NSF Product and Service Listings

[1] This product is designed to be flushed out prior to using the system for drinking water.
     The well is to be properly flushed and drained before being placed into service.  This
    product is to be used according to the manufacturer's use instructions.
[2] These products are designed to be flushed out prior to using the system for drinking
    water. Before being placed into service, the well is to be properly flushed according to
    the manufacturer's use instructions. Certification of these products is based on the
    well drilling model with the following assumptions: 
    - The amount of well drilling fluid used is 3780 L (1000 U.S. gallons) to which
      the drilling fluid has been added at the manufacturer's recommended level.
    - The aquifer contains 3.1 million liters of water (815,000 gallons) based on a 0.5 acre
      aquifer of 6.1 meter depth (20 ft.) and 25% porosity.
    - The bore hole is 61 meters in total depth (200 ft.), the screen is 6.1 meters in
    length
      (20 ft.), and the bore hole is 25.4 cm. in diameter (10 in.).
    - The amount of well drilling fluid removed from the well during construction is equal
    to 
      the combined volumes of the casing and the screen, plus an additional amount removed 
      through the well disinfection and development (90% removed).
    - This product should not be used in constructing wells in highly porous formations,
    such
      as cavernous limestone.

[1] This product is designed to be flushed out prior to using the system for drinking water.
     The well is to be properly flushed and drained before being placed into service.  This
    product is to be used according to the manufacturer's use instructions.
[2] These products are designed to be flushed out prior to using the system for drinking
    water. Before being placed into service, the well is to be properly flushed according to
    the manufacturer's use instructions. Certification of these products is based on the
    well drilling model with the following assumptions: 
    - The amount of well drilling fluid used is 3780 L (1000 U.S. gallons) to which
      the drilling fluid has been added at the manufacturer's recommended level.
    - The aquifer contains 3.1 million liters of water (815,000 gallons) based on a 0.5 acre
      aquifer of 6.1 meter depth (20 ft.) and 25% porosity.
    - The bore hole is 61 meters in total depth (200 ft.), the screen is 6.1 meters in
    length
      (20 ft.), and the bore hole is 25.4 cm. in diameter (10 in.).
    - The amount of well drilling fluid removed from the well during construction is equal
    to 
      the combined volumes of the casing and the screen, plus an additional amount removed 
      through the well disinfection and development (90% removed).
    - This product should not be used in constructing wells in highly porous formations,
    such
      as cavernous limestone.
[PC] Polyacrylamide Products Certified by NSF International comply with 40 CFR 141.111
     requirements for percent monomer and dose.
[PY] Polyamines Certified by NSF International comply with 40 CFR 141.111 requirements for
     percent monomer and dose.

[PY] Polyamines Certified by NSF International comply with 40 CFR 141.111 requirements for
     percent monomer and dose.

[PY] Polyamines Certified by NSF International comply with 40 CFR 141.111 requirements for
     percent monomer and dose.

[PY] Polyamines Certified by NSF International comply with 40 CFR 141.111 requirements for
     percent monomer and dose.

[AL] Based on an evaluation of health effects data, the level of aluminum in the finished
     drinking water shall not exceed 2 mg/L.
[PY] Polyamines Certified by NSF International comply with 40 CFR 141.111 requirements for
     percent monomer and dose.