NSF Product and Service Listings

[HP] Use of this product shall be followed by chlorination to remove levels of hydrogen
     peroxide.  Chlorine residuals shall not exceed 4 mg/L, the EPA's proposed maximum
     residual level.

[1] This product is designed to be used off-line and flushed out prior to using the system
    for drinking water, following manufacturer's use instructions.

[1] This product is designed to be used off-line and flushed out prior to using the system
    for drinking water, following manufacturer's use instructions.

[1] The finished drinking water should be monitored to ensure that levels of manganese do
    not exceed 0.05 mg/L.

[1] The finished drinking water should be monitored to ensure that levels of manganese do
    not exceed 0.05 mg/L

[1] The finished drinking water should be monitored to ensure that levels of manganese do
    not exceed 0.05 mg/L. 

[PO] The finished drinking water shall be monitored to ensure that levels of manganese

     do not exceed 0.05 mg/L.

[PO] The finished drinking water shall be monitored to ensure that levels of manganese

     do not exceed 0.05 mg/L.

[PO] The finished drinking water shall be monitored to ensure that levels of manganese

     do not exceed 0.05 mg/L.

[1] The finished drinking water should be monitored to ensure that levels of manganese do
    not exceed 0.05 mg/L.

[PO] The finished drinking water shall be monitored to ensure that levels of manganese

     do not exceed 0.05 mg/L.

[1] Certified for addition to the feedwater for evaporative desalination units only.
[2] This product contains sulfite. Sulfites have been known to cause potentially lethal
    allergic reactions in sulfite-sensitive individuals. The maximum recommended allowable
    residual sulfite level in the finished drinking water is 100 ppb (0.1 mg/L).

[CL] The residual levels of chlorine (hypochlorite ion and hypochlorous acid), chlorine
     dioxide, chlorate ion, chloramine and disinfection by-products shall be monitored in the
     finished drinking water to ensure compliance to all applicable regulations.

[CL] The residual levels of chlorine (hypochlorite ion and hypochlorous acid), chlorine
     dioxide, chlorate ion, chloramine and disinfection by-products shall be monitored in the
     finished drinking water to ensure compliance to all applicable regulations.

[1] End product is 40-42% Ferric Chloride.

[1] This product is designed to be used off-line and flushed out prior to using the system
    for drinking water, following the manufacturer's use instructions.
[2] The pH of the influent and effluent water should be monitored to ensure that all traces
    of the product have been removed before placing into service.

[1] This product is designed to be used off-line and flushed out prior to using the system
    for drinking water, following the manufacturer's use instructions.
[2] The pH of the influent and effluent water should be monitored to ensure that all traces
    of the product have been removed before placing into service.

[CL] The residual levels of chlorine (hypochlorite ion and hypochlorous acid), chlorine
     dioxide, chlorate ion, chloramine and disinfection by-products shall be monitored in the
     finished drinking water to ensure compliance to all applicable regulations.

[1] Microslay A and Microslay B are to be mixed following the manufacturer's use
    instructions to produce 0.6% chlorine dixoide solution.  Certification applies to the
    finished product.
[CL] The residual levels of chlorine (hypochlorite ion and hypochlorous acid), chlorine
     dioxide, chlorate ion, chloramine and disinfection by-products shall be monitored in the
     finished drinking water to ensure compliance to all applicable regulations.

[AL] Based on an evaluation of health effects data, the level of aluminum in the finished
     drinking water shall not exceed 2 mg/L.

[CL] The residual levels of chlorine (hypochlorite ion and hypochlorous acid), chlorine
     dioxide, chlorate ion, chloramine and disinfection by-products shall be monitored in the
     finished drinking water to ensure compliance to all applicable regulations.

[AL] Based on an evaluation of health effects data, the level of aluminum in the finished
     drinking water shall not exceed 2 mg/L.

[AL] Based on an evaluation of health effects data, the level of aluminum in the finished
     drinking water shall not exceed 2 mg/L.

[AL] Based on an evaluation of health effects data, the level of aluminum in the finished
     drinking water shall not exceed 2 mg/L.

[AL] Based on an evaluation of health effects data, the level of aluminum in the finished
     drinking water shall not exceed 2 mg/L.

[AL] Based on an evaluation of health effects data, the level of aluminum in the finished
     drinking water shall not exceed 2 mg/L.

[AL] Based on an evaluation of health effects data, the level of aluminum in the finished
     drinking water shall not exceed 2 mg/L.

[AL] Based on an evaluation of health effects data, the level of aluminum in the finished
     drinking water shall not exceed 2 mg/L.

[1] AA - 15 - 99.5
    BB - 0.5 - 25
    CC - 15 - 99.5
    DD - 26 - 55
    X  - 1 - 3
    Y  - 4 - 6
    ZZ - 20 - 99.5
    WW - 0.5 - 30
[AL] Based on an evaluation of health effects data, the level of aluminum in the finished
     drinking water shall not exceed 2 mg/L.

[AL] Based on an evaluation of health effects data, the level of aluminum in the finished
     drinking water shall not exceed 2 mg/L.

[1] AA - 15 - 99.5
    BB - 0.5 - 25
    CC - 15 - 99.5
    DD - 26 - 55
    X  - 1 - 3
    Y  - 4 - 6
    ZZ - 20 - 99.5
    WW - 0.5 - 30
[2] AA = 15 - 99.5
    BB = 0.5 - 25
    CC = 15 - 99.5
    DD = 26 - 55
    Y = 4 -6
    ZZ = 20 - 99.5
    WW = 0.5 - 30
    AA = % Concentration of GC 850 in the final bend
    BB = Polydadmac 40% concentration in the final blend
    CC = % Concentration of GC 850 in the final blend
    DD = Polydadmac 40% concentration in the final blend
    Y = 40% Polydadmac grade
    ZZ = % Concentration of GC 850 in the final blend
    WW = % Total polydadmac concentration in the final blend
[AL] Based on an evaluation of health effects data, the level of aluminum in the finished
     drinking water shall not exceed 2 mg/L.
[PY] Polyamines Certified by NSF International comply with 40 CFR 141.111 requirements for
     percent monomer and dose.

[AL] Based on an evaluation of health effects data, the level of aluminum in the finished
     drinking water shall not exceed 2 mg/L.

[AL] Based on an evaluation of health effects data, the level of aluminum in the finished
     drinking water shall not exceed 2 mg/L.

[CL] The residual levels of chlorine (hypochlorite ion and hypochlorous acid), chlorine
     dioxide, chlorate ion, chloramine and disinfection by-products shall be monitored in the
     finished drinking water to ensure compliance to all applicable regulations.

[1] This product contains sulfite.
   Sulfites have been known to cause potentially lethal
    allergic reactions in sulfite-sensitive individuals.
   The maximum recommended allowable
    residual sulfite level in the finished drinking water is 100 ppb (0.1 mg/L).

[2] This product is designed to be used off-line and flushed out prior to using the system
    for drinking water, following manufacturer's use instructions.

[CL] The residual levels of chlorine (hypochlorite ion and hypochlorous acid), chlorine
     dioxide, chlorate ion, chloramine and disinfection by-products shall be monitored in the
     finished drinking water to ensure compliance to all applicable regulations.

[1] The finished drinking water should be monitored to ensure that levels of manganese do
    not exceed 0.05 mg/L.

[PO] The finished drinking water shall be monitored to ensure that levels of manganese

     do not exceed 0.05 mg/L.

[CL] The residual levels of chlorine (hypochlorite ion and hypochlorous acid), chlorine
     dioxide, chlorate ion, chloramine and disinfection by-products shall be monitored in the
     finished drinking water to ensure compliance to all applicable regulations.

[1] AA = 15 - 99.5
    BB = 0.5 - 25
    CC = 15 - 99.5
    DD = 26 - 55
    Y = 4 -6
    ZZ = 20 - 99.5
    WW = 0.5 - 30
    AA = % Concentration of GC 850 in the final bend
    BB = Polydadmac 40% concentration in the final blend
    CC = % Concentration of GC 850 in the final blend
    DD = Polydadmac 40% concentration in the final blend
    Y = 40% Polydadmac grade
    ZZ = % Concentration of GC 850 in the final blend
    WW = % Total polydadmac concentration in the final blend
[AL] Based on an evaluation of health effects data, the level of aluminum in the finished
     drinking water shall not exceed 2 mg/L.

[AL] Based on an evaluation of health effects data, the level of aluminum in the finished
     drinking water shall not exceed 2 mg/L.

[CL] The residual levels of chlorine (hypochlorite ion and hypochlorous acid), chlorine
     dioxide, chlorate ion, chloramine and disinfection by-products shall be monitored in the
     finished drinking water to ensure compliance to all applicable regulations.

[3] Certified for use as an off-line membrane cleaner.  When used as an off-line membrane
    cleaner, this product is designed to be flushed out prior to using the system for
    drinking water.  Follow manufacturer's use instructions.

[1] These products are designed to be used off-line and flushed out prior to using the
    system for drinking water, following manufacturer's use instructions.
[2] The pH of the influent and effluent water shall be monitored to ensure that all traces
    of the product have been removed before placing into service.

[1] These products are designed to be used off-line and flushed out prior to using the
    system for drinking water, following manufacturer's use instructions.

[1] These products are designed to be used off-line and flushed out prior to using the
    system for drinking water, following manufacturer's use instructions.
[2] The pH of the influent and effluent water shall be monitored to ensure that all traces
    of the product have been removed before placing into service.

[3] Certified for use as an off-line membrane cleaner.  When used as an off-line membrane
    cleaner, this product is designed to be flushed out prior to using the system for
    drinking water.  Follow manufacturer's use instructions.

[1] These products are designed to be used off-line and flushed out prior to using the
    system for drinking water, following manufacturer's use instructions.
[2] The pH of the influent and effluent water shall be monitored to ensure that all traces
    of the product have been removed before placing into service.

[1] These products are designed to be used off-line and flushed out prior to using the
    system for drinking water, following manufacturer's use instructions.

[1] These products are designed to be used off-line and flushed out prior to using the
    system for drinking water, following manufacturer's use instructions.
[2] The pH of the influent and effluent water shall be monitored to ensure that all traces
    of the product have been removed before placing into service.

[PC] Polyacrylamide Products Certified by NSF International comply with 40 CFR 141.111
     requirements for percent monomer and dose.

[AL] Based on an evaluation of health effects data, the level of aluminum in the finished
     drinking water shall not exceed 2 mg/L.

[PY] Polyamines Certified by NSF International comply with 40 CFR 141.111 requirements for
     percent monomer and dose.

[AL] Based on an evaluation of health effects data, the level of aluminum in the finished
     drinking water shall not exceed 2 mg/L.
[PY] Polyamines Certified by NSF International comply with 40 CFR 141.111 requirements for
     percent monomer and dose.

[AL] Based on an evaluation of health effects data, the level of aluminum in the finished
     drinking water shall not exceed 2 mg/L.

[CL] The residual levels of chlorine (hypochlorite ion and hypochlorous acid), chlorine
     dioxide, chlorate ion, chloramine and disinfection by-products shall be monitored in the
     finished drinking water to ensure compliance to all applicable regulations.

[1] This product is designed to be used off-line and flushed out prior to using the system
    for drinking water, following the manufacturer's use instructions.
[2] This pH of the influent and effluent water should be monitored to ensure that all traces
    of the product have been removed before placing into service.

[PC] Polyacrylamide Products Certified by NSF International comply with 40 CFR 141.111
     requirements for percent monomer and dose.

[AL] Based on an evaluation of health effects data, the level of aluminum in the finished
     drinking water shall not exceed 2 mg/L.

[AL] Based on an evaluation of health effects data, the level of aluminum in the finished
     drinking water shall not exceed 2 mg/L.
[PY] Polyamines Certified by NSF International comply with 40 CFR 141.111 requirements for
     percent monomer and dose.

[CL] The residual levels of chlorine (hypochlorite ion and hypochlorous acid), chlorine
     dioxide, chlorate ion, chloramine and disinfection by-products shall be monitored in the
     finished drinking water to ensure compliance to all applicable regulations.

[CL] The residual levels of chlorine (hypochlorite ion and hypochlorous acid), chlorine
     dioxide, chlorate ion, chloramine and disinfection by-products shall be monitored in the
     finished drinking water to ensure compliance to all applicable regulations.

[PO] The finished drinking water shall be monitored to ensure that levels of manganese

     do not exceed 0.05 mg/L.

[PO] The finished drinking water shall be monitored to ensure that levels of manganese

     do not exceed 0.05 mg/L.

[PY] Polyamines Certified by NSF International comply with 40 CFR 141.111 requirements for
     percent monomer and dose.

[AL] Based on an evaluation of health effects data, the level of aluminum in the finished
     drinking water shall not exceed 2 mg/L.

[1] When this product is used offline, it is designed to be flushed out prior to using the
    system for drinking water, following manufacturer's use instructions.
    
[2] This product is certified to NSF/ANSI/CAN 60, but it has not been registered under the
    US FIFRA requirements and is not to be distributed within the USA.
    
[3] This product is designed to be used off-line and flushed out prior to using the system
    for drinking water, following manufacturer's use instructions.

[1] This product is designed to be used off-line and flushed out prior to using the system
    for drinking water, following manufacturer's use instructions.

[PY] Polyamines Certified by NSF International comply with 40 CFR 141.111 requirements for
     percent monomer and dose.

[HP] Use of this product shall be followed by chlorination to remove levels of hydrogen
     peroxide.  Chlorine residuals shall not exceed 4 mg/L, the EPA's proposed maximum
     residual level.

[1] When this product is used offline, it is designed to be flushed out prior to using the
    system for drinking water, following manufacturer's use instructions.
[2] This product is certified to NSF/ANSI/CAN 60, but it has not been registered under the
    US FIFRA requirements and is not to be distributed within the USA.
[3] This product is designed to be used off-line and flushed out prior to using the system
    for drinking water, following manufacturer's use instructions.

[PY] Polyamines Certified by NSF International comply with 40 CFR 141.111 requirements for
     percent monomer and dose.

[CL] The residual levels of chlorine (hypochlorite ion and hypochlorous acid), chlorine
     dioxide, chlorate ion, chloramine and disinfection by-products shall be monitored in the
     finished drinking water to ensure compliance to all applicable regulations.

[CL] The residual levels of chlorine (hypochlorite ion and hypochlorous acid), chlorine
     dioxide, chlorate ion, chloramine and disinfection by-products shall be monitored in the
     finished drinking water to ensure compliance to all applicable regulations.

[PC] Polyacrylamide Products Certified by NSF International comply with 40 CFR 141.111
     requirements for percent monomer and dose.

[AL] Based on an evaluation of health effects data, the level of aluminum in the finished
     drinking water shall not exceed 2 mg/L.

[1] This product is designed to be used off-line and flushed out prior to using the system
    for drinking water, following manufacturer's use instructions.

[1] This product is designed to be used off-line and flushed out prior to using the system
    for drinking water, following manufacturer's use instructions.
[2] The pH of the influent and effluent water should be monitored to ensure that all traces
    of the product have been removed before placing into service.

[3] Certified for addition to the feedwater for evaporative desalination units only.

[4] This product contains sulfite. Sulfites have been known to cause potentially lethal
    allergic reactions in sulfite-sensitive individuals. The maximum recommended allowable
    residual sulfite level in the finished drinking water is 100 ppb (0.1 mg/L).

[CL] The residual levels of chlorine (hypochlorite ion and hypochlorous acid), chlorine
     dioxide, chlorate ion, chloramine and disinfection by-products shall be monitored in the
     finished drinking water to ensure compliance to all applicable regulations.

[PO] The finished drinking water shall be monitored to ensure that levels of manganese

     do not exceed 0.05 mg/L.

[PO] The finished drinking water shall be monitored to ensure that levels of manganese

     do not exceed 0.05 mg/L.

[CL] The residual levels of chlorine (hypochlorite ion and hypochlorous acid), chlorine
     dioxide, chlorate ion, chloramine and disinfection by-products shall be monitored in the
     finished drinking water to ensure compliance to all applicable regulations.

[1] The finished drinking water should be monitored to ensure that levels of manganese do
    not exceed 0.05 mg/L.
[2] Based on an evaluation of health effects data, the level of aluminum in the finished
    drinking water should not exceed 2 mg/L.
[PO] The finished drinking water shall be monitored to ensure that levels of manganese

     do not exceed 0.05 mg/L.

[1] Component A and Component B are to be mixed following manufacturer's use instructions to
    produce a 1% chlorine dioxide solution. Certification and maximum use level applies to
    the finished product.
[CL] The residual levels of chlorine (hypochlorite ion and hypochlorous acid), chlorine
     dioxide, chlorate ion, chloramine and disinfection by-products shall be monitored in the
     finished drinking water to ensure compliance to all applicable regulations.

[HP] Use of this product shall be followed by chlorination to remove levels of hydrogen
     peroxide.  Chlorine residuals shall not exceed 4 mg/L, the EPA's proposed maximum
     residual level.

[1] This product is to be added to the feedwater of evaporator type units only.

[PC] Polyacrylamide Products Certified by NSF International comply with 40 CFR 141.111
     requirements for percent monomer and dose.

[PO] The finished drinking water shall be monitored to ensure that levels of manganese

     do not exceed 0.05 mg/L.

[CL] The residual levels of chlorine (hypochlorite ion and hypochlorous acid), chlorine
     dioxide, chlorate ion, chloramine and disinfection by-products shall be monitored in the
     finished drinking water to ensure compliance to all applicable regulations.

[5] For products distributed in Canada, the company name on the product label may be shown
    as Veolia Water Technologies & Solutions Canada GP, Oakville, ON.
[AL] Based on an evaluation of health effects data, the level of aluminum in the finished
     drinking water shall not exceed 2 mg/L.

[1] This product is designed to be used off-line and flushed out prior to using the system
    for drinking water, following manufacturer's use instructions.
[2] The pH of the influent and effluent water should be monitored to ensure that all traces
    of the product have been removed before placing into service.
[5] For products distributed in Canada, the company name on the product label may be shown
    as Veolia Water Technologies & Solutions Canada GP, Oakville, ON.

[5] For products distributed in Canada, the company name on the product label may be shown
    as Veolia Water Technologies & Solutions Canada GP, Oakville, ON.