NSF Product and Service Listings

[AL] Based on an evaluation of health effects data, the level of aluminum in the finished
     drinking water shall not exceed 2 mg/L.

[AL] Based on an evaluation of health effects data, the level of aluminum in the finished
     drinking water shall not exceed 2 mg/L.

[1] This product is designed to be used off-line and flushed out prior to using the system
    for drinking water, following manufacturer's use instructions.
[2] The pH of the influent and effluent water should be monitored to ensure that all traces
    of the product have been removed before placing into service.

[PC] Polyacrylamide Products Certified by NSF International comply with 40 CFR 141.111
     requirements for percent monomer and dose.

[AL] Based on an evaluation of health effects data, the level of aluminum in the finished
     drinking water shall not exceed 2 mg/L.

[CL] The residual levels of chlorine (hypochlorite ion and hypochlorous acid), chlorine
     dioxide, chlorate ion, chloramine and disinfection by-products shall be monitored in the
     finished drinking water to ensure compliance to all applicable regulations.

[HY] The residual levels of chlorine (hypochlorite ion and hypochlorous acid), chlorine
     dioxide, chlorate ion, chloramine and disinfection by-products shall be monitored in the
     finished drinking water to ensure compliance to all applicable regulations. Also,
     reference the AWWA B300 (Hypochlorites) standard's Recommendations for the Handling and
     Storage of Hypochlorite Solutions appendix for information on preservation techniques
     for hypochlorite bleach in transit and storage.

[PO] The finished drinking water shall be monitored to ensure that levels of manganese

     do not exceed 0.05 mg/L.

[1] These products are designed to be flushed out prior to using the system for drinking
    water. Before being placed into service, the well is to be properly flushed according to
    the manufacturer's use instructions. Certification of these products is based on the
    well drilling model with the following assumptions:
    - The amount of well drilling fluid used is 3780 L (1000 U.S. gallons) to which the 
      drilling fluid has been added at the manufacturer's recommended level.
    - The aquifer contains 3.1 million liters of water (815,000 gallons) based on a 0.5 
      acre aquifer of 6.1 meter depth (20 ft.) and 25% porosity.
    - The bore hole is 61 meters in total depth (200 ft.), the screen is 6.1 meters in 
      length (20 ft.), and the bore hole is 25.4 cm. in diameter (10 in.).
    - The amount of well drilling fluid removed from the well during construction is equal 
      to the combined volumes of the casing and the screen, plus an additional amount 
      removed through the well disinfection and development (90% removed).
    - This product should not be used in constructing wells in highly porous formations, 
      such as cavernous limestone.

[1] These products are designed to be flushed out prior to using the system for drinking
    water. Before being placed into service, the well is to be properly
    flushed according to the manufacturer's use instructions. Certification of these
    products is based on the well drilling model with the following assumptions:
    - The amount of well drilling fluid used is 3780 L (1000 U.S. gallons) to which the
    drilling fluid has been added at the manufacturer's recommended level.
    - The aquifer contains 3.1 million liters of water (815,000 gallons) based on a 0.5 acre
    aquifer of 6.1 meter depth (20 ft.) and 25% porosity.
    - The bore hole is 61 meters in total depth (200 ft.), the screen is 6.1 meters in
    length (20 ft.), and the bore hole is 25.4 cm. in diameter (10 in.).
    - The amount of well drilling fluid removed from the well during construction is equal
    to the combined volumes of the casing and the screen, plus an additional amount removed
    through the well disinfection and development (90% removed).
    - This product should not be used in constructing wells in highly porous formations,
    such as cavernous limestone.

[AL] Based on an evaluation of health effects data, the level of aluminum in the finished
     drinking water shall not exceed 2 mg/L.

[2] This product is designed to be used off-line and flushed out prior to using the system
    for drinking water, following manufacturer's use instructions.

[AL] Based on an evaluation of health effects data, the level of aluminum in the finished
     drinking water shall not exceed 2 mg/L.

[1] This product contains sulfite.
   Sulfites have been known to cause potentially lethal
    allergic reactions in sulfite-sensitive individuals.
   The maximum recommended allowable
    residual sulfite level in the finished drinking water is 100 ppb (0.1 mg/L).

[HY] The residual levels of chlorine (hypochlorite ion and hypochlorous acid), chlorine
     dioxide, chlorate ion, chloramine and disinfection by-products shall be monitored in the
     finished drinking water to ensure compliance to all applicable regulations. Also,
     reference the AWWA B300 (Hypochlorites) standard's Recommendations for the Handling and
     Storage of Hypochlorite Solutions appendix for information on preservation techniques
     for hypochlorite bleach in transit and storage.