6" x 4"	8" x 4"	8" x 6"
PVC 2108 Reducing Bushing (SPG x FPT)(438-xxx)
3/4" x 1/2"	1" x 1/2"	1" x 3/4"	1 1/4" x 1/2"
1 1/4" x 3/4"	1 1/4" x 1"	1 1/2" x 1/2"	1 1/2" x 3/4"
1 1/2" x 1"	1 1/2" x 1 1/4"	2" x 1/2"	2" x 3/4"
2" x 1"	2" x 1 1/4"	2" x 1 1/2"	3" x 2"
3" x 2 1/2"	4" x 2"	4" x 3"	6" x 4"
PVC 2109 Male Adapter (MPT x S) (436-xxx)
1/2"	3/4"	1"	1 1/4"
1 1/2"	2"	2 1/2"	3"
4"	6"
PVC 2110 Male Adapter Reducing(MPT x Hub)(436-xxx)
1/2" x 3/4"	3/4" x 1/2"	3/4" x 1"	1" x 3/4"
1" x 1 1/4"	1 1/4" x 1"	1 1/4" x 1 1/2"	1 1/2" x 1 1/4"
1 1/2" x 2"	2" x 1 1/2"
PVC 2112 Reducing Bushing (MPT x FPT) (439-xxx)
3/4" x 1/2"	1 x 1/2"	1" x 3/4"	1 1/4" x 1/2"
1 1/4" x 3/4"	1 1/4" x 1"	1 1/2" x 1/2"	1 1/2" x 3/4"
1 1/2" x 1"	1 1/2" x 1 1/4"	2" x 1"	2 x 1 1/4"
2" x 1 1/2"
PVC 2113 Plug (MPT)(450-xxx)
1 1/2"	1 1/4"	3/4"	1/2"
2"	1"
PVC 2116 Cap (Hub) (447-xxx)
1 1/4"	1/2"	3/4"	1"
1 1/2"	2"	2 1/2"	3"
4"	6"	8"
PVC 2117 Cap (FPT)(448-xxx)
1/2"	3/4"	1"	1 1/4"
1 1/2"	2"
PVC 2118 Plug (SPG)(449-xxx)
1/2"	3/4"	1"	1 1/4"
1 1/2"	2"
PVC 2300 90° Elbow (Hub x Hub)(406-xxx)
1/2"	3/4"	1"	1 1/4"
1 1/2"	2"	2 1/2"	3"
4"	6"	8"
PVC 2300 90° Reducing Elbow (Hub x Hub)(406-xxx)
3/4" x 1/2"	1" x 1/2"	1" x 3/4"	1 1/4" x 1"
1 1/2" x 1"
PVC 2301 90° Elbow (Hub x FPT)(407-xxx)
1/2"	3/4"	1"	1 1/4"
1 1/2"	2"
PVC 2301 90° Reducing Elbow (Hub x FPT)(407-xxx)
3/4" x 1/2"	1/2" x 3/4"	1" x 1/2"	1" x 3/4"
PVC 2302 90° Elbow (FPT x FPT)(408-xxx)
1/2"	3/4"	1"	1 1/4"
1 1/2"	2"
PVC 2304 90° Elbow (SPG x Hub)(409-xxx)
1/2"	3/4"	1"	1 1/4"
1 1/2"	2"
PVC 2306 90° Elbow (MPT x Hub)(410-xxx)
1/2"	3/4"	3/4" x 1/2"	1"
1 1/4"	1 1/2"	2"
PVC 2307 90° Elbow (MPT x FPT)(412-xxx)
1/2"	3/4"	1"	1 1/4"
1 1/2"	2"
PVC 2309 45° Elbow (Hub x Hub)(417-xxx)
1/2"	3/4"	1"	1 1/4"
1 1/2"	2"	2 1/2"	3"
4"	6"	8"
PVC 2310 Elbow (Socket x SPG)
2"
PVC 2400 Reducing Tee (All Hub)(401-xxx)
1/2" x 1/2" x 3/4"	3/4” x ½” x 1/2”	3/4" x 3/4" x 1/2"	3/4" x 3/4" x 1"
1" x 3/4" x 1/2"	1" x 3/4" x 3/4"	1" x 3/4" x 1"	1" x 1" x 1/2"
1" x 1" x 3/4"	1" x 1" x 1 1/4"	1" x 1" x 1 1/2"	1 1/4" x 1" x 1/2"
1 1/4" x 1" x 3/4"	1 1/4" x 1" x 1"	1 1/4" x 1 1/4" x 1/2"	1 1/4" x 1 1/4" x 3/4"
1 1/4" x 1 1/4" x 1"	1 1/2" x 1 1/4" x 1/2"	1 1/2" x 1 1/2" x 1/2"	1 1/2" x 1 1/2" x 3/4"
1 1/2" x 1 1/2" x 1"	1 1/2" x 1 1/2" x 1 1/4"	1 1/2" x 1 1/2" x 2"	2" x 1 1/2" x 1 1/2"
2" x 2" x 1/2"	2" x 2" x 3/4"	2" x 2" x 1"	2" x 2" x 1 1/4"
2" x 2" x 1 1/2"	2 1/2" x 2 1/2" x 3/4"	2 1/2" x 2 1/2" x 1"	2 1/2" x 2 1/2" x 2"
2 1/2" x 2 1/2" x 1 1/2"	2 1/2" x 2 1/2" x 1 1/4"	3" x 3" x 1"	3" x 3" x 1/2"
3" x 3" x 3/4"	3" x 3" x 1 1/4"	3" x 3" x 1 1/2"	3" x 3" x 2"
4" x 4" x 3/4"	4" x 4" x 1 1/4"	4" x 4" x 1 1/2"	4" x 4" x 1"
4" x 4" x 2"	4" x 4" x 3"	6" x 6" x 4"
PVC 2400 Tee (All Hub)(401-xxx)
1/2"	3/4"	1"	1 1/4"
1 1/2"	2"	2 1/2"	3"
4"	6"	8"
PVC 2401 Reducing Tee (Hub x Hub x FPT)(402-xxx)
3/4" x 3/4" x 1/2"	1" x 1" x 1/2"	1" x 1" x 3/4"	1 1/4" x 1 1/4" x 1/2"
1 1/4" x 1 1/4" x 3/4"	1 1/4" x 1 1/4" x 1"	1 1/2" x 1 1/2" x 1/2"	1 1/2" x 1 1/2" x 3/4"
1 1/2" x 1 1/2" x 1"	2" x 2" x 1"	2" x 2" x 1/2"	2" x 2" x 3/4"
2" x 2" x 1 1/2"	2 1/2" x 2 1/2" x 1 1/2"	2 1/2" x 2 1/2" x 3/4"
PVC 2401 Tee (Hub xHub xFPT)(402-xxx)
1/2"	3/4"	1"	1 1/4"
1 1/2"	2"
PVC 2402 Tee (FPT x FPT x FPT) (405-XXX)
1/2"	3/4"	1"	1 1/2"
PVC 2410 Cross (All Hub)(420-xxx)
1/2"	3/4"	1"	1 1/4"
1 1/2"	2"
PVC 2510 – Side Outlet Elbow (All Hub)
1/2" x 1/2" x 1/2"	3/4" x 3/4" x 3/4"	1" x 1" x 1"	2"
PVC 2520 90° Elbow-S/OUT(Hub x Hub x FPT)(414-xxx)
1/2"	3/4" x 3/4" x 1/2"	1" x 1" x 1/2"
+ Material complies with NSF/ANSI/CAN 61 health effects requirements when tested at 73° F. [G] Product is Certified to NSF/ANSI/CAN 372 and conforms with the lead content requirements for "lead free" plumbing as defined by California, Vermont, Maryland, and Louisiana state laws and the U.S. Safe Drinking Water Act.
Fittings+ [G]	PVC	Charlotte Pipe & Foundry, CP&F, or Charlotte	ASTM D2609
PVC 2111 Insert Adapters
3/4"	1"	1 1/2"
+ Material complies with NSF/ANSI/CAN 61 health effects requirements when tested at 73° F. [G] Product is Certified to NSF/ANSI/CAN 372 and conforms with the lead content requirements for "lead free" plumbing as defined by California, Vermont, Maryland, and Louisiana state laws and the U.S. Safe Drinking Water Act.

Facility : Wildwood, FL

Drain, Waste, and Vent - Pipe and Fittings

Product Type	Material Type	Trade Name	Product Standard
Pipe §*	PVC	Charlotte Pipe®***	ASTM D2665
1 1/4" - 8" Sch 40
* Sockets and gasketed bell ends are not tested or Listed by NSF for this production facility. § Product is Certified to the Uniform Plumbing Code™. Installation in accordance with the manufacturer's instructions and the requirements of the latest edition of the Uniform Plumbing Code™. *** These pipe products may include the production location code PLFL in the trade name.
Pipe §*	PVC	Charlotte Pipe®***	ASTM F891
1 1/4" - 8" Sch 40
* Sockets and gasketed bell ends are not tested or Listed by NSF for this production facility. § Product is Certified to the Uniform Plumbing Code™. Installation in accordance with the manufacturer's instructions and the requirements of the latest edition of the Uniform Plumbing Code™. *** These pipe products may include the production location code PLFL in the trade name.

Potable Water - Pipe and Fittings

Product Type	Material Type	Trade Name	Product Standard
Pipe + § [G]*	PVC	Charlotte Pipe®***	ASTM D1785
1/8" - 8" Sch 40
1/2" - 8" Sch 80
* Sockets and gasketed bell ends are not tested or Listed by NSF for this production facility. + Material complies with NSF/ANSI/CAN 61 health effects requirements when tested at 73° F. § Product is Certified to the Uniform Plumbing Code™. Installation in accordance with the manufacturer's instructions and the requirements of the latest edition of the Uniform Plumbing Code™. *** These pipe products may include the production location code PLFL in the trade name. [G] Product is Certified to NSF/ANSI/CAN 372 and conforms with the lead content requirements for "lead free" plumbing as defined by California, Vermont, Maryland, and Louisiana state laws and the U.S. Safe Drinking Water Act.
Pipe + § [G]*	PVC	Charlotte Pipe®***	ASTM D2241
1/2" SDR 13.5
3/4" - 18" SDR 21
1" - 6" SDR 26
2 1/2" - 12" SDR 32.5
4" - 12" SDR 41
* Sockets and gasketed bell ends are not tested or Listed by NSF for this production facility. + Material complies with NSF/ANSI/CAN 61 health effects requirements when tested at 73° F. § Product is Certified to the Uniform Plumbing Code™. Installation in accordance with the manufacturer's instructions and the requirements of the latest edition of the Uniform Plumbing Code™. *** These pipe products may include the production location code PLFL in the trade name. [G] Product is Certified to NSF/ANSI/CAN 372 and conforms with the lead content requirements for "lead free" plumbing as defined by California, Vermont, Maryland, and Louisiana state laws and the U.S. Safe Drinking Water Act.

Reclaimed Water - Pipe and Fittings

Product Type	Material Type	Trade Name	Product Standard
Pipe §*	PVC	Charlotte Pipe®***	ASTM D1785
3/4" - 6" Sch 40
* Sockets and gasketed bell ends are not tested or Listed by NSF for this production facility. § Product is Certified to the Uniform Plumbing Code™. Installation in accordance with the manufacturer's instructions and the requirements of the latest edition of the Uniform Plumbing Code™. *** These pipe products may include the production location code PLFL in the trade name.
Pipe §*	PVC	Charlotte Pipe®***	ASTM D2241
3/4" - 6" SDR 21
2 1/2" - 12" SDR 32.5
4" - 12" SDR 41
* Sockets and gasketed bell ends are not tested or Listed by NSF for this production facility. § Product is Certified to the Uniform Plumbing Code™. Installation in accordance with the manufacturer's instructions and the requirements of the latest edition of the Uniform Plumbing Code™. *** These pipe products may include the production location code PLFL in the trade name.

Well Casings

Facility : Maize, KS

Drain, Waste, and Vent - Pipe and Fittings

Product Type	Material Type	Trade Name	Product Standard
Pipe §*	PVC	Charlotte Pipe®***	ASTM D2665
1 1/4" - 12" Sch 40
* Sockets and gasketed bell ends are not tested or Listed by NSF for this production facility. § Product is Certified to the Uniform Plumbing Code™. Installation in accordance with the manufacturer's instructions and the requirements of the latest edition of the Uniform Plumbing Code™. *** These pipe products may include the production location code PLKS in the trade name.
Pipe§	PVC	Charlotte Pipe®***	ASTM F891
1 1/2" - 12" Sch 40
§ Product is Certified to the Uniform Plumbing Code™. Installation in accordance with the manufacturer's instructions and the requirements of the latest edition of the Uniform Plumbing Code™. *** These pipe products may include the production location code PLKS in the trade name.

Potable Water - Pipe and Fittings

Product Type	Material Type	Trade Name	Product Standard
Pipe § [G]*	PVC	Charlotte Pipe®***	ASTM D1785
1/2" - 8" Sch 80
1/2" - 12" Sch 40
* Sockets and gasketed bell ends are not tested or Listed by NSF for this production facility. § Product is Certified to the Uniform Plumbing Code™. Installation in accordance with the manufacturer's instructions and the requirements of the latest edition of the Uniform Plumbing Code™. *** These pipe products may include the production location code PLKS in the trade name. [G] Product is Certified to NSF/ANSI/CAN 372 and conforms with the lead content requirements for "lead free" plumbing as defined by California, Vermont, Maryland, and Louisiana state laws and the U.S. Safe Drinking Water Act.
Pipe § [G]*	PVC	Charlotte Pipe®***	ASTM D2241
1/2" SDR 13.5
3/4" - 2" SDR 21
1" - 6" SDR 26
2 1/2" - 12" SDR 32.5
4" - 12" SDR 41
* Sockets and gasketed bell ends are not tested or Listed by NSF for this production facility. § Product is Certified to the Uniform Plumbing Code™. Installation in accordance with the manufacturer's instructions and the requirements of the latest edition of the Uniform Plumbing Code™. *** These pipe products may include the production location code PLKS in the trade name. [G] Product is Certified to NSF/ANSI/CAN 372 and conforms with the lead content requirements for "lead free" plumbing as defined by California, Vermont, Maryland, and Louisiana state laws and the U.S. Safe Drinking Water Act.

Well Casings

Product Type	Material Type	Trade Name	Product Standard
Well Casings+ [G]	PVC	Charlotte Pipe®***	ASTM F480
2" - 12" Sch 40
+ Material complies with NSF/ANSI/CAN 61 health effects requirements when tested at 73° F. *** These pipe products may include the production location code PLKS in the trade name. [G] Product is Certified to NSF/ANSI/CAN 372 and conforms with the lead content requirements for "lead free" plumbing as defined by California, Vermont, Maryland, and Louisiana state laws and the U.S. Safe Drinking Water Act.

Facility : Monroe, NC

Corrosive Waste - Pipe and Fittings

Product Type	Material Type	Trade Name	Product Standard
Fittings# Þ	CPVC	Charlotte Pipe ChemDrain®^	ASTM F2618
AW 100 Coupling
1 1/2"	2"	3"	4"
6"	8"
AW 101 Female Adapter
1 1/2"	2"	3"	4"
6"
AW 102 Pipe Increaser Reducer
1 1/2" x 2"	1 1/2" x 3"	2" x 3"	2" x 4"
3" x 4"	3" x 6"	4" x 6"
AW 103 Male Trap Adapter
1 1/2"	2"
AW 103P Male Trap Adapter w/ Plastic Ring
1 1/2"	2"
AW 103X Male Trap Adapter w/ Metal Ring
1 1/2"	2"
AW 105 Fitting Cleanout Adapter
1 1/2"	2"	3"	4"
6"	8"
AW 105X Fitting Cleanout Adapter w/ CO
1 1/2"	2"	3"	4"
6"	8"
AW 106 Cleanout Plug
1 1/2"	2"	3"	4"
6"	8"
AW 107 Flush Bushing
2" x 1 1/2"	3" x 1 1/2"	3" x 2"	4" x 2"
4" x 3"	6" x 3"	6" x 4"	8" x 4"
8" x 6"
AW 109 Male Adapter
1 1/2"	2"	3"	4"
6"
AW 110 Cleanout Plug
1 1/2"	2"	3"	4"
6"
AW 116 Cap Socket
1 1/2"	2"	3"	4"
6"	8"
AW 1506 CPVC Tail Piece
1 1/2" x 6"
AW 1506P CPVC Tail Piece w/ Nut
1 1/2" - 6"
AW 1512 CPVC Tail Piece
1 1/2" x 12"
AW 1512P CPVC Tail Piece w/ Nut
1 1/2" x 12"
AW 1514P CPVC Tail Piece w/ Nut
1 1/2" x 14"
AW 300 1/4 Bend
1 1/2"	2"	3"	4"
6"	8"
AW 302 1/4 Bend Street
1 1/2"	2"	3"	4"
6"	8"
AW 304 Long Sweep 1/4 Bend
1 1/2"	2"	3"	4"
6"
AW 309 Long Sweep 1/4 Bend Street
1 1/2"	2"	3"	4"
6"
AW 319 1/4 Vent Ell Street
1 1/2"	2"	3"	4"
AW 319 1/6 Bend
1 1/2"	2"	3"	4"
6"
AW 320 1/6 Bend Street
1 1/2"	2"	3"	4"
AW 321 1/8 Bend
1 1/2"	2"	3"	4"
6"	8"
AW 323 1/8 Bend Street
1 1/2"	2"	3"	4"
6"	8"
AW 324 1/16 Bend
1 1/2"	2"	3"	4"
6"	8"
AW 326 1/16 Bend Street
1 1/2"	2"	3"	4"
6"	8"
AW 327 Double 1/4 Bend
1 1/2"	2"	3"
AW 331 1/4 Vent Ell
1 1/2"	2"	3"	4"
6"
AW 333 1/4 Bend Vent Street
1 1/2"	2"	3"	4"
AW 400 Sanitary Tee
1 1/2"	2"	3"	4"
6"	8"
AW 401 Sanitary Tee Reducing
2" x 1 1/2" x 1 1/2"	2" x 2" x 1 1/2"	2" x 1 1/2" x 2"	3" x 3" x 1 1/2"
3" x 3" x 2"	4" x 4" x 2"	4" x 4" x 3"	6" x 6" x 4"
8" x 8" x 4"
AW 404 Sanitary Tee Reducing, Street
1 1/2"	2"	3"
AW 428 Double Sanitary Tee
1 1/2"	2"	3"	4"
AW 429 Double Sanitary Tee Reducing
2" x 2" x 1 1/2" x 1 1/2"	3" x 3" x 1 1/2" x 1 1/2"	3" x 3" x 2" x 2"	4" x 4" x 1 1/2" x 1 1/2"
4" x 4" x 2" x 2"	4" x 4" x 3" x 3"
AW 441 Vent Tee
1 1/2"	2"	3"	4"
AW 444X Cleanout Tee w/ Plug
1 1/2"	2"	3"	4"
6"
AW 445 Flush Cleanout Tee
1 1/2"	2"	3"	4"
6"
AW 445X Flush C/O Tee w/ Cleanout Plug
1 1/2"	2"	3"	4"
6"
AW 500 Double Fixture Fitting
1 1/2"	2"	3"
AW 501 Combination Wye & 1/8 Bend
1 1/2"	2"	3"	4"
AW 502 Combo Wye & 1/8 Bend, Rdcing (1 Piece), Hub
2" x 1 1/2" x 1 1/2"	2" x 2" x 1 1/2"	3" x 3" x 1 1/2"	3" x 3" x 2"
4" x 4" x 2"	4" x 4" x 3"
AW 503 Combination Wye & 1/8 Bend
2"	3"	4"	6"
8"
AW 504 Combination Wye & 1/8 Bend, Reducing 2 Pcs
6" x 6" x 3"	6" x 6" x 4"
AW 504 Combo Wye 1/8 Bend Non-Reducing 2 Pcs
1 1/2"	2"	3"	4"
6"	6" x 6" x 3"	6" x 6" x 4"	8"
AW 507 Dble Combo Wye 1/8 Bend Non-Reducing, Fabr.
1 1/2"	2"	3"	4"
6"
AW 507 Double Combo Wye & 1/8 Bend, Reducing
2" x 2" x 1 1/2" x 1 1/2"	3" x 3" x 2" x 2"	4" x 4" x 2" x 2"	4" x 4" x 3" x 3"
6" x 6" x 3" x 3"	6" x 6" x 4" x 4"
AW 600 Wye
1 1/2"	2"	3"	4"
6"	8"
AW 601 Reducing Wye
2" x 1 1/2" x 1 1/2"	2" x 2" x 1 1/2"	3" x 3" x 1 1/2"	3" x 3" x 2"
4" x 4" x 1 1/2"	4" x 4" x 2"	4" x 4" x 3"	6" x 6" x 3"
6" x 6" x 4"	8" x 8" x 4"	8" x 8" x 6"
AW 611 Double Wye
1 1/2"	2"	3"	4"
6"
AW 612 Double Wye Reducing
2" x 2" x 1 1/2" x 1 1/2"	3" x 3" x 2" x 2"	4" x 4" x 2" x 2"	4" x 4" x 3" x 3"
6" x 6" x 4" x 4"
AW 700 Return Bend
1 1/2"	2"	3"	4"
6"
AW 705 S-Trap
1 1/2"	2"	3"	4"
AW 705R Running Trap
1 1/2"	2"	3"	4"
6"
AW 706X P-Trap w/ Solvent Weld Joint
1 1/2"	2"	3"	4"
6"
AW 707X P-Trap w/ Solvent Weld Joint & Clean Out
1 1/2"	2"
AW 708P P-Trap w/ Union
1 1/2"	2"
AW 711P LA P-Trap w/ Union
1 1/2"
AW 712 Jar Trap
1 1/2"
AW 712 P Jar Trap with Tail Piece Adapter
1 1/2"
AW 8530 Van Stone Flange
8"	1 1/2"	2"	3"
4"	6"
# Charlotte Pipe ChemDrain Pipe and Fittings have been Certified as a system with the Charlotte Pipe ChemDrain One-Step CPVC Solvent Cement to ASTM F2618. ^ These fitting products are also represented by the trade names: Charlotte Pipe and Foundry Company®, Charlotte®, Charlotte Pipe®, and ChemDrain Corrosive Waste Drainage System. Þ Product is Certified to the International Plumbing Code. Installation in accordance with the manufacturer's instructions and the requirements of the latest edition of the International Plumbing Code.
Fittings# Þ	CPVC	Charlotte Pipe ChemDrain®^	CSA B181.3
AW 100 Coupling
1 1/2"	2"	3"	4"
6"	8"
AW 101 Female Adapter
1 1/2"	2"	3"	4"
6"
AW 102 Pipe Increaser Reducer
1 1/2" x 2"	1 1/2" x 3"	2" x 3"	2" x 4"
3" x 4"	3" x 6"	4" x 6"
AW 103 Male Trap Adapter
1 1/2"	2"
AW 103P Male Trap Adapter w/ Plastic Ring
1 1/2"	2"
AW 103X Male Trap Adapter w/ Metal Ring
1 1/2"	2"
AW 105 Fitting Cleanout Adapter
1 1/2"	2"	3"	4"
6"	8"
AW 105X Fitting Cleanout Adapter w/ CO
1 1/2"	2"	3"	4"
6"	8"
AW 106 Cleanout Plug
1 1/2"	2"	3"	4"
6"	8"
AW 107 Flush Bushing
2" x 1 1/2"	3" x 1 1/2"	3" x 2"	4" x 2"
4" x 3"	6" x 3"	6" x 4"	8" x 4"
8" x 6"
AW 109 Male Adapter
1 1/2"	2"	3"	4"
6"
AW 110 Cleanout Plug
1 1/2"	2"	3"	4"
6"
AW 116 Cap Socket
1 1/2"	2"	3"	4"
6"	8"
AW 1506 CPVC Tail Piece
1 1/2" x 6"
AW 1506P CPVC Tail Piece w/ Nut
1 1/2" - 6"
AW 1512 CPVC Tail Piece
1 1/2" x 12"
AW 1512P CPVC Tail Piece w/ Nut
1 1/2" x 12"
AW 1514P CPVC Tail Piece w/ Nut
1 1/2" x 14"
AW 300 1/4 Bend
1 1/2"	2"	3"	4"
6"	8"
AW 302 1/4 Bend Street
1 1/2"	2"	3"	4"
6"	8"
AW 304 Long Sweep 1/4 Bend
1 1/2"	2"	3"	4"
6"
AW 309 Long Sweep 1/4 Bend Street
1 1/2"	2"	3"	4"
6"
AW 319 1/4 Vent Ell Street
1 1/2"	2"	3"	4"
AW 319 1/6 Bend
1 1/2"	2"	3"	4"
6"
AW 320 1/6 Bend Street
1 1/2"	2"	3"	4"
AW 321 1/8 Bend
1 1/2"	2"	3"	4"
6"	8"
AW 323 1/8 Bend Street
1 1/2"	2"	3"	4"
6"	8"
AW 324 1/16 Bend
1 1/2"	2"	3"	4"
6"	8"
AW 326 1/16 Bend Street
1 1/2"	2"	3"	4"
6"	8"
AW 327 Double 1/4 Bend
1 1/2"	2"	3"
AW 331 1/4 Vent Ell
1 1/2"	2"	3"	4"
6"
AW 333 1/4 Bend Vent Street
1 1/2"	2"	3"	4"
AW 400 Sanitary Tee
1 1/2"	2"	3"	4"
6"	8"
AW 401 Sanitary Tee Reducing
2" x 1 1/2" x 1 1/2"	2" x 2" x 1 1/2"	2" x 1 1/2" x 2"	3" x 3" x 1 1/2"
3" x 3" x 2"	4" x 4" x 2"	4" x 4" x 3"	6" x 6" x 4"
8" x 8" x 4"
AW 404 Sanitary Tee Reducing, Street
1 1/2"	2"	3"
AW 428 Double Sanitary Tee
1 1/2"	2"	3"	4"
AW 429 Double Sanitary Tee Reducing
2" x 2" x 1 1/2" x 1 1/2"	3" x 3" x 1 1/2" x 1 1/2"	3" x 3" x 2" x 2"	4" x 4" x 1 1/2" x 1 1/2"
4" x 4" x 2" x 2"	4" x 4" x 3" x 3"
AW 441 Vent Tee
1 1/2"	2"	3"	4"
AW 444X Cleanout Tee w/ Plug
1 1/2"	2"	3"	4"
6"
AW 445 Flush Cleanout Tee
1 1/2"	2"	3"	4"
6"
AW 445X Flush C/O Tee w/ Cleanout Plug
1 1/2"	2"	3"	4"
6"
AW 500 Double Fixture Fitting
1 1/2"	2"	3"
AW 501 Combination Wye & 1/8 Bend
1 1/2"	2"	3"	4"
AW 502 Combo Wye & 1/8 Bend, Rdcing (1 Piece), Hub
2" x 1 1/2" x 1 1/2"	2" x 2" x 1 1/2"	3" x 3" x 1 1/2"	3" x 3" x 2"
4" x 4" x 2"	4" x 4" x 3"
AW 503 Combination Wye & 1/8 Bend
2"	3"	4"	6"
8"
AW 504 Combination Wye & 1/8 Bend, Reducing 2 Pcs
6" x 6" x 3"	6" x 6" x 4"
AW 504 Combo Wye 1/8 Bend Non-Reducing 2 Pcs
1 1/2"	2"	3"	4"
6"	6" x 6" x 3"	6" x 6" x 4"	8"
AW 507 Dble Combo Wye 1/8 Bend Non-Reducing, Fabr.
1 1/2"	2"	3"	4"
6"
AW 507 Double Combo Wye & 1/8 Bend, Reducing
2" x 2" x 1 1/2" x 1 1/2"	3" x 3" x 2" x 2"	4" x 4" x 2" x 2"	4" x 4" x 3" x 3"
6" x 6" x 3" x 3"	6" x 6" x 4" x 4"
AW 600 Wye
1 1/2"	2"	3"	4"
6"	8"
AW 601 Reducing Wye
2" x 1 1/2" x 1 1/2"	2" x 2" x 1 1/2"	3" x 3" x 1 1/2"	3" x 3" x 2"
4" x 4" x 1 1/2"	4" x 4" x 2"	4" x 4" x 3"	6" x 6" x 3"
6" x 6" x 4"	8" x 8" x 4"	8" x 8" x 6"
AW 611 Double Wye
1 1/2"	2"	3"	4"
6"
AW 612 Double Wye Reducing
2" x 2" x 1 1/2" x 1 1/2"	3" x 3" x 2" x 2"	4" x 4" x 2" x 2"	4" x 4" x 3" x 3"
6" x 6" x 4" x 4"
AW 700 Return Bend
1 1/2"	2"	3"	4"
6"
AW 705 S-Trap
1 1/2"	2"	3"	4"
AW 705R Running Trap
1 1/2"	2"	3"	4"
6"
AW 706X P-Trap w/ Solvent Weld Joint
1 1/2"	2"	3"	4"
6"
AW 707X P-Trap w/ Solvent Weld Joint & Clean Out
1 1/2"	2"
AW 708P P-Trap w/ Union
1 1/2"	2"
AW 711P LA P-Trap w/ Union
1 1/2"
AW 712 Jar Trap
1 1/2"
AW 712 P Jar Trap with Tail Piece Adapter
1 1/2"
AW 8530 Van Stone Flange
8"	1 1/2"	2"	3"
4"	6"
# Charlotte Pipe ChemDrain Pipe and Fittings have been Certified as a system with the Charlotte Pipe ChemDrain One-Step CPVC Solvent Cement to ASTM F2618. ^ These fitting products are also represented by the trade names: Charlotte Pipe and Foundry Company®, Charlotte®, Charlotte Pipe®, and ChemDrain Corrosive Waste Drainage System. Þ Product is Certified to the International Plumbing Code. Installation in accordance with the manufacturer's instructions and the requirements of the latest edition of the International Plumbing Code.
Pipe# Þ	CPVC	ChemDrain®*	ASTM F2618
1 1/2"- 8"
# Charlotte Pipe ChemDrain Pipe and Fittings have been Certified as a system with the Charlotte Pipe ChemDrain One-Step CPVC Solvent Cement to ASTM F2618. * These pipe products are also represented by the trade names: Charlotte®, CPF®, and Charlotte Pipe®. Þ Product is Certified to the International Plumbing Code. Installation in accordance with the manufacturer's instructions and the requirements of the latest edition of the International Plumbing Code.
Pipe# Þ	CPVC	ChemDrain®*	CSA 181.3
1 1/2"- 8"
# Charlotte Pipe ChemDrain Pipe and Fittings have been Certified as a system with the Charlotte Pipe ChemDrain One-Step CPVC Solvent Cement to ASTM F2618. * These pipe products are also represented by the trade names: Charlotte®, CPF®, and Charlotte Pipe®. Þ Product is Certified to the International Plumbing Code. Installation in accordance with the manufacturer's instructions and the requirements of the latest edition of the International Plumbing Code.

¢ Product is authorized to bear the cNSF and/or the cNSFus Mark.

Drain, Waste, and Vent - Pipe and Fittings

Product Type	Material Type	Trade Name		Product Standard
Fittings	PVC	Charlotte	SE 28416
PVC 105-A - Fitting Cleanout Adapter w/O-ring Plug
1 1/2" - 6"
PVC 106-A Cleanout Plug w/ O-ring
1 1/2" - 6"
PVC 110-A - Flush Cleanout Plug w/ O-ring
2" - 4"
PVC 444-A - Cleanout Tee w/ O-ring Plug
1 1/2" - 6"
PVC 445-A - Cleanout Tee w/ Flush O-ring Plug
2" - 4"
PVC110-AB-Flush Cleanout Plug w/O-ring-Brass Ins
1 1/2" - 6"
PVC445-AB-Cleanout Tee w/Flush Oring Plug-Brss Ins
2" - 4"
Fittings	PVC	ConnecTite®		ASME A112.4.4
CTT 100 – Coupling
1 1/2", 2", 3"
CTT 300 – 90° Elbow 1/4 Bend
1 1/2", 2", 3"
CTT 321 – 45° Elbow 1/8 Bend
1 1/2", 2", 3"
CTT 400 – Sanitary Tee
1 1/2", 2", 3"
CTT 800s - Closet Flange
4" x 3"
Fittings	PVC	CPF®**		ASTM F1866
PVC 100 - Coupling (H x H)
14", 16"
PVC 101 - Female Adapter (H x FIPT)
10", 12"
PVC 101-X - Female Adapter with Raised Plug (H)
10", 12"
PVC 102 - Pipe Increaser - Reducer (H x H)
14" x 4"	14" x 6"	14" x 8"		14" x 10"
14" x 12"	16" x 4"	16" x 6"		16" x 8"
16" x 10"	16" x 12"	16" x 14"
PVC 105 - Fitting Cleanout Adapter (S x FIPT)
8", 10", 12"
PVC 105-X -Fitting Cleanout Adapter w/C.O. Plug(S)
8", 10", 12"
PVC 107 - Concentric Reducer Bushing (S x H)
14" x 4"	14" x 6"	14" x 8"		14" x 10"
14" x 12"	16" x 4"	16" x 6"		16" x 8"
16" x 10"	16" x 12"	16" x 14"
PVC 115-Adapter Coupling(SDR 35 HUBxDWV HUB)(HxH)
8", 10", 12"	10" x 8"
PVC 116 - Cap (H)
16", 14"
PVC 120–Adapter Bushing (DWV Spigot x SDR 35 Hub)
8", 10", 12"
PVC 130 - Repair Coupling (H x H)
8", 10", 12"
PVC 300 - 1/4 Bend (H x H)
14", 16"
PVC 301 - Vent 1/4 Bend, Street (H & S)
8", 10", 12"
PVC 302 - 1/4 Bend, Street (S x H)
10", 12", 14", 16"
PVC 321 - 1/8 Bend (H x H)
14", 16"
PVC 323 - 1/8 Bend, Street (H x S)
14", 16"
PVC 324 - 1/16 Bend (H x H)
14", 16"
PVC 326 - 1/16 Bend, Street (S x H)
8", 10", 12", 14", 16"
PVC 328 - 1/32 Bend (H x H)
8", 10", 12"
PVC 400 - 45° Tee (H x H x H)
10", 12"
PVC 400-A - Straight Tee (H x H x H)
14" x 14" x 14"	16" x 16" x 16"
PVC 401-A - Straight Tee, Reducing (H x H x H)
14" x 14" x 4"	14" x 14" x 6"	14" x 14" x 8"		14" x 14" x 10"
14" x 14" x 12"	16" x 16" x 4"	16" x 16" x 6"		16" x 16" x 8"
16" x 16" x 10"	16" x 16" x 12"	16" x 16" x 14"
PVC 410 - Tee Cross (H x H x H x H)
6" x 6" x 4" x 4"	6" x 6" x 6" x 6"	8" x 8" x 4" x 4"		8" x 8" x 6" x 6"
8" x 8" x 8" x 8"	10" x 10" x 4" x 4"	10" x 10" x 6" x 6"		10" x 10" x 8" x 8"
10 " x 10 " x 10 " x 10"	12" x 12" x 4" x 4"	12" x 12" x 6" x 6"		12" x 12" x 8" x 8"
12" x 12" x 10 " x 10"	12" x 12" x 12" x 12"
PVC 444-x–Cleanout Tee w/Cleanout Plug (HxHxFIPT)
8" x 8" x 4"	10"	10" x 10" x 4"		10" x 10" x 6"
12"	12" x 12" x 4"	12" x 12" x 10"
PVC 445 - Flush Cleanout Tee (H x H x FIPT)
8" x 8" x 4"	8" x 8" x 6"	10" x 10" x 4"		10" x 10" x 6"
10" x 10" x 10"	12" x 12" x 4"	12" x 12" x 6"		12" x 12" x 10"
12" x 12" x 12"
PVC 503 - Combination Wye and 1/8 Bend (H x H x H)
14" x 14" x 14"	16" x 16" x 16"
PVC 504 – Combo Wye & 1/8 Bend, Reducing (HxHxH)
14" x 14" x 4"	14" x 14" x 6"	14" x 14" x 8"		14" x 14" x 10"
14" x 14" x 12"	16" x 16" x 4"	16" x 16" x 6"		16" x 16" x 8"
16" x 16" x 10"	16" x 16" x 12"	16" x 16" x 14"
PVC 600 - Wye (H x H x H)
14", 16"
PVC 601 - Wye Reducing (H x H x H)
14" x 4"	14" x 6"	14" x 8"		14" x 10"
14" x 12"	16" x 4"	16" x 6"		16" x 8"
16" x 10"	16" x 12"	16" x 14"
PVC 611 - Double Wye (H x H x H x H)
8", 10", 12", 14"
PVC 612 - Double Wye, Reducing (H x H x H x H)
8" x 8" x 4" x 4"	8" x 8" x 6" x 6"	10" x 10" x 4" x 4"		10" x 10" x 6" x 6"
10" x 10" x 8" x 8"	12" x 12" x 4" x 4"	12" x 12" x 6" x 6"		12" x 12" x 8" x 8"
12" x 12" x 10" x 10"	14" x 14" x 4" x 4"	14" x 14" x 6" x 6"		14" x 14" x 8" x 8"
14" x 14" x 10" x 10"	14" x 14" x 12" x 12"	16" x 16" x 4" x 4"		16" x 16" x 6" x 6"
16" x 16" x 8" x 8"	16" x 16" x 10" x 10"	16" x 16" x 12" x 12"		16" x 16" x 14" x 14"
** These fitting products may also be represented by the trade names: Charlotte Pipe and Foundry Company®, Charlotte Plastics®, Charlotte Pipe®, Charlotte®, Charlotte or Char®.
Fittings@	ABS	CPF®**		*SE 7992*
ABS 130 - Repair Coupling (Hub x Hub)
1 1/2", 2", 3", 4", 6"
ABS 720X - Drum Trap w/Cleanout
3" x 6" x 1 1/2"
@ A letter after the part number designates the following: X - Metal Ring/Plastic Plug R - Reducing P - Plastic Ring W - Washer ** These fitting products may also be represented by the trade names: Charlotte Pipe and Foundry Company®, Charlotte Plastics®, Charlotte Pipe®, Charlotte®, Charlotte or Char®.
Fittings@ ¢	ABS	CPF®		CSA B181.1
ABS 100 - Coupling (Hub x Hub)
1 1/4", 1 1/2", 2", 3", 4", 6", 8", 10", 12"
ABS 101- Female Adapter (Hub x FTP)
1 1/2", 2", 3", 4", 6"
ABS 102 - Pipe Increaser - Reducer (Hub x Hub)
1 1/2" x 2", 1 1/2" x 3", 2" x 3", 2" x 4", 3" x 4"
ABS 103 - Trap Adapter-Male (SPG x SLIP)
1 1/2"	2"	1 1/2" x 1 1/4"
ABS 103P - Trap Adapter-Male w/Plastic Nut
1 1/2"	1 1/2" x 1 1/4"
ABS 103R - Trap Adapter-Male w/Plastic Nut
1 1/2"
ABS 103W – Trap Adapter Male w/Plas Nut-Washer
1 1/2"	1 1/2" x 1 1/4"	2"
ABS 103x - Trap Adapter-Male w/Chrome Nut
1 1/2"	1 1/2" x 1 1/4"
ABS 104 - Trap Adapter-Female (Hub x Slip)
1 1/2" x 1 1/4", 1 1/2", 2"
ABS 104P - Trap Adapter-Female w/Plastic Nut
1 1/2" x 1 1/4"	1 1/2"
ABS 104R – Trap Adapter Female w/Plast Washer-Nut
1 1/2"
ABS 104W –Trap Adapter Female w/Plastic Nut-Washer
1 1/2" x 1 1/4"	1 1/2"
ABS 104X – Trap Adapter Female w/Chrome Nut
1 1/2"	1 1/2" x 1 1/4"	2"
ABS 107 - Flush Bushing (SPG x Hub)
2" x 1 1/4"	4" x 3", 6" x 4"	3" x 2", 4" x 2"		3" x 1 1/2"
2" x 1 1/2"	1 1/2" x 1 1/4"
ABS 109–Male Adptr- not accept tail pc (MPT x Hub)
1 1/2", 2", 3", 4"
ABS 111- Male Fitting Adapter (SPG x MPT)
1 1/2"	2"
ABS 113 - Tray Plug Adapter (Hub)
1 1/2"
ABS 113S - Tray Plug Adapter (SPG)
1 1/2"
ABS 114 - Threaded Cap (FPT)
1 1/2"
ABS 116 - Cap (Socket)
1 1/2", 2", 3", 4", 6"
ABS 117 - Adapter Coupling (Hub x Hub)
4" x 3"	4" x 4"
ABS 118 - Adapter Bushing (DWV SPG x Hub)
3", 4"
ABS 119 - No-Hub Adapter (SPG x Hub)
1 1/2", 2", 3", 4, 4" x 3"
ABS 122 - Spigot Adapter, Cast iron (Hub x Hub)[4]
2" x 2", 4" x 4"
ABS 123 - Hub Adapter, Cast Iron (Hub x SPG)[1]
2" x 2"	4" x 4"
ABS 123R -Hub Adapter,Cast Iron,Increaser(HubxSPG)
1 1/2" x 2", 3" x 4"
ABS 130 - Repair Coupling (Hub x Hub)
1 1/2", 2", 3", 4", 6"
ABS 131 - Test Cap
1 1/2", 2", 3", 4"
ABS 300 - 90° Elbows 1/4 Bend (Hub x Hub)V
1 1/2", 2", 3", 4" 6"
ABS 300R - 90° Elbows 1/4 Bend, Reducing (HubxHub)
2" x 1 1/2"
ABS 300s–90° Elbow1/4Bend,with Side Inlet(All Hub)
3" x 3" x 2"
ABS 302 - 90° Elbows 1/4 Bend, Street (SPG x Hub)
1 1/2", 2", 3", 4"
ABS 303 - 90° Elbow 1/4 Bend w/Low Heel Inlet(Hub)
3 x 3 x 1 1/2", 3" x 3" x 2", 4" x 4" x 2"
ABS 303S - Elbow 1/4 Bend with Side Inlet
3" x 3" x 1 1/2"
ABS 304 - 90° Elbows Long Sweep 1/4 Bend (HubxHub)
1 1/2", 2", 3", 4"
ABS 305 - 90° Elbow Long Sweep ¼Bend w/ Inlet(Hub)
3" x 3" x 2"
ABS 307 - 90° Elbow Long Sweep ¼Bend w/Inlet(Hub)
3" x 3" x 1 1/2"	3" x 3" x 2"
ABS 309-90° Elbow Long Sweep ¼Bend,Street(HubxSPG)
1 1/2", 2", 3"
ABS 310–90° Elbow ¼ Bend LowHeelInlet HubxSPG xHub
3" x 3" x 2"
ABS 311–90° Elbow Long Swp ¼ Bend Side Inlet (Hub)
3" x 3" x 2"
ABS 319 - 60° Elbow 1/6 Bend (Hub x Hub)
1 1/2", 2", 3", 4"
ABS 320 - 60º Elbow 1/6 Bend, Street (SPG x Hub)
1 1/2", 2", 3"
ABS 321 - 45° Elbows 1/8 Bend (Hub x Hub)
1 1/2", 2", 3", 4", 6"
ABS 323 - 45º Elbows 1/8 Bend, Street (SPG x Hub)
1 1/2", 2", 3", 4", 6"
ABS 324 - 22 1/2° Elbow 1/16 Bend (Hub x Hub)
1 1/2", 2", 3", 4", 6"
ABS 326 - 22 1/2° Elbow 1/16 Bend Street (SPGxHub)
1 1/2", 2", 3", 4"
ABS 327 - 90° Elbows Double 1/4 bend (ALL HUB)
1 1 /2", 2", 3", 2" x 1 1/2" x 1 1/2"
ABS 328X - Closet Bend Short w/Test Cap
3" x 4"
ABS 329 - Closet Bend, Reducing (Hub x Hub)
3" x 4"
ABS 330 - Closet Bend, Reducing (Hub x SPG)
3" x 4"
ABS 330x-Closet Bend Reducing w/ Test Cap(HubxSPG)
3" x 4"
ABS 331 - Vent Ell (Hub x Hub)
1 1/2", 2", 3"
ABS 333 - Vent Ell, Street (Hub x SPG)
1 1/2", 2"
ABS 400 - Sanitary Tee (ALL HUB)
1 1/2", 2", 3", 4", 6"
ABS 401 - Sanitary Tee, Reducing (All Hub)
2" x1 1/2" x 1 1/2"	2" x 1 1/2" x 2"	2" x 2" x 1 1/2"		3" x 3" x 1 1/2"
3" x 3" x 2"	4" x 4 "x 2"	4" x 4" x 3"		6" x 6" x 4"
ABS 403 - Sanitary Tee, Street (SPG x Hub x Hub)
1 1/2", 2", 3", 4"
ABS 404 -Sanitary Tee,Street,Reducing(SPGxHubxHub)
2" x 1 1/2" x 1 1/2"	2" x 1 1/2" x 2"	2" x 2" x 1 1/2"		3" x 3" x 1 1/2"
3" x 3" x 2"
ABS 416 - Sanitary Tee with Left Side Inlet (Hub)
3" x 3" x 3" x 1 1/2"	3"x 3" x 3" x 2"
ABS 417 – Sanitary Tee w/Right Side Inlet(All Hub)
3" x 3" x 3" x 1 1/2"	3" x 3" x 3" x 2"
ABS 418 - Sanitary Tee w/R & L Side Inlet (Hub)
3" x 3" x 3" x 2" x 2"	4" x 4" x 4" x 2" x 2"
ABS 428 - Double Sanitary Tee (All Hub)
1 1/2", 2", 3", 4"
ABS 429 - Double Sanitary Tee, Reducing (All Hub)
2" x 2" x 1 1/2" x 1 1/2"	3" x 3" x 1 1/2" x 1 1/2"	3" x 3" x 2" x 2"		4" x 4" x 2" x 2"
4" x 4" x 3" x 3"
ABS 438 - Dbl Sanitary Tee w/Side Inlet (Hub)
3" x 3" x 3" x 3" x 2"	4" x 4" x 4" x 4" x 2"
ABS 439 - Dbl Sanitary Tee w/R&LSide Inlets (Hub)
3" x 3" x 3" x 3" x 2" x 2"	4" x 4" x 4" x 4" x 2" x 2"
ABS 441 - Vent Tee (All Hub)
1 1/2", 2", 3"
ABS 447 - Horizontal Twin Tee (All Hub)
3" x 3" x 1 1/2" x 1 1/2"
ABS 448 - Two-Way Cleanout (All Hub)
3", 4"
ABS 500 - Double Fixture Fitting (All Hub)
2", 3"	2" x 1 1/2" x 1 1/2" x 1 1/2"	2" x 1 1/2" x 2" x 2"		2" x 2" x 1 1/2" x 1 1/2"
3" x 2" x 3" x 3"
ABS 501 - Comb Wye and 1/8 Bend (All Hub)
1 1/2", 2", 3", 4"
ABS 502-Comb Wye & 1/8 Bend, Reducing One Pc.(Hub)
2" x 1 1/2" x 1 1/2"	2" x 1 1/2" x 2"	2" x 2" x 1 1/2"		3" x 3" x 1 1/2"
3" x 3" x 2"	4" x 4" x 2"	4" x 4" x 3"
ABS 600 - Wye (ALL HUB)
1 1/2", 2" 3",4",6"
ABS 601 - Wye, Reducing (All Hub)
2" x 1 1/2" x 1 1/2"	2" x 1 1/2" x 2"	2" x 2" x 1 1/2"		3" x 3" x 1 1/2"
3" x 3" x 2"	4" x 4" x 1 1/2"	4" x 4" x 2"		4" x 4" x 3"
6" x 6" x 4"
ABS 602 - Wye, Street (SPG x Hub x Hub)
1 1/2", 2", 3", 4"
ABS 603 - Wye, Street, Reducing (SPG x Hub x Hub)
3" x 3" x 1 1/2"	3" x 3" x 2"	4" x 4" x 3"
ABS 611 - Double Wye (All Hub)
1 1/2", 2", 3", 4"
ABS 612 - Double Wye, Reducing (All Hub)
2" x 2" x 1 1/2" x 1 1/2"	3" x 3" x 1 1/2" x 1 1/2"	3" x 3" x 2" x 2"		4" x 4" x 3" x 3"
ABS 700 - Return Bend (Hub x Hub)
1 1/2", 2", 3", 4"
ABS 704 - Tail Piece Adapter (SPG x Slip)
1 1/2"
ABS 704P-Tail Piece Adapter(SPGxSlip)w/Plastic Nut
1 1/2"
ABS 706x - P-Trap (Hub x Hub)
1 1/2", 2", 3", 4"
ABS 708P - P-Trap (Hub x Hub with Plastic Nut)
1 1/2", 2"
ABS 708x - P-Trap (Hub x Hub with Chrome Nut)
1 1/2"
ABS 710-DWV Low Profile P-Trap w/Solvent Weld Jnt
2"
ABS 711P - L.A. Pattern P-Trap (Slip x Hub)[3]
1 1/2"
ABS 711W-L.A. Pattern P-Trap Plstc Nut (SlipxHub)[3]
1 1/2"
ABS 900-Swivel Tray Plug Adapter w/Washer(SPGxFPT)
1 1/2"
ABS 900x - ABS Ext Swivel Tray Adp
1 1/2"
ABS 910-Swivel Tray Plug Adapter w/Washer(SPGxFPT)
1 1/2"
[4] This is an ABS to Cast Iron transition fitting. As such, only the ABS adapter side of the fitting meets the dimensional requirements of ASTM D2661 and CSA B181.1. [1] Plain End: Joint can be made with compression gasket only. [3] Furnished with 1 1/2 and 1 1/2 x 1 1/4 Polyethylene nut/washer combination. @ A letter after the part number designates the following: X - Metal Ring/Plastic Plug R - Reducing P - Plastic Ring W - Washer ¢ Product is authorized to bear the cNSF and/or the cNSFus Mark.
Fittings@	PVC	CPF®**		*SE 7992*
PVC 130 - Repair Coupling (Hub x Hub)
1 1/2", 2", 3", 4", 6"
@ A letter after the part number designates the following: X - Metal Ring/Plastic Plug R - Reducing P - Plastic Ring W - Washer ** These fitting products may also be represented by the trade names: Charlotte Pipe and Foundry Company®, Charlotte Plastics®, Charlotte Pipe®, Charlotte®, Charlotte or Char®.
Fittings@ §	PVC	CPF®**		ASTM D2665
PVC 100 - Coupling (Hub x Hub)
1 1/4", 1 1/2", 2", 3", 4", 6", 8", 10", 12"
PVC 101 - Female Adapter (FPT x Hub)
1 1/4", 1 1/2", 2", 3", 4", 6", 8"
PVC 102 - Pipe Increaser-Reducer (Hub x Hub)
1 1/2"x2", 1 1/2"x3", 2"x3", 2"x4", 3"x4", 3"x6", 4"x6",4"x8", 4"x10", 4"x12"	6"x8", 6'x10", 6"x12", 8"x10", 8"x12", 10"x12"
PVC 103 - Trap Adapter-Male
1 1/2"	1 1/2" x 1 1/4"	2"
PVC 104 - Trap Adapter-Female (Hub x SLIP)
1 1/2"	1 1/2" x 1 1/4"	1 1/4"		2"
PVC 105 - Fitting Cleanout Adapter (SPG x FPT)
1 1/4", 1 1/2", 2", 3", 4", 6", 8"
PVC 105-X - Fitting Cleanout Adapter w/C.O. Plug
1 1/2", 2", 3", 4", 6", 8"
PVC 106 - Cleanout Plug (MPT)
1 1/2", 2", 3", 4", 6", 8", 10", 12"
PVC 107 - Flush Bushing (SPG x HUB)
1 1/2"x1 1/4", 2"x1 1/4", 2"x1 1/2", 3"x1 1/2", 3"x2", 4"x2"	4"x3", 6"x4", 8"x4", 8"x6", 10"x4", 10"x6", 10"x8", 12"x4", 12"x6", 12"x8"	12"x10"
PVC 108 - Flush Bushing{Cleanout Adapter}(SPGxFPT)
2" x 1 1/2, 8" x 6", 10" x 8", 12" x 8"
PVC 108X - Flush Bushing w/Plug
2" x 1 1/2", 10" x 8", 12" x 8"
PVC 109 - Male Adapter (Not accept a tail piece)
1 1/4", 1 1/4" x 1 1/2", 1 1/2", 1 1/2" x 1 1/4", 2", 3", 4"
PVC 110 - Flush Cleanout Plug (MPT)
2", 3", 4"
PVC 110B - Flush Cleanout Plug - Brass Insert
2", 3", 4"
PVC 111 - Male Adapter (SPG x MPT)
1 1/2"	1 1/2" x 1 1/4"	2"		3"
PVC 113 - Tray Pl Adp H
1 1/2"
PVC 116 - Cap (SOCKET)
1 1/2", 2", 3", 4", 6", 8", 10", 12"
PVC 117x - Adapter Coupling S&D Spigot/DWV Hub
4" x 3"
PVC 117–Adapter Coupling/Adapts S&D SPG to DWV SPG
3"	4" x 3", 4" x 4"
PVC 118 - Adapter Bushing
3", 4"
PVC 119 - No Hub Adapter (Slip x Hub)
1 1/2", 2", 2" x 1 1/2", 3", 4", 4" x 3"
PVC 122 - Spigot Adapter, Cast Iron (Hub x Hub)
2" x 2", 3" x 3", 4" x 4"
PVC 123 - Hub Adapter, Cast Iron (Hub x SPG)
2" x 2", 3" x 3", 4" x 4"
PVC 123-R-Hub Adapter,Cast Iron,Increaser(HubxSPG)
1 1/2" x 2", 3" x 4"
PVC 131 - Test Cap
1 1/2", 2", 3", 4"
PVC 300 - 1/4 Bend (Hub x Hub)
1 1/4", 1 1/2", 2", 3", 4", 6", 8", 10", 12"
PVC 300-R - 1/4 Bend, Reducing (Hub x Hub)
2" x 1 1/2"
PVC 302 - 1/4 Bend, Street (SPG x Hub)
1 1/4", 1 1/2", 2", 3", 4", 6", 8"
PVC 303 -1/4 Bend with Low Heel Inlet(HubxHubxHub)
3" x 3" x 1 1/2", 3" x 3" x 2", 4" x 4" x 2"
PVC 304 - Long Sweep 1/4 Bend (Hub x Hub)
1 1/2", 2", 3", 4", 6"
PVC 305 - Long Sweep 1/4 Bend W/High Heel Inlet
3" x 3" x 2"
PVC 307 - Long Sweep 1/4 Bend w/Low Heel Inlet
3" x 3" x 1 1/2"	3" x 3" x 2"
PVC 309 - Long Sweep 1/4 Bend, Street (Hub x SPG)
1 1/2", 2", 3", 4"
PVC 310–¼ Bend Street Low Heel Inlet (HubxSPGxHub)
3" x 3" x 2"
PVC 319 - 1/6 Bend (Hub x Hub)
1 1/2", 2", 3", 4"
PVC 320 - 1/6 Bend Street (Hub x SPG)
1 1/2", 2", 3", 4"
PVC 321 - 1/8 Bend (Hub x Hub)
1 1/4", 1 1/2", 2", 3", 4", 6", 8", 10", 12"
PVC 323 - 1/8 Bend, Street (SPG x Hub)
1 1/4", 1 1/2", 2", 3", 4", 6", 8", 10", 12"
PVC 324 - 1/16 Bend (Hub x Hub)
1 1/2", 2", 3", 4", 6", 8", 10", 12"
PVC 326 - 1/16 Bend, Street (SPG x Hub)
1 1/2", 2", 3", 4", 6", 8"
PVC 327 - Double 1/4 Bend (Hub x Hub x Hub)
1 1/2", 2", 3", 2 x 1 1/2" x 1 1/2"
PVC 329 - Closet Bend, Reducing (Hub x Hub)
3" x 4"
PVC 330 - Closet Bend, Reducing (Hub x SPG)
3" x 4"
PVC 330-X-Closet Bend,Reducing w/Test Cap(HubxSPG)
3" x 4"
PVC 331 - Vent Ell (Hub x Hub)
1 1/2", 2", 3"
PVC 333 - Vent Ell, Street (Hub x SPG)
1 1/2", 2", 3"
PVC 400 - Sanitary Tee (All Hub)
1 1/4", 1 1/2", 2", 3", 4", 6", 8", 10", 12"
PVC 401 - Sanitary Tee, Reducing (All Hub)
2" x 1 1/2" x 1 1/2"	2" x 1 1/2" x 2"	2" x 2" x 1 1/2"		3" x 3" x 1 1/2"
3" x 3" x 2"	4" x 4" x 1 1/2"	4" x 4" x 2"		4" x 4" x 3"
6" x 6" x 4"	8" x 8" x 4"	8" x 8" x 6"		10" x 10" x 8"
12" x 12" x 8"	12" x 12" x 10"
PVC 403 - Sanitary Tee, Street (SPG x Hub x Hub)
1 1/2", 2", 3", 4"
PVC 404 -Sanitary Tee,Street,Reducing(SPGxHubxHub)
2"x2"x1 1/2", 3"x3"x1 1/2", 3"x3"x2", 4"x4"x2"
PVC 416 - Sanitary Tee w/Left Side Inlet (All Hub)
3" x 3" x 3" x 1 1/2"	3" x 3" x 3" x 2"	4" x 4" x 4" x 2"
PVC 417 - Sanitary Tee w/Right Side Inlet(All Hub)
3" x 3" x 3" x 1 1/2"	3" x 3" x 3" x 2"	4" x 4" x 4" x 2"
PVC 418–Sanitary Tee Right & Left Side Inlet (Hub)
3" x 3" x 3" x 2" x 2", 4" x 4" x 4" x 2" x 2"
PVC 428 - Double Sanitary Tee (All Hub)
1 1/2", 2", 3", 4"
PVC 429 - Double Sanitary Tee, Reducing (All Hub)
2" x 2" x 1 1/2"x1 1/2"	3" x 3"x 1 1/2"x1 1/2"	3" x 3" x 2" x 2"		4" x 4" x 1 1/2" x 1 1/2"
4" x 4" x 2" x 2"	4" x 4" x 3" x 3"
PVC 431–Dbl Sanitary Tee, St, Red. SPGxHubxHubxHub
3" x 3" x 1 1/2" x 1 1/2"
PVC 438 - Dbl Sanitary Tee w/ Side Inlet (All Hub)
3" x 3" x 3" x 3" x 2", 4" x 4" x 4" x 4" x 2"
PVC 439 - Dbl San Tee w/ Right & Left Side Inlets
3" x 3" x 3" x 3" x 2" x 2", 4" x 4" x 4" x 4" x 2" x 2"
PVC 441 - Vent Tee (All Hub)
1 1/2", 2", 3", 4", 6", 8"
PVC 444-X - Cleanout Tee w/ Cleanout Plug(HubxHub)
10" x 10" x 8", 12" x 12" x 6", 12" x 12" x 8"	1 1/2", 2", 3", 4", 6", 8", 6" x 6" x 4", 8" x 8" x 6"
PVC 445 - Flush Cleanout Tee (Hub x Hub x FPT)
1 1/2", 2", 3", 4", 6", 8", 10" x 10" x 8", 12" x 12" x 8"
PVC 445-X - Flush Tee w/ Cleanout Plug (Hub x Hub)
1 1/2", 2", 3", 4"
PVC 448 - Two-Way Cleanout (All Hub)
3", 4", 6"
PVC 449 - Sanitary Tee (All Hub)
2"
PVC 500 - Double Fixture Fitting (All Hub)
2", 3", 2" x 1 1/2" x 1 1/2" x 1 1/2", 2" x 2" x 1 1/2" x 1 1/2"
PVC 501 – Comb. Wye & 1/8 Bend-One Piece (All Hub)
1 1/2", 2", 3", 4"
PVC 502 - Comb Wye & 1/8 Bend, Reducer (All Hub)
2" x 1 1/2" x 1 1/2"	2" x 1 1/2" x 2"	2" x 2" x 1 1/2"		3" x 3" x 1 1/2"
3" x 3" x 2"	4" x 4" x 2"	4" x 4" x 3"
PVC 503 - Combination Wye and 1/8 Bend (H x H x H)
6" x 6" x 6"	8" x 8" x 8"	12" x 12" x 12"
PVC 504–Comb. Wye & 1/8 Bend Red., Two Piece (Hub)
4” x 4" x 3"	6" x 6" x 3"	6" x 6" x 4"		8" x 8" x 4"
8" x 8" x 6"	10" x 10" x 4"	10" x 10" x 6"		10" x 10" x 8"
12" x 12" x 4"	12" x 12" x 6"	12" x 12" x 8"		12" x 12" x 10"
PVC 507 - Dbl Combination Wye & 1/8 Bend (ALL HUB)
1 1/2", 2", 3", 4"	2" x 2" x 1 1/2" x 1 1/2"	3" x 3" x 2" x 2"		4" x 4" x 2" x 2"
4" x 4" x 3" x 3"	6" x 6" x 4" x 4"
PVC 515 - Comb Wye & 1/8 Bend w/ Left Side Inlet
3" x 3" x 3" x 2"
PVC 516–Comb. Wye & 1/8 Bend Rgt Side Inlet (Hub)
3" x 3" x 3" x 2"
PVC 517–Comb. Wye & 1/8 Bend Rgt & Lft Inlet (Hub)
3" x 3" x 3" x 2" x 2"
PVC 600 - Wye (All Hub)
1 1/4", 1 1/2", 2" 3",4",6", 8", 10", 12"
PVC 601 - Wye, Reducing (All Hub)
2" x 1 1/2" x 1 1/2"	2" x 1 1/2" x 2"	2" x 2" x 1 1/2"		3" x 3" x 1 1/2"
3" x 3" x 2"	4" x 4" x 1 1/2"	4" x 4" x 2"		4" x 4" x 3"
6" x 6" x 3"	6" x 6" x 4"	8" x 8" x 4"		8" x 8" x 6"
10" x 10" x 4"	10" x 10" x 6"	10" x 10" x 8"		12" x 12" x 4"
12" x 12" x 6"	12" x 12" x 8"	12" x 12" x 10"
PVC 602 - Wye, Street (SPG x Hub x Hub)
1 1/2", 2", 3", 4"
PVC 603 - Wye, Street, Reducing (SPG x Hub x Hub)
3" x 3" x 1 1/2"	3" x 3" x 2"	4" x 4" x 2"		4" x 4" x 3"
PVC 611 - Double Wye (ALL HUB)
1 1/2", 2", 3", 4", 6"
PVC 612 - Double Wye, Reducing (ALL HUB)
2" x 2" x 1 1/2" x 1 1/2"	3" x 3" x 1 1/2" x 1 1/2"	3" x 3" x 2" x 2"		4" x 4" x 2" x 2"
4" x 4" x 3" x 3"	6" x 6" x 4" x 4"
PVC 700 - Return Bend (Hub x Hub)
1 1/2", 2", 3", 4"
PVC 703P - Tray Adapter
1 1/2" x 1 1/4"
PVC 703X - Tray Adapter
1 1/2" x 1 1/4"
PVC 704P - Tail Piece Adpt.(SxSLIP w/ Plastic Nut)
1 1/2"
PVC 704X - Tail Piece Adpt. (SxSLIP w/ Chrome Nut)
1 1/2"
PVC 706-X - P-Trap (Hub x Hub)
1 1/2", 2", 3", 4"
PVC 707-X - P-Trap with Cleanout (Hub x Hub)
1 1/2", 2", 3", 4"
PVC 708-P - P-Trap (Hub x Hub with Plastic Nut)
1 1/4", 1 1/2", 2"
PVC 708-X - P-Trap (Hub x Hub with Chrome Nut)
1 1/2"
PVC 709-X - P-Trap w/Cleanout(HubxHubw/Chrome Nut)
1 1/2"
PVC 710 - Low Profile P-Trap w/Solvent Weld Joint
2"
PVC 711-X - L.A. Pattern P-Trap
1 1/2"
PVC 711P - L.A. Pattern P-Trap (Slip x Hub)
1 1/2"
PVC 800 - Closet Flange (Hub)
4" x 3", 4" x 4"
PVC 800KO - Closet Flange with Knock Out (Hub)
4" x 3", 4" x 4"
PVC 800s - Closet Flange with Stop (Hub)
4" x 3"
PVC 801 - Closet Flange, Reducing (SPIGOT)
4" x 3"
PVC 810-KO-Closet Flange,Adj w/PlasRing w-KnockOut
4" x 3"
PVC 811-KO-Closet Flange,Adj w/Metal/Plastic Ring
4" x 3"
PVC 811–Closet Flange, Adj Metal/Plastics Ring-Hub
4" x 3", 4" x 4"
PVC 812-Closet Flange, Adj w/ Metal/Plastic Ring
4" x 3", 4" x 4"
PVC 815-Flush Closet Flange-fits 3" or 4" (Hub)
4" x 4"/4" x 3"
PVC 815K-Flush Closet Flange w-Knock Out (Hub)
4" x 3"	4" x 4"
PVC 820-Offset Flange,Adj
4" x 3"
PVC 820P - Offset Flange, Adj Plastic Ring
4" x 3"
PVC 900 - Swivel Tray Plug Adp. w/ Washer(SpgxFPT)
1 1/2"
PVC 910 - Swivel Tray Plug Adp. w/ Washer (HxFPT)
1 1/2"
@ A letter after the part number designates the following: X - Metal Ring/Plastic Plug R - Reducing P - Plastic Ring W - Washer § Product is Certified to the Uniform Plumbing Code™. Installation in accordance with the manufacturer's instructions and the requirements of the latest edition of the Uniform Plumbing Code™. ** These fitting products may also be represented by the trade names: Charlotte Pipe and Foundry Company®, Charlotte Plastics®, Charlotte Pipe®, Charlotte®, Charlotte or Char®.
Fittings@	PVC	CPF®**		ASTM D2949
PVC 1100 - Coupling (Hub x Hub)
3 1/4"
PVC 1101 - Female Adapter (FPT x Hub)
3" x 3 1/4"
PVC 1102 - Pipe Increaser-Reducer (Hub x Hub)
1 1/2" x 3 1/4", 2" x 3 1/4", 3 1/4" x 4"
PVC 1105X - Fitting Cleanout Adpt w/ C.O. Plug
3" x 3 1/4"
PVC 1109 - Male Adapter (MPT x Hub)
3" x 3 1/4"
PVC 1112 - Reducer Bushing (SPG x Hub)
3 1/4" x 1 1/2", 3 1/4" x 2", 4" x 3 1/4"
PVC 1116 - Cap Socket
3"
PVC 1117 - Adapter Coupling (Hub x Hub)
4" x 3 1/4"
PVC 1129 - Hub Adapter (SPG x Hub)
3" x 3 1/4"
PVC 1130 - Repair Coupling
3"
PVC 1300 - 1/4 Bend (Hub x Hub)
3 1/4"
PVC 1302 - 1/4 Bend, Street (SPG x Hub)
3 1/4"
PVC 1303 - 1/4 Bend with Low Heel Inlet (All Hub)
3 1/4" x 3 1/4" x 2"
PVC 1319 - 1/16 Bend (Hub x Hub)
3 1/4"
PVC 1321 - 1/8 Bend (Hub x Hub)
3 1/4"
PVC 1323 - 1/8 Bend, Street (SPG x Hub)
3 1/4"
PVC 1324 - 1/16 Bend (Hub x Hub)
3 1/4"
PVC 1400 - Sanitary Tee (All Hub)
3 1/4"
PVC 1401 - Sanitary Tee, Reducing (All Hub)
3 1/4" x 3 1/4" x 1 1/2", 3 1/4" x 3 1/4" x 2"
PVC 1416 - Sanitary Tee w/ Left Side Inlet
3" x 3" x 3" x 2"
PVC 1418-Sanitary Tee w/Right and Left Side Inlet
3" x 3" x 3" x 1 1/2" x 1 1/2"	3" x 3" x 3" x 2" x 2"
PVC 1429 - Double Sanitary Tee, Reducing (All Hub)
3 1/4" x 3 1/4" x 1 1/2" x 1 1/2"
PVC 1444x - Tee with Cleanout Plug (Hub x Hub)
3 1/4"
PVC 1600 - Wye (All Hub)
3 1/4"
PVC 1601 - Wye, Reducing (All Hub)
3 1/4" x 3 1/4" x 1 1/2", 3 1/4" x 3 1/4" x 2"
PVC 1611 - Double Wye (All Hub)
3 1/4"
PVC 1800 - Closet Flange (Hub)
4" x 3 1/4"
PVC 1800KO - Closet Flange (Hub)
4" x 3 1/4"
PVC 1811 - Closet Flange, Adj {w/ Metal Ring}(Hub)
4" x 3 1/4"
PVC 1812 - Closet Flange (SPG)
4" x 3 1/4"
@ A letter after the part number designates the following: X - Metal Ring/Plastic Plug R - Reducing P - Plastic Ring W - Washer ** These fitting products may also be represented by the trade names: Charlotte Pipe and Foundry Company®, Charlotte Plastics®, Charlotte Pipe®, Charlotte®, Charlotte or Char®.
Fittings@ §	ABS	CPF®**		ASTM D2661
ABS 100 - Coupling (Hub x Hub)
1 1/4", 1 1/2", 2", 3", 4", 6", 8", 10", 12"
ABS 101- Female Adapter (Hub x FTP)
1 1/2", 2", 3", 4", 6"
ABS 102 - Pipe Increaser - Reducer (Hub x Hub)
1 1/2" x 2", 1 1/2" x 3", 2" x 3", 2" x 4", 3" x 4"
ABS 103 - Trap Adapter-Male (SPG x SLIP)
1 1/2"	2"	1 1/2" x 1 1/4"
ABS 103P - Trap Adapter-Male w/Plastic Nut
1 1/2"	1 1/2" x 1 1/4"
ABS 103R - Trap Adapter-Male w/Plastic Nut
1 1/2"
ABS 103W – Trap Adapter Male w/Plas Nut-Washer
1 1/2"	1 1/2" x 1 1/4"	2"
ABS 103x - Trap Adapter-Male w/Chrome Nut
1 1/2"	1 1/2" x 1 1/4"
ABS 104 - Trap Adapter-Female (Hub x Slip)
1 1/2" x 1 1/4", 1 1/2", 2"
ABS 104P - Trap Adapter-Female w/Plastic Nut
1 1/2" x 1 1/4"	1 1/2"
ABS 104R – Trap Adapter Female w/Plast Washer-Nut
1 1/2"
ABS 104W –Trap Adapter Female w/Plastic Nut-Washer
1 1/2" x 1 1/4"	1 1/2"
ABS 104X – Trap Adapter Female w/Chrome Nut
1 1/2"	1 1/2" x 1 1/4"	2"
ABS 105 - Fitting Cleanout Adapter (SPG x FPT)
1 1/4", 1 1/2", 2", 3", 4"
ABS 105x - Fitting Cleanout Adapter w/C.O. Plug
1 1/2", 2", 3", 4"
ABS 106 - Cleanout Plug (MPT)
1 1/2", 2", 2 1/2", 3", 3 1/2", 4", 6", 8"
ABS 107 - Flush Bushing (SPG x Hub)
1 1/2" x 1 1/4"	2" x 1 1/4"	2" x 1 1/2"		3" x 1 1/2"
3" x 2", 4" x 2"	4" x 3", 6" x 4"
ABS 108 - Flush Bushing(Cleanout Adapter)(HubxFPT)
2" x 1 1/2"	6" x 4"	6" x 8"
ABS 109–Male Adptr- not accept tail pc (MPT x Hub)
1 1/2", 2", 3", 4"
ABS 110 - Flush C.O. Plug (MPT)
2", 3", 4"
ABS 111- Male Fitting Adapter (SPG x MPT)
1 1/2"	2"
ABS 113 - Tray Plug Adapter (Hub)
1 1/2"
ABS 113S - Tray Plug Adapter (SPG)
1 1/2"
ABS 114 - Threaded Cap (FPT)
1 1/2"
ABS 116 - Cap (Socket)
1 1/2", 2", 3", 4", 6"
ABS 117 - Adapter Coupling (Hub x Hub)
4" x 3"	4" x 4"
ABS 118 - Adapter Bushing (DWV SPG x Hub)
3", 4"
ABS 119 - No-Hub Adapter (SPG x Hub)
1 1/2", 2", 3", 4, 4" x 3"
ABS 122 - Spigot Adapter, Cast iron (Hub x Hub)[4]
2" x 2", 4" x 4"
ABS 123 - Hub Adapter, Cast Iron (Hub x SPG)[1]
4" x 4"	2" x 2"
ABS 123R -Hub Adapter,Cast Iron,Increaser(HubxSPG)
1 1/2" x 2", 3" x 4"
ABS 131 - Test Cap
1 1/2", 2", 3", 4"
ABS 300 - 90° Elbows 1/4 Bend (Hub x Hub)
1 1/2", 2", 3", 4" 6"
ABS 300R - 90° Elbows 1/4 Bend, Reducing (HubxHub)
2" x 1 1/2"
ABS 300s–90° Elbow1/4Bend,with Side Inlet(All Hub)
3" x 3" x 2"
ABS 302 - 90° Elbows 1/4 Bend, Street (SPG x Hub)
1 1/2", 2", 3", 4"
ABS 303 - 90° Elbow 1/4 Bend w/Low Heel Inlet(Hub)
3 x 3 x 1 1/2", 3" x 3" x 2", 4" x 4" x 2"
ABS 303S - Elbow 1/4 Bend with Side Inlet
3" x 3" x 1 1/2"
ABS 304 - 90° Elbows Long Sweep 1/4 Bend (HubxHub)
1 1/2", 2", 3", 4"
ABS 305 - 90° Elbow Long Sweep ¼Bend w/ Inlet(Hub)
3" x 3" x 2"
ABS 307 - 90° Elbow Long Sweep ¼Bend w/Inlet(Hub)
3" x 3" x 1 1/2"	3" x 3" x 2"
ABS 309-90° Elbow Long Sweep ¼Bend,Street(HubxSPG)
1 1/2", 2", 3"
ABS 310–90° Elbow ¼ Bend LowHeelInlet HubxSPG xHub
3" x 3" x 2"
ABS 311–90° Elbow Long Swp ¼ Bend Side Inlet (Hub)
3" x 3" x 2"
ABS 319 - 60° Elbow 1/6 Bend (Hub x Hub)
1 1/2", 2", 3", 4"
ABS 320 - 60º Elbow 1/6 Bend, Street (SPG x Hub)
1 1/2", 2", 3"
ABS 321 - 45° Elbows 1/8 Bend (Hub x Hub)
1 1/2", 2", 3", 4", 6"
ABS 323 - 45º Elbows 1/8 Bend, Street (SPG x Hub)
1 1/2", 2", 3", 4", 6"
ABS 324 - 22 1/2° Elbow 1/16 Bend (Hub x Hub)
1 1/2", 2", 3", 4", 6"
ABS 326 - 22 1/2° Elbow 1/16 Bend Street (SPGxHub)
1 1/2", 2", 3", 4"
ABS 327 - 90° Elbows Double 1/4 bend (ALL HUB)
1 1 /2", 2", 3", 2" x 1 1/2" x 1 1/2"
ABS 328X - Closet Bend Short w/Test Cap
3" x 4"
ABS 329 - Closet Bend, Reducing (Hub x Hub)
3" x 4"
ABS 330 - Closet Bend, Reducing (Hub x SPG)
3" x 4"
ABS 330x-Closet Bend Reducing w/ Test Cap(HubxSPG)
3" x 4"
ABS 331 - Vent Ell (Hub x Hub)
1 1/2", 2", 3"
ABS 333 - Vent Ell, Street (Hub x SPG)
1 1/2", 2"
ABS 400 - Sanitary Tee (ALL HUB)
1 1/2", 2", 3", 4", 6"
ABS 401 - Sanitary Tee, Reducing (All Hub)
2" x 1 1/2" x 1 1/2"	2" x 1 1/2" x 2"	2" x 2" x 1 1/2"		3" x 3" x 1 1/2"
3" x 3" x 2"	4" x 4 "x 2"	4" x 4" x 3"		6" x 6" x 4"
ABS 403 - Sanitary Tee, Street (SPG x Hub x Hub)
1 1/2", 2", 3", 4"
ABS 404 -Sanitary Tee,Street,Reducing(SPGxHubxHub)
2" x 1 1/2" x 1 1/2"	2" x 1 1/2" x 2"	2" x 2" x 1 1/2"		3" x 3" x 1 1/2"
3" x 3" x 2"
ABS 416 - Sanitary Tee with Left Side Inlet (Hub)
3" x 3" x 3" x 1 1/2"	3"x 3" x 3" x 2"
ABS 417 – Sanitary Tee w/Right Side Inlet(All Hub)
3" x 3" x 3" x 1 1/2"	3" x 3" x 3" x 2"
ABS 418 - Sanitary Tee w/R & L Side Inlet (Hub)
3" x 3" x 3" x 2" x 2"	4" x 4" x 4" x 2" x 2"
ABS 428 - Double Sanitary Tee (All Hub)
1 1/2", 2", 3", 4"
ABS 429 - Double Sanitary Tee, Reducing (All Hub)
2" x 2" x 1 1/2" x 1 1/2"	3" x 3" x 1 1/2" x 1 1/2"	3" x 3" x 2" x 2"		4" x 4" x 2" x 2"
4" x 4" x 3" x 3"
ABS 438 - Dbl Sanitary Tee w/Side Inlet (Hub)
3" x 3" x 3" x 3" x 2"	4" x 4" x 4" x 4" x 2"
ABS 439 - Dbl Sanitary Tee w/R&LSide Inlets (Hub)
3" x 3" x 3" x 3" x 2" x 2"	4" x 4" x 4" x 4" x 2" x 2"
ABS 441 - Vent Tee (All Hub)
1 1/2", 2", 3"
ABS 444x - Cleanout Tee w/ Cleanout Plug (HubxHub)
1 1/2", 2", 3", 4", 6"
ABS 445 - Flush Cleanout Tee (Hub x Hub x FPT)
1 1/2", 2", 3", 4", 6"
ABS 447 - Horizontal Twin Tee (All Hub)
3" x 3" x 1 1/2" x 1 1/2"
ABS 448 - Two-Way Cleanout (All Hub)
3", 4"
ABS 500 - Double Fixture Fitting (All Hub)
2", 3"	2" x 1 1/2" x 1 1/2" x 1 1/2"	2" x 1 1/2" x 2" x 2"		2" x 2" x 1 1/2" x 1 1/2"
3" x 2" x 3" x 3"
ABS 501 - Comb Wye and 1/8 Bend (All Hub)
1 1/2", 2", 3", 4"
ABS 502-Comb Wye & 1/8 Bend, Reducing One Pc.(Hub)
2" x 1 1/2" x 1 1/2"	2" x 1 1/2" x 2"	2" x 2" x 1 1/2"		3" x 3" x 1 1/2"
3" x 3" x 2"	4" x 4" x 2"	4" x 4" x 3"
ABS 600 - Wye (ALL HUB)
1 1/2", 2" 3",4",6"
ABS 601 - Wye, Reducing (All Hub)
2" x 1 1/2" x 1 1/2"	2" x 1 1/2" x 2"	2" x 2" x 1 1/2"		3" x 3" x 1 1/2"
3" x 3" x 2"	4" x 4" x 1 1/2"	4" x 4" x 2"		4" x 4" x 3"
6" x 6" x 4"
ABS 602 - Wye, Street (SPG x Hub x Hub)
1 1/2", 2", 3", 4"
ABS 603 - Wye, Street, Reducing (SPG x Hub x Hub)
3" x 3" x 1 1/2"	3" x 3" x 2"	4" x 4" x 3"
ABS 611 - Double Wye (All Hub)
1 1/2", 2, 3, 4"
ABS 612 - Double Wye, Reducing (All Hub)
2" x 2" x 1 1/2" x 1 1/2"	3" x 3" x 1 1/2" x 1 1/2"	3" x 3" x 2" x 2"		4" x 4" x 3" x 3"
ABS 700 - Return Bend (Hub x Hub)
1 1/2", 2", 3", 4"
ABS 704 - Tail Piece Adapter (SPG x Slip)
1 1/2"
ABS 704P-Tail Piece Adapter(SPGxSlip)w/Plastic Nut
1 1/2"
ABS 706x - P-Trap (Hub x Hub)
1 1/2", 2", 3", 4"
ABS 707x - P-Trap with Cleanout (Hub x Hub)
1 1/2", 2"
ABS 708P - P-Trap (Hub x Hub with Plastic Nut)
1 1/2", 2"
ABS 708x - P-Trap (Hub x Hub with Chrome Nut)
1 1/2"
ABS 710-DWV Low Profile P-Trap w/Solvent Weld Jnt
2"
ABS 711P - L.A. Pattern P-Trap (Slip x Hub)[3]
1 1/2"
ABS 711W-L.A. Pattern P-Trap Plstc Nut (SlipxHub)[3]
1 1/2"
ABS 720X-Drum Trap with Cleanout
3" x 6" x 1 1/2"
ABS 800 - Closet Flange (Hub)
4" x 3", 4" x 4"
ABS 800Ko - Closet Flange with Knock Out (Hub)
4" x 3"
ABS 800S - Closet Flange with Stop (Hub)
4" x 3"
ABS 801 - Closet Flange, Reducing (SPG)
4" x 3"
ABS 808 - Closet Flange, Male (MPT)
4" x 3"
ABS 811-KO-Closet Flange, Adj w/Meta/Plasticl Ring
4" x 3"
ABS 811P - Closet Flange, Adj w/ABS Ring
4" x 3", 4" x 4"
ABS 811–Closet Flange, Adj Metal/Plstc Ring (Hub)
4" x 3", 4" x 4"
ABS 812-Closet Flange, Adj
4"x3", 4"x4"
ABS 812P - Closet Flange, Adj Plastic Ring
4" x 3"
ABS 815 - Flush Closet Flange
4"x4"/4"x3"
ABS 815Ko - Flush Closet Flange with Knockout[2]
4"x4"/4"x3"
ABS 820-Offset Flange, Adj
4"x3"
ABS 820P - Offset Flange, Adj Plastic Ring
4" x 3"
ABS 824-Closet Flange, Adjust. w/Metal Ring
4"
ABS 900-Swivel Tray Plug Adapter w/Washer(SPGxFPT)
1 1/2"
ABS 900x - ABS Ext Swivel Tray Adp
1 1/2"
ABS 910-Swivel Tray Plug Adapter w/Washer(SPGxFPT)
1 1/2"
[4] This is an ABS to Cast Iron transition fitting. As such, only the ABS adapter side of the fitting meets the dimensional requirements of ASTM D2661 and CSA B181.1. [1] Plain End: Joint can be made with compression gasket only. [3] Furnished with 1 1/2 and 1 1/2 x 1 1/4 Polyethylene nut/washer combination. [2] Fits Over 3" Pipe or Inside 4" Pipe. @ A letter after the part number designates the following: X - Metal Ring/Plastic Plug R - Reducing P - Plastic Ring W - Washer § Product is Certified to the Uniform Plumbing Code™. Installation in accordance with the manufacturer's instructions and the requirements of the latest edition of the Uniform Plumbing Code™. ** These fitting products may also be represented by the trade names: Charlotte Pipe and Foundry Company®, Charlotte Plastics®, Charlotte Pipe®, Charlotte®, Charlotte or Char®.
Pipe §*	PVC	Charlotte Pipe®***		ASTM D2665
1 1/4"- 16" Sch 40
* Sockets and gasketed bell ends are not tested or Listed by NSF for this production facility. § Product is Certified to the Uniform Plumbing Code™. Installation in accordance with the manufacturer's instructions and the requirements of the latest edition of the Uniform Plumbing Code™. *** These products may include the production location code PLNC in the trade name.
Pipe§	PVC	Charlotte Pipe®***		ASTM F891
1 1/2" - 12" Sch 40
§ Product is Certified to the Uniform Plumbing Code™. Installation in accordance with the manufacturer's instructions and the requirements of the latest edition of the Uniform Plumbing Code™. *** These products may include the production location code PLNC in the trade name.

Potable Water - Pipe and Fittings

Product Type	Material Type	Trade Name	Product Standard
Pipe§ +++ [G]	CPVC 4120	Charlotte Pipe Corzan®**	ASTM F441
1/4" - 12" Sch 40
1/4" - 12" Sch 80
§ Product is Certified to the Uniform Plumbing Code™. Installation in accordance with the manufacturer's instructions and the requirements of the latest edition of the Uniform Plumbing Code™. ** These pipe products may also be represented by the trade name: Charlotte Pipe CPVP 4120. +++ Material complies with NSF/ANSI/CAN 61 health effects requirements when tested at temperatures up to and including Commercial Hot (180° F). [G] Product is Certified to NSF/ANSI/CAN 372 and conforms with the lead content requirements for "lead free" plumbing as defined by California, Vermont, Maryland, and Louisiana state laws and the U.S. Safe Drinking Water Act.
Pipe + [G]*	PVC	Charlotte Pipe®***	CSA B137.3
1/8" - 18" Sch 40
1/8" - 18" Sch 80
3/4" - 18" SDR 21
1" - 18" SDR 26
2 1/2" - 12" SDR 32.5
4" - 12" SDR 41
* Sockets and gasketed bell ends are not tested or Listed by NSF for this production facility. + Material complies with NSF/ANSI/CAN 61 health effects requirements when tested at 73° F. *** These pipe products may include the production location code PLNC in the trade name. [G] Product is Certified to NSF/ANSI/CAN 372 and conforms with the lead content requirements for "lead free" plumbing as defined by California, Vermont, Maryland, and Louisiana state laws and the U.S. Safe Drinking Water Act.
Pipe + § [G]*	PVC	Charlotte Pipe®***	ASTM D1785
1/8" - 18" Sch 40
1/8" - 18" Sch 80
* Sockets and gasketed bell ends are not tested or Listed by NSF for this production facility. + Material complies with NSF/ANSI/CAN 61 health effects requirements when tested at 73° F. § Product is Certified to the Uniform Plumbing Code™. Installation in accordance with the manufacturer's instructions and the requirements of the latest edition of the Uniform Plumbing Code™. *** These pipe products may include the production location code PLNC in the trade name. [G] Product is Certified to NSF/ANSI/CAN 372 and conforms with the lead content requirements for "lead free" plumbing as defined by California, Vermont, Maryland, and Louisiana state laws and the U.S. Safe Drinking Water Act.
Pipe + § [G]*	PVC	Charlotte Pipe®***	ASTM D2241
1/2" SDR 13.5
3/4" - 18" SDR 21
1" - 18" SDR 26
2 1/2" - 12" SDR 32.5
4" - 12" SDR 41
* Sockets and gasketed bell ends are not tested or Listed by NSF for this production facility. + Material complies with NSF/ANSI/CAN 61 health effects requirements when tested at 73° F. § Product is Certified to the Uniform Plumbing Code™. Installation in accordance with the manufacturer's instructions and the requirements of the latest edition of the Uniform Plumbing Code™. *** These pipe products may include the production location code PLNC in the trade name. [G] Product is Certified to NSF/ANSI/CAN 372 and conforms with the lead content requirements for "lead free" plumbing as defined by California, Vermont, Maryland, and Louisiana state laws and the U.S. Safe Drinking Water Act.
Pipe§ +++ [G]	CPVC 4120	Charlotte Pipe®****	ASTM D2846
1/2" - 2" SDR 11
§ Product is Certified to the Uniform Plumbing Code™. Installation in accordance with the manufacturer's instructions and the requirements of the latest edition of the Uniform Plumbing Code™. +++ Material complies with NSF/ANSI/CAN 61 health effects requirements when tested at temperatures up to and including Commercial Hot (180° F). [G] Product is Certified to NSF/ANSI/CAN 372 and conforms with the lead content requirements for "lead free" plumbing as defined by California, Vermont, Maryland, and Louisiana state laws and the U.S. Safe Drinking Water Act. **** These pipe products may also be represented by the trade names: Charlotte Pipe® CPVC CTS™ or Charlotte Pipe® Flowguard Gold.
Fittings+ [G]	PVC	CPF®******	ASTM D2466
PVC 2100 Coupling (Hub x Hub)(429-xxx)
1/2"	3/4"	1"	1 1/4"
1 1/2"	2"	2 1/2"	3"
4"	6"	8"	10"
12"	3/4" x 1/2"	1" x 3/4"
PVC 2100D (Deep Socket) Coupling HubxHub (479-XXX)
1/2"	3/4"	1"	1 1/4"
1 1/2"	2"
PVC 2100N (Nesting) Coupling (477-XXX)
3/4"	1"
PVC 2101 Female Adapter (Hub x FPT)(435-xxx)
1/2"	3/4"	1"	1 1/4"
1 1/2"	2"	2 1/2"	3"
4"
PVC 2101 Female Adapter Reducing(HubxFPT)(435-xxx)
3/4" x 1/2"	3/4" x 1"	1" x 3/4"
PVC 2101S Female Adp Red (FPT x RS)
3/4" x 1/2"
PVC 2102 Coupling (FPT x FPT)(430-xxx)
1/2"	3/4"	1"
PVC 2103 Riser Extension (MPT x FPT)(439-xxx)
1/2" x 1/2"	3/4" x 3/4"
PVC 2104 Female Adaptor (Hub x FPT)
1/2" x 3/4"	3/4" x 1/2"
PVC 2107 Reducing Bushing (SPG x S)(437-xxx)
3/4" x 1/2"	1" x 1/2"	1" x 3/4"	1 1/4" x 1/2"
1 1/4" x 3/4"	1 1/4" x 1"	1 1/2" x 1/2"	1 1/2" x 3/4"
1 1/2" x 1"	1 1/2" x 1 1/4"	2" x 1/2"	2" x 3/4"
2" x 1"	2" x 1 1/4"	2" x 1 1/2"	2 1/2" x 2"
3" x 1 1/2"	3" x 2"	3" x 2 1/2"	4" x 2"
4" x 3"	6" x 4"	8" x 4"	8" x 6"
PVC 2108 Reducing Bushing (SPG x FPT)(438-xxx)
3/4" x 1/2"	1" x 1/2"	1" x 3/4"	1 1/4" x 1/2"
1 1/4" x 3/4"	1 1/4" x 1"	1 1/2" x 1/2"	1 1/2" x 3/4"
1 1/2" x 1"	1 1/2" x 1 1/4"	2" x 1/2"	2" x 3/4"
2" x 1"	2" x 1 1/4"	2" x 1 1/2"	3" x 2"
3" x 2 1/2"	4" x 2"	4" x 3"	6" x 4"
PVC 2109 Male Adapter (MPT x S)(436-xxx)
1/2"	3/4"	1"	1 1/4"
1 1/2"	2"	2 1/2"	3"
4"	6"
PVC 2110 Male Adapter Reducing(MPT x Hub)(436-xxx)
1/2" x 3/4"	3/4" x 1/2"	3/4" x 1"	1" x 3/4"
1" x 1 1/4"	1 1/4" x 1"	1 1/4" x 1 1/2"	1 1/2" x 1 1/4"
1 1/2" x 2"	2" x 1 1/2"
PVC 2112 Reducing Bushing (MPT x FPT)(439-xxx)
3/4" x 1/2"	1 x 1/2"	1" x 3/4"	1 1/4" x 1/2"
1 1/4" x 3/4"	1 1/4" x 1"	1 1/2" x 1/2"	1 1/2" x 3/4"
1 1/2" x 1"	1 1/2" x 1 1/4"	2" x 1"	2" x 1 1/4"
2" x 1 1/2"
PVC 2113 Plug (MPT)(450-xxx)
1/2"	3/4"	1"	1 1/4"
1 1/2"	2"
PVC 2116 Cap (Hub)(447-xxx)
1/2"	3/4"	1"	1 1/4"
1 1/2"	2"	2 1/2"	3"
4"	6"	8"
PVC 2117 Cap (FPT)(448-xxx)
1/2"	3/4"	1"	1 1/4"
1 1/2"	2"
PVC 2118 Plug (SPG)(449-xxx)
1/2"	3/4"	1"	1 1/4"
1 1/2"	2"
PVC 2300 90° Elbow (Hub x Hub)(406-xxx)
1/2"	3/4"	1"	1 1/4"
1 1/2"	2"	2 1/2"	3"
4"	6"	8"
PVC 2300 90° Reducing Elbow (Hub x Hub)(406-xxx)
3/4" x 1/2"	1" x 1/2"	1" x 3/4"	1 1/4" x 1"
1 1/2" x 1"
PVC 2301 90° Elbow (Hub x FPT)(407-xxx)
1/2"	3/4"	1"	1 1/4"
1 1/2"	2"
PVC 2301 90° Reducing Elbow (Hub x FPT)(407-xxx)
3/4" x 1/2"	1/2" x 3/4"	1" x 1/2"	1" x 3/4"
PVC 2302 90° Elbow (FPT x FPT)(408-xxx)
1/2"	3/4"	1"	1 1/4"
1 1/2"	2"
PVC 2304 90° Elbow (SPG x Hub)(409-xxx)
1/2"	3/4"	1"	1 1/4"
1 1/2"	2"
PVC 2306 90° Elbow (MPT x Hub)(410-xxx)
1/2"	3/4"	3/4" x 1/2"	1"
1 1/4"	1 1/2"	2"
PVC 2307 90° Elbow (MPT x FPT)(412-xxx)
1/2"	3/4"	1"	1 1/4"
1 1/2"	2"
PVC 2309 45° Elbow (Hub x Hub)(417-xxx)
1/2"	3/4"	1"	1 1/4"
1 1/2"	2"	2 1/2"	3"
4"	6"	8"
PVC 2310 Elbow (Socket x SPG)
2"
PVC 2400 Reducing Tee (All Hub)(401-xxx)
1/2" x 1/2" x 3/4"	3/4’‘ x 1/2’'x 1/2’‘	3/4" x 3/4" x 1/2"	3/4" x 1/2" x 3/4"
3/4" x 3/4" x 1"	1" x 3/4" x 1/2"	1" x 3/4" x 3/4"	1" x 3/4" x 1"
1" x 1" x 1/2"	1" x 1" x 3/4"	1" x 1" x 1 1/4"	1" x 1" x 1 1/2"
1 1/4" x 1" x 1/2"	1 1/4" x 1" x 3/4"	1 1/4" x 1" x 1"	1 1/4" x 1 1/4" x 1/2"
1 1/4" x 1 1/4" x 3/4"	1 1/4" x 1 1/4" x 1"	1 1/2" x 1 1/4" x 1/2"	1 1/2" x 1 1/2" x 1/2"
1 1/2" x 1 1/2" x 3/4"	1 1/2" x 1 1/2" x 1"	1 1/2" x 1 1/2" x 1 1/4"	1 1/2" x 1 1/2" x 2"
2" x 1 1/2" x 1 1/2"	2" x 2" x 3/4"	2" x 2" x 1/2"	2" x 2" x 1"
2" x 2" x 1 1/4"	2" x 2" x 1 1/2"	2 1/2" x 2 1/2" x 3/4"	2 1/2" x 2 1/2" x 1"
2 1/2" x 2 1/2" x 2"	2 1/2" x 2 1/2" x 1 1/4"	2 1/2" x 2 1/2" x 1 1/2"	3" x 3" x 1/2"
3" x 3" x 3/4"	3" x 3" x 1 1/4"	3" x 3" x 1 1/2"	3" x 3" x 1"
3" x 3" x 2"	4" x 4" x 3/4"	4" x 4" x 1 1/4"	4" x 4" x 1 1/2"
4" x 4" x 1"	4" x 4" x 2"	4" x 4" x 3"	6" x 6" x 4"
PVC 2400 Tee (All Hub)(401-xxx)
1/2"	3/4"	1"	1 1/4"
1 1/2"	2"	2 1/2"	3"
4"	6"	8"
PVC 2401 Reducing Tee (Hub x Hub x FPT)(402-xxx)
3/4" x 3/4" x 1/2"	1" x 1" x 1/2"	1" x 1" x 3/4"	1 1/4" x 1 1/4" x 1/2"
1 1/4" x 1 1/4" x 3/4"	1 1/4" x 1 1/4" x 1"	1 1/2" x 1 1/2" x 1/2"	1 1/2" x 1 1/2" x 3/4"
1 1/2" x 1 1/2" x 1"	2" x 2" x 1/2"	2" x 2" x 3/4"	2" x 2" x 1"
2" x 2" x 1 1/2"	2 1/2" x 2 1/2" x 3/4"	2 1/2" x 2 1/2" x 1 1/2"
PVC 2401 Tee (Hub xHub xFPT)(402-xxx)
1/2"	3/4"	1"	1 1/4"
1 1/2"	2"
PVC 2402 Tee (FPT x FPT x FPT) (405-XXX)
3/4"	1/2"	1"	1 1/2"
PVC 2410 Cross (All Hub)(420-xxx)
1/2"	3/4"	1"	1 1/4"
1 1/2"	2"
PVC 2510 – Side Outlet Elbow (All Hub)
1/2" x 1/2" x 1/2"	3/4" x 3/4" x 3/4"	1" x 1" x 1"	1 1/4" x 1 1/4" x 1 1/4"
1 1/2" x 1 1/2" x 1 1/2"	2"
PVC 2520 90° Elbow-S/OUT(Hub x Hub x FPT)(414-xxx)
1/2"	3/4" x 3/4" x 1/2"	1" x 1" x 1/2"
+ Material complies with NSF/ANSI/CAN 61 health effects requirements when tested at 73° F. [G] Product is Certified to NSF/ANSI/CAN 372 and conforms with the lead content requirements for "lead free" plumbing as defined by California, Vermont, Maryland, and Louisiana state laws and the U.S. Safe Drinking Water Act. ****** These fitting products may also be represented by the trade names: Charlotte, Charlotte Pipe and Foundry Company®, Charlotte Pipe®, Charlotte Plastics®, Charlotte®, and Char®.
Fittings+ [G]	PVC	CPF®******	ASTM D2467
PVC 8400 Tee (All Hub)(801-xxx)
1/2"	3/4"	1"	1 1/4"
1 1/2"	2"	2 1/2"	3"
4"	6"	8"	10"
12"
PVC 8400 Reducing Tee (All Hub)(801-xxx)
3/4" x 3/4" x 1/2"	1" x 1" x 1/2"	1" x 1" x 3/4"	1 1/4" x 1 1/4" x 1",
1 1/2" x 1 1/2" x 3/4"	1 1/2" x 1 1/2" x 1"	1 1/2" x 1 1/2" x 1 1/4"	2" x 2" x 1/2"
2" x 2" x 3/4"	2" x 2" x 1"	2" x 2" x 1 1/2"	3" x 3" x 2"
4" x 4" x 2"	4" x 4" x 3"	6" x 6" x 2"	6" x 6" x 4"
8" x 8" x 6"
PVC 8401 Tee(Hub x Hub x FPT)(802-xxx)
1/2"	3/4"	1"
PVC 8300 90° Elbow (Hub x Hub)(806-xxx)
1/2"	3/4"	1"	1 1/4"
1 1/2"	2"	2 1/2"	3"
4"	6"	8"	10"
12"
PVC 8301 90° Elbow (Hub x FPT)(807-xxx)
1/2"	3/4"	1"	1 1/4"
1 1/2"	2"
PVC 8309 45° Elbow (Hub x Hub)(817-xxx)
1/2"	3/4"	1"	1 1/4"
1 1/2"	2"	2 1/2"	3"
4"	6"	8"	10"
12"
PVC 8100 Coupling (Hub x Hub)(829-xxx)
1/2"	3/4"	1"	1 1/4"
1 1/2"	2"	2 1/2"	3"
4"	6"	8"	10"
12"
PVC 8100 Reducer Coupling (Hub x Hub)(829-xxx)
3/4" x 1/2"	1" x 1/2"	1" x 3/4"	1 1/4" x 1"
1 1/2" x 1"	1 1/2" x 1 1/4"	2" x 1"	2" x 1 1/2"
3" x 2"	4" x 2"	4" x 3"	6" x 4"
8" x 6"
PVC 8101 Female Adapter (Hub x FPT)(835-xxx)
1/2"	3/4"	1"	1 1/4"
1 1/2"	2"	2 1/2"	3"
4"
PVC 8109 Male Adapter (Hub x MPT)(836-xxx)
1/2"	3/4"	1"	1 1/4"
1 1/2"	2"	2 1/2"	3"
4"
PVC 8107 Reducer Bushing (SPG x Hub)(837-xxx)
3/4" x 1/2"	1" x 1/2"	1" x 3/4"	1 1/4" x 1/2"
1 1/4" x 3/4"	1 1/4" x 1"	1 1/2" x 1/2"	1 1/2" x 3/4"
1 1/2" x 1"	1 1/2" x 1 1/4"	2" x 1/2"	2" x 3/4"
2" x 1"	2" x 1 1/4"	2" x 1 1/2"	2 1/2" x 1"
2 1/2" x 1 1/4"	2 1/2" x 1 1/2"	2 1/2 x 2"	3" x 1"
3" x 1 1/4"	3" x 1 1/2"	3" x 2"	3" x 2 1/2"
4" x 2"	4" x 3"	6" x 3"	6" x 4"
8" x 6"	10" x 8"	12" x 10"
PVC 8108 Reducer Bushing (Spg x FPT)(838-xxx)
3/4" x 1/2"	1" x 1/2"	1" x 3/4"	1 1/4" x 3/4"
1 1/4" x 1"	1 1/2" x 1/2"	1 1/2" x 3/4"	1 1/2" x 1"
1 1/2" x 1 1/4"	2" x 1/2"	2" x 3/4"	2" x 1"
2" x 1 1/4"	2" x 1 1/2"	2 1/2" x 1 1/2"	2 1/2 x 2"
3" x 2"	3" x 2 1/2"	4" x 2"	4" x 3"
6" x 4"
PVC 8116 Cap (Socket)(847-xxx)
1/2"	3/4"	1"	1 1/4"
1 1/2"	2"	2 1/2"	3"
4"	6"	8"
PVC 8402 Tee (FPT x FPT x FPT)(805-xxx)
1/2"	3/4"	1"	1 1/4"
1 1/2"	2"	2 1/2"	3"
4"
PVC 8302 90° Elbow (FPT x FPT)(808-xxx)
1/2"	3/4"	1"	1 1/4"
1 1/2"	2"	2 1/2"	3"
4"
PVC 8312 45° Elbow (FPT x FPT)(819-xxx)
1/2"	3/4"	1"	1 1/4"
1 1/2"	2"	2 1/2"	3"
4"
PVC 8102 Coupling (FPT x FPT)(830-xxx)
1/2"	3/4"	1"	1 1/4"
1 1/2"	2"	2 1/2"	3"
4"
PVC 8117 Cap (FPT)(848-xxx)
1/2"	3/4"	1"	1 1/4"
1 1/2"	2"	2 1/2"	3"
4"
PVC 8200 Reducer Bushing (MPT x FPT)(839-xxx)
3/4"x 1/2"	1"x 1/2"	1"x 3/4"	1 1/4"x 3/4"
1 1/4"x 1"	1 1/2"x 1/2"	1 1/2"x 3/4"	1 1/2"x 1"
1 1/2"x 1 1/4"	2"x 1/2"	2"x 3/4"	2"x 1"
2"x 1 1/4"	2"x 1 1/2"	2 1/2"x 1 1/2"	2 1/2 x 2"
3"x 2"	3"x 2 1/2"	4"x 2"	4"x 3"
PVC 8113 Plug (MPT)(850-xxx)
1/2"	3/4"	1"	1 1/4"
1 1/2"	2"	2 1/2"	3"
4"
PVC 8600 Wye (All Hub)(875-xxx)
1 1/2"	2"	3"	4"
6"
+ Material complies with NSF/ANSI/CAN 61 health effects requirements when tested at 73° F. [G] Product is Certified to NSF/ANSI/CAN 372 and conforms with the lead content requirements for "lead free" plumbing as defined by California, Vermont, Maryland, and Louisiana state laws and the U.S. Safe Drinking Water Act. ****** These fitting products may also be represented by the trade names: Charlotte, Charlotte Pipe and Foundry Company®, Charlotte Pipe®, Charlotte Plastics®, Charlotte®, and Char®.
Fittings+ ^ [G]	PVC	CPF®******	ASTM F1970
PVC 2700 Sch 40 Union w/Viton O-Ring (HxH)
1/2"	3/4"	1"	1 1/4"
1 1/2"	2"
PVC 2710 Sch 40 Union w/EPDM O-Ring (HxH)
1/2"	3/4"	1"	1 1/4"
1 1/2"	2"
PVC 2800 Sch 40 Union w/Viton O-Ring (FTPxFTP)
1/2"	3/4"	1"	1 1/4"
1 1/2"	2"
PVC 2810 Sch 40 Union w/EPDM O-Ring (FTPxFTP)
1/2"	3/4"	1"	1 1/4"
1 1/2"	2"
PVC 2820 Sch 40 Union w/Viton O-Ring (HxFPT)
1/2"	3/4"	1"	1 1/4"
1 1/2"	2"
PVC 2830 Sch 40 Union w/EPDM O-Ring (HxFTP)
1/2"	3/4"	1"	1 1/4"
1 1/2"	2"
PVC 8710 Sch 80 Union w/EPDM O-Ring (Hub x Hub)
1/2"	3/4"	1"	1 1/4"
1 1/2"	2"	3"
PVC 8830 Sch 80 Union w/EPDM O-Ring Seal (HubxFPT)
1/2"	3/4"	1"	1 1/4"
1 1/2"	2"	3"
PVC 8700 Sch 80 Union w/Viton O-Ring Hub x Hub
1/2"	3/4"	1"	1 1/4"
1 1/2"	2"	3"
PVC 8810 Sch 80 Union w/EPDM O-Ring FPT x FPT
1/2"	3/4"	1"	1 1/4"
1 1/2"	2"	3"
PVC 8800 Sch 80 Union w/Viton O-Ring FPT x FPT
1/2"	3/4"	1"	1 1/4"
1 1/2"	2"	3"
PVC 8820 Sch 80 Union w/Viton O-Ring Hub x FPT
1/2"	3/4"	1"	1 1/4"
1 1/2"	2	3"
+ Material complies with NSF/ANSI/CAN 61 health effects requirements when tested at 73° F. ^ PVC and CPVC unions rated at 235 psi @ 73°F [G] Product is Certified to NSF/ANSI/CAN 372 and conforms with the lead content requirements for "lead free" plumbing as defined by California, Vermont, Maryland, and Louisiana state laws and the U.S. Safe Drinking Water Act. ****** These fitting products may also be represented by the trade names: Charlotte, Charlotte Pipe and Foundry Company®, Charlotte Pipe®, Charlotte Plastics®, Charlotte®, and Char®.
Fittings+ [G]	PVC	CPF® ******	ASTM D2609
PVC 2111 Insert Adapters
3/4"	1"	1 1/2"
+ Material complies with NSF/ANSI/CAN 61 health effects requirements when tested at 73° F. [G] Product is Certified to NSF/ANSI/CAN 372 and conforms with the lead content requirements for "lead free" plumbing as defined by California, Vermont, Maryland, and Louisiana state laws and the U.S. Safe Drinking Water Act.

Reclaimed Water - Pipe and Fittings

Product Type	Material Type	Trade Name	Product Standard
Pipe §*	PVC	Charlotte Pipe®***	ASTM D2241
3/4" - 6" SDR 21
2 1/2" - 12" SDR 32.5
4" - 12" SDR 41
* Sockets and gasketed bell ends are not tested or Listed by NSF for this production facility. § Product is Certified to the Uniform Plumbing Code™. Installation in accordance with the manufacturer's instructions and the requirements of the latest edition of the Uniform Plumbing Code™. *** These pipe products may include the production location code PLFL in the trade name.
Pipe §*	PVC	Charlotte Pipe®***	ASTM D1785
3/4" - 6" Sch 40
* Sockets and gasketed bell ends are not tested or Listed by NSF for this production facility. § Product is Certified to the Uniform Plumbing Code™. Installation in accordance with the manufacturer's instructions and the requirements of the latest edition of the Uniform Plumbing Code™. *** These pipe products may include the production location code PLFL in the trade name.

Well Casings

Product Type	Material Type	Trade Name	Product Standard
Well Casings§ [G]	PVC	Charlotte Pipe®***	ASTM F480
4.500" IC-1
6.250" IC-1
§ Product is Certified to the Uniform Plumbing Code™. Installation in accordance with the manufacturer's instructions and the requirements of the latest edition of the Uniform Plumbing Code™. *** These pipe products may include the production location code PLNC in the trade name. [G] Product is Certified to NSF/ANSI/CAN 372 and conforms with the lead content requirements for "lead free" plumbing as defined by California, Vermont, Maryland, and Louisiana state laws and the U.S. Safe Drinking Water Act.
Well Casings§ [G]	PVC	Charlotte Pipe®***	ASTM F480
2" - 14", 16" Sch 40
4", 6" SDR 26
4", 6" - 14", 16" SDR 21
§ Product is Certified to the Uniform Plumbing Code™. Installation in accordance with the manufacturer's instructions and the requirements of the latest edition of the Uniform Plumbing Code™. *** These pipe products may include the production location code PLNC in the trade name. [G] Product is Certified to NSF/ANSI/CAN 372 and conforms with the lead content requirements for "lead free" plumbing as defined by California, Vermont, Maryland, and Louisiana state laws and the U.S. Safe Drinking Water Act.

Drain, Waste, and Vent, Continuous Waste, and Sewer Materials

Material Type	End Use	Trade Name	Product Standard
PVC	2, 5	CP-430-M	ASTM D1784 12454

Potable Water - Materials

Material Type	End Use	Trade Name	Product Standard
PVC+	2	CP-430-M	ASTM D1784 12454
+ Material complies with NSF/ANSI/CAN 61 health effects requirements when tested at 73° F.

Facility : Muncy, PA

Drain, Waste, and Vent - Pipe and Fittings

Product Type	Material Type	Trade Name	Product Standard
Pipe§	MLTPL	Charlotte Pipe®	ASTM F1488
1 1/4" - 6" DR 24
§ Product is Certified to the Uniform Plumbing Code™. Installation in accordance with the manufacturer's instructions and the requirements of the latest edition of the Uniform Plumbing Code™.
Pipe §*	PVC	Charlotte Pipe®***	ASTM D2665
1 1/4" - 12" Sch 40
* Socketed and gasketed bell ends are not tested or Listed by NSF for this production facility. § Product is Certified to the Uniform Plumbing Code™. Installation in accordance with the manufacturer's instructions and the requirements of the latest edition of the Uniform Plumbing Code™. *** These pipe products may include the production location code PLPA in the trade name.
Pipe¢ §	ABS	Charlotte Pipe®***	ASTM F628
1 1/4" - 6" Sch 40
¢ Product is authorized to bear the cNSF and/or the cNSFus Mark. § Product is Certified to the Uniform Plumbing Code™. Installation in accordance with the manufacturer's instructions and the requirements of the latest edition of the Uniform Plumbing Code™. *** These pipe products may include the production location code PLPA in the trade name.
Pipe~	ABS	Charlotte Pipe®***	CSA B181.1
1 1/4" - 6" Sch 40
~ Product is authorized to bear the cNSF Mark. *** These pipe products may include the production location code PLPA in the trade name.
Pipe§	PVC	Charlotte Pipe®***	ASTM F891
1 1/2" - 8" Sch 40
10", 12" Sch 40
§ Product is Certified to the Uniform Plumbing Code™. Installation in accordance with the manufacturer's instructions and the requirements of the latest edition of the Uniform Plumbing Code™. *** These pipe products may include the production location code PLPA in the trade name.
Pipe	PVC	Charlotte Pipe®***	ASTM D2949
3 1/4"
*** These pipe products may include the production location code PLPA in the trade name.

Potable Water - Pipe and Fittings

Product Type	Material Type	Trade Name	Product Standard
Pipe + § [G]*	PVC	Charlotte Pipe®***	ASTM D1785
1/2" - 6" Sch 40
1/2" - 8" Sch 80
8" - 12" Sch 40
* Sockets and gasketed bell ends are not tested or Listed by NSF for this production facility. + Material complies with NSF/ANSI/CAN 61 health effects requirements when tested at 73° F. § Product is Certified to the Uniform Plumbing Code™. Installation in accordance with the manufacturer's instructions and the requirements of the latest edition of the Uniform Plumbing Code™. *** These pipe products may include the production location code PLPA in the trade name. [G] Product is Certified to NSF/ANSI/CAN 372 and conforms with the lead content requirements for "lead free" plumbing as defined by California, Vermont, Maryland, and Louisiana state laws and the U.S. Safe Drinking Water Act.
Pipe + § [G]*	PVC	Charlotte Pipe®***	ASTM D2241
1/2" SDR 13.5
3/4" - 2" SDR 21
1" - 6" SDR 26
2 1/2" - 12" SDR 32.5
4" - 12" SDR 41
* Sockets and gasketed bell ends are not tested or Listed by NSF for this production facility. + Material complies with NSF/ANSI/CAN 61 health effects requirements when tested at 73° F. § Product is Certified to the Uniform Plumbing Code™. Installation in accordance with the manufacturer's instructions and the requirements of the latest edition of the Uniform Plumbing Code™. *** These pipe products may include the production location code PLPA in the trade name. [G] Product is Certified to NSF/ANSI/CAN 372 and conforms with the lead content requirements for "lead free" plumbing as defined by California, Vermont, Maryland, and Louisiana state laws and the U.S. Safe Drinking Water Act.

Well Casings

Product Type	Material Type	Trade Name	Product Standard
Well Casings+ [G]	PVC	Charlotte Pipe®***	ASTM F480
2" - 12" Sch 40
+ Material complies with NSF/ANSI/CAN 61 health effects requirements when tested at 73° F. *** These pipe products may include the production location code PLPA in the trade name. [G] Product is Certified to NSF/ANSI/CAN 372 and conforms with the lead content requirements for "lead free" plumbing as defined by California, Vermont, Maryland, and Louisiana state laws and the U.S. Safe Drinking Water Act.

Facility : Cameron, TX

Drain, Waste, and Vent - Pipe and Fittings

Product Type	Material Type	Trade Name	Product Standard
Pipe §*	PVC	Charlotte Pipe®***	ASTM D2665
1 1/4" - 12" Sch 40
* Sockets and gasketed bell ends are not tested or Listed by NSF for this production facility. § Product is Certified to the Uniform Plumbing Code™. Installation in accordance with the manufacturer's instructions and the requirements of the latest edition of the Uniform Plumbing Code™. *** These pipe products may include the production location code PLTX in the trade name.
Pipe§	PVC	Charlotte Pipe®***	ASTM F891
1 1/2" - 12" Sch 40
§ Product is Certified to the Uniform Plumbing Code™. Installation in accordance with the manufacturer's instructions and the requirements of the latest edition of the Uniform Plumbing Code™. *** These pipe products may include the production location code PLTX in the trade name.

Potable Water - Pipe and Fittings

Product Type	Material Type	Trade Name	Product Standard
Pipe § [G]*	PVC	Charlotte Pipe®***	ASTM D1785
1/2" - 8" Sch 80
1/2" - 12" Sch 40
* Sockets and gasketed bell ends are not tested or Listed by NSF for this production facility. § Product is Certified to the Uniform Plumbing Code™. Installation in accordance with the manufacturer's instructions and the requirements of the latest edition of the Uniform Plumbing Code™. *** These pipe products may include the production location code PLTX in the trade name. [G] Product is Certified to NSF/ANSI/CAN 372 and conforms with the lead content requirements for "lead free" plumbing as defined by California, Vermont, Maryland, and Louisiana state laws and the U.S. Safe Drinking Water Act.
Pipe § [G]*	PVC	Charlotte Pipe®***	ASTM D2241
1/2" SDR 13.5
3/4" - 2" SDR 21
1" - 6" SDR 26
2 1/2" - 12" SDR 32.5
4" - 12" SDR 41
* Sockets and gasketed bell ends are not tested or Listed by NSF for this production facility. § Product is Certified to the Uniform Plumbing Code™. Installation in accordance with the manufacturer's instructions and the requirements of the latest edition of the Uniform Plumbing Code™. *** These pipe products may include the production location code PLTX in the trade name. [G] Product is Certified to NSF/ANSI/CAN 372 and conforms with the lead content requirements for "lead free" plumbing as defined by California, Vermont, Maryland, and Louisiana state laws and the U.S. Safe Drinking Water Act.

Well Casings

Product Type	Material Type	Trade Name	Product Standard
Well Casings+ [G]	PVC	Charlotte Pipe®***	ASTM F480
2" - 12" Sch 40
+ Material complies with NSF/ANSI/CAN 61 health effects requirements when tested at 73° F. *** These pipe products may include the production location code PLTX in the trade name. [G] Product is Certified to NSF/ANSI/CAN 372 and conforms with the lead content requirements for "lead free" plumbing as defined by California, Vermont, Maryland, and Louisiana state laws and the U.S. Safe Drinking Water Act.

Facility : Cedar City, UT

Drain, Waste, and Vent - Pipe and Fittings

Product Type	Material Type	Trade Name	Product Standard
Fittings@ §	PVC	CPF®**	ASTM D2665
PVC 100 - Coupling (Hub x Hub)
1 1/4", 1 1/2", 2", 3", 4", 6", 8", 10", 12"
PVC 101 - Female Adapter (FPT x Hub)
1 1/4", 1 1/2", 2", 3", 4", 6", 8"
PVC 102 - Pipe Increaser-Reducer (Hub x Hub)
1 1/2"x2", 1 1/2"x3", 2"x3", 2"x4", 3"x4", 3"x6", 4"x6",4"x8", 4"x10", 4"x12"	6"x8", 6'x10", 6"x12", 8"x10", 8"x12", 10"x12"
PVC 103 - Trap Adapter-Male
1 1/2"	1 1/2" x 1 1/4"	2"
PVC 104 - Trap Adapter-Female (Hub x SLIP)
1 1/2"	1 1/2" x 1 1/4"	1 1/4"	2"
PVC 105 - Fitting Cleanout Adapter (SPG x FPT)
1 1/4", 1 1/2", 2", 3", 4", 6", 8"
PVC 105-X - Fitting Cleanout Adapter w/C.O. Plug
1 1/2", 2", 3", 4", 6", 8"
PVC 106 - Cleanout Plug (MPT)
1 1/2", 2", 3", 4", 6", 8", 10", 12"
PVC 107 - Flush Bushing (SPG x HUB)
1 1/2"x1 1/4", 2"x1 1/4", 2"x1 1/2", 3"x1 1/2", 3"x2", 4"x2"	4"x3", 6"x4", 8"x4", 8"x6", 10"x4", 10"x6", 10"x8", 12"x4", 12"x6", 12"x8"	12"x10"
PVC 108 - Flush Bushing{Cleanout Adapter}(SPGxFPT)
2" x 1 1/2, 8" x 6", 10" x 8", 12" x 8"
PVC 108X - Flush Bushing w/Plug
2" x 1 1/2", 10" x 8", 12" x 8"
PVC 109 - Male Adapter (Not accept a tail piece)
1 1/4", 1 1/4" x 1 1/2", 1 1/2", 1 1/2" x 1 1/4", 2", 3", 4"
PVC 110 - Flush Cleanout Plug (MPT)
2", 3", 4"
PVC 110B - Flush Cleanout Plug - Brass Insert
2", 3", 4"
PVC 111 - Male Adapter (SPG x MPT)
1 1/2"	1 1/2" x 1 1/4"	2"	3"
PVC 113 - Tray Pl Adp H
1 1/2"
PVC 116 - Cap (SOCKET)
1 1/2", 2", 3", 4", 6", 8", 10", 12"
PVC 117x - Adapter Coupling S&D Spigot/DWV Hub
4" x 3"
PVC 117–Adapter Coupling/Adapts S&D SPG to DWV SPG
3"	4" x 3", 4" x 4"
PVC 118 - Adapter Bushing
3", 4"
PVC 119 - No Hub Adapter (Slip x Hub)
1 1/2", 2", 2" x 1 1/2", 3", 4", 4" x 3"
PVC 122 - Spigot Adapter, Cast Iron (Hub x Hub)
2" x 2", 3" x 3", 4" x 4"
PVC 123 - Hub Adapter, Cast Iron (Hub x SPG)
2" x 2", 3" x 3", 4" x 4"
PVC 123-R-Hub Adapter,Cast Iron,Increaser(HubxSPG)
1 1/2" x 2", 3" x 4"
PVC 131 - Test Cap
1 1/2", 2", 3", 4"
PVC 300 - 1/4 Bend (Hub x Hub)
1 1/4", 1 1/2", 2", 3", 4", 6", 8", 10", 12"
PVC 300-R - 1/4 Bend, Reducing (Hub x Hub)
2" x 1 1/2"
PVC 302 - 1/4 Bend, Street (SPG x Hub)
1 1/4", 1 1/2", 2", 3", 4", 6", 8"
PVC 303 -1/4 Bend with Low Heel Inlet(HubxHubxHub)
3" x 3" x 1 1/2", 3" x 3" x 2", 4" x 4" x 2"
PVC 304 - Long Sweep 1/4 Bend (Hub x Hub)
1 1/2", 2", 3", 4", 6"
PVC 305 - Long Sweep 1/4 Bend W/High Heel Inlet
3" x 3" x 2"
PVC 307 - Long Sweep 1/4 Bend w/Low Heel Inlet
3" x 3" x 1 1/2"	3" x 3" x 2"
PVC 309 - Long Sweep 1/4 Bend, Street (Hub x SPG)
1 1/2", 2", 3", 4"
PVC 310–¼ Bend Street Low Heel Inlet (HubxSPGxHub)
3" x 3" x 2"
PVC 319 - 1/6 Bend (Hub x Hub)
1 1/2", 2", 3", 4"
PVC 320 - 1/6 Bend Street (Hub x SPG)
1 1/2", 2", 3", 4"
PVC 321 - 1/8 Bend (Hub x Hub)
1 1/4", 1 1/2", 2", 3", 4", 6", 8", 10", 12"
PVC 323 - 1/8 Bend, Street (SPG x Hub)
1 1/4", 1 1/2", 2", 3", 4", 6", 8", 10", 12"
PVC 324 - 1/16 Bend (Hub x Hub)
1 1/2", 2", 3", 4", 6", 8", 10", 12"
PVC 326 - 1/16 Bend, Street (SPG x Hub)
1 1/2", 2", 3", 4", 6"
PVC 327 - Double 1/4 Bend (Hub x Hub x Hub)
1 1/2", 2", 3", 2 x 1 1/2" x 1 1/2"
PVC 329 - Closet Bend, Reducing (Hub x Hub)
3" x 4"
PVC 330 - Closet Bend, Reducing (Hub x SPG)
3" x 4"
PVC 330-X-Closet Bend,Reducing w/Test Cap(HubxSPG)
3" x 4"
PVC 331 - Vent Ell (Hub x Hub)
1 1/2", 2", 3"
PVC 333 - Vent Ell, Street (Hub x SPG)
1 1/2", 2", 3"
PVC 400 - Sanitary Tee (All Hub)
1 1/4", 1 1/2", 2", 3", 4", 6", 8", 10", 12"
PVC 401 - Sanitary Tee, Reducing (All Hub)
2" x 1 1/2" x 1 1/2"	2" x 1 1/2" x 2"	2" x 2" x 1 1/2"	3" x 3" x 1 1/2"
3" x 3" x 2"	4" x 4" x 1 1/2"	4" x 4" x 2"	4" x 4" x 3"
6" x 6" x 4"	8" x 8" x 4"	8" x 8" x 6"	10" x 10" x 8"
12" x 12" x 8"	12" x 12" x 10"
PVC 403 - Sanitary Tee, Street (SPG x Hub x Hub)
1 1/2", 2", 3", 4"
PVC 404 -Sanitary Tee,Street,Reducing(SPGxHubxHub)
2"x2"x1 1/2", 3"x3"x1 1/2", 3"x3"x2", 4"x4"x2"
PVC 416 - Sanitary Tee w/Left Side Inlet (All Hub)
3" x 3" x 3" x 1 1/2"	3" x 3" x 3" x 2"	4" x 4" x 4" x 2"
PVC 417 - Sanitary Tee w/Right Side Inlet(All Hub)
3" x 3" x 3" x 1 1/2"	3" x 3" x 3" x 2"	4" x 4" x 4" x 2"
PVC 418–Sanitary Tee Right & Left Side Inlet (Hub)
3" x 3" x 3" x 2" x 2", 4" x 4" x 4" x 2" x 2"
PVC 428 - Double Sanitary Tee (All Hub)
1 1/2", 2", 3", 4"
PVC 429 - Double Sanitary Tee, Reducing (All Hub)
2" x 2" x 1 1/2"x1 1/2"	3" x 3"x 1 1/2"x1 1/2"	3" x 3" x 2" x 2"	4" x 4" x 1 1/2" x 1 1/2"
4" x 4" x 2" x 2"	4" x 4" x 3" x 3"
PVC 431–Dbl Sanitary Tee, St, Red. SPGxHubxHubxHub
3" x 3" x 1 1/2" x 1 1/2"
PVC 438 - Dbl Sanitary Tee w/ Side Inlet (All Hub)
3" x 3" x 3" x 3" x 2", 4" x 4" x 4" x 4" x 2"
PVC 439 - Dbl San Tee w/ Right & Left Side Inlets
3" x 3" x 3" x 3" x 2" x 2", 4" x 4" x 4" x 4" x 2" x 2"
PVC 441 - Vent Tee (All Hub)
1 1/2", 2", 3", 4", 6", 8"
PVC 444-X - Cleanout Tee w/ Cleanout Plug(HubxHub)
1 1/2", 2", 3", 4", 6", 8", 6" x 6" x 4", 8" x 8" x 6"	10" x 10" x 8", 12" x 12" x 6", 12" x 12" x 8"
PVC 445 - Flush Cleanout Tee (Hub x Hub x FPT)
1 1/2", 2", 3", 4", 6", 8", 10" x 10" x 8", 12" x 12" x 8"
PVC 445-X - Flush Tee w/ Cleanout Plug (Hub x Hub)
1 1/2", 2", 3", 4"
PVC 448 - Two-Way Cleanout (All Hub)
3", 4", 6"
PVC 449 - Sanitary Tee (All Hub)
2"
PVC 500 - Double Fixture Fitting (All Hub)
2", 3", 2" x 1 1/2" x 1 1/2" x 1 1/2", 2" x 2" x 1 1/2" x 1 1/2"
PVC 501 – Comb. Wye & 1/8 Bend-One Piece (All Hub)
1 1/2", 2", 3", 4"
PVC 502 - Comb Wye & 1/8 Bend, Reducer (All Hub)
2" x 1 1/2" x 1 1/2"	2" x 1 1/2" x 2"	2" x 2" x 1 1/2"	3" x 3" x 1 1/2"
3" x 3" x 2"	4" x 4" x 2"	4" x 4" x 3"
PVC 503 - Combination Wye and 1/8 Bend (H x H x H)
6" x 6" x 6"	8" x 8" x 8"	12" x 12" x 12"
PVC 504–Comb. Wye & 1/8 Bend Red., Two Piece (Hub)
4” x 4" x 3"	6" x 6" x 3"	6" x 6" x 4"	8" x 8" x 4"
8" x 8" x 6"	10" x 10" x 4"	10" x 10" x 6"	10" x 10" x 8"
12" x 12" x 4"	12" x 12" x 6"	12" x 12" x 8"	12" x 12" x 10"
PVC 507 - Dbl Combination Wye & 1/8 Bend (ALL HUB)
1 1/2", 2", 3", 4"	2" x 2" x 1 1/2" x 1 1/2"	3" x 3" x 2" x 2"	4" x 4" x 2" x 2"
4" x 4" x 3" x 3"	6" x 6" x 4" x 4"
PVC 515 - Comb Wye & 1/8 Bend w/ Left Side Inlet
3" x 3" x 3" x 2"
PVC 516–Comb. Wye & 1/8 Bend Rgt Side Inlet (Hub)
3" x 3" x 3" x 2"
PVC 517–Comb. Wye & 1/8 Bend Rgt & Lft Inlet (Hub)
3" x 3" x 3" x 2" x 2"
PVC 600 - Wye (All Hub)
1 1/4", 1 1/2", 2" 3",4",6", 8", 10", 12"
PVC 601 - Wye, Reducing (All Hub)
2" x 1 1/2" x 1 1/2"	2" x 1 1/2" x 2"	2" x 2" x 1 1/2"	3" x 3" x 1 1/2"
3" x 3" x 2"	4" x 4" x 1 1/2"	4" x 4" x 2"	4" x 4" x 3"
6" x 6" x 3"	6" x 6" x 4"	8" x 8" x 4"	8" x 8" x 6"
10" x 10" x 4"	10" x 10" x 6"	10" x 10" x 8"	12" x 12" x 4"
12" x 12" x 6"	12" x 12" x 8"	12" x 12" x 10"
PVC 602 - Wye, Street (SPG x Hub x Hub)
1 1/2", 2", 3", 4"
PVC 603 - Wye, Street, Reducing (SPG x Hub x Hub)
3" x 3" x 1 1/2"	3" x 3" x 2"	4" x 4" x 2"	4" x 4" x 3"
PVC 611 - Double Wye (ALL HUB)
1 1/2", 2", 3", 4", 6"
PVC 612 - Double Wye, Reducing (ALL HUB)
2" x 2" x 1 1/2" x 1 1/2"	3" x 3" x 1 1/2" x 1 1/2"	3" x 3" x 2" x 2"	4" x 4" x 2" x 2"
4" x 4" x 3" x 3"	6" x 6" x 4" x 4"
PVC 700 - Return Bend (Hub x Hub)
1 1/2", 2", 3", 4"
PVC 703P - Tray Adapter
1 1/2" x 1 1/4"
PVC 703X - Tray Adapter
1 1/2" x 1 1/4"
PVC 704P - Tail Piece Adpt.(SxSLIP w/ Plastic Nut)
1 1/2"
PVC 704X - Tail Piece Adpt. (SxSLIP w/ Chrome Nut)
1 1/2"
PVC 706-X - P-Trap (Hub x Hub)
1 1/2", 2", 3", 4"
PVC 707-X - P-Trap with Cleanout (Hub x Hub)
1 1/2", 2", 3", 4"
PVC 708-P - P-Trap (Hub x Hub with Plastic Nut)
1 1/4", 1 1/2", 2"
PVC 708-X - P-Trap (Hub x Hub with Chrome Nut)
1 1/2"
PVC 709-X - P-Trap w/Cleanout(HubxHubw/Chrome Nut)
1 1/2"
PVC 710 - Low Profile P-Trap w/Solvent Weld Joint
2"
PVC 711-X - L.A. Pattern P-Trap
1 1/2"
PVC 711P - L.A. Pattern P-Trap (Slip x Hub)
1 1/2"
PVC 800 - Closet Flange (Hub)
4" x 3", 4" x 4"
PVC 800KO - Closet Flange with Knock Out (Hub)
4" x 3", 4" x 4"
PVC 800s - Closet Flange with Stop (Hub)
4" x 3"
PVC 801 - Closet Flange, Reducing (SPIGOT)
4" x 3"
PVC 810-KO-Closet Flange,Adj w/PlasRing w-KnockOut
4" x 3"
PVC 811-KO-Closet Flange,Adj w/Metal/Plastic Ring
4" x 3"
PVC 811–Closet Flange, Adj Metal/Plastics Ring-Hub
4" x 3", 4" x 4"
PVC 812-Closet Flange, Adj w/ Metal/Plastic Ring
4" x 3", 4" x 4"
PVC 815-Flush Closet Flange-fits 3" or 4" (Hub)
4" x 4"/4" x 3"
PVC 815K-Flush Closet Flange w-Knock Out (Hub)
4" x 3"	4" x 4"
PVC 820-Offset Flange,Adj
4" x 3"
PVC 820P - Offset Flange, Adj Plastic Ring
4" x 3"
PVC 900 - Swivel Tray Plug Adp. w/ Washer(SpgxFPT)
1 1/2"
PVC 910 - Swivel Tray Plug Adp. w/ Washer (HxFPT)
1 1/2"
@ A letter after the part number designates the following: X - Metal Ring/Plastic Ring R - Reducing P - Plastic Ring W - Washer § Product is Certified to the Uniform Plumbing Code™. Installation in accordance with the manufacturer's instructions and the requirements of the latest edition of the Uniform Plumbing Code™. ** These pipe products may also be represented by the trade names: CPF, Charlotte, Charlotte Pipe, Charlotte Pipe and Foundry Company, or Charlotte Plastics.
Pipe§	MLTPL	CHARLOTTE PIPE® PLUT**	ASTM F1488
1 1/2" - 6" Sch 40
§ Product is Certified to the Uniform Plumbing Code™. Installation in accordance with the manufacturer's instructions and the requirements of the latest edition of the Uniform Plumbing Code™. ** These pipe products may also be represented by the trade names: CPF, Charlotte, Charlotte Pipe, Charlotte Pipe and Foundry Company, or Charlotte Plastics.
Pipe§	MLTPL	Charlotte Pipe®	ASTM F1488
1 1/4" - 6" DR 24
§ Product is Certified to the Uniform Plumbing Code™. Installation in accordance with the manufacturer's instructions and the requirements of the latest edition of the Uniform Plumbing Code™.
Pipe ¢ §*	ABS	Charlotte Pipe PLUT	ASTM F628
1 1/4" - 6" Sch 40
* Sockets and gasketed bell ends are not tested or Listed by NSF for this production facility. ¢ Product is authorized to bear the cNSF and/or the cNSFus Mark. § Product is Certified to the Uniform Plumbing Code™. Installation in accordance with the manufacturer's instructions and the requirements of the latest edition of the Uniform Plumbing Code™.
Pipe §*	PVC	Charlotte Pipe®***	ASTM D2665
1 1/4" - 16" Sch 40
* Sockets and gasketed bell ends are not tested or Listed by NSF for this production facility. § Product is Certified to the Uniform Plumbing Code™. Installation in accordance with the manufacturer's instructions and the requirements of the latest edition of the Uniform Plumbing Code™. *** These pipe products may include the production location code PLUT in the trade name.
Pipe §*	PVC	Charlotte Pipe®***	ASTM F891
1 1/4" - 6" Sch 40
* Sockets and gasketed bell ends are not tested or Listed by NSF for this production facility. § Product is Certified to the Uniform Plumbing Code™. Installation in accordance with the manufacturer's instructions and the requirements of the latest edition of the Uniform Plumbing Code™. *** These pipe products may include the production location code PLUT in the trade name.
Fittings@ §	ABS	CPF®****	ASTM D2661
ABS 100 - Coupling (Hub x Hub)
1 1/4", 1 1/2", 2", 3", 4", 6", 8", 10", 12"
ABS 101- Female Adapter (Hub x FTP)
1 1/2", 2", 3", 4", 6"
ABS 102 - Pipe Increaser - Reducer (Hub x Hub)
1 1/2" x 2"	1 1/2" x 3"	2" x 3"	2" x 4"
3" x 4"
ABS 103 - Trap Adapter-Male (SPG x SLIP)
1 1/2"	1 1/2" x 1 1/4"	2"
ABS 103P – Trap Adapter Male w/Plastic Nut
1 1/2"	1 1/2" x 1 1/4"
ABS 103R – Trap Adapter Male w/Plastic Nut
1 1/2"
ABS 103W – Trap Adapter Male w/Plas Nut-Washer
1 1/2"	1 1/2" x 1 1/4"	2"
ABS 103X – Trap Adapter Male w/Chrome Nut
1 1/2"	1 1/2" x 1 1/4"
ABS 104 - Trap Adapter-Female (Hub x Slip)
1 1/2"	1 1/2" x 1 1/4"	2"
ABS 104P – Trap Adapter Female w/Plastic Nut
1 1/2"	1 1/2" x 1 1/4"
ABS 104R – Trap Adapter Female w/Plast Washer-Nut
1 1/2"
ABS 104W –Trap Adapter Female w/Plastic Nut-Washer
1 1/2"	1 1/2" x 1 1/4"
ABS 104X – Trap Adapter Female w/Chrome Nut
1 1/2"	1 1/2" x 1 1/4"	2"
ABS 105 - Fitting Cleanout Adapter (SPG x FPT)
1 1/4", 1 1/2", 2", 3", 4"
ABS 105x - Fitting Cleanout Adapter w/C.O. Plug
1 1/2", 2", 3", 4"
ABS 106 - Cleanout Plug (MPT)
1 1/2", 2", 2 1/2", 3", 3 1/2", 4", 6", 8"
ABS 107 - Flush Bushing (SPG x Hub)
1 1/2" x 1 1/4"	2" x 1 1/4"	2" x 1 1/2"	3" x 1 1/2"
3" x 2"	4" x 2"	4" x 3"	6" x 4"
ABS 108 - Flush Bushing(Cleanout Adapter)(HubxFPT)
2" x 1 1/2" 6" x 4" 6" x 8"
ABS 109–Male Adptr- not accept tail pc (MPT x Hub)
1 1/2", 2", 3", 4"
ABS 110 - Flush C.O. Plug (MPT)
2", 3", 4"
ABS 111- Male Fitting Adapter (SPG x MPT)
1 1/2"	2"
ABS 113 - Tray Plug Adapter (Hub)
1 1/2"
ABS 113S - Tray Plug Adapter (SPG)
1 1/2"
ABS 114 - Threaded Cap (FPT)
1 1/2"
ABS 116 - Cap (Socket)
1 1/2", 2", 3", 4", 6"
ABS 117 - Adapter Coupling (Hub x Hub)
4" x 3"	4" x 4"
ABS 118 - Adapter Bushing (DWV SPG x Hub)
3", 4"
ABS 119 - No-Hub Adapter (SPG x Hub)
1 1/2", 2", 3", 4
ABS 122 - Spigot Adapter, Cast iron (Hub x Hub)
2" x 2"	4" x 4"
ABS 123 - Hub Adapter, Cast Iron (Hub x SPG)[1]
2" x 2"	4" x 4"
ABS 123R -Hub Adapter,Cast Iron,Increaser(HubxSPG)
1 1/2" x 2"	3" x 4"
ABS 131 - Test Cap
1 1/2", 2", 3", 4"
ABS 300 - 90° Elbows 1/4 Bend (Hub x Hub)
1 1/2", 2", 3", 4", 6"
ABS 300R - 90° Elbows 1/4 Bend, Reducing (HubxHub)
2" x 1 1/2"
ABS 300s–90° Elbow1/4Bend,with Side Inlet(All Hub)
3" x 3" x 2"
ABS 302 - 90° Elbows 1/4 Bend, Street (SPG x Hub)
1 1/2", 2", 3", 4"
ABS 303 - 90° Elbow 1/4 Bend w/Low Heel Inlet(Hub)
3" x 3" x 1 1/2"	3" x 3" x 2"	4" x 4" x 2"
ABS 303S - Elbow 1/4 Bend with Side Inlet
3" x 3" x 1 1/2"
ABS 304 - 90° Elbows Long Sweep 1/4 Bend (HubxHub)
1 1/2", 2", 3", 4"
ABS 305 - 90° Elbow Long Sweep ¼Bend w/ Inlet(Hub)
3" x 3" x 2"
ABS 307 - 90° Elbow Long Sweep ¼Bend w/Inlet(Hub)
3" x 3" x 1 1/2"	3" x 3" x 2"
ABS 309-90° Elbow Long Sweep ¼Bend,Street(HubxSPG)
1 1/2", 2", 3"
ABS 310–90° Elbow ¼ Bend LowHeelInlet HubxSPG xHub
3" x 3" x 2"
ABS 311–90° Elbow Long Swp ¼ Bend Side Inlet (Hub)
3" x 3" x 2"
ABS 319 - 60° Elbow 1/6 Bend (Hub x Hub)
1 1/2", 2", 3", 4"
ABS 320 - 60º Elbow 1/6 Bend, Street (SPG x Hub)
1 1/2", 2", 3"
ABS 321 - 45° Elbows 1/8 Bend (Hub x Hub)
1 1/2", 2", 3", 4", 6"
ABS 323 - 45º Elbows 1/8 Bend, Street (SPG x Hub)
1 1/2", 2", 3", 4", 6"
ABS 324 - 22 1/2° Elbow 1/16 Bend (Hub x Hub)
1 1/2", 2", 3", 4", 6"
ABS 326 - 22 1/2° Elbow 1/16 Bend Street (SPGxHub)
1 1/2", 2", 3", 4"
ABS 327 - 90° Elbows Double 1/4 bend (ALL HUB)
1 1 /2", 2", 3", 2" x 1 1/2" x 1 1/2"
ABS 328X - Closet Bend Short w/Test Cap
3" x 4"
ABS 329 - Closet Bend, Reducing (Hub x Hub)
3" x 4"
ABS 330 - Closet Bend, Reducing (Hub x SPG)
3" x 4"
ABS 330x-Closet Bend Reducing w/ Test Cap(HubxSPG)
3" x 4"
ABS 331 - Vent Ell (Hub x Hub)
1 1/2", 2", 3"
ABS 333 - Vent Ell, Street (Hub x SPG)
1 1/2", 2"
ABS 400 - Sanitary Tee (ALL HUB)
1 1/2", 2", 3", 4", 6"
ABS 401 - Sanitary Tee, Reducing (All Hub)
2" x 1 1/2" x 1 1/2"	2" x 1 1/2" x 2"	2" x 2" x 1 1/2"	3" x 3" x 1 1/2"
3" x 3" x 2"	4" x 4" x 2"	4" x 4" x 3"	6" x 6" x 4"
ABS 403 - Sanitary Tee, Street (SPG x Hub x Hub)
1 1/2", 2", 3", 4"
ABS 404 -Sanitary Tee,Street,Reducing(SPGxHubxHub)
2" x 1 1/2" x 1 1/2"	2" x 1 1/2" x 2"	2" x 2" x 1 1/2"	3" x 3" x 1 1/2"
3" x 3" x 2"
ABS 416 - Sanitary Tee with Left Side Inlet (Hub)
3" x 3" x 3" x 2", 3" x 3" x 3" x 1 1/2"
ABS 417 – Sanitary Tee w/Right Side Inlet(All Hub)
3" x 3" x 3" x 1 1/2"	3" x 3" x 3" x 2"
ABS 418 - Sanitary Tee w/R & L Side Inlet (Hub)
3" x 3" x 3" x 2" x 2"	4" x 4" x 4" x 2" x 2"
ABS 428 - Double Sanitary Tee (All Hub)
1 1/2", 2", 3", 4"
ABS 429 - Double Sanitary Tee, Reducing (All Hub)
2" x 2" x 1 1/2" x 1 1/2"	3" x 3" x 1 1/2" x 1 1/2"	3" x 3" x 2" x 2"	4" x 4" x 2" x 2"
4" x 4" x 3" x 3"
ABS 438 - Dbl Sanitary Tee w/Side Inlet (Hub)
3" x 3" x 3" x 3" x 2"	4" x 4" x 4" x 4" x 2"
ABS 439 - Dbl Sanitary Tee w/R&LSide Inlets (Hub)
3" x 3" x 3" x 3" x 2" x 2"	4" x 4" x 4" x 4" x 2" x 2"
ABS 441 - Vent Tee (All Hub)
1 1/2", 2", 3"
ABS 444x - Cleanout Tee w/ Cleanout Plug (HubxHub)
1 1/2", 2", 3", 4", 6"
ABS 445 - Flush Cleanout Tee (Hub x Hub x FPT)
1 1/2", 2", 3", 4", 6"
ABS 447 - Horizontal Twin Tee (All Hub)
3" x 3" x 1 1/2" x 1 1/2"
ABS 448 - Two-Way Cleanout (All Hub)
3", 4"
ABS 500 - Double Fixture Fitting (All Hub)
2" x 1 1/2" x 1 1/2" x 1 1/2"	2" x 1 1/2" x 2" x 2"	2" x 2" x 1 1/2" x 1 1/2"	2", 3"
3" x 2" x 3"x 3"
ABS 501 - Comb Wye and 1/8 Bend (All Hub)
1 1/2", 2", 3", 4"
ABS 502-Comb Wye & 1/8 Bend, Reducing One Pc.(Hub)
2" x 1 1/2" x 1 1/2"	2" x 1 1/2" x 2"	2" x 2" x 1 1/2"	3" x 3" x 1 1/2"
3" x 3" x 2"	4" x 4" x 2"	4" x 4" x 3"
ABS 600 - Wye (ALL HUB)
1 1/2", 2", 3", 4", 6"
ABS 601 - Wye, Reducing (All Hub)
2" x 1 1/2" x 1 1/2"	2" x 1 1/2" x 2"	2" x 2" x 1 1/2"	3" x 3" x 1 1/2"
3" x 3" x 2"	4" x 4" x 1 1/2"	4" x 4" x 2"	4" x 4" x 3"
6" x 6" x 4"
ABS 602 - Wye, Street (SPG x Hub x Hub)
1 1/2", 2", 3", 4"
ABS 603 - Wye, Street, Reducing (SPG x Hub x Hub)
3" x 3" x 1 1/2"	3" x 3" x 2"	4" x 4" x 3"
ABS 611 - Double Wye (All Hub)
1 1/2", 2", 3", 4"
ABS 612 - Double Wye, Reducing (All Hub)
2" x 2" x 1 1/2" x 1 1/2"	3" x 3" x 1 1/2" x 1 1/2"	3" x 3" x 2" x 2"	4" x 4" x 3" x 3"
ABS 700 - Return Bend (Hub x Hub)
1 1/2", 2", 3", 4"
ABS 704 - Tail Piece Adapter (SPG x Slip)
1 1/2"
ABS 704P-Tail Piece Adapter(SPGxSlip)w/Plastic Nut
1 1/2"
ABS 706x - P-Trap (Hub x Hub)
1 1/2", 2", 3", 4"
ABS 707x - P-Trap with Cleanout (Hub x Hub)
1 1/2", 2"
ABS 708P - P-Trap (Hub x Hub with Plastic Nut)
1 1/2", 2"
ABS 708x - P-Trap (Hub x Hub with Chrome Nut)
1 1/2"
ABS 710-DWV Low Profile P-Trap w/Solvent Weld Jnt
2"
ABS 711P - L.A. Pattern P-Trap (Slip x Hub)[3]
1 1/2"
ABS 711W-L.A. Pattern P-Trap Plstc Nut (SlipxHub)[3]
1 1/2"
ABS 720X-Drum Trap with Cleanout
3" x 6" x 1 1/2"
ABS 800 - Closet Flange (Hub)
4" x 3"	4" x 4"
ABS 800Ko - Closet Flange with Knock Out (Hub)
4" x 3"
ABS 800S - Closet Flange with Stop (Hub)
4" x 3"
ABS 801 - Closet Flange, Reducing (SPG)
4" x 3"
ABS 808 - Closet Flange, Male (MPT)
4" x 3"
ABS 811-KO-Closet Flange, Adj w/Meta/Plasticl Ring
4" x 3"
ABS 811–Closet Flange, Adj Metal/Plstc Ring (Hub)
4" x 3"	4" x 4"
ABS 811P - Closet Flange, Adj w/ABS Ring
4" x 3", 4" x 4"
ABS 812-Closet Flange, Adj
4" x 3"	4" x 4"
ABS 812P - Closet Flange, Adj Plastic Ring
4" x 3"
ABS 815 - Flush Closet Flange
4" x 4"/4" x 3"
ABS 815Ko - Flush Closet Flange with Knockout[2]
4" x 4"/4" x 3"
ABS 820-Offset Flange, Adj
4" x 3"
ABS 820P - Offset Flange, Adj Plastic Ring
4" x 3"
ABS 824-Closet Flange, Adjust. w/Metal Ring
4"
ABS 900-Swivel Tray Plug Adapter w/Washer(SPGxFPT)
1 1/2"
ABS 900x - ABS Ext Swivel Tray Adp
1 1/2"
ABS 910-Swivel Tray Plug Adapter w/Washer(SPGxFPT)
1 1/2"
[1] Plain End: Joint can be made with compression gasket only. [3] Furnished with 1 1/2 and 1 1/2 x 1 1/4 Polyethylene nut/washer combination. [2] Fits Over 3'' Pipe or Inside 4'' Pipe. @ A letter after the part number designates the following: X - Metal Ring/Plastic Ring R - Reducing P - Plastic Ring W - Washer § Product is Certified to the Uniform Plumbing Code™. Installation in accordance with the manufacturer's instructions and the requirements of the latest edition of the Uniform Plumbing Code™. **** These fitting products may also be represented by the trade names: Charlotte Pipe and Foundry Company®, Charlotte Plastics®, Charlotte Pipe®, Charlotte®, Charlotte or Char®.
Fittings@ ¢	ABS	CPF®****	CSA B181.1
ABS 100 - Coupling (Hub x Hub)
1 1/4", 1 1/2", 2", 3", 4", 6", 8", 10", 12"
ABS 101- Female Adapter (Hub x FTP)
1 1/2", 2", 3", 4", 6"
ABS 102 - Pipe Increaser - Reducer (Hub x Hub)
2" x 4"	3" x 4"	2" x 3"	1 1/2" x 2"
1 1/2" x 3"
ABS 103 - Trap Adapter-Male (SPG x SLIP)
1 1/2"	1 1/2" x 1 1/4"	2"
ABS 103P – Trap Adapter Male w/Plastic Nut
1 1/2"	1 1/2" x 1 1/4"
ABS 103R – Trap Adapter Male w/Plastic Nut
1 1/2"
ABS 103W – Trap Adapter Male w/Plas Nut-Washer
1 1/2"	1 1/2" x 1 1/4"	2"
ABS 103X – Trap Adapter Male w/Chrome Nut
1 1/2"	1 1/2" x 1 1/4"
ABS 104 - Trap Adapter-Female (Hub x Slip)
1 1/2"	1 1/2" x 1 1/4"	2"
ABS 104P – Trap Adapter Female w/Plastic Nut
1 1/2" x 1 1/4"	1 1/2"
ABS 104R – Trap Adapter Female w/Plast Washer-Nut
1 1/2"
ABS 104W –Trap Adapter Female w/Plastic Nut-Washer
1 1/2"	1 1/2" x 1 1/4"
ABS 104X – Trap Adapter Female w/Chrome Nut
1 1/2"	1 1/2" x 1 1/4"	2"
ABS 107 - Flush Bushing (SPG x Hub)
1 1/2" x 1 1/4"	2" x 1 1/4"	2" x 1 1/2"	3" x 1 1/2"
3" x 2"	4" x 2"	4" x 3"	6" x 4"
ABS 109–Male Adptr- not accept tail pc (MPT x Hub)
1 1/2", 2", 3", 4"
ABS 111- Male Fitting Adapter (SPG x MPT)
2"	1 1/2"
ABS 113 - Tray Plug Adapter (Hub)
1 1/2"
ABS 113S - Tray Plug Adapter (SPG)
1 1/2"
ABS 114 - Threaded Cap (FPT)
1 1/2"
ABS 116 - Cap (Socket)
1 1/2", 2", 3", 4", 6"
ABS 117 - Adapter Coupling (Hub x Hub)
4" x 4"	4" x 3"
ABS 118 - Adapter Bushing (DWV SPG x Hub)
3", 4"
ABS 119 - No-Hub Adapter (SPG x Hub)
1 1/2", 2", 3", 4"	4" x 3"
ABS 122 - Spigot Adapter, Cast iron (Hub x Hub)
2" x 2"	4" x 4"
ABS 123 - Hub Adapter, Cast Iron (Hub x SPG)[1]
2" x 2"	4" x 4"
ABS 123R -Hub Adapter,Cast Iron,Increaser(HubxSPG)
1 1/2" x 2"	3" x 4"
ABS 130 - Repair Coupling (Hub x Hub)
1 1/2", 2", 3", 4", 6"
ABS 131 - Test Cap
1 1/2", 2", 3", 4"
ABS 300 - 90° Elbows 1/4 Bend (Hub x Hub)
1 1/2", 2", 3", 4", 6"
ABS 300R - 90° Elbows 1/4 Bend, Reducing (HubxHub)
2" x 1 1/2"
ABS 300s–90° Elbow1/4Bend,with Side Inlet(All Hub)
3" x 3" x 2"
ABS 302 - 90° Elbows 1/4 Bend, Street (SPG x Hub)
1 1/2", 2", 3", 4"
ABS 303 - 90° Elbow 1/4 Bend w/Low Heel Inlet(Hub)
3" x 3" x 1 1/2"	3" x 3" x 2"	4" x 4" x 2"
ABS 303S - Elbow 1/4 Bend with Side Inlet
3" x 3" x 1 1/2"
ABS 304 - 90° Elbows Long Sweep 1/4 Bend (HubxHub)
1 1/2", 2", 3", 4"
ABS 305 - 90° Elbow Long Sweep ¼Bend w/ Inlet(Hub)
3" x 3" x 2"
ABS 307 - 90° Elbow Long Sweep ¼Bend w/Inlet(Hub)
3" x 3" x 1 1/2"	3" x 3" x 2"
ABS 309-90° Elbow Long Sweep ¼Bend,Street(HubxSPG)
1 1/2", 2", 3"
ABS 310–90° Elbow ¼ Bend LowHeelInlet HubxSPG xHub
3" x 3" x 2"
ABS 311–90° Elbow Long Swp ¼ Bend Side Inlet (Hub)
3" x 3" x 2"
ABS 319 - 60° Elbow 1/6 Bend (Hub x Hub)
1 1/2", 2", 3", 4"
ABS 320 - 60º Elbow 1/6 Bend, Street (SPG x Hub)
1 1/2", 2", 3"
ABS 321 - 45° Elbows 1/8 Bend (Hub x Hub)
1 1/2", 2", 3", 4", 6"
ABS 323 - 45º Elbows 1/8 Bend, Street (SPG x Hub)
1 1/2", 2", 3", 4", 6"
ABS 324 - 22 1/2° Elbow 1/16 Bend (Hub x Hub)
1 1/2", 2", 3", 4", 6"
ABS 326 - 22 1/2° Elbow 1/16 Bend Street (SPGxHub)
1 1/2", 2", 3", 4"
ABS 327 - 90° Elbows Double 1/4 bend (ALL HUB)
1 1 /2", 2", 3", 2" x 1 1/2" x 1 1/2"
ABS 328X - Closet Bend Short w/Test Cap
3" x 4"
ABS 329 - Closet Bend, Reducing (Hub x Hub)
3" x 4"
ABS 330 - Closet Bend, Reducing (Hub x SPG)
3" x 4"
ABS 330x-Closet Bend Reducing w/ Test Cap(HubxSPG)
3" x 4"
ABS 331 - Vent Ell (Hub x Hub)
1 1/2", 2", 3"
ABS 333 - Vent Ell, Street (Hub x SPG)
1 1/2", 2"
ABS 400 - Sanitary Tee (ALL HUB)
1 1/2", 2", 3", 4", 6"
ABS 401 - Sanitary Tee, Reducing (All Hub)
2" x 1 1/2" x 1 1/2"	2" x 1 1/2" x 2"	2" x 2" x 1 1/2"	3" x 3" x 1 1/2"
3" x 3" x 2"	4" x 4" x 2"	4" x 4" x 3"	6" x 6" x 4"
ABS 403 - Sanitary Tee, Street (SPG x Hub x Hub)
1 1/2", 2", 3", 4"
ABS 404 -Sanitary Tee,Street,Reducing(SPGxHubxHub)
2" x 1 1/2" x 1 1/2"	2" x 1 1/2" x 2"	2" x 2" x 1 1/2"	3" x 3" x 1 1/2"
3" x 3" x 2"
ABS 416 - Sanitary Tee with Left Side Inlet (Hub)
3" x 3" x 3" x 2", 3'' x 3'' x 3'' x 1 1/2''
ABS 417 – Sanitary Tee w/Right Side Inlet(All Hub)
3" x 3" x 3" x 1 1/2"	3" x 3" x 3" x 2"
ABS 418 - Sanitary Tee w/R & L Side Inlet (Hub)
3" x 3" x 3" x 2" x 2"	4" x 4" x 4" x 2" x 2"
ABS 428 - Double Sanitary Tee (All Hub)
1 1/2", 2", 3", 4"
ABS 429 - Double Sanitary Tee, Reducing (All Hub)
2" x 2" x 1 1/2" x 1 1/2"	3" x 3" x 1 1/2" x 1 1/2"	3" x 3" x 2" x 2"	4" x 4" x 2" x 2"
4" x 4" x 3" x 3"
ABS 438 - Dbl Sanitary Tee w/Side Inlet (Hub)
3" x 3" x 3" x 3" x 2"	4" x 4" x 4" x 4" x 2"
ABS 439 - Dbl Sanitary Tee w/R&LSide Inlets (Hub)
3" x 3" x 3" x 3" x 2" x 2"	4" x 4" x 4" x 4" x 2" x 2"
ABS 441 - Vent Tee (All Hub)
1 1/2", 2", 3"
ABS 447 - Horizontal Twin Tee (All Hub)
3" x 3" x 1 1/2" x 1 1/2"
ABS 448 - Two-Way Cleanout (All Hub)
3", 4"
ABS 500 - Double Fixture Fitting (All Hub)
2", 3"	2" x 1 1/2" x 1 1/2" x 1 1/2"	2" x 1 1/2" x 2" x 2"	2" x 2" x 1 1/2" x 1 1/2"
3" x 2" x 3" x 3"
ABS 501 - Comb Wye and 1/8 Bend (All Hub)
1 1/2", 2", 3", 4"
ABS 502-Comb Wye & 1/8 Bend, Reducing One Pc.(Hub)
2" x 1 1/2" x 1 1/2"	2" x 1 1/2" x 2"	2" x 2" x 1 1/2"	3" x 3" x 1 1/2"
3" x 3" x 2"	4" x 4" x 2"	4" x 4" x 3"
ABS 600 - Wye (ALL HUB)
1 1/2", 2", 3", 4", 6"
ABS 601 - Wye, Reducing (All Hub)
2" x 1 1/2" x 1 1/2"	2" x 1 1/2" x 2"	2" x 2" x 1 1/2"	3" x 3" x 1 1/2"
3" x 3" x 2"	4" x 4" x 1 1/2"	4" x 4" x 2"	4" x 4" x 3"
6" x 6" x 4"
ABS 602 - Wye, Street (SPG x Hub x Hub)
1 1/2", 2", 3", 4"
ABS 603 - Wye, Street, Reducing (SPG x Hub x Hub)
3" x 3" x 1 1/2"	3" x 3" x 2"	4" x 4" x 3"
ABS 611 - Double Wye (All Hub)
1 1/2", 2", 3", 4"
ABS 612 - Double Wye, Reducing (All Hub)
2" x 2" x 1 1/2" x 1 1/2"	4" x 4" x 3" x 3"	3" x 3" x 2" x 2"	3" x 3" x 1 1/2" x 1 1/2"
ABS 700 - Return Bend (Hub x Hub)
1 1/2", 2", 3", 4"
ABS 704 - Tail Piece Adapter (SPG x Slip)
1 1/2"
ABS 704P-Tail Piece Adapter(SPGxSlip)w/Plastic Nut
1 1/2"
ABS 706x - P-Trap (Hub x Hub)
1 1/2", 2", 3", 4"
ABS 708P - P-Trap (Hub x Hub with Plastic Nut)
1 1/2", 2"
ABS 708x - P-Trap (Hub x Hub with Chrome Nut)
1 1/2"
ABS 710-DWV Low Profile P-Trap w/Solvent Weld Jnt
2"
ABS 711P - L.A. Pattern P-Trap (Slip x Hub)[3]
1 1/2"
ABS 711W-L.A. Pattern P-Trap Plstc Nut (SlipxHub
1 1/2"
ABS 800 - Closet Flange (Hub)
4" x 3"	4" x 4"
ABS 800Ko - Closet Flange with Knock Out (Hub)
4" x 3"
ABS 800S - Closet Flange with Stop (Hub)
4" x 3"
ABS 801 - Closet Flange, Reducing (SPG)
4" x 3"
ABS 808 - Closet Flange, Male (MPT)
4" x 3"
ABS 811-KO-Closet Flange, Adj w/Meta/Plasticl Ring
4" x 3"
ABS 811–Closet Flange, Adj Metal/Plstc Ring (Hub
4" x 3"	4" x 4"
ABS 811P - Closet Flange, Adj w/ABS Ring
4" x 3", 4" x 4"
ABS 812-Closet Flange, Adj
4" x 3"	4" x 4"
ABS 812P - Closet Flange, Adj Plastic Ring
4" x 3"
ABS 815 - Flush Closet Flange
4" x 4"/4" x 3"
ABS 815Ko - Flush Closet Flange with Knockout[2]
4" x 4"/4" x 3"
ABS 820-Offset Flange, Adj
4" x 3"
ABS 820P - Offset Flange, Adj Plastic Ring
4" x 3"
ABS 824-Closet Flange, Adjust. w/Metal Ring
4"
ABS 900-Swivel Tray Plug Adapter w/Washer(SPGxFPT)
1 1/2"
ABS 900x - ABS Ext Swivel Tray Adp
1 1/2"
ABS 910-Swivel Tray Plug Adapter w/Washer(SPGxFPT)
1 1/2"
[1] Plain End: Joint can be made with compression gasket only. [3] Furnished with 1 1/2 and 1 1/2 x 1 1/4 Polyethylene nut/washer combination. [2] Fits Over 3'' Pipe or Inside 4'' Pipe. @ A letter after the part number designates the following: X - Metal Ring/Plastic Ring R - Reducing P - Plastic Ring W - Washer ¢ Product is authorized to bear the cNSF and/or the cNSFus Mark. **** These fitting products may also be represented by the trade names: Charlotte Pipe and Foundry Company®, Charlotte Plastics®, Charlotte Pipe®, Charlotte®, Charlotte or Char®.
Fittings@	ABS	CPF®****	*SE 7992*
ABS 130 - Repair Coupling (Hub x Hub)
1 1/2", 2", 3", 4", 6"
ABS 720X - Drum Trap w/Cleanout
3" x 6" x 1 1/2"
@ A letter after the part number designates the following: X - Metal Ring/Plastic Ring R - Reducing P - Plastic Ring W - Washer **** These fitting products may also be represented by the trade names: Charlotte Pipe and Foundry Company®, Charlotte Plastics®, Charlotte Pipe®, Charlotte®, Charlotte or Char®.
Pipe~	ABS	Charlotte Pipe®***	CSA B181.1
1 1/4" - 6" Sch 40
~ Product is authorized to bear the cNSF Mark. *** These pipe products may include the production location code PLUT in the trade name.

Potable Water - Pipe and Fittings

Product Type	Material Type	Trade Name	Product Standard
Pipe + [G]*	PVC	Charlotte Pipe®***	CSA B137.3
1/8" - 18" Sch 40
1/8" - 18" Sch 80
* Sockets and gasketed bell ends are not tested or Listed by NSF for this production facility. + Material complies with NSF/ANSI/CAN 61 health effects requirements when tested at 73° F. *** These pipe products may include the production location code PLUT in the trade name. [G] Product is Certified to NSF/ANSI/CAN 372 and conforms with the lead content requirements for "lead free" plumbing as defined by California, Vermont, Maryland, and Louisiana state laws and the U.S. Safe Drinking Water Act.
Pipe + § [G]*	PVC	Charlotte Pipe®***	ASTM D1785
1/2" - 18" Sch 80
1/2" - 18" Sch 40
* Sockets and gasketed bell ends are not tested or Listed by NSF for this production facility. + Material complies with NSF/ANSI/CAN 61 health effects requirements when tested at 73° F. § Product is Certified to the Uniform Plumbing Code™. Installation in accordance with the manufacturer's instructions and the requirements of the latest edition of the Uniform Plumbing Code™. *** These pipe products may include the production location code PLUT in the trade name. [G] Product is Certified to NSF/ANSI/CAN 372 and conforms with the lead content requirements for "lead free" plumbing as defined by California, Vermont, Maryland, and Louisiana state laws and the U.S. Safe Drinking Water Act.
Pipe + § [G]*	PVC	Charlotte Pipe®***	ASTM D2241
1/2" SDR 13.5
3/4" - 2" SDR 21
1 1/4" - 2" SDR 26
2 1/2" - 12" SDR 32.5
4" - 12" SDR 41
* Sockets and gasketed bell ends are not tested or Listed by NSF for this production facility. + Material complies with NSF/ANSI/CAN 61 health effects requirements when tested at 73° F. § Product is Certified to the Uniform Plumbing Code™. Installation in accordance with the manufacturer's instructions and the requirements of the latest edition of the Uniform Plumbing Code™. *** These pipe products may include the production location code PLUT in the trade name. [G] Product is Certified to NSF/ANSI/CAN 372 and conforms with the lead content requirements for "lead free" plumbing as defined by California, Vermont, Maryland, and Louisiana state laws and the U.S. Safe Drinking Water Act.

Well Casings

Product Type	Material Type	Trade Name	Product Standard
Well Casings[G]	PVC	Charlotte Pipe®***	ASTM F480
2" - 14", 16" Sch 40
6" - 14", 16" SDR 21
*** These pipe products may include the production location code PLUT in the trade name. [G] Product is Certified to NSF/ANSI/CAN 372 and conforms with the lead content requirements for "lead free" plumbing as defined by California, Vermont, Maryland, and Louisiana state laws and the U.S. Safe Drinking Water Act.

Number of matching Manufacturers is 1
Number of matching Products is 3174
Processing time was 1 seconds

Product Type

Material Type

Trade Name

Product Standard

Well Casings§ [G]

Charlotte Pipe®***

ASTM F480

2" - 8" Sch 40

4", 6" SDR 21

4", 6" SDR 26

§ Product is Certified to the Uniform Plumbing Code™. Installation in accordance with the manufacturer's instructions and the requirements of the latest edition of the Uniform Plumbing Code™. *** These pipe products may include the production location code PLFL in the trade name. [G] Product is Certified to NSF/ANSI/CAN 372 and conforms with the lead content requirements for "lead free" plumbing as defined by California, Vermont, Maryland, and Louisiana state laws and the U.S. Safe Drinking Water Act.