NSF Product and Service Listings

These NSF Official Listings are current as of Saturday, November 23, 2024 at 12:15 a.m. Eastern Time. Please contact NSF to confirm the status of any Listing, report errors, or make suggestions.

Alert: NSF is concerned about fraudulent downloading and manipulation of website text. Always confirm this information by clicking on the below link for the most accurate information: http://info.nsf.org/Certified/Plumbing/Listings.asp?PlantState=PA&

NSF/ANSI 14
Plastics Piping System Components and Related Materials

Click here for a list of End Use Code Designations.

Click on Product Standards or footnote in blue to view the referenced document

Charlotte Pipe & Foundry Company
Plastics Division
4210 Old Charlotte Highway
P.O. Box 1339
Monroe, NC 28111-1339
United States
704-291-3218
Visit this company's website

Facility : Muncy, PA

Drain, Waste, and Vent - Pipe and Fittings

Product Type	Material Type	Trade Name	Product Standard
Pipe§	MLTPL	Charlotte Pipe®	ASTM F1488
1 1/4" - 6" DR 24
§ Product is Certified to the Uniform Plumbing Code™. Installation in accordance with the manufacturer's instructions and the requirements of the latest edition of the Uniform Plumbing Code™.
Pipe §*	PVC	Charlotte Pipe®***	ASTM D2665
1 1/4" - 12" Sch 40
* Socketed and gasketed bell ends are not tested or Listed by NSF for this production facility. § Product is Certified to the Uniform Plumbing Code™. Installation in accordance with the manufacturer's instructions and the requirements of the latest edition of the Uniform Plumbing Code™. *** These pipe products may include the production location code PLPA in the trade name.
Pipe¢ §	ABS	Charlotte Pipe®***	ASTM F628
1 1/4" - 6" Sch 40
¢ Product is authorized to bear the cNSF and/or the cNSFus Mark. § Product is Certified to the Uniform Plumbing Code™. Installation in accordance with the manufacturer's instructions and the requirements of the latest edition of the Uniform Plumbing Code™. *** These pipe products may include the production location code PLPA in the trade name.
Pipe~	ABS	Charlotte Pipe®***	CSA B181.1
1 1/4" - 6" Sch 40
~ Product is authorized to bear the cNSF Mark. *** These pipe products may include the production location code PLPA in the trade name.
Pipe§	PVC	Charlotte Pipe®***	ASTM F891
1 1/2" - 8" Sch 40
10", 12" Sch 40
§ Product is Certified to the Uniform Plumbing Code™. Installation in accordance with the manufacturer's instructions and the requirements of the latest edition of the Uniform Plumbing Code™. *** These pipe products may include the production location code PLPA in the trade name.
Pipe	PVC	Charlotte Pipe®***	ASTM D2949
3 1/4"
*** These pipe products may include the production location code PLPA in the trade name.

Potable Water - Pipe and Fittings

Product Type	Material Type	Trade Name	Product Standard
Pipe + § [G]*	PVC	Charlotte Pipe®***	ASTM D1785
1/2" - 6" Sch 40
1/2" - 8" Sch 80
8" - 12" Sch 40
* Sockets and gasketed bell ends are not tested or Listed by NSF for this production facility. + Material complies with NSF/ANSI/CAN 61 health effects requirements when tested at 73° F. § Product is Certified to the Uniform Plumbing Code™. Installation in accordance with the manufacturer's instructions and the requirements of the latest edition of the Uniform Plumbing Code™. *** These pipe products may include the production location code PLPA in the trade name. [G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state laws and the U.S. Safe Drinking Water Act.
Pipe + § [G]*	PVC	Charlotte Pipe®***	ASTM D2241
1/2" SDR 13.5
3/4" - 2" SDR 21
1" - 6" SDR 26
2 1/2" - 12" SDR 32.5
4" - 12" SDR 41
* Sockets and gasketed bell ends are not tested or Listed by NSF for this production facility. + Material complies with NSF/ANSI/CAN 61 health effects requirements when tested at 73° F. § Product is Certified to the Uniform Plumbing Code™. Installation in accordance with the manufacturer's instructions and the requirements of the latest edition of the Uniform Plumbing Code™. *** These pipe products may include the production location code PLPA in the trade name. [G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state laws and the U.S. Safe Drinking Water Act.

Well Casings

Product Type	Material Type	Trade Name	Product Standard
Well Casings+ [G]	PVC	Charlotte Pipe®***	ASTM F480
2" - 12" Sch 40
+ Material complies with NSF/ANSI/CAN 61 health effects requirements when tested at 73° F. *** These pipe products may include the production location code PLPA in the trade name. [G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state laws and the U.S. Safe Drinking Water Act.

Cresline Plastic Pipe Co., Inc.
600 Cross Pointe Boulevard
Evansville, IN 47715
United States
270-826-8317

Facility : Mechanicsburg, PA

Drain, Waste, and Vent - Pipe and Fittings

Product Type	Material Type	Trade Name	Product Standard
Pipe*	PVC	Cresline® PVC DWV	ASTM D2665
1 1/4" - 8" Sch 40
* Sockets and gasketed bell ends are not tested or Listed by NSF for this production facility.
Pipe*	PVC		ASTM D2665
1 1/4" - 8" Sch 40
* Sockets and gasketed bell ends are not tested or Listed by NSF for this production facility.
Pipe	PVC	Cresline®	ASTM F891
1 1/2" - 8"

Irrigation - Pipe and Fittings

Product Type	Material Type	Trade Name	Product Standard
Pipe	PE 4710	Cresline® HD		ASTM D2239
3/4" - 2" SIDR 15
1" - 2" SIDR 19
Pipe	PE 4710	Cresline® CE Blue®		*SE 30288*
3/4" - 2" SIDR 15
1" - 2" SIDR 19

Potable Water - Pipe and Fittings

Product Type	Material Type	Trade Name	Product Standard
Pipe+ [G]	PE 4710	Cresline® CE Blue®	ASTM D2239
3/4" - 2" SIDR 7
3/4" - 2" SIDR 9
1/2" - 2" SIDR 11.5[1]
[1] These pipe sizes are not certified for use in potable water applications containing oxidizing disinfectants and shall not be marked with a CC oxidative resistance classification. + Material complies with NSF/ANSI/CAN 61 health effects requirements when tested at 73° F. [G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state laws and the U.S. Safe Drinking Water Act.
Tubing+ [G]	PE 4710	Cresline® CE Blue®	ASTM D2737
3/4" - 2" SIDR 9
+ Material complies with NSF/ANSI/CAN 61 health effects requirements when tested at 73° F. [G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state laws and the U.S. Safe Drinking Water Act.
Tubing+ [G]	PE 4710	Cresline® CE Blue®	AWWA C901
3/4" - 2" SIDR 9
+ Material complies with NSF/ANSI/CAN 61 health effects requirements when tested at 73° F. [G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state laws and the U.S. Safe Drinking Water Act.
Pipe+ [G]	PE 4710	Cresline® HD	ASTM D2239
3/4" - 2" SIDR 7
3/4" - 2" SIDR 9
1/2" - 2" SIDR 11.5[1]
[1] These pipe sizes are not certified for use in potable water applications containing oxidizing disinfectants and shall not be marked with a CC oxidative resistance classification. + Material complies with NSF/ANSI/CAN 61 health effects requirements when tested at 73° F. [G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state laws and the U.S. Safe Drinking Water Act.
Tubing+ [G]	PE 4710	Cresline® HD-CTS	ASTM D2737
3/4" - 2" SDR 9
+ Material complies with NSF/ANSI/CAN 61 health effects requirements when tested at 73° F. [G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state laws and the U.S. Safe Drinking Water Act.
Tubing+ [G]	PE 4710	Cresline® HD-CTS	AWWA C901
3/4" - 2" SDR 9
+ Material complies with NSF/ANSI/CAN 61 health effects requirements when tested at 73° F. [G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state laws and the U.S. Safe Drinking Water Act.
Pipe + [G]*	PVC	Cresline® PVC	ASTM D1785
1/2" - 8" Sch 40
1/2" - 8" Sch 80
* Sockets and gasketed bell ends are not tested or Listed by NSF for this production facility. + Material complies with NSF/ANSI/CAN 61 health effects requirements when tested at 73° F. [G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state laws and the U.S. Safe Drinking Water Act.
Pipe + [G]*	PVC		ASTM D1785
1/2" - 8" Sch 40
1/2" - 8" Sch 80
* Sockets and gasketed bell ends are not tested or Listed by NSF for this production facility. + Material complies with NSF/ANSI/CAN 61 health effects requirements when tested at 73° F. [G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state laws and the U.S. Safe Drinking Water Act.
Pipe + [G]*	PVC	Cresline® PVC	ASTM D2241
1/2" - 8" SDR 13.5
1/2" - 8" SDR 26
1/2" - 8" SDR 21
5" SDR 17
* Sockets and gasketed bell ends are not tested or Listed by NSF for this production facility. + Material complies with NSF/ANSI/CAN 61 health effects requirements when tested at 73° F. [G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state laws and the U.S. Safe Drinking Water Act.
Pipe + [G]*	PVC		ASTM D2241
1/2" - 8" SDR 13.5
1/2" - 8" SDR 26
1/2" - 8" SDR 21
5" SDR 17
* Sockets and gasketed bell ends are not tested or Listed by NSF for this production facility. + Material complies with NSF/ANSI/CAN 61 health effects requirements when tested at 73° F. [G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state laws and the U.S. Safe Drinking Water Act.

Well Casings

Product Type	Material Type	Trade Name	Product Standard
Well Casings[G]	PVC	Cresline®	ASTM F480
4" - 8" SDR 26
4" - 8" SDR 21
4 1/2" - 6" SDR 17
2" - 8" Sch 40
6 1/4" DR 27.6
4 1/2" DR 20
[G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state laws and the U.S. Safe Drinking Water Act.

Georg Fischer Central Plastics LLC
4949 Joseph Hardin Drive
Dallas, TX 75236
United States
469-801-2246

Facility : Titusville, PA

Gas Applications - Pipe and Fittings

Product Type	Material Type	Trade Name	Product Standard
Pipe*	PE 2708	+GF+ DESIGN FLOW	ASTM D2513
1/2" CTS - .090 WALL
3/4" CTS - .090 WALL
1 1/8" CTS - .099 WALL, 0.090 WALL
1/2" IPS SDR 9.3
3/4" IPS SDR 11
1" IPS SDR 11
1 1/4" IPS SDR 10, 11
1 1/2" IPS SDR 11
2" IPS SDR 11
3" IPS SDR 11, 11.5
4" IPS SDR 11, 11.5, 13.5
* Product is authorized to bear the cNSF Mark.
Pipe*	PE 4710	+GF+ DESIGN FLOW	ASTM D2513
1/2" CTS - .090 WALL, .062 WALL
3/4" CTS - .090 WALL
1" CTS -.121, .101, .101, .099, .090 WALL
1 1/4" CTS - .090 WALL
3/4" IPS SDR 7.3, 9, 11
1" IPS SDR 7.3, 9, 11
1 1/4" IPS SDR 7.3, 9, 11
1 1/2" IPS SDR 7.3, 9, 11
2" IPS SDR 7.3, 9, 11, 13.5, 15.5, 17
3" IPS SDR 7.3, 9, 11, 13.5, 15.5, 17
4" IPS SDR 7.3, 9, 11, 13.5, 15.5, 17
6" IPS SDR 9, 11, 13.5, 15.5, 17
8" IPS SDR 11, 13.5, 15.5, 17
10" IPS SDR 13.5, 15.5, 17
12" IPS SDR 15.5, 17
* Product is authorized to bear the cNSF Mark.

Potable Water - Pipe and Fittings

Product Type	Material Type	Trade Name	Product Standard
Pipe$ + [G]	PE 4710	+GF+ DESIGN FLOW	ASTM D2239
3/4" - 2" SIDR 5.3
3/4" - 2" SIDR 7
3/4" - 2" SIDR 9
1/2" - 3" SIDR 11.5[1]
3/4" - 3" SIDR 15[1]
1/2" - 2" SIDR 19[1]
[1] These pipe sizes are not certified for use in potable water applications containing oxidizing disinfectants and shall not be marked with a CC oxidative resistance classification. $ These products also meet the requirements for PE 3408 per ASTM D3350-02a. + Material complies with NSF/ANSI/CAN 61 health effects requirements when tested at 73° F. [G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state laws and the U.S. Safe Drinking Water Act.
Pipe+ [G]	PE 4710	+GF+ DESIGN FLOW	ASTM D2737
3/4" - 2" SDR 9
+ Material complies with NSF/ANSI/CAN 61 health effects requirements when tested at 73° F. [G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state laws and the U.S. Safe Drinking Water Act.
Pipe$ + [G]	PE 4710	+GF+ DESIGN FLOW	ASTM D3035
1/2" DR 7[1]
3/4" - 3" DR 7
1/2" DR 9[1]
3/4" - 3" DR 9
1/2" - 3" DR 11[1]
1/2" - 3" DR 13.5[1]
3/4" - 3" DR 15.5[1]
3/4" - 3" DR 17[1]
1" - 3" DR 21[1]
1" - 3" DR 26[1]
1 1/2" - 3" DR 32.5[1]
[1] These pipe sizes are not certified for use in potable water applications containing oxidizing disinfectants and shall not be marked with a CC oxidative resistance classification. $ These products also meet the requirements for PE 3408 per ASTM D3350-02a. + Material complies with NSF/ANSI/CAN 61 health effects requirements when tested at 73° F. [G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state laws and the U.S. Safe Drinking Water Act.
Pipe$ + [G]	PE 4710	+GF+ DESIGN FLOW	ASTM F714
4" - 18" IPS DR 7.3
4" - 26" IPS DR 7
4" - 36" IPS DR 9
4" - 42" IPS DR 11
4" - 48" IPS DR 13.5
4" - 54" IPS DR 15.5[2]
4" - 54" IPS DR 17
4" - 54" IPS DR 21
4" - 54" IPS DR 26
4" - 54" IPS DR 32.5
4" - 54" IPS DR 41
[2] Special sizes may be acceptable for engineered applications, due to system conditions or special local requirements. It is the responsibility of the end user to ensure that the product is suitable for the intended application. $ These products also meet the requirements for PE 3408 per ASTM D3350-02a. + Material complies with NSF/ANSI/CAN 61 health effects requirements when tested at 73° F. [G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state laws and the U.S. Safe Drinking Water Act.
Pipe+ [G]	PE 4710	+GF+ DESIGN FLOW	AWWA C901
3/4" - 3" SDR 9
+ Material complies with NSF/ANSI/CAN 61 health effects requirements when tested at 73° F. [G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state laws and the U.S. Safe Drinking Water Act.
Pipe$ + [G]*	PE 4710	+GF+ DESIGN FLOW	AWWA C906
4" - 26" IPS DR 7
4" - 28" IPS DR 7.3[2]
4" - 34" IPS DR 9
4" - 42" IPS DR 11
4" - 48" IPS DR 13.5
4" - 54" IPS DR 15.5[2]
4" - 54" IPS DR 17
4" - 54" IPS DR 21
4" - 54" IPS DR 26[2]
4" - 54" IPS DR 32.5[2]
[2] Special sizes may be acceptable for engineered applications, due to system conditions or special local requirements. It is the responsibility of the end user to ensure that the product is suitable for the intended application. $ These products also meet the requirements for PE 3408 per ASTM D3350-02a. * These products also meet the requirements for PE 3408 per ASTM D3350-02a. + Material complies with NSF/ANSI/CAN 61 health effects requirements when tested at 73° F. [G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state laws and the U.S. Safe Drinking Water Act.

NOTE: Only products bearing the NSF Mark on the product, product packaging, and/or
      documentation shipped with the product are Certified.

Georg Fischer LLC
9271 Jeronimo Road
Irvine, CA 92618
United States
610-252-7355
Visit this company's website

Facility : Easton, PA

Drain, Waste, and Vent - Pipe and Fittings

Product Type	Material Type	Trade Name	Product Standard
Pipe*	PVC	+GF+ Harvel® Industrial	ASTM D2665
1 1/4" - 24" Sch 40
* Sockets and gasketed bell ends are not tested or Listed by NSF International for this production facility.
Pipe*	PVC	+GF+ Harvel® Industrial PLUS	ASTM D2665
1 1/4" - 24" Sch 40
* Sockets and gasketed bell ends are not tested or Listed by NSF International for this production facility.

Potable Water - Pipe and Fittings

Product Type	Material Type	Trade Name	Product Standard
Pipe + [G]*	PVC	+GF+ Harvel® Industrial	ASTM D1785
1/8" - 24" Sch 40
1/8" - 24" Sch 80
* Sockets and gasketed bell ends are not tested or Listed by NSF International for this production facility. + Material complies with NSF/ANSI/CAN 61 health effects requirements when tested at 73° F. [G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state laws and the U.S. Safe Drinking Water Act.
Pipe + [G]*	PVC	+GF+ Harvel® Industrial PLUS	ASTM D1785
1/8" - 24" Sch 40
1/8" - 24" Sch 80
* Sockets and gasketed bell ends are not tested or Listed by NSF International for this production facility. + Material complies with NSF/ANSI/CAN 61 health effects requirements when tested at 73° F. [G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state laws and the U.S. Safe Drinking Water Act.
Pipe + [G]*	PVC	+GF+ HARVEL PVC	ASTM D1785
1/8" - 24" Sch 40
1/8" - 24" Sch 80
1/2" - 8" Sch 120
* Sockets and gasketed bell ends are not tested or Listed by NSF International for this production facility. + Material complies with NSF/ANSI/CAN 61 health effects requirements when tested at 73° F. [G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state laws and the U.S. Safe Drinking Water Act.
Pipe + [G]*	PVC		ASTM D1785
1/2" - 8" Sch 120
* Sockets and gasketed bell ends are not tested or Listed by NSF International for this production facility. + Material complies with NSF/ANSI/CAN 61 health effects requirements when tested at 73° F. [G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state laws and the U.S. Safe Drinking Water Act.
Pipe + [G]*	PVC	+GF+ HARVEL PVC	ASTM D2241
1/2" SDR 13.5
3/4" - 10" SDR 21
1"- 24" SDR 26
18" SDR 41
20" SDR 41
24" SDR 41
* Sockets and gasketed bell ends are not tested or Listed by NSF International for this production facility. + Material complies with NSF/ANSI/CAN 61 health effects requirements when tested at 73° F. [G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state laws and the U.S. Safe Drinking Water Act.
Pipe + [G]*	PVC		ASTM D2241
1/2" SDR 13.5
3/4" - 10" SDR 21
1" - 24" SDR 26
18" SDR 41
20" SDR 41
24" SDR 41
* Sockets and gasketed bell ends are not tested or Listed by NSF International for this production facility. + Material complies with NSF/ANSI/CAN 61 health effects requirements when tested at 73° F. [G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state laws and the U.S. Safe Drinking Water Act.
Pipe+ ¢ [G]	PVC	+GF+ Harvel® Industrial	CSA B137.3
1/2" - 24" Sch 80
1/2" - 20" Sch 40
+ Material complies with NSF/ANSI/CAN 61 health effects requirements when tested at 73° F. ¢ Product is authorized to bear the cNSF and/or the cNSFus Mark. [G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state laws and the U.S. Safe Drinking Water Act.
Pipe+ ¢ [G]	PVC	+GF+ Harvel® Industrial PLUS	CSA B137.3
1/2" - 20" Sch 40
1/2" - 24" Sch 80
+ Material complies with NSF/ANSI/CAN 61 health effects requirements when tested at 73° F. ¢ Product is authorized to bear the cNSF and/or the cNSFus Mark. [G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state laws and the U.S. Safe Drinking Water Act.
Pipe+ ¢ [G]	PVC	+GF+ HARVEL PVC	CSA B137.3
1/2" - 24" Sch 40
1/2" - 24" Sch 80
+ Material complies with NSF/ANSI/CAN 61 health effects requirements when tested at 73° F. ¢ Product is authorized to bear the cNSF and/or the cNSFus Mark. [G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state laws and the U.S. Safe Drinking Water Act.
Pipe+ ¢ [G]	PVC		CSA B137.3
1/2" - 24" Sch 40
1/2" - 24" Sch 80
+ Material complies with NSF/ANSI/CAN 61 health effects requirements when tested at 73° F. ¢ Product is authorized to bear the cNSF and/or the cNSFus Mark. [G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state laws and the U.S. Safe Drinking Water Act.
Pipe¢ +++ [G]	CPVC 4120	+GF+ HydroKing Commercial	ASTM F442
2 1/2" - 8" SDR 11
¢ Product is authorized to bear the cNSF and/or the cNSFus Mark. +++ Material complies with NSF/ANSI/CAN 61 health effects requirements when tested at temperatures up to and including Commercial Hot (180° F). [G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state laws and the U.S. Safe Drinking Water Act.
Pipe¢ +++ [G]	CPVC 4120	+GF+ HydroKing Commercial	CSA B137.6
1 1/4" - 2 1/2" Sch 80
2 1/2" - 4" SDR 11
¢ Product is authorized to bear the cNSF and/or the cNSFus Mark. +++ Material complies with NSF/ANSI/CAN 61 health effects requirements when tested at temperatures up to and including Commercial Hot (180° F). [G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state laws and the U.S. Safe Drinking Water Act.
Pipe+++ [G]	CPVC 4120	ChlorFIT®	ASTM F441
1/4" - 24" Sch 40
1/4" - 24" Sch 80
+++ Material complies with NSF/ANSI/CAN 61 health effects requirements when tested at temperatures up to and including Commercial Hot (180° F). [G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state laws and the U.S. Safe Drinking Water Act.
Pipe+++ [G]	CPVC 4120	+GF+ HARVEL CPVC	ASTM F441
1/4" - 24" Sch 40
1/4" - 24" Sch 80
+++ Material complies with NSF/ANSI/CAN 61 health effects requirements when tested at temperatures up to and including Commercial Hot (180° F). [G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state laws and the U.S. Safe Drinking Water Act.
Pipe+++ [G]	CPVC 4120		ASTM F441
1/4" - 24" Sch 40
1/4" - 24" Sch 80
+++ Material complies with NSF/ANSI/CAN 61 health effects requirements when tested at temperatures up to and including Commercial Hot (180° F). [G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state laws and the U.S. Safe Drinking Water Act.
Pipe+++ [G]	CPVC 4120	SeaCor®	ASTM F441
1/4" - 24" Sch 40
1/4" - 24" Sch 80
+++ Material complies with NSF/ANSI/CAN 61 health effects requirements when tested at temperatures up to and including Commercial Hot (180° F). [G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state laws and the U.S. Safe Drinking Water Act.
Pipe+++ [G]	CPVC 4120		ASTM F442
3/4" - 3" SDR 13.5
+++ Material complies with NSF/ANSI/CAN 61 health effects requirements when tested at temperatures up to and including Commercial Hot (180° F). [G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state laws and the U.S. Safe Drinking Water Act.
Pipe¢ +++ [G]	CPVC 4120	ChlorFIT®	CSA B137.6
3/8" - 2" SDR 11
1 1/4" - 2 1/2" Sch 80
¢ Product is authorized to bear the cNSF and/or the cNSFus Mark. +++ Material complies with NSF/ANSI/CAN 61 health effects requirements when tested at temperatures up to and including Commercial Hot (180° F). [G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state laws and the U.S. Safe Drinking Water Act.
Pipe¢ +++ [G]	CPVC 4120	+GF+ HARVEL CPVC	CSA B137.6
3/8" - 2" SDR 11
1 1/4" - 2 1/2" Sch 80
¢ Product is authorized to bear the cNSF and/or the cNSFus Mark. +++ Material complies with NSF/ANSI/CAN 61 health effects requirements when tested at temperatures up to and including Commercial Hot (180° F). [G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state laws and the U.S. Safe Drinking Water Act.
Pipe¢ +++ [G]	CPVC 4120		CSA B137.6
3/8" - 2" SDR 11
1 1/4" - 2 1/2" Sch 80
¢ Product is authorized to bear the cNSF and/or the cNSFus Mark. +++ Material complies with NSF/ANSI/CAN 61 health effects requirements when tested at temperatures up to and including Commercial Hot (180° F). [G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state laws and the U.S. Safe Drinking Water Act.
Pipe¢ +++ [G]	CPVC 4120	SeaCor®	CSA B137.6
3/8" - 2" SDR 11
1 1/4" - 2 1/2" Sch 80
¢ Product is authorized to bear the cNSF and/or the cNSFus Mark. +++ Material complies with NSF/ANSI/CAN 61 health effects requirements when tested at temperatures up to and including Commercial Hot (180° F). [G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state laws and the U.S. Safe Drinking Water Act.

Well Casings

Product Type	Material Type	Trade Name	Product Standard
Well Casings* [G]*	PVC	HARVEL PVC	ASTM F480
2" - 16" Sch 40
2" - 16" Sch 80
2" - 16" SDR 17
2" - 10" SDR 21
4" - 16" SDR 26
** Sockets and gasketed bell-ends are not tested or Certified by NSF International for this production facility. [G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state laws and the U.S. Safe Drinking Water Act.
Well Casings* [G]*	PVC		ASTM F480
2" - 16" Sch 40
2" - 16" Sch 80
2" - 16" SDR 17
2" - 10" SDR 21
4" - 16" SDR 26
** Sockets and gasketed bell-ends are not tested or Certified by NSF International for this production facility. [G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state laws and the U.S. Safe Drinking Water Act.

J-M Manufacturing Co., Inc. DBA JM Eagle
9 Peach Tree Hill Road
Livingston, NJ 07039
United States
310-693-8200
Visit this company's website

Facility : # 11 Cochranton, PA

Drain, Waste, and Vent - Pipe and Fittings

Product Type	Material Type	Trade Name	Product Standard
Pipe# §	PVC	J-M Manufacturing	ASTM D2665
1 1/4" - 16" Sch 40
# This product may be marked with an alternate trade name: J-M Manufacturing and/or PW Eagle and/or [JMM Logo] and/or JM Eagle and/or [JM Eagle Logo]. § Product is Certified to the Uniform Plumbing Code™. Installation in accordance with the manufacturer's instructions and the requirements of the latest edition of the Uniform Plumbing Code™.
Pipe# §	PVC	J-M Manufacturing	ASTM F891
1 1/4" - 8" Sch 40
# This product may be marked with an alternate trade name: J-M Manufacturing and/or PW Eagle and/or [JMM Logo] and/or JM Eagle and/or [JM Eagle Logo]. § Product is Certified to the Uniform Plumbing Code™. Installation in accordance with the manufacturer's instructions and the requirements of the latest edition of the Uniform Plumbing Code™.

NOTE: Only products bearing the NSF Mark are Certified.

Electrical Conduit and Accessories

Product Type	Material Type	Trade Name	Product Standard
PVC Foam Core Conduit#	PVC	J-M Manufacturing	UL 651
3", 4", 6" Sch 40
# This product may be marked with an alternate trade name: J-M Manufacturing and/or PW Eagle and/or [JMM Logo] and/or JM Eagle and/or [JM Eagle Logo].
Rigid Conduit#	PVC	J-M Manufacturing	CSA C22.2 No. 211.1
2", 3", 3.5", 4", 5", 6" Type DB2/ES2
# This product may be marked with an alternate trade name: J-M Manufacturing and/or PW Eagle and/or [JMM Logo] and/or JM Eagle and/or [JM Eagle Logo].
Rigid Conduit#	PVC	J-M Manufacturing	CSA C22.2 No. 211.2
0.5", 0.75", 1", 1.25", 1.5", 2" Sch 40
3", 4", 5", 6", 8" Sch 40
# This product may be marked with an alternate trade name: J-M Manufacturing and/or PW Eagle and/or [JMM Logo] and/or JM Eagle and/or [JM Eagle Logo].

* Complies with requirements for above ground, underground or indoor use; sunlight
  resistance and use with maximum 90°C wire.
NOTE: Only products bearing the NSF Mark are Certified.

Gas Applications - Pipe and Fittings

Product Type	Material Type	Trade Name	Product Standard
Pipe §*	PE 2708	JM Eagle	ASTM D2513
1/2" CTS SDR 7
3/4" CTS SDR 9.8
1" CTS SDR 9.3
1" CTS SDR 11.5
1" CTS SDR 12.5
1 1/4" CTS SDR 11.5
1 1/4" CTS SDR 15.3
1/2" IPS SDR 9.3
1/2" IPS SDR 11
3/4" IPS SDR 9.3
3/4" IPS SDR 11
1" IPS SDR 11
1 1/4" IPS SDR 10
1 1/4" IPS SDR 11
1 1/2" IPS SDR 11
2" IPS SDR 11
2" IPS SDR 11.5
3" IPS SDR 11
3" IPS SDR 11.5
3" IPS SDR 13.5
3" IPS SDR 17
4" IPS SDR 11
4" IPS SDR 11.5
4" IPS SDR 13.5
4" IPS SDR 17
6" IPS SDR 11
6" IPS SDR 11.5
6" IPS SDR 13.5
6" IPS SDR 17
8" IPS SDR 11
8" IPS SDR 11.5
8" IPS SDR 13.5
10" IPS SDR 13.5
10" IPS SDR 15.5
10" IPS SDR 17
12" IPS SDR 11
12" IPS SDR 11.5
12" IPS SDR 13.5
12" IPS SDR 17
* Gas pipe and tubing limited to outside underground use only. § Product is Certified to the Uniform Plumbing Code™. Installation in accordance with the manufacturer's instructions and the requirements of the latest edition of the Uniform Plumbing Code™.

NOTE: Only products bearing the NSF Mark are Certified.

Oil and Gas Producing Applications - Pipe and Fittings

Product Type	Material Type	Trade Name	Product Standard
Pipe^	PE 4710	J-M Manufacturing	ASTM F2619
1/2" - 24" SDR 7
1/2" - 24" SDR 7.3
1/2" - 30" SDR 9
1/2" - 36" SDR 11
1/2" - 42" SDR 13.5
2" - 54" SDR 17
3" - 63" SDR 21
6" - 63" SDR 26
6" - 63" SDR 32.5
^ This product may be marked with an alternate trade name: JM Eagle or [JM Eagle Logo].

Potable Water - Pipe and Fittings

Product Type	Material Type	Trade Name	Product Standard
Pipe+ ^ § [3] [G]	PE 4710	J-M Manufacturing	AWWA C906
4" - 65"
+ Material complies with NSF/ANSI/CAN 61 health effects requirements when tested at 73° F. ^ This product may be marked with an alternate trade name: JM Eagle, [JM Eagle Logo], [JMM Logo], JM Eagle Poly-Flo, JM Eagle-Tough Turf Irrigation Pipe, JM Eagle Geo-Flo, and/or JM Eagle-Tough Turf Mainline. § Product is Certified to the Uniform Plumbing Code™. Installation in accordance with the manufacturer's instructions and the requirements of the latest edition of the Uniform Plumbing Code™. [3] Special sizes may be acceptable for engineered applications, due to system conditions or special local requirements. It is the responsibility of the end user to ensure that the product is suitable for the intended application. [G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state laws and the U.S. Safe Drinking Water Act.
Pipe+ ^ § [G]	PE 4710	J-M Manufacturing	ASTM F714
IPS 4" - 65"[3]
[3] Special sizes may be acceptable for engineered applications, due to system conditions or special local requirements. It is the responsibility of the end user to ensure that the product is suitable for the intended application. + Material complies with NSF/ANSI/CAN 61 health effects requirements when tested at 73° F. ^ This product may be marked with an alternate trade name: JM Eagle, [JM Eagle Logo], [JMM Logo], JM Eagle Poly-Flo, JM Eagle-Tough Turf Irrigation Pipe, JM Eagle Geo-Flo, and/or JM Eagle-Tough Turf Mainline. § Product is Certified to the Uniform Plumbing Code™. Installation in accordance with the manufacturer's instructions and the requirements of the latest edition of the Uniform Plumbing Code™. [G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state laws and the U.S. Safe Drinking Water Act.
Pipe+ ^ § [G]	PE 4710	J-M Manufacturing	ASTM D2737
3/4" - 2" SDR 9
3/4" - 2" SDR 7.3
+ Material complies with NSF/ANSI/CAN 61 health effects requirements when tested at 73° F. ^ This product may be marked with an alternate trade name: JM Eagle, [JM Eagle Logo], [JMM Logo], JM Eagle Poly-Flo, JM Eagle-Tough Turf Irrigation Pipe, JM Eagle Geo-Flo, and/or JM Eagle-Tough Turf Mainline. § Product is Certified to the Uniform Plumbing Code™. Installation in accordance with the manufacturer's instructions and the requirements of the latest edition of the Uniform Plumbing Code™. [G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state laws and the U.S. Safe Drinking Water Act.
Pipe+ ^ § [G]	PE 4710	J-M Manufacturing	ASTM D3035
3/4" - 3" DR 7
3/4" - 3" DR 9
1/2" - 3" DR 11[1]
1/2" - 3" DR 13.5[1]
1/2" DR 17[1] [2]
3/4" - 3" DR 17[1]
1/2" - 3/4" DR 21[1] [2]
1" - 3" DR 21[1]
1/2" - 3/4" DR 26[1] [2]
1" - 3" DR 26[1]
[1] Gasketed bell end pipe [1] Gasketed bell end pipe [2] Solvent bell end pipe + Material complies with NSF/ANSI/CAN 61 health effects requirements when tested at 73° F. ^ This product may be marked with an alternate trade name: JM Eagle, [JM Eagle Logo], [JMM Logo], JM Eagle Poly-Flo, JM Eagle-Tough Turf Irrigation Pipe, JM Eagle Geo-Flo, and/or JM Eagle-Tough Turf Mainline. § Product is Certified to the Uniform Plumbing Code™. Installation in accordance with the manufacturer's instructions and the requirements of the latest edition of the Uniform Plumbing Code™. [G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state laws and the U.S. Safe Drinking Water Act.
Pipe+ ^ § [G]	PE 4710	J-M Manufacturing	AWWA C901
3/4" - 3" SDR 9
+ Material complies with NSF/ANSI/CAN 61 health effects requirements when tested at 73° F. ^ This product may be marked with an alternate trade name: JM Eagle, [JM Eagle Logo], [JMM Logo], JM Eagle Poly-Flo, JM Eagle-Tough Turf Irrigation Pipe, JM Eagle Geo-Flo, and/or JM Eagle-Tough Turf Mainline. § Product is Certified to the Uniform Plumbing Code™. Installation in accordance with the manufacturer's instructions and the requirements of the latest edition of the Uniform Plumbing Code™. [G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state laws and the U.S. Safe Drinking Water Act.
Pipe# + [G]	PVC	J-M Manufacturing	AWWA C900
14" - 48"
# This product may be marked with an alternate trade name: J-M Manufacturing and/or PW Eagle and/or [JMM Logo] and/or JM Eagle and/or [JM Eagle Logo]. + Material complies with NSF/ANSI/CAN 61 health effects requirements when tested at 73° F. [G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state laws and the U.S. Safe Drinking Water Act.
Pipe# + § [G]*	PVC	J-M Manufacturing	ASTM D2241
1/2" - 6" SDR 13.5
3/4" - 12" SDR 17
3/4" - 12" SDR 21
1" - 12" SDR 26
1 1/4" - 12" SDR 32.5
# This product may be marked with an alternate trade name: J-M Manufacturing and/or PW Eagle and/or [JMM Logo] and/or JM Eagle and/or [JM Eagle Logo]. * Sockets and gasketed bell ends are not tested or Listed by NSF for this production facility. + Material complies with NSF/ANSI/CAN 61 health effects requirements when tested at 73° F. § Product is Certified to the Uniform Plumbing Code™. Installation in accordance with the manufacturer's instructions and the requirements of the latest edition of the Uniform Plumbing Code™. [G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state laws and the U.S. Safe Drinking Water Act.
Pipe# + § [G]*	PVC	J-M Manufacturing	ASTM D1785
1/2" - 12" Sch 40
1/2" - 12" Sch 80
# This product may be marked with an alternate trade name: J-M Manufacturing and/or PW Eagle and/or [JMM Logo] and/or JM Eagle and/or [JM Eagle Logo]. * Sockets and gasketed bell ends are not tested or Listed by NSF for this production facility. + Material complies with NSF/ANSI/CAN 61 health effects requirements when tested at 73° F. § Product is Certified to the Uniform Plumbing Code™. Installation in accordance with the manufacturer's instructions and the requirements of the latest edition of the Uniform Plumbing Code™. [G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state laws and the U.S. Safe Drinking Water Act.
Pipe# + ¢ [G]	PVC	J-M Manufacturing	CSA B137.3
4" - 24" CIOD DR 14[1]
4" - 24" CIOD DR 18[1]
4" - 24" CIOD DR 25[1]
1/2" - 8" Sch 40[2]
1/2" - 8" IPS DR 32.5[2]
[1] Gasketed bell end pipe [2] Solvent bell end pipe # This product may be marked with an alternate trade name: J-M Manufacturing and/or PW Eagle and/or [JMM Logo] and/or JM Eagle and/or [JM Eagle Logo]. + Material complies with NSF/ANSI/CAN 61 health effects requirements when tested at 73° F. ¢ Product is authorized to bear the cNSF and/or the cNSFus Mark. [G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state laws and the U.S. Safe Drinking Water Act.

NOTE: Only products bearing the NSF Mark are Certified.

Reclaimed Water - Pipe and Fittings

Product Type	Material Type	Trade Name	Product Standard
Pipe#	PVC	J-M Manufacturing	AWWA C900
14" - 48"
# This product may be marked with an alternate trade name: PW Eagle and/or (JMM Logo) and/or JM Eagle and/or (JM Eagle Logo).
Pipe^	PE 4710	J-M Manufacturing	AWWA C906
4" - 65"
^ This product may be marked with an alternate trade name: JM Eagle, [JM Eagle Logo], [JMM Logo], JM Eagle Poly-Flo, JM Eagle-Tough Turf Irrigation Pipe, JM Eagle Geo-Flo, and/or JM Eagle-Tough Turf Mainline.
Pipe^	PE 4710	J-M Manufacturing	ASTM F714
4" - 65"
^ This product may be marked with an alternate trade name: JM Eagle, [JM Eagle Logo], [JMM Logo], JM Eagle Poly-Flo, JM Eagle-Tough Turf Irrigation Pipe, JM Eagle Geo-Flo, and/or JM Eagle-Tough Turf Mainline.

NOTE: Only products bearing the NSF Mark are Certified.

Sewer Main - Pipe and Fittings

Product Type	Material Type	Trade Name	Product Standard
Pipe#	PVC	J-M Manufacturing	AWWA C900
14" - 48"
# This product may be marked with an alternate trade name: J-M Manufacturing and/or PW Eagle and/or [JMM Logo] and/or JM Eagle and/or [JM Eagle Logo].
Pipe^	PE 4710	J-M Manufacturing	AWWA C906
4" - 65"
^ This product may be marked with an alternate trade name: JM Eagle, [JM Eagle Logo], [JMM Logo], JM Eagle Poly-Flo, JM Eagle-Tough Turf Irrigation Pipe, JM Eagle Geo-Flo, and/or JM Eagle-Tough Turf Mainline.
Pipe^	PE 4710	J-M Manufacturing	ASTM F714
4" - 65"
^ This product may be marked with an alternate trade name: JM Eagle, [JM Eagle Logo], [JMM Logo], JM Eagle Poly-Flo, JM Eagle-Tough Turf Irrigation Pipe, JM Eagle Geo-Flo, and/or JM Eagle-Tough Turf Mainline.
Pipe# ¢	PVC	J-M Manufacturing	CSA B182.2
4" - 24" DR 26[1]
4" - 24" DR 35[1]
4", 6" DR 26[2]
4", 6" DR 35[2]
[1] Gasketed bell end pipe [2] Solvent bell end pipe # This product may be marked with an alternate trade name: J-M Manufacturing and/or PW Eagle and/or [JMM Logo] and/or JM Eagle and/or [JM Eagle Logo]. ¢ Product is authorized to bear the cNSF and/or the cNSFus Mark.

NOTE: Only products bearing the NSF Mark are Certified.

Oil Creek Plastics
East Titusville Road
P.O. Box 385
Titusville, PA 16354
United States
800-537-3661
814-827-3661
Visit this company's website

Facility : Titusville, PA

Gas Applications - Pipe and Fittings

Product Type	Material Type	Trade Name	Product Standard
Pipe §*	PE 2708	OIL CREEK PLASTICS	ASTM D2513
1/2" CTS X .090" WALL
1/2" IPS DR 9.3
3/4", 1", 1 1/4", 1 1/2", 2", 3", 4", 6" IPS DR 11
1" CTS X .099" WALL
1 1/4" IPS DR 10
3", 4" IPS DR 11.5
6" IPS DR 13.5
* Gas pipe and tubing limited to outside underground use only. § Product is Certified to the Uniform Plumbing Code™. Installation in accordance with the manufacturer's instructions and the requirements of the latest edition of the Uniform Plumbing Code™.
Pipe §*	PE 4710	OIL CREEK PLASTICS	ASTM D2513
1/2" IPS DR 9.33
3/4" , 1" , 1-1/4" , 1-1/2" , 2" , 3" , 4" IPS DR 11
1/2" CTS x .090" wall
1" CTS x .099" wall
1" CTS x .101" wall
1-1/4" CTS x .121" wall
* Gas pipe and tubing limited to outside underground use only. § Product is Certified to the Uniform Plumbing Code™. Installation in accordance with the manufacturer's instructions and the requirements of the latest edition of the Uniform Plumbing Code™.

Potable Water - Pipe and Fittings

Product Type	Material Type	Trade Name	Product Standard
Pipe$ +	PE 3608/4710	Oil Creek Aqua-Jet	ASTM D2239
3/4" - 2" SIDR 5.3
3/4" - 2" SIDR 7
3/4" - 2" SIDR 9
1/2" - 2" SIDR 11.5[2]
3/4" - 3" SIDR 15[2]
3/4" - 2" SIDR 19[2]
[2] These pipe sizes shall not be marked with a CC oxidative resistance classification and are not certified for use in applications where an oxidative resistance classification (e.g. CC1, CC2, CC3), in accordance with ASTM D3350, is required. $ These products also meet the requirements for PE 3408 per ASTM D3350-02a. + Material complies with NSF/ANSI/CAN 61 health effects requirements when tested at 73° F.
Pipe$ +	PE 3608/4710		ASTM D2239
3/4" - 2" SIDR 5.3
3/4" - 2" SIDR 7
3/4" - 2" SIDR 9
1/2" - 2" SIDR 11.5[2]
3/4" - 3" SIDR 15[2]
3/4" - 2" SIDR 19[2]
[2] These pipe sizes shall not be marked with a CC oxidative resistance classification and are not certified for use in applications where an oxidative resistance classification (e.g. CC1, CC2, CC3), in accordance with ASTM D3350, is required. $ These products also meet the requirements for PE 3408 per ASTM D3350-02a. + Material complies with NSF/ANSI/CAN 61 health effects requirements when tested at 73° F.
Tubing# ^ § +++ [4]	PE-RT 4710	AQUA-PERT	ASTM F2769
1/8" - 6" SDR 9
# Certified AQUA-PERT is coextruded natural tubing with a red, blue, or white outer layer. ^ Meets the chlorine resistance requirements of ASTM F2769 when tested in accordance with ASTM F2023. § Product is Certified to the Uniform Plumbing Code™. Installation in accordance with the manufacturer's instructions and the requirements of the latest edition of the Uniform Plumbing Code™. +++ Material complies with NSF/ANSI/CAN 61 health effects requirements when tested at temperatures up to and including Commercial Hot (180° F). [4] Tubing certified against ASTM F2769 and CSA B137.18 shall include the standard designation(s) of the fitting system(s) for which the tubing is recommended by the manufacturer, and shall be marked, as applicable, with the following fitting system designation(s): ASTM F1807, ASTM F2159 and ASTM F1960.
Tubing# ^ ¢ § +++ [1] [4]	PE-RT 4710	AQUA-PERT	CSA B137.18
1/8" - 6" SDR 9
# Certified AQUA-PERT is coextruded natural tubing with a red, blue, or white outer layer. ^ Meets the chlorine resistance requirements of ASTM F2769 when tested in accordance with ASTM F2023. ¢ Product is authorized to bear the cNSF and/or the cNSFus Mark. § Product is Certified to the Uniform Plumbing Code™. Installation in accordance with the manufacturer's instructions and the requirements of the latest edition of the Uniform Plumbing Code™. +++ Material complies with NSF/ANSI/CAN 61 health effects requirements when tested at temperatures up to and including Commercial Hot (180° F). [1] Tubing certified against CSA B137.18 shall include the standard designation(s) of the fitting system(s) for which the tubing is recommended by the manufacturer, and shall be marked, as applicable, with the following fitting system designation(s): ASTM F1807, ASTM F1960, and ASTM F2159. [4] Tubing certified against ASTM F2769 and CSA B137.18 shall include the standard designation(s) of the fitting system(s) for which the tubing is recommended by the manufacturer, and shall be marked, as applicable, with the following fitting system designation(s): ASTM F1807, ASTM F2159 and ASTM F1960.
Tubing$ +	PE 3608/4710	Oil Creek Aqua-Jet (CTS)	ASTM D2737
3/4" - 2" SDR 9
$ These products also meet the requirements for PE 3408 per ASTM D3350-02a. + Material complies with NSF/ANSI/CAN 61 health effects requirements when tested at 73° F.
Tubing+	PE 3608/4710		ASTM D2737
3/4" - 2" SDR 9
+ Material complies with NSF/ANSI/CAN 61 health effects requirements when tested at 73° F.
Pipe$ +	PE 3608/4710	Aqua-Blue	ASTM D2239
3/4" - 2" SIDR 5.3
3/4" - 2" SIDR 7
3/4" - 2" SIDR 9
1/2" - 2" SIDR 11.5[2]
3/4" - 2" SIDR 15[2]
3/4" - 2" SIDR 19[2]
[2] These pipe sizes shall not be marked with a CC oxidative resistance classification and are not certified for use in applications where an oxidative resistance classification (e.g. CC1, CC2, CC3), in accordance with ASTM D3350, is required. $ These products also meet the requirements for PE 3408 per ASTM D3350-02a. + Material complies with NSF/ANSI/CAN 61 health effects requirements when tested at 73° F.
Pipe+	PE 3608/4710	Aqua-Blue	ASTM D2737
3/4" - 2" SDR 9
+ Material complies with NSF/ANSI/CAN 61 health effects requirements when tested at 73° F.
Tubing$ +	PE 3608/4710	Oil Creek Aqua-Jet (OD)	ASTM D3035
1/2" DR 7[2]
1/2" DR 9[2]
1/2" - 3" DR 11[2]
1/2" - 3" DR 13.5[2]
3/4" - 3" DR 7
3/4" - 3" DR 9
3/4" - 3" DR 15.5[2]
3/4" - 3" DR 17[2]
1" - 3" DR 21[2]
[2] These pipe sizes shall not be marked with a CC oxidative resistance classification and are not certified for use in applications where an oxidative resistance classification (e.g. CC1, CC2, CC3), in accordance with ASTM D3350, is required. $ These products also meet the requirements for PE 3408 per ASTM D3350-02a. + Material complies with NSF/ANSI/CAN 61 health effects requirements when tested at 73° F.
Tubing$ +	PE 3608/4710	Oil Creek Aqua-Jet (OD)	ASTM F714
4" - 8" DR 7
4" - 8" DR 7.3
4" - 8" DR 9
4" - 8" DR 11
4" - 8" DR 13.5
4" - 8" DR 15.5[3]
4" - 8" DR 17
4" - 8" DR 21
[3] Special sizes may be acceptable for engineered applications, due to system conditions or special local requirements. It is the responsibility of the end user to ensure the product is suitable for the intended application. $ These products also meet the requirements for PE 3408 per ASTM D3350-02a. + Material complies with NSF/ANSI/CAN 61 health effects requirements when tested at 73° F.

Radiant Floor Heating

Product Type	Material Type	Trade Name	Product Standard
Tubing! ¥ [1] [2] [3]*	PE-RT PE 2708	Heatflex	ASTM F2623
5/16" SDR 9
3/8" SDR 9
1/2" SDR 9
5/8" SDR 9
3/4" SDR 9
1" SDR 9
! Heatflex/[Oil Creek Plastics Oil Rig Logo] PE-RT pipe is orange in color. * Product is barrier tubing. ¥ Product is Certified to the Uniform Mechanical Code™. Installation in accordance with the manufacturer's instructions and the requirements of the latest edition of the Uniform Mechanical Code™. [1] This barrier tubing product has been evaluated against the performance requirements of ASTM F2623. This product is not NSF Certified for use in a potable water distribution system. This product has been evaluated for use in radiant floor heating (NSF-rfh) applications only. [2] Meets the chlorine resistance requirements of ASTM F2623 when tested in accordance with ASTM F2023. [3] Tubing certified against ASTM F2623 shall include the standard designation(s) of the fitting system(s) for which the tubing is recommended by the manufacturer, and shall be marked, as applicable, with the following fitting system designation(s): ASTM F1807 and ASTM F2159.
Tubing! ¥ [1] [2] [3]*	PE-RT PE 2708	PERTCO	ASTM F2623
5/16" SDR 9
3/8" SDR 9
1/2" SDR 9
5/8" SDR 9
3/4" SDR 9
1" SDR 9
! Heatflex/[Oil Creek Plastics Oil Rig Logo] PE-RT pipe is orange in color. * Product is barrier tubing. ¥ Product is Certified to the Uniform Mechanical Code™. Installation in accordance with the manufacturer's instructions and the requirements of the latest edition of the Uniform Mechanical Code™. [1] This barrier tubing product has been evaluated against the performance requirements of ASTM F2623. This product is not NSF Certified for use in a potable water distribution system. This product has been evaluated for use in radiant floor heating (NSF-rfh) applications only. [2] Meets the chlorine resistance requirements of ASTM F2623 when tested in accordance with ASTM F2023. [3] Tubing certified against ASTM F2623 shall include the standard designation(s) of the fitting system(s) for which the tubing is recommended by the manufacturer, and shall be marked, as applicable, with the following fitting system designation(s): ASTM F1807 and ASTM F2159.
Tubing ¥ ‡ [1] [2] [3]*	PE-RT PE 2708	Propak Heatflex	ASTM F2623
5/16" SDR 9
3/8" SDR 9
1/2" SDR 9
5/8" SDR 9
3/4" SDR 9
1" SDR 9
* Product is barrier tubing. ¥ Product is Certified to the Uniform Mechanical Code™. Installation in accordance with the manufacturer's instructions and the requirements of the latest edition of the Uniform Mechanical Code™. ‡ Propak Heatflex/[Oil Creek Plastics Oil Rig Logo] PE-RT pipe is orange in color. [1] This barrier tubing product has been evaluated against the performance requirements of ASTM F2623. This product is not NSF Certified for use in a potable water distribution system. This product has been evaluated for use in radiant floor heating (NSF-rfh) applications only. [2] Meets the chlorine resistance requirements of ASTM F2623 when tested in accordance with ASTM F2023. [3] Tubing certified against ASTM F2623 shall include the standard designation(s) of the fitting system(s) for which the tubing is recommended by the manufacturer, and shall be marked, as applicable, with the following fitting system designation(s): ASTM F1807 and ASTM F2159.
Tubing! ¥ ‡ [1] [2] [3]*	PE-RT PE 2708		ASTM F2623
5/16" SDR 9
3/8" SDR 9
1/2" SDR 9
5/8" SDR 9
3/4" SDR 9
1" SDR 9
! Heatflex/[Oil Creek Plastics Oil Rig Logo] PE-RT pipe is orange in color. * Product is barrier tubing. ¥ Product is Certified to the Uniform Mechanical Code™. Installation in accordance with the manufacturer's instructions and the requirements of the latest edition of the Uniform Mechanical Code™. ‡ Propak Heatflex/[Oil Creek Plastics Oil Rig Logo] PE-RT pipe is orange in color. [1] This barrier tubing product has been evaluated against the performance requirements of ASTM F2623. This product is not NSF Certified for use in a potable water distribution system. This product has been evaluated for use in radiant floor heating (NSF-rfh) applications only. [2] Meets the chlorine resistance requirements of ASTM F2623 when tested in accordance with ASTM F2023. [3] Tubing certified against ASTM F2623 shall include the standard designation(s) of the fitting system(s) for which the tubing is recommended by the manufacturer, and shall be marked, as applicable, with the following fitting system designation(s): ASTM F1807 and ASTM F2159.

Rheogistics, A Division of IGI
50 Salome Drive
Toronto, ON M1S 2A8
Canada
416-293-4151

Facility : Titusville, PA

Ingredient Suppliers

Product Type	Trade Name	Max Use Level (phr)
Combination Ingredient Package+ [1] [3] [9]	Synertive L355	0.68 - 1.68
Paraffin Wax+ [2]	Synertive RX-165	0.6 - 1.5
Paraffin Wax+ [2]	Synertive RX-165 Classic	0.6 - 1.5
Combination Ingredient Package[1] [3] [4]	Synertive RX-310	0.54 - 1.66
Combination Ingredient Package[1] [3] [5]	Synertive RX-313	0.8 - 1.73
Combination Ingredient Package[1] [3] [6]	Synertive RX-315-S	0.7 - 1.77
Combination Ingredient Package[1] [3] [7]	Synertive RX-320	0.74 - 1.6
Combination Ingredient Package[1] [3] [8]	Synertive RX-320-S	0.75 - 1.5
+ Material complies with NSF/ANSI/CAN 61 health effects requirements when tested at 73° F. [1] Use of this ingredient in NSF Certified products requires prior authorization from NSF, unless user is an authorized holder of the PPI PVC Range Composition. [2] Certified to NSF/ANSI 14 and also approved in Table 4A of the PPI PVC Range Composition. Approved for a use range of 0.60 - 1.5 phr. [3] For PPI PVC Range Composition holders, see the PPI PVC Range Composition for individual ingredient contributions. Additional amounts of other approved ingredients can be added, but the total combined percentage cannot exceed 100% of the allowable phr. [4] Certified to NSF/ANSI 14 and also approved in Table 10A of the PPI PVC Range Composition. Approved for a use range of 0.54 - 1.66 phr. [5] Certified to NSF/ANSI 14 and also approved in Table 10A of the PPI PVC Range Composition. Approved for a use range of 0.8 - 1.73 phr. [6] Certified to NSF/ANSI 14 and also approved in Table 10A of the PPI PVC Range Composition. Approved for a use range of 0.7 - 1.77 phr. [7] Certified to NSF/ANSI 14 and also approved in Table 10A of the PPI PVC Range Composition. Approved for a use range of 0.74 - 1.6 phr. [8] Certified to NSF/ANSI 14 and also approved in Table 10A of the PPI PVC Range Composition. Approved for a use range of 0.75 - 1.5 phr. [9] Certified to NSF/ANSI 14 and also approved in Table 10A of the PPI PVC Range Composition. Approved for a use range of 0.68 - 1.68 phr.

SONNEBORN, LLC
100 Sonneborn Lane
Petrolia, PA 16050
United States
877-948-2688

Facility : Petrolia, PA

Ingredient Suppliers

Product Type

Trade Name

Max Use Level (phr)

Paraffin Wax Functional Equivalent+ [1] [2] [3]

HYDROBRITE PVC OIL

2.00

+ Material complies with NSF/ANSI/CAN 61 health effects requirements when tested at 73° F.
[1] Certified to NSF/ANSI 14 and also approved in Table 4B of the PPI PVC Range Composition.
     Approved for a use range of1.00 - 2.00 phr.
[2] Cannot be used with other functional equivalent ingredients.
[3] Use of this ingredient in NSF Certified products requires prior authorization from NSF,
    unless user is an authorized holder of the PPI PVC Range Composition.

The Mosack Group
701 Matthews Mint-Hill Road
Matthews, NC 28105
United States
888-229-2874
Visit this company's website

Facility : Brave, PA

Potable Water - Pipe and Fittings

Product Type	Material Type	Trade Name	Product Standard
Fittings¢ § +++ [G]	Brass	AF PEX LEADFREE	ASTM F1807
MPT x PEX Barb Elbow
3/8" - 2"
Male Sweat x PEX Barb
3/8" - 2"
PEX Barb Adapter
3/8" - 2"
PEX Barb Coupling
3/8" - 2"
PEX Barb Elbow
3/8" - 2"
PEX Barb Plug
3/8" - 2"
PEX Barb Reducing Coupling
3/8" - 2"
PEX Barb Reducing Elbow
3/8" - 2"
PEX Barb Reducing Tee
3/8" - 2"
PEX Barb Swivel Adapters
3/8" - 3/4"
PEX Barb Tee
3/8" - 2"
PEX Barb x Compression Adapter
3/8" - 3/4"
PEX Barb x Cu Sweat Elbow
3/8" - 2"
PEX Barb x FIP Swivel Adapter
3/8" - 2"
PEX Barb x FPT Adapter
3/8" - 2"
PEX Barb x FPT Drop Ear Elbow
1/2" - 3/4"
PEX Barb x Female Sweat Adapter
3/8" - 2"
PEX Barb x MPT Adapter
3/8" - 2"
PEX Barb x PB Tube Coupling
3/8" - 1"
PEX Barb x PE Tube Coupling
3/8" - 1"
PEX Barb x Swivel Adapter
3/8" - 2"
Plug Seal Manifold
3/8" - 2"
¢ Product is authorized to bear the cNSF and/or the cNSFus Mark. § Product is Certified to the Uniform Plumbing Code™. Installation in accordance with the manufacturer's instructions and the requirements of the latest edition of the Uniform Plumbing Code™. +++ Material complies with NSF/ANSI/CAN 61 health effects requirements when tested at temperatures up to and including Commercial Hot (180° F). [G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state laws and the U.S. Safe Drinking Water Act.
Fittings¢ § +++ [G]	Brass	AF PEX LEADFREE	CSA B137.5
MPT x PEX Barb Elbow
3/8" - 2"
Male Sweat x PEX Barb
3/8" - 2"
PEX Barb Adapter
3/8" - 2"
PEX Barb Coupling
3/8" - 2"
PEX Barb Elbow
3/8" - 2"
PEX Barb Plug
3/8" - 2"
PEX Barb Reducing Coupling
3/8" - 2"
PEX Barb Reducing Elbow
3/8" - 2"
PEX Barb Reducing Tee
3/8" - 2"
PEX Barb Swivel Adapters
3/8" - 3/4"
PEX Barb Tee
3/8" - 2"
PEX Barb x Compression Adapter
3/8" - 3/4"
PEX Barb x Cu Sweat Elbow
3/8" - 2"
PEX Barb x FIP Swivel Adapter
3/8" - 2"
PEX Barb x FPT Adapter
3/8" - 2"
PEX Barb x FPT Drop Ear Elbow
1/2" - 3/4"
PEX Barb x Female Sweat Adapter
3/8" - 2"
PEX Barb x MPT Adapter
3/8" - 2"
PEX Barb x PB Tube Coupling
3/8" - 1"
PEX Barb x PE Tube Coupling
3/8" - 1"
PEX Barb x Swivel Adapter
3/8" - 2"
Plug Seal Manifold
3/8" - 2"
¢ Product is authorized to bear the cNSF and/or the cNSFus Mark. § Product is Certified to the Uniform Plumbing Code™. Installation in accordance with the manufacturer's instructions and the requirements of the latest edition of the Uniform Plumbing Code™. +++ Material complies with NSF/ANSI/CAN 61 health effects requirements when tested at temperatures up to and including Commercial Hot (180° F). [G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state laws and the U.S. Safe Drinking Water Act.

Westlake Pipe & Fittings Corporation
The Westlake Center
2801 Post Oak Boulevard, Suite 650
Houston, TX 77056
United States
800-999-7473
713-585-2621

Facility : Leola, PA

Drain, Waste, and Vent - Pipe and Fittings

Product Type	Material Type	Trade Name	Product Standard
Pipe[1] [2]	PVC	Westlake Pipe & Fittings	ASTM D2665
1 1/4" - 12" Sch 40
[1] Product may also be marked with trade designation Westlake Canada, Inc. DBA Westlake Pipe & Fittings. [2] Sockets and gasketed bell ends are not tested or Listed by NSF for this production facility.
Pipe[1]	PVC	Westlake Pipe & Fittings	ASTM D2949
3.25"
[1] Product may also be marked with trade designation Westlake Canada, Inc. DBA Westlake Pipe & Fittings.
Pipe[1]	PVC	Westlake Pipe & Fittings	ASTM F3128
1 1/4" - 6"
[1] Product may also be marked with trade designation Westlake Canada, Inc. DBA Westlake Pipe & Fittings.
Pipe[1]	PVC	NAPCOREtm	ASTM F3128
1 1/4" - 6"
[1] Product may also be marked with trade designation Westlake Canada, Inc. DBA Westlake Pipe & Fittings.
Pipe[1]	PVC	Westlake Pipe & Fittings	ASTM F891
1 1/4" - 6" Sch 40
[1] Product may also be marked with trade designation Westlake Canada, Inc. DBA Westlake Pipe & Fittings.

NOTE: Only products bearing the NSF Mark on the product, product packaging, and/or
      documentation shipped with the product are Certified.

Potable Water - Pipe and Fittings

Product Type	Material Type	Trade Name	Product Standard
Pipe+ [1] [2] [G]	PVC	Westlake Pipe & Fittings	ASTM D1785
1/2" - 12" Sch 40
1/2" - 12" Sch 80
+ Material complies with NSF/ANSI/CAN 61 health effects requirements when tested at 73° F. [1] Product may also be marked with trade designation Westlake Canada, Inc. DBA Westlake Pipe & Fittings. [2] Sockets and gasketed bell ends are not tested or Listed by NSF for this production facility. [G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state laws and the U.S. Safe Drinking Water Act.
Pipe+ [1] [2] [G]	PVC	Westlake Pipe & Fittings	ASTM D2241
1/2" - 6" SDR 13.5
>= 3/4" SDR 17
>= 3/4" SDR 21
>= 1" SDR 26
>= 1" SDR 32.5
>= 3" SDR 41
+ Material complies with NSF/ANSI/CAN 61 health effects requirements when tested at 73° F. [1] Product may also be marked with trade designation Westlake Canada, Inc. DBA Westlake Pipe & Fittings. [2] Sockets and gasketed bell ends are not tested or Listed by NSF for this production facility. [G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state laws and the U.S. Safe Drinking Water Act.

NOTE: Only products bearing the NSF Mark on the product, product packaging, and/or
      documentation shipped with the product are Certified.

Well Casings

Product Type	Material Type	Trade Name	Product Standard
Well Casings[1] [2] [G]	PVC	Westlake Pipe & Fittings	ASTM F480
2" - 12" Sch 40
2" - 4 1/2" SDR 32.5
4 1/2" SDR 17
6 1/8" ID SDR 21
6 1/4" DR 27.6
[1] Product may also be marked with trade designation Westlake Canada, Inc. DBA Westlake Pipe & Fittings. [2] Sockets and gasketed bell ends are not tested or Listed by NSF for this production facility. [G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state laws and the U.S. Safe Drinking Water Act.

NOTE: Only products bearing the NSF Mark on the product,product packaging, and/or
      documentation shipped with the product are Certified.

WL Plastics Corporation
3575 Lone Star Circle
Suite 300
Fort Worth, TX 76177
United States
682-831-2727
Visit this company's website

Facility : Titusville, PA

Gas Applications - Pipe and Fittings

Product Type	Material Type	Trade Name	Product Standard
Pipe§	PE 2708	WL Plastics PA/WLP PA	ASTM D2513
1/2" CTS 0.090 WALL
3/4" CTS 0.090 WALL
1” CTS 0.090 WALL, 0.099 WALL, 0.101 WALL
1-1/4” CTS 0.062 WALL, 0.090 WALL, 0.121 WALL SDR 9.3
1/2" IPS SDR 9, 9.3, 9.33, 11 SDR 11
3/4" IPS SDR 11 SDR 11
1” IPS SDR 11 SDR 10, 11
1-1/4” IPS SDR 10, 11 SDR 11
1-1/2" IPS SDR 11 SDR 11
2” IPS SDR 11, 13.5 SDR 11, 11.5
3” IPS SDR 9, 11, 11.5, 13.5 SDR 11, 11.5, 13.5
4” IPS SDR 9, 11, 11.5, 13.5, 17 SDR 11, 11.5, 13.5
6” IPS SDR 9, 11, 11.5, 13.5, 17 SDR 11, 11.5, 13.5
8” IPS SDR 9, 11, 11.5, 13.5, 17 SDR 11, 11.5, 13.5
§ Product is Certified to the Uniform Plumbing Code™. Installation in accordance with the manufacturer's instructions and the requirements of the latest edition of the Uniform Plumbing Code™.
Pipe§	PE 4710	WL Plastics PA/WLP PA	ASTM D2513
1/2" CTS 0.090 WALL
3/4" CTS 0.090 WALL
1” CTS 0.090 WALL, 0.099 WALL, 0.101 WALL, 0.121 WALL
1-1/4” CTS 0.090 WALL, 0.121 WALL
3/4" IPS SDR 7.3, 9, 11 SDR 7.3, 9, 11
1” IPS SDR 7, 7.3, 9, 11 SDR 7.3, 9, 11
1-1/4” IPS SDR 7, 7.3, 9, 10, 11 SDR 7.3, 9, 11
1-1/2" IPS SDR 7, 7.3, 9, 11 SDR 7.3, 9, 11
2” IPS SDR 7, 7.3, 9, 11, 13.5, 15.5, 17 SDR 7.3, 9, 11, 13.5, 15.5, 17
3” IPS SDR 7, 7.3, 9, 11, 11.5, 13.5, 15.5, 17 SDR 7.3, 9, 11, 13.5, 15.5, 17
4” IPS SDR 7, 7.3, 9, 11, 11.5, 13.5, 15.5, 17 SDR 7.3, 9, 11, 13.5, 15.5, 17
6” IPS SDR 7, 7.3, 9, 11, 11.5, 13.5, 15.5, 17 SDR 9, 11, 13.5, 15.5, 17
8” IPS SDR 7, 7.3, 9, 11, 11.5, 13.5, 15.5, 17 SDR 11, 13.5, 15.5, 17
10” IPS SDR 7, 9, 11, 13,5, 15.5, 17 SDR 13.5, 15.5, 17
12” IPS SDR 7, 9, 11, 13.5, 15.5, 17 SDR 15.5, 17
§ Product is Certified to the Uniform Plumbing Code™. Installation in accordance with the manufacturer's instructions and the requirements of the latest edition of the Uniform Plumbing Code™.
Pipe¢	PE 2708	WL Plastics PA/WLP PA	CSA B137.4
1/2" CTS .090 wall
1" CTS .099 wall
1 1/4" SDR 10
3/4" - 2" SDR 11
¢ Product is authorized to bear the cNSF and/or the cNSFus Mark.

Potable Water - Pipe and Fittings

Product Type	Material Type	Trade Name	Product Standard
Pipe+	PE 4710	WL Plastics PA/WLP PA	ASTM D2239
3/4" - 2" SIDR 5.3
3/4" - 2" SIDR 7
3/4" - 2" SIDR 9
1/2" - 3" SIDR 11.5[1]
3/4" - 3" SIDR 15[1]
1/2" - 2" SIDR 19[1]
[1] These pipe sizes are not certified for use in potable water applications containing oxidizing disinfectants and shall not be marked with a CC oxidative resistance classification. + Material complies with NSF/ANSI/CAN 61 health effects requirements when tested at 73° F.
Pipe+	PE 4710	WL Plastics PA/WLP PA	ASTM D3035
1/2" DR 7[1]
3/4" - 3" DR 7
1/2" DR 9[1]
3/4" - 3" DR 9
1/2" - 3" DR 11[1]
1/2" - 3" DR 13.5[1]
3/4" - 3" DR 15.5[1]
3/4" - 3" DR 17[1]
1" - 3" DR 21[1]
1" - 3" DR 26[1]
1 1/2" - 3" DR 32.5[1]
[1] These pipe sizes are not certified for use in potable water applications containing oxidizing disinfectants and shall not be marked with a CC oxidative resistance classification. + Material complies with NSF/ANSI/CAN 61 health effects requirements when tested at 73° F.
Pipe+	PE 4710	WL Plastics PA/WLP PA	ASTM D2737
3/4" - 2" SDR 9
+ Material complies with NSF/ANSI/CAN 61 health effects requirements when tested at 73° F.
Pipe+	PE 4710	WL Plastics PA/WLP PA	ASTM F714
4" - 18" IPS DR 7.3
4" - 26" IPS DR 7
4" - 36" IPS DR 9
4" - 42" IPS DR 11
4" - 48" IPS DR 13.5
4" - 54" IPS DR 15.5[2]
4" - 54" IPS DR 17
4" - 54" IPS DR 21
4" - 54" IPS DR 26
4" - 54" IPS DR 32.5
4" - 54" IPS DR 41
[2] Special sizes may be acceptable for engineered applications, due to system conditions or special local requirements. It is the responsibility of the end user to ensure the product is suitable for the intended application. + Material complies with NSF/ANSI/CAN 61 health effects requirements when tested at 73° F.
Pipe+	PE 4710	WL Plastics PA/WLP PA	AWWA C901
3/4" - 3" IPS SDR 9
+ Material complies with NSF/ANSI/CAN 61 health effects requirements when tested at 73° F.
Pipe+	PE 3608/4710	WL Plastics PA/WLP PA Blue	ASTM D2239
3/4" - 2" SIDR 5.3
3/4" - 2" SIDR 7
3/4" - 2" SIDR 9
1/2" - 3" SIDR 11.5[1]
3/4" - 3" SIDR 15[1]
1/2" - 2" SIDR 19[1]
[1] These pipe sizes are not certified for use in potable water applications containing oxidizing disinfectants and shall not be marked with a CC oxidative resistance classification. + Material complies with NSF/ANSI/CAN 61 health effects requirements when tested at 73° F.
Pipe+	PE 4710	WL Plastics PA/WLP PA Blue	ASTM D3035
1/2" DR 7[1]
3/4" - 3" DR 7
1/2" DR 9[1]
3/4" - 3" DR 9
1/2" - 3" DR 11[1]
1/2" - 3" DR 13.5[1]
3/4" - 3" DR 15.5[1]
3/4" - 3" DR 17[1]
1" - 3" DR 21[1]
1" - 3" DR 26[1]
1 1/2" - 3" DR 32.5[1]
[1] These pipe sizes are not certified for use in potable water applications containing oxidizing disinfectants and shall not be marked with a CC oxidative resistance classification. + Material complies with NSF/ANSI/CAN 61 health effects requirements when tested at 73° F.
Pipe+	PE 4710	WL Plastics PA/WLP PA Blue	ASTM D2737
3/4" - 2" SDR 9
+ Material complies with NSF/ANSI/CAN 61 health effects requirements when tested at 73° F.
Pipe+	PE 4710	WL Plastics PA/WLP PA Blue	ASTM F714
4" - 18" IPS DR 7.3
4" - 26" IPS DR 7
4" - 36" IPS DR 9
4" - 42" IPS DR 11
4" - 48" IPS DR 13.5
4" - 54" IPS DR 15.5[2]
4" - 54" IPS DR 17
4" - 54" IPS DR 21
4" - 54" IPS DR 26
4" - 54" IPS DR 32.5
4" - 54" IPS DR 41
[2] Special sizes may be acceptable for engineered applications, due to system conditions or special local requirements. It is the responsibility of the end user to ensure the product is suitable for the intended application. + Material complies with NSF/ANSI/CAN 61 health effects requirements when tested at 73° F.
Pipe+	PE 4710	WL Plastics PA/WLP PA Blue	AWWA C901
3/4" - 3" IPS SDR 9
+ Material complies with NSF/ANSI/CAN 61 health effects requirements when tested at 73° F.
Pipe +*	PE 4710	WL Plastics PA/WLP PA	AWWA C906
4" - 24" IPS DR 7
4" - 24" IPS DR 7.3[2]
4" - 24" IPS DR 9
4" - 24" IPS DR 11
4" - 24" IPS DR 13.5
4" - 24" IPS DR 15.5[2]
4" - 24" IPS DR 17
4" - 24" IPS DR 21
4" - 24" IPS DR 26[2]
4" - 24" IPS DR 32.5[2]
[2] Special sizes may be acceptable for engineered applications, due to system conditions or special local requirements. It is the responsibility of the end user to ensure the product is suitable for the intended application. * Product tested and Certified for Cold 23°C (73°F) applications only. + Material complies with NSF/ANSI/CAN 61 health effects requirements when tested at 73° F.

Zurn PEX, Inc.
116 Maple Street
Commerce, TX 75428
United States
903-886-2580
Visit this company's website

Facility : Harborcreek, PA

Fire Sprinkler Pipe and Fitting Systems

Product Type	Material Type	Trade Name	Product Standard
Pipe and Fitting System% * [G]*	MLTPL	Zurn PEX Fire Protection System	ANSI/CAN/UL 1821
Coupling (BARB x BARB)
1" barb x 1" barb (QQC55GFX)	1" barb x 1" barb (QQPC55FX)	1 1/4" barb x 1 1/4" barb (QQC66GFX)	1 1/2" barb x 1 1/2" barb (QQC77GFX)
2" barb x 2" barb (QQC88GFX)
Crimp Coupling
1" Crimp PEX X 1/2" FPT (QQFSC53GFX)
Crimp Tee
1" Crimp PEX x 1" Crimp PEX x 1/2" FPT (QQFST553GFX)
Elbow (BARB X BARB)
1" barb x 1" barb (QQPE55FX)	1" barb x 1" barb (QQE55GFX)	1 1/4" barb x 1 1/4" barb (QQE66GFX)	1 1/2" barb x 1 1/2" barb (QQE77GFX)
2" barb x 2" barb (QQE88GFX)
Expansion Coupling
1" EXP PEX x 1/2" FPT (QEFSC53GFX)
Expansion Tee
1" EXP PEX x 1" EXP PEX x 1/2" FPT (QEFST553FGX)
Female Adapter (BARB x FPT)
1" barb x 1" FPT (QQUFC55GFX)	1 1/4" barb x 1 1/4" FPT (QQUFC66GFX)	1 1/2" barb x 1 1/2" FPT (QQUFC77GFX)
Female Sweat Adapter (BARB x SWEAT)
1" barb x 1" sweat (QQ800CFX)	1 1/4" barb x 1 1/4" sweat (QQ812GFX)	1 1/2" barb x 1 1/2" sweat (QQ950GFX)	2" barb x 2" sweat (QQ1050GFX)
Fire Sprinkler Coupling
1" barb x 1/2" FPT (QQFSC53GFX)
Fire Sprinkler Tee (BARB X BARB X FPT)
1" barb x 1" barb x 1/2" FPT (QQFST553GFX)
Male Adapter (BARB X MPT)
1" barb x 1" MPT (QQMC55GFX)	1" barb x 1" barb MPT (QQPMC55FX)	1 1/4" barb x 1 1/4" MPT (QQMC66GFX)	1 1/2" barb x 1 1/2" MPT (QQMC77GFX)
2" barb x 2" MPT (QQMC88GFX)
Male Sweat Adapter (BARB X SWEAT)
1" barb x 1" sweat (QQ700CFX)
Plug (Barb)
1" (QQP5GFX)	1 1/4" (QQP6GFX)	1 1/2" (QQP7GFX)	2" (QQP8GFX)
Reducer Tee (BARB X BARB X BARB)
1" barb x 1" barb x 1/2" barb (QQT553GFX)	1" barb x 1" barb x 3/4" barb (QQT554GFX)	1" barb x 1" barb x 1/2" barb (QQPT553FX)	1" barb x 1" barb x 3/4" barb (QQPT554FX)
1 1/4" barb x 1 1/4" barb x 1/2" barb (QQT663GFX)	1 1/4" barb x 1 1/4" barb x 3/4" barb (QQT664GFX)	1 1/2" barb x 1 1/2" barb x 3/4" barb (QQT774GFX)	1 1/2" barb x 1 1/2" barb x 1" barb (QQT775GFX)
2" barb x 2" barb x 1" barb (QQT885GFX)
Reducing Coupling (BARB x BARB)
1" barb x 3/4" barb (QQPC54FX)	1 1/4" barb x 1" barb (QQC65GFX)	1 1/2" barb x 1 1/4" barb (QQC76GFX)	2" barb x 1 1/2" barb (QQC87GFX)
Tee (BARB X BARB X BARB)
1" barb x 1" barb x 1" barb (QQT555GFX)	1" barb x 1" barb x 1" barb (QQPT555GFX)	1 1/4" barb x 1 1/4" barb x 1 1/4" barb (QQT666GFX)	1 1/2" barb x 1 1/2" barb x 1 1/2" barb (QQT777GFX)
2" barb x 2" barb x 2" barb (QQT888GFX)
Tubing
1" – 2" White ZurnPEX
% PEX pipe and fittings are intended for use in multi-purpose piping systems of residential occupancies as defined in ANSI/NFPA 13D, "Installation of Sprinkler Systems in One- and Two- Family Dwellings and Manufactured Homes" and the International Residential Code, Section 2904, and are designed to withstand a working pressure of not less than 130 psi at 120° F. PEX pipe and fittings are intended to be installed in accordance with the requirements specified in the manufacturer’s installation instructions and ANSI/NFPA 13D. Protection is intended to be provided for PEX pipe and fittings in multi-purpose piping systems. The minimum protection should consist of either (1) one layer of 3/8-in. gypsum wallboard, (2) a suspended membrane ceiling with lay-in panels or tiles having a weight of not less than 0.35 lbs per sq ft when installed with metallic support grids, (3) 1/2 in plywood or (4) other material with a 15 minute fire rating. PEX pipe and fittings are intended for use in areas where the maximum ambient temperature does not exceed 120° F. These pipe and fittings are not intended to be installed in outdoor applications. The PEX pipe and fittings are intended for use in wet-pipe systems only and have not been evaluated for use in dry-pipe systems. ** Pipe and fittings Certified as a system using Installation/assembly instructions titled "Zurn PEX Residential Fire Protection Addendum to Plumbing Installation Guide". [G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state laws and the U.S. Safe Drinking Water Act.

Potable Water - Pipe and Fittings

Product Type	Material Type	Trade Name	Product Standard
Tubing# ^ ¢ § +++ [G]	PEX 5306	ACCUTEK PEX - Blue, Red, White	ASTM F876/F877
1/8" - 2" SDR 9
# Tubing certified against CSA B137.5 shall include the standard designation(s) of the fitting system(s) for which the tubing is recommended by the manufacturer, and shall be marked, as applicable, with the following fitting system designation(s): ASTM F1807, ASTM F2159, ASTM F1960, ASTM F2098 and ASTM F876/F877. ^ Meets the chlorine resistance requirements of ASTM F876 when tested in accordance with ASTM 2023. ¢ Product is authorized to bear the cNSF and/or the cNSFus Mark. § Product is Certified to the Uniform Plumbing Code™. Installation in accordance with the manufacturer's instructions and the requirements of the latest edition of the Uniform Plumbing Code™. +++ Material complies with NSF/ANSI/CAN 61 health effects requirements when tested at temperatures up to and including Commercial Hot (180° F). [G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state laws and the U.S. Safe Drinking Water Act.
Tubing^ ¢ § +++ [G]	PEX 5306	ACCUTEK PEX - Blue, Red, White	AWWA C904
1/2" - 2" SDR 9
^ Meets the chlorine resistance requirements of ASTM F876 when tested in accordance with ASTM 2023. ¢ Product is authorized to bear the cNSF and/or the cNSFus Mark. § Product is Certified to the Uniform Plumbing Code™. Installation in accordance with the manufacturer's instructions and the requirements of the latest edition of the Uniform Plumbing Code™. +++ Material complies with NSF/ANSI/CAN 61 health effects requirements when tested at temperatures up to and including Commercial Hot (180° F). [G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state laws and the U.S. Safe Drinking Water Act.
Tubing# ^ ¢ § +++ [G]	PEX	ACCUTEK PEX - Blue, Red, White	CSA B137.5
1/8" - 2" SDR 9
# Tubing certified against CSA B137.5 shall include the standard designation(s) of the fitting system(s) for which the tubing is recommended by the manufacturer, and shall be marked, as applicable, with the following fitting system designation(s): ASTM F1807, ASTM F2159, ASTM F1960, ASTM F2098 and ASTM F876/F877. ^ Meets the chlorine resistance requirements of ASTM F876 when tested in accordance with ASTM 2023. ¢ Product is authorized to bear the cNSF and/or the cNSFus Mark. § Product is Certified to the Uniform Plumbing Code™. Installation in accordance with the manufacturer's instructions and the requirements of the latest edition of the Uniform Plumbing Code™. +++ Material complies with NSF/ANSI/CAN 61 health effects requirements when tested at temperatures up to and including Commercial Hot (180° F). [G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state laws and the U.S. Safe Drinking Water Act.
Tubing# ^ ¢ § +++ [G]	PEX 5306	CAST Fast-Fit - Blue, Red, White	ASTM F876/F877
1/8" - 2" SDR 9
# Tubing certified against CSA B137.5 shall include the standard designation(s) of the fitting system(s) for which the tubing is recommended by the manufacturer, and shall be marked, as applicable, with the following fitting system designation(s): ASTM F1807, ASTM F2159, ASTM F1960, ASTM F2098 and ASTM F876/F877. ^ Meets the chlorine resistance requirements of ASTM F876 when tested in accordance with ASTM 2023. ¢ Product is authorized to bear the cNSF and/or the cNSFus Mark. § Product is Certified to the Uniform Plumbing Code™. Installation in accordance with the manufacturer's instructions and the requirements of the latest edition of the Uniform Plumbing Code™. +++ Material complies with NSF/ANSI/CAN 61 health effects requirements when tested at temperatures up to and including Commercial Hot (180° F). [G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state laws and the U.S. Safe Drinking Water Act.
Tubing^ ¢ § +++ [G]	PEX 5306	CAST Fast-Fit - Blue, Red, White	AWWA C904
1/2" - 2" SDR 9
^ Meets the chlorine resistance requirements of ASTM F876 when tested in accordance with ASTM 2023. ¢ Product is authorized to bear the cNSF and/or the cNSFus Mark. § Product is Certified to the Uniform Plumbing Code™. Installation in accordance with the manufacturer's instructions and the requirements of the latest edition of the Uniform Plumbing Code™. +++ Material complies with NSF/ANSI/CAN 61 health effects requirements when tested at temperatures up to and including Commercial Hot (180° F). [G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state laws and the U.S. Safe Drinking Water Act.
Tubing# ^ ¢ § +++ [G]	PEX	CAST Fast-Fit - Blue, Red, White	CSA B137.5
1/8" - 2" SDR 9
# Tubing certified against CSA B137.5 shall include the standard designation(s) of the fitting system(s) for which the tubing is recommended by the manufacturer, and shall be marked, as applicable, with the following fitting system designation(s): ASTM F1807, ASTM F2159, ASTM F1960, ASTM F2098 and ASTM F876/F877. ^ Meets the chlorine resistance requirements of ASTM F876 when tested in accordance with ASTM 2023. ¢ Product is authorized to bear the cNSF and/or the cNSFus Mark. § Product is Certified to the Uniform Plumbing Code™. Installation in accordance with the manufacturer's instructions and the requirements of the latest edition of the Uniform Plumbing Code™. +++ Material complies with NSF/ANSI/CAN 61 health effects requirements when tested at temperatures up to and including Commercial Hot (180° F). [G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state laws and the U.S. Safe Drinking Water Act.
Manifolds¢ +++ [G]	PPSU	CR Manifold	ASTM F877/F2159
1" Inlet X 1" Outlet X 1/2" Outlet
3-Port [QPM553-3]	4-Port [QPM553-4]	5-Port [QPM553-5]
1" Inlet X 1/2" Outlet
3-Port [QPM53-3]	5-Port [QPM53-5]	4-Port [QPM53-4]
3/4" Inlet X 3/4" Outlet X 1/2" Outlet
2-Port [QPM443-2]	3-Port [QPM443-3]	4-Port [QPM443-4]
3/4" Inlet x 1/2" Outlet
3-Port [QPM43-3]	4-Port [QPM43-4]	5-Port [QPM43-5]
¢ Product is authorized to bear the cNSF and/or the cNSFus Mark. +++ Material complies with NSF/ANSI/CAN 61 health effects requirements when tested at temperatures up to and including Commercial Hot (180° F). [G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state laws and the U.S. Safe Drinking Water Act.
Manifolds¢ +++ [G]	PPSU	CR Manifold	CSA B137.5
1" Inlet X 1/2" Outlet
3-Port [QPM53-3]	4-Port [QPM53-4]	5-Port [QPM53-5]
1" Inlet x 1" Outlet X 1/2" Outlet
3-Port [QPM553-3]	4-Port [QPM553-4]	5-Port [QPM553-5]
3/4" Inlet X 3/4" Outlet X 1/2" Outlet
2-Port [QPM443-2]	3-Port [QPM443-3]	4-Port [QPM443-4]
3/4" Inlet x 1/2" Outlet
3-Port [QPM43-3]	4-Port [QPM43-4]	5-Port [QPM43-5]
¢ Product is authorized to bear the cNSF and/or the cNSFus Mark. +++ Material complies with NSF/ANSI/CAN 61 health effects requirements when tested at temperatures up to and including Commercial Hot (180° F). [G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state laws and the U.S. Safe Drinking Water Act.
Misc. Proc. Devices/Comp.& +++ [G]*	MLTPL	Q	ASTM F877
1/2" Barb x 1/2" Swivel Qickport Manifold Valve
& Certified as a component of a manifold with a maximum of 21 valves per liter for hot applications and a maximum of 27 valves per liter for cold applications. * The letter Q is acceptable to be used on fittings due to size constraints. +++ Material complies with NSF/ANSI/CAN 61 health effects requirements when tested at temperatures up to and including Commercial Hot (180° F). [G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state laws and the U.S. Safe Drinking Water Act.
Misc. Proc. Devices/Comp.& +++ [G]*	MLTPL	Q	ASTM F2159
1/2" Barb x 1/2" Swivel Qickport Manifold Valve
& Certified as a component of a manifold with a maximum of 21 valves per liter for hot applications and a maximum of 27 valves per liter for cold applications. * The letter Q is acceptable to be used on fittings due to size constraints. +++ Material complies with NSF/ANSI/CAN 61 health effects requirements when tested at temperatures up to and including Commercial Hot (180° F). [G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state laws and the U.S. Safe Drinking Water Act.
Misc. Proc. Devices/Comp.& +++ [G]*	MLTPL	Q	CSA B137.5
1/2" Barb x 1/2" Swivel Qickport Manifold Valve
& Certified as a component of a manifold with a maximum of 21 valves per liter for hot applications and a maximum of 27 valves per liter for cold applications. * The letter Q is acceptable to be used on fittings due to size constraints. +++ Material complies with NSF/ANSI/CAN 61 health effects requirements when tested at temperatures up to and including Commercial Hot (180° F). [G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state laws and the U.S. Safe Drinking Water Act.
Tubing# ^ ¢ § +++ [G]	PEX 5306	QEST®PEX - Blue, Red, White	ASTM F876/F877
1/8" - 2"
# Tubing certified against CSA B137.5 shall include the standard designation(s) of the fitting system(s) for which the tubing is recommended by the manufacturer, and shall be marked, as applicable, with the following fitting system designation(s): ASTM F1807, ASTM F2159, ASTM F1960, ASTM F2098 and ASTM F876/F877. ^ Meets the chlorine resistance requirements of ASTM F876 when tested in accordance with ASTM 2023. ¢ Product is authorized to bear the cNSF and/or the cNSFus Mark. § Product is Certified to the Uniform Plumbing Code™. Installation in accordance with the manufacturer's instructions and the requirements of the latest edition of the Uniform Plumbing Code™. +++ Material complies with NSF/ANSI/CAN 61 health effects requirements when tested at temperatures up to and including Commercial Hot (180° F). [G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state laws and the U.S. Safe Drinking Water Act.
Tubing^ ¢ § +++ [G]	PEX 5306	QEST®PEX - Blue, Red, White	AWWA C904
1/2" - 2"
^ Meets the chlorine resistance requirements of ASTM F876 when tested in accordance with ASTM 2023. ¢ Product is authorized to bear the cNSF and/or the cNSFus Mark. § Product is Certified to the Uniform Plumbing Code™. Installation in accordance with the manufacturer's instructions and the requirements of the latest edition of the Uniform Plumbing Code™. +++ Material complies with NSF/ANSI/CAN 61 health effects requirements when tested at temperatures up to and including Commercial Hot (180° F). [G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state laws and the U.S. Safe Drinking Water Act.
Tubing# ^ ¢ § +++ [G]	PEX	QEST®PEX - Blue, Red, White	CSA B137.5
1/8" - 2"
# Tubing certified against CSA B137.5 shall include the standard designation(s) of the fitting system(s) for which the tubing is recommended by the manufacturer, and shall be marked, as applicable, with the following fitting system designation(s): ASTM F1807, ASTM F2159, ASTM F1960, ASTM F2098 and ASTM F876/F877. ^ Meets the chlorine resistance requirements of ASTM F876 when tested in accordance with ASTM 2023. ¢ Product is authorized to bear the cNSF and/or the cNSFus Mark. § Product is Certified to the Uniform Plumbing Code™. Installation in accordance with the manufacturer's instructions and the requirements of the latest edition of the Uniform Plumbing Code™. +++ Material complies with NSF/ANSI/CAN 61 health effects requirements when tested at temperatures up to and including Commercial Hot (180° F). [G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state laws and the U.S. Safe Drinking Water Act.
Fittings¢ § +++ [G]	PPSU	QickSert CR*	ASTM F2159
3/8" - 1"
Coupling
1/2" x 1/2" (QQPC33X)	3/4" x 1/2" (QQPC43X)	3/4" x 3/4" (QQPC44FX)	1" x 3/4" (QQPC55FX)
1" x 1" (QQPC55FX)
Elbow
1/2" x 1/2" (QQPE33X)	3/4" x 1/2" (QQPE43X)	3/4" x 3/4" (QQPE44FX)	1" x 1" (QQPE55FX)
Male Adapter
1/2" x 1/2" (QQPMC33X)	1/2" x 3/4" (QQPMC34X)	3/4" x 3/4" (QQPMC44FX)	1" x 1" (QQPMC55FX)
NPT Elbow
1/2" x 1/2" (QQPE33BTX)	3/4" x 3/4" (QQPE44BTX)
Reducer Coupling
1" x 3/4" (QQPC54FX)
Reducer Tee
3/4" x 1/2" x 3/4" (QQPT434FX)	3/4" x 3/4" x 1/2" (QQPT443FX)	3/4" x 3/4" x 1" (QQPT445FX)	1" x 3/4" x 3/4" (QQPT544FX)
1" x 1" x 3/4" (QQPT554FX)	1" x 1" x 1/2" (QQPT553FX)
Street Elbow
1/2" x 3/8" (QQPE32BTX)
Swivel Adapter
3/8" x 1/2" (QQPSFC23X)	1/2" x 1/2" (QQPSFC33X)	3/4" x 3/4" (QQPSFC44X)
Swivel Elbow
1/2" x 1/2" (QQPE33BSX)	3/4" x 3/4" (QQPE44BSX)	3/4" x 1" (QQPSFC45X)	1" x 1" (QQPSFC55X)
Tee
1/2" x 1/2" x 1/2" (QQPT333X)	1/2" x 1/2" x 3/4" (QQPT334X)	3/4" x 1/2" x 1/2" (QQPT433X)	3/4" x 1/2" x 3/4" (QQPT434FX)
3/4" x 3/4" x 1/2" (QQPT443FX)	3/4" x 3/4" x 3/4" (QQPT444FX)	3/4" x 3/4" x 1" (QQPT445FX)	1" x 3/4" x 3/4" (QQPT544X)
1" x 1" x 1/2" (QQPT553FX)	1" x 1" x 3/4" (QQPT554FX)	1" x 1" x 1" (QQPT555FX)
* The letter Q is acceptable to be used on fittings due to size constraints. ¢ Product is authorized to bear the cNSF and/or the cNSFus Mark. § Product is Certified to the Uniform Plumbing Code™. Installation in accordance with the manufacturer's instructions and the requirements of the latest edition of the Uniform Plumbing Code™. +++ Material complies with NSF/ANSI/CAN 61 health effects requirements when tested at temperatures up to and including Commercial Hot (180° F). [G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state laws and the U.S. Safe Drinking Water Act.
Fittings¢ § +++ [G]	PPSU	QickSert CR*	ASTM F877
3/8" - 1"
Coupling
1/2" x 1/2" (QQPC33X)	3/4" x 1/2" (QQPC43X)	3/4" x 3/4" (QQPC44FX)	1" x 3/4" (QQPC55FX)
1" x 1" (QQPC55FX)
Elbow
1/2" x 1/2" (QQPE33X)	3/4" x 1/2" (QQPE43X)	3/4" x 3/4" (QQPE44FX)	1" x 1" (QQPE55FX)
Male Adapter
1/2" x 1/2" (QQPMC33X)	1/2" x 3/4" (QQPMC34X)	3/4" x 3/4" (QQPMC44FX)	1" x 1" (QQPMC55FX)
NPT Elbow
1/2" x 1/2" (QQPE33BTX)	3/4" x 3/4" (QQPE44BTX)
Reducer Coupling
1" x 3/4" (QQPC54FX)
Reducer Tee
3/4" x 1/2" x 3/4" (QQPT434FX)	3/4" x 3/4" x 1/2" (QQPT443FX)	3/4" x 3/4" x 1" (QQPT445FX)	1" x 3/4" x 3/4" (QQPT544FX)
1" x 1" x 1/2" (QQPT553FX)	1" x 1" x 3/4" (QQPT554FX)
Street Elbow
1/2" x 3/8" (QQPE32BTX)
Swivel Adapter
3/8" x 1/2" (QQPSFC23X)	1/2" x 1/2" (QQPSFC33X)	3/4" x 3/4" (QQPSFC44X)	3/4" x 1" (QQPSFC45X)
1" x 1" (QQPSFC55X)
Swivel Elbow
1/2" x 1/2" (QQPE33BSX)	3/4" x 3/4" (QQPE44BSX)
Tee
1/2" x 1/2" x 1/2" (QQPT333X)	1/2" x 1/2" x 3/4" (QQPT334X)	3/4" x 1/2" x 1/2" (QQPT433X)	3/4" x 1/2" x 3/4" (QQPT434FX)
3/4" x 3/4" x 1" (QQPT445FX)	3/4" x 3/4" x 3/4" (QQPT444FX)	1" x 3/4" x 3/4" (QQPT544X)	1" x 1" x 1/2" (QQPT553FX)
1" x 1" x 3/4" (QQPT554FX)	1" x 1" x 1" (QQPT555FX)
* The letter Q is acceptable to be used on fittings due to size constraints. ¢ Product is authorized to bear the cNSF and/or the cNSFus Mark. § Product is Certified to the Uniform Plumbing Code™. Installation in accordance with the manufacturer's instructions and the requirements of the latest edition of the Uniform Plumbing Code™. +++ Material complies with NSF/ANSI/CAN 61 health effects requirements when tested at temperatures up to and including Commercial Hot (180° F). [G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state laws and the U.S. Safe Drinking Water Act.
Fittings¢ § +++ [G]	PPSU	QickSert CR*	CSA B137.5
3/8" - 1"
Coupling
1/2" x 1/2" (QQPC33X)	3/4" x 1/2" (QQPC43X)	3/4" x 3/4" (QQPC44FX)	1" x 3/4" (QQPC55FX)
1" x 1" (QQPC55FX)
Elbow
3/4" x 1/2" (QQPE43X)	3/4" x 3/4" (QQPE44FX)	1" x 1" (QQPE55FX)
Male Adapter
1/2" x 1/2" (QQPMC33X)	1/2" x 3/4" (QQPMC34X)	3/4" x 3/4" (QQPMC44FX)	1" x 1" (QQPMC55FX)
NPT Elbow
1/2" x 1/2" (QQPE33BTX)	3/4" x 3/4" (QQPE44BTX)
Reducer Coupling
1" x 3/4" (QQPC54FX)
Reducer Tee
3/4" x 1/2" x 3/4" (QQPT434FX)	3/4" x 3/4" x 1/2" (QQPT443FX)	3/4" x 3/4" x 1" (QQPT445FX)	1" x 3/4" x 3/4" (QQPT544FX)
1" x 1" x 1/2" (QQPT553FX)	1" x 1" x 3/4" (QQPT554FX)
Street Elbow
1/2" x 3/8" (QQPE32BTX)
Swivel Adapter
3/8" x 1/2" (QQPSFC23X)	1/2" x 1/2" (QQPSFC33X)	3/4" x 3/4" (QQPSFC44X)	3/4" x 1" (QQPSFC45X)
1" x 1" (QQPSFC55X)
Swivel Elbow
1/2" x 1/2" (QQPE33BSX)	3/4" x 3/4" (QQPE44BSX)
Tee
1/2" x 1/2" x 1/2" (QQPT333X)	1/2" x 1/2" x 3/4" (QQPT334X)	3/4" x 1/2" x 1/2" (QQPT433X)	3/4" x 1/2" x 3/4" (QQPT434FX)
3/4" x 3/4" x 1/2" (QQPT443FX)	3/4" x 3/4" x 3/4" (QQPT444FX)	3/4" x 3/4" x 1" (QQPT445FX)	1" x 3/4" x 3/4" (QQPT544X)
1" x 1" x 1/2" (QQPT553FX)	1" x 1" x 3/4" (QQPT554FX)	1" x 1" x 1" (QQPT555FX)
* The letter Q is acceptable to be used on fittings due to size constraints. ¢ Product is authorized to bear the cNSF and/or the cNSFus Mark. § Product is Certified to the Uniform Plumbing Code™. Installation in accordance with the manufacturer's instructions and the requirements of the latest edition of the Uniform Plumbing Code™. +++ Material complies with NSF/ANSI/CAN 61 health effects requirements when tested at temperatures up to and including Commercial Hot (180° F). [G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state laws and the U.S. Safe Drinking Water Act.
Misc. Proc. Devices/Comp.& +++ [G]*	MLTPL	Qicksert QPBV2X	ASTM F877
1/2" Barb x 1/2" Swivel Qickport Manifold Valve
& Certified as a component of a manifold with a maximum of 21 valves per liter for hot applications and a maximum of 27 valves per liter for cold applications. * The letter Q is acceptable to be used on fittings due to size constraints. +++ Material complies with NSF/ANSI/CAN 61 health effects requirements when tested at temperatures up to and including Commercial Hot (180° F). [G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state laws and the U.S. Safe Drinking Water Act.
Misc. Proc. Devices/Comp.& +++ [G]*	MLTPL	Qicksert QPBV2X	ASTM F2159
1/2" Barb x 1/2" Swivel Qickport Manifold Valve
& Certified as a component of a manifold with a maximum of 21 valves per liter for hot applications and a maximum of 27 valves per liter for cold applications. * The letter Q is acceptable to be used on fittings due to size constraints. +++ Material complies with NSF/ANSI/CAN 61 health effects requirements when tested at temperatures up to and including Commercial Hot (180° F). [G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state laws and the U.S. Safe Drinking Water Act.
Misc. Proc. Devices/Comp.& +++ [G]*	MLTPL	Qicksert QPBV2X	CSA B137.5
1/2" Barb x 1/2" Swivel Qickport Manifold Valve
& Certified as a component of a manifold with a maximum of 21 valves per liter for hot applications and a maximum of 27 valves per liter for cold applications. * The letter Q is acceptable to be used on fittings due to size constraints. +++ Material complies with NSF/ANSI/CAN 61 health effects requirements when tested at temperatures up to and including Commercial Hot (180° F). [G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state laws and the U.S. Safe Drinking Water Act.
Misc. Proc. Devices/Comp.& ++ [G]*	MLTPL	Qicksert QPBV3X	ASTM F877
1/2" Barb x 1/2" Swivel QickPort Manifold Valve
& Certified as a component of a manifold with a maximum of 21 valves per liter for hot applications and a maximum of 27 valves per liter for cold applications. * The letter Q is acceptable to be used on fittings due to size constraints. ++ Material complies with NSF/ANSI/CAN 61 health effects requirements when tested at temperatures up to and including Domestic Hot (140° F). [G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state laws and the U.S. Safe Drinking Water Act.
Misc. Proc. Devices/Comp.& +++ [G]*	MLTPL	Qicksert QPBV3X	ASTM F877
1/2" Barb x 1/2" Swivel Qickport Manifold Valve
& Certified as a component of a manifold with a maximum of 21 valves per liter for hot applications and a maximum of 27 valves per liter for cold applications. * The letter Q is acceptable to be used on fittings due to size constraints. +++ Material complies with NSF/ANSI/CAN 61 health effects requirements when tested at temperatures up to and including Commercial Hot (180° F). [G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state laws and the U.S. Safe Drinking Water Act.
Misc. Proc. Devices/Comp.& +++ [G]*	MLTPL	Qicksert QPBV3X	ASTM F2159
1/2" Barb x 1/2" Swivel Qickport Manifold Valve
& Certified as a component of a manifold with a maximum of 21 valves per liter for hot applications and a maximum of 27 valves per liter for cold applications. * The letter Q is acceptable to be used on fittings due to size constraints. +++ Material complies with NSF/ANSI/CAN 61 health effects requirements when tested at temperatures up to and including Commercial Hot (180° F). [G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state laws and the U.S. Safe Drinking Water Act.
Misc. Proc. Devices/Comp.& +++ [G]*	MLTPL	Qicksert QPBV3X	CSA B137.5
1/2" Barb x 1/2" Swivel Qickport Manifold Valve
& Certified as a component of a manifold with a maximum of 21 valves per liter for hot applications and a maximum of 27 valves per liter for cold applications. * The letter Q is acceptable to be used on fittings due to size constraints. +++ Material complies with NSF/ANSI/CAN 61 health effects requirements when tested at temperatures up to and including Commercial Hot (180° F). [G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state laws and the U.S. Safe Drinking Water Act.
Manifolds¢ § +++ [G]	MLTPL	QKIPSP	ASTM F877
1" MPT x 1/2" MPT
¢ Product is authorized to bear the cNSF and/or the cNSFus Mark. § Product is Certified to the Uniform Plumbing Code™. Installation in accordance with the manufacturer's instructions and the requirements of the latest edition of the Uniform Plumbing Code™. +++ Material complies with NSF/ANSI/CAN 61 health effects requirements when tested at temperatures up to and including Commercial Hot (180° F). [G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state laws and the U.S. Safe Drinking Water Act.
Manifolds¢ § +++ [G]	MLTPL	QKIPSP	CSA B137.5
1" MPT x 1/2" MPT
¢ Product is authorized to bear the cNSF and/or the cNSFus Mark. § Product is Certified to the Uniform Plumbing Code™. Installation in accordance with the manufacturer's instructions and the requirements of the latest edition of the Uniform Plumbing Code™. +++ Material complies with NSF/ANSI/CAN 61 health effects requirements when tested at temperatures up to and including Commercial Hot (180° F). [G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state laws and the U.S. Safe Drinking Water Act.
Manifolds¢ § +++ [G]	MLTPL	QPPM10	ASTM F877
1" MPT x 1/2" MPT
¢ Product is authorized to bear the cNSF and/or the cNSFus Mark. § Product is Certified to the Uniform Plumbing Code™. Installation in accordance with the manufacturer's instructions and the requirements of the latest edition of the Uniform Plumbing Code™. +++ Material complies with NSF/ANSI/CAN 61 health effects requirements when tested at temperatures up to and including Commercial Hot (180° F). [G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state laws and the U.S. Safe Drinking Water Act.
Manifolds¢ +++ [G]	MLTPL	QPPM10	CSA B137.5
1" MPT x 1/2" MPT
¢ Product is authorized to bear the cNSF and/or the cNSFus Mark. +++ Material complies with NSF/ANSI/CAN 61 health effects requirements when tested at temperatures up to and including Commercial Hot (180° F). [G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state laws and the U.S. Safe Drinking Water Act.
Manifolds¢ § +++ [G]	MLTPL	QPPM20	ASTM F877
1" MPT x 1/2" MPT
¢ Product is authorized to bear the cNSF and/or the cNSFus Mark. § Product is Certified to the Uniform Plumbing Code™. Installation in accordance with the manufacturer's instructions and the requirements of the latest edition of the Uniform Plumbing Code™. +++ Material complies with NSF/ANSI/CAN 61 health effects requirements when tested at temperatures up to and including Commercial Hot (180° F). [G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state laws and the U.S. Safe Drinking Water Act.
Manifolds¢ +++ [G]	MLTPL	QPPM20	CSA B137.5
1" MPT x 1/2" MPT
¢ Product is authorized to bear the cNSF and/or the cNSFus Mark. +++ Material complies with NSF/ANSI/CAN 61 health effects requirements when tested at temperatures up to and including Commercial Hot (180° F). [G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state laws and the U.S. Safe Drinking Water Act.
Manifolds¢ § +++ [G]	MLTPL	QPPM3H9C	ASTM F877
1" MPT x 1/2" MPT
¢ Product is authorized to bear the cNSF and/or the cNSFus Mark. § Product is Certified to the Uniform Plumbing Code™. Installation in accordance with the manufacturer's instructions and the requirements of the latest edition of the Uniform Plumbing Code™. +++ Material complies with NSF/ANSI/CAN 61 health effects requirements when tested at temperatures up to and including Commercial Hot (180° F). [G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state laws and the U.S. Safe Drinking Water Act.
Manifolds¢ +++ [G]	MLTPL	QPPM3H9C	CSA B137.5
1" MPT x 1/2" MPT
¢ Product is authorized to bear the cNSF and/or the cNSFus Mark. +++ Material complies with NSF/ANSI/CAN 61 health effects requirements when tested at temperatures up to and including Commercial Hot (180° F). [G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state laws and the U.S. Safe Drinking Water Act.
Manifolds¢ § +++ [G]	MLTPL	QPPM3H9C-3	ASTM F877
1" MPT x 1/2" MPT
¢ Product is authorized to bear the cNSF and/or the cNSFus Mark. § Product is Certified to the Uniform Plumbing Code™. Installation in accordance with the manufacturer's instructions and the requirements of the latest edition of the Uniform Plumbing Code™. +++ Material complies with NSF/ANSI/CAN 61 health effects requirements when tested at temperatures up to and including Commercial Hot (180° F). [G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state laws and the U.S. Safe Drinking Water Act.
Manifolds¢ § +++ [G]	MLTPL	QPPM3H9C-3	CSA B137.5
1" MPT x 1/2" MPT
¢ Product is authorized to bear the cNSF and/or the cNSFus Mark. § Product is Certified to the Uniform Plumbing Code™. Installation in accordance with the manufacturer's instructions and the requirements of the latest edition of the Uniform Plumbing Code™. +++ Material complies with NSF/ANSI/CAN 61 health effects requirements when tested at temperatures up to and including Commercial Hot (180° F). [G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state laws and the U.S. Safe Drinking Water Act.
Manifolds¢ § +++ [G]	MLTPL	QPPM6H12C	ASTM F877
1" MPT x 1/2" MPT
¢ Product is authorized to bear the cNSF and/or the cNSFus Mark. § Product is Certified to the Uniform Plumbing Code™. Installation in accordance with the manufacturer's instructions and the requirements of the latest edition of the Uniform Plumbing Code™. +++ Material complies with NSF/ANSI/CAN 61 health effects requirements when tested at temperatures up to and including Commercial Hot (180° F). [G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state laws and the U.S. Safe Drinking Water Act.
Manifolds¢ +++ [G]	MLTPL	QPPM6H12C	CSA B137.5
1" MPT x 1/2" MPT
¢ Product is authorized to bear the cNSF and/or the cNSFus Mark. +++ Material complies with NSF/ANSI/CAN 61 health effects requirements when tested at temperatures up to and including Commercial Hot (180° F). [G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state laws and the U.S. Safe Drinking Water Act.
Manifolds¢ +++ [G]	MLTPL	QPPM6H12C-3	ASTM F877
1" MPT x 1/2" MPT
¢ Product is authorized to bear the cNSF and/or the cNSFus Mark. +++ Material complies with NSF/ANSI/CAN 61 health effects requirements when tested at temperatures up to and including Commercial Hot (180° F). [G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state laws and the U.S. Safe Drinking Water Act.
Manifolds¢ +++ [G]	MLTPL	QPPM6H12C-3	CSA B137.5
1" MPT x 1/2" MPT
¢ Product is authorized to bear the cNSF and/or the cNSFus Mark. +++ Material complies with NSF/ANSI/CAN 61 health effects requirements when tested at temperatures up to and including Commercial Hot (180° F). [G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state laws and the U.S. Safe Drinking Water Act.
Manifolds¢ § +++ [G]	MLTPL	QPPM9H15C	ASTM F877
1" MPT x 1/2" MPT
¢ Product is authorized to bear the cNSF and/or the cNSFus Mark. § Product is Certified to the Uniform Plumbing Code™. Installation in accordance with the manufacturer's instructions and the requirements of the latest edition of the Uniform Plumbing Code™. +++ Material complies with NSF/ANSI/CAN 61 health effects requirements when tested at temperatures up to and including Commercial Hot (180° F). [G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state laws and the U.S. Safe Drinking Water Act.
Manifolds¢ +++ [G]	MLTPL	QPPM9H15C	CSA B137.5
1" MPT x 1/2" MPT
¢ Product is authorized to bear the cNSF and/or the cNSFus Mark. +++ Material complies with NSF/ANSI/CAN 61 health effects requirements when tested at temperatures up to and including Commercial Hot (180° F). [G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state laws and the U.S. Safe Drinking Water Act.
Manifolds¢ +++ [G]	MLTPL	QPPM9H15C-3	ASTM F877
1" MPT x 1/2" MPT
¢ Product is authorized to bear the cNSF and/or the cNSFus Mark. +++ Material complies with NSF/ANSI/CAN 61 health effects requirements when tested at temperatures up to and including Commercial Hot (180° F). [G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state laws and the U.S. Safe Drinking Water Act.
Manifolds¢ +++ [G]	MLTPL	QPPM9H15C-3	CSA B137.5
1" MPT x 1/2" MPT
¢ Product is authorized to bear the cNSF and/or the cNSFus Mark. +++ Material complies with NSF/ANSI/CAN 61 health effects requirements when tested at temperatures up to and including Commercial Hot (180° F). [G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state laws and the U.S. Safe Drinking Water Act.
Manifolds¢ +++ [G]	MLTPL	QPPM10-3	ASTM F877
1" MPT x 1/2" MPT
¢ Product is authorized to bear the cNSF and/or the cNSFus Mark. +++ Material complies with NSF/ANSI/CAN 61 health effects requirements when tested at temperatures up to and including Commercial Hot (180° F). [G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state laws and the U.S. Safe Drinking Water Act.
Manifolds¢ +++ [G]	MLTPL	QPPM10-3	CSA B137.5
1" MPT x 1/2" MPT
¢ Product is authorized to bear the cNSF and/or the cNSFus Mark. +++ Material complies with NSF/ANSI/CAN 61 health effects requirements when tested at temperatures up to and including Commercial Hot (180° F). [G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state laws and the U.S. Safe Drinking Water Act.
Manifolds¢ +++ [G]	MLTPL	QPPM20-3	ASTM F877
1" MPT x 1/2" MPT
¢ Product is authorized to bear the cNSF and/or the cNSFus Mark. +++ Material complies with NSF/ANSI/CAN 61 health effects requirements when tested at temperatures up to and including Commercial Hot (180° F). [G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state laws and the U.S. Safe Drinking Water Act.
Manifolds¢ +++ [G]	MLTPL	QPPM20-3	CSA B137.5
1" MPT x 1/2" MPT
¢ Product is authorized to bear the cNSF and/or the cNSFus Mark. +++ Material complies with NSF/ANSI/CAN 61 health effects requirements when tested at temperatures up to and including Commercial Hot (180° F). [G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state laws and the U.S. Safe Drinking Water Act.
Manifolds¢ § +++ [G]	MLTPL	QPPM12H18C	ASTM F877
1" MPT x 1/2" MPT
¢ Product is authorized to bear the cNSF and/or the cNSFus Mark. § Product is Certified to the Uniform Plumbing Code™. Installation in accordance with the manufacturer's instructions and the requirements of the latest edition of the Uniform Plumbing Code™. +++ Material complies with NSF/ANSI/CAN 61 health effects requirements when tested at temperatures up to and including Commercial Hot (180° F). [G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state laws and the U.S. Safe Drinking Water Act.
Manifolds¢ +++ [G]	MLTPL	QPPM12H18C	CSA B137.5
1" MPT x 1/2" MPT
¢ Product is authorized to bear the cNSF and/or the cNSFus Mark. +++ Material complies with NSF/ANSI/CAN 61 health effects requirements when tested at temperatures up to and including Commercial Hot (180° F). [G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state laws and the U.S. Safe Drinking Water Act.
Manifolds¢ § +++ [G]	MLTPL	QPPM18H18C6NS	ASTM F877
1" MPT x 1/2" MPT
¢ Product is authorized to bear the cNSF and/or the cNSFus Mark. § Product is Certified to the Uniform Plumbing Code™. Installation in accordance with the manufacturer's instructions and the requirements of the latest edition of the Uniform Plumbing Code™. +++ Material complies with NSF/ANSI/CAN 61 health effects requirements when tested at temperatures up to and including Commercial Hot (180° F). [G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state laws and the U.S. Safe Drinking Water Act.
Manifolds¢ § +++ [G]	MLTPL	QPPM18H18C6NS	CSA B137.5
1" MPT x 1/2" MPT
¢ Product is authorized to bear the cNSF and/or the cNSFus Mark. § Product is Certified to the Uniform Plumbing Code™. Installation in accordance with the manufacturer's instructions and the requirements of the latest edition of the Uniform Plumbing Code™. +++ Material complies with NSF/ANSI/CAN 61 health effects requirements when tested at temperatures up to and including Commercial Hot (180° F). [G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state laws and the U.S. Safe Drinking Water Act.
Manifolds¢ § +++ [G]	MLTPL	QPPM15H21C	ASTM F877
1" MPT x 1/2" MPT
¢ Product is authorized to bear the cNSF and/or the cNSFus Mark. § Product is Certified to the Uniform Plumbing Code™. Installation in accordance with the manufacturer's instructions and the requirements of the latest edition of the Uniform Plumbing Code™. +++ Material complies with NSF/ANSI/CAN 61 health effects requirements when tested at temperatures up to and including Commercial Hot (180° F). [G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state laws and the U.S. Safe Drinking Water Act.
Manifolds¢ +++ [G]	MLTPL	QPPM15H21C	CSA B137.5
1" MPT x 1/2" MPT
¢ Product is authorized to bear the cNSF and/or the cNSFus Mark. +++ Material complies with NSF/ANSI/CAN 61 health effects requirements when tested at temperatures up to and including Commercial Hot (180° F). [G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state laws and the U.S. Safe Drinking Water Act.
Manifolds¢ § +++ [G]	MLTPL	QPPM18H24C	ASTM F877
1" MPT x 1/2" MPT
¢ Product is authorized to bear the cNSF and/or the cNSFus Mark. § Product is Certified to the Uniform Plumbing Code™. Installation in accordance with the manufacturer's instructions and the requirements of the latest edition of the Uniform Plumbing Code™. +++ Material complies with NSF/ANSI/CAN 61 health effects requirements when tested at temperatures up to and including Commercial Hot (180° F). [G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state laws and the U.S. Safe Drinking Water Act.
Manifolds¢ +++ [G]	MLTPL	QPPM18H24C	CSA B137.5
1" MPT x 1/2" MPT
¢ Product is authorized to bear the cNSF and/or the cNSFus Mark. +++ Material complies with NSF/ANSI/CAN 61 health effects requirements when tested at temperatures up to and including Commercial Hot (180° F). [G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state laws and the U.S. Safe Drinking Water Act.
Manifolds¢ +++ [G]	MLTPL	QPPM18H24C-3	ASTM F877
1" MPT x 1/2" MPT
¢ Product is authorized to bear the cNSF and/or the cNSFus Mark. +++ Material complies with NSF/ANSI/CAN 61 health effects requirements when tested at temperatures up to and including Commercial Hot (180° F). [G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state laws and the U.S. Safe Drinking Water Act.
Manifolds¢ +++ [G]	MLTPL	QPPM18H24C-3	CSA B137.5
1" MPT x 1/2" MPT
¢ Product is authorized to bear the cNSF and/or the cNSFus Mark. +++ Material complies with NSF/ANSI/CAN 61 health effects requirements when tested at temperatures up to and including Commercial Hot (180° F). [G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state laws and the U.S. Safe Drinking Water Act.
Manifolds¢ +++ [G]	MLTPL	QPPM9H9C6NS	ASTM F877
1" MPT x 1/2" MPT
¢ Product is authorized to bear the cNSF and/or the cNSFus Mark. +++ Material complies with NSF/ANSI/CAN 61 health effects requirements when tested at temperatures up to and including Commercial Hot (180° F). [G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state laws and the U.S. Safe Drinking Water Act.
Manifolds¢ +++ [G]	MLTPL	QPPM9H9C6NS	CSA B137.5
1" MPT x 1/2" MPT
¢ Product is authorized to bear the cNSF and/or the cNSFus Mark. +++ Material complies with NSF/ANSI/CAN 61 health effects requirements when tested at temperatures up to and including Commercial Hot (180° F). [G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state laws and the U.S. Safe Drinking Water Act.
Manifolds¢ +++ [G]	MLTPL	QPPM9H9C6NS-3	ASTM F877
1" MPT x 1/2" MPT
¢ Product is authorized to bear the cNSF and/or the cNSFus Mark. +++ Material complies with NSF/ANSI/CAN 61 health effects requirements when tested at temperatures up to and including Commercial Hot (180° F). [G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state laws and the U.S. Safe Drinking Water Act.
Manifolds¢ +++ [G]	MLTPL	QPPM9H9C6NS-3	CSA B137.5
1" MPT x 1/2" MPT
¢ Product is authorized to bear the cNSF and/or the cNSFus Mark. +++ Material complies with NSF/ANSI/CAN 61 health effects requirements when tested at temperatures up to and including Commercial Hot (180° F). [G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state laws and the U.S. Safe Drinking Water Act.
Manifolds¢ § +++ [G]	MLTPL	QPPM12H12C6NS	ASTM F877
1" MPT x 1/2" MPT
¢ Product is authorized to bear the cNSF and/or the cNSFus Mark. § Product is Certified to the Uniform Plumbing Code™. Installation in accordance with the manufacturer's instructions and the requirements of the latest edition of the Uniform Plumbing Code™. +++ Material complies with NSF/ANSI/CAN 61 health effects requirements when tested at temperatures up to and including Commercial Hot (180° F). [G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state laws and the U.S. Safe Drinking Water Act.
Manifolds¢ +++ [G]	MLTPL	QPPM12H12C6NS	CSA B137.5
1" MPT x 1/2" MPT
¢ Product is authorized to bear the cNSF and/or the cNSFus Mark. +++ Material complies with NSF/ANSI/CAN 61 health effects requirements when tested at temperatures up to and including Commercial Hot (180° F). [G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state laws and the U.S. Safe Drinking Water Act.
Manifolds¢ +++ [G]	MLTPL	QPPM12H12C6NS-3	ASTM F877
1" MPT x 1/2" MPT
¢ Product is authorized to bear the cNSF and/or the cNSFus Mark. +++ Material complies with NSF/ANSI/CAN 61 health effects requirements when tested at temperatures up to and including Commercial Hot (180° F). [G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state laws and the U.S. Safe Drinking Water Act.
Manifolds¢ +++ [G]	MLTPL	QPPM12H12C6NS-3	CSA B137.5
1" MPT x 1/2" MPT
¢ Product is authorized to bear the cNSF and/or the cNSFus Mark. +++ Material complies with NSF/ANSI/CAN 61 health effects requirements when tested at temperatures up to and including Commercial Hot (180° F). [G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state laws and the U.S. Safe Drinking Water Act.
Manifolds¢ § +++ [G]	MLTPL	QPPM15H15C6NS	ASTM F877
1" MPT x 1/2" MPT
¢ Product is authorized to bear the cNSF and/or the cNSFus Mark. § Product is Certified to the Uniform Plumbing Code™. Installation in accordance with the manufacturer's instructions and the requirements of the latest edition of the Uniform Plumbing Code™. +++ Material complies with NSF/ANSI/CAN 61 health effects requirements when tested at temperatures up to and including Commercial Hot (180° F). [G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state laws and the U.S. Safe Drinking Water Act.
Manifolds¢ +++ [G]	MLTPL	QPPM15H15C6NS	CSA B137.5
1" MPT x 1/2" MPT
¢ Product is authorized to bear the cNSF and/or the cNSFus Mark. +++ Material complies with NSF/ANSI/CAN 61 health effects requirements when tested at temperatures up to and including Commercial Hot (180° F). [G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state laws and the U.S. Safe Drinking Water Act.
Manifolds¢ +++ [G]	MLTPL	QPPM15H15C6NS-3	ASTM F877
1" MPT x 1/2" MPT
¢ Product is authorized to bear the cNSF and/or the cNSFus Mark. +++ Material complies with NSF/ANSI/CAN 61 health effects requirements when tested at temperatures up to and including Commercial Hot (180° F). [G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state laws and the U.S. Safe Drinking Water Act.
Manifolds¢ +++ [G]	MLTPL	QPPM15H15C6NS-3	CSA B137.5
1" MPT x 1/2" MPT
¢ Product is authorized to bear the cNSF and/or the cNSFus Mark. +++ Material complies with NSF/ANSI/CAN 61 health effects requirements when tested at temperatures up to and including Commercial Hot (180° F). [G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state laws and the U.S. Safe Drinking Water Act.
Manifolds¢ +++ [G]	MLTPL	QPPM15H21C-3	ASTM F877
1" MPT x 1/2" MPT
¢ Product is authorized to bear the cNSF and/or the cNSFus Mark. +++ Material complies with NSF/ANSI/CAN 61 health effects requirements when tested at temperatures up to and including Commercial Hot (180° F). [G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state laws and the U.S. Safe Drinking Water Act.
Manifolds¢ +++ [G]	MLTPL	QPPM15H21C-3	CSA B137.5
1" MPT x 1/2" MPT
¢ Product is authorized to bear the cNSF and/or the cNSFus Mark. +++ Material complies with NSF/ANSI/CAN 61 health effects requirements when tested at temperatures up to and including Commercial Hot (180° F). [G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state laws and the U.S. Safe Drinking Water Act.
Manifolds¢ § +++ [G]	MLTPL	QPPM12H18C-3	ASTM F877
1" MPT x 1/2" MPT
¢ Product is authorized to bear the cNSF and/or the cNSFus Mark. § Product is Certified to the Uniform Plumbing Code™. Installation in accordance with the manufacturer's instructions and the requirements of the latest edition of the Uniform Plumbing Code™. +++ Material complies with NSF/ANSI/CAN 61 health effects requirements when tested at temperatures up to and including Commercial Hot (180° F). [G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state laws and the U.S. Safe Drinking Water Act.
Manifolds¢ +++ [G]	MLTPL	QPPM12H18C-3	CSA B137.5
1" MPT x 1/2" MPT
¢ Product is authorized to bear the cNSF and/or the cNSFus Mark. +++ Material complies with NSF/ANSI/CAN 61 health effects requirements when tested at temperatures up to and including Commercial Hot (180° F). [G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state laws and the U.S. Safe Drinking Water Act.
Manifolds¢ § +++ [G]	MLTPL	QPPM18H18C6NS-3	ASTM F877
1" MPT x 1/2" MPT
¢ Product is authorized to bear the cNSF and/or the cNSFus Mark. § Product is Certified to the Uniform Plumbing Code™. Installation in accordance with the manufacturer's instructions and the requirements of the latest edition of the Uniform Plumbing Code™. +++ Material complies with NSF/ANSI/CAN 61 health effects requirements when tested at temperatures up to and including Commercial Hot (180° F). [G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state laws and the U.S. Safe Drinking Water Act.
Manifolds¢ § +++ [G]	MLTPL	QPPM18H18C6NS-3	CSA B137.5
1" MPT x 1/2" MPT
¢ Product is authorized to bear the cNSF and/or the cNSFus Mark. § Product is Certified to the Uniform Plumbing Code™. Installation in accordance with the manufacturer's instructions and the requirements of the latest edition of the Uniform Plumbing Code™. +++ Material complies with NSF/ANSI/CAN 61 health effects requirements when tested at temperatures up to and including Commercial Hot (180° F). [G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state laws and the U.S. Safe Drinking Water Act.
Manifolds¢ +++ [G]	MLTPL	QPPM21H21C6NS	ASTM F877
1" MPT x 1/2" MPT
¢ Product is authorized to bear the cNSF and/or the cNSFus Mark. +++ Material complies with NSF/ANSI/CAN 61 health effects requirements when tested at temperatures up to and including Commercial Hot (180° F). [G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state laws and the U.S. Safe Drinking Water Act.
Manifolds¢ +++ [G]	MLTPL	QPPM21H21C6NS	CSA B137.5
1" MPT x 1/2" MPT
¢ Product is authorized to bear the cNSF and/or the cNSFus Mark. +++ Material complies with NSF/ANSI/CAN 61 health effects requirements when tested at temperatures up to and including Commercial Hot (180° F). [G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state laws and the U.S. Safe Drinking Water Act.
Manifolds¢ § +++ [G]	MLTPL	QPPM21H21C6NS-3	ASTM F877
1" MPT x 1/2" MPT
¢ Product is authorized to bear the cNSF and/or the cNSFus Mark. § Product is Certified to the Uniform Plumbing Code™. Installation in accordance with the manufacturer's instructions and the requirements of the latest edition of the Uniform Plumbing Code™. +++ Material complies with NSF/ANSI/CAN 61 health effects requirements when tested at temperatures up to and including Commercial Hot (180° F). [G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state laws and the U.S. Safe Drinking Water Act.
Manifolds¢ § +++ [G]	MLTPL	QPPM21H21C6NS-3	CSA B137.5
1" MPT x 1/2" MPT
¢ Product is authorized to bear the cNSF and/or the cNSFus Mark. § Product is Certified to the Uniform Plumbing Code™. Installation in accordance with the manufacturer's instructions and the requirements of the latest edition of the Uniform Plumbing Code™. +++ Material complies with NSF/ANSI/CAN 61 health effects requirements when tested at temperatures up to and including Commercial Hot (180° F). [G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state laws and the U.S. Safe Drinking Water Act.
Tubing# ^ ¢ § +++ [G]	PEX 5306	WarmPex - Red	ASTM F876/F877
1/8" - 2"
# Tubing certified against CSA B137.5 shall include the standard designation(s) of the fitting system(s) for which the tubing is recommended by the manufacturer, and shall be marked, as applicable, with the following fitting system designation(s): ASTM F1807, ASTM F2159, ASTM F1960, ASTM F2098 and ASTM F876/F877. ^ Meets the chlorine resistance requirements of ASTM F876 when tested in accordance with ASTM 2023. ¢ Product is authorized to bear the cNSF and/or the cNSFus Mark. § Product is Certified to the Uniform Plumbing Code™. Installation in accordance with the manufacturer's instructions and the requirements of the latest edition of the Uniform Plumbing Code™. +++ Material complies with NSF/ANSI/CAN 61 health effects requirements when tested at temperatures up to and including Commercial Hot (180° F). [G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state laws and the U.S. Safe Drinking Water Act.
Tubing^ ¢ § +++ [G]	PEX 5306	WarmPex - Red	AWWA C904
1/2" - 2"
^ Meets the chlorine resistance requirements of ASTM F876 when tested in accordance with ASTM 2023. ¢ Product is authorized to bear the cNSF and/or the cNSFus Mark. § Product is Certified to the Uniform Plumbing Code™. Installation in accordance with the manufacturer's instructions and the requirements of the latest edition of the Uniform Plumbing Code™. +++ Material complies with NSF/ANSI/CAN 61 health effects requirements when tested at temperatures up to and including Commercial Hot (180° F). [G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state laws and the U.S. Safe Drinking Water Act.
Tubing# ^ ¢ § +++ [G]	PEX	WarmPex - Red	CSA B137.5
1/8" - 2"
# Tubing certified against CSA B137.5 shall include the standard designation(s) of the fitting system(s) for which the tubing is recommended by the manufacturer, and shall be marked, as applicable, with the following fitting system designation(s): ASTM F1807, ASTM F2159, ASTM F1960, ASTM F2098 and ASTM F876/F877. ^ Meets the chlorine resistance requirements of ASTM F876 when tested in accordance with ASTM 2023. ¢ Product is authorized to bear the cNSF and/or the cNSFus Mark. § Product is Certified to the Uniform Plumbing Code™. Installation in accordance with the manufacturer's instructions and the requirements of the latest edition of the Uniform Plumbing Code™. +++ Material complies with NSF/ANSI/CAN 61 health effects requirements when tested at temperatures up to and including Commercial Hot (180° F). [G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state laws and the U.S. Safe Drinking Water Act.
Tubing# ^ ¢ § +++ [G]	PEX 5306	ZURNPEX - Blue, Red, White	ASTM F876/F877
1/8" - 2"
# Tubing certified against CSA B137.5 shall include the standard designation(s) of the fitting system(s) for which the tubing is recommended by the manufacturer, and shall be marked, as applicable, with the following fitting system designation(s): ASTM F1807, ASTM F2159, ASTM F1960, ASTM F2098 and ASTM F876/F877. ^ Meets the chlorine resistance requirements of ASTM F876 when tested in accordance with ASTM 2023. ¢ Product is authorized to bear the cNSF and/or the cNSFus Mark. § Product is Certified to the Uniform Plumbing Code™. Installation in accordance with the manufacturer's instructions and the requirements of the latest edition of the Uniform Plumbing Code™. +++ Material complies with NSF/ANSI/CAN 61 health effects requirements when tested at temperatures up to and including Commercial Hot (180° F). [G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state laws and the U.S. Safe Drinking Water Act.
Tubing^ ¢ § +++ [G]	PEX 5306	ZURNPEX - Blue, Red, White	AWWA C904
1/2" - 2"
^ Meets the chlorine resistance requirements of ASTM F876 when tested in accordance with ASTM 2023. ¢ Product is authorized to bear the cNSF and/or the cNSFus Mark. § Product is Certified to the Uniform Plumbing Code™. Installation in accordance with the manufacturer's instructions and the requirements of the latest edition of the Uniform Plumbing Code™. +++ Material complies with NSF/ANSI/CAN 61 health effects requirements when tested at temperatures up to and including Commercial Hot (180° F). [G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state laws and the U.S. Safe Drinking Water Act.
Tubing# ^ ¢ § +++ [G]	PEX	ZURNPEX - Blue, Red, White	CSA B137.5
1/8" - 2"
# Tubing certified against CSA B137.5 shall include the standard designation(s) of the fitting system(s) for which the tubing is recommended by the manufacturer, and shall be marked, as applicable, with the following fitting system designation(s): ASTM F1807, ASTM F2159, ASTM F1960, ASTM F2098 and ASTM F876/F877. ^ Meets the chlorine resistance requirements of ASTM F876 when tested in accordance with ASTM 2023. ¢ Product is authorized to bear the cNSF and/or the cNSFus Mark. § Product is Certified to the Uniform Plumbing Code™. Installation in accordance with the manufacturer's instructions and the requirements of the latest edition of the Uniform Plumbing Code™. +++ Material complies with NSF/ANSI/CAN 61 health effects requirements when tested at temperatures up to and including Commercial Hot (180° F). [G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state laws and the U.S. Safe Drinking Water Act.

Radiant Floor Heating

Product Type	Material Type	Trade Name	Product Standard
Tubing#	PEX 0006	ACCUTEK PEX - Blue, Natural, Red, White	*SE 8221*
3/8" - 1"
# Pipe Certified as a system using QEST®PEX fittings manufactured by ZurnPex Inc. Installation/assembly instructions titled "QEST®PEX Professional PEX Plumbing System Installation Guide", dated September 1995.
Tubing#	PEX 0006	QEST®PEX Hydronic Barrier-Blue, Red, Natural	*SE 8221*
3/8" - 1"
# Pipe Certified as a system using QEST®PEX fittings manufactured by ZurnPex Inc. Installation/assembly instructions titled "QEST®PEX Professional PEX Plumbing System Installation Guide", dated September 1995.
Tubing#	PEX 0006	Slant/Fin Terra Therma	*SE 8221*
3/8" - 1"
# Pipe Certified as a system using QEST®PEX fittings manufactured by ZurnPex Inc. Installation/assembly instructions titled "QEST®PEX Professional PEX Plumbing System Installation Guide", dated September 1995.
Tubing#	PEX 0006	WarmPex - Red	*SE 8221*
3/8" - 1"
# Pipe Certified as a system using QEST®PEX fittings manufactured by ZurnPex Inc. Installation/assembly instructions titled "QEST®PEX Professional PEX Plumbing System Installation Guide", dated September 1995.
Tubing#	PEX 0006	ZURNPEX Hydronic Barrier - Blue, Red, Natural	*SE 8221*
3/8" - 1"
# Pipe Certified as a system using QEST®PEX fittings manufactured by ZurnPex Inc. Installation/assembly instructions titled "QEST®PEX Professional PEX Plumbing System Installation Guide", dated September 1995.
Tubing#	PEX 0006	Zurn PEX Performa	*SE 8221*
3/8" - 1"
# Pipe Certified as a system using QEST®PEX fittings manufactured by ZurnPex Inc. Installation/assembly instructions titled "QEST®PEX Professional PEX Plumbing System Installation Guide", dated September 1995.

NSF/ANSI 24
Plumbing System Components for Recreational Vehicles

Shell Chemical Appalachia LLC
P.O. Box 4749
Houston, TX 77210-4749
United States
724-709-2268

Facility : Monaca, PA

Potable Water Materials for Recreational Vehicles
35R5U - Medium-Density Polyethylene Resin* ++	35R5U.DEV - Medium-Density Polyethylene Resin* ++	35R7U - Medium-Density Polyethylene Resin* ++	39R4U - Medium-Density Polyethylene Resin* ++
39R4U.DEV Medium-Density Polyethylene Resin* ++
Tank Materials for Recreational Vehicles
35R5U - Medium-Density Polyethylene Resin** ++	35R5U.DEV - Medium-Density Polyethylene Resin** ++	35R7U - Medium-Density Polyethylene Resin** ++	39R4U - Medium-Density Polyethylene Resin** ++
39R4U.DEV Medium-Density Polyethylene Resin* ++
* Certified for pipe, fitting and appurtenance end use. ++ Material complies with NSF/ANSI/CAN 61 health effects requirements when tested at temperatures up to and including Domestic Hot (140° F). * Certified for pipe, fitting and appurtenance end use. ** Certified for use in Tanks = 5 gal. ++ Material complies with NSF/ANSI/CAN 61 health effects requirements when tested at temperatures up to and including Domestic Hot (140° F).

MP
Mechanical Plumbing Products

Charlotte Pipe & Foundry Company
Plastics Division
4210 Old Charlotte Highway
P.O. Box 1339
Monroe, NC 28111-1339
United States
704-291-3218
Visit this company's website

Facility : Muncy, PA

Product Type	Material Type	Trade Name	Product Standard
Pipe	MLTPL	Charlotte Pipe®	CSA Z240.3.2
Pipe§	PVC	Charlotte Pipe®	CSA Z240.3.2
1 1/4" - 6" DR 24
§ Product is Certified to the Uniform Plumbing Code™. Installation in accordance with the manufacturer's instructions and the requirements of the latest edition of the Uniform Plumbing Code™.

Victaulic
4901 Kesslersville Road
Easton, PA 18040
United States
800-742-5842
610-559-3300
Visit this company's website

Facility : Easton, PA

Product Type	Material Type	Trade Name	Product Standard
Couplings[1]	Ductile Iron	Victaulic	ASTM F1476
Flexible Couplings
Style 77 (1" - 10")
Rigid Couplings
Style 07 (1" - 12")	Style 107H (2" - 8")	Style 607 (2" - 6")	Style 89 (2" - 12")
[1] Products rated to 300 psi.
Fittings[1]	Bronze	Victaulic	ASTM F1548
Endcaps
No. 660 (2" - 6")
[1] Products rated to 300 psi.
Fittings[1]	Copper	Victaulic	ASTM F1548
Reducing Tee
No. 625 (3" x 2" - 4" x 3")
Tee
No. 620 (2" - 6")
[1] Products rated to 300 psi.
Fittings[1]	Ductile Iron	Victaulic	ASTM F1548
11 1/4° Elbow
No. 13 (2 1/2")
45° Elbow
No. 11 (1 1/2" - 12")
90° Elbow
No. 10 (1 1/2" - 12")
90° w/Drain Elbow
No. 10DR (3" - 6")
Copper Elbow
No. 610 (2 1/2")
Dielectric Waterway
Style 47 (1" - 8")
End Cap
No. 60 (1" - 12")
Flange Adapter
Style 641 (2" - 6")	Style 741 (2 1/2" - 12")
Reducer
No. 50 (2" x 1 1/2" - 10" x 8")
Reducer Tee
No. 25 (10" x 8" - 12" x 10")	No. 25 (2 1/2" x 1" - 10" x 6")
Tee
No. 20 (2 1/2" - 10")
[1] Products rated to 300 psi.
Fittings	SS	Victaulic	ASTM F1548
45º Elbow[1]
No. 411 (2" - 12")
90º Elbow[1]
No. 410 (2" - 12")
Concentric Reducer[1]
No. 450 (2" x 1 1/2" - 12" x 10")
End Cap[1]
No. 460 (2" - 12")
Reducing Tee[1]
No. 425 (2" x 1 1/2" - 12" x 10")
Tee[2]
No. 420 (2" - 12")
[1] Products rated to 300 psi. [2] Products rated to 150 psi.

Facility : Easton, PA

Product Type	Material Type	Trade Name	Product Standard
Couplings[1]	Ductile Iron	Victaulic	ASTM F1476
Flexible Couplings
Style 77 (1" - 10")
Rigid Couplings
Style 07 (1" - 12")	Style 107H (2" - 8")	Style 607 (2" - 6")	Style 89 (2" - 12")
[1] Products rated to 300 psi.
Fittings[1]	Bronze	Victaulic	ASTM F1548
Endcaps
No. 660 (2" - 6")
[1] Products rated to 300 psi.
Fittings[1]	Copper	Victaulic	ASTM F1548
Reducing Tee
No. 625 (3" x 2" - 4" x 3")
Tee
No. 620 (2" - 6")
[1] Products rated to 300 psi.
Fittings[1]	Ductile Iron	Victaulic	ASTM F1548
11 1/4° Elbow
No. 13 (2 1/2")
45° Elbow
No. 11 (1 1/2" - 12")
90° Elbow
No. 10 (1 1/2" - 12")
90° w/Drain Elbow
No. 10DR (3" - 6")
Copper Elbow
No. 610 (2 1/2")
Dielectric Waterway
Style 47 (1" - 8")
End Cap
No. 60 (1" - 12")
Flange Adapter
Style 641 (2" - 6")	Style 741 (2 1/2" - 12")
Reducer
No. 50 (2" x 1 1/2" - 10" x 8")
Reducer Tee
No. 25 (10" x 8" - 12" x 10")	No. 25 (2 1/2" x 1" - 10" x 6")
Tee
No. 20 (2 1/2" - 10")
[1] Products rated to 300 psi.
Fittings	SS	Victaulic	ASTM F1548
45º Elbow[1]
No. 411 (2" - 12")
90º Elbow[1]
No. 410 (2" - 12")
Concentric Reducer[1]
No. 450 (2" x 1 1/2" - 12" x 10")
End Cap[1]
No. 460 (2" - 12")
Reducing Tee[1]
No. 425 (2" x 1 1/2" - 12" x 10")
Tee[2]
No. 420 (2" - 12")
[1] Products rated to 300 psi. [2] Products rated to 150 psi.

Zurn PEX, Inc.
116 Maple Street
Commerce, TX 75428
United States
903-886-2580
Visit this company's website

Facility : Harborcreek, PA

Product Type	Material Type	Trade Name	Product Standard
Misc. Proc. Devices/Comp.& +++ [G]*	MLTPL	Q	ASME A112.18.1/CSA B125.1
1/2" Barb x 1/2" Swivel Qickport Manifold Valve
& Certified as a component of a manifold with a maximum of 21 valves per liter for hot applications and a maximum of 27 valves per liter for cold applications. * The letter Q is acceptable to be used on fittings due to size constraints. +++ Material complies with NSF/ANSI/CAN 61 health effects requirements when tested at temperatures up to and including Commercial Hot (180° F). [G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state laws and the U.S. Safe Drinking Water Act.
Misc. Proc. Devices/Comp.& +++ [G]*	MLTPL	Qicksert QPPBV2X	ASME A112.18.1/CSA B125.1
1/2" Barb x 1/2" Swivel Qickport Manifold Valve
& Certified as a component of a manifold with a maximum of 21 valves per liter for hot applications and a maximum of 27 valves per liter for cold applications. * The letter Q is acceptable to be used on fittings due to size constraints. +++ Material complies with NSF/ANSI/CAN 61 health effects requirements when tested at temperatures up to and including Commercial Hot (180° F). [G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state laws and the U.S. Safe Drinking Water Act.
Misc. Proc. Devices/Comp.& +++ [G]*	MLTPL	Qicksert QPPBV3X	ASME A112.18.1/CSA B125.1
1/2" Barb x 1/2" Swivel Qickport Manifold Valve
& Certified as a component of a manifold with a maximum of 21 valves per liter for hot applications and a maximum of 27 valves per liter for cold applications. * The letter Q is acceptable to be used on fittings due to size constraints. +++ Material complies with NSF/ANSI/CAN 61 health effects requirements when tested at temperatures up to and including Commercial Hot (180° F). [G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state laws and the U.S. Safe Drinking Water Act.

NSF/ANSI 358
Water-Based Ground-Source “Geothermal” Heat Pump Systems

Georg Fischer Central Plastics LLC
4949 Joseph Hardin Drive
Dallas, TX 75236
United States
469-801-2246

Facility : Titusville, PA

NSF/ANSI 358-1 Polyethylene Pipe and Fittings

Product Type	Material Type	Trade Name	Product Standard
Pipe$ @	PE 4710	+GF+ DESIGN FLOW	ASTM D3035
3" DR 9, 11, 13.5, 15.5, 17
3/4" - 2" DR 9, 11
$ These products also meet the requirements for PE 3408 per ASTM D3350-02a. @ Certified product may include a fused U-bend fitting.
Pipe$ @	PE 4710	+GF+ DESIGN FLOW	ASTM F714
4" - 24" DR 9, 11, 13.5, 15.5, 17
$ These products also meet the requirements for PE 3408 per ASTM D3350-02a. @ Certified product may include a fused U-bend fitting.

WL Plastics Corporation
3575 Lone Star Circle
Suite 300
Fort Worth, TX 76177
United States
682-831-2727
Visit this company's website

Facility : Titusville, PA

NSF/ANSI 358-1 Polyethylene Pipe and Fittings

Product Type	Material Type	Trade Name	Product Standard
Pipe @*	PE 4710	WL Plastics PA/WLP PA Geothermal Pipe	ASTM D3035
1/2" DR 7[1]
3/4" - 3" DR 7
1/2" DR 9[1]
3/4" - 3" DR 9
1/2" - 3" DR 11[1]
1/2" - 3" DR 13.5[1]
3/4" - 3" DR 15.5[1]
3/4" - 3" DR 17[1]
1" - 3" DR 21[1]
1" - 3" DR 26[1]
1 1/2" - 3" DR 32.5[1]
[1] These pipe sizes are not certified for use in potable water applications containing oxidizing disinfectants and shall not be marked with a CC oxidative resistance classification. * These products also meet the requirements for PE 3408 per ASTM D3350-02a. @ Certified product may include a fused U-bend fitting.
Pipe @*	PE 4710	WL Plastics PA/WLP PA Geothermal Pipe	ASTM F714
4" - 18" IPS DR 7.3
4" - 26" IPS DR 7
4" - 36" IPS DR 9
4" - 42" IPS DR 11
4" - 48" IPS DR 13.5
4" - 54" IPS DR 15.5[2]
4" - 54" IPS DR 17
4" - 54" IPS DR 21
4" - 54" IPS DR 26
4" - 54" IPS DR 32.5
4" - 54" IPS DR 41
[2] Special sizes may be acceptable for engineered applications, due to system conditions or special local requirements. It is the responsibility of the end user to ensure the product is suitable for the intended application. * These products also meet the requirements for PE 3408 per ASTM D3350-02a. @ Certified product may include a fused U-bend fitting.

Fabricated Ductile Iron Pipe
NAPF QualityPlus™ Certification Program

National Association of Pipe Fabricators
2313 Northeast 160th Loop
Vancouver, WA 98684
United States
205-706-0886
Visit this company's website

Facility : U.S. Pipe Fabrication Ephrata, PA

Product Type	Material Type	Trade Name	Product Standard
Pipe	Ductile Iron	U.S. Pipe	AWWA C115
Flanged Ductile Iron Pipe
3" - 64"
Pipe	Ductile Iron	U.S. Pipe	AWWA C606
Grooved / Shouldered Joint Pipe
3" - 64"

NOTE: Certification applies to grooved and/or flanged pipe only. Certification does not cover
      the design or rating of couplings or hydrostatic joint tests. Pipe may be flanged on one
      end and grooved on the other. In this case, pipe is Certified to both AWWA C115 and AWWA
      C606.
NOTE: Product is also Certified to NSF/ANSI/CAN 61 for drinking water applications.

Number of matching Manufacturers is 19
Number of matching Products is 901
Processing time was 1 seconds

NSF Product and Service Listings

Did you know?

Connect with NSF