% PEX pipe and fittings are intended for use in multi-purpose piping systems of
  residential occupancies as
  defined in ANSI/NFPA 13D, “Installation of Sprinkler Systems in One- and Two- Family
  Dwellings and
  Manufactured Homes"" and the International Residential Code, Section P2904, and are
  designed to
  withstand a working pressure of not less than 130 psi at 120°F. PEX pipe and fittings
  are intended to be
  installed in accordance with the requirements specified in the manufacturer’s
  installation instructions
  and ANSI/NFPA 13D. Protection is intended to be provided for PEX pipe and fittings in
  multi-purpose
  piping systems unless otherwise stated in this listing and per the installation and
  design manual dated
  September 11, 2008. The minimum protection should consist of either (1) one layer of
  3/8-in. gypsum
  wallboard, (2) a suspended membrane ceiling with lay-in panels or tiles having a weight
  of not less than
  0.35 lbs per sq ft when installed with metallic support grids, OR (3) ½ in plywood. PEX
  pipe and
  fittings are intended for use in areas where the maximum ambient temperature does not
  exceed 120°F.
  These pipe and fittings are not intended to be installed in outdoor applications. The
  PEX pipe and
  fittings are intended for use in wet-pipe systems only and have not been evaluated for
  use in dry-pipe
  systems. Raupex pipe and fittings may also be installed without protection (exposed) in
  accordance with
  the limitations specified in this installation and design manual dated September 11,
  2008.
** Pipe and fittings Certified as a system using installation and design manual titled
   "FIREPEX Residential
   Fire Sprinkler
[G] Product is Certified to NSF/ANSI/CAN 372 and conforms with the lead content requirements
    for "lead free" plumbing as defined by California, Vermont, Maryland, and Louisiana
    state laws and the U.S. Safe Drinking Water Act.

§ Product is Certified to the Uniform Plumbing Code™. Installation in accordance with the
  manufacturer's instructions and the requirements of the latest edition of the Uniform
  Plumbing Code™.
+++ Material complies with NSF/ANSI/CAN 61 health effects requirements when tested at
    temperatures up to and including Commercial Hot (180° F).
[G] Product is Certified to NSF/ANSI/CAN 372 and conforms with the lead content requirements
    for "lead free" plumbing as defined by California, Vermont, Maryland, and Louisiana
    state laws and the U.S. Safe Drinking Water Act.

¢ Product is authorized to bear the cNSF and/or the cNSFus Mark.
§ Product is Certified to the Uniform Plumbing Code™. Installation in accordance with the
  manufacturer's instructions and the requirements of the latest edition of the Uniform
  Plumbing Code™.
+++ Material complies with NSF/ANSI/CAN 61 health effects requirements when tested at
    temperatures up to and including Commercial Hot (180° F).
[G] Product is Certified to NSF/ANSI/CAN 372 and conforms with the lead content requirements
    for "lead free" plumbing as defined by California, Vermont, Maryland, and Louisiana
    state laws and the U.S. Safe Drinking Water Act.

§ Product is Certified to the Uniform Plumbing Code™. Installation in accordance with the
  manufacturer's instructions and the requirements of the latest edition of the Uniform
  Plumbing Code™.
+++ Material complies with NSF/ANSI/CAN 61 health effects requirements when tested at
    temperatures up to and including Commercial Hot (180° F).
[G] Product is Certified to NSF/ANSI/CAN 372 and conforms with the lead content requirements
    for "lead free" plumbing as defined by California, Vermont, Maryland, and Louisiana
    state laws and the U.S. Safe Drinking Water Act.

¢ Product is authorized to bear the cNSF and/or the cNSFus Mark.
§ Product is Certified to the Uniform Plumbing Code™. Installation in accordance with the
  manufacturer's instructions and the requirements of the latest edition of the Uniform
  Plumbing Code™.
+++ Material complies with NSF/ANSI/CAN 61 health effects requirements when tested at
    temperatures up to and including Commercial Hot (180° F).
[G] Product is Certified to NSF/ANSI/CAN 372 and conforms with the lead content requirements
    for "lead free" plumbing as defined by California, Vermont, Maryland, and Louisiana
    state laws and the U.S. Safe Drinking Water Act.

¢ Product is authorized to bear the cNSF and/or the cNSFus Mark.

¢ Product is authorized to bear the cNSF and/or the cNSFus Mark.

¢ Product is authorized to bear the cNSF and/or the cNSFus Mark.

[3] Flame Spread Value (FSV) <= 25; Smoke Developed Value (SDV) <= 50.
[4] Flame Spread Index and Smoke Developed Index based on when tubing is field insulated
    with 1/2" Micro-lok HP Hi performance fiberglass insulation with Everloc+P/Everloc+
    Fittings as per Rehau installation instructions. 
    Tubing shall be marked [cNSF®-fs CAN/ULC S102.2 FS<=25/SD<=50].

[3] Flame Spread Value (FSV) <= 25; Smoke Developed Value (SDV) <= 50.
[4] Flame Spread Index and Smoke Developed Index based on when tubing is field insulated
    with 1/2" Micro-lok HP Hi performance fiberglass insulation with Everloc+P/Everloc+
    Fittings as per Rehau installation instructions. 
    Tubing shall be marked [cNSF®-fs CAN/ULC S102.2 FS<=25/SD<=50].

* Flame Spread Index and Smoke Developed Index based on when tubing is field insulated
  with minimum 1/2" Microlok HP Hi performance fiberglass insulation as per Rehau
  installation instructions.
[1] Flame Spread Index <= 25; Smoke Developed Index <= 50.

*** Flame Spread Index and Smoke Developed Index based on ASTM E84 Steiner tunnel modified
    using piping supported with a minimum length of 48-inch Rehau pipe supports spaced a   
    maximum distance of 10-inches between each Rehau Pipe Support Run. Tubing shall be
    marked [NSF®-fs ASTM E84 FS<=25/SD<=50].
    
    
    
    
[1] Flame Spread Index <= 25; Smoke Developed Index <= 50.

[2] Flame Spread Index and Smoke Developed Index based on when tubing is field insulated
    with minimum 1/2" JM Microlok or Armaflex insulation as per Rehau installation
    instructions.
[3] Flame Spread Value (FSV) <= 25; Smoke Developed Value (SDV) <= 50.

* Flame Spread Index and Smoke Developed Index based on when tubing is field insulated
  with minimum 1/2" Microlok HP Hi performance fiberglass insulation as per Rehau
  installation instructions.
[1] Flame Spread Index <= 25; Smoke Developed Index <= 50.

** Flame Spread Index and Smoke Developed Index based on minimum spacing of 18 inches
   between tubing runs with Everloc+P, Everloc+ fittings.  Tubing shall be marked [NSF®-fs
   ASTM E84 FS<=25/SD<=50].
   
   
[1] Flame Spread Index <= 25; Smoke Developed Index <= 50.

[3] Flame Spread Value (FSV) <= 25; Smoke Developed Value (SDV) <= 50.

[2] Flame Spread Index and Smoke Developed Index based on when tubing is field insulated
    with minimum 1/2" JM Microlok or Armaflex insulation as per Rehau installation
    instructions.
[3] Flame Spread Value (FSV) <= 25; Smoke Developed Value (SDV) <= 50.

* Flame Spread Index and Smoke Developed Index based on when tubing is field insulated
  with minimum 1/2" Microlok HP Hi performance fiberglass insulation as per Rehau
  installation instructions.
[1] Flame Spread Index <= 25; Smoke Developed Index <= 50.

** Flame Spread Index and Smoke Developed Index based on minimum spacing of 18 inches
   between tubing runs with Everloc+P, Everloc+ fittings.  Tubing shall be marked [NSF®-fs
   ASTM E84 FS<=25/SD<=50].
   
   
[1] Flame Spread Index <= 25; Smoke Developed Index <= 50.

*** Flame Spread Index and Smoke Developed Index based on ASTM E84 Steiner tunnel modified
    using piping supported with a minimum length of 48-inch Rehau pipe supports spaced a   
    maximum distance of 10-inches between each Rehau Pipe Support Run. Tubing shall be
    marked [NSF®-fs ASTM E84 FS<=25/SD<=50].
    
    
    
    
[1] Flame Spread Index <= 25; Smoke Developed Index <= 50.

[3] Flame Spread Value (FSV) <= 25; Smoke Developed Value (SDV) <= 50.

[2] Flame Spread Index and Smoke Developed Index based on when tubing is field insulated
    with minimum 1/2" JM Microlok or Armaflex insulation as per Rehau installation
    instructions.
[3] Flame Spread Value (FSV) <= 25; Smoke Developed Value (SDV) <= 50.

* Flame Spread Index and Smoke Developed Index based on when tubing is field insulated
  with minimum 1/2" Microlok HP Hi performance fiberglass insulation as per Rehau
  installation instructions.
[1] Flame Spread Index <= 25; Smoke Developed Index <= 50.

** Flame Spread Index and Smoke Developed Index based on minimum spacing of 18 inches
   between tubing runs with Everloc+P, Everloc+ fittings.  Tubing shall be marked [NSF®-fs
   ASTM E84 FS<=25/SD<=50].
   
   
[1] Flame Spread Index <= 25; Smoke Developed Index <= 50.

*** Flame Spread Index and Smoke Developed Index based on ASTM E84 Steiner tunnel modified
    using piping supported with a minimum length of 48-inch Rehau pipe supports spaced a   
    maximum distance of 10-inches between each Rehau Pipe Support Run. Tubing shall be
    marked [NSF®-fs ASTM E84 FS<=25/SD<=50].
    
    
    
    
[1] Flame Spread Index <= 25; Smoke Developed Index <= 50.

[1] Flame Spread Index <= 25; Smoke Developed Index <= 50.
***** Flame Spread Index and Smoke Developed Index based on when tubing is field insulated
      with minimum 1/2" Micro-lok HP Hi performance fiberglass insulation with
      Everloc+P/Everloc+ Fittings as per Rehau installation instructions. Tubing shall be
      marked [NSF®-fs ASTM E84 FS<=25/SD<=50].

[3] Flame Spread Value (FSV) <= 25; Smoke Developed Value (SDV) <= 50.

[2] Flame Spread Index and Smoke Developed Index based on when tubing is field insulated
    with minimum 1/2" JM Microlok or Armaflex insulation as per Rehau installation
    instructions.
[3] Flame Spread Value (FSV) <= 25; Smoke Developed Value (SDV) <= 50.

* Flame Spread Index and Smoke Developed Index based on when tubing is field insulated
  with minimum 1/2" Microlok HP Hi performance fiberglass insulation as per Rehau
  installation instructions.
[1] Flame Spread Index <= 25; Smoke Developed Index <= 50.

[3] Flame Spread Value (FSV) <= 25; Smoke Developed Value (SDV) <= 50.
[4] Flame Spread Index and Smoke Developed Index based on when tubing is field insulated
    with 1/2" Micro-lok HP Hi performance fiberglass insulation with Everloc+P/Everloc+
    Fittings as per Rehau installation instructions. 
    Tubing shall be marked [cNSF®-fs CAN/ULC S102.2 FS<=25/SD<=50].

** Flame Spread Index and Smoke Developed Index based on minimum spacing of 18 inches
   between tubing runs with Everloc+P, Everloc+ fittings.  Tubing shall be marked [NSF®-fs
   ASTM E84 FS<=25/SD<=50].
   
   
[1] Flame Spread Index <= 25; Smoke Developed Index <= 50.

*** Flame Spread Index and Smoke Developed Index based on ASTM E84 Steiner tunnel modified
    using piping supported with a minimum length of 48-inch Rehau pipe supports spaced a   
    maximum distance of 10-inches between each Rehau Pipe Support Run. Tubing shall be
    marked [NSF®-fs ASTM E84 FS<=25/SD<=50].
    
    
    
    
[1] Flame Spread Index <= 25; Smoke Developed Index <= 50.

[1] Flame Spread Index <= 25; Smoke Developed Index <= 50.
***** Flame Spread Index and Smoke Developed Index based on when tubing is field insulated
      with minimum 1/2" Micro-lok HP Hi performance fiberglass insulation with
      Everloc+P/Everloc+ Fittings as per Rehau installation instructions. Tubing shall be
      marked [NSF®-fs ASTM E84 FS<=25/SD<=50].

[3] Flame Spread Value (FSV) <= 25; Smoke Developed Value (SDV) <= 50.

[2] Flame Spread Index and Smoke Developed Index based on when tubing is field insulated
    with minimum 1/2" JM Microlok or Armaflex insulation as per Rehau installation
    instructions.
[3] Flame Spread Value (FSV) <= 25; Smoke Developed Value (SDV) <= 50.

* Flame Spread Index and Smoke Developed Index based on when tubing is field insulated
  with minimum 1/2" Microlok HP Hi performance fiberglass insulation as per Rehau
  installation instructions.
[1] Flame Spread Index <= 25; Smoke Developed Index <= 50.

** Flame Spread Index and Smoke Developed Index based on minimum spacing of 18 inches
   between tubing runs with Everloc+P, Everloc+ fittings.  Tubing shall be marked [NSF®-fs
   ASTM E84 FS<=25/SD<=50].
   
   
[1] Flame Spread Index <= 25; Smoke Developed Index <= 50.

*** Flame Spread Index and Smoke Developed Index based on ASTM E84 Steiner tunnel modified
    using piping supported with a minimum length of 48-inch Rehau pipe supports spaced a   
    maximum distance of 10-inches between each Rehau Pipe Support Run. Tubing shall be
    marked [NSF®-fs ASTM E84 FS<=25/SD<=50].
    
    
    
    
[1] Flame Spread Index <= 25; Smoke Developed Index <= 50.

[1] Flame Spread Index <= 25; Smoke Developed Index <= 50.
***** Flame Spread Index and Smoke Developed Index based on when tubing is field insulated
      with minimum 1/2" Micro-lok HP Hi performance fiberglass insulation with
      Everloc+P/Everloc+ Fittings as per Rehau installation instructions. Tubing shall be
      marked [NSF®-fs ASTM E84 FS<=25/SD<=50].

[3] Flame Spread Value (FSV) <= 25; Smoke Developed Value (SDV) <= 50.

[2] Flame Spread Index and Smoke Developed Index based on when tubing is field insulated
    with minimum 1/2" JM Microlok or Armaflex insulation as per Rehau installation
    instructions.
[3] Flame Spread Value (FSV) <= 25; Smoke Developed Value (SDV) <= 50.

[2] Flame Spread Index and Smoke Developed Index based on when tubing is field insulated
    with minimum 1/2" JM Microlok or Armaflex insulation as per Rehau installation
    instructions.
[3] Flame Spread Value (FSV) <= 25; Smoke Developed Value (SDV) <= 50.

* Accepted by NSF for use in residential and commercial construction,
  including manufactured housing.
^ Meets the chlorine resistance requirements of ASTM F876 when tested in accordance with
  ASTM F2023.
+++ Material complies with NSF/ANSI/CAN 61 health effects requirements when tested at
    temperatures up to and including Commercial Hot (180° F).
[G] Product is Certified to NSF/ANSI/CAN 372 and conforms with the lead content requirements
    for "lead free" plumbing as defined by California, Vermont, Maryland, and Louisiana
    state laws and the U.S. Safe Drinking Water Act.

* Accepted by NSF for use in residential and commercial construction,
  including manufactured housing.
^ Meets the chlorine resistance requirements of ASTM F876 when tested in accordance with
  ASTM F2023.
+++ Material complies with NSF/ANSI/CAN 61 health effects requirements when tested at
    temperatures up to and including Commercial Hot (180° F).
[G] Product is Certified to NSF/ANSI/CAN 372 and conforms with the lead content requirements
    for "lead free" plumbing as defined by California, Vermont, Maryland, and Louisiana
    state laws and the U.S. Safe Drinking Water Act.

& Tubing certified against CSA B137.5 shall include the standard designation(s) of the
  fitting system(s) for which the tubing is recommended by the manufacturer, and shall be
  marked, as applicable, with the following fitting system designation(s): AWWA C800.
* Accepted by NSF for use in residential and commercial construction,
  including manufactured housing.
^ Meets the chlorine resistance requirements of ASTM F876 when tested in accordance with
  ASTM F2023.
¢ Product is authorized to bear the cNSF and/or the cNSFus Mark.
§ Product is Certified to the Uniform Plumbing Code™. Installation in accordance with the
  manufacturer's instructions and the requirements of the latest edition of the Uniform
  Plumbing Code™.
+++ Material complies with NSF/ANSI/CAN 61 health effects requirements when tested at
    temperatures up to and including Commercial Hot (180° F).
[G] Product is Certified to NSF/ANSI/CAN 372 and conforms with the lead content requirements
    for "lead free" plumbing as defined by California, Vermont, Maryland, and Louisiana
    state laws and the U.S. Safe Drinking Water Act.

* Accepted by NSF for use in residential and commercial construction,
  including manufactured housing.
^ Meets the chlorine resistance requirements of ASTM F876 when tested in accordance with
  ASTM F2023.
§ Product is Certified to the Uniform Plumbing Code™. Installation in accordance with the
  manufacturer's instructions and the requirements of the latest edition of the Uniform
  Plumbing Code™.
$$ Complies with US EPA Maximum Contaminant Levels (MCLs) for PFAS according to
   NSF/ANSI/CAN 61.
+++ Material complies with NSF/ANSI/CAN 61 health effects requirements when tested at
    temperatures up to and including Commercial Hot (180° F).
[G] Product is Certified to NSF/ANSI/CAN 372 and conforms with the lead content requirements
    for "lead free" plumbing as defined by California, Vermont, Maryland, and Louisiana
    state laws and the U.S. Safe Drinking Water Act.

% Tubing certified against CSA B137.5 shall include the standard designation(s) of the
  fitting system(s) for which the tubing is recommended by the manufacturer, and shall be
  marked, as applicable, with the following fitting system designation(s):  ASTM F877,
  F1807, F1960, F2080 and F2159.
* Accepted by NSF for use in residential and commercial construction,
  including manufactured housing.
^ Meets the chlorine resistance requirements of ASTM F876 when tested in accordance with
  ASTM F2023.
¢ Product is authorized to bear the cNSF and/or the cNSFus Mark.
§ Product is Certified to the Uniform Plumbing Code™. Installation in accordance with the
  manufacturer's instructions and the requirements of the latest edition of the Uniform
  Plumbing Code™.
$$ Complies with US EPA Maximum Contaminant Levels (MCLs) for PFAS according to
   NSF/ANSI/CAN 61.
+++ Material complies with NSF/ANSI/CAN 61 health effects requirements when tested at
    temperatures up to and including Commercial Hot (180° F).
[G] Product is Certified to NSF/ANSI/CAN 372 and conforms with the lead content requirements
    for "lead free" plumbing as defined by California, Vermont, Maryland, and Louisiana
    state laws and the U.S. Safe Drinking Water Act.

* Accepted by NSF for use in residential and commercial construction,
  including manufactured housing.
^ Meets the chlorine resistance requirements of ASTM F876 when tested in accordance with
  ASTM F2023.
§ Product is Certified to the Uniform Plumbing Code™. Installation in accordance with the
  manufacturer's instructions and the requirements of the latest edition of the Uniform
  Plumbing Code™.
$$ Complies with US EPA Maximum Contaminant Levels (MCLs) for PFAS according to
   NSF/ANSI/CAN 61.
+++ Material complies with NSF/ANSI/CAN 61 health effects requirements when tested at
    temperatures up to and including Commercial Hot (180° F).
[G] Product is Certified to NSF/ANSI/CAN 372 and conforms with the lead content requirements
    for "lead free" plumbing as defined by California, Vermont, Maryland, and Louisiana
    state laws and the U.S. Safe Drinking Water Act.

% Tubing certified against CSA B137.5 shall include the standard designation(s) of the
  fitting system(s) for which the tubing is recommended by the manufacturer, and shall be
  marked, as applicable, with the following fitting system designation(s):  ASTM F877,
  F1807, F1960, F2080 and F2159.
* Accepted by NSF for use in residential and commercial construction,
  including manufactured housing.
^ Meets the chlorine resistance requirements of ASTM F876 when tested in accordance with
  ASTM F2023.
¢ Product is authorized to bear the cNSF and/or the cNSFus Mark.
§ Product is Certified to the Uniform Plumbing Code™. Installation in accordance with the
  manufacturer's instructions and the requirements of the latest edition of the Uniform
  Plumbing Code™.
$$ Complies with US EPA Maximum Contaminant Levels (MCLs) for PFAS according to
   NSF/ANSI/CAN 61.
+++ Material complies with NSF/ANSI/CAN 61 health effects requirements when tested at
    temperatures up to and including Commercial Hot (180° F).
[G] Product is Certified to NSF/ANSI/CAN 372 and conforms with the lead content requirements
    for "lead free" plumbing as defined by California, Vermont, Maryland, and Louisiana
    state laws and the U.S. Safe Drinking Water Act.

* Accepted by NSF for use in residential and commercial construction,
  including manufactured housing.
^ Meets the chlorine resistance requirements of ASTM F876 when tested in accordance with
  ASTM F2023.
§ Product is Certified to the Uniform Plumbing Code™. Installation in accordance with the
  manufacturer's instructions and the requirements of the latest edition of the Uniform
  Plumbing Code™.
$$ Complies with US EPA Maximum Contaminant Levels (MCLs) for PFAS according to
   NSF/ANSI/CAN 61.
+++ Material complies with NSF/ANSI/CAN 61 health effects requirements when tested at
    temperatures up to and including Commercial Hot (180° F).
[G] Product is Certified to NSF/ANSI/CAN 372 and conforms with the lead content requirements
    for "lead free" plumbing as defined by California, Vermont, Maryland, and Louisiana
    state laws and the U.S. Safe Drinking Water Act.

% Tubing certified against CSA B137.5 shall include the standard designation(s) of the
  fitting system(s) for which the tubing is recommended by the manufacturer, and shall be
  marked, as applicable, with the following fitting system designation(s):  ASTM F877,
  F1807, F1960, F2080 and F2159.
* Accepted by NSF for use in residential and commercial construction,
  including manufactured housing.
^ Meets the chlorine resistance requirements of ASTM F876 when tested in accordance with
  ASTM F2023.
¢ Product is authorized to bear the cNSF and/or the cNSFus Mark.
§ Product is Certified to the Uniform Plumbing Code™. Installation in accordance with the
  manufacturer's instructions and the requirements of the latest edition of the Uniform
  Plumbing Code™.
$$ Complies with US EPA Maximum Contaminant Levels (MCLs) for PFAS according to
   NSF/ANSI/CAN 61.
+++ Material complies with NSF/ANSI/CAN 61 health effects requirements when tested at
    temperatures up to and including Commercial Hot (180° F).
[G] Product is Certified to NSF/ANSI/CAN 372 and conforms with the lead content requirements
    for "lead free" plumbing as defined by California, Vermont, Maryland, and Louisiana
    state laws and the U.S. Safe Drinking Water Act.

¢ Product is authorized to bear the cNSF and/or the cNSFus Mark.
§ Product is Certified to the Uniform Plumbing Code™. Installation in accordance with the
  manufacturer's instructions and the requirements of the latest edition of the Uniform
  Plumbing Code™.
+++ Material complies with NSF/ANSI/CAN 61 health effects requirements when tested at
    temperatures up to and including Commercial Hot (180° F).

¢ Product is authorized to bear the cNSF and/or the cNSFus Mark.
§ Product is Certified to the Uniform Plumbing Code™. Installation in accordance with the
  manufacturer's instructions and the requirements of the latest edition of the Uniform
  Plumbing Code™.
+++ Material complies with NSF/ANSI/CAN 61 health effects requirements when tested at
    temperatures up to and including Commercial Hot (180° F).

$ Non-barrier pipe.
* Accepted by NSF for use in residential and commercial construction, including
  manufactured housing.
^ Meets the chlorine resistance requirements of ASTM F876 when tested in accordance with 
  ASTM F2023.
§ Product is Certified to the Uniform Plumbing Code™. Installation in accordance with the
  manufacturer's instructions and the requirements of the latest edition of the Uniform
  Plumbing Code™.

$ Non-barrier pipe.
% Tubing certified against CSA B137.5 shall include the standard designation(s) of the
  fitting system(s) for which the tubing is recommended by the manufacturer, and shall be
  marked, as applicable, with the following fitting system designation(s):  ASTM F877,
  F1807, F1960, F2080 and F2159.
* Accepted by NSF for use in residential and commercial construction, including
  manufactured housing.
§ Product is Certified to the Uniform Plumbing Code™. Installation in accordance with the
  manufacturer's instructions and the requirements of the latest edition of the Uniform
  Plumbing Code™.

* Accepted by NSF for use in residential and commercial construction, including
  manufactured housing.
¥ Product is Certified to the Uniform Mechanical Code™. Installation in accordance with
  the manufacturer's instructions and the requirements of the latest edition of the
  Uniform Mechanical Code™.

% Tubing certified against CSA B137.5 shall include the standard designation(s) of the
  fitting system(s) for which the tubing is recommended by the manufacturer, and shall be
  marked, as applicable, with the following fitting system designation(s):  ASTM F877,
  F1807, F1960, F2080 and F2159.
* Accepted by NSF for use in residential and commercial construction, including
  manufactured housing.
¢ Product is authorized to bear the cNSF and/or the cNSFus Mark.
¥ Product is Certified to the Uniform Mechanical Code™. Installation in accordance with
  the manufacturer's instructions and the requirements of the latest edition of the
  Uniform Mechanical Code™.

¢ Product is authorized to bear the cNSF and/or the cNSFus Mark.
§ Product is Certified to the Uniform Plumbing Code™. Installation in accordance with the
  manufacturer's instructions and the requirements of the latest edition of the Uniform
  Plumbing Code™.
+++ Material complies with NSF/ANSI/CAN 61 health effects requirements when tested at
    temperatures up to and including Commercial Hot (180° F).
[G] Product is Certified to NSF/ANSI/CAN 372 and conforms with the lead content requirements
    for "lead free" plumbing as defined by California, Vermont, Maryland, and Louisiana
    state laws and the U.S. Safe Drinking Water Act.

¢ Product is authorized to bear the cNSF and/or the cNSFus Mark.
§ Product is Certified to the Uniform Plumbing Code™. Installation in accordance with the
  manufacturer's instructions and the requirements of the latest edition of the Uniform
  Plumbing Code™.
+++ Material complies with NSF/ANSI/CAN 61 health effects requirements when tested at
    temperatures up to and including Commercial Hot (180° F).
[G] Product is Certified to NSF/ANSI/CAN 372 and conforms with the lead content requirements
    for "lead free" plumbing as defined by California, Vermont, Maryland, and Louisiana
    state laws and the U.S. Safe Drinking Water Act.

¢ Product is authorized to bear the cNSF and/or the cNSFus Mark.
§ Product is Certified to the Uniform Plumbing Code™. Installation in accordance with the
  manufacturer's instructions and the requirements of the latest edition of the Uniform
  Plumbing Code™.
+++ Material complies with NSF/ANSI/CAN 61 health effects requirements when tested at
    temperatures up to and including Commercial Hot (180° F).
[G] Product is Certified to NSF/ANSI/CAN 372 and conforms with the lead content requirements
    for "lead free" plumbing as defined by California, Vermont, Maryland, and Louisiana
    state laws and the U.S. Safe Drinking Water Act.

¢ Product is authorized to bear the cNSF and/or the cNSFus Mark.
§ Product is Certified to the Uniform Plumbing Code™. Installation in accordance with the
  manufacturer's instructions and the requirements of the latest edition of the Uniform
  Plumbing Code™.
+++ Material complies with NSF/ANSI/CAN 61 health effects requirements when tested at
    temperatures up to and including Commercial Hot (180° F).
[G] Product is Certified to NSF/ANSI/CAN 372 and conforms with the lead content requirements
    for "lead free" plumbing as defined by California, Vermont, Maryland, and Louisiana
    state laws and the U.S. Safe Drinking Water Act.

% PEX pipe and fittings are intended for use in multi-purpose piping systems of
  residential occupancies as defined in ANSI/NFPA 13D, “Installation of Sprinkler Systems
  in One- and Two- Family Dwellings and Manufactured Homes"" and the International
  Residential Code, Section P2904, and are designed to withstand a working pressure of not
  less than 130 psi at 120°F. PEX pipe and fittings are intended to be installed in
  accordance with the requirements specified in the manufacturer’s installation
  instructions and ANSI/NFPA 13D. Protection is intended to be provided for PEX pipe and
  fittings in multi-purpose piping systems unless otherwise stated in this listing and per
  the installation and design manual dated September 11, 2008. The minimum protection
  should consist of either (1) one layer of 3/8-in. gypsum wallboard, (2) a suspended
  membrane ceiling with lay-in panels or tiles having a weight of not less than 0.35 lbs
  per sq ft when installed with metallic support grids, OR (3) ½ in plywood. PEX pipe and
  fittings are intended for use in areas where the maximum ambient temperature does not
  exceed 120°F. These pipe and fittings are not intended to be installed in outdoor
  applications. The PEX pipe and fittings are intended for use in wet-pipe systems only
  and have not been evaluated for use in dry-pipe systems. Raupex pipe and fittings may
  also be installed without protection (exposed) in accordance with the limitations
  specified in this installation and design manual dated September 11, 2008.
** Pipe and fittings Certified as a system using installation and design manual titled
   "FIREPEX Residential
   Fire Sprinkler Systems".
[G] Product is Certified to NSF/ANSI/CAN 372 and conforms with the lead content requirements
    for "lead free" plumbing as defined by California, Vermont, Maryland, and Louisiana
    state laws and the U.S. Safe Drinking Water Act.

§ Product is Certified to the Uniform Plumbing Code™. Installation in accordance with the
  manufacturer's instructions and the requirements of the latest edition of the Uniform
  Plumbing Code™.
+++ Material complies with NSF/ANSI/CAN 61 health effects requirements when tested at
    temperatures up to and including Commercial Hot (180° F).
[G] Product is Certified to NSF/ANSI/CAN 372 and conforms with the lead content requirements
    for "lead free" plumbing as defined by California, Vermont, Maryland, and Louisiana
    state laws and the U.S. Safe Drinking Water Act.

§ Product is Certified to the Uniform Plumbing Code™. Installation in accordance with the
  manufacturer's instructions and the requirements of the latest edition of the Uniform
  Plumbing Code™.
+++ Material complies with NSF/ANSI/CAN 61 health effects requirements when tested at
    temperatures up to and including Commercial Hot (180° F).
[G] Product is Certified to NSF/ANSI/CAN 372 and conforms with the lead content requirements
    for "lead free" plumbing as defined by California, Vermont, Maryland, and Louisiana
    state laws and the U.S. Safe Drinking Water Act.

§ Product is Certified to the Uniform Plumbing Code™. Installation in accordance with the
  manufacturer's instructions and the requirements of the latest edition of the Uniform
  Plumbing Code™.
+++ Material complies with NSF/ANSI/CAN 61 health effects requirements when tested at
    temperatures up to and including Commercial Hot (180° F).
[G] Product is Certified to NSF/ANSI/CAN 372 and conforms with the lead content requirements
    for "lead free" plumbing as defined by California, Vermont, Maryland, and Louisiana
    state laws and the U.S. Safe Drinking Water Act.

§ Product is Certified to the Uniform Plumbing Code™. Installation in accordance with the
  manufacturer's instructions and the requirements of the latest edition of the Uniform
  Plumbing Code™.
+++ Material complies with NSF/ANSI/CAN 61 health effects requirements when tested at
    temperatures up to and including Commercial Hot (180° F).
[G] Product is Certified to NSF/ANSI/CAN 372 and conforms with the lead content requirements
    for "lead free" plumbing as defined by California, Vermont, Maryland, and Louisiana
    state laws and the U.S. Safe Drinking Water Act.

¢ Product is authorized to bear the cNSF and/or the cNSFus Mark.

¢ Product is authorized to bear the cNSF and/or the cNSFus Mark.

[1] Nickel Plated Manifold Outlet 

¢ Product is authorized to bear the cNSF and/or the cNSFus Mark.
[1] Nickel Plated Manifold Outlet 

§ Product is Certified to the Uniform Plumbing Code™. Installation in accordance with the
  manufacturer's instructions and the requirements of the latest edition of the Uniform
  Plumbing Code™.
+++ Material complies with NSF/ANSI/CAN 61 health effects requirements when tested at
    temperatures up to and including Commercial Hot (180° F).
[G] Product is Certified to NSF/ANSI/CAN 372 and conforms with the lead content requirements
    for "lead free" plumbing as defined by California, Vermont, Maryland, and Louisiana
    state laws and the U.S. Safe Drinking Water Act.

§ Product is Certified to the Uniform Plumbing Code™. Installation in accordance with the
  manufacturer's instructions and the requirements of the latest edition of the Uniform
  Plumbing Code™.
+++ Material complies with NSF/ANSI/CAN 61 health effects requirements when tested at
    temperatures up to and including Commercial Hot (180° F).
[G] Product is Certified to NSF/ANSI/CAN 372 and conforms with the lead content requirements
    for "lead free" plumbing as defined by California, Vermont, Maryland, and Louisiana
    state laws and the U.S. Safe Drinking Water Act.

* Flame Spread Index and Smoke Developed Index based on when tubing is field insulated
  with minimum 1/2" Microlok HP Hi performance fiberglass insulation as per Rehau
  installation instructions.
[1] Flame Spread Index <= 25; Smoke Developed Index <= 50.

*** Flame Spread Index and Smoke Developed Index based on ASTM E84 Steiner tunnel modified
    using piping supported with a minimum length of 48-inch Rehau pipe supports spaced a
    maximum distance of 10-inches between each Rehau Pipe Support Run. Tubing shall be
    marked [NSF®-fs ASTM E84 FS<=25/SD<=50].
    
[1] Flame Spread Index <= 25; Smoke Developed Index <= 50.

[2] Flame Spread Index and Smoke Developed Index based on when tubing is field insulated
    with minimum 1/2" JM Microlok or Armaflex insulation as per Rehau installation
    instructions.
[3] Flame Spread Value (FSV) <= 25; Smoke Developed Value (SDV) <= 50.

* Flame Spread Index and Smoke Developed Index based on when tubing is field insulated
  with minimum 1/2" Microlok HP Hi performance fiberglass insulation as per Rehau
  installation instructions.
[1] Flame Spread Index <= 25; Smoke Developed Index <= 50.

*** Flame Spread Index and Smoke Developed Index based on ASTM E84 Steiner tunnel modified
    using piping supported with a minimum length of 48-inch Rehau pipe supports spaced a
    maximum distance of 10-inches between each Rehau Pipe Support Run. Tubing shall be
    marked [NSF®-fs ASTM E84 FS<=25/SD<=50].
    
[1] Flame Spread Index <= 25; Smoke Developed Index <= 50.

[2] Flame Spread Index and Smoke Developed Index based on when tubing is field insulated
    with minimum 1/2" JM Microlok or Armaflex insulation as per Rehau installation
    instructions.
[3] Flame Spread Value (FSV) <= 25; Smoke Developed Value (SDV) <= 50.

** Flame Spread Index and Smoke Developed Index based on minimum spacing of 18 inches
   between tubing runs with Everloc+P, Everloc+ fittings.  Tubing shall be marked [NSF®-fs
   ASTM E84 FS<=25/SD<=50].
[1] Flame Spread Index <= 25; Smoke Developed Index <= 50.

* Flame Spread Index and Smoke Developed Index based on when tubing is field insulated
  with minimum 1/2" Microlok HP Hi performance fiberglass insulation as per Rehau
  installation instructions.
[1] Flame Spread Index <= 25; Smoke Developed Index <= 50.

[3] Flame Spread Value (FSV) <= 25; Smoke Developed Value (SDV) <= 50.

[2] Flame Spread Index and Smoke Developed Index based on when tubing is field insulated
    with minimum 1/2" JM Microlok or Armaflex insulation as per Rehau installation
    instructions.
[3] Flame Spread Value (FSV) <= 25; Smoke Developed Value (SDV) <= 50.

** Flame Spread Index and Smoke Developed Index based on minimum spacing of 18 inches
   between tubing runs with Everloc+P, Everloc+ fittings.  Tubing shall be marked [NSF®-fs
   ASTM E84 FS<=25/SD<=50].
[1] Flame Spread Index <= 25; Smoke Developed Index <= 50.

* Flame Spread Index and Smoke Developed Index based on when tubing is field insulated
  with minimum 1/2" Microlok HP Hi performance fiberglass insulation as per Rehau
  installation instructions.
[1] Flame Spread Index <= 25; Smoke Developed Index <= 50.

*** Flame Spread Index and Smoke Developed Index based on ASTM E84 Steiner tunnel modified
    using piping supported with a minimum length of 48-inch Rehau pipe supports spaced a
    maximum distance of 10-inches between each Rehau Pipe Support Run. Tubing shall be
    marked [NSF®-fs ASTM E84 FS<=25/SD<=50].
    
[1] Flame Spread Index <= 25; Smoke Developed Index <= 50.

[3] Flame Spread Value (FSV) <= 25; Smoke Developed Value (SDV) <= 50.

[2] Flame Spread Index and Smoke Developed Index based on when tubing is field insulated
    with minimum 1/2" JM Microlok or Armaflex insulation as per Rehau installation
    instructions.
[3] Flame Spread Value (FSV) <= 25; Smoke Developed Value (SDV) <= 50.

** Flame Spread Index and Smoke Developed Index based on minimum spacing of 18 inches
   between tubing runs with Everloc+P, Everloc+ fittings.  Tubing shall be marked [NSF®-fs
   ASTM E84 FS<=25/SD<=50].
[1] Flame Spread Index <= 25; Smoke Developed Index <= 50.

* Flame Spread Index and Smoke Developed Index based on when tubing is field insulated
  with minimum 1/2" Microlok HP Hi performance fiberglass insulation as per Rehau
  installation instructions.
[1] Flame Spread Index <= 25; Smoke Developed Index <= 50.

*** Flame Spread Index and Smoke Developed Index based on ASTM E84 Steiner tunnel modified
    using piping supported with a minimum length of 48-inch Rehau pipe supports spaced a
    maximum distance of 10-inches between each Rehau Pipe Support Run. Tubing shall be
    marked [NSF®-fs ASTM E84 FS<=25/SD<=50].
    
[1] Flame Spread Index <= 25; Smoke Developed Index <= 50.

[1] Flame Spread Index <= 25; Smoke Developed Index <= 50.
**** Flame Spread Index and Smoke Developed Index based on when tubing is field insulated
     with minimum 1/2" Micro-lok HP Hi performance fiberglass insulation with
     Everloc+P/Everloc+ Fittings as per Rehau installation instructions. Tubing shall be
     marked [NSF®-fs ASTM E84 FS<=25/SD<=50].

[3] Flame Spread Value (FSV) <= 25; Smoke Developed Value (SDV) <= 50.

[2] Flame Spread Index and Smoke Developed Index based on when tubing is field insulated
    with minimum 1/2" JM Microlok or Armaflex insulation as per Rehau installation
    instructions.
[3] Flame Spread Value (FSV) <= 25; Smoke Developed Value (SDV) <= 50.

[3] Flame Spread Value (FSV) <= 25; Smoke Developed Value (SDV) <= 50.
[4] Flame Spread Index and Smoke Developed Index based on when tubing is field insulated
    with 1/2" Micro-lok HP Hi performance fiberglass insulation with Everloc+P/Everloc+
    Fittings as per Rehau installation instructions.
    Tubing shall be marked [cNSF®-fs CAN/ULC S102.2 FS<=25/SD<=50].

** Flame Spread Index and Smoke Developed Index based on minimum spacing of 18 inches
   between tubing runs with Everloc+P, Everloc+ fittings.  Tubing shall be marked [NSF®-fs
   ASTM E84 FS<=25/SD<=50].
[1] Flame Spread Index <= 25; Smoke Developed Index <= 50.

* Flame Spread Index and Smoke Developed Index based on when tubing is field insulated
  with minimum 1/2" Microlok HP Hi performance fiberglass insulation as per Rehau
  installation instructions.
[1] Flame Spread Index <= 25; Smoke Developed Index <= 50.

*** Flame Spread Index and Smoke Developed Index based on ASTM E84 Steiner tunnel modified
    using piping supported with a minimum length of 48-inch Rehau pipe supports spaced a
    maximum distance of 10-inches between each Rehau Pipe Support Run. Tubing shall be
    marked [NSF®-fs ASTM E84 FS<=25/SD<=50].
    
[1] Flame Spread Index <= 25; Smoke Developed Index <= 50.

[1] Flame Spread Index <= 25; Smoke Developed Index <= 50.
**** Flame Spread Index and Smoke Developed Index based on when tubing is field insulated
     with minimum 1/2" Micro-lok HP Hi performance fiberglass insulation with
     Everloc+P/Everloc+ Fittings as per Rehau installation instructions. Tubing shall be
     marked [NSF®-fs ASTM E84 FS<=25/SD<=50].

[3] Flame Spread Value (FSV) <= 25; Smoke Developed Value (SDV) <= 50.

[2] Flame Spread Index and Smoke Developed Index based on when tubing is field insulated
    with minimum 1/2" JM Microlok or Armaflex insulation as per Rehau installation
    instructions.
[3] Flame Spread Value (FSV) <= 25; Smoke Developed Value (SDV) <= 50.

[3] Flame Spread Value (FSV) <= 25; Smoke Developed Value (SDV) <= 50.
[4] Flame Spread Index and Smoke Developed Index based on when tubing is field insulated
    with 1/2" Micro-lok HP Hi performance fiberglass insulation with Everloc+P/Everloc+
    Fittings as per Rehau installation instructions.
    Tubing shall be marked [cNSF®-fs CAN/ULC S102.2 FS<=25/SD<=50].

** Flame Spread Index and Smoke Developed Index based on minimum spacing of 18 inches
   between tubing runs with Everloc+P, Everloc+ fittings.  Tubing shall be marked [NSF®-fs
   ASTM E84 FS<=25/SD<=50].
[1] Flame Spread Index <= 25; Smoke Developed Index <= 50.

* Flame Spread Index and Smoke Developed Index based on when tubing is field insulated
  with minimum 1/2" Microlok HP Hi performance fiberglass insulation as per Rehau
  installation instructions.
[1] Flame Spread Index <= 25; Smoke Developed Index <= 50.

*** Flame Spread Index and Smoke Developed Index based on ASTM E84 Steiner tunnel modified
    using piping supported with a minimum length of 48-inch Rehau pipe supports spaced a
    maximum distance of 10-inches between each Rehau Pipe Support Run. Tubing shall be
    marked [NSF®-fs ASTM E84 FS<=25/SD<=50].
    
[1] Flame Spread Index <= 25; Smoke Developed Index <= 50.

[1] Flame Spread Index <= 25; Smoke Developed Index <= 50.
**** Flame Spread Index and Smoke Developed Index based on when tubing is field insulated
     with minimum 1/2" Micro-lok HP Hi performance fiberglass insulation with
     Everloc+P/Everloc+ Fittings as per Rehau installation instructions. Tubing shall be
     marked [NSF®-fs ASTM E84 FS<=25/SD<=50].

[3] Flame Spread Value (FSV) <= 25; Smoke Developed Value (SDV) <= 50.

[2] Flame Spread Index and Smoke Developed Index based on when tubing is field insulated
    with minimum 1/2" JM Microlok or Armaflex insulation as per Rehau installation
    instructions.
[3] Flame Spread Value (FSV) <= 25; Smoke Developed Value (SDV) <= 50.

[3] Flame Spread Value (FSV) <= 25; Smoke Developed Value (SDV) <= 50.
[4] Flame Spread Index and Smoke Developed Index based on when tubing is field insulated
    with 1/2" Micro-lok HP Hi performance fiberglass insulation with Everloc+P/Everloc+
    Fittings as per Rehau installation instructions.
    Tubing shall be marked [cNSF®-fs CAN/ULC S102.2 FS<=25/SD<=50].

[2] Flame Spread Index and Smoke Developed Index based on when tubing is field insulated
    with minimum 1/2" JM Microlok or Armaflex insulation as per Rehau installation
    instructions.
[3] Flame Spread Value (FSV) <= 25; Smoke Developed Value (SDV) <= 50.

% PEX pipe and fittings are intended for use in multi-purpose piping systems of
  residential occupancies as defined in ANSI/NFPA 13D, “Installation of Sprinkler Systems
  in One- and Two- Family Dwellings and Manufactured Homes" and the International
  Residential Code, Section P2904, and are designed to withstand a working pressure of not
  less than 130 psi at 120°F.  PEX pipe and fittings are intended to be installed in
  accordance with the requirements specified in the manufacturer’s installation
  instructions and ANSI/NFPA 13D.  Protection is intended to be provided for PEX pipe and
  fittings in multi-purpose piping systems unless otherwise stated in this listing and per
  the installation and design manual dated September 11, 2008.  The minimum protection
  should consist of either (1) one layer of 3/8-in. gypsum wallboard, (2) a suspended
  membrane ceiling with lay-in panels or tiles having a weight of not less than 0.35 lbs
  per sq ft when installed with metallic support grids, OR (3) ½ in plywood.  PEX pipe and
  fittings are intended for use in areas where the maximum ambient temperature does not
  exceed 120°F. These pipe and fittings are not intended to be installed in outdoor
  applications.  The PEX pipe and fittings are intended for use in wet-pipe systems only
  and have not been evaluated for use in dry-pipe systems.  Raupex pipe and fittings may
  also be installed without protection (exposed) in accordance with the limitations
  specified in this installation and design manual dated September 11, 2008.
** Pipe and fittings Certified as a system using installation and design manual titled
   "FIREPEX Residential Fire Sprinkler Systems".
[G] Product is Certified to NSF/ANSI/CAN 372 and conforms with the lead content requirements
    for "lead free" plumbing as defined by California, Vermont, Maryland, and Louisiana
    state laws and the U.S. Safe Drinking Water Act.

* Accepted by NSF for use in residential and commercial construction, including
  manufactured housing.
^ Meets the chlorine resistance requirements of ASTM F876 when tested in accordance with
  ASTM F2023.
§ Product is Certified to the Uniform Plumbing Code™. Installation in accordance with the
  manufacturer's instructions and the requirements of the latest edition of the Uniform
  Plumbing Code™.
$$ Complies with US EPA Maximum Contaminant Levels (MCLs) for PFAS according to
   NSF/ANSI/CAN 61.
+++ Material complies with NSF/ANSI/CAN 61 health effects requirements when tested at
    temperatures up to and including Commercial Hot (180° F).
[G] Product is Certified to NSF/ANSI/CAN 372 and conforms with the lead content requirements
    for "lead free" plumbing as defined by California, Vermont, Maryland, and Louisiana
    state laws and the U.S. Safe Drinking Water Act.

* Accepted by NSF for use in residential and commercial construction, including
  manufactured housing.
^ Meets the chlorine resistance requirements of ASTM F876 when tested in accordance with
  ASTM F2023.
§ Product is Certified to the Uniform Plumbing Code™. Installation in accordance with the
  manufacturer's instructions and the requirements of the latest edition of the Uniform
  Plumbing Code™.
$$ Complies with US EPA Maximum Contaminant Levels (MCLs) for PFAS according to
   NSF/ANSI/CAN 61.
+++ Material complies with NSF/ANSI/CAN 61 health effects requirements when tested at
    temperatures up to and including Commercial Hot (180° F).
[G] Product is Certified to NSF/ANSI/CAN 372 and conforms with the lead content requirements
    for "lead free" plumbing as defined by California, Vermont, Maryland, and Louisiana
    state laws and the U.S. Safe Drinking Water Act.

* Accepted by NSF for use in residential and commercial construction, including
  manufactured housing.
^ Meets the chlorine resistance requirements of ASTM F876 when tested in accordance with
  ASTM F2023.
§ Product is Certified to the Uniform Plumbing Code™. Installation in accordance with the
  manufacturer's instructions and the requirements of the latest edition of the Uniform
  Plumbing Code™.
$$ Complies with US EPA Maximum Contaminant Levels (MCLs) for PFAS according to
   NSF/ANSI/CAN 61.
+++ Material complies with NSF/ANSI/CAN 61 health effects requirements when tested at
    temperatures up to and including Commercial Hot (180° F).
[G] Product is Certified to NSF/ANSI/CAN 372 and conforms with the lead content requirements
    for "lead free" plumbing as defined by California, Vermont, Maryland, and Louisiana
    state laws and the U.S. Safe Drinking Water Act.

% Tubing certified against CSA B137.5 shall include the standard designation(s) of the
  fitting system(s) for which the tubing is recommended by the manufacturer, and shall be
  marked, as applicable, with the following fitting system designation(s):  ASTM F877,
  F1807, F1960, F2080 and F2159.
* Accepted by NSF for use in residential and commercial construction, including
  manufactured housing.
^ Meets the chlorine resistance requirements of ASTM F876 when tested in accordance with
  ASTM F2023.
¢ Product is authorized to bear the cNSF and/or the cNSFus Mark.
§ Product is Certified to the Uniform Plumbing Code™. Installation in accordance with the
  manufacturer's instructions and the requirements of the latest edition of the Uniform
  Plumbing Code™.
$$ Complies with US EPA Maximum Contaminant Levels (MCLs) for PFAS according to
   NSF/ANSI/CAN 61.
+++ Material complies with NSF/ANSI/CAN 61 health effects requirements when tested at
    temperatures up to and including Commercial Hot (180° F).
[G] Product is Certified to NSF/ANSI/CAN 372 and conforms with the lead content requirements
    for "lead free" plumbing as defined by California, Vermont, Maryland, and Louisiana
    state laws and the U.S. Safe Drinking Water Act.

% Tubing certified against CSA B137.5 shall include the standard designation(s) of the
  fitting system(s) for which the tubing is recommended by the manufacturer, and shall be
  marked, as applicable, with the following fitting system designation(s):  ASTM F877,
  F1807, F1960, F2080 and F2159.
* Accepted by NSF for use in residential and commercial construction, including
  manufactured housing.
^ Meets the chlorine resistance requirements of ASTM F876 when tested in accordance with
  ASTM F2023.
¢ Product is authorized to bear the cNSF and/or the cNSFus Mark.
§ Product is Certified to the Uniform Plumbing Code™. Installation in accordance with the
  manufacturer's instructions and the requirements of the latest edition of the Uniform
  Plumbing Code™.
$$ Complies with US EPA Maximum Contaminant Levels (MCLs) for PFAS according to
   NSF/ANSI/CAN 61.
+++ Material complies with NSF/ANSI/CAN 61 health effects requirements when tested at
    temperatures up to and including Commercial Hot (180° F).
[G] Product is Certified to NSF/ANSI/CAN 372 and conforms with the lead content requirements
    for "lead free" plumbing as defined by California, Vermont, Maryland, and Louisiana
    state laws and the U.S. Safe Drinking Water Act.

* Accepted by NSF for use in residential and commercial construction, including
  manufactured housing.
^ Meets the chlorine resistance requirements of ASTM F876 when tested in accordance with
  ASTM F2023.
+++ Material complies with NSF/ANSI/CAN 61 health effects requirements when tested at
    temperatures up to and including Commercial Hot (180° F).
[G] Product is Certified to NSF/ANSI/CAN 372 and conforms with the lead content requirements
    for "lead free" plumbing as defined by California, Vermont, Maryland, and Louisiana
    state laws and the U.S. Safe Drinking Water Act.

* Accepted by NSF for use in residential and commercial construction, including
  manufactured housing.
^ Meets the chlorine resistance requirements of ASTM F876 when tested in accordance with
  ASTM F2023.
+++ Material complies with NSF/ANSI/CAN 61 health effects requirements when tested at
    temperatures up to and including Commercial Hot (180° F).
[G] Product is Certified to NSF/ANSI/CAN 372 and conforms with the lead content requirements
    for "lead free" plumbing as defined by California, Vermont, Maryland, and Louisiana
    state laws and the U.S. Safe Drinking Water Act.

% Tubing certified against CSA B137.5 shall include the standard designation(s) of the
  fitting system(s) for which the tubing is recommended by the manufacturer, and shall be
  marked, as applicable, with the following fitting system designation(s):  ASTM F877,
  F1807, F1960, F2080 and F2159.
* Accepted by NSF for use in residential and commercial construction, including
  manufactured housing.
^ Meets the chlorine resistance requirements of ASTM F876 when tested in accordance with
  ASTM F2023.
¢ Product is authorized to bear the cNSF and/or the cNSFus Mark.
§ Product is Certified to the Uniform Plumbing Code™. Installation in accordance with the
  manufacturer's instructions and the requirements of the latest edition of the Uniform
  Plumbing Code™.
+++ Material complies with NSF/ANSI/CAN 61 health effects requirements when tested at
    temperatures up to and including Commercial Hot (180° F).
[G] Product is Certified to NSF/ANSI/CAN 372 and conforms with the lead content requirements
    for "lead free" plumbing as defined by California, Vermont, Maryland, and Louisiana
    state laws and the U.S. Safe Drinking Water Act.

* Accepted by NSF for use in residential and commercial construction, including
  manufactured housing.
^ Meets the chlorine resistance requirements of ASTM F876 when tested in accordance with
  ASTM F2023.
§ Product is Certified to the Uniform Plumbing Code™. Installation in accordance with the
  manufacturer's instructions and the requirements of the latest edition of the Uniform
  Plumbing Code™.
$$ Complies with US EPA Maximum Contaminant Levels (MCLs) for PFAS according to
   NSF/ANSI/CAN 61.
+++ Material complies with NSF/ANSI/CAN 61 health effects requirements when tested at
    temperatures up to and including Commercial Hot (180° F).
[G] Product is Certified to NSF/ANSI/CAN 372 and conforms with the lead content requirements
    for "lead free" plumbing as defined by California, Vermont, Maryland, and Louisiana
    state laws and the U.S. Safe Drinking Water Act.

% Tubing certified against CSA B137.5 shall include the standard designation(s) of the
  fitting system(s) for which the tubing is recommended by the manufacturer, and shall be
  marked, as applicable, with the following fitting system designation(s):  ASTM F877,
  F1807, F1960, F2080 and F2159.
* Accepted by NSF for use in residential and commercial construction, including
  manufactured housing.
^ Meets the chlorine resistance requirements of ASTM F876 when tested in accordance with
  ASTM F2023.
¢ Product is authorized to bear the cNSF and/or the cNSFus Mark.
§ Product is Certified to the Uniform Plumbing Code™. Installation in accordance with the
  manufacturer's instructions and the requirements of the latest edition of the Uniform
  Plumbing Code™.
$$ Complies with US EPA Maximum Contaminant Levels (MCLs) for PFAS according to
   NSF/ANSI/CAN 61.
+++ Material complies with NSF/ANSI/CAN 61 health effects requirements when tested at
    temperatures up to and including Commercial Hot (180° F).
[G] Product is Certified to NSF/ANSI/CAN 372 and conforms with the lead content requirements
    for "lead free" plumbing as defined by California, Vermont, Maryland, and Louisiana
    state laws and the U.S. Safe Drinking Water Act.

* Accepted by NSF for use in residential and commercial construction, including
  manufactured housing.
^ Meets the chlorine resistance requirements of ASTM F876 when tested in accordance with
  ASTM F2023.
§ Product is Certified to the Uniform Plumbing Code™. Installation in accordance with the
  manufacturer's instructions and the requirements of the latest edition of the Uniform
  Plumbing Code™.
$$ Complies with US EPA Maximum Contaminant Levels (MCLs) for PFAS according to
   NSF/ANSI/CAN 61.
+++ Material complies with NSF/ANSI/CAN 61 health effects requirements when tested at
    temperatures up to and including Commercial Hot (180° F).
[G] Product is Certified to NSF/ANSI/CAN 372 and conforms with the lead content requirements
    for "lead free" plumbing as defined by California, Vermont, Maryland, and Louisiana
    state laws and the U.S. Safe Drinking Water Act.

% Tubing certified against CSA B137.5 shall include the standard designation(s) of the
  fitting system(s) for which the tubing is recommended by the manufacturer, and shall be
  marked, as applicable, with the following fitting system designation(s):  ASTM F877,
  F1807, F1960, F2080 and F2159.
* Accepted by NSF for use in residential and commercial construction, including
  manufactured housing.
^ Meets the chlorine resistance requirements of ASTM F876 when tested in accordance with
  ASTM F2023.
¢ Product is authorized to bear the cNSF and/or the cNSFus Mark.
§ Product is Certified to the Uniform Plumbing Code™. Installation in accordance with the
  manufacturer's instructions and the requirements of the latest edition of the Uniform
  Plumbing Code™.
$$ Complies with US EPA Maximum Contaminant Levels (MCLs) for PFAS according to
   NSF/ANSI/CAN 61.
+++ Material complies with NSF/ANSI/CAN 61 health effects requirements when tested at
    temperatures up to and including Commercial Hot (180° F).
[G] Product is Certified to NSF/ANSI/CAN 372 and conforms with the lead content requirements
    for "lead free" plumbing as defined by California, Vermont, Maryland, and Louisiana
    state laws and the U.S. Safe Drinking Water Act.

* Accepted by NSF for use in residential and commercial construction, including
  manufactured housing.
^ Meets the chlorine resistance requirements of ASTM F876 when tested in accordance with
  ASTM F2023.
§ Product is Certified to the Uniform Plumbing Code™. Installation in accordance with the
  manufacturer's instructions and the requirements of the latest edition of the Uniform
  Plumbing Code™.
$$ Complies with US EPA Maximum Contaminant Levels (MCLs) for PFAS according to
   NSF/ANSI/CAN 61.
+++ Material complies with NSF/ANSI/CAN 61 health effects requirements when tested at
    temperatures up to and including Commercial Hot (180° F).
[G] Product is Certified to NSF/ANSI/CAN 372 and conforms with the lead content requirements
    for "lead free" plumbing as defined by California, Vermont, Maryland, and Louisiana
    state laws and the U.S. Safe Drinking Water Act.

% Tubing certified against CSA B137.5 shall include the standard designation(s) of the
  fitting system(s) for which the tubing is recommended by the manufacturer, and shall be
  marked, as applicable, with the following fitting system designation(s):  ASTM F877,
  F1807, F1960, F2080 and F2159.
* Accepted by NSF for use in residential and commercial construction, including
  manufactured housing.
^ Meets the chlorine resistance requirements of ASTM F876 when tested in accordance with
  ASTM F2023.
¢ Product is authorized to bear the cNSF and/or the cNSFus Mark.
§ Product is Certified to the Uniform Plumbing Code™. Installation in accordance with the
  manufacturer's instructions and the requirements of the latest edition of the Uniform
  Plumbing Code™.
$$ Complies with US EPA Maximum Contaminant Levels (MCLs) for PFAS according to
   NSF/ANSI/CAN 61.
+++ Material complies with NSF/ANSI/CAN 61 health effects requirements when tested at
    temperatures up to and including Commercial Hot (180° F).
[G] Product is Certified to NSF/ANSI/CAN 372 and conforms with the lead content requirements
    for "lead free" plumbing as defined by California, Vermont, Maryland, and Louisiana
    state laws and the U.S. Safe Drinking Water Act.

* Accepted by NSF for use in residential and commercial construction, including
  manufactured housing.
^ Meets the chlorine resistance requirements of ASTM F876 when tested in accordance with
  ASTM F2023.
§ Product is Certified to the Uniform Plumbing Code™. Installation in accordance with the
  manufacturer's instructions and the requirements of the latest edition of the Uniform
  Plumbing Code™.
$$ Complies with US EPA Maximum Contaminant Levels (MCLs) for PFAS according to
   NSF/ANSI/CAN 61.
+++ Material complies with NSF/ANSI/CAN 61 health effects requirements when tested at
    temperatures up to and including Commercial Hot (180° F).
[G] Product is Certified to NSF/ANSI/CAN 372 and conforms with the lead content requirements
    for "lead free" plumbing as defined by California, Vermont, Maryland, and Louisiana
    state laws and the U.S. Safe Drinking Water Act.

% Tubing certified against CSA B137.5 shall include the standard designation(s) of the
  fitting system(s) for which the tubing is recommended by the manufacturer, and shall be
  marked, as applicable, with the following fitting system designation(s):  ASTM F877,
  F1807, F1960, F2080 and F2159.
* Accepted by NSF for use in residential and commercial construction, including
  manufactured housing.
^ Meets the chlorine resistance requirements of ASTM F876 when tested in accordance with
  ASTM F2023.
¢ Product is authorized to bear the cNSF and/or the cNSFus Mark.
§ Product is Certified to the Uniform Plumbing Code™. Installation in accordance with the
  manufacturer's instructions and the requirements of the latest edition of the Uniform
  Plumbing Code™.
$$ Complies with US EPA Maximum Contaminant Levels (MCLs) for PFAS according to
   NSF/ANSI/CAN 61.
+++ Material complies with NSF/ANSI/CAN 61 health effects requirements when tested at
    temperatures up to and including Commercial Hot (180° F).
[G] Product is Certified to NSF/ANSI/CAN 372 and conforms with the lead content requirements
    for "lead free" plumbing as defined by California, Vermont, Maryland, and Louisiana
    state laws and the U.S. Safe Drinking Water Act.

* Accepted by NSF for use in residential and commercial construction, including
  manufactured housing.
^ Meets the chlorine resistance requirements of ASTM F876 when tested in accordance with
  ASTM F2023.
§ Product is Certified to the Uniform Plumbing Code™. Installation in accordance with the
  manufacturer's instructions and the requirements of the latest edition of the Uniform
  Plumbing Code™.
$$ Complies with US EPA Maximum Contaminant Levels (MCLs) for PFAS according to
   NSF/ANSI/CAN 61.
+++ Material complies with NSF/ANSI/CAN 61 health effects requirements when tested at
    temperatures up to and including Commercial Hot (180° F).
[G] Product is Certified to NSF/ANSI/CAN 372 and conforms with the lead content requirements
    for "lead free" plumbing as defined by California, Vermont, Maryland, and Louisiana
    state laws and the U.S. Safe Drinking Water Act.

% Tubing certified against CSA B137.5 shall include the standard designation(s) of the
  fitting system(s) for which the tubing is recommended by the manufacturer, and shall be
  marked, as applicable, with the following fitting system designation(s):  ASTM F877,
  F1807, F1960, F2080 and F2159.
* Accepted by NSF for use in residential and commercial construction, including
  manufactured housing.
^ Meets the chlorine resistance requirements of ASTM F876 when tested in accordance with
  ASTM F2023.
¢ Product is authorized to bear the cNSF and/or the cNSFus Mark.
§ Product is Certified to the Uniform Plumbing Code™. Installation in accordance with the
  manufacturer's instructions and the requirements of the latest edition of the Uniform
  Plumbing Code™.
$$ Complies with US EPA Maximum Contaminant Levels (MCLs) for PFAS according to
   NSF/ANSI/CAN 61.
+++ Material complies with NSF/ANSI/CAN 61 health effects requirements when tested at
    temperatures up to and including Commercial Hot (180° F).
[G] Product is Certified to NSF/ANSI/CAN 372 and conforms with the lead content requirements
    for "lead free" plumbing as defined by California, Vermont, Maryland, and Louisiana
    state laws and the U.S. Safe Drinking Water Act.

* Accepted by NSF for use in residential and commercial construction, including
  manufactured housing.
^ Meets the chlorine resistance requirements of ASTM F876 when tested in accordance with
  ASTM F2023.
§ Product is Certified to the Uniform Plumbing Code™. Installation in accordance with the
  manufacturer's instructions and the requirements of the latest edition of the Uniform
  Plumbing Code™.
$$ Complies with US EPA Maximum Contaminant Levels (MCLs) for PFAS according to
   NSF/ANSI/CAN 61.
+++ Material complies with NSF/ANSI/CAN 61 health effects requirements when tested at
    temperatures up to and including Commercial Hot (180° F).
[G] Product is Certified to NSF/ANSI/CAN 372 and conforms with the lead content requirements
    for "lead free" plumbing as defined by California, Vermont, Maryland, and Louisiana
    state laws and the U.S. Safe Drinking Water Act.

% Tubing certified against CSA B137.5 shall include the standard designation(s) of the
  fitting system(s) for which the tubing is recommended by the manufacturer, and shall be
  marked, as applicable, with the following fitting system designation(s):  ASTM F877,
  F1807, F1960, F2080 and F2159.
* Accepted by NSF for use in residential and commercial construction, including
  manufactured housing.
^ Meets the chlorine resistance requirements of ASTM F876 when tested in accordance with
  ASTM F2023.
¢ Product is authorized to bear the cNSF and/or the cNSFus Mark.
§ Product is Certified to the Uniform Plumbing Code™. Installation in accordance with the
  manufacturer's instructions and the requirements of the latest edition of the Uniform
  Plumbing Code™.
$$ Complies with US EPA Maximum Contaminant Levels (MCLs) for PFAS according to
   NSF/ANSI/CAN 61.
+++ Material complies with NSF/ANSI/CAN 61 health effects requirements when tested at
    temperatures up to and including Commercial Hot (180° F).
[G] Product is Certified to NSF/ANSI/CAN 372 and conforms with the lead content requirements
    for "lead free" plumbing as defined by California, Vermont, Maryland, and Louisiana
    state laws and the U.S. Safe Drinking Water Act.

¢ Product is authorized to bear the cNSF and/or the cNSFus Mark.
§ Product is Certified to the Uniform Plumbing Code™. Installation in accordance with the
  manufacturer's instructions and the requirements of the latest edition of the Uniform
  Plumbing Code™.

¢ Product is authorized to bear the cNSF and/or the cNSFus Mark.
§ Product is Certified to the Uniform Plumbing Code™. Installation in accordance with the
  manufacturer's instructions and the requirements of the latest edition of the Uniform
  Plumbing Code™.

§ Product is Certified to the Uniform Plumbing Code™. Installation in accordance with the
  manufacturer's instructions and the requirements of the latest edition of the Uniform
  Plumbing Code™.

§ Product is Certified to the Uniform Plumbing Code™. Installation in accordance with the
  manufacturer's instructions and the requirements of the latest edition of the Uniform
  Plumbing Code™.

% Tubing certified against CSA B137.5 shall include the standard designation(s) of the
  fitting system(s) for which the tubing is recommended by the manufacturer, and shall be
  marked, as
  applicable, with the following fitting system designation(s): AWWA C800.
¢ Product is authorized to bear the cNSF and/or the cNSFus Mark.

% Tubing certified against CSA B137.5 shall include the standard designation(s) of the
  fitting system(s) for which the tubing is recommended by the manufacturer,  and shall be
  marked, as applicable, with the following fitting system designation(s): AWWA C800.
¢ Product is authorized to bear the cNSF and/or the cNSFus Mark.

¢ Product is authorized to bear the cNSF and/or the cNSFus Mark.

^ Meets the chlorine resistance requirements of ASTM F876 when tested in accordance with
  ASTM F2023.
¢ Product is authorized to bear the cNSF and/or the cNSFus Mark.

% Tubing certified against CSA B137.5 shall include the standard designation(s) of the
  fitting system(s) for which the tubing is recommended by the manufacturer, and shall be
  marked, as applicable, with the following fitting system designation(s):  ASTM F877,
  F1807, F1960, F2080 and F2159.
^ Meets the chlorine resistance requirements of ASTM F876 when tested in accordance with
  ASTM F2023.
¢ Product is authorized to bear the cNSF and/or the cNSFus Mark.

$ Non-barrier pipe.
* Accepted by NSF for use in residential and commercial construction, including
  manufactured housing.
^ Meets the chlorine resistance requirements of ASTM F876 when tested in accordance with
  ASTM F2023.
§ Product is Certified to the Uniform Plumbing Code™. Installation in accordance with the
  manufacturer's instructions and the requirements of the latest edition of the Uniform
  Plumbing Code™.

$ Non-barrier pipe.
% Tubing certified against CSA B137.5 shall include the standard designation(s) of the
  fitting system(s) for which the tubing is recommended by the manufacturer, and shall be
  marked, as applicable, with the following fitting system designation(s):  ASTM F877,
  F1807, F1960, F2080 and F2159.
* Accepted by NSF for use in residential and commercial construction, including
  manufactured housing.
§ Product is Certified to the Uniform Plumbing Code™. Installation in accordance with the
  manufacturer's instructions and the requirements of the latest edition of the Uniform
  Plumbing Code™.

* Accepted by NSF for use in residential and commercial construction, including
  manufactured housing.
¥ Product is Certified to the Uniform Mechanical Code™. Installation in accordance with
  the manufacturer's instructions and the requirements of the latest edition of the
  Uniform Mechanical Code™.

* Accepted by NSF for use in residential and commercial construction, including
  manufactured housing.
¥ Product is Certified to the Uniform Mechanical Code™. Installation in accordance with
  the manufacturer's instructions and the requirements of the latest edition of the
  Uniform Mechanical Code™.

% Tubing certified against CSA B137.5 shall include the standard designation(s) of the
  fitting system(s) for which the tubing is recommended by the manufacturer, and shall be
  marked, as applicable, with the following fitting system designation(s):  ASTM F877,
  F1807, F1960, F2080 and F2159.
* Accepted by NSF for use in residential and commercial construction, including
  manufactured housing.
¢ Product is authorized to bear the cNSF and/or the cNSFus Mark.
¥ Product is Certified to the Uniform Mechanical Code™. Installation in accordance with
  the manufacturer's instructions and the requirements of the latest edition of the
  Uniform Mechanical Code™.

# Insulated material has not been evaluated to Standard 14 Requirements, only Standard 61.
* Accepted by NSF for use in residential and commercial construction, including
  manufactured housing.
^ Meets the chlorine resistance requirements of ASTM F876 when tested in accordance with
  ASTM F2023.
§ Product is Certified to the Uniform Plumbing Code™. Installation in accordance with the
  manufacturer's instructions and the requirements of the latest edition of the Uniform
  Plumbing Code™.
+++ Material complies with NSF/ANSI/CAN 61 health effects requirements when tested at
    temperatures up to and including Commercial Hot (180° F).
[G] Product is Certified to NSF/ANSI/CAN 372 and conforms with the lead content requirements
    for "lead free" plumbing as defined by California, Vermont, Maryland, and Louisiana
    state laws and the U.S. Safe Drinking Water Act.

# Insulated material has not been evaluated to Standard 14 Requirements, only Standard 61.
* Accepted by NSF for use in residential and commercial construction, including
  manufactured housing.
^ Meets the chlorine resistance requirements of ASTM F876 when tested in accordance with
  ASTM F2023.
§ Product is Certified to the Uniform Plumbing Code™. Installation in accordance with the
  manufacturer's instructions and the requirements of the latest edition of the Uniform
  Plumbing Code™.
+++ Material complies with NSF/ANSI/CAN 61 health effects requirements when tested at
    temperatures up to and including Commercial Hot (180° F).
[G] Product is Certified to NSF/ANSI/CAN 372 and conforms with the lead content requirements
    for "lead free" plumbing as defined by California, Vermont, Maryland, and Louisiana
    state laws and the U.S. Safe Drinking Water Act.

# Insulated material has not been evaluated to Standard 14 Requirements, only Standard 61.
& Tubing certified against CSA B137.5 shall include the standard designation(s) of the
  fitting system(s) for which the tubing is recommended by the manufacturer, and shall be
  marked, as applicable, with the following fitting system designation(s): AWWA C800.
* Accepted by NSF for use in residential and commercial construction, including
  manufactured housing.
^ Meets the chlorine resistance requirements of ASTM F876 when tested in accordance with
  ASTM F2023.
¢ Product is authorized to bear the cNSF and/or the cNSFus Mark.
§ Product is Certified to the Uniform Plumbing Code™. Installation in accordance with the
  manufacturer's instructions and the requirements of the latest edition of the Uniform
  Plumbing Code™.
+++ Material complies with NSF/ANSI/CAN 61 health effects requirements when tested at
    temperatures up to and including Commercial Hot (180° F).
[G] Product is Certified to NSF/ANSI/CAN 372 and conforms with the lead content requirements
    for "lead free" plumbing as defined by California, Vermont, Maryland, and Louisiana
    state laws and the U.S. Safe Drinking Water Act.

# Insulated material has not been evaluated to Standard 14 Requirements, only Standard 61.
% Tubing certified against CSA B137.5 shall include the standard designation(s) of the
  fitting system(s) for which the tubing is recommended by the manufacturer, and shall be
  marked, as applicable, with the following fitting system designation(s): ASTM F877,
  F1807, F1960, F2080 and F2159.
* Accepted by NSF for use in residential and commercial construction, including
  manufactured housing.
^ Meets the chlorine resistance requirements of ASTM F876 when tested in accordance with
  ASTM F2023.
¢ Product is authorized to bear the cNSF and/or the cNSFus Mark.
§ Product is Certified to the Uniform Plumbing Code™. Installation in accordance with the
  manufacturer's instructions and the requirements of the latest edition of the Uniform
  Plumbing Code™.
+++ Material complies with NSF/ANSI/CAN 61 health effects requirements when tested at
    temperatures up to and including Commercial Hot (180° F).
[G] Product is Certified to NSF/ANSI/CAN 372 and conforms with the lead content requirements
    for "lead free" plumbing as defined by California, Vermont, Maryland, and Louisiana
    state laws and the U.S. Safe Drinking Water Act.

# Insulated material has not been evaluated to Standard 14 Requirements, only Standard 61.
* Accepted by NSF for use in residential and commercial construction, including
  manufactured housing.
^ Meets the chlorine resistance requirements of ASTM F876 when tested in accordance with
  ASTM F2023.
§ Product is Certified to the Uniform Plumbing Code™. Installation in accordance with the
  manufacturer's instructions and the requirements of the latest edition of the Uniform
  Plumbing Code™.
+++ Material complies with NSF/ANSI/CAN 61 health effects requirements when tested at
    temperatures up to and including Commercial Hot (180° F).
[G] Product is Certified to NSF/ANSI/CAN 372 and conforms with the lead content requirements
    for "lead free" plumbing as defined by California, Vermont, Maryland, and Louisiana
    state laws and the U.S. Safe Drinking Water Act.

# Insulated material has not been evaluated to Standard 14 Requirements, only Standard 61.
* Accepted by NSF for use in residential and commercial construction, including
  manufactured housing.
^ Meets the chlorine resistance requirements of ASTM F876 when tested in accordance with
  ASTM F2023.
§ Product is Certified to the Uniform Plumbing Code™. Installation in accordance with the
  manufacturer's instructions and the requirements of the latest edition of the Uniform
  Plumbing Code™.
+++ Material complies with NSF/ANSI/CAN 61 health effects requirements when tested at
    temperatures up to and including Commercial Hot (180° F).
[G] Product is Certified to NSF/ANSI/CAN 372 and conforms with the lead content requirements
    for "lead free" plumbing as defined by California, Vermont, Maryland, and Louisiana
    state laws and the U.S. Safe Drinking Water Act.

# Insulated material has not been evaluated to Standard 14 Requirements, only Standard 61.
% Tubing certified against CSA B137.5 shall include the standard designation(s) of the
  fitting system(s) for which the tubing is recommended by the manufacturer, and shall be
  marked, as applicable, with the following fitting system designation(s): ASTM F877,
  F1807, F1960, F2080 and F2159.
* Accepted by NSF for use in residential and commercial construction, including
  manufactured housing.
^ Meets the chlorine resistance requirements of ASTM F876 when tested in accordance with
  ASTM F2023.
¢ Product is authorized to bear the cNSF and/or the cNSFus Mark.
§ Product is Certified to the Uniform Plumbing Code™. Installation in accordance with the
  manufacturer's instructions and the requirements of the latest edition of the Uniform
  Plumbing Code™.
+++ Material complies with NSF/ANSI/CAN 61 health effects requirements when tested at
    temperatures up to and including Commercial Hot (180° F).
[G] Product is Certified to NSF/ANSI/CAN 372 and conforms with the lead content requirements
    for "lead free" plumbing as defined by California, Vermont, Maryland, and Louisiana
    state laws and the U.S. Safe Drinking Water Act.

# Insulated material has not been evaluated to Standard 14 Requirements, only Standard 61.
* Accepted by NSF for use in residential and commercial construction, including
  manufactured housing.
^ Meets the chlorine resistance requirements of ASTM F876 when tested in accordance with
  ASTM F2023.
§ Product is Certified to the Uniform Plumbing Code™. Installation in accordance with the
  manufacturer's instructions and the requirements of the latest edition of the Uniform
  Plumbing Code™.
+++ Material complies with NSF/ANSI/CAN 61 health effects requirements when tested at
    temperatures up to and including Commercial Hot (180° F).
[G] Product is Certified to NSF/ANSI/CAN 372 and conforms with the lead content requirements
    for "lead free" plumbing as defined by California, Vermont, Maryland, and Louisiana
    state laws and the U.S. Safe Drinking Water Act.

# Insulated material has not been evaluated to Standard 14 Requirements, only Standard 61.
% Tubing certified against CSA B137.5 shall include the standard designation(s) of the
  fitting system(s) for which the tubing is recommended by the manufacturer, and shall be
  marked, as applicable, with the following fitting system designation(s): ASTM F877,
  F1807, F1960, F2080 and F2159.
* Accepted by NSF for use in residential and commercial construction, including
  manufactured housing.
^ Meets the chlorine resistance requirements of ASTM F876 when tested in accordance with
  ASTM F2023.
¢ Product is authorized to bear the cNSF and/or the cNSFus Mark.
§ Product is Certified to the Uniform Plumbing Code™. Installation in accordance with the
  manufacturer's instructions and the requirements of the latest edition of the Uniform
  Plumbing Code™.
+++ Material complies with NSF/ANSI/CAN 61 health effects requirements when tested at
    temperatures up to and including Commercial Hot (180° F).
[G] Product is Certified to NSF/ANSI/CAN 372 and conforms with the lead content requirements
    for "lead free" plumbing as defined by California, Vermont, Maryland, and Louisiana
    state laws and the U.S. Safe Drinking Water Act.

! Product is Certified whether or not it bears the U.P. Code Mark.
§ Product is Certified to the Uniform Plumbing Code™. Installation in accordance with the
  manufacturer's instructions and the requirements of the latest edition of the Uniform
  Plumbing Code™.
+++ Material complies with NSF/ANSI/CAN 61 health effects requirements when tested at
    temperatures up to and including Commercial Hot (180° F).
[G] Product is Certified to NSF/ANSI/CAN 372 and conforms with the lead content requirements
    for "lead free" plumbing as defined by California, Vermont, Maryland, and Louisiana
    state laws and the U.S. Safe Drinking Water Act.

! Product is Certified whether or not it bears the U.P. Code Mark.
¢ Product is authorized to bear the cNSF and/or the cNSFus Mark.
§ Product is Certified to the Uniform Plumbing Code™. Installation in accordance with the
  manufacturer's instructions and the requirements of the latest edition of the Uniform
  Plumbing Code™.
+++ Material complies with NSF/ANSI/CAN 61 health effects requirements when tested at
    temperatures up to and including Commercial Hot (180° F).
[G] Product is Certified to NSF/ANSI/CAN 372 and conforms with the lead content requirements
    for "lead free" plumbing as defined by California, Vermont, Maryland, and Louisiana
    state laws and the U.S. Safe Drinking Water Act.

! Product is Certified whether or not it bears the U.P. Code Mark.
§ Product is Certified to the Uniform Plumbing Code™. Installation in accordance with the
  manufacturer's instructions and the requirements of the latest edition of the Uniform
  Plumbing Code™.
+++ Material complies with NSF/ANSI/CAN 61 health effects requirements when tested at
    temperatures up to and including Commercial Hot (180° F).
[G] Product is Certified to NSF/ANSI/CAN 372 and conforms with the lead content requirements
    for "lead free" plumbing as defined by California, Vermont, Maryland, and Louisiana
    state laws and the U.S. Safe Drinking Water Act.

! Product is Certified whether or not it bears the U.P. Code Mark.
¢ Product is authorized to bear the cNSF and/or the cNSFus Mark.
§ Product is Certified to the Uniform Plumbing Code™. Installation in accordance with the
  manufacturer's instructions and the requirements of the latest edition of the Uniform
  Plumbing Code™.
+++ Material complies with NSF/ANSI/CAN 61 health effects requirements when tested at
    temperatures up to and including Commercial Hot (180° F).
[G] Product is Certified to NSF/ANSI/CAN 372 and conforms with the lead content requirements
    for "lead free" plumbing as defined by California, Vermont, Maryland, and Louisiana
    state laws and the U.S. Safe Drinking Water Act.

! Product is Certified whether or not it bears the U.P. Code Mark.
§ Product is Certified to the Uniform Plumbing Code™. Installation in accordance with the
  manufacturer's instructions and the requirements of the latest edition of the Uniform
  Plumbing Code™.
+++ Material complies with NSF/ANSI/CAN 61 health effects requirements when tested at
    temperatures up to and including Commercial Hot (180° F).
[G] Product is Certified to NSF/ANSI/CAN 372 and conforms with the lead content requirements
    for "lead free" plumbing as defined by California, Vermont, Maryland, and Louisiana
    state laws and the U.S. Safe Drinking Water Act.

! Product is Certified whether or not it bears the U.P. Code Mark.
¢ Product is authorized to bear the cNSF and/or the cNSFus Mark.
§ Product is Certified to the Uniform Plumbing Code™. Installation in accordance with the
  manufacturer's instructions and the requirements of the latest edition of the Uniform
  Plumbing Code™.
+++ Material complies with NSF/ANSI/CAN 61 health effects requirements when tested at
    temperatures up to and including Commercial Hot (180° F).
[G] Product is Certified to NSF/ANSI/CAN 372 and conforms with the lead content requirements
    for "lead free" plumbing as defined by California, Vermont, Maryland, and Louisiana
    state laws and the U.S. Safe Drinking Water Act.

! Product is Certified whether or not it bears the U.P. Code Mark.
§ Product is Certified to the Uniform Plumbing Code™. Installation in accordance with the
  manufacturer's instructions and the requirements of the latest edition of the Uniform
  Plumbing Code™.
+++ Material complies with NSF/ANSI/CAN 61 health effects requirements when tested at
    temperatures up to and including Commercial Hot (180° F).
[G] Product is Certified to NSF/ANSI/CAN 372 and conforms with the lead content requirements
    for "lead free" plumbing as defined by California, Vermont, Maryland, and Louisiana
    state laws and the U.S. Safe Drinking Water Act.

! Product is Certified whether or not it bears the U.P. Code Mark.
¢ Product is authorized to bear the cNSF and/or the cNSFus Mark.
§ Product is Certified to the Uniform Plumbing Code™. Installation in accordance with the
  manufacturer's instructions and the requirements of the latest edition of the Uniform
  Plumbing Code™.
+++ Material complies with NSF/ANSI/CAN 61 health effects requirements when tested at
    temperatures up to and including Commercial Hot (180° F).
[G] Product is Certified to NSF/ANSI/CAN 372 and conforms with the lead content requirements
    for "lead free" plumbing as defined by California, Vermont, Maryland, and Louisiana
    state laws and the U.S. Safe Drinking Water Act.

! Product is Certified whether or not it bears the U.P. Code Mark.
§ Product is Certified to the Uniform Plumbing Code™. Installation in accordance with the
  manufacturer's instructions and the requirements of the latest edition of the Uniform
  Plumbing Code™.
+++ Material complies with NSF/ANSI/CAN 61 health effects requirements when tested at
    temperatures up to and including Commercial Hot (180° F).
[G] Product is Certified to NSF/ANSI/CAN 372 and conforms with the lead content requirements
    for "lead free" plumbing as defined by California, Vermont, Maryland, and Louisiana
    state laws and the U.S. Safe Drinking Water Act.

! Product is Certified whether or not it bears the U.P. Code Mark.
¢ Product is authorized to bear the cNSF and/or the cNSFus Mark.
§ Product is Certified to the Uniform Plumbing Code™. Installation in accordance with the
  manufacturer's instructions and the requirements of the latest edition of the Uniform
  Plumbing Code™.
+++ Material complies with NSF/ANSI/CAN 61 health effects requirements when tested at
    temperatures up to and including Commercial Hot (180° F).
[G] Product is Certified to NSF/ANSI/CAN 372 and conforms with the lead content requirements
    for "lead free" plumbing as defined by California, Vermont, Maryland, and Louisiana
    state laws and the U.S. Safe Drinking Water Act.

! Product is Certified whether or not it bears the U.P. Code Mark.
§ Product is Certified to the Uniform Plumbing Code™. Installation in accordance with the
  manufacturer's instructions and the requirements of the latest edition of the Uniform
  Plumbing Code™.
+++ Material complies with NSF/ANSI/CAN 61 health effects requirements when tested at
    temperatures up to and including Commercial Hot (180° F).
[G] Product is Certified to NSF/ANSI/CAN 372 and conforms with the lead content requirements
    for "lead free" plumbing as defined by California, Vermont, Maryland, and Louisiana
    state laws and the U.S. Safe Drinking Water Act.

! Product is Certified whether or not it bears the U.P. Code Mark.
¢ Product is authorized to bear the cNSF and/or the cNSFus Mark.
§ Product is Certified to the Uniform Plumbing Code™. Installation in accordance with the
  manufacturer's instructions and the requirements of the latest edition of the Uniform
  Plumbing Code™.
+++ Material complies with NSF/ANSI/CAN 61 health effects requirements when tested at
    temperatures up to and including Commercial Hot (180° F).
[G] Product is Certified to NSF/ANSI/CAN 372 and conforms with the lead content requirements
    for "lead free" plumbing as defined by California, Vermont, Maryland, and Louisiana
    state laws and the U.S. Safe Drinking Water Act.

! Product is Certified whether or not it bears the U.P. Code Mark.
§ Product is Certified to the Uniform Plumbing Code™. Installation in accordance with the
  manufacturer's instructions and the requirements of the latest edition of the Uniform
  Plumbing Code™.
+++ Material complies with NSF/ANSI/CAN 61 health effects requirements when tested at
    temperatures up to and including Commercial Hot (180° F).
[G] Product is Certified to NSF/ANSI/CAN 372 and conforms with the lead content requirements
    for "lead free" plumbing as defined by California, Vermont, Maryland, and Louisiana
    state laws and the U.S. Safe Drinking Water Act.

! Product is Certified whether or not it bears the U.P. Code Mark.
¢ Product is authorized to bear the cNSF and/or the cNSFus Mark.
§ Product is Certified to the Uniform Plumbing Code™. Installation in accordance with the
  manufacturer's instructions and the requirements of the latest edition of the Uniform
  Plumbing Code™.
+++ Material complies with NSF/ANSI/CAN 61 health effects requirements when tested at
    temperatures up to and including Commercial Hot (180° F).
[G] Product is Certified to NSF/ANSI/CAN 372 and conforms with the lead content requirements
    for "lead free" plumbing as defined by California, Vermont, Maryland, and Louisiana
    state laws and the U.S. Safe Drinking Water Act.

! Product is Certified whether or not it bears the U.P. Code Mark.
§ Product is Certified to the Uniform Plumbing Code™. Installation in accordance with the
  manufacturer's instructions and the requirements of the latest edition of the Uniform
  Plumbing Code™.
+++ Material complies with NSF/ANSI/CAN 61 health effects requirements when tested at
    temperatures up to and including Commercial Hot (180° F).
[G] Product is Certified to NSF/ANSI/CAN 372 and conforms with the lead content requirements
    for "lead free" plumbing as defined by California, Vermont, Maryland, and Louisiana
    state laws and the U.S. Safe Drinking Water Act.

! Product is Certified whether or not it bears the U.P. Code Mark.
¢ Product is authorized to bear the cNSF and/or the cNSFus Mark.
§ Product is Certified to the Uniform Plumbing Code™. Installation in accordance with the
  manufacturer's instructions and the requirements of the latest edition of the Uniform
  Plumbing Code™.
+++ Material complies with NSF/ANSI/CAN 61 health effects requirements when tested at
    temperatures up to and including Commercial Hot (180° F).
[G] Product is Certified to NSF/ANSI/CAN 372 and conforms with the lead content requirements
    for "lead free" plumbing as defined by California, Vermont, Maryland, and Louisiana
    state laws and the U.S. Safe Drinking Water Act.

! Product is Certified whether or not it bears the U.P. Code Mark.
§ Product is Certified to the Uniform Plumbing Code™. Installation in accordance with the
  manufacturer's instructions and the requirements of the latest edition of the Uniform
  Plumbing Code™.
+++ Material complies with NSF/ANSI/CAN 61 health effects requirements when tested at
    temperatures up to and including Commercial Hot (180° F).
[G] Product is Certified to NSF/ANSI/CAN 372 and conforms with the lead content requirements
    for "lead free" plumbing as defined by California, Vermont, Maryland, and Louisiana
    state laws and the U.S. Safe Drinking Water Act.

! Product is Certified whether or not it bears the U.P. Code Mark.
¢ Product is authorized to bear the cNSF and/or the cNSFus Mark.
§ Product is Certified to the Uniform Plumbing Code™. Installation in accordance with the
  manufacturer's instructions and the requirements of the latest edition of the Uniform
  Plumbing Code™.
+++ Material complies with NSF/ANSI/CAN 61 health effects requirements when tested at
    temperatures up to and including Commercial Hot (180° F).
[G] Product is Certified to NSF/ANSI/CAN 372 and conforms with the lead content requirements
    for "lead free" plumbing as defined by California, Vermont, Maryland, and Louisiana
    state laws and the U.S. Safe Drinking Water Act.

! Product is Certified whether or not it bears the U.P. Code Mark.
§ Product is Certified to the Uniform Plumbing Code™. Installation in accordance with the
  manufacturer's instructions and the requirements of the latest edition of the Uniform
  Plumbing Code™.
+++ Material complies with NSF/ANSI/CAN 61 health effects requirements when tested at
    temperatures up to and including Commercial Hot (180° F).
[G] Product is Certified to NSF/ANSI/CAN 372 and conforms with the lead content requirements
    for "lead free" plumbing as defined by California, Vermont, Maryland, and Louisiana
    state laws and the U.S. Safe Drinking Water Act.

! Product is Certified whether or not it bears the U.P. Code Mark.
¢ Product is authorized to bear the cNSF and/or the cNSFus Mark.
§ Product is Certified to the Uniform Plumbing Code™. Installation in accordance with the
  manufacturer's instructions and the requirements of the latest edition of the Uniform
  Plumbing Code™.
+++ Material complies with NSF/ANSI/CAN 61 health effects requirements when tested at
    temperatures up to and including Commercial Hot (180° F).
[G] Product is Certified to NSF/ANSI/CAN 372 and conforms with the lead content requirements
    for "lead free" plumbing as defined by California, Vermont, Maryland, and Louisiana
    state laws and the U.S. Safe Drinking Water Act.

! Product is Certified whether or not it bears the U.P. Code Mark.
§ Product is Certified to the Uniform Plumbing Code™. Installation in accordance with the
  manufacturer's instructions and the requirements of the latest edition of the Uniform
  Plumbing Code™.
+++ Material complies with NSF/ANSI/CAN 61 health effects requirements when tested at
    temperatures up to and including Commercial Hot (180° F).
[G] Product is Certified to NSF/ANSI/CAN 372 and conforms with the lead content requirements
    for "lead free" plumbing as defined by California, Vermont, Maryland, and Louisiana
    state laws and the U.S. Safe Drinking Water Act.

! Product is Certified whether or not it bears the U.P. Code Mark.
¢ Product is authorized to bear the cNSF and/or the cNSFus Mark.
§ Product is Certified to the Uniform Plumbing Code™. Installation in accordance with the
  manufacturer's instructions and the requirements of the latest edition of the Uniform
  Plumbing Code™.
+++ Material complies with NSF/ANSI/CAN 61 health effects requirements when tested at
    temperatures up to and including Commercial Hot (180° F).
[G] Product is Certified to NSF/ANSI/CAN 372 and conforms with the lead content requirements
    for "lead free" plumbing as defined by California, Vermont, Maryland, and Louisiana
    state laws and the U.S. Safe Drinking Water Act.

! Product is Certified whether or not it bears the U.P. Code Mark.
§ Product is Certified to the Uniform Plumbing Code™. Installation in accordance with the
  manufacturer's instructions and the requirements of the latest edition of the Uniform
  Plumbing Code™.
+++ Material complies with NSF/ANSI/CAN 61 health effects requirements when tested at
    temperatures up to and including Commercial Hot (180° F).
[G] Product is Certified to NSF/ANSI/CAN 372 and conforms with the lead content requirements
    for "lead free" plumbing as defined by California, Vermont, Maryland, and Louisiana
    state laws and the U.S. Safe Drinking Water Act.

! Product is Certified whether or not it bears the U.P. Code Mark.
¢ Product is authorized to bear the cNSF and/or the cNSFus Mark.
§ Product is Certified to the Uniform Plumbing Code™. Installation in accordance with the
  manufacturer's instructions and the requirements of the latest edition of the Uniform
  Plumbing Code™.
+++ Material complies with NSF/ANSI/CAN 61 health effects requirements when tested at
    temperatures up to and including Commercial Hot (180° F).
[G] Product is Certified to NSF/ANSI/CAN 372 and conforms with the lead content requirements
    for "lead free" plumbing as defined by California, Vermont, Maryland, and Louisiana
    state laws and the U.S. Safe Drinking Water Act.

! Product is Certified whether or not it bears the U.P. Code Mark.
§ Product is Certified to the Uniform Plumbing Code™. Installation in accordance with the
  manufacturer's instructions and the requirements of the latest edition of the Uniform
  Plumbing Code™.
+++ Material complies with NSF/ANSI/CAN 61 health effects requirements when tested at
    temperatures up to and including Commercial Hot (180° F).
[G] Product is Certified to NSF/ANSI/CAN 372 and conforms with the lead content requirements
    for "lead free" plumbing as defined by California, Vermont, Maryland, and Louisiana
    state laws and the U.S. Safe Drinking Water Act.

! Product is Certified whether or not it bears the U.P. Code Mark.
¢ Product is authorized to bear the cNSF and/or the cNSFus Mark.
§ Product is Certified to the Uniform Plumbing Code™. Installation in accordance with the
  manufacturer's instructions and the requirements of the latest edition of the Uniform
  Plumbing Code™.
+++ Material complies with NSF/ANSI/CAN 61 health effects requirements when tested at
    temperatures up to and including Commercial Hot (180° F).
[G] Product is Certified to NSF/ANSI/CAN 372 and conforms with the lead content requirements
    for "lead free" plumbing as defined by California, Vermont, Maryland, and Louisiana
    state laws and the U.S. Safe Drinking Water Act.

! Product is Certified whether or not it bears the U.P. Code Mark.
§ Product is Certified to the Uniform Plumbing Code™. Installation in accordance with the
  manufacturer's instructions and the requirements of the latest edition of the Uniform
  Plumbing Code™.
+++ Material complies with NSF/ANSI/CAN 61 health effects requirements when tested at
    temperatures up to and including Commercial Hot (180° F).
[G] Product is Certified to NSF/ANSI/CAN 372 and conforms with the lead content requirements
    for "lead free" plumbing as defined by California, Vermont, Maryland, and Louisiana
    state laws and the U.S. Safe Drinking Water Act.

! Product is Certified whether or not it bears the U.P. Code Mark.
¢ Product is authorized to bear the cNSF and/or the cNSFus Mark.
§ Product is Certified to the Uniform Plumbing Code™. Installation in accordance with the
  manufacturer's instructions and the requirements of the latest edition of the Uniform
  Plumbing Code™.
+++ Material complies with NSF/ANSI/CAN 61 health effects requirements when tested at
    temperatures up to and including Commercial Hot (180° F).
[G] Product is Certified to NSF/ANSI/CAN 372 and conforms with the lead content requirements
    for "lead free" plumbing as defined by California, Vermont, Maryland, and Louisiana
    state laws and the U.S. Safe Drinking Water Act.