NSF Product and Service Listings
These NSF Official Listings are current as of Thursday, January 15, 2026 at 12:15 a.m. Eastern Time. Please contact NSF to confirm the status of any Listing, report errors, or make suggestions.
Alert: NSF is concerned about fraudulent downloading and manipulation of website text. Always confirm this information by clicking on the below link for the most accurate information: http://info.nsf.org/Certified/PwsChemicals/Listings.asp?Company=49810&Standard=060&
NSF/ANSI/CAN 60
Drinking Water Treatment Chemicals - Health Effects
Drinking Water Treatment Chemicals - Health Effects
| Water Solutions Unlimited, Inc. | |
| 8824 Union Mills Drive | |
| Camby, IN 46113 | |
| United States | |
| 800-359-3570 | |
| 317-736-6868 |
Facility : East Peoria, IL
|
Ammonium Sulfate |
||
| Trade Designation | Product Function | Max Use |
| Ammonium Sulfate 40% | Disinfection & Oxidation | 60mg/L |
| WSU 40% Ammonium Sulfate | Disinfection & Oxidation | 60mg/L |
| WSU 40% Liquid Ammonium Sulfate | Disinfection & Oxidation | 60mg/L |
| WSU Ammonium Sulfate 40% | Disinfection & Oxidation | 60mg/L |
|
Blended Phosphates[1] |
||
| Trade Designation | Product Function | Max Use |
| WSU 110 | Corrosion & Scale Control Sequestering |
21mg/L |
| WSU 118 | Corrosion & Scale Control Sequestering |
21mg/L |
| WSU 120 | Corrosion & Scale Control Sequestering |
26mg/L |
| WSU 140 | Corrosion & Scale Control Sequestering |
26mg/L |
| WSU 150 | Corrosion & Scale Control Sequestering |
25mg/L |
| WSU 158 | Corrosion & Scale Control Sequestering |
16mg/L |
| WSU 178 | Corrosion & Scale Control Sequestering |
17mg/L |
| WSU 189 | Corrosion & Scale Control Sequestering |
21mg/L |
[1] Only products bearing the NSF Mark on the product, product packaging, and/or
documentation shipped with the product are Certified.
|
||
|
Copper Sulfate[1] [2] |
||
| Trade Designation | Product Function | Max Use |
| MAIN STREAM 635 | Algicide Bactericide |
19mg/L |
[1] Only products bearing the NSF Mark on the product, product packaging, and/or
documentation shipped with the product are Certified.
[2] The use of copper sulfate as an algicide may increase the amount of copper present in
the finished drinking water. Following use of this product, the finished drinking water
should be monitored to ensure that levels of copper do not exceed regulatory
requirements.
|
||
|
Fluorosilicic Acid[1] |
||
| Trade Designation | Product Function | Max Use |
| Fluorosilicic Acid 23% | Fluoridation | 5mg/L |
| WSU 23% Fluorosilicic Acid | Fluoridation | 5mg/L |
| WSU Fluorosilicic Acid 23% | Fluoridation | 5mg/L |
[1] Only products bearing the NSF Mark on the product, product packaging, and/or
documentation shipped with the product are Certified.
|
||
|
Miscellaneous Chemical Products[1] [PO] |
||
| Trade Designation | Product Function | Max Use |
| WSU HMO 3% Solution[4] | Other | 3mg/L |
[1] Only products bearing the NSF Mark on the product, product packaging, and/or
documentation shipped with the product are Certified.
[4] This product has been Certified for use upstream of sand filtration. It is intended to
be removed during periodic backflushing of the sand filter.
[PO] The finished drinking water shall be monitored to ensure that levels of manganese
do not exceed 0.05 mg/L.
|
||
|
Miscellaneous Treatment Chemical[1] [CL] |
||
| Trade Designation | Product Function | Max Use |
| WSU ORA-CLE | Disinfection & Oxidation Scale Control |
2945mg/L |
[1] Only products bearing the NSF Mark on the product, product packaging, and/or
documentation shipped with the product are Certified.
[CL] The residual levels of chlorine (hypochlorite ion and hypochlorous acid), chlorine
dioxide, chlorate ion, chloramine and disinfection by-products shall be monitored in the
finished drinking water to ensure compliance to all applicable regulations.
|
||
|
Sodium Hydroxide |
||
| Trade Designation | Product Function | Max Use |
| WSU Sodium Hydroxide 25% | Corrosion & Scale Control | 200mg/L |
|
Sodium Hypochlorite[1] [HY] |
||
| Trade Designation | Product Function | Max Use |
| WSU HYPOCHLORITE 125 | Disinfection & Oxidation | 65mg/L |
| WSU HYPOCHLORITE 125M | Disinfection & Oxidation | 65mg/L |
[1] Only products bearing the NSF Mark on the product, product packaging, and/or
documentation shipped with the product are Certified.
[HY] The residual levels of chlorine (hypochlorite ion and hypochlorous acid), chlorine
dioxide, chlorate ion, chloramine and disinfection by-products shall be monitored in the
finished drinking water to ensure compliance to all applicable regulations. Also,
reference the AWWA B300 (Hypochlorites) standard's Recommendations for the Handling and
Storage of Hypochlorite Solutions appendix for information on preservation techniques
for hypochlorite bleach in transit and storage.
|
||
|
Sodium Permanganate[5] |
||
| Trade Designation | Product Function | Max Use |
| Sodium Permanganate 1% | Disinfection & Oxidation | 3250mg/L |
| Sodium Permanganate 20% | Disinfection & Oxidation | 176mg/L |
| WSU 1% Sodium Permanganate | Disinfection & Oxidation | 3250mg/L |
| WSU 20% Sodium Permanganate | Disinfection & Oxidation | 176mg/L |
| WSU Sodium Permanganate 1% | Disinfection & Oxidation | 3250mg/L |
| WSU Sodium Permanganate 20% | Disinfection & Oxidation | 176mg/L |
[5] The finished drinking water should be monitored to ensure that levels of manganese do
not exceed 0.05 mg/L.
|
||
|
Sodium Polyphosphates, Glassy[1] |
||
| Trade Designation | Product Function | Max Use |
| WSU 101 | Corrosion Control | 29mg/L |
[1] Only products bearing the NSF Mark on the product, product packaging, and/or
documentation shipped with the product are Certified.
|
||
|
Zinc Orthophosphate[ZN] |
||
| Trade Designation | Product Function | Max Use |
| WSU 403 | Corrosion & Scale Control | 16mg/L |
| WSU 405 | Corrosion & Scale Control | 15mg/L |
[ZN] Based on an evaluation of health effects data, the level of zinc in the finished
drinking water shall not exceed 2.0 mg/L.
|
||
Facility : Camby, IN
|
Aluminum Chloride[AL] |
||
| Trade Designation | Product Function | Max Use |
| Aqua Hawk® 1010 | Coagulation & Flocculation | 250mg/L |
[AL] Based on an evaluation of health effects data, the level of aluminum in the finished
drinking water shall not exceed 2 mg/L.
|
||
|
Aluminum Chlorohydrate[1] [AL] |
||
| Trade Designation | Product Function | Max Use |
| WSU FLOC 4000 | Coagulation & Flocculation | 250mg/L |
[1] Only products bearing the NSF Mark on the product, product packaging, and/or
documentation shipped with the product are Certified.
[AL] Based on an evaluation of health effects data, the level of aluminum in the finished
drinking water shall not exceed 2 mg/L.
|
||
|
Aluminum Sulfate[1] [AL] |
||
| Trade Designation | Product Function | Max Use |
| WSU Aluminum Sulfate 48% | Coagulation & Flocculation | 400mg/L |
[1] Only products bearing the NSF Mark on the product, product packaging, and/or
documentation shipped with the product are Certified.
[AL] Based on an evaluation of health effects data, the level of aluminum in the finished
drinking water shall not exceed 2 mg/L.
|
||
|
Ammonium Sulfate[1] |
||
| Trade Designation | Product Function | Max Use |
| Ammonium Sulfate 40% | Disinfection & Oxidation | 60mg/L |
| WSU 40% Ammonium Sulfate | Disinfection & Oxidation | 60mg/L |
| WSU 40% Liquid Ammonium Sulfate | Disinfection & Oxidation | 60mg/L |
| WSU Ammonium Sulfate 40% | Disinfection & Oxidation | 60mg/L |
| WSU Ammonium Sulfate-Dry | Disinfection & Oxidation | 25mg/L |
[1] Only products bearing the NSF Mark on the product, product packaging, and/or
documentation shipped with the product are Certified.
|
||
|
Blended Phosphates[1] |
||
| Trade Designation | Product Function | Max Use |
| AquaFix 160 | Corrosion & Scale Control Sequestering |
24mg/L |
| AquaFix 190 | Corrosion & Scale Control Sequestering |
28mg/L |
| AquaFresh 125 | Sequestering Corrosion & Scale Control |
17mg/L |
| AquaFresh 150 | Sequestering Corrosion & Scale Control |
16mg/L |
| AquaFresh 160 | Corrosion & Scale Control Sequestering |
24mg/L |
| AquaFresh 170 | Corrosion & Scale Control Sequestering |
28mg/L |
| AquaFresh 190 | Corrosion & Scale Control Sequestering |
28mg/L |
| AquaGold 125 | Sequestering Corrosion & Scale Control |
17mg/L |
| AquaGold 150 | Sequestering Corrosion & Scale Control |
16mg/L |
| AquaGold 160 | Corrosion & Scale Control Sequestering |
24mg/L |
| AquaGold 170 | Corrosion & Scale Control Sequestering |
28mg/L |
| AquaGold 190 | Corrosion & Scale Control Sequestering |
28mg/L |
| AquaSharp 160 | Corrosion & Scale Control Sequestering |
24mg/L |
| AquaSharp 190 | Corrosion & Scale Control Sequestering |
28mg/L |
| Aquagold 121 | Corrosion & Scale Control Sequestering |
46mg/L |
| EMD 00 VL 18 | Corrosion & Scale Control Sequestering |
46mg/L |
| EMD 00 ZG 85 | Corrosion & Scale Control Sequestering |
12mg/L |
| EMD 30 YXL 33 | Corrosion & Scale Control Sequestering |
28mg/L |
| EMD 40 YXL 31 | Corrosion & Scale Control Sequestering |
24mg/L |
| EMD 50 XZG 80 | Corrosion & Scale Control Sequestering |
12mg/L |
| EMD 50 YXL 35 | Corrosion & Scale Control Sequestering |
16mg/L |
| EMD 70 YXL 33 | Corrosion & Scale Control Sequestering |
17mg/L |
| EMD 85 XG 80 | Corrosion & Scale Control Sequestering |
12mg/L |
| EMD 90 XG 79 | Corrosion & Scale Control Sequestering |
12mg/L |
| EMD 90 YXL 33 | Corrosion & Scale Control Sequestering |
21mg/L |
| RG-100 Plus | Corrosion & Scale Control Sequestering |
28mg/L |
| WSU 110 | Corrosion & Scale Control Sequestering |
21mg/L |
| WSU 118 | Corrosion & Scale Control Sequestering |
21mg/L |
| WSU 120 | Corrosion & Scale Control Sequestering |
26mg/L |
| WSU 121 | Corrosion & Scale Control Sequestering |
46mg/L |
| WSU 137 | Sequestering Corrosion & Scale Control |
19mg/L |
| WSU 140 | Corrosion & Scale Control Sequestering |
26mg/L |
| WSU 150 | Corrosion & Scale Control Sequestering |
25mg/L |
| WSU 158 | Corrosion & Scale Control Sequestering |
16mg/L |
| WSU 160 | Corrosion & Scale Control Sequestering |
24mg/L |
| WSU 178 | Corrosion & Scale Control Sequestering |
17mg/L |
| WSU 189 | Corrosion & Scale Control Sequestering |
21mg/L |
| WSU 190 | Corrosion & Scale Control Sequestering |
28mg/L |
| WSU 310 | Corrosion & Scale Control Sequestering |
12mg/L |
| WSU 318 | Corrosion & Scale Control Sequestering |
12mg/L |
| WSU 319 | Corrosion & Scale Control Sequestering |
12mg/L |
| WSU 350 | Corrosion & Scale Control Sequestering |
12mg/L |
| WSU 358 | Corrosion & Scale Control Sequestering |
12mg/L |
| WSU 378 | Corrosion & Scale Control Sequestering |
12mg/L |
| WSU 385 | Corrosion & Scale Control Sequestering |
12mg/L |
| WSU 389 | Corrosion & Scale Control Sequestering |
12mg/L |
| WSU HC 300 | Corrosion & Scale Control Sequestering |
75mg/L |
| WSU HYPO-CLEAN | Corrosion & Scale Control Sequestering |
29mg/L |
[1] Only products bearing the NSF Mark on the product, product packaging, and/or
documentation shipped with the product are Certified.
|
||
|
Citric Acid[1] |
||
| Trade Designation | Product Function | Max Use |
| Citric Acid 50%[2] | Membrane Cleaner | NA |
| WSU 50% Citric Acid[2] | Membrane Cleaner | NA |
[1] Only products bearing the NSF Mark on the product, product packaging, and/or
documentation shipped with the product are Certified.
[2] This product is designed to be used off-line and flushed out prior to using the system
for drinking water, following manufacturer's use instructions.
|
||
|
Copper Sulfate[1] [CP] |
||
| Trade Designation | Product Function | Max Use |
| MAIN STREAM 635[3] | Algicide Bactericide |
19mg/L |
[1] Only products bearing the NSF Mark on the product, product packaging, and/or
documentation shipped with the product are Certified.
[3] The use of copper sulfate as an algicide may increase the amount of copper present in
the finished drinking water. Following use of this product, the finished drinking water
should be monitored to ensure that levels of copper do not exceed regulatory
requirements.
[CP] The finished drinking water shall be monitored to ensure that levels of copper do not
exceed 1.3 mg/L.
|
||
|
Ferric Chloride |
||
| Trade Designation | Product Function | Max Use |
| Ferric Chloride 38% | Coagulation & Flocculation | 250mg/L |
| WSU 38% Ferric Chloride | Coagulation & Flocculation | 250mg/L |
| WSU Ferric Chloride 38% | Coagulation & Flocculation | 250mg/L |
|
Ferric Sulfate[1] |
||
| Trade Designation | Product Function | Max Use |
| WSU Ferric Sulfate 50% | Coagulation & Flocculation | 600mg/L |
| WSU Ferric Sulfate 60% | Coagulation & Flocculation | 600mg/L |
[1] Only products bearing the NSF Mark on the product, product packaging, and/or
documentation shipped with the product are Certified.
|
||
|
Fluorosilicic Acid[1] |
||
| Trade Designation | Product Function | Max Use |
| Fluorosilicic Acid 23% | Fluoridation | 5mg/L |
| WSU 23% Fluorosilicic Acid | Fluoridation | 5mg/L |
| WSU Fluorosilicic Acid 23% | Fluoridation | 5mg/L |
[1] Only products bearing the NSF Mark on the product, product packaging, and/or
documentation shipped with the product are Certified.
|
||
|
Hydrogen Peroxide[1] [HP] |
||
| Trade Designation | Product Function | Max Use |
| WSU Hydrogen Peroxide 32-34% | Oxidant Disinfection & Oxidation |
3mg/L |
[1] Only products bearing the NSF Mark on the product, product packaging, and/or
documentation shipped with the product are Certified.
[HP] Use of this product shall be followed by chlorination to remove levels of hydrogen
peroxide. Chlorine residuals shall not exceed 4 mg/L, the EPA's proposed maximum
residual level.
|
||
|
Miscellaneous Treatment Chemical[1] |
||
| Trade Designation | Product Function | Max Use |
| Sodium Thiosulfate 30% | Dechlorination | 50mg/L |
| WSU 30% Sodium Thiosulfate | Dechlorination | 50mg/L |
| WSU CA 500[2] [5] [6] [7] | Other | NA |
| WSU CA500[2] [5] [7] [13] | Other | NA |
| WSU FW 833[2] [5] [8] | Other | NA |
| WSU NE 222[2] [5] [9] | Other | NA |
| WSU NE 422[2] [5] [9] | Other | NA |
| WSU ORA-CLE[HY] | Disinfection & Oxidation Scale Control |
2945mg/L |
| WSU Sodium Thiosulfate 30% | Dechlorination | 50mg/L |
| WSU TC 622[2] [5] [10] | Other | NA |
[1] Only products bearing the NSF Mark on the product, product packaging, and/or
documentation shipped with the product are Certified.
[2] This product is designed to be used off-line and flushed out prior to using the system
for drinking water, following manufacturer's use instructions.
[5] The pH of the influent and effluent water should be monitored to ensure that all traces
of the product have been removed before placing into service.
[6] This product functions as a cleaner for interior filter walls and may be used in
conjunction with WSU CA-500 Catalyst.
[7] This product is to be used in conjunction with WSU MC 444, MC 477, or WSU FW 833.
[8] This product functions as a cleaner for interior filter walls.
[9] This product functions as a neutralizer for off-line filter cleaners.
[10] This product functions as a cleaner for interior water tower and ground storage tank
walls.
[13] This product functions as a in situ filter media cleaner.
[HY] The residual levels of chlorine (hypochlorite ion and hypochlorous acid), chlorine
dioxide, chlorate ion, chloramine and disinfection by-products shall be monitored in the
finished drinking water to ensure compliance to all applicable regulations. Also,
reference the AWWA B300 (Hypochlorites) standard's Recommendations for the Handling and
Storage of Hypochlorite Solutions appendix for information on preservation techniques
for hypochlorite bleach in transit and storage.
|
||
|
Miscellaneous Water Supply Products[1] |
||
| Trade Designation | Product Function | Max Use |
| WSU MC 444[2] [5] [6] [11] | Other | NA |
| WSU MC 477[2] [5] [6] [11] | Other | NA |
[1] Only products bearing the NSF Mark on the product, product packaging, and/or
documentation shipped with the product are Certified.
[2] This product is designed to be used off-line and flushed out prior to using the system
for drinking water, following manufacturer's use instructions.
[5] The pH of the influent and effluent water should be monitored to ensure that all traces
of the product have been removed before placing into service.
[6] This product functions as a cleaner for interior filter walls and may be used in
conjunction with WSU CA-500 Catalyst.
[11] This product is to be used in conjunction with WSU CA-500 Catalyst.
|
||
|
Monosodium Orthophosphate[1] |
||
| Trade Designation | Product Function | Max Use |
| EMD 100 ML 28 | Corrosion Control | 26mg/L |
| WSU 111 | Corrosion Control Sequestering |
26mg/L |
| WSU 111 B | Corrosion Control Sequestering |
26mg/L |
[1] Only products bearing the NSF Mark on the product, product packaging, and/or
documentation shipped with the product are Certified.
|
||
|
Phosphoric Acid[1] |
||
| Trade Designation | Product Function | Max Use |
| Phosphoric Acid 75% | Corrosion & Scale Control pH Adjustment |
12mg/L |
| WSU 108 | Corrosion & Scale Control pH Adjustment |
12mg/L |
| WSU 109 | Corrosion & Scale Control Scale Control |
13mg/L |
| WSU 75% Phosphoric Acid | Corrosion & Scale Control pH Adjustment |
12mg/L |
| WSU Phosphoric Acid 75% | Corrosion & Scale Control pH Adjustment |
12mg/L |
[1] Only products bearing the NSF Mark on the product, product packaging, and/or
documentation shipped with the product are Certified.
|
||
|
Polyaluminum Chloride[AL] |
||
| Trade Designation | Product Function | Max Use |
| WSU Floc 6044 | Coagulation & Flocculation | 250mg/L |
[AL] Based on an evaluation of health effects data, the level of aluminum in the finished
drinking water shall not exceed 2 mg/L.
|
||
|
Potassium Hydroxide |
||
| Trade Designation | Product Function | Max Use |
| Potassium Hydroxide 45% | Corrosion & Scale Control pH Adjustment |
100mg/L |
| WSU 45% Potassium Hydroxide | Corrosion & Scale Control pH Adjustment |
100mg/L |
| WSU Potassium Hydroxide 45% | Corrosion & Scale Control pH Adjustment |
100mg/L |
|
Sodium Bisulfite[1] [12] |
||
| Trade Designation | Product Function | Max Use |
| Sodium Bisulfite 40% | Dechlorinator & Antioxidant | 46mg/L |
| WSU 40% Sodium Bisulfite | Dechlorinator & Antioxidant | 46mg/L |
| WSU Sodium Bisulfite 40% | Dechlorinator & Antioxidant | 46mg/L |
[1] Only products bearing the NSF Mark on the product, product packaging, and/or
documentation shipped with the product are Certified.
[12] This product contains sulfite. Sulfites have been known to cause potentially lethal
allergic reactions in sulfite-sensitive individuals. The maximum recommended allowable
residual sulfite level in the finished drinking water is 100 ppb (0.1 mg/L).
|
||
|
Sodium Carbonate[1] |
||
| Trade Designation | Product Function | Max Use |
| Sodium Carbonate 15% | Corrosion & Scale Control pH Adjustment |
667mg/L |
| WSU 15% Sodium Carbonate | Corrosion & Scale Control pH Adjustment |
667mg/L |
| WSU Sodium Carbonate 15% | Corrosion & Scale Control pH Adjustment |
667mg/L |
[1] Only products bearing the NSF Mark on the product, product packaging, and/or
documentation shipped with the product are Certified.
|
||
|
Sodium Hydroxide[1] |
||
| Trade Designation | Product Function | Max Use |
| Sodium Hydroxide 20% | Corrosion & Scale Control pH Adjustment |
250mg/L |
| WSU Sodium Hydroxide 20% | Corrosion & Scale Control pH Adjustment |
250mg/L |
| WSU Sodium Hydroxide 25% | Corrosion & Scale Control pH Adjustment |
200mg/L |
| WSU Sodium Hydroxide 30% | Corrosion & Scale Control pH Adjustment |
166mg/L |
| WSU Sodium Hydroxide 40% | Corrosion & Scale Control pH Adjustment |
125mg/L |
| WSU Sodium Hydroxide 50% | Corrosion & Scale Control pH Adjustment |
100mg/L |
[1] Only products bearing the NSF Mark on the product, product packaging, and/or
documentation shipped with the product are Certified.
|
||
|
Sodium Hypochlorite[HY] |
||
| Trade Designation | Product Function | Max Use |
| WSU HYPOCHLORITE 125 | Disinfection & Oxidation | 65mg/L |
| WSU HYPOCHLORITE 125M | Disinfection & Oxidation | 65mg/L |
[HY] The residual levels of chlorine (hypochlorite ion and hypochlorous acid), chlorine
dioxide, chlorate ion, chloramine and disinfection by-products shall be monitored in the
finished drinking water to ensure compliance to all applicable regulations. Also,
reference the AWWA B300 (Hypochlorites) standard's Recommendations for the Handling and
Storage of Hypochlorite Solutions appendix for information on preservation techniques
for hypochlorite bleach in transit and storage.
|
||
|
Sodium Permanganate[1] [PO] |
||
| Trade Designation | Product Function | Max Use |
| Sodium Permanganate 1% | Disinfection & Oxidation | 3250mg/L |
| Sodium Permanganate 20% | Disinfection & Oxidation | 176mg/L |
| Sodium Permanganate 40% | Disinfection & Oxidation | 88mg/L |
| WSU 1% Sodium Permanganate | Oxidant | 3250mg/L |
| WSU 20% Sodium Permanganate | Oxidant | 176mg/L |
| WSU 40% Sodium Permanganate | Disinfection & Oxidation | 88mg/L |
| WSU Sodium Permanganate 1% | Disinfection & Oxidation | 3250mg/L |
| WSU Sodium Permanganate 20% | Disinfection & Oxidation | 176mg/L |
| WSU Sodium Permanganate 40% | Disinfection & Oxidation | 88mg/L |
[1] Only products bearing the NSF Mark on the product, product packaging, and/or
documentation shipped with the product are Certified.
[PO] The finished drinking water shall be monitored to ensure that levels of manganese
do not exceed 0.05 mg/L.
|
||
|
Sodium Polyphosphates, Glassy[1] |
||
| Trade Designation | Product Function | Max Use |
| EMD 00 YL 36 | Corrosion & Scale Control Sequestering |
29mg/L |
| WSU 101 | Corrosion & Scale Control | 29mg/L |
[1] Only products bearing the NSF Mark on the product, product packaging, and/or
documentation shipped with the product are Certified.
|
||
|
Sulfuric Acid |
||
| Trade Designation | Product Function | Max Use |
| Sulfuric Acid 35% | Corrosion & Scale Control | 132mg/L |
| Sulfuric Acid 50% | Corrosion & Scale Control | 91mg/L |
| Sulfuric Acid 66' | Corrosion & Scale Control | 50mg/L |
| Sulfuric Acid 93% | Corrosion & Scale Control | 50mg/L |
| WSU Sulfuric Acid 35% | Corrosion & Scale Control | 132mg/L |
| WSU Sulfuric Acid 50% | Corrosion & Scale Control | 91mg/L |
| WSU Sulfuric Acid 66' | Corrosion & Scale Control | 50mg/L |
| WSU Sulfuric Acid 93% | Corrosion & Scale Control | 50mg/L |
|
Zinc Orthophosphate[1] [ZN] |
||
| Trade Designation | Product Function | Max Use |
| Aquagold 11 | Corrosion & Scale Control Corrosion Control |
20mg/L |
| Aquagold 13 | Corrosion & Scale Control | 16mg/L |
| Aquagold 15 | Corrosion & Scale Control | 15mg/L |
| PT-800 | Corrosion & Scale Control | 16mg/L |
| WSU 403 | Corrosion & Scale Control | 16mg/L |
| WSU 405 | Corrosion & Scale Control | 15mg/L |
| WSU 411 | Corrosion & Scale Control Corrosion Control |
20mg/L |
[1] Only products bearing the NSF Mark on the product, product packaging, and/or
documentation shipped with the product are Certified.
[ZN] Based on an evaluation of health effects data, the level of zinc in the finished
drinking water shall not exceed 2.0 mg/L.
|
||
Facility : Jackson, MI
|
Aluminum Chlorohydrate[AL] |
||
| Trade Designation | Product Function | Max Use |
| WSU FLOC 4000 | Coagulation & Flocculation | 250mg/L |
[AL] Based on an evaluation of health effects data, the level of aluminum in the finished
drinking water shall not exceed 2 mg/L.
|
||
|
Ferric Chloride[1] |
||
| Trade Designation | Product Function | Max Use |
| Ferric Chloride 38% | Coagulation & Flocculation | 250mg/L |
| WSU 38% Ferric Chloride | Coagulation & Flocculation | 250mg/L |
| WSU Ferric Chloride 38% | Coagulation & Flocculation | 250mg/L |
[1] Only products bearing the NSF Mark on the product, product packaging, and/or
documentation shipped with the product are Certified.
|
||
|
Fluorosilicic Acid |
||
| Trade Designation | Product Function | Max Use |
| Fluorosilicic Acid 23% | Fluoridation | 5mg/L |
| WSU 23% Fluorosilicic Acid | Fluoridation | 5mg/L |
| WSU Fluorosilicic Acid 23% | Fluoridation | 5mg/L |
|
Sodium Hypochlorite[1] [HY] |
||
| Trade Designation | Product Function | Max Use |
| WSU HYPOCHLORITE 125 | Disinfection & Oxidation | 65mg/L |
| WSU HYPOCHLORITE 125M | Disinfection & Oxidation | 65mg/L |
[1] Only products bearing the NSF Mark on the product, product packaging, and/or
documentation shipped with the product are Certified.
[HY] The residual levels of chlorine (hypochlorite ion and hypochlorous acid), chlorine
dioxide, chlorate ion, chloramine and disinfection by-products shall be monitored in the
finished drinking water to ensure compliance to all applicable regulations. Also,
reference the AWWA B300 (Hypochlorites) standard's Recommendations for the Handling and
Storage of Hypochlorite Solutions appendix for information on preservation techniques
for hypochlorite bleach in transit and storage.
|
||
Number of matching Manufacturers is 1
Number of matching Products is 171
Processing time was 0 seconds
