NSF Product and Service Listings

These NSF Official Listings are current as of Thursday, April 25, 2024 at 12:15 a.m. Eastern Time. Please contact NSF to confirm the status of any Listing, report errors, or make suggestions.

Alert: NSF is concerned about fraudulent downloading and manipulation of website text. Always confirm this information by clicking on the below link for the most accurate information: http://info.nsf.org/Certified/PwsComponents/Listings.asp?



NSF/ANSI/CAN 61
Drinking Water System Components - Health Effects

NOTE: Unless otherwise indicated for Materials, Certification is only for the Water Contact Material shown in the Listing. Click here for a list of Abbreviations used in these Listings. Click here for the definitions of Water Contact Temperatures denoted in these Listings. Products certified to NSF/ANSI/CAN 61 comply with the health effects criteria in NSF/ANSI/CAN 600.


 
14403436 Canada Inc. 
Unit 1-146 West Beaver Creek Road
Richmond Hill, ON L4B 1C2 
Canada 
86 755 8418 3343


Facility : # 1 China

Mechanical Devices

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Water Meters
Rhino Water valve (RH-WV2021) 3/4" D. HOT MLTPL



 
3M / Electrical Markets Division 
3M Center, Building 201-2C-11
St. Paul, MN 55144 
United States 
651-736-9030
Visit this company's website


Facility : Angleton, TX

Protective (Barrier) Materials

    Water Water
  Water Contact Contact Contact
Trade Designation Size Restriction Temp Material

Coatings - Fittings
3M Scotchkote Fusion Bonded Epoxy Coating 6233W 11G[1] >= 1/2" D. HOT PEC
3M Scotchkote Fusion Bonded Epoxy Coating 6233W 4G[1] >= 1/2" D. HOT PEC
3M Scotchkote Fusion Bonded Epoxy Coating 6233W 8G[1] >= 1/2" D. HOT PEC
ScotchKote 134[4] >= 1/2"[5] D. HOT PEC
Scotchkote 206N[2] >= 4" D. HOT PEC
Scotchkote 206N Extra LG[2] >= 4" D. HOT PEC
Scotchkote 206N Fluid Bed[2] >= 4" D. HOT PEC
Scotchkote 206N Long Gel[2] >= 4" D. HOT PEC

[1] Colors: Dark Green
    Number of Coats: 1
    Maximum Field Use Dry Film Thickness (in mils): 50
    Maximum thinner: None
    Final Cure Time and Temperature: 6233W 4G: 30-45 seconds at 450°F; 6233W 8G: 60-90
    seconds at 450°F; 6233W 11G: 90-120 seconds at 450°F
    Special Comments: Preheat part to 425° - 488° F before application of powder.
[2] Number of Coats: 1
    Maximum Field Use Dry Film Thickness (in mils): 60
    Final Cure Time and Temperature: 206N: 10 minutes at 400°F; 206N Extra LG: 16 minutes at
    400°F; 206N Fluid Bed: 10 minutes at 400°F; 206N Long Gel: 10 minutes at 400°F
[4] Number of Coats: 1
    Sequence of Coats: N/A
    Maximum Field Use Dry Film Thickness (in mils): 60
    Maximum Thinner: None
    Final Cure Time and Temperature: 25 minutes at 425° F
[5] Certified for a maximum surface area to volume ratio of 122.1 sq. in./L for pump end use.

Coatings - Pipe
3M Scotchkote Fusion Bonded Epoxy Coating 6233W 11G[1] >= 1/2" D. HOT PEC
3M Scotchkote Fusion Bonded Epoxy Coating 6233W 4G[1] >= 1/2" D. HOT PEC
3M Scotchkote Fusion Bonded Epoxy Coating 6233W 8G[1] >= 1/2" D. HOT PEC
ScotchKote 134[4] >= 1/2"[5] D. HOT PEC
Scotchkote 206N[2] >= 4" D. HOT PEC
Scotchkote 206N Extra LG[2] >= 4" D. HOT PEC
Scotchkote 206N Fluid Bed[2] >= 4" D. HOT PEC
Scotchkote 206N Long Gel[2] >= 4" D. HOT PEC

[1] Colors: Dark Green
    Number of Coats: 1
    Maximum Field Use Dry Film Thickness (in mils): 50
    Maximum thinner: None
    Final Cure Time and Temperature: 6233W 4G: 30-45 seconds at 450°F; 6233W 8G: 60-90
    seconds at 450°F; 6233W 11G: 90-120 seconds at 450°F
    Special Comments: Preheat part to 425° - 488° F before application of powder.
[2] Number of Coats: 1
    Maximum Field Use Dry Film Thickness (in mils): 60
    Final Cure Time and Temperature: 206N: 10 minutes at 400°F; 206N Extra LG: 16 minutes at
    400°F; 206N Fluid Bed: 10 minutes at 400°F; 206N Long Gel: 10 minutes at 400°F
[4] Number of Coats: 1
    Sequence of Coats: N/A
    Maximum Field Use Dry Film Thickness (in mils): 60
    Maximum Thinner: None
    Final Cure Time and Temperature: 25 minutes at 425° F
[5] Certified for a maximum surface area to volume ratio of 122.1 sq. in./L for pump end use.

Coatings - Pump
ScotchKote 134[4] [5] D. HOT PEC
Scotchkote 206N[2] [3] >= 2" D. HOT PEC
Scotchkote 206N Extra LG[2] [3] >= 2" D. HOT PEC
Scotchkote 206N Fluid Bed[2] [3] >= 2" D. HOT PEC
Scotchkote 206N Long Gel[2] [3] >= 2" D. HOT PEC

[2] Number of Coats: 1
    Maximum Field Use Dry Film Thickness (in mils): 60
    Final Cure Time and Temperature: 206N: 10 minutes at 400°F; 206N Extra LG: 16 minutes at
    400°F; 206N Fluid Bed: 10 minutes at 400°F; 206N Long Gel: 10 minutes at 400°F
[3] Certified for a maximum surface area to volume ratio of 122.1 sq. in./L. for pump end
    use.
[4] Number of Coats: 1
    Sequence of Coats: N/A
    Maximum Field Use Dry Film Thickness (in mils): 60
    Maximum Thinner: None
    Final Cure Time and Temperature: 25 minutes at 425° F
[5] Certified for a maximum surface area to volume ratio of 122.1 sq. in./L for pump end use.

Coatings - Tank
ScotchKote 134[4] >= 5 gal. D. HOT PEC
Scotchkote 206N[2] >= 5 gal. D. HOT PEC
Scotchkote 206N Extra LG[2] >= 5 gal. D. HOT PEC
Scotchkote 206N Fluid Bed[2] >= 5 gal. D. HOT PEC
Scotchkote 206N Long Gel[2] >= 5 gal. D. HOT PEC

[2] Number of Coats: 1
    Maximum Field Use Dry Film Thickness (in mils): 60
    Final Cure Time and Temperature: 206N: 10 minutes at 400°F; 206N Extra LG: 16 minutes at
    400°F; 206N Fluid Bed: 10 minutes at 400°F; 206N Long Gel: 10 minutes at 400°F
[4] Number of Coats: 1
    Sequence of Coats: N/A
    Maximum Field Use Dry Film Thickness (in mils): 60
    Maximum Thinner: None
    Final Cure Time and Temperature: 25 minutes at 425° F

Coatings - Valve
3M Scotchkote Fusion Bonded Epoxy Coating 6233W 11G[1] >= 1/2" D. HOT PEC
3M Scotchkote Fusion Bonded Epoxy Coating 6233W 4G[1] >= 1/2" D. HOT PEC
3M Scotchkote Fusion Bonded Epoxy Coating 6233W 8G[1] >= 1/2" D. HOT PEC
ScotchKote 134[4] >= 1/2"[5] D. HOT PEC
Scotchkote 206N[2] >= 2" D. HOT PEC
Scotchkote 206N Extra LG[2] >= 2" D. HOT PEC
Scotchkote 206N Fluid Bed[2] >= 2" D. HOT PEC
Scotchkote 206N Long Gel[2] >= 2" D. HOT PEC

[1] Colors: Dark Green
    Number of Coats: 1
    Maximum Field Use Dry Film Thickness (in mils): 50
    Maximum thinner: None
    Final Cure Time and Temperature: 6233W 4G: 30-45 seconds at 450°F; 6233W 8G: 60-90
    seconds at 450°F; 6233W 11G: 90-120 seconds at 450°F
    Special Comments: Preheat part to 425° - 488° F before application of powder.
[2] Number of Coats: 1
    Maximum Field Use Dry Film Thickness (in mils): 60
    Final Cure Time and Temperature: 206N: 10 minutes at 400°F; 206N Extra LG: 16 minutes at
    400°F; 206N Fluid Bed: 10 minutes at 400°F; 206N Long Gel: 10 minutes at 400°F
[4] Number of Coats: 1
    Sequence of Coats: N/A
    Maximum Field Use Dry Film Thickness (in mils): 60
    Maximum Thinner: None
    Final Cure Time and Temperature: 25 minutes at 425° F
[5] Certified for a maximum surface area to volume ratio of 122.1 sq. in./L for pump end use.



 
3R Valve, LLC 
29299 Madison Road
Echo, OR 97826 
United States 
541-376-8107
Visit this company's website


Facility : Echo, OR

Mechanical Devices

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Valves [G]
ASR (Aqua System Recovery) Valve[1] 5" - 14" CLD 23 MLTPL

[1] Certified for use in municipal wells in conjunction with a submersible pump. Not
    Certified for residential use.
[G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for
    “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state
    laws and the U.S. Safe Drinking Water Act.

    



 
4 Sealing Italia SRL 
Vicolo Stretto 2
25030 Rudiano, Brescia 
Italy 
39 391 348 5439
Visit this company's website


Facility : 4 Sealing - Brescia

Joining and Sealing Materials

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Gasket/Sealing Materials
EXX50 [1] C. HOT EPDM
EXX60 [1] C. HOT EPDM
EXX70 [1] C. HOT EPDM
EXX90 [1] C. HOT EPDM
NXX50[2] [1] C. HOT NBR
NXX60[2] [1] C. HOT NBR
NXX70[2] [1] C. HOT NBR
NXX90[2] [1] C. HOT NBR

[1] Certified for a maximum surface area to volume ratio of 2.0 square inches/L.
[2] This product has also been evaluated for use in Mechanical Plumbing Device applications
    with a maximum use restriction of 0.8 square inches/L.

O-Rings
EXX50 [1] C. HOT EPDM
EXX60 [1] C. HOT EPDM
EXX70 [1] C. HOT EPDM
EXX90 [1] C. HOT EPDM
NXX50[2] [1] C. HOT NBR
NXX60[2] [1] C. HOT NBR
NXX70[2] [1] C. HOT NBR
NXX90[2] [1] C. HOT NBR

[1] Certified for a maximum surface area to volume ratio of 2.0 square inches/L.
[2] This product has also been evaluated for use in Mechanical Plumbing Device applications
    with a maximum use restriction of 0.8 square inches/L.



5Elem Hi-Tech Corporation 
No.16, Jiangqin Road
Economic Development Zone 
Jiangyan, Jiangsu 225500 
China 
86 523 8881 5055 
Visit this company's website


Facility : Jiangsu, China

Pipes and Related Products

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Pipe
Nordiliner 3/4"-3.5" & 4.5"-12" CLD 23 PUR



 
A. O. Smith Enterprises Ltd. 
768 Erie Street
P.O. Box 310 
Stratford, ON N5A 6T3 
Canada 
519-271-5800


Facility : Stratford, Ontario, Canada

Mechanical Devices

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Pressurized Water Storage Tanks[1] [G]
A O Smith (LPT Prefix) 119 gal. CLD 23 MLTPL
A O Smith ProMax (PM Prefix) 14 - 119 gal. CLD 23 MLTPL
A Y McDonald (16 Prefix) 119 gal. CLD 23 MLTPL
Altamira Pro X/XL 20 - 119 gal. CLD 23 MLTPL
American Water Heater (APT Prefix) 14 - 119 gal. CLD 23 MLTPL
Driller Services (DST/DSI Prefix) >= 65 gal. CLD 23 MLTPL
Global Pump (GPE Prefix) >= 85 gal. CLD 23 MLTPL
Gould Pumps Hydro Pro Water Systems Tanks (V Prefix and MP or PST Suffix) 14 - 20 gal. CLD 23 MLTPL
Gould Pumps Hydro Pro Water Systems Tanks (V Prefix) 14 - 119 gal. CLD 23 MLTPL
PermaTank (SBD/SBDT Prefix) >= 86 gal. CLD 23 MLTPL
Pump Pro (PP Prefix and MP or PST Suffix) 14 - 20 gal. CLD 23 MLTPL
Pump Pro (PP Prefix) >= 14 gal. CLD 23 MLTPL
Reliance (PMD Prefix) 119 gal. CLD 23 MLTPL
State (MPT Prefix & SSB Prefix) >= 85 gal. CLD 23 MLTPL
Trident (TD Prefix and MP or PST Suffix) 14 - 20 gal. CLD 23 MLTPL
Trident Ultra (TDU Prefix and MP or PST Suffix ) >= 14 gal. CLD 23 MLTPL
Trident Ultra (TDU and TD Prefix) >= 14 gal. CLD 23 MLTPL
Xylem CentriPro T Water Sytem Tanks 14 - 119 gal. CLD 23 MLTPL
Xylem CentriPro TP Water Systems Tanks 14 - 119 gal. CLD 23 MLTPL
Xylem Hydro Pro Water System Tanks (V Prefix) 14 - 119 gal. CLD 23 MLTPL
Xylem Hydro Pro Water System Tanks (V prefix and MP or PST suffix) 14 - 20 gal. CLD 23 MLTPL

[1] Product also complies with NSF/ANSI 372.
[G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for
    “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state
    laws and the U.S. Safe Drinking Water Act.

    

Thermal Expansion Tanks[1] [G]
Bell and Gossett (Prefix PT)[2] 14 - 86 gal. D. HOT MLTPL

[1] Product also complies with NSF/ANSI 372.
[2] Suffixes:
    blank 
    B   - Buried 
    EX  - Base extension 
    MP  - Mounted pump 
    P   - Pipe mounted 
    PST - Pump system tank
    S
[G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for
    “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state
    laws and the U.S. Safe Drinking Water Act.

    



 
A. W. Chesterton Co. 
860 Salem Street
Groveland, MA 01834 
United States 
978-469-6446


Facility : Groveland, MA

Mechanical Devices

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Miscellaneous Process Devices/Components[1]
150 Non-Split Cartridge Seal[G] [2] D. HOT MLTPL
1510 Non-Split Cartridge Seal[G] [2] D. HOT MLTPL
155 Non-Split Cartridge Seal[G] [2] D. HOT MLTPL
1725A[3] [G] D. HOT PTFE
180 Non-Split Cartridge Seal[G] [2] D. HOT MLTPL
1810 Non-Split Cartridge Seal[G] [2] D. HOT MLTPL
442 Split Mechanical Seal[G] [2] D. HOT MLTPL
442C Split Mechanical Seal[G] [2] D. HOT MLTPL
S10 Non-Split Cartridge Seal[G] [2] D. HOT MLTPL
Single Non-Split Cartridge Seals[G] [2] D. HOT MLTPL
Spare Part Kit (SPK)[G] [2] D. HOT MLTPL

[1] Only products bearing the NSF Mark on the product, product packaging, and/or
    documentation shipped with the product are Certified.
[2] Certified for mechanical seals for use with pump shafts ranging from 1" - 12" in
    diameter.  Certified for equivalent metric sizes.
[3] Certified for use as a packing material in pumps with shaft diameters >= 0.625".
[G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for
    “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state
    laws and the U.S. Safe Drinking Water Act.

    


Protective (Barrier) Materials

    Water Water
  Water Contact Contact Contact
Trade Designation Size Restriction Temp Material

Coatings - Fittings
ARC S1 PW BLU[1] >= 1/2" CLD 23 EPOXY
ARC S1 PW HB WH[2] >= 18" CLD 23 EPOXY
ARC S1 PW WH[1] >= 1/2" CLD 23 EPOXY

[1] Colors: Blue, White
    Number of coats: 3
    Maximum field use dry film thickness (in mils): 45 (15 mils/coat)
    Recoat cure time and temperature: 6 hours at 77°F
    Final cure time and temperature: 7 days at 77°F
    Special Comments: Mix ratio of Part A:B is 2:1 by volume
[2] Colors: White
    Number of coats: 1-3
    Maximum field use dry film thickness (in mils): 240 (80 mils/coat)
    Recoat cure time and temperature: 6 hours at 77°F
    Final cure time and temperature: 7 days at 77°F
    Special Comments: Mix ratio of Part A:B is 2:1 by volume. Minimum mil thickness is 1
    coat at 80 mils.

Coatings - Pump
ARC S1 PW BLU[1] >= 1/2" CLD 23 EPOXY
ARC S1 PW WH[1] >= 1/2" CLD 23 EPOXY

[1] Colors: Blue, White
    Number of coats: 3
    Maximum field use dry film thickness (in mils): 45 (15 mils/coat)
    Recoat cure time and temperature: 6 hours at 77°F
    Final cure time and temperature: 7 days at 77°F
    Special Comments: Mix ratio of Part A:B is 2:1 by volume

Coatings - Pipe
ARC S1 PW BLU[1] >= 1/2" CLD 23 EPOXY

[1] Colors: Blue, White
    Number of coats: 3
    Maximum field use dry film thickness (in mils): 45 (15 mils/coat)
    Recoat cure time and temperature: 6 hours at 77°F
    Final cure time and temperature: 7 days at 77°F
    Special Comments: Mix ratio of Part A:B is 2:1 by volume
[2] Colors: White
    Number of coats: 1-3
    Maximum field use dry film thickness (in mils): 240 (80 mils/coat)
    Recoat cure time and temperature: 6 hours at 77°F
    Final cure time and temperature: 7 days at 77°F
    Special Comments: Mix ratio of Part A:B is 2:1 by volume. Minimum mil thickness is 1
    coat at 80 mils.

Coatings - Valve
ARC S1 PW WH[1] >= 1/2" CLD 23 EPOXY
ARC S1 PW BLU[1] >= 1/2" CLD 23 EPOXY

[1] Colors: Blue, White
    Number of coats: 3
    Maximum field use dry film thickness (in mils): 45 (15 mils/coat)
    Recoat cure time and temperature: 6 hours at 77°F
    Final cure time and temperature: 7 days at 77°F
    Special Comments: Mix ratio of Part A:B is 2:1 by volume

Coatings - Pipe
ARC S1 PW HB WH[2] >= 18" CLD 23 EPOXY
ARC S1 PW WH[1] >= 1/2" CLD 23 EPOXY

[1] Colors: Blue, White
    Number of coats: 3
    Maximum field use dry film thickness (in mils): 45 (15 mils/coat)
    Recoat cure time and temperature: 6 hours at 77°F
    Final cure time and temperature: 7 days at 77°F
    Special Comments: Mix ratio of Part A:B is 2:1 by volume
[2] Colors: White
    Number of coats: 1-3
    Maximum field use dry film thickness (in mils): 240 (80 mils/coat)
    Recoat cure time and temperature: 6 hours at 77°F
    Final cure time and temperature: 7 days at 77°F
    Special Comments: Mix ratio of Part A:B is 2:1 by volume. Minimum mil thickness is 1
    coat at 80 mils.

Coatings - Tank
ARC S1 PW BLU[1] >= 1,500 gal. CLD 23 EPOXY
ARC S1 PW HB WH[2] >= 1,500 gal. CLD 23 EPOXY
ARC S1 PW WH[1] >= 1,500 gal. CLD 23 EPOXY

[1] Colors: Blue, White
    Number of coats: 3
    Maximum field use dry film thickness (in mils): 45 (15 mils/coat)
    Recoat cure time and temperature: 6 hours at 77°F
    Final cure time and temperature: 7 days at 77°F
    Special Comments: Mix ratio of Part A:B is 2:1 by volume
[2] Colors: White
    Number of coats: 1-3
    Maximum field use dry film thickness (in mils): 240 (80 mils/coat)
    Recoat cure time and temperature: 6 hours at 77°F
    Final cure time and temperature: 7 days at 77°F
    Special Comments: Mix ratio of Part A:B is 2:1 by volume. Minimum mil thickness is 1
    coat at 80 mils.



 
A. W. Chesterton Co. 
860 Salem Street
Groveland, MA 01834 
United States 
978-469-6446
Visit this company's website


Facility : # 1 USA

Joining and Sealing Materials

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Patching Materials
ARC 5ES [1] C. HOT EPOXY

[1] The exposed surface area of each sealant in a household distribution system
    should not exceed 1.3 sq. cm/L or .2 sq. in/L.



 
A.O. Smith Su Teknolojileri A.S. 
Ikitelli O.S.B.Mh.Marmara D Blok Sk.
No:2-3, Küçükçekmece-Ikitelli 
34303 Istanbul 
Türkiye 
90 212 444 1646
Visit this company's website


Facility : # 3 China

Mechanical Devices

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Reverse Osmosis Element[1] [2] [3]
BW-4040 4" x 40" CLD 23 MLTPL
BW-8040 8" x 40" CLD 23 MLTPL
ULP-4021 4" x 21" CLD 23 MLTPL
ULP-4040 4" x 40" CLD 23 MLTPL
ULP-4040HR 4" x 40" CLD 23 MLTPL
ULP-4040MR 4" x 40" CLD 23 MLTPL
ULP-8040 8" x 40" CLD 23 MLTPL

[1] Size is expressed as Diameter x length.
[2] BW-8040 and ULP-8040 models are Certified for a minimum daily flow of 10000 gallons.
    BW-4040 model is Certified for a minimum daily flow of 2400 gallons.
    ULP-4040 model is Certified for a minimum daily flow of 2600 gallons.
    ULP-4040MR model is Certified for a minimum daily flow of 2200 gallons.
    ULP-4040HR model is Certified for a minimum daily flow of 1800 gallons.
    ULP-4021 model is Certified for a minimum daily flow of 950 gallons.
[3] Models require the following flushing procedure:
    BW-4040, ULP-4040, ULP-4040MR, ULP-4040HR and ULP-4021 require a 4 gpm flush for 24
    hours using tap water.
    BW-8040 and ULP-8040 require a 15 gpm flush for 24 hours using tap water.



 
A.R. Thomson Group 
3420 189th Street
Surrey, BC V32 1A7 
Canada 
604-507-6050
Visit this company's website


Facility : # 1 Canada

Joining and Sealing Materials

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Gasket/Sealing Materials
Thomson Multipac-6000 [1] C. HOT OTHER
Thomson Multipac-6000 [2] CLD 23 OTHER

[1] Certified for a maximum surface area to volume ratio of 0.3 sq. in./L when used at
    Commercial Hot (82°C) temperature.
[2] Certified for a maximum surface area to volume ratio of 0.8 sq. in./L when used at Cold
    (23°C) temperature.



 
A.R. Thomson Group 
3420 189th Street
Surrey, BC V3Z 1A7 
Canada 
604-507-6050
Visit this company's website


Facility : # 1 Canada

Joining and Sealing Materials

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Gasket/Sealing Materials
Thomson 4500 >= 3" CLD 23 EPDM
Thomson MultiPac 6000 [1] C. HOT OTHER
Thomson MultiPac 6000 [2] CLD 23 OTHER

[1] Certified for a maximum surface area to volume ratio of 0.3 sq. in./L when used at
    Commercial Hot (82°C) temperature.
[2] Certified for a maximum surface area to volume ratio of 0.8 sq. in./L when used at Cold
    (23°C) temperature.



 
A.T. Gomma Guarnizioni Industriali S.R.L. 
Via Mearolo, 3/D
24060 Foresto Sparso 
Italy 
39 035 930 254
Visit this company's website


Facility : Foresto Sparso, Italy

Joining and Sealing Materials

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Gasket/Sealing Materials[1] [G]
EX70LC (EPDM 70 PEROX) [2] C. HOT EPDM

[1] This product has also been evaluated for use in Mechanical Plumbing Device applications
    with a maximum use restriction of 2.0 square inches/L.
[2] Certified for a maximum surface area to volume ration of 2.0 square inches/L.
[G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for
    “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state
    laws and the U.S. Safe Drinking Water Act.

    

O-Rings[1] [G]
EX70LC (EPDM 70 PEROX) [2] C. HOT EPDM

[1] This product has also been evaluated for use in Mechanical Plumbing Device applications
    with a maximum use restriction of 2.0 square inches/L.
[2] Certified for a maximum surface area to volume ration of 2.0 square inches/L.
[G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for
    “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state
    laws and the U.S. Safe Drinking Water Act.

    



 
A.T.P. Avanzate Tecnologie Plastiche SRL 
Via dell'Industria, 3
76121 Barletta (BT) 
Italy 
39 08 835 33167
Visit this company's website


Facility : Barletta (BT), Italy

Mechanical Devices

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Service Saddles[1] [G]
TORO 25 63 mm - 250 mm D. HOT MLTPL

[1] Saddle PN25
    SDL 6320 (63 x 20 mm)
    SDL 6325 (63 x 25 mm)
    SDL 6332 (63 x 32 mm)
    SDL 7520 (75 x 20 mm)
    SDL 7525 (75 x 25 mm)
    SDL 7532 (75 x 32 mm)
    SDL 9025 (90 x 25 mm)
    SDL 9032 (90 x 32 mm)
    SDL 9040 (90 x 40 mm)
    SDL 11032 (110 x 32 mm)
    SDL 11040 (110 x 40 mm)
    SDL 11050 (110 x 50 mm)
    SDL 12540 (125 x 40 mm)
    SDL 12550 (125 x 50 mm)
    SDL 12563 (125 x 63 mm)
    SDL 16040 (160 x 40 mm)
    SDL 16050 (160 x 50 mm)
    SDL 16063 (160 x 63 mm)
    SDL 20050 (200 x 50 mm)
    SDL 20063 (200 x 63 mm)
    SDL 20075 (200 x 75 mm)
    SDL 20090 (200 x 90 mm)
    SDL 25063 (250 x 63 mm)
    SDL 25075 (250 x 75 mm)
    SDL 25090 (250 x 90 mm)
    SDL 250110 (250 x 110 mm)
       
    Threaded Saddle PN25
    SDF 6320 (63 mm x 1/2")
    SDF 6325 (63 mm x 3/4")
    SDF 7520 (75 mm x 1/2")
    SDF 7525 (75 mm x 3/4")
    SDF 9020 (90 mm x 1/2")
    SDF 9025 (90 mm x 3/4")
    SDF 11020 (110 mm x 1/2")
    SDF 11025 (110 mm x 3/4")
    SDF 11032 (110 mm x 1")
[G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for
    “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state
    laws and the U.S. Safe Drinking Water Act.

    


Pipes and Related Products

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Fittings[1] [2] [G]
TORO 25 20 mm - 250 mm D. HOT PP

[1] Configurations include:
        
    Swan Neck PN20
    SOP 20 A20 (20 x 20 mm)
    SOP 25 A20 (25 x 25 mm)
    SOP 32 A20 (32 x 32 mm)
         
    Swan Neck Female - Female PN25
    SFF 2020 (20 x 20 mm)
    SFF 2525 (25 x 25 mm)
      
    Swan Neck Short Female - Female PN25
    SFC 2020 (20 x 20 mm)
    SFC 2525 (25 x 25 mm) 
       
    Socket PN25
    MAN 20 (20 x 20 mm)
    MAN 25 (25 x 25 mm)
    MAN 32 (32 x 32 mm)
    MAN 40 (40 x 40 mm)
    MAN 50 (50 x 50 mm)
    MAN 63 (63 x 63 mm)
    MAN 75 (75 x 75 mm)
    MAN 90 (90 x 90 mm)
    MAN 110 (110 x 110 mm)
    MAN 125 (125 x 125 mm)
    MAN 160 (160 x 160 mm)
    
    90° Elbow PN25
    CUV 20 (20 x 20 mm)
    CUV 25 (25 x 25 mm)
    CUV 32 (32 x 32 mm)
    CUV 40 (40 x 40 mm)
    CUV 50 (50 x 50 mm)
    CUV 63 (63 x 63 mm)
    CUV 75 (75 x 75 mm)
    CUV 90 (90 x 90 mm)
    CUV 110 (110 x 110 mm)
    CUV 125 (125 x 125 mm)
    CUV 160 (160 x 160 mm)
    CUV 160 T (160 x 160 mm)
    CUV 200 T (200 x 200 mm)
    CUV 250 T (250 x 250 mm)
        
    45° Elbow PN25
    CUQ 20 (20 x 20 mm)
    CUQ 25 (25 x 25 mm)
    CUQ 32 (32 x 32 mm)
    CUQ 40 (40 x 40 mm)
    CUQ 50 (50 x 50 mm)
    CUQ 63 (63 x 63 mm)
    CUQ 75 (75 x 75 mm)
    CUQ 90 (90 x 90 mm)
    CUQ 110 (110 x 110 mm)
    CUQ125 (125 x 125 mm)
    CUQ 160 (160 x 160 mm)
    CUQ 160 T (160 x 160 mm)
    CUQ 200 T (200 x 200 mm)
    CUQ 250 T (250 x 250 mm)
      
    90° Elbow M/F PN25
    CMF 20 (20 x 20 mm)
    CMF 25 (25 x 25 mm)
      
    Reduced 90° Elbow PN25
    CUR 2520 (25 x 20 mm)
    CUR 3220 (32 x 20 mm)
    CUR 3225 (32 x 25 mm)
      
    Reducing Bush M/F PN25
    RDZ 2520 (25 x 20 mm)
    RDZ 3220 (32 x 20 mm)
    RDZ 3225 (32 x 25 mm)
    RDZ 4020 (40 x 20 mm)
    RDZ 4025 (40 x 25 mm)
    RDZ 4032 (40 x 32 mm)
    RDZ 5020 (50 x 20 mm)
    RDZ 5025 (50 x 25 mm)
    RDZ 5032 (50 x 32 mm)
    RDZ 5040 (50 x 40 mm)
    RDZ 6320 (63 x 20 mm)
    RDZ 6325 (63 x 25 mm)
    RDZ 6332 (63 x 32 mm)
    RDZ 6340 (63 x 40 mm)
    RDZ 6350 (63 x 50 mm)
       
    Reducing Bush F/F PN25
    RDF 2520 (25 x 20 mm)
    RDF 3220 (32 x 20 mm)
    RDF 3225 (32 x 25 mm)
    RDF 4020 (40 x 20 mm)
    RDF 4025 (40 x 25 mm)
    RDF 4032 (40 x 32 mm)
    RDF 5020 (50 x 20 mm)
    RDF 5025 (50 x 25 mm)
    RDF 5032 (50 x 32 mm)
    RDF 5040 (50 x 40 mm)
    RDF 6320 (63 x 20 mm)
    RDF 6325 (63 x 25 mm)
    RDF 6332 (63 x 32 mm)
    RDF 6340 (63 x 40 mm)
    RDF 6350 (63 x 50 mm)
    RDF 7540 (75 x 40 mm)
    RDF 7550 (75 x 50 mm)
    RDF 7563 (75 x 63 mm)
    RDF 9050 (90 x 50 mm)
    RDF 9063 (90 x 63 mm)
    RDF 9075 (90 x 75 mm)
    RDF 11063 (110 x 63 mm)
    RDF 11075 (110 x 75 mm)
    RDF 11090 (110 x 90 mm)
    RDF 125110 (125 x 110 mm)
    RDF 160110 (160 x 110 mm)
    RDF 160125 (160 x 125 mm)
    RDT 200 160 (200 x 160 mm)
    RDT 250 200 (250 x 200 mm)
    RDT 250 160 (250 x 160 mm)
    
    Cap PN25
    TAC 20 (20 mm)
    TAC 25 (25 mm)
    TAC 32 (32 mm)
    TAC 40 (40 mm)
    TAC 50 (50 mm)
    TAC 63 (63 mm)
    TAC 75 (75 mm)
    TAC 90 (90 mm)
    TAC 110 (110 mm)
    TAC 125 (125 mm)
    TAC 160 T (160 mm)
    TAC 200 T (200 mm)
    TAC 250 T (250 mm)
       
    Tee PN25
    TEN 20 (20 x 20 x 20 mm)
    TEN 25 (25 x 25 x 25 mm)
    TEN 32 (32 x 32 x 32 mm)
    TEN 40 (40 x 40 x 40 mm)
    TEN 50 (50 x 50 x 50 mm)
    TEN 63 (63 x 63 x 63 mm)
    TEN 75 (75 x 75 x 75 mm)
    TEN 90 (90 x 90 x 90 mm)
    TEN 110 (110 x 110 x 110 mm)
    TEN 125 (125 x 125 x 125 mm)
    TEN 160 (160 x 160 x 160 mm)
    TEN 160 T (160 x 160 x 160 mm)
    TEN 200 T (200 x 200 x 200 mm)
    TEN 250 T (250 x 250 x 250 mm)
    
    Reducing Tee PN25
    TER 2520 (25 x 20 x 25 mm)
    TER 2521 (25 x 20 x 20 mm)
    TER 3220 (32 x 20 x 32 mm)
    TER 3225 (32 x 25 x 32 mm)
    TER 4020 (40 x 20 x 40 mm)
    TER 4025 (40 x 25 x 40 mm)
    TER 4032 (40 x 32 x 40 mm)
    TER 5020 (50 x 20 x 50 mm)
    TER 5025 (50 x 25 x 50 mm)
    TER 5032 (50 x 32 x 50 mm)
    TER 5040 (50 x 40 x 50 mm)
    TER 6320 (63 x 20 x 63 mm)
    TER 6325 (63 x 25 x 63 mm)
    TER 6332 (63 x 32 x 63 mm)
    TER 6340 (63 x 40 x 63 mm)
    TER 6350 (63 x 50 x 63 mm)
    TER 7540 (75 x 40 x 75 mm)
    TER 7550 (75 x 50 x 75 mm)
    TER 7563 (75 x 63 x 75 mm)
    TER 9050 (90 x 50 x 90 mm)
    TER 9063 (90 x 63 x 90 mm)
    TER 9075 (90 x 75 x 90 mm)
    TER 11063 (110 x 63 x 110 mm)
    TER 11075 (110 x 75 x 110 mm)
    TER 11090 (110 x 90 x 110 mm)
    TER 125110 (125 x 110 x 125 mm)
    TER 160110 (160 x 110 x 160 mm)
       
    Cross PN25
    TEQ 20 (20 x 20 x 20 x 20 mm)
        
    Union PN10
    UNI 2020 (20 x 20 mm)
    UNI 2525 (25 x 25 mm)
    UNI 3232 (32 x 32mm)
    UNI 4040 (40 x 40 mm)
    UNI 5050 (50 x 50 mm)
    UNI 6363 (63 x 63 mm)
[2] Stub End
    CTL 32 (32 mm)
    CTL 40 (40 mm)
    CTL 50 (50 mm)
    CTL 63 (63 mm)
    CTL 75 (75 mm)
    CTL 90 (90 mm)
    CTL 110 (110 mm)
    CTL 125 (125 mm)
    CTL 160 (160 mm)
    CTL 160 T (160 mm)
    CTL 200 T (200 mm)
    CTL 250 T (250 mm)
       
    Electrofusion Socket
    MAE 63 (63 x 63 mm)
    MAE 75 (75 x 75 mm)
    MAE 90 (90 x 90 mm)
    MAE 110 (110 x 110 mm)
    MAE 125 (125 x 125 mm)
    MAE 160 (160 x 160 mm)
    MAE 200 (200 x 200 mm)
    MAE 250 (250 x 250 mm)
[G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for
    “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state
    laws and the U.S. Safe Drinking Water Act.

    

Fittings, Non-Repeating[3] [G]
TORO 25 20 mm - 110 mm D. HOT PP

[3] Configurations include:
        
    Male Adapter Threaded Female PN25
    GFF 3220 (32 mm x 1/2")
        
    90° Threaded Elbow PN25 - Female
    CFF 2020 (20 mm x 1/2")
    CFF 2025 (20 mm x 3/4")
    CFF 2520 (25 mm x 1/2")
    CFF 2525 (25 mm x 3/4")
    CFF 3225 (32 mm x 3/4")
    CFF 3232 (32 mm x 1")
        
    90° Threaded Elbow PN25 - Male
    CFM 2020 (20 mm x 1/2")
    CFM 2025 (20 mm x 3/4")
    CFM 2520 (25 mm x 1/2")
    CFM 2525 (25 mm x 3/4")
    CFM 3225 (32 mm x 3/4")
    CFM 3232 (32 mm x 1")
        
    90° Long Threaded Elbow PN25 - Female
    CFL 2020 (20 mm x 1/2")
    CFL 2520 (25 mm x 1/2")
       
    90° Threaded Elbow with Bracket PN25 - Female
    FFS 2020 (20mm x 1/2")
    FFS 2520 (25 mm x 1/2")
    
    90° Threaded Elbow with Bracket PN25 - Male
    FMS 2020 (20 mm x 1/2")
    FMS 2520 (25 mm x 1/2")
       
    90° Threaded Elbow PN25 - Female with Male
    CCF 2020 (20 mm x 1/2")
       
    90° Threaded Elbow PN25 - Male with Male
    CCM 2020 (20 mm x 1/2")
        
    Threaded Tee PN25 - Female
    TEF 2020 (20 mm x 1/2" x 20 mm)
    TEF 2025 (20 mm x 3/4" x 20 mm)
    TEF 2520 (25 mm x 1/2" x 25 mm)
    TEF 2525 (25 mm x 3/4" x 25 mm)
    TEF 3225 (32 mm x 3/4" x 32 mm)
    TEF 3232 (32 mm x 1" x 32 mm)
       
    Threaded Tee PN25 - Male
    TEM 2020 (20 mm x 1/2" x 20 mm)
    TEM 2025 (20 mm x 3/4" x 20 mm)
    TEM 2520 (25 mm x 1/2" x 25 mm)
    TEM 2525 (25 mm x 3/4" x 25 mm)
    TEM 3225 (32 mm x 3/4" x 32 mm)
    TEM 3232 (32 mm x 1" x 32 mm)
    
    Threaded Coupling PN25 - Female
    RFF 2020 (20 mm x 1/2")
    RFF 2025 (20 mm x 3/4")
    RFF 2520 (25 mm x 1/2")
    RFF 2525 (25 mm x 3/4")
    RFF 3225 (32 mm x 3/4")
    RFF 3232 (32 mm x 1")
    RFF 4040 (40 mm x 1-1/4")
    RFF 5050 (50 mm x 1-1/2")
    RFF 6363 (63 mm x 2")
    RFF 7575 (75 mm x 2-1/2")
    RFF 9090 (90 mm x 3")
    RFF 110110 (110 mm x 4")
    
    Threaded Coupling PN25 - Male
    RFM 2020 (20 mm x 1/2")
    RFM 2025 (20 mm x 3/4")
    RFM 2520 (25 mm x 1/2")
    RFM 2525 (25 mm x 3/4")
    
    Fixed Wall Assembly Group
    GVF 2020 (20 mm x 1/2")
    GVF 2520 (25 mm x 1/2")
        
    Brass Adapter PN25 - Female
    GGF 2020 (20 mm x 1/2")
    GGF 2525 (25 mm x 3/4")
    GGF 3232 (32 mm x 1")
    GGF 4040 (40 mm x 1-1/4")
    GGF 5050 (50 mm x 1-1/2")
    GGF 6363 (63 mm x 2")
       
    Brass Adapter PN25 - Male
    GGM 2020 (20 mm x 1/2")
    GGM 2525 (25 mm x 3/4")
    GGM 3232 (32 mm x 1")
    GGM 4040 (40 mm x 1-1/")
    GGM 5050 (50 mm x 1-1/2")
    GGM 6363 (63 mm x 2")
    RFM 3225 (32 mm x 3/4")
    RFM 3232 (32 mm x 1")
    RFM 4040 (40 mm x 1-1/4")
    RFM 5050 (50 mm x 1-1/2")
    RFM 6363 (63 mm x 2")
    RFM 7575 (75 mm x 2-1/2")
    RFM 9090 (90 mm x 3")
    RFM 110110 (110 mm x 4")
       
    Wall Assembly Group
    GVS 2020 (1/2" x 1/2")
        
    Wall Assembly Group with Template
    GVD 2020 (20 mm x 1/2")
    GVD 2520 (25 mm x 1/2")
[G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for
    “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state
    laws and the U.S. Safe Drinking Water Act.

    

Pipe[4] [G]
TORO 25 20 mm - 250 mm D. HOT PP

[4] Pipe models include:
    
    FIBER Pipe
    TUB 20 SDR6 F
    TUB 25 SDR6 F
    
    FIBER EVO Pipe
    TUB 32 SDR9 FE
    TUB 40 SDR9 FE
    TUB 50 SDR9 FE
    TUB 63 SDR9 FE
    TUB 75 SDR9 FE
    TUB 90 SDR9 FE
    TUB 110 SDR9 FE
    TUB 125 SDR9 FE
    TUB 160 SDR9 FE
    TUB 200 SDR9 FE
    TUB 250 SDR9 FE
    TUB 20 SDR7.4 FE
    TUB 25 SDR7.4 FE
    TUB 32 SDR7.4 FE
    TUB 40 SDR7.4 FE
    TUB 50 SDR7.4 FE
    TUB 63 SDR7.4 FE
    TUB 75 SDR7.4 FE
    TUB 90 SDR7.4 FE
    TUB 110 SDR7.4 FE
    TUB 125 SDR7.4 FE
    TUB 160 SDR7.4 FE
    TUB 200 SDR7.4 FE
    TUB 250 SDR7.4 FE
    TUB 32 SDR11 FE
    TUB 40 SDR11 FE
    TUB 50 SDR11 FE
    TUB 63 SDR11 FE
    TUB 75 SDR11 FE
    TUB 90 SDR11 FE
    TUB 110 SDR11 FE
    TUB 125 SDR11 FE
    TUB 160 SDR11 FE
    TUB 200 SDR11 FE
    TUB 250 SDR11 FE
    TUB 160 SDR17 FE
    TUB 200 SDR17 FE
    TUB 250 SDR17 FE
      
    PPR Pipe
    TUB X A10 - PN10 - SDR11/S5 (20 – 63 mm)
    TUB X A16 - PN16 - SDR7.4/S3.2 (20 – 63 mm)
    TUB X A20 - PN20 - SDR6/S2.5 (20 – 63 mm)
      
    EvO Pipe
    TUB X A10 E - PN10 - SDR17/S8 (75 – 250 mm)
    TUB X A16 E - PN16 - SDR11/S5 (75 – 250 mm)
    TUB X A20 E - PN20 - SDR7.4/S3.2 (75 – 160 mm)
    TUB X A20 E - PN20 - SDR9/S4 (200 – 250 mm)
    TUB X A25 E - PN25 - SDR6/S2.5 (20 – 160 mm)
      
    X corresponds to the size in mm.
[G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for
    “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state
    laws and the U.S. Safe Drinking Water Act.

    



 
A.U.K. Müller GmbH & Co. KG 
Dresdener Str. 162
D-40595 Düsseldorf 
Germany 
49 21 173 910
Visit this company's website


Facility : Düsseldorf, Germany

Mechanical Devices

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Solenoid Valves[G]
10.009.115 Solenoid 3/4" C. HOT MLTPL
10.009.126 Solenoid 3/4" C. HOT MLTPL
62.005.115 Solenoid 3/4" C. HOT MLTPL
62.005.126 Solenoid 3/4" C. HOT MLTPL
62.005.815 Solenoid 3/4" C. HOT MLTPL
62.005.826 Solenoid 3/4" C. HOT MLTPL
62.007.115 Solenoid 3/4" C. HOT MLTPL
62.007.126 Solenoid 3/4" C. HOT MLTPL
62.009.115 Solenoid 3/4" C. HOT MLTPL
62.009.126 Solenoid 3/4" C. HOT MLTPL

[G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for
    “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state
    laws and the U.S. Safe Drinking Water Act.

    

Valves[G]
52.009.100 3/4" C. HOT MLTPL
52.009.200 3/4" C. HOT MLTPL

[G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for
    “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state
    laws and the U.S. Safe Drinking Water Act.

    

NOTE: Only products bearing the NSF Mark on the product, product packaging, and/or
      documentation shipped with the product are Certified.

Mechanical Plumbing Devices

Trade Designation      

Faucet Cartridges[G] [Q]

T02 50.009.800
     

50.005.811
     

50.005.801
     

50.009.811
     

50.009.101
     

51.005.101 Cartridge Valve
     

T01 50.009.800
     

50.005.800
     

51.005.101 Cartridge Valve
     

50.007.801
     

50.007.811
     

50.009.801
     

[G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for
    “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state
    laws and the U.S. Safe Drinking Water Act.

    
[Q] This product meets the reduced Q test statistic criteria of 1 µg or 0.5 µg for lead per
    Section 9.5.1.1 of NSF/ANSI/CAN 61.

Solenoid Valves[G]

50.005.126 bistable 2/2-way solenoid valve[2]
     

[2] This product does not require a Q statistic. It is made from material or materials that
    do not require lead analysis when reviewed per NSF/ANSI/CAN Standard 61, Section 3.3.

50.005.102 Cartridge Valve[Q]
     

[Q] This product meets the reduced Q test statistic criteria of 1 µg or 0.5 µg for lead per
    Section 9.5.1.1 of NSF/ANSI/CAN 61.

[G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for
    “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state
    laws and the U.S. Safe Drinking Water Act.

    

Valves[G] [Q]
50.005.100 Cartridge Valve      
50.005.850      
50.007.101      
50.007.806 Solenoid Cartridge Valve[1]      
51.005.100      
51.005.125      

[1] Certified for models that include: 
    G 1/2 male threads 
    G 3/8 male threaded with G 3/8 female threads 
    G 3/8 male threaded with G 1/2 female threads 
    Model with sockets for customer provided fitting adapters.

[G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for
    “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state
    laws and the U.S. Safe Drinking Water Act.

    
[Q] This product meets the reduced Q test statistic criteria of 1 µg or 0.5 µg for lead per
    Section 9.5.1.1 of NSF/ANSI/CAN 61.

NOTE: Only products bearing the NSF Mark on the product, product packaging, and/or
      documentation shipped with the product are Certified.

Pipes and Related Products

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Fittings [G]
CF-13 2MFC[1] 3/4" x 3/4" x 3/4" D. HOT MLTPL
CF-13 2MFO[1] 1/2" x ¾" x ¾" x ¾" D. HOT MLTPL
CF-17 2MFC[1] 3/4" C. HOT MLTPL
CF-17 2MFO[1] 3/4" C. HOT MLTPL
CF-17 3MFC[1] 3/4" C. HOT MLTPL
CF-17 3MFO[1] 3/4" C. HOT MLTPL
CF-17 C (cross piece)[1] 3/4" C. HOT MLTPL
CF-17 L (L-piece)[1] 3/4" C. HOT MLTPL
CF-17 T (T-piece)[1] 3/4" C. HOT MLTPL
CF-H G Connector 3/4"x1/8"-3/4"x1/4" C. HOT MLTPL
CF-H L 90 deg Elbow Connector 3/4" x 1/2" C. HOT MLTPL
CF-H S Straight Connector 3/4"x3/8"-3/4"x1/2" C. HOT MLTPL

[1] MFC - are models with capped outlets
    MFO - are models without capped outlets
[G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for
    “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state
    laws and the U.S. Safe Drinking Water Act.

    

NOTE: Only products bearing the NSF Mark on the product, product packaging, and/or
      documentation shipped with the product are Certified.


 
A.W. Cook Cement Products, Inc. 
242 Amy Industrial Lane
Hoschton, GA 30548 
United States 
706-654-3677


Facility : Hoschton, GA

Protective (Barrier) Materials

    Water Water
  Water Contact Contact Contact
Trade Designation Size Restriction Temp Material

Coatings - Fittings[1]
Cemtec Silatec PW >= 6" CLD 23 CMNT

[1] Coating Notes:
    Color: Gray
    Number of Coats: 2 - 4
    Maximum Field Use Dry Thickness (in mils): 2000 mils
    Recoat Cure Time and Temperature: 1 hour at 75°F
    Final Cure Time/Temperature: 7 days @ 75°F
    Special Comments: Mix ratio is 4 quarts of water to one 60 lb bag of Cemtec Silatec PW. 
    Ensure proper surface preparation guidelines are followed prior to installation.

Coatings - Pipe[1]
Cemtec Silatec PW >= 48" CLD 23 CMNT

[1] Coating Notes:
    Color: Gray
    Number of Coats: 2 - 4
    Maximum Field Use Dry Thickness (in mils): 2000 mils
    Recoat Cure Time and Temperature: 1 hour at 75°F
    Final Cure Time/Temperature: 7 days @ 75°F
    Special Comments: Mix ratio is 4 quarts of water to one 60 lb bag of Cemtec Silatec PW. 
    Ensure proper surface preparation guidelines are followed prior to installation.

Coatings - Tank[1]
Cemtec Silatec PW >= 10,000 gal. CLD 23 CMNT

[1] Coating Notes:
    Color: Gray
    Number of Coats: 2 - 4
    Maximum Field Use Dry Thickness (in mils): 2000 mils
    Recoat Cure Time and Temperature: 1 hour at 75°F
    Final Cure Time/Temperature: 7 days @ 75°F
    Special Comments: Mix ratio is 4 quarts of water to one 60 lb bag of Cemtec Silatec PW. 
    Ensure proper surface preparation guidelines are followed prior to installation.



 
A.Y. McDonald Manufacturing 
4800 Chavenelle Road
Dubuque, IA 52001 
United States 
563-583-7311


Facility : Santa Fe Springs, CA

Pipes and Related Products

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Fittings
Copper Alloy Press-Connect Pressure Fittings 1/8" - 2 C. HOT BRASS

[1] Certified for the following configurations:
    90º Elbow Drop Ear PXF 1/2" x 3/8" - 1" x 1"
    90º Elbow Brass PXF 1/2" X 3/8" - 2" x 2"
    90º Elbow HI Ear PXF 1/2"
    Elbow Double Drop PXPXF 1/2" - 3/4"
    Union PxP 1/2" - 2"
    Union PxF 1/2" - 2"
    Union PxM 1/2" - 2"
    Vent Elbow PXPXF 1/2" x 1/2" x 1/8" - 3/4" x 3/4" x 1/8"
[G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for
    “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state
    laws and the U.S. Safe Drinking Water Act.

    


Facility : Kyunggi-Do, Republic of Korea

Pipes and Related Products

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Fittings[1] [G]
Copper Press-connect Pressure Fittings 1/2" - 4" C. HOT MLTPL

[1] Certified for the following configurations:
    90º Elbow PXP 1/2" - 4"
    90º Elbow FtgXP 1/2" - 4"
    Short Turn 90° Elbow PXP 1/2" - 4"
    Short Turn 90° Elbow FtgXP 1/2" - 4"
    45º Elbow PXP 1/2" - 4"
    45º Elbow FtgXP 1/2" - 4"
    Short Turn 45° Elbow PXP 1/2" - 4"
    Short Turn 45° Elbow FtgXP 1/2" - 4"
    Cap 1/2" - 4"
    Adapter PXF 1/2" - 4"
    Adapter PxM 1/2" - 4"
    Roll Stop Coupling PXP 1/2" - 4"
    No Stop Coupling PXP 1/2" - 4"
    With Stop Coupling 1/2" - 4"
    Reducing Coupling PXP 3/4" x 1/2" - 4" x 3"
    Reducing Coupling FtgXP 3/4" x 1/2" - 4" x 3"
    Tee PXPXP 1/2" - 4"
    Crossover PXP 1/2" - 3/4"
    Crossover FtgXP 1/2" - 3/4"
    Extended Coupling PXP 1/2" - 2"
    Adapter Ftg x F 1/2" - 2"
    Adapter Ftg x M 1/2" - 2"
    90° ELBOW P x F 1/2" - 2"
    90° ELBOW P x M 1/2" - 2"
    90° EXTENDED STREET ELBOW P x Ftg 3/4"
    TEE P x P x F 1/2" - 4"
    Adapter Flange P x Flange (4BOLT) 1/2" - 4"
    Adapter Flange P x Flange (8BOLT) 2 1/2" - 4"
    MANIFOLDS P x P 1" x 1/2" - 1" x 3/4"
[G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for
    “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state
    laws and the U.S. Safe Drinking Water Act.

    



 
AAG - All American Gasket 
291 Howard St.
Brockton, MA 02302 
United States 
508-588-7500


Facility : Brockton, MA

Joining and Sealing Materials

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Gasket/Sealing Materials[1] [G]
EP61 [2] C. HOT EPDM

[1] This product has also been evaluated for use in Mechanical Plumbing Device applications
    with a maximum use restriction of 0.2 square inches/L.
[2] Certified for a maximum surface area to volume ratio of 2.0 square inches/L.
[G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for
    “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state
    laws and the U.S. Safe Drinking Water Act.

    

O-Rings[1] [G]
EP61 [2] C. HOT EPDM

[1] This product has also been evaluated for use in Mechanical Plumbing Device applications
    with a maximum use restriction of 0.2 square inches/L.
[2] Certified for a maximum surface area to volume ratio of 2.0 square inches/L.
[G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for
    “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state
    laws and the U.S. Safe Drinking Water Act.

    



 
Aalberts Integrated Piping Systems Americas, Inc. DBA Conbraco Industries, Inc. 
1418 South Pearl Street
Pageland, SC 29728 
United States 
704-841-6000


Facility : # 1 China

Mechanical Devices

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Valves[1] [2] [G]
215L YY SSP8TAX 2" - 48" CLD 23 MLTPL
215LYYBBB8TAX 2" - 48" CLD 23 MLTPL
215LYYJJJ8TAX 2" - 48" CLD 23 MLTPL
215LYYKKK8TAX 2" - 48" CLD 23 MLTPL
215LYYSSS8TAX 2" - 48" CLD 23 MLTPL
215W YY SSP8TAX 2" - 48" CLD 23 MLTPL
215WYYBBB8TAX 2" - 48" CLD 23 MLTPL
215WYYJJJ8TAX 2" - 48" CLD 23 MLTPL
215WYYKKK8TAX 2" - 48" CLD 23 MLTPL
215WYYSSS8TAX 2" - 48" CLD 23 MLTPL
230L YY SSP8TAX 2" - 48" CLD 23 MLTPL
230LYYBBB8TAX 2" - 48" CLD 23 MLTPL
230LYYJJJ8TAX 2" - 48" CLD 23 MLTPL
230LYYKKK8TAX 2" - 48" CLD 23 MLTPL
230LYYSSS8TAX 2" - 48" CLD 23 MLTPL
230W YY SSP8TAX 2" - 48" CLD 23 MLTPL
230WYYBBB8TAX 2" - 48" CLD 23 MLTPL
230WYYJJJ8TAX 2" - 48" CLD 23 MLTPL
230WYYKKK8TAX 2" - 48" CLD 23 MLTPL
230WYYSSS8TAX 2" - 48" CLD 23 MLTPL

[1] Certified for equivalent metric sizes.
[2] YY - 02 through 48
[G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for
    “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state
    laws and the U.S. Safe Drinking Water Act.

    



 
ABB Ltd. 
Oldends Lane
Stonehouse, Glos 
GL10 3TA 
United Kingdom 
44 14 5382 6661


Facility : Warminster, PA

Mechanical Devices

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Water Meters[1] [G]
AquaMaster FEF >= 250 mm CLD 23 MLTPL
AquaMaster FER 40 mm - 600 mm CLD 23 MLTPL
AquaMaster FEW 40 mm - 2400 mm CLD 23 MLTPL
FEW XYZ.F 40 mm - 2400 mm CLD 23 MLTPL
FEW XYZ.R 40 mm - 600 mm CLD 23 MLTPL
ProcessMaster FEW XYZ 40 mm - 2400 mm CLD 23 MLTPL
WaterMaster FEF >= 250 mm CLD 23 MLTPL
WaterMaster FER 40 mm - 600 mm CLD 23 MLTPL
WaterMaster FEW 40 mm - 2400 mm CLD 23 MLTPL

[1] For all meters:
    X - Type of electronics
        4 - AquaMaster
        5 - WaterMaster
        6 - ProcessMaster
    Y - Tier of Electronics
        1 - Standard Electronics
        2 - Enhanced Electronic
        3 - Advanced Electronics
        5 - Premium Electronics
    Z - Type of mounting
        1 - Integral with transmitter
        2 - Remote with transmitter (Sensor + Transmitter)
        8 - Sensor only
    Type of bore and liner
    F - FEF/Full bore/Rubber liner
    R - FER/Reduced bore/Rubber liner
    
[G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for
    “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state
    laws and the U.S. Safe Drinking Water Act.

    

NOTE: Only products bearing the NSF Mark on the product, product packaging, and/or
      documentation shipped with the product are Certified.


Facility : Shanghai, China

Mechanical Devices

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Water Meters[1] [G]
Aquamaster FEW 40 mm - 2400 mm CLD 23 MLTPL
FEW XYZ.F 40 mm - 2400 mm CLD 23 MLTPL
ProcessMaster FEW XYZ 40 mm - 2400 mm CLD 23 MLTPL
WaterMaster FEW 40 mm - 2400 mm CLD 23 MLTPL

[1] For all meters:
    X - Type of electronics	
        4 - AquaMaster	
        5 - WaterMaster
        6 - ProcessMaster		
    Y - Tier of Electronics	
        1 - Standard Electronics
        2 - Enhanced Electronic
        3 - Advanced Electronics	
        5 - Premium Electronics	
    Z - Type of mounting	
        1 - Integral with transmitter
        2 - Remote with transmitter (Sensor + Transmitter)
        8 - Sensor only	
    Type of bore and liner	
        F - FEF/Full bore/Rubber liner
[G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for
    “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state
    laws and the U.S. Safe Drinking Water Act.

    

NOTE: Only products bearing the NSF Mark on the product, product packaging, and/or
      documentation shipped with the product are Certified.


Facility : Glos, United Kingdom

Mechanical Devices

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Switches/Sensors
FEA121 - AquaProbe (with WaterMaster transmitter) 1" - 1.5" D. HOT MLTPL
FEA181 - AquaProbe (probe only) 1" - 1.5" D. HOT MLTPL
FEA221 - AquaProbe (with AquaMaster3 transmitter) 1" - 1.5" D. HOT MLTPL
FEA281 - AquaProbe (Flow sensor only) 1" - 1.5" D. HOT MLTPL
FEW xyz.A[1] 1" - 1.5" D. HOT MLTPL

[1] FEW XYZ A
    X - Type of electronics
        4 - AquaMaster
        5 - WaterMaster
    Y - Tier of Electronics
        1 - Standard Electronics
        3 - Advanced Electronics
        5 - Premium Electronics
    Z - Type of mounting
        1 - Integral
        2 - Remote

Water Meters [G]
AquaMaster FEF[2] >= 250 mm CLD 23 MLTPL
AquaMaster FER[2] 40 mm - 600 mm CLD 23 MLTPL
AquaMaster FEV[3] 40 mm - 200 mm CLD 23 MLTPL
AquaMaster FEW[2] 40 mm - 2400 mm CLD 23 MLTPL
FEW XYZ.F[2] 40 mm - 2400 mm CLD 23 MLTPL
FEW XYZ.R[2] 40 mm - 600 mm CLD 23 MLTPL
FEW XYZ.V[3] 40 mm - 200 mm CLD 23 MLTPL
ProcessMaster FEW XYZ[2] 40 mm - 2400 mm CLD 23 MLTPL
WaterMaster FEF[2] >= 250 mm CLD 23 MLTPL
WaterMaster FER[2] 40 mm - 600 mm CLD 23 MLTPL
WaterMaster FEV[3] 40 mm - 200 mm CLD 23 MLTPL
WaterMaster FEW[2] 40 mm - 2400 mm CLD 23 MLTPL

[2] For all meters:
    X - Type of electronics
        4 - AquaMaster
        5 - WaterMaster
        6 - ProcessMaster
    Y - Tier of Electronics
        1 - Standard Electronics
        2 - Enhanced Electronic
        3 - Advanced Electronics
        5 - Premium Electronics
    Z - Type of mounting
        1 - Integral with transmitter
        2 - Remote with transmitter (Sensor + Transmitter)
        8 - Sensor only
    Type of bore and liner:
    F - FEF/Full bore/Rubber liner
    R - FER/Reduced bore/Rubber liner
    
[3] For all meters:
    X - Type of electronics
    	4 - AquaMaster
    	5 - WaterMaster
    Y - Tier of Electronics
    	1 - Standard Electronics
    	3 - Advanced Electronics
    	5 - Premium Electronics
    Z - Type of mounting
    	1 - Integral with transmitter
        2 - Remote with transmitter (Sensor + Transmitter)
        8 - Sensor only
    Type of bore and liner:
    V – FEV/Optimized bore/PP liner
[G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for
    “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state
    laws and the U.S. Safe Drinking Water Act.

    

NOTE: Only products bearing the NSF Mark on the product, product packaging, and/or
      documentation shipped with the product are Certified.


 
ABB S.p.A. 
Via Luigi Vaccani, 4
22016 Ossuccio, Como 
Italy 
39 03 445 8111
Visit this company's website


Facility : Warminster, PA

Mechanical Devices

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Transmitters/Gauges[G]
261AS ABSOLUTE PRESS XMTR 60 x 60 x 112 mm C. HOT MLTPL
261GS GAUGE PRESS XMTR 60 x 60 x 112 mm C. HOT MLTPL
266DSH Differential Pressure Transmitter 142 x 142 x 210 mm C. HOT MLTPL
266HSH Gauge Pressure Transmitter 142 x 91 x 215 mm C. HOT MLTPL
266NSH Absolute Pressure Transmitter 142 x 91 x 215 mm C. HOT MLTPL

[G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for
    “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state
    laws and the U.S. Safe Drinking Water Act.

    

NOTE: Only products bearing the NSF Mark on the product, product packaging, and/or
      documentation shipped with the product are Certified.


 
Abbott Rubber Company, Inc. 
1311 Meachum Rd.
Itasca, IL 60143 
United States 
800-852-1855 
847-952-1800
Visit this company's website


Facility : # 1 Canada

Pipes and Related Products

    Water Water
    Contact Contact
Trade Designation Size Temp Material

PVC Hose[1] [G]
T12 Series 1/8" - 2" CLD 23 FPVC

[1] This product has been evaluated for use in Piping (Section 4) applications: 
    			
    Diameter:	Length:			
    1/8" - 5/16"	No Restriction			
    3/8"    270"			
    7/16"   230"			
    1/2"    200"			
    9/16"   180"			
    5/8"    160" 			
    11/16"  145" 			
    3/4"    135" 			
    13/16" - 2" 	No Restriction
[G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for
    “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state
    laws and the U.S. Safe Drinking Water Act.

    

PVC Tubing[1] [G]
T10 Series 1/8" - 2" CLD 23 FPVC

[1] This product has been evaluated for use in Piping (Section 4) applications: 
    			
    Diameter:	Length:			
    1/8" - 5/16"	No Restriction			
    3/8"    270"			
    7/16"   230"			
    1/2"    200"			
    9/16"   180"			
    5/8"    160" 			
    11/16"  145" 			
    3/4"    135" 			
    13/16" - 2" 	No Restriction
[G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for
    “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state
    laws and the U.S. Safe Drinking Water Act.

    



 
ABN Pipe Systems S.L.U. 
Estrada Baños de Arteixo, 28
A Coruña 15008 
Spain 
34 650 720 82
Visit this company's website


Facility : Medina del Campo, Valladolid, Spain

Pipes and Related Products

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Fittings[1] [G]
ABN//INSTAL FITTING RD 16 mm - 400 mm C. HOT PP

[1] Configurations (mm) include:
    Reducing Tee (Unequal Tee)
    20-16-20 D1TR020016020
    25-20-20 D1TR025020020
    25-20-25 D1TR025020025
    32-25-25 D1TR032020032
    32-20-32 D1TR032025025
    32-25-32 D1TR032025032
    40-20-40 D1TR040020040
    40-25-40 D1TR040025040
    40-32-40 D1TR040032040
    50-25-50 D1TR050025050
    50-32-50 D1TR050032050
    50-40-50 D1TR050040050
    63-25-63 D1TR063025063
    63-32-63 D1TR063032063
    63-40-63 D1TR063040063
    63-50-63 D1TR063050063
    75-32-75 D1TR075032075
    75-40-75 D1TR075040075
    75-50-75 D1TR075050075
    75-63-75 D1TR075063075
    90-50-90 D1TR090050090
    90-63-90 D1TR090063090
    90-75-90 D1TR090075090
    110-63-110 D1TR110063110
    110-75-110 D1TR110075110
    110-90-110 D1TR110090110
    45° Elbow
    16 D1C0160450000
    20 D1C0200450000
    25 D1C0250450000
    32 D1C0320450000
    40 D1C0400450000
    50 D1C0500450000
    63 D1C0630450000
    75 D1C0750450000
    90 D1C0900450000
    110 D1C1100450000
    125 D1C1250450000
    160 D1C1600450000
    90° Elbow
    16 D1C0160900000
    20 D1C0200900000
    25 D1C0250900000
    32 D1C0320900000
    40 D1C0400900000
    50 D1C0500900000
    63 D1C0630900000
    75 D1C0750900000
    90 D1C0900900000
    110 D1C1100900000
    125 D1C1250900000
    160 D1C1600900000
    Socket
    16 D1M0160000000
    20 D1M0200000000
    25 D1M0250000000
    32 D1M0320000000
    40 D1M0400000000
    50 D1M0500000000
    63 D1M0630000000
    75 D1M0750000000
    90 D1M0900000000
    110 D1M1100000000
    125 D1M1250000000
    160 D1M1600000000
    Equal Tee
    16 D1T0160000000
    20 D1T0200000000
    25 D1T0250000000
    32 D1T0320000000
    40 D1T0400000000
    50 D1T0500000000
    63 D1T0630000000
    75 D1T0750000000
    90 D1T0900000000
    110 D1T1100000000
    125 D1T1250000000
    160 D1T1600000000
    End Cap
    16 D1TA016000000
    20 D1TA020000000
    25 D1TA025000000
    32 D1TA032000000
    40 D1TA040000000
    50 D1TA050000000
    63 D1TA063000000
    75 D1TA075000000
    90 D1TA090000000
    110 D1TA110000000
    125 D1TA125000000
    160 D1TA160000000
    Flange Adaptor
    40 D1P0400000000
    50 D1P0500000000
    63 D1P0630000000
    75 D1P0750000000
    90 D1P0900000000
    110 D1P1100000000
    125 D1P1250000000
    160 D1P1600000000
    Reducer
    20-16 D1R0200160000
    25-20 D1R0250200000
    32-20 D1R0320200000
    32-25 D1R0320250000
    40-25 D1R0400250000
    40-32 D1R0400320000
    50-32 D1R0500320000
    50-40 D1R0500400000
    63-25 D1R0630250000
    63-32 D1R0630320000
    63-40 D1R0630400000
    63-50 D1R0630500000
    75-40 D1R0750400000
    75-50 D1R0750500000
    75-63 D1R0750630000
    90-63 D1R0900630000
    90-75 D1R0900750000
    110-63 D1R1100630000
    110-75 D1R1100750000
    110-90 D1R1100900000
    125-110 D1R1251100000
    160-110 D1R1601100000
    160-125 D1R1601250000
    Cross
    32 D1CRU03200000
    40 D1CRU04000000
    Reducing Cross
    50-32 D1CRUR0500320
    63-32 D1CRUR0630320
    63-40 D1CRUR0630400
    75-32 D1CRUR0750320
    75-40 D1CRUR0750400
    75-50 D1CRUR0750500
    90-50 D1CRUR0900500
    End Cap SDR11
    160 D5TAIS5160000
    200 D5TAIS5200000
    250 D5TAIS5250000
    315 D5TAIS5315000
    End Cap SDR17
    160 D5TAIS8160000
    200 D5TAIS8200000
    250 D5TAIS8250000
    315 D5TAIS8315000
    Flange Adaptor SDR11
    160 D5PIS51600000
    200 D5PIS52000000
    250 D5PIS52500000
    315 D5PIS53150000
    400 D5PIS54000000
    Flange Adaptor SDR17
    160 D5PIS81600000
    200 D5PIS82000000
    250 D5PIS82500000
    315 D5PIS83150000
    400 D5PIS84000000
    Cross over fittings
    20 D1S0200200000
    25 D1S0250200000
    32 D1S0320200000
[G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for
    “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state
    laws and the U.S. Safe Drinking Water Act.

    

Fittings, Non-Repeating[2] [G]
ABN//INSTAL FITTING RD 16 mm - 110 mm C. HOT PP

[2] Configurations (mm) include:
    Backplate 90° Elbow
    16-1/2" D2CP016012000
    20-1/2" D2CP020012000
    25-1/2" D2CP025012000
    Female Threaded Tee
    16-1/2" D2TRH01601200
    20-1/2" D2TRH02001200
    25-1/2" D2TRH02501200
    25-3/4" D2TRH02503400
    32-1/2" D2TRH03201200
    32-3/4" D2TRH03203400
    32-1" D2TRH03200100
    50-1/2" D2TRH05012000
    63-1/2" D2TRH06312000
    Female Hex. Threaded Adaptor
    32-1" D2ERHTE032001
    40-1 1/4" D2ERHTE040114
    50-1 1/2" D2ERHTE050112
    63-2" D2ERHTE063002
    75-2 1/2" D2ERHTE075212
    90-3" D2ERHTE090003
    110-4" D2ERHTE110004
    Male Hex. Threaded Adaptor
    32-1" D2ERMTE032001
    40-1 1/4" D2ERMTE040114
    50-1 1/2" D2ERMTE050112
    63-2" D2ERMTE063002
    75-2 1/2" D2ERMTE075212
    90-3" D2ERMTE090003
    110-4" D2ERMTE110004
    90° Elbow Female Threaded
    16-1/2" D2CRH01601290
    20-1/2" D2CRH02001290
    25-1/2" D2CRH02501290
    25-3/4" D2CRH02503490
    32-3/4" D2CRH03203490
    32-1" D2CRH03200190
    90° Elbow Male Threaded
    20-1/2" D2CRM02001290
    20-3/4" D2CRM02003490
    25-1/2" D2CRM02501290
    25-3/4" D2CRM02503490
    32-3/4" D2CRM03203490
    32-1" D2CRM03200190
    Adaptor Female Threaded
    16-1/2" D2ERH01601200
    20-1/2" D2ERH02001200
    25-1/2" D2ERH02501200
    25-3/4" D2ERH02503400
    32-3/4" D2ERH03203400
    Adaptor Male Threaded
    16-1/2" D2ERM01601200
    20-1/2" D2ERM02001200
    20-3/4" D2ERM02003400
    25-1/2" D2ERM02501200
    25-3/4" D2ERM02503400
    32-3/4" D2ERM03203400
    Adaptor Union Female Threaded
    20-1/2" D2TURH0200120
    25-3/4" D2TURH0250340
    32-1" D2TURH0320001
    40-1 1/4" D2TURH0401140
    50-1 1/2" D2TURH0501120
    63-2" D2TURH0630200
    75-2 1/2" D2TURH0750212
    90-3" D2TURH0900003
    110-4" D2TURH1100004
    Adaptor Union Male Threaded
    20-1/2" D2TURM0200120
    25-3/4" D2TURM0250340
    32-1" D2TURM0320001
    40-1 1/4" D2TURM0401140
    50-1 1/2" D2TURM0501120
    63-2" D2TURM0630002
    75-2 1/2" D2TURM0750212
    90-3" D2TURM0900003
    110-4" D2TURM1100004
[G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for
    “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state
    laws and the U.S. Safe Drinking Water Act.

    

Pipe[G]
ABN//INSTAL CT FASER RD 20 mm - 500 mm C. HOT PP

[G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for
    “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state
    laws and the U.S. Safe Drinking Water Act.

    

Service Saddles[3] [G]
ABN//INSTAL FITTING RD 20 x 50-63 x 315 mm C. HOT PP

[3] Welding Saddles - Male (saddle connection x pipe size)
    20-50 D5IDM02005000
    20-63 D5IDM02006300
    20-75 D5IDM02007500
    20-90 D5IDM02009000
    20-110 D5IDM02011000
    20-125 D5IDM02012500
    20-160 D5IDM02016000
    20-200 D5IDM02020000
    25-50 D5IDM02505000
    25-63 D5IDM02506300
    25-75 D5IDM02507500
    25-90 D5IDM02509000
    25-110 D5IDM02511000
    25-125 D5IDM02512500
    25-160 D5IDM02516000
    25-200 D5IDM02520000
    32-50 D5IDM03205000
    32-63 D5IDM03206300
    32-75 D5IDM03207500
    32-90 D5IDM03209000
    32-110 D5IDM03211000
    32-125 D5IDM03212500
    32-160 D5IDM03216000
    32-200 D5IDM03220000
    40-90 D5IDM04009000
    40-110 D5IDM04011000
    40-125 D5IDM04012500
    40-160 D5IDM04016000
    40-200 D5IDM04020000
    40-250 D5IDM04025000
    40-315 D5IDM04031500
    50-90 D5IDM05009000
    50-110 D5IDM05011000
    50-125 D5IDM05012500
    50-160 D5IDM05016000
    50-200 D5IDM05020000
    50-250 D5IDM05025000
    50-135 D5IDM05031500
    63-125 D5IDM06312500
    63-160 D5IDM06316000
    63-200 D5IDM06320000
    63-250 D5IDM06325000
    63-315 D5IDM06331500
    
    Welding Saddles - Female (saddle connection x pipe size)
    20-50 D5IDH02005000
    20-63 D5IDH02006300
    20-75 D5IDH02007500
    20-90 D5IDH02009000
    20-110 D5IDH02011000
    20-125 D5IDH02012500
    20-160 D5IDH02016000
    20-200 D5IDH02020000
    25-50 D5IDH02505000
    25-63 D5IDH02506300
    25-75 D5IDH02507500
    25-90 D5IDH02509000
    25-110 D5IDH02511000
    25-125 D5IDH02512500
    25-160 D5IDH02516000
    25-200 D5IDH02520000
    32-90 D5IDH03209000
    32-110 D5IDH03211000
    32-125 D5IDH03212500
    32-160 D5IDH03216000
    32-200 D5IDH03220000
    40-90 D5IDH04009000
    40-110 D5IDH04011000
    40-125 D5IDH04012500
    40-160 D5IDH04016000
    40-200 D5IDH04020000
    40-250 D5IDH04025000
    40-315 D5IDH04031500
    50-110 D5IDH05011000
    50-125 D5IDH05012500
    50-160 D5IDH05016000
    50-200 D5IDH05020000
    50-250 D5IDH05025000
    50-315 D5IDH05031500
    50-160 D5IDM05016000
    50-200 D5IDM05020000
    50-250 D5IDM05025000
    50-315 D5IDM05031500
    63-110 D5IDM06311000
    63-125 D5IDM06312500
    63-160 D5IDM06316000
    63-200 D5IDM06320000
    63-250 D5IDM06325000
    63-315 D5IDM06331500
[G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for
    “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state
    laws and the U.S. Safe Drinking Water Act.

    

NOTE: Only products bearing the NSF Mark on the product, product packaging, and/or
      documentation shipped with the product are Certified.


 
Accella Polyurethane Systems, LLC DBA Carlisle Polyurethane Systems, 
Carlisle Roof Foam and Coatings
2500 Adie Road 
Maryland Heights, MO 63043 
United States 
770-528-9556
Visit this company's website


Facility : Rancho Cucamonga, CA

Joining and Sealing Materials

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Grouts[1]
Substratum [2] CLD 23 PUR
Substratum 2F [2] CLD 23 PUR
Substratum 2R [2] CLD 23 PUR
Substratum 3F [2] CLD 23 PUR
Substratum 3R [2] CLD 23 PUR
Substratum 4F [2] CLD 23 PUR
Substratum 4R [2] CLD 23 PUR
Substratum 4S [2] CLD 23 PUR
Substratum 5R [2] CLD 23 PUR
Substratum 6R [2] CLD 23 PUR
Substratum Geopolymer [2] CLD 23 PUR

[1] Certified for product with the following densities and reaction speeds:
    2 pounds per cubic foot (regular speed)
    2 pounds per cubic foot (fast speed)
    3 pounds per cubic foot (regular speed)
    3 pounds per cubic foot (fast speed)
    4 pounds per cubic foot (slow speed)
    4 pounds per cubic foot (regular speed)
    4 pounds per cubic foot (fast speed)
    5 pounds per cubic foot (regular speed)
    6 pounds per cubic foot (regular speed)
    
    Mix ratio is 1:1 (A:B) by volume or 8.1:6.9 (A:B) by weight.
    Minimum cure time is 60 minutes at ambient temperatures.
[2] Certified for a maximum surface area to volume ratio of 0.375 square inches per liter.



Facility : Chattanooga, TN

Joining and Sealing Materials

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Grouts[1]
Substratum [2] CLD 23 PUR
Substratum 2F [2] CLD 23 PUR
Substratum 2R [2] CLD 23 PUR
Substratum 3F [2] CLD 23 PUR
Substratum 3R [2] CLD 23 PUR
Substratum 4F [2] CLD 23 PUR
Substratum 4R [2] CLD 23 PUR
Substratum 4S [2] CLD 23 PUR
Substratum 5R [2] CLD 23 PUR
Substratum 6R [2] CLD 23 PUR
Substratum Geopolymer [2] CLD 23 PUR

[1] Certified for product with the following densities and reaction speeds:
    2 pounds per cubic foot (regular speed)
    2 pounds per cubic foot (fast speed)
    3 pounds per cubic foot (regular speed)
    3 pounds per cubic foot (fast speed)
    4 pounds per cubic foot (slow speed)
    4 pounds per cubic foot (regular speed)
    4 pounds per cubic foot (fast speed)
    5 pounds per cubic foot (regular speed)
    6 pounds per cubic foot (regular speed)
    
    Mix ratio is 1:1 (A:B) by volume or 8.1:6.9 (A:B) by weight.
    Minimum cure time is 60 minutes at ambient temperatures.
[2] Certified for a maximum surface area to volume ratio of 0.375 square inches per liter.



 
Accent Control Systems 
2101 Potshop Lane
Norristown, PA 19403 
United States 
610-630-7640


Facility : Ningbo, China

Mechanical Devices

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Water Meters[G]
GLF-062/GLF-062-R 5/8" x 1/2" CLD 23 MLTPL
GLF-075/GLF-075-R 5/8" x 3/4" CLD 23 MLTPL
GLF-100/GLF-100-R 3/4" x 1" CLD 23 MLTPL
GLF-100F/GLF-100F-R 1" CLD 23 MLTPL
GLF-150/GLF-150-R 1 1/2" CLD 23 MLTPL
GLF-200(F)/GLF-200-R(F) 2" CLD 23 MLTPL
GLF-200/GLF-200-R 2" CLD 23 MLTPL

[G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for
    “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state
    laws and the U.S. Safe Drinking Water Act.

    



 
ACCESS TRUCK PARTS 
2757 E Chambers Street
Phoenix, AZ 85040 
United States 
602-437-6948


Facility : Anhui, China

Mechanical Devices

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Pumps [G]
101-XANN-YYG[1] 50x32 - 350x300 mm D. HOT MLTPL

[1] The variables in the trade name denote the following:
    "NN" refers to outlet size, ranging from 32 mm to 300 mm.
    "YY" refers to impeller diameter, ranging from 13 cm - 50 cm.
    "G" is an optional designation indicating High Speed.
[G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for
    “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state
    laws and the U.S. Safe Drinking Water Act.

    



 
Access-Able Technologies, Inc. 
1275 Bennett Drive #115
Longwood, FL 32750 
United States 
800-572-4894 
407-834-2999


Facility : # 1 USA

Joining and Sealing Materials

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Patching Materials [G]
Pow-R Stick Steel Hard Epoxy Putty (Copper Color) [1] [2] C. HOT EPOXY
Pow-R Stick Steel Hard Epoxy Putty (Grey Color) [1] [2] C. HOT EPOXY
Pow-R Stick Steel Hard Epoxy Putty (White Color) [1] [2] C. HOT EPOXY
STIC-O-STEEL POW-R Putty [1] [2] C. HOT EPOXY

[1] Certified for a maximum surface area to volume ratio of 0.3 sq. in./L in pipe or 1% of a
    20,000 gallon tank.
[2] To obtain the proper mix, use at least a 3/4" length, but no more than 1/3 of a full
    stick, of product which has been cut with a knife. Product must be mixed for 60-90
    seconds.
[G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for
    “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state
    laws and the U.S. Safe Drinking Water Act.

    



 
Accor Technology Inc. 
3310 South East 5th Street
East Wenatchee, WA 98802 
United States 
800-447-5848 
509-662-0608


Facility : East Wenatchee, WA

Mechanical Plumbing Devices

Trade Designation      

Connector Hoses

Riser Assemblies[1]
R-5CP(1)-7(2)      
R-5CS(1)-7(2)      
R-5LP(1)-5(2)      
R-5LS(1)-5(2)      
R-CP(1)-7(2)      
R-CS(1)-7(2)      
R-LP(1)-3(2)      
R-LP(1)-5(2)      
R-LS(1)-3(2)      
R-LS(1)-5(2)      
R2-IP(1)-2(2)      
R3-LP(1)-3(2)      
RCP45T12-7(2)      

[1] (1) Hose length
    (2) Packaging options (M, F, E, EL, CF, CM, PF, FM, XM, XF, XE, XL, XC, or R)

Supply Stops

Coupling w/ attached riser[1] [G]
PR30-LP(1)-3(2)      
PR30-SP(1)-3(2)      
PR50-CP(1)-7(2)      
PR50-CS(1)-7(2)      
PR50-LP(1)-3(2)      
PR50-LP(1)-5(2)      
PR50-LS(1)-3(2)      
PR50-LS(1)-5(2)      
PR50-P(1)-RK(2)      
PR50-S(1)-RK(2)      
PR50-SP(1)-5(2)      

[1] (1) Hose length
    (2) Packaging options (M, F, E, EL, CF, CM, PF, FM, XM, XF, XE, XL, XC, or R)
[G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for
    “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state
    laws and the U.S. Safe Drinking Water Act.

    

Valve or Coupling[1] [G]
PC5-3(2)      
PC5S-3(2)      
PE5-3(2)      
PE5S-3(2)      
PO5-2(2)      
PO5-3(2)      
PO5-75(2)      
PO5-CAP(2)      
PR-30(2)      
PR-50(2)      
TH5-3(2)      

[1] (1) Hose length
    (2) Packaging options (M, F, E, EL, CF, CM, PF, FM, XM, XF, XE, XL, XC, or R)
[G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for
    “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state
    laws and the U.S. Safe Drinking Water Act.

    

Valve w/ attached riser[1] [G]
PC5-CP(1)-7(2)      
PC5-CS(1)-7(2)      
PC5-LP(1)-5(2)      
PC5-LS(1)-5(2)      
PE5-CP(1)-7(2)      
PE5-CS(1)-7(2)      
PE5-LP(1)-5(2)      
PE5-LS(1)-5(2)      
PO5-CP(1)-7(2)      
PO5-CS(1)-7(2)      
PO5-IP(1)-2(2)      
PO5-LP(1)-3(2)      
PO5-LP(1)-5(2)      
PO5-LP4T15-5(2)      
PO5-LS(1)-3(2)      
PO5-LS(1)-5(2)      
PO5-LS4T15-5(2)      
PO5-P(1)-RK(2)      
PO5-P-PR30(2)      
PO5-S(1)-RK(2)      
PO5-S-PR30(2)      
PO5P10T10RK(2)      

[1] (1) Hose length
    (2) Packaging options (M, F, E, EL, CF, CM, PF, FM, XM, XF, XE, XL, XC, or R)
[G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for
    “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state
    laws and the U.S. Safe Drinking Water Act.

    



 
ACCOR Technology, Inc. 
3310 5th Street Southeast
East Wenatchee, WA 98802 
United States 
509-888-2233
Visit this company's website


Facility : East Wenatchee, WA

Mechanical Devices

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Miscellaneous Process Devices/Components[G]
PushOn 113A Accor Arrester 1/2" C. HOT MLTPL
PushOn 109A Accor Arrester 1/2" C. HOT MLTPL

[G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for
    “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state
    laws and the U.S. Safe Drinking Water Act.

    


Pipes and Related Products

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Fittings [G]
PF50C XE[1] 1/2" C. HOT MLTPL
PF50E XE[1] 1/2" C. HOT MLTPL
PF50MT XE[2] 1/2" C. HOT MLTPL
PF50T XE[1] 1/2" C. HOT MLTPL
PF75C XE[1] 3/4" C. HOT MLTPL
PF75E XE[1] 3/4" C. HOT MLTPL
PF75T XE[1] 3/4" C. HOT MLTPL

[1] Configuration code breakdown: 
    P  – PushOn 
    F  – Fitting 
    50 - 1/2" 
    75 - 3/4" 
    M  – Manifold 
    T  – Tee 
    C  – Coupling 
    E  – Elbow 
    X  – Compatible with PEX pipe (as well as copper and CPVC) 
    E  – Bulk packaged (each)
[2] PF50MT XE – 1/2" PushOnManifold Tee Code: 
    P  – PushOn 
    F  – Fitting 
    50 – 1/2 inch 
    M  – Manifold 
    T  – Tee 
    X  – Compatible with PEX pipe (as well as copper and CPVC). 
    E  – Bulk packaged (each)
[G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for
    “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state
    laws and the U.S. Safe Drinking Water Act.

    



 
ACCUCAST Ltd. 
415 South 21ST Street
Waco, TX 76706 
United States 
254-756-3200
Visit this company's website


Facility : Shanxi, China

Pipes and Related Products

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Fittings[1] [G]
Ductile Iron C110 Flanged Pipe Fittings 3" - 12" CLD 23 ASPH
Ductile Iron C153 Mechanical Joint Pipe Fittings 3" - 12" CLD 23 ASPH

[1] Certification does not include gaskets.
[G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for
    “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state
    laws and the U.S. Safe Drinking Water Act.

    



 
Accuflex Industrial Hose Ltd. 
760 Imperial Road North
Guelph, ON N1K 1Z3 
Canada 
519-836-5460
Visit this company's website


Facility : Guelph, Ontario, Canada

Pipes and Related Products

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Tubing/Hose[1] [G]
Bev-Flex® 172 1/4" - 1" CLD 23 PE
Bev-Seal® 176 1/4" - 1" CLD 23 PE
Bev-Seal® 228 1/4" - 1" CLD 23 PE
Bev-Seal® Ultra 175 3/16" - 1" CLD 23 PET
Bev-Seal® Ultra 235 3/16" - 1" CLD 23 PET
Bevlex® 170[2] 1/4" - 1" CLD 23 PE
Bevlex® 174 1/4" - 1" CLD 23 PE
Bevlex® 222 1/4" - 1" CLD 23 PE
Bevlex® 222YYY[3] 1/4" - 1" CLD 23 PE
Bevlex® 224 1/4" - 1" CLD 23 PE
Bevlex® Plus 180 3/16" - 1" CLD 23 PET
Kuri Tec® A3236 1/4" - 1" CLD 23 PE
Kuri Tec® A3246 1/4" - 1" CLD 23 PE

[1] Trade name may feature prefix "E" to denote product sold in Europe.
[2] Suffix denotes color for the outermost layer. Color codes are:
    BK - Black
    BL - Blue
    W  - White
    G  - Light Grey
    GR - Green
    DG - Dark Grey
    R  - Red
[3] YYY denotes color for the outermost layer. Color codes are:
    BLK  - Black
    BLU  - Blue
    DGRY - Dark Gray
    GRN  - Green
    LGRY - Light Gray 
    RED  - Red
    WHT  - White
[G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for
    “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state
    laws and the U.S. Safe Drinking Water Act.

    



 
Ace Duraflo Systems, LLC 
3122 West Alpine Street
Santa Ana, CA 92704 
United States 
714-256-0220
Visit this company's website


Facility : # 1 USA

Protective (Barrier) Materials

    Water Water
  Water Contact Contact Contact
Trade Designation Size Restriction Temp Material

Coatings - Pipe - Immediate Return to Service
ePIPE FRS[1] [2] >= 1/2" C. HOT EPOXY

[1] Colors: Red
    Number of Coats: 1
    Maximum Field Use Dry Thickness (in mils): 4-500
    Final Cure Time/Temperature: 15 minutes in water at a service temperature of 23C and
    greater.
    Special Comments: Mix ratio of A:B is 2:1 by volume. Product shall be preconditioned to
    at least 95F prior to mixing. Induction time is at least 10 minutes. Cure with air at a
    minimum of 95F for at least 2 hours. Following the air cure, product cure shall continue
    in water at a service temperature of 23C and greater for 15 minutes with a flow rate of
    1 to 5 liters per minute prior to being placed into service.
[2] Certified for Immediate Return to Service. 



 
Ace Hardware Corporation 
2200 Kensington Ct
Oakbrook, IL 60523 
United States 
630-990-8686
Visit this company's website


Facility : Omaha, NE

Joining and Sealing Materials

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Sealants
ACE PIPE THREAD COMPOUND TFE PASTE >= 1/2" C. HOT SLT
Ace Pipe Thread Compound >= 1/2" C. HOT SLT



 
Ace Roto-Mold 
Division of Den Hartog Industries Inc.
4010 Hospers Drive South 
P.O. Box 425 
Hospers, IA 51238-0425 
United States 
800-342-3408 
712-752-8432
Visit this company's website


Facility : Hospers, IA

Protective (Barrier) Materials

    Water Water
  Water Contact Contact Contact
Trade Designation Size Restriction Temp Material

Tanks[1]
ACTXXXX-LP Cistern Tank [2] CLD 23 MLTPL
ARM-VVVVV [2] CLD 23 MLTPL
AST-XXXX-1W Cistern Tank [2] CLD 23 MLTPL
CBXXXX-YY Batch Tank - Cone Bottom [2] CLD 23 MLTPL
CBXXXX-YY Cone Bottom - Industrial Top [2] CLD 23 MLTPL
CBXXXX-YYY Cone Bottom Tank [2] CLD 23 MLTPL
CBXXXXX-YYY Cone Bottom Tank [2] CLD 23 MLTPL
DWXXXX-120 Double Wall Vertical Tank [2] CLD 23 MLTPL
DWXXXX-YY Double Wall Vertical Tank [2] CLD 23 MLTPL
FMXXXX-YYS Leg Tank [2] CLD 23 MLTPL
FMXXXX-YYY Leg Tank [2] CLD 23 MLTPL
FS01600 Sectional Tank 1600 gal. CLD 23 MLTPL
FS01610 Flat Bottom Leg Tank 1610 gal. CLD 23 MLTPL
FSXXXXX-YY Leg Tank [2] CLD 23 MLTPL
FSXXXXX-YYW Leg Tank [2] CLD 23 MLTPL
GVXXXX-86 Gusset Top Tank [2] CLD 23 MLTPL
GVXXXXX-142 Vertical Polyethylene Storage Tank [2] CLD 23 MLTPL
HEDXXXX-YY Elliptical Tank [2] CLD 23 MLTPL
HEXXXX-YY Elliptical Tank [2] CLD 23 MLTPL
HZXXXXX-YY Horizontal Tank [2] CLD 23 MLTPL
IBFDXX-SET Inductor Tank [2] CLD 23 MLTPL
INFD085 Full Drain Inductor 85 gal. CLD 23 MLTPL
INFDXXX-YY Inductor Tank [2] CLD 23 MLTPL
INXXXX-YYYY Inductor Tank [2] CLD 23 MLTPL
LPXXXX-HT Holding Tank [2] CLD 23 MLTPL
LPXXXX-RT Low Profile Tank [2] CLD 23 MLTPL
LPXXXX-RT Rectangle Tank [2] CLD 23 MLTPL
OCXXXX-YY Batch Tank - Cone Bottom - Open Top [2] CLD 23 MLTPL
OCXXXX-YY Cone Bottom Tank - Open Top [2] CLD 23 MLTPL
OP0210-40 Open Top 210 gal. CLD 23 MLTPL
OPXXXX-YY Batch Tank- Vertical - Open Top [2] CLD 23 MLTPL
PCOXXX-YYZ PCO tank [2] CLD 23 MLTPL
PUXXXX-YY Pickup Tank [2] CLD 23 MLTPL
SBXXXXX Spot Spray [2] CLD 23 MLTPL
SP-XXXX-QQ Applicator Tank [2] CLD 23 MLTPL
SP-XXXXQQ Applicator Tank [2] CLD 23 MLTPL
SP002.8-RT Rectangle Tank – Flat Bottom 2.8 gal. CLD 23 MLTPL
SPBMXX-SQ# Specialty Tank [2] CLD 23 MLTPL
SPBMXXXX-RT Specialty Tank [2] CLD 23 MLTPL
SPXXXX-RT Total Drain Rectangular Tank [2] CLD 23 MLTPL
SPXXXX-SQ# Specialty Tank [2] CLD 23 MLTPL
SPXXXX-UU Rectangle Tank [2] CLD 23 MLTPL
SPXXXX-UU Specialty Tank [2] CLD 23 MLTPL
SPXXXX-VM Applicator Tank [2] CLD 23 MLTPL
SPXXXXX-UU Utility Tank [2] CLD 23 MLTPL
SSPUXXXX-70 Pickup Tank [2] CLD 23 MLTPL
VTXXXX-YY Batch Tank- Vertical [2] CLD 23 MLTPL
VTXXXXX-YYY [2] CLD 23 MLTPL
VTXXXXX-YYYY Vertical Polyethylene Storage Tank [2] CLD 23 MLTPL
WOXXXX-VT Water Only Tank [2] CLD 23 MLTPL

[1] Certified for the following tank/component combinations:
    3/4" fittings/fitting gaskets shall only be used with tanks greater than or equal to 2.8
    gallons.
    1" fittings/fitting gaskets shall only be used with tanks greater than or equal to 3
    gallons.
    1-1/4" and 1-1/2" fittings/fitting gaskets shall only be used with tanks greater than or
    equal to 4 gallons.
    2" fittings/fitting gaskets shall only be used with tanks greater than or equal to 5
    gallons.
    3" fittings/fitting gaskets shall only be used with tanks greater than or equal to 95
    gallons.
    Siphon tubes shall only be used with tanks greater than or equal to 5 gallons.
[2] The trade names include product information represented by alphanumeric code, denoted as
    follows:										
    XXXX, XXXXX, XXXXXX: Tank volume in gallons (2.8 gallons and greater)										
    YY, YYY, YYYYL diameter/width of tank in inches										
    QQ: Customer code										
    Z: Can be S (sump) or W (no sump)										
    UU: Can be RT (Rectangular Tank), SQ (Square Tank), 2P (2in lid), 5N (5 in lid), or any
    other two alphabetical code (customer code)										
    VVVVV: Part number										
    #: Lid size in inches.



 
ACL SRL 
Via G.Falcone, 6
20873 Cavenago Di Brianza 
Italy 
39 02 9501335


Facility : Cavenago Di Brianza, Italy

Mechanical Devices

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Solenoid Valves[G]
D107CNM12/61/DC coil 3/8" CLD 23 MLTPL
E107CM12/61/AC-DC coil 3/8" CLD 23 MLTPL
D207CNM12/61/DC coil 3/8" CLD 23 MLTPL
E207CNM12/61/AC-DC coil 3/8" CLD 23 MLTPL
D117CNM12/61/DC coil 3/8" CLD 23 MLTPL
E107CNM12/61/AC-DC coil 3/8" CLD 23 MLTPL
D117CM12/61/DC coil 3/8" CLD 23 MLTPL
D107CM12/61/DC coil 3/8" CLD 23 MLTPL
E207CM12/61/AC-DC coil 3/8" CLD 23 MLTPL
D207CM12/61/DC coil 3/8" CLD 23 MLTPL
D207DNM12/61/DC coil 1/2" CLD 23 MLTPL
D107DNM12/61/DC coil 1/2" CLD 23 MLTPL
E107DM12/61/AC-DC coil 1/2" CLD 23 MLTPL
E107DNM12/61/AC-DC coil 1/2" CLD 23 MLTPL
E207DNM12/61/AC-DC coil 1/2" CLD 23 MLTPL
D117DNM12/61/DC coil 1/2" CLD 23 MLTPL
D107DM12/61/DC coil 1/2" CLD 23 MLTPL
D117DM12/61/DC coil 1/2" CLD 23 MLTPL
E207DM12/61/AC-DC coil 1/2" CLD 23 MLTPL
D207DM12/61/DC coil 1/2" CLD 23 MLTPL
E107ENM18/61/AC-DC coil 3/4" CLD 23 MLTPL
E107EM18/61/AC-DC coil 3/4" CLD 23 MLTPL
D117ENM18/61/DC coil 3/4" CLD 23 MLTPL
D207ENM18/61/DC coil 3/4" CLD 23 MLTPL
D107ENM18/61/DC coil 3/4" CLD 23 MLTPL
E207ENM18/61/AC-DC coil 3/4" CLD 23 MLTPL
D107EM18/61/DC coil 3/4" CLD 23 MLTPL
D117EM18/61/DC coil 3/4" CLD 23 MLTPL
E207EM18/61/AC-DC coil 3/4" CLD 23 MLTPL
D207EM18/61/DC coil 3/4" CLD 23 MLTPL
D107FNM25/61/DC coil 1" CLD 23 MLTPL
D117FNM25/61/DC coil 1" CLD 23 MLTPL
D207FNM25/61/DC coil 1" CLD 23 MLTPL
E107FM25/61/AC-DC coil 1" CLD 23 MLTPL
E107FNM25/61/AC-DC coil 1" CLD 23 MLTPL
E207FNM25/61/AC-DC coil 1" CLD 23 MLTPL
D107FM25/61/DC coil 1" CLD 23 MLTPL
D117FM25/61/DC coil 1" CLD 23 MLTPL
E207FM25/61/AC-DC coil 1" CLD 23 MLTPL
D207FM25/61/DC coil 1" CLD 23 MLTPL
D107GNM30/61/DC coil 1 1/4" CLD 23 MLTPL
E107GM30/61/AC-DC coil 1 1/4" CLD 23 MLTPL
E207GNM30/61/AC-DC coil 1 1/4" CLD 23 MLTPL
D207GNM30/61/DC coil 1 1/4" CLD 23 MLTPL
D117GNM30/61/DC coil 1 1/4" CLD 23 MLTPL
E107GNM30/61/AC-DC coil 1 1/4" CLD 23 MLTPL
D107GM30/61/DC coil 1 1/4" CLD 23 MLTPL
E107GM37/61/AC-DC coil 1 1/4" CLD 23 MLTPL
D107GM37/61/DC coil 1 1/4" CLD 23 MLTPL
D117GM30/61/DC coil 1 1/4" CLD 23 MLTPL
D117GM37/61/DC coil 1 1/4" CLD 23 MLTPL
E207GM30/61/AC-DC coil 1 1/4" CLD 23 MLTPL
D207GM30/61/DC coil 1 1/4" CLD 23 MLTPL
E207GM37/61/AC-DC coil 1 1/4" CLD 23 MLTPL
D117GNM37/61/DC coil 1 1/4" CLD 23 MLTPL
E207GNM37/61/AC-DC coil 1 1/4" CLD 23 MLTPL
D107GNM37/61/DC coil 1 1/4" CLD 23 MLTPL
D207GNM37/61/DC coil 1 1/4" CLD 23 MLTPL
D207GM37/61/DC coil 1 1/4" CLD 23 MLTPL
E107GNM37/61/AC-DC coil 1 1/4" CLD 23 MLTPL
E107HM37/61/AC-DC coil 1 1/2" CLD 23 MLTPL
D107HM37/61/DC coil 1 1/2" CLD 23 MLTPL
D117HM37/61/DC coil 1 1/2" CLD 23 MLTPL
E207HM37/61/AC-DC coil 1 1/2" CLD 23 MLTPL
D117HNM37/61/DC coil 1 1/2" CLD 23 MLTPL
D107HNM37/61/DC coil 1 1/2" CLD 23 MLTPL
D207HM37/61/DC coil 1 1/2" CLD 23 MLTPL
E207HNM37/61/AC-DC coil 1 1/2" CLD 23 MLTPL
E107HNM37/61/AC-DC coil 1 1/2" CLD 23 MLTPL
D207HNM37/61/DC coil 1 1/2" CLD 23 MLTPL
E107IM50/61/AC-DC coil 2" CLD 23 MLTPL
D107IM50/61/DC coil 2" CLD 23 MLTPL
D117IM50/61/DC coil 2" CLD 23 MLTPL
E207IM50/61/AC-DC coil 2" CLD 23 MLTPL
D117INM50/61/DC coil 2" CLD 23 MLTPL
E107INM50/61/AC-DC coil 2" CLD 23 MLTPL
D207IM50/61/DC coil 2" CLD 23 MLTPL
D207INM50/61/DC coil 2" CLD 23 MLTPL
D107INM50/61/DC coil 2" CLD 23 MLTPL
E207INM50/61/AC-DC coil 2" CLD 23 MLTPL
D117MNM75/61/DC coil 2 1/2" CLD 23 MLTPL
D207MNM75/61/DC coil 2 1/2" CLD 23 MLTPL
E207MNM75/61/AC-DC coil 2 1/2" CLD 23 MLTPL
D107MM75/61/DC coil 2 1/2" CLD 23 MLTPL
D107MNM75/61/DC coil 2 1/2" CLD 23 MLTPL
E107MNM75/61/AC-DC coil 2 1/2" CLD 23 MLTPL
E107MM75/61/AC-DC coil 3" CLD 23 MLTPL
E107RM75/61/AC-DC coil 3" CLD 23 MLTPL
D107RM75/61/DC coil 3" CLD 23 MLTPL
D117MM75/61/DC coil 3" CLD 23 MLTPL
D117RM75/61/DC coil 3" CLD 23 MLTPL
E207MM75/61/AC-DC coil 3" CLD 23 MLTPL
D207MM75/61/DC coil 3" CLD 23 MLTPL
E207RM75/61/AC-DC coil 3" CLD 23 MLTPL
E107RNM75/61/AC-DC coil 3" CLD 23 MLTPL
D207RNM75/61/DC coil 3" CLD 23 MLTPL
D207RM75/61/DC coil 3" CLD 23 MLTPL
D117RNM75/61/DC coil 3" CLD 23 MLTPL
E207RNM75/61/AC-DC coil 3" CLD 23 MLTPL
D107RNM75/61/DC coil 3" CLD 23 MLTPL

[G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for
    “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state
    laws and the U.S. Safe Drinking Water Act.

    



 
Acme Chemicals Malaysia Sdn. Bhd. 
Lot 606, Persiaran Raja Lumu
Pandamaran Industrial Estate, Klang 
42000 Selangor 
Malaysia 
60 3 3175 6088
Visit this company's website


Facility : Selangor, Malaysia

Process Media

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Adsorption Media
ACM OPC 200 XZ[1] [2] CLD 23 ZEO
ACM OPC 200 XZB[1] [2] CLD 23 ZEO
ACM OPC 200Z[1] [2] CLD 23 ZEO

[1] Certification is based on a bed depth up to 65 cm with a minimum flow rate of 3.82 cubic
    meter per hour per sq. meter.
[2] Certified for mesh size 0.8 x 1.5 mm.

NOTE: Certified for water treatment plant applications.
      This product has not been evaluated for point of use applications.


 
ACPP Custom Plumbing Parts, ULC 
10037-96 Avenue
Westlock, AB T7P-2P9 
Canada 
780-349-6511


Facility : Westlock, Alberta, Canada

Mechanical Devices

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Manifolds
Copper Manifolds [1] C. HOT CU

[1] The following part numbers, configurations and sizes are Certified.  All manifolds are
    72" long (unless otherwise noted) and may be cut to the desired length.
    
    Copper Manifolds with Copper Ports:
    
    Pipe run 1", 1 1/4", 1 1/2" or 2" with 24 1/2", 3/4", or 1" copper outlets on 3" CTRS.
    
    CC1005024 1 X 1/2 CU
    CC1255024 1 1/4 X 1/2 CU
    CC1251024 1 1/4 X 1 CU
    CC1505024 1 1/2 X 1/2 CU
    CC1501024 1 1/2 X 1 CU
    CC2005024 2 X 1/2 CU
    CC1007524 1 X 3/4 CU
    CC1257524 1 1/4 X 3/4 CU
    CC1507524 1 1/2 X 3/4 CU
    CC2007524 2 X 3/4 CU
    CC2001024 2 X 1 CU
    
    Pipe run 1", 1 1/4", 1 1/2" or 2" with 18 1/2", 3/4", or 1" copper outlets on 4" CTRS
    
    CC1005018 1 X 1/2 CU
    CC1255018 1 1/4 X 1/2 CU
    CC1505018 1 1/2 X 1/2 CU
    CC2005018 2 X 1/2 CU
    CC1007518 1 X 3/4 CU
    CC1257518 1 1/4 X 3/4 CU
    CC1507518 1 1/2 X 3/4 CU
    CC2007518 2 X 3/4 CU
    CC1251018 1 1/4 X 1 CU
    CC1501018 1 1/2 X 1 CU
    CC2001018 2 X 1 CU
    
    Pipe run 1", 1 1/4", 1 1/2" or 2" with 12 1/2", 3/4", or 1" copper outlets on 6" CTRS.
    
    CC1005012ER 1 X 1/2 CU
    CC1255012ER 1 1/4 X 1/2 CU
    CC1505012ER 1 1/2 X 1/2 CU
    CC2005012ER 2 X 1/2 CU
    CC1007512ER 1 X 3/4 CU
    CC1257512ER 1 1/4 X 3/4 CU
    CC1507512ER 1 1/2 X 3/4 CU
    CC2007512ER 2 X 3/4 CU
    CC1251012ER 1 1/4 X 1 CU
    CC1501012ER 1 1/2 X 1 CU
    CC2001012ER 2 X 1 CU
    
    Pipe run 62" long, 1" with 30 1/2" copper outlets on 2" CTRS.
    
    CC1005030 1 X 1/2 CU
    
    Compact Headers - Pipe run 1" with 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, or 12 1/2" copper
    outlets on 1 1/2" CTRS.
    
    CC1005002 1 X 1/2 CU
    CC1005003 1 X 1/2 CU
    CC1005004 1 X 1/2 CU
    CC1005005 1 X 1/2 CU
    CC1005006 1 X 1/2 CU
    CC1005007 1 X 1/2 CU
    CC1005008 1 X 1/2 CU
    CC1005009 1 X 1/2 CU
    CC1005010 1 X 1/2 CU
    CC1005011 1 X 1/2 CU
    CC1005012 1 X 1/2 CU
    
    Speedy Copper Headers - closed one end and reduced 3/4" female sweat the other end.
    
    SC1005002RC 1 X 1/2 CU
    SC1005003RC 1 X 1/2 CU
    SC1005004RC 1 X 1/2 CU
    SC1005005RC 1 X 1/2 CU
    SC1005006RC 1 X 1/2 CU
    SC1005007RC 1 X 1/2 CU
    SC1005008RC 1 X 1/2 CU
    SC1005009RC 1 X 1/2 CU
    SC1005010RC 1 X 1/2 CU
    SC1005011RC 1 X 1/2 CU
    SC1005012RC 1 X 1/2 CU
    
    Speedy Copper Headers - closed one end and 1" plain the other end.
    
    SC1005002PL 1 X 1/2 CU
    SC1005003PL 1 X 1/2 CU
    SC1005004PL 1 X 1/2 CU
    SC1005005PL 1 X 1/2 CU
    SC1005006PL 1 X 1/2 CU
    SC1005007PL 1 X 1/2 CU
    SC1005008PL 1 X 1/2 CU
    SC1005009PL 1 X 1/2 CU
    SC1005010PL 1 X 1/2 CU
    SC1005011PL 1 X 1/2 CU
    SC1005012PL 1 X 1/2 CU
    
    Copper Manifolds with PEX Valves:
    
    Type L Copper Manifold with a Lead Free PEX Valve
    1", 1 1/4", 1 1/2", and 2" Copper Headers with 1/2" Lead Free PEX Valves on 3" Center
    
    CX1005024V-LF 1" x 1/2" Copper outlets with a 1/2" Lead free PEX Valve
    CX1255024V-LF 1 1/4" x 1/2" Copper outlets with a 1/2" Lead free PEX Valve
    CX1505024V-LF 1 1/2" x 1/2" Copper outlets with a 1/2" Lead free PEX Valve
    CX2005024V-LF 2" x 1/2" Copper outlets with a 1/2" Lead free PEX Valve
    
    1" or 1 1/4" Copper Header with 2-12 1/2" Lead Free PEX Valves on 2" Centers
    CVP1005002-LF
    CVP1005003-LF
    CVP1005004-LF
    CVP1005005-LF
    CVP1005006-LF
    CVP1005007-LF
    CVP1005008-LF
    CVP1005009-LF
    CVP1005010-LF
    CVP1005011-LF
    CVP1005012-LF
    CVP1255002-LF
    CVP1255002-LF
    CVP1255003-LF
    CVP1255004-LF
    CVP1255005-LF
    CVP1255006-LF
    CVP1255007-LF
    CVP1255008-LF
    CVP1255009-LF
    CVP1255010-LF
    CVP1255011-LF
    CVP1255012-LF
    



 
Action Technology 
10610 State Highway 10
Clinton, IL 61727 
United States 
217-935-1066


Facility : Clinton, IL

Pipes and Related Products

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Tubing/Hose
AT Alpha PE Series .17" - .5" D. HOT PE



 
Activated Carbon Solutions Inc 
5757 West Century Boulevard
Suite700 
Los Angeles, CA 90045 
United States 
424-419-4009
Visit this company's website


Facility : # 1 India

Process Media

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Granular Activated Carbon[1]
WAC-1020 [3] CLD 23 GAC
WAC-1020 CAT [2] CLD 23 GAC
WAC-1020 WW [3] CLD 23 GAC
WAC-1030 [3] CLD 23 GAC
WAC-1030 CAT [2] CLD 23 GAC
WAC-1030 WW [3] CLD 23 GAC
WAC-1032 CAT [2] CLD 23 GAC
WAC-1220 [3] CLD 23 GAC
WAC-1220 CAT [2] CLD 23 GAC
WAC-1220 WW [3] CLD 23 GAC
WAC-1230 [3] CLD 23 GAC
WAC-1230 WW [3] CLD 23 GAC
WAC-1235 CAT [2] CLD 23 GAC
WAC-1240 [3] CLD 23 GAC
WAC-1240 WW [3] CLD 23 GAC
WAC-1830 CAT [2] CLD 23 GAC
WAC-1835 CAT [2] CLD 23 GAC
WAC-2050 CAT [2] CLD 23 GAC
WAC-3010 CAT [2] CLD 23 GAC
WAC-3014 CAT [2] CLD 23 GAC
WAC-3070 CAT [2] CLD 23 GAC
WAC-3080 CAT [2] CLD 23 GAC
WAC-4080 [3] CLD 23 GAC
WAC-4080 WW [3] CLD 23 GAC
WAC-410 CAT [2] CLD 23 GAC
WAC-610 CAT [2] CLD 23 GAC
WAC-616 CAT [2] CLD 23 GAC
WAC-816 [3] CLD 23 GAC
WAC-816 WW [3] CLD 23 GAC
WAC-820 [3] CLD 23 GAC
WAC-820 CAT [2] CLD 23 GAC
WAC-820 WW [3] CLD 23 GAC
WAC-830 [3] CLD 23 GAC
WAC-840 [3] CLD 23 GAC
WAC-840 CAT [2] CLD 23 GAC
WAC-840 WW [3] CLD 23 GAC

[1] The carbon source is coconut shell.
[2] Certified for mesh sizes: 4 x 10, 6 x 16, 8 x 20, 8 x 40, 10 x 20, 10 x 30, 10 x 32, 12
    x 20, 12 x 35, 12 x 40, 18 x 30, 18 x 35, 20 x 50, 30 x 70, 30 x 80, 30 x 100, 30 x 140.
[3] Certified for mesh sizes: 4 x 8, 4 x 10, 6 x 10, 6 x 12, 6 x 16, 8 x 16, 8 x 20, 8 x 40,
    8 x 30, 10 x 20, 10 x 30, 10 x 32, 12 x 20, 12 x 30, 12 x 35, 12 x 40, 14 x 35, 18 x 30,
    18 x 35, 18 x 40, 20 x 40, 20 x 50, 30 x 20, 30 x 60, 30 x 70, 30 x 80, 30 x 100, 30 x
    140, 35 x 60, 40 x 80, 40 x 100, 40 x 140, 50 x 100, 50 x 200, 60 x 140, 60 x 200, 60 x
    320, 80 x 200, 80 x 325, -100, -200, -325.

Powdered Activated Carbon[1]
WAC-200 [3] CLD 23 PAC
WAC-325 [3] CLD 23 PAC
WAC-5020 WW [3] CLD 23 PAC
WAC-8020 [3] CLD 23 PAC
WAC-8032 [3] CLD 23 PAC

[1] The carbon source is coconut shell.
[3] Certified for mesh sizes: 4 x 8, 4 x 10, 6 x 10, 6 x 12, 6 x 16, 8 x 16, 8 x 20, 8 x 40,
    8 x 30, 10 x 20, 10 x 30, 10 x 32, 12 x 20, 12 x 30, 12 x 35, 12 x 40, 14 x 35, 18 x 30,
    18 x 35, 18 x 40, 20 x 40, 20 x 50, 30 x 20, 30 x 60, 30 x 70, 30 x 80, 30 x 100, 30 x
    140, 35 x 60, 40 x 80, 40 x 100, 40 x 140, 50 x 100, 50 x 200, 60 x 140, 60 x 200, 60 x
    320, 80 x 200, 80 x 325, -100, -200, -325.

NOTE: Certified for water treatment plant applications.
      This product has not been evaluated for point of use applications.


 
Activcarb 
SF No. 270/ 1, Chinnaputhur
Dharapuram, Dist Tirupur 
Tamil Nadu 638657 
India 
91 999 4063307


Facility : Tamil Nadu, India

Process Media

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Granular Activated Carbon[1]
Acb100 [2] CLD 23 GAC
Acb40 [2] CLD 23 GAC
Acb45 [2] CLD 23 GAC
Acb50 [2] CLD 23 GAC
Acb55 [2] CLD 23 GAC
Acb60 [2] CLD 23 GAC
Acb65 [2] CLD 23 GAC
Acb70 [2] CLD 23 GAC
Acb75 [2] CLD 23 GAC
Acb80 [2] CLD 23 GAC
Acb85 [2] CLD 23 GAC
Acb90 [2] CLD 23 GAC
Acb95 [2] CLD 23 GAC

[1] The carbon source is coconut shell.
[2] Certified for the following mesh sizes: 3x6, 3x30, 6x8, 4x8, 6x12, 6x16, 8x16, 8x20,
    8x30, 12x30, 12x40, 14x25, 16x35, 16x40, 18x35, 18x40, 20x40, 20x50, 20x60, 20x70,
    30x50, 30x60, 30x70, 30x80, 35x60, 35x70 and 40x80.

Powdered Activated Carbon[1]
Acb1000 [3] CLD 23 PAC
Acb1050 [3] CLD 23 PAC
Acb1100 [3] CLD 23 PAC
Acb1150 [3] CLD 23 PAC
Acb1200 [3] CLD 23 PAC
Acb1250 [3] CLD 23 PAC
Acb1300 [3] CLD 23 PAC
Acb1350 [3] CLD 23 PAC
Acb1400 [3] CLD 23 PAC
Acb1450 [3] CLD 23 PAC
Acb1500 [3] CLD 23 PAC
Acb950 [3] CLD 23 PAC

[1] The carbon source is coconut shell.
[3] Certified for the following mesh sizes: 40x140, 50x140, 50x200, 80x140, 80x200, 80x325,
    100x325, -200 and -325.

NOTE: Certified for water treatment plant applications.
      This product has not been evaluated for point of use applications.


 
Active Char Products Pvt. Ltd. 
B No. 615, IDA
Binanipuram, Edayar 
Ernakulam, Kerala 683502 
India 
91 484 2556514
Visit this company's website


Facility : Ernakulam, Kerala, India

Process Media

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Granular Activated Carbon[1]
MF CARB CT 820 [2] CLD 23 GAC
MF CARB CT 1020 [2] CLD 23 GAC
MF CARB CT 1030 [2] CLD 23 GAC
MF CARB CT 1032 [2] CLD 23 GAC
MF CARB CT 1220 [2] CLD 23 GAC
MF CARB CT 1235 [2] CLD 23 GAC
MF CARB CT 1830 [2] CLD 23 GAC
MF CARB CT 1835 [2] CLD 23 GAC
MF CARB CT 2050 [2] CLD 23 GAC
MF CARB CT 3010 [2] CLD 23 GAC
MF CARB CT 3014 [2] CLD 23 GAC
MF CARB CT 3070 [2] CLD 23 GAC
MF CARB CT 3080 [2] CLD 23 GAC
MF CARB CT 410 [2] CLD 23 GAC
MF CARB CT 610 [2] CLD 23 GAC
MF CARB CT 616 [2] CLD 23 GAC
MF CARB CT 840 [2] CLD 23 GAC
MF CARB WT 1020 [3] CLD 23 GAC
MF CARB WT 1020 WW [3] CLD 23 GAC
MF CARB WT 1030 [3] CLD 23 GAC
MF CARB WT 1030 WW [3] CLD 23 GAC
MF CARB WT 1032 [3] CLD 23 GAC
MF CARB WT 1032 WW [3] CLD 23 GAC
MF CARB WT 1220 [3] CLD 23 GAC
MF CARB WT 1220 WW [3] CLD 23 GAC
MF CARB WT 1230 [3] CLD 23 GAC
MF CARB WT 1230 WW [3] CLD 23 GAC
MF CARB WT 1235 [3] CLD 23 GAC
MF CARB WT 1235 WW [3] CLD 23 GAC
MF CARB WT 1240 [3] CLD 23 GAC
MF CARB WT 1240 WW [3] CLD 23 GAC
MF CARB WT 1435 [3] CLD 23 GAC
MF CARB WT 1435 WW [3] CLD 23 GAC
MF CARB WT 1830 [3] CLD 23 GAC
MF CARB WT 1830 WW [3] CLD 23 GAC
MF CARB WT 1835 [3] CLD 23 GAC
MF CARB WT 1835 WW [3] CLD 23 GAC
MF CARB WT 1840 [3] CLD 23 GAC
MF CARB WT 1840 WW [3] CLD 23 GAC
MF CARB WT 2040 [3] CLD 23 GAC
MF CARB WT 2040 WW [3] CLD 23 GAC
MF CARB WT 2050 [3] CLD 23 GAC
MF CARB WT 2050 WW [3] CLD 23 GAC
MF CARB WT 3010 [3] CLD 23 GAC
MF CARB WT 3010 WW [3] CLD 23 GAC
MF CARB WT 3014 [3] CLD 23 GAC
MF CARB WT 3014 WW [3] CLD 23 GAC
MF CARB WT 3020 [3] CLD 23 GAC
MF CARB WT 3020 WW [3] CLD 23 GAC
MF CARB WT 3060 [3] CLD 23 GAC
MF CARB WT 3060 WW [3] CLD 23 GAC
MF CARB WT 3070 [3] CLD 23 GAC
MF CARB WT 3070 WW [3] CLD 23 GAC
MF CARB WT 3080 [3] CLD 23 GAC
MF CARB WT 3080 WW [3] CLD 23 GAC
MF CARB WT 3560 [3] CLD 23 GAC
MF CARB WT 3560 WW [3] CLD 23 GAC
MF CARB WT 4010 [3] CLD 23 GAC
MF CARB WT 4010 WW [3] CLD 23 GAC
MF CARB WT 4014 [3] CLD 23 GAC
MF CARB WT 4014 WW [3] CLD 23 GAC
MF CARB WT 4080 [3] CLD 23 GAC
MF CARB WT 4080 WW [3] CLD 23 GAC
MF CARB WT 410 [3] CLD 23 GAC
MF CARB WT 410 WW [3] CLD 23 GAC
MF CARB WT 48 [3] CLD 23 GAC
MF CARB WT 48 WW [3] CLD 23 GAC
MF CARB WT 5010 [3] CLD 23 GAC
MF CARB WT 5010 WW [3] CLD 23 GAC
MF CARB WT 610 [3] CLD 23 GAC
MF CARB WT 610 WW [3] CLD 23 GAC
MF CARB WT 612 [3] CLD 23 GAC
MF CARB WT 612 WW [3] CLD 23 GAC
MF CARB WT 616 [3] CLD 23 GAC
MF CARB WT 616 WW [3] CLD 23 GAC
MF CARB WT 816 [3] CLD 23 GAC
MF CARB WT 816 WW [3] CLD 23 GAC
MF CARB WT 820 [3] CLD 23 GAC
MF CARB WT 820 WW [3] CLD 23 GAC
MF CARB WT 830 WW [3] CLD 23 GAC
MF CARB WT 840 [3] CLD 23 GAC
MF CARB WT 840 WW [3] CLD 23 GAC
MF CARB WT B830 [3] CLD 23 GAC

[1] The carbon source is coconut shell.
[2] Certified for mesh sizes: 4 x 10, 6 x 16, 8 x 20, 8 x 40, 10 x 20, 10 x 30, 10 x 32, 12
    x 20, 12 x 35, 12 x 40, 18 x 30, 18 x 35, 20 x 50, 30 x 70, 30 x 80,
    30 x 100, 30 x 140.
[3] Certified for mesh sizes: 4 x 8, 4 x 10, 6 x 10, 6 x 12, 6 x 16, 8 x 16, 8 x 20, 8 x 40,
    8 x 30, 10 x 20, 10 x 30, 10 x 32, 12 x 20, 12 x 30, 12 x 35, 12 x 40, 14 x 35, 18 x 30,
    18 x 35, 18 x 40, 20 x 40, 20 x 50, 30 x 20, 30 x 60, 30 x 70, 30 x 80, 30 x 100, 30 x
    140, 35 x 60, 40 x 80, 40 x 100, 40 x 140, 50 x 100, 50 x 200, 60 x 140, 60 x 200, 60 x
    320, 80 x 200, 80 x 325, -100, -200, -325.

Powdered Activated Carbon[1]
MF CARB WT -200 [3] CLD 23 PAC
MF CARB WT -200 WW [3] CLD 23 PAC
MF CARB WT -325 [3] CLD 23 PAC
MF CARB WT -325 WW [3] CLD 23 PAC
MF CARB WT 5020 [3] CLD 23 PAC
MF CARB WT 5020 WW [3] CLD 23 PAC
MF CARB WT 6014 [3] CLD 23 PAC
MF CARB WT 6014 WW [3] CLD 23 PAC
MF CARB WT 6020 [3] CLD 23 PAC
MF CARB WT 6020 WW [3] CLD 23 PAC
MF CARB WT 6032 [3] CLD 23 PAC
MF CARB WT 6032 WW [3] CLD 23 PAC
MF CARB WT 8020 [3] CLD 23 PAC
MF CARB WT 8020 WW [3] CLD 23 PAC
MF CARB WT 8032 [3] CLD 23 PAC
MF CARB WT 8032 WW [3] CLD 23 PAC
MF CARB WT PAC [3] CLD 23 PAC
MF CARB WT PAC WW [3] CLD 23 PAC

[1] The carbon source is coconut shell.
[3] Certified for mesh sizes: 4 x 8, 4 x 10, 6 x 10, 6 x 12, 6 x 16, 8 x 16, 8 x 20, 8 x 40,
    8 x 30, 10 x 20, 10 x 30, 10 x 32, 12 x 20, 12 x 30, 12 x 35, 12 x 40, 14 x 35, 18 x 30,
    18 x 35, 18 x 40, 20 x 40, 20 x 50, 30 x 20, 30 x 60, 30 x 70, 30 x 80, 30 x 100, 30 x
    140, 35 x 60, 40 x 80, 40 x 100, 40 x 140, 50 x 100, 50 x 200, 60 x 140, 60 x 200, 60 x
    320, 80 x 200, 80 x 325, -100, -200, -325.

NOTE: Certified for water treatment plant applications.
      This product has not been evaluated for point of use applications.


 
Adam Carbons Pvt. Ltd. 
264, Grandpass Road
Colombo 01400 
Sri Lanka 
94 72 7434464
Visit this company's website


Facility : Giriulla, Sri Lanka

Process Media

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Granular Activated Carbon[1]
AC Virgin Granular [2] CLD 23 CARBON
AC Virgin Granular Acid Washed [2] CLD 23 CARBON
AC Virgin Granular Impregnated [2] CLD 23 CARBON

[1] The carbon source is coconut shell.
[2] Certified for the following mesh sizes: 4x8, 8x16, 8x30, 12x30, 12x40, 30x60, 30x80,
    40x80.

NOTE: Certified for water treatment plant applications.
      This product has not been evaluated for point of use applications.


 
AdEdge Technologies, Inc. 
5152 Belle Wood Court
Suites A 
Burford, GA 30518 
United States 
678-835-0052


Facility : Quincy, IL

Process Media

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Oxidative Media
AD26 [1] CLD 23 MNDOX

[1] Certified for the following mesh sizes: 8 x 20, 20 x 40.

NOTE: Certified for water treatment plant applications.
      This product has not been evaluated for point of use applications.


 
Adept Fluidyne Pvt. Ltd. 
Plot 4, S No. 17/1 - B, Kothrud
Industrial Estate, Pune 
Maharashtra 411 038 
India 
91 202 5464551
Visit this company's website


Facility : Pune, Maharashtra, India

Mechanical Devices

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Water Meters
MagFlow 6410 PP 25 mm - 500 mm CLD 23 MLTPL



 
Adhesive R&D, Inc. 
4603 Anderson Drive
Eau Claire, WI 54703 
United States 
715-832-4557
Visit this company's website


Facility : Eau Claire, WI

Joining and Sealing Materials

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Thread Compounds
DFM 555 [1] CLD 23 SLT
DFM 63 [1] CLD 23 SLT
DFM 64 [1] CLD 23 SLT
DFM 65 [1] CLD 23 SLT
DFM 66 [1] CLD 23 SLT
DFM 67 [1] CLD 23 SLT
DFM 68 [1] CLD 23 SLT
FMB64 [1] CLD 23 SLT
FMB65 [1] CLD 23 SLT
FMB66 [1] CLD 23 SLT
RubberMAX iPipe 70 [1] CLD 23 SLT
RubberMAX iPipe 71 [1] CLD 23 SLT
RubberMAX iPipe 72 [1] CLD 23 SLT
RubberMAX iPipe 73 [1] CLD 23 SLT

[1] Certified for a maximum of 18.5 joints per liter.



 
Adhesives Technology Corp. 
450 East Copans Road
Pompano Beach, FL 33064 
United States 
954-461-2335


Facility : # 2 Germany

Joining and Sealing Materials

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Adhesives
ULTRABOND ACRYL-8CC [1] D. HOT VE
ULTRABOND HYB-2CC [1] C. HOT PUR

[1] Certified for use as an anchoring adhesive for installing thread rods (less than or
    equal to 1.3 inches in diameter) in concrete or masonry for water treatment applications.

NOTE: Only products bearing the NSF Mark on the products, product packaging, and/or
      documentation shipped with the product are certified.


Adhesives Technology Corp. (ATC) 
450 East Copans Road
Pompano Beach, FL 33064 
United States 
800-892-1880 
Visit this company's website


Facility : # 1 Germany

Joining and Sealing Materials

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Adhesives
ULTRABOND 365CC 13.2 fl. oz. [1] C. HOT VE
ULTRABOND 365CC 19.8 fl. oz. [1] C. HOT VE

[1] Certified for use as an anchoring adhesive for installing threaded rods (less than or
    equal to 6 mm - 36 mm or 1/4" - 1-3/8" in diameter) in concrete for water treatment
    applications.



 
Adolf Würth GmbH & Co. KG 
Produktmanagement Chemie, Postfach
74650 Künzelsau 
Germany 
49 794 015 2007


Facility : # 1 Switzerland

Joining and Sealing Materials

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Adhesives
Würth® DOS Lagersicherung hochfest (0893 603) >= 1/2" C. HOT ADH
Würth® DOS Flächendicht orange (0893 574) >= 1/2" C. HOT ADH
Würth® DOS Klebfix EASY PEN (0893 090) >= 1/2" CLD 23 ADH
Würth® DOS Klebfix (0893 09) >= 1/2" CLD 23 ADH
Würth® DOS Schraubensicherung Hochfest >= 1/2" C. HOT ADH
Würth® DOS Schraubensicherung Mittelfest >= 1/2" C. HOT ADH
Würth Rohrdicht PLUS (0893 577 300) >= 1/2" C. HOT ADH

Sealants
Würth® DOS Flächendicht grün (0893 573) >= 1/2" C. HOT SLT

Thread Compounds
Würth® DOS Rohrdicht mit PTFE >= 1/2" C. HOT TC
Würth® DOS Rohrdicht[1] >= 1/2" C. HOT TC
Würth® DOS Schraubensicherung Hochfest >= 1/2" C. HOT TC

[1] Certification is based on a minimum cure of 72 hours at 75°F.



 
Adolf Würth GmbH & Co. KG 
Reinhold-Würth-Str. 12-16
74653 Künzelsau-Gaisbach 
Germany 
49 7940 15 0


Facility : # 2 Germany

Joining and Sealing Materials

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Adhesives
Atrion AVM TOP QUATTRO [1] D. HOT VE
WIT-PE 1000 [1] D. HOT EPOXY
WIT-PE 500 [1] D. HOT EPOXY
WIT-UH 300 [1] C. HOT PUR
WIT-VH 300 [1] C. HOT PUR
WIT-VM 250 [1] D. HOT VE
WIT-VM 300 [1] C. HOT PUR

[1] Certified for use as an anchoring adhesive for installing thread rods (less than or
    equal to 1.3 inches in diameter) in concrete or masonry for water treatment applications.

NOTE: Only products bearing the NSF Mark on the product, product packaging, and/or
      documentation shipped with the product are Certified.


 
Adolf Würth GmbH & Co. KG 
Reinhold-Würth-Strasse 12-17
D-74650 Künzelsau, Baden-Wurttemberg 
Germany 
49 7940150
Visit this company's website


Facility : # 1 Germany

Joining and Sealing Materials

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Sealants[G]
SILICONE ACETATE, FOOD GRADE / ACETATSILIKON LEBENSMITTEL >= 1/2" CLD 23 SLT

[G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for
    “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state
    laws and the U.S. Safe Drinking Water Act.

    



 
Advance Products & Systems 
108 Asset Avenue
Scott, LA 70583 
United States 
800-315-6009 
337-233-6116
Visit this company's website
Lined Cylinder Pipe (LCP) >= 16" CLD 23 MLTPL
[1] Certification includes authorized gaskets, lubricant, form oil, joint rings, and curing
    compound.
[2] XX represents a 2- or 3- digit pipe diameter.



Facility : South Beloit, IL

Pipes and Related Products

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Fittings[1]
Concrete Pressure Pipe Fittings 16" - 144" CLD 23 MLTPL
Concrete Pressure Pipe Fittings (C300) 16" - 144" CLD 23 MLTPL
Concrete Pressure Pipe Fittings (E) 16" - 144" CLD 23 MLTPL
Concrete Pressure Pipe Fittings (E-301) 16" - 144" CLD 23 MLTPL
Concrete Pressure Pipe Fittings (E301) 16" - 144" CLD 23 MLTPL
Concrete Pressure Pipe Fittings (ECP) 16" - 144" CLD 23 MLTPL
Concrete Pressure Pipe Fittings (L) 16" - 144" CLD 23 MLTPL
Concrete Pressure Pipe Fittings (L-301) 16" - 144" CLD 23 MLTPL
Concrete Pressure Pipe Fittings (L301) 16" - 144" CLD 23 MLTPL
Concrete Pressure Pipe Fittings (LCP) 16" - 144" CLD 23 MLTPL

[1] Certification includes lubricant, form oil, joint rings, and patch compound. Gaskets
    used with this system must be NSF Certified for the applicable diameter pipe size.

Pipe[1]
Embedded Cylider Pipe (C300) 24" - 144" CLD 23 MLTPL
Embedded Cylider Pipe (E) 24" - 144" CLD 23 MLTPL
Embedded Cylider Pipe (E-301) 24" - 144" CLD 23 MLTPL
Embedded Cylider Pipe (E301) 24" - 144" CLD 23 MLTPL
Embedded Cylider Pipe (L) 24" - 144" CLD 23 MLTPL
Embedded Cylider Pipe (L-301) 24" - 144" CLD 23 MLTPL
Embedded Cylider Pipe (L301) 24" - 144" CLD 23 MLTPL
Embedded Cylider Pipe (LCP) 24" - 144" CLD 23 MLTPL
Embedded Cylinder Pipe (ECP) 24" - 144" CLD 23 MLTPL
Lined Cylinder Pipe (L) 16" - 48" CLD 23 MLTPL
Lined Cylinder Pipe (L-301) 16" - 48" CLD 23 MLTPL
Lined Cylinder Pipe (L301) 16" - 48" CLD 23 MLTPL
Lined Cylinder Pipe (LCP) 16" - 48" CLD 23 MLTPL

[1] Certification includes lubricant, form oil, joint rings, and patch compound. Gaskets
    used with this system must be NSF Certified for the applicable diameter pipe size.



Facility : Grand Prairie, TX

Pipes and Related Products

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Fittings
Concrete Pressure Pipe Fittings >= 10" CLD 23 MLTPL
Concrete Pressure Pipe Fittings (B) >= 10" CLD 23 MLTPL
Concrete Pressure Pipe Fittings (B-303) >= 10" CLD 23 MLTPL
Concrete Pressure Pipe Fittings (B303) >= 10" CLD 23 MLTPL
Concrete Pressure Pipe Fittings (BWP) >= 10" CLD 23 MLTPL
Concrete Pressure Pipe Fittings (C300) >= 10" CLD 23 MLTPL
Concrete Pressure Pipe Fittings (C303) >= 10" CLD 23 MLTPL
Concrete Pressure Pipe Fittings (E) >= 10" CLD 23 MLTPL
Concrete Pressure Pipe Fittings (E-301) >= 10" CLD 23 MLTPL
Concrete Pressure Pipe Fittings (E301) >= 10" CLD 23 MLTPL
Concrete Pressure Pipe Fittings (ECP) >= 10" CLD 23 MLTPL
Concrete Pressure Pipe Fittings (L) >= 10" CLD 23 MLTPL
Concrete Pressure Pipe Fittings (L-301) >= 10" CLD 23 MLTPL
Concrete Pressure Pipe Fittings (L301) >= 10" CLD 23 MLTPL
Concrete Pressure Pipe Fittings (LCP) >= 10" CLD 23 MLTPL
Pressure Pipe Tapping Saddles[3] >= 1/2" CLD 23 MLTPL
Steel Fitting, Mortar Lined >= 10" CLD 23 MLTPL
Steel Fitting, Mortar Lined (S-200) >= 10" CLD 23 MLTPL
Steel Fitting, Mortar Lined (S200) >= 10" CLD 23 MLTPL
Steel Fitting, Mortar Lined (WSP) >= 10" CLD 23 MLTPL

[3] This product's evaluation was based on use of NSF Standard 61 Certified Gaskets and
    Coatings.

Pipe[1] [2]
Bar Wrapped Concrete Cylinder Pipe (XX-B) >= 10" CLD 23 MLTPL
Bar Wrapped Concrete Cylinder Pipe (B-303) >= 10" CLD 23 MLTPL
Bar Wrapped Concrete Cylinder Pipe (BWP) >= 10" CLD 23 MLTPL
Bar Wrapped Concrete Cylinder Pipe (C303) >= 10" CLD 23 MLTPL
Prestressed Concrete Cylinder Pipe (C300) >= 16" CLD 23 MLTPL
Prestressed Concrete Cylinder Pipe (E-301) >= 16" CLD 23 MLTPL
Prestressed Concrete Cylinder Pipe (E301) >= 16" CLD 23 MLTPL
Prestressed Concrete Cylinder Pipe (ECP) >= 16" CLD 23 MLTPL
Prestressed Concrete Cylinder Pipe (L-301) >= 16" CLD 23 MLTPL
Prestressed Concrete Cylinder Pipe (L301) >= 16" CLD 23 MLTPL
Prestressed Concrete Cylinder Pipe (LCP) >= 16" CLD 23 MLTPL
Prestressed Concrete Cylinder Pipe (XX-E or XX-L) >= 16" CLD 23 MLTPL
Steel Pipe, Mortar Lined (S-200) >= 10" CLD 23 MLTPL
Steel Pipe, Mortar Lined (S200) >= 10" CLD 23 MLTPL
Steel Pipe, Mortar Lined (WSP) >= 10" CLD 23 MLTPL
Steel Pipe, Mortar Lined (XX-S) >= 10" CLD 23 MLTPL

[1] Certification includes authorized gaskets and lubricant.
[2] XX represents a 2- or 3- digit pipe diameter.



 
Thordon Bearings, Inc. 
3225 Mainway Drive
Burlington, ON L7M 1A6 
Canada 
905-335-1440
Visit this company's website


Facility : Burlington, Ontario, Canada

Mechanical Devices

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Miscellaneous Process Devices/Components
ThorPlas-White[1] 1" x 1" - 12" x 20" CLD 23 TPES

[1] ThorPlas-White bearings are intended for use with water pumps.



 
Thorinox Inc. 
3590 Arthur Villeneuve
Saint-Laurent, QC H4R 3K8 
Canada 
514-382-3620
Visit this company's website


Facility : # 1 China

Mechanical Plumbing Devices

Trade Designation      

Commercial Faucets[G]
98-A      
98-HSX[1]      
98-SW      
98-SW      
9816-X[1]      
DM-04-X[1]      
DM-08-X[1]      
DM-100-55[1]      
DM-100-68      
DM-200-S12      
DM-200-S8      
WM-04-X[1]      
WM-08-G6      
WM-08-S12      
WM-08-X[1]      
WM-100-55      
WM-200-68      
WM-200-S12      
WM-200-S8      
WM-50-X[1]      
WM-60-X[1]      

[1] X - 06/08/10/12/14/16/18 (for swing spout); designates length of spout in inches
    X - P1/P2/P3/P4/P5/P6 (for gooseneck spout)

[G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for
    “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state
    laws and the U.S. Safe Drinking Water Act.

    



 
Tianjin Dongyi Magnesium Products Co., LTD 
No.26 Fufa Road
Jing-jin Technology Valley 
Wuqing District, Tianjin 301700 
China 
86 22 59621606


Facility : Tianjin, China

Mechanical Devices

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Sacrificial Anodes[G]
221954 REV A 5 gal. - 300 gal. C. HOT MLTPL
222030 REV C 5 gal. - 300 gal. C. HOT MLTPL
222031 REV D 5 gal. - 300 gal. C. HOT MLTPL
222032 REV 5 gal. - 300 gal. C. HOT MLTPL
222033 REV D 5 gal. - 300 gal. C. HOT MLTPL
FAW-00983-AZ31B-019.375-S3 5 gal. - 300 gal. C. HOT MLTPL
FAW-00983-AZ31B-022.375-S3 5 gal. - 300 gal. C. HOT MLTPL
FAW-00983-AZ31B-025.375-S3 5 gal. - 300 gal. C. HOT MLTPL
FAW-00983-AZ31B-030.375-S3 5 gal. - 300 gal. C. HOT MLTPL
FAW-00983-AZ31B-039.375-S3 5 gal. - 300 gal. C. HOT MLTPL
FAW-00983-AZ31B-044.375-S3 5 gal. - 300 gal. C. HOT MLTPL
FAW-00983-AZ31B-050.375-S3 5 gal. - 300 gal. C. HOT MLTPL
FAW-00983-AZ31B-053.375-S3 5 gal. - 300 gal. C. HOT MLTPL
FAW-00983-AZ31B-056.375-S3 5 gal. - 300 gal. C. HOT MLTPL
FAW-01070-AZ31B-010.375-S2 5 gal. - 300 gal. C. HOT MLTPL
FAW-01070-AZ31B-011.375-S2 5 gal. - 300 gal. C. HOT MLTPL
FAW-01070-AZ31B-013.375-S2 5 gal. - 300 gal. C. HOT MLTPL
FAW-01070-AZ31B-015.375-S2 5 gal. - 300 gal. C. HOT MLTPL
FAW-01070-AZ31B-019.375-S2 5 gal. - 300 gal. C. HOT MLTPL
FAW-01070-AZ31B-024.375-S2 5 gal. - 300 gal. C. HOT MLTPL
FAW-01070-AZ31B-025.375-S2 5 gal. - 300 gal. C. HOT MLTPL
FAW-01070-AZ31B-030.375-S2 5 gal. - 300 gal. C. HOT MLTPL
FAW-01070-AZ31B-034.375-S2 5 gal. - 300 gal. C. HOT MLTPL
FAW-01070-AZ31B-039.375-S2 5 gal. - 300 gal. C. HOT MLTPL
FAW-01070-AZ31B-050.375-S2 5 gal. - 300 gal. C. HOT MLTPL
FAW-01070-AZ31B-053.375-S2 5 gal. - 300 gal. C. HOT MLTPL
FAW-04400-AZ31B-011.375-S1-RM 5 gal. - 300 gal. C. HOT MLTPL
FAW-04400-AZ31B-015.375-S1-RM 5 gal. - 300 gal. C. HOT MLTPL
FAW-04400-AZ31B-019.375-S1-RM 5 gal. - 300 gal. C. HOT MLTPL
FAW-04400-AZ31B-024.375-S1-RM 5 gal. - 300 gal. C. HOT MLTPL
FAW-04400-AZ31B-025.375-S1-RM 5 gal. - 300 gal. C. HOT MLTPL
FAW-04400-AZ31B-030.375-S1-RM 5 gal. - 300 gal. C. HOT MLTPL
FAW-04400-AZ31B-034.375-S1-RM 5 gal. - 300 gal. C. HOT MLTPL
FAW-04400-AZ31B-039.375-S1-RM 5 gal. - 300 gal. C. HOT MLTPL
FAW-04400-AZ31B-044.375-S1-RM 5 gal. - 300 gal. C. HOT MLTPL
FAW-04400-AZ31B-050.375-S1-RM 5 gal. - 300 gal. C. HOT MLTPL
FAW-06826-AZ31B-022.375-S3 5 gal. - 300 gal. C. HOT MLTPL
FAW-06826-AZ31B-024.375-S3 5 gal. - 300 gal. C. HOT MLTPL
FAW-06826-AZ31B-025.375-S3 5 gal. - 300 gal. C. HOT MLTPL
FAW-06826-AZ31B-034.375-S3 5 gal. - 300 gal. C. HOT MLTPL
FAW-06826-AZ31B-039.375-S3 5 gal. - 300 gal. C. HOT MLTPL
FAW-06826-AZ31B-042.375-S3 5 gal. - 300 gal. C. HOT MLTPL
FAW-06826-AZ31B-044.375-S3 5 gal. - 300 gal. C. HOT MLTPL
FAW-06826-AZ31B-048.375-S3 5 gal. - 300 gal. C. HOT MLTPL
FAW-06826-AZ31B-050.375-S3 5 gal. - 300 gal. C. HOT MLTPL
FAW-06826-AZ31B-053.375-S3 5 gal. - 300 gal. C. HOT MLTPL

[G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for
    “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state
    laws and the U.S. Safe Drinking Water Act.

    



 
Tianjin FSK Flow Control Equipment Co., Ltd. 
No. 5, Keda 3rd Road
TEDA Technic Park, Jinnan District 
Tianjin 300350 
China 
86 16622383527
Visit this company's website


Facility : Tianjin, China

Mechanical Devices

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Valves [G]
AWWA C504 Butterfly Valve 3" - 72" CLD 23 MLTPL
AWWA C509 GateValve[1] 3" - 48" CLD 23 MLTPL
Series GV2 Resilient Seated Gate Valve 3" - 48" CLD 23 MLTPL

[1] Certified for use in distribution systems only.
[G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for
    “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state
    laws and the U.S. Safe Drinking Water Act.

    



 
Tianjin Galaxy Valve Co., Ltd. 
No. 15 Tianhua Road
Balitai Industrial Area 
Tianjin 300350 
China 
86 133 3202 7165


Facility : Tianjin, China

Mechanical Devices

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Strainer[G]
Y-Strainers-7001 2" - 24" CLD 23 MLTPL

[G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for
    “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state
    laws and the U.S. Safe Drinking Water Act.

    

Valves[G]
322A- NRS Resilient-seated Gate Valves With Wrench Nut 2" - 24" CLD 23 MLTPL
322B-NRS Resilient-seated Gate Valves With Handwheel 2" - 24" CLD 23 MLTPL
Center Line-Type Butterfly Valve-2302A 2" - 24" CLD 23 MLTPL
Center Line-Type Butterfly Valve-2302V 2" - 24" CLD 23 MLTPL
Center Line-Type Butterfly Valve-2502A 2" - 24" CLD 23 MLTPL
Center Line-Type Butterfly Valve-2502V 2" - 24" CLD 23 MLTPL
Double Eccentric Rubber Sealing Flange Butterfly Valve 2630 8" - 48" CLD 23 MLTPL
Double flange Butterfly Valve-2102 2" - 24" CLD 23 MLTPL
Dual-plate Wafer Check Valve-5307 2" - 24" CLD 23 MLTPL
NRS Resilient-seated Gate Valves 322 2" - 24" CLD 23 MLTPL
OS&Y Resilient-Seated Gate Valves 333 2" - 24" CLD 23 MLTPL

[G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for
    “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state
    laws and the U.S. Safe Drinking Water Act.

    



 
Tianjin Hongrui Rubber Co., Ltd 
Beizhakou Development Zone
Jinnan District 
Tianjin 300350 
China 
86 22 88511898
Visit this company's website


Facility : Tianjin, China

Mechanical Devices

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Gasket/Sealing Materials
EPDM-TJHR 1" - 120" CLD 23 EPDM

[1] Certified for use as a valve seat 1"- 120".


 
Tianjin Huilitong Steel Tube Co., Ltd. 
North Loop Industrial Park, Economic and
Technological Development zone 
Jinghai County, Tianjin 
China 
86 153 0213 8079
Visit this company's website


Facility : Tianjin, China

Pipes and Related Products

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Pipe[G]
SAWH CARBON STEEL PIPES 8" - 100" D. HOT CS

[G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for
    “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state
    laws and the U.S. Safe Drinking Water Act.

    



 
Tianjin Junxing Pipe Group Co., Ltd. 
No.1, Kaiyuan Road, Fuyuan Economic
Development Zone, Meichang Town 
Wuqing, Tianjin 301700 
China 
86 228 478 3371 
86 156 5791 4318


Facility : Wuqing, Tianjin, China

Pipes and Related Products

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Fittings[G]
JUNXING PP-R Cross 20 mm - 25 mm C. HOT PP
JUNXING PP-R Cross Fitting 20 mm - 32 mm C. HOT PP
JUNXING PP-R End Cap 20 mm - 200 mm C. HOT PP
JUNXING PP-R Equal Coupling 20 mm - 200 mm C. HOT PP
JUNXING PP-R Equal Elbow 45 20 mm - 200 mm C. HOT PP
JUNXING PP-R Equal Elbow 90 20 mm - 200 mm C. HOT PP
JUNXING PP-R Equal Tee 20 mm - 200 mm C. HOT PP
JUNXING PP-R Flange Adaptor 50 mm - 200 mm C. HOT PP
JUNXING PP-R Over Bend 20 mm - 32 mm C. HOT PP
JUNXING PP-R Reducing Coupling 25x20 - 200x160 mm C. HOT PP
JUNXING PP-R Reducing Elbow 90 25x20 - 63x50 mm C. HOT PP
JUNXING PP-R Reducing Large Tee 20x25x20-25x32x25 mm C. HOT PP
JUNXING PP-R Reducing Tee 25x20 - 200x160 mm C. HOT PP

[G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for
    “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state
    laws and the U.S. Safe Drinking Water Act.

    

Pipe[G]
JUNXING PP-R Pipe S2.5 SDR6 PN20 20 mm - 200 mm C. HOT PP
JUNXING PP-R Pipe S3.2 SDR7.4 PN16 20 mm - 200 mm C. HOT PP
JUNXING PP-R Pipe S4 SDR9 PN12.5 20 mm - 200 mm C. HOT PP
JUNXING PP-R Pipe S5 SDR11 PN10 20 mm - 200 mm C. HOT PP

[G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for
    “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state
    laws and the U.S. Safe Drinking Water Act.

    



 
Tianjin Kailida Control Technology Development Co., Ltd. 
JinPing Road #10
Nankai Industrial Park, NanKai District 
Tianjin 300190 
China 
86 22 2763 1233


Facility : Tianjin, China

Mechanical Devices

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Valves[1] [G]
DN10 KLD Ball Valve 10 mm CLD 23 MLTPL
DN15 KLD Ball Valve 15 mm CLD 23 MLTPL
DN20 KLD Ball Valve 20 mm CLD 23 MLTPL
DN20-15 KLD Ball Valve 20 mm x 15 mm CLD 23 MLTPL
DN25 KLD Ball Valve 25 mm CLD 23 MLTPL
DN25-20 KLD Ball Valve 25 mm x 20 mm CLD 23 MLTPL
DN32 KLD Ball Valve 32 mm CLD 23 MLTPL
DN40 KLD Ball Valve 40 mm CLD 23 MLTPL
DN50 KLD Ball Valve 50 mm CLD 23 MLTPL
DN8 KLD Ball Valve 8 mm CLD 23 MLTPL

[1] Certified for stainless steel valves only.
[G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for
    “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state
    laws and the U.S. Safe Drinking Water Act.

    



 
Tianjin Motimo Membrane Technology Ltd. 
No. 60, 11th Street, Teda
Tianjin 300457 
China 
86 22 66230233
Visit this company's website


Facility : Tianjin, China

Mechanical Devices

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Filtration Devices/Components[1]
MOF-IIb[2] [3] 80 mm x 650 mm CLD 23 MLTPL

[1] Only products bearing the NSF Mark on the product, product packaging, and/or
    documentation shipped with the product are Certified.
[2] Certified for a minimum of 1,550 L/day.
[3] Product requires a preservice flush of 200-400 L/hr for 3 hrs at 0.1MPa.

Ultrafiltration Devices[1] [4] [5] [6]
SF-6** 190 x 1693 mm CLD 23 MLTPL
ST-6** 190 x 1693 mm CLD 23 MLTPL

[1] Only products bearing the NSF Mark on the product, product packaging, and/or
    documentation shipped with the product are Certified.
[4] Certified for a minimum daily flow of 29,400 liters.
[5] Procedure for flushing preservative prior to use: 
    
    1. Surface Flushing: flush directly with water for 15 to 30 minutes or soak in a water
    for 1 to 2 hours, changing the water every 30 minutes.
     
    2. Internal flushing: Soak in a water sink for 72 hours, change the water every 12 hours.
[6] ** refers to the number of fibers and may be any number from 35-60.



 
Tianjin Tian Gong New Material Technology Co., Ltd. 
No. 4 Taijin Road
Zhangjiawo Industrial Zone 
Xiqing, Tianjin 300380 
China 
86 22 8399 0331
Visit this company's website


Facility : Tianjin, China

Mechanical Devices

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Reverse Osmosis Element[1] [2] [3]
BW-4040 4" x 40" CLD 23 MLTPL
BW-8040 8" x 40" CLD 23 MLTPL
BW-8040-400 8" x 40" CLD 23 MLTPL
BW30-400 8" x 40" CLD 23 MLTPL
BW30FR-400/34 8" x 40" CLD 23 MLTPL
FR-4040 4" x 40" CLD 23 MLTPL
FR-8040 8" x 40" CLD 23 MLTPL
FR-8040-365/36 8" x 40" CLD 23 MLTPL
FR-8040-400/34 8" x 40" CLD 23 MLTPL
LE-2521 2 1/2" x 21" CLD 23 MLTPL
LE-2540 2 1/2" x 40" CLD 23 MLTPL
LE-4021 4" x 21" CLD 23 MLTPL
LE-4040 4" x 40" CLD 23 MLTPL
LE-4040-HF 4" x 40" CLD 23 MLTPL
LE-4040-HR 4" x 40" CLD 23 MLTPL
LE-8040 8" x 40" CLD 23 MLTPL
LE-8040-400 8" x 40" CLD 23 MLTPL
NF-4040 4" x 40" CLD 23 MLTPL
NF-4040-30 4" x 40" CLD 23 MLTPL
NF-4040-90 4" x 40" CLD 23 MLTPL
NF-8040 8" x 40" CLD 23 MLTPL
NF-8040-30 8" x 40" CLD 23 MLTPL
NF-8040-90 8" x 40" CLD 23 MLTPL
SW-2521 2 1/2" x 21" CLD 23 MLTPL
SW-2540 2 1/2" x 40" CLD 23 MLTPL
SW-4021 4" x 21" CLD 23 MLTPL
SW-4040 4" x 40" CLD 23 MLTPL
SW-8040 8" x 40" CLD 23 MLTPL

[1] LE-2521 and SW-2521 models are flushed at a flow rate of 6.2 gallons per minute for 90
    minutes with DI water.
    SW-2540 and LE-2540 models are flushed at a flow rate of 6.5 gallons per minute for 90
    minutes with DI water.
    SW-4021 and LE-4021 models are flushed at a flow rate of 6.9 gallons per minute for 90
    minutes with DI water.
    LE-4040-HF is flushed at a flow rate of 7.7 gallons per minute for 90 minutes with DI
    water.
    BW-4040 and FR-4040 models are flushed at a flow rate of 7.8 gallons per minute for 90
    minutes with DI water.
    LE-4040-HR is flushed at a flow rate of 7.9 gallons per minute for 90 minutes with DI
    water.
    SW-4040 is flushed at a flow rate of 8 gallons per minute for 90 minutes with DI water.
    LE-4040 is flushed at a flow rate of 8.1 gallons per minute for 90 minutes with DI
    water.
    BW30-400 is flushed at a flow rate of 8.2 gallons per minute for 90 minutes with DI
    water.
    NF-4040-30, BW30FR-400/34 and NF-4040 models are flushed at a flow rate of 8.3 gallons
    per minute for 90 minutes with DI water.
    NF-4040-90 is flushed at a flow rate of 8.4 gallons per minute for 90 minutes with DI
    water.
    FR-8040 is flushed at a flow rate of 10 gallons per minute for 90 minutes with DI water.
    FR-8040-365/36 is flushed at a flow rate of 10.2 gallons per minute for 90 minutes with
    DI water.
    FR-8040-400/34 and SW-8040 models are flushed at a flow rate of 10.3 gallons per minute
    for 90 minutes with DI water.
    BW-8040-400, NF-8040-30 and NF-8040-90 models are flushed at a flow rate of 10.5 gallons
    per minute for 90 minutes with DI water.
    BW-8040 and LE-8040-400 models are flushed at a flow rate of 10.8 gallons per minute for
    90 minutes with DI water.
    LE-8040 and NF-8040 models are flushed at a flow rate of 10.9 gallons per minute for 90
    minutes with DI water.
[2] LE-2521 and SW-2521 models are Certified to a minimum daily flow of 288 gallons per day.
    LE-2540 is Certified for a minimum daily flow of 760 gallons per day.
    SW-2540 is Certified for a minimum daily flow of 770 gallons per day.
    SW-4021 is Certified for a minimum daily flow of 1160 gallons per day.
    LE-4021 is Certified for minimum daily flow of 1200 gallons per day.
    FR-4040 is Certified for a minimum daily flow of 2200 gallons per day.
    BW-4040 is Certified for a minimum daily flow of 2400 gallons per day.
    LE-4040-HR, LE-4040 and NF-4040-30 models are Certified for a minimum daily flow of 2800
    gallons per day.
    SW-4040 and NF-4040-90 models are Certified for a minimum daily flow of 2900 gallons per
    day.
    NF-4040 is Certified for a minimum daily flow of 3000 gallons per day.
    LE-4040-HF is Certified for a minimum daily flow of 3300 gallons per day.
    FR-8040-365/36 is Certified for a minimum daily flow of 9500 gallons per day.
    BW-8040 and FR-8040-400/34 models are Certified for a minimum daily flow of 10000
    gallons per day.
    FR-8040 is Certified for a minimum daily flow of 10080 gallons per day.
    NF-8040-30 is Certified for a minimum daily flow of 10300 gallons per day.
    NF-8040-90 is Certified for a minimum daily flow of 10400 gallons per day.
    BW-8040-400 and BW30-400 are Certified for a minimum daily flow of 10600 gallons per
    day.
    BW30FR-400/34 is Certified for a minimum daily flow of 10800 gallons per day.
    LE-8040 is Certified for a minimum daily flow of 11000 gallons per day.
    NF-8040 is Certified for a minimum daily flow of 11600 gallons per day.
    LE-8040-400 is Certified for a minimum daily flow of 12500 gallons per day.
    SW-8040 is Certified for a minimum daily flow of 13300 gallons per day.
[3] Abbreviations at the beginning of the trade names indicate the following:
    SW - Seawater
    LE - Low Pressure
    BW - Brackish Water
    FR - Anti-Pollution
    NF - High Output



 
TIGG, LLC 
1555 Coraopolis Heights Road
Coraopolis, PA 15108 
United States 
800-925-0011 
723-703-3020
Visit this company's website


Facility : Heber Springs, AR

Mechanical Devices

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Miscellaneous Treatment Devices/Components[1] [G]
CP10K-8[2] 6" CLD 23 MLTPL
CP20K-10[3] 8" CLD 23 MLTPL
CP20K-12[3] 8" CLD 23 MLTPL
CP40K-12[4] 8" CLD 23 MLTPL

[1] Each model may come in a single tank or dual tank configuration.  These models are
    certified without carbon therefore no flushing is required.
[2] The CP10K-8 model is certified for a minimum daily flow of 72,000 gallons per day (50
    gallons per minute)
[3] The CP20K10 and CP20K-12 models are certified for a minimum daily flow of 112,320
    gallons per day (78 gallons per minute).
[4] The CP40K-12 model is certified for a minimum daily flow of 162,720 gallons per day (113
    gallons per minute).
[G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for
    “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state
    laws and the U.S. Safe Drinking Water Act.

    



 
Tigre Colombia S.A.S. 
KM 1.5 Vía Sibéria – Cota
Condomínio Empresarial Potrero Chico 
Parque Industrial Robles II Bodega 7 y 8 
Colombia 
55 47441 5000
Visit this company's website


Facility : Cota, Colombia

Pipes and Related Products

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Fittings
45 Elbow S x S 1/2" - 4" CLD 23 PVC
90 Elbow S x FIPT 1/2" - 4" CLD 23 PVC
90 Elbow S x S 1/2" - 4" CLD 23 PVC
Cap FITP 1/2" - 4" CLD 23 PVC
Cap S 1/2" - 4" CLD 23 PVC
Coupling S x S 1/2" - 4" CLD 23 PVC
Female Adapter S x FIPT 1/2" - 4" CLD 23 PVC
Male Adapter S x MIPT 1/2" - 4" CLD 23 PVC
Reducer Bushing SPG x FIPT 1/2" - 4" CLD 23 PVC
Reducer Bushing SPG x S 1/2" - 4" CLD 23 PVC
Reducer Tee S x S x S 1/2" - 4" CLD 23 PVC
Tee S x S x S 1/2" - 4" CLD 23 PVC
Tee S x S x Thread 1/2" - 4" CLD 23 PVC



 
Tigre USA 
533 East Third Street
P.O. Box 2097 
Beaumont, CA 92223 
United States 
951-845-3161
Visit this company's website


Facility : Beaumont, CA

Pipes and Related Products

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Fittings[G]
Dura CTS01-005 - Tee 1/2" C. HOT CPVC
Dura CTS01-007 - Tee 3/4" C. HOT CPVC
Dura CTS01-010 - Tee 1' C. HOT CPVC
Dura CTS01-020 - Tee 2" x 2" x 2" C. HOT CPVC
Dura CTS01-074 - Tee 1/2" x 1/2" x 3/4" C. HOT CPVC
Dura CTS01-094 - Tee 3/4" x 1/2" x 1/2" C. HOT CPVC
Dura CTS01-095 - Tee 3/4" x 1/2" x 3/4" C. HOT CPVC
Dura CTS01-101 - Tee 3/4" x 3/4" x 1/2" C. HOT CPVC
Dura CTS01-130 - Tee 1" x 1" x 1/2" C. HOT CPVC
Dura CTS01-131 - Tee 1" x 1" x 3/4" C. HOT CPVC
Dura CTS06-005 - 90 ° Elbow 1/2" C. HOT CPVC
Dura CTS06-007 - 90 ° Elbow 3/4" C. HOT CPVC
Dura CTS06-010 - 90 ° Elbow 1" C. HOT CPVC
Dura CTS09-005 - 90 ° Street Elbow 1/2" C. HOT CPVC
Dura CTS09-007 - 90 ° Street Elbow 3/4" C. HOT CPVC
Dura CTS17-005 - 45 ° Elbow 1/2" C. HOT CPVC
Dura CTS17-007 - 45 ° Elbow 3/4" C. HOT CPVC
Dura CTS17-010 - 45 ° Elbow 1" C. HOT CPVC
Dura CTS26-005 - Drop Ear Elbow 1/2" C. HOT CPVC
Dura CTS29-005 - Coupling 1/2" C. HOT CPVC
Dura CTS29-007 - Coupling 3/4" C. HOT CPVC
Dura CTS29-010 - Coupling 1" C. HOT CPVC
Dura CTS29-101 - Reducing Coupling 3/4" x 1/2" C. HOT CPVC
Dura CTS35-005 - Female Adapter 1/2" C. HOT CPVC
Dura CTS35-007 - Female Adapter 3/4" C. HOT CPVC
Dura CTS35-010 - Female Adapter 1" C. HOT CPVC
Dura CTS36-005 - Male Adapter 1/2" C. HOT CPVC
Dura CTS36-007 - Male Adapter 3/4" C. HOT CPVC
Dura CTS36-010 - Male Adapter 1" C. HOT CPVC
Dura CTS37-101 - Reducer Bushing 3/4" x 1/2" C. HOT CPVC
Dura CTS47-005 - Cap 1/2" C. HOT CPVC
Dura CTS47-007 - Cap 3/4" C. HOT CPVC
Dura CTS47-010 - Cap 1" C. HOT CPVC

[G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for
    “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state
    laws and the U.S. Safe Drinking Water Act.

    



 
TIPCO Technologies, Inc. 
11412 Cronhill Drive
Owings Mills, MD 21117 
United States 
410-356-0003
Visit this company's website


Facility : Glen Burnie, MD

Joining and Sealing Materials

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Gasket/Sealing Materials
American Biltrite EPDM[1] [G] [2] C. HOT EPDM
Garlock Multi-swell 3760[G] [3] CLD 23 OTHER
Teadit NA1082SAN [4] CLD 23 NBR

[1] This product has also been evaluated for use in Mechanical Plumbing Device applications
    with a maximum use restriction of 0.2 square inches/L.
[2] Certified for a maximum surface area to volume ratio of 2.0 square inches/L.
[3] Certified for a maximum width of 1/8” when used with pipes 1'' - 144'' in diameter.
[4] Certified for a maximum surface area to volume ratio of 1.1 square inches/L.
[G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for
    “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state
    laws and the U.S. Safe Drinking Water Act.

    

O-Rings
American Biltrite EPDM[1] [G] [2] C. HOT EPDM
Teadit NA1082SAN [4] CLD 23 NBR

[1] This product has also been evaluated for use in Mechanical Plumbing Device applications
    with a maximum use restriction of 0.2 square inches/L.
[2] Certified for a maximum surface area to volume ratio of 2.0 square inches/L.
[4] Certified for a maximum surface area to volume ratio of 1.1 square inches/L.
[G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for
    “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state
    laws and the U.S. Safe Drinking Water Act.

    



 
Tisan Mühendislik Plastikleri San. Tic. Ltd. Sti. 
Eksioglu Mah.
Yavuz Selim Cad. 86. Sk. No:4 
34794 Cekmeköy, Istanbul 
Türkiye 
90 216 429 3665
Visit this company's website


Facility : Istanbul, Turkey

Potable Water Materials

    Water Water
    Contact Contact
Trade Designation End Use Temp Material

Potable Water Materials[1]
TISLAMID 6 GF 20 UV HS BK A,F,P CLD 23 RNP
TISLAMID 6 GF 25 UV HS BK A,F,P CLD 23 RNP
TISLAMID 6 GF 30 UV HS BK A,F,P CLD 23 RNP
TISLAMID 6 GF 33 UV HS BK A,F,P CLD 23 RNP
TISLAMID 6 GF 45 UV HS BK A,F,P CLD 23 RNP
TISLAMID 6 GF 50 UV HS BK A,F,P CLD 23 RNP
TISLAMID 6 GF 60 UV HS BK A,F,P CLD 23 RNP

[1] Pipe, fitting and appurtenance end use. Certified for a maximum surface area to volume
    ratio of 460 square inches/L.



 
Tnemec Company, Inc. 
6800 Corporate Drive
Kansas City, MO 64120-1372 
United States 
816-474-3400
Visit this company's website


Facility : Baltimore, MD

Protective (Barrier) Materials

    Water Water
  Water Contact Contact Contact
Trade Designation Size Restriction Temp Material

Coatings - Fittings
22 Epoxoline[1] [2] >= 1/2" CLD 23 EPOXY
N140F Pota-Pox Plus Fast Cure [2] [3] >= 2" CLD 23 EPOXY
Series 21 Epoxoline[2] [4] >= 1" CLD 23 EPOXY
Series 91-H2O ™ Hydro-Zinc™ [2] [6] [7] >= 1" CLD 23 EPOXY
Series 91-H2O ™ Hydro-Zinc™ [2] [5] [6] >= 1/2" CLD 23 EPOXY
Series 93-H20 Hydro-Zinc[8] >= 1" CLD 23 PUR
Series 94-H2O Hydro-Zinc[2] [9] [10] CLD 23 PUR
Series L140 Pota-Pox Plus [2] [11] >= 1" CLD 23 EPOXY
Series L140F Pota-Pox Plus Fast Cure [2] [12] >= 1" CLD 23 EPOXY
Series N140 Pota-Pox Plus[2] [13] >= 2" CLD 23 EPOXY
Series N140 Pota-Pox Plus[14] [15] >= 4" CLD 23 EPOXY
Series N140F Pota-Pox Plus Fast Cure[15] [16] >= 4" CLD 23 EPOXY

[1] Colors: 1255 Beige, 1218 Blue, WH11 White
    Number of Coats: 1-2
    Maximum Field Use Dry Film Thickness (in mils): 50
    Maximum Thinner: 5% Thinner #2
    Recoat Cure Time and Temperature: 16 hours at 75°F
    Final Cure Time and Temperature: 5 days at 75°F
    Special Comments: Mix ratio of Part A to Part B is 1:1 by volume.  Optional use with
    fiberglass flake S211-0220.  The fiberglass flake can be added up to a rate of 1% by
    weight after the Parts A and B are mixed together.  Certified for use as a primer or
    topcoat with any NSF Certified Tnemec coating system provided that both primer and
    topcoat meet their individual certified end uses.
[2] Meets the health effects requirements of NSF/ANSI/CAN 600 according to the requirements
    of NSF/ANSI/CAN 61 including the most current health effects criteria for xylenes,
    toluene, and ethylbenzene. 
[3] Colors: 15BL Tank White, 1255 Beige, 1211 Red, 35GR Black, 39BL Delft Blue, Y2606 Romac
    Yellow, 00WH Tnemec White, 11SF True Blue, B9118 Baker Blue, B5712 Westech Blue, B2592
    RAL 5009 Azurblau, B9695 Houston Blue, A14130 Mueller Gray, R5477 Mueller Sienna Red.
    Number of Coats: 1
    Sequence of Coats: 4 mils
    Maximum Thinner: 10% No. 4 Thinner by volume
    Recoat Cure Time and Temperature: 5 hours at 75F
    Final Cure Time/Temperature: 7 days at 75F (entire system)
    Special Comments: Mix ration is 1 Part A to 1 Part B by volume. Certified for use as an
    optional primer or intermediate topcoat with any Tnemec NSF certified primer and topcoat
    coating system provided the primer, intermediate, and topcoat meet their certified end
    uses. 
[4] Colors: WH16 OFF-WHITE, 35GR Black, 33GR Gray, 39BL Delft Blue, 1255 Beige, B5712
    Westech Blue, 11SF True Blue/Safety, 1211 Red Primer, A13096 Baker Dark Gray, B2592
    RAL5009 Azurblau, B2506 Dezurik Blue, B9918 New Baker Blue
    Number of Coats: 1-3
    Maximum Field Use Dry Thickness (in mils): 20
    Maximum Thinner: 5% F041-0088 Thinner Clear by volume
    Recoat Cure Time and Temperature: 8 hours at 75F
    Final Cure Time/Temperature: 7 days at 75F
    Special Comments: Mix ratio of A:B is 2:1 by volume. Series 21 Epoxoline is approved for
    use as a primer or topcoat with any NSF Certified Tnemec topcoat or coating system
    providing that both primer and topcoat meet their individual Certified end uses.
[5] This coating used with Thinner #3 is Certified for use in pipes >=24", tanks >=1500
    gallons, fittings >=1/2", pumps >=1/2", valves >=2".
[6] Colors: Greenish-Gray
    Number of Coats: 1
    Maximum Field Use Dry Thickness (in mils): 4
    Maximum Thinner: 10% Thinner #2 or Thinner #3 by volume
    Final Cure Time/Temperature: 4 hours at 75F; 2 hours at 75F wen accelerator is used. 
    Special Comments: Series 44-710 Urethane Accelerator may be added up to 4 fl.oz/gal.
    Series 91-H2O Hydro-Zinc ™ is approved for use with any NSF Certified Tnemec topcoat or
    coatings system providing that both primer and topcoat meet their individual Certified
    end uses. Mix Ratio Part A:B is 70%:30% by volume.
[7] This coating used with Thinner #2 is Certified for use in pipes >=24", tanks >=3000
    gallons, fittings >=1", pumps >=1/2", and valves >=4".
[8] Colors: Greenish-Gray
    Maximum Field Use Dry Thickness(in mils): 4 mils
    Maximum Thinner: 10% Thinner #2 by volume
    Final Cure Time/Temperature: 8 hours at 75F. 4 hours at 75F if accelerator is used. 
    Special Comments: Series 44-710 accelerator may be used up to 4 fluid oz/gal. 93-H20
    Hydro-Zinc is approved for use with any NSF Certified Tnemec topcoat or coating system
    providing that both primer and topcoat meet their individual Certified end uses.
[9] Colors: Greenish-gray
    Number of Coats: 1
    Maximum Field Use Dry Film Thickness (in mils): 4
    Maximum Thinner: 15% Tnemec No. 49 or 10% Thinner No. 2 or 10% Thinner No. 3 by volume
    Final Cure Time and Temperature: 8 hours at 75°F; 2 hours at 75°F when the accelerator
    is used 
    Special Comments: Series 44-710 Urethane Accelerator may be added up to 4 fl. oz/gal. 
    94-H2O is aproved for use with any NSF Certified Tnemec topcoat or coating system.
[10] This coating used with Thinner #49 is Certified for use in fittings >= 1/2". This
     coating used with Thinner #2 is Certified for use in fittings >= 1". This coatings used
     with Thinner #3 is Certified for use in fittings >= 1/2".
[11] Colors: 1255 Beige, 15BL Tank White, 1211 Red, 00WH White 
     # of coats: 2-3
     # Seq Of Coats: Any combination of listed colors
     Max Film Thickness: 18 (Maximum of 6 mils per coat)
     Max Thinner: 5% Tnemec No. 49 Thinner by volume
     Recoat Cure Time/ Temp.:  16 hours at 75° F 
     Final Cure Time/ Temp.: 7 days at 75° F 
     Special Comments: Series N140, N140F, V140, V140F, L140 and Series 22, FC22 may be
     substituted as a primer or topcoat for L140 provided that both primer and topcoat meet
     their individual Certified end uses.  Series 44-700 accelerator (Part C) may be added up
     to 4 fluid ounces per two mixed gallons of L140 Parts A and B.  Mix ratio of A:B is 1:1
     by volume.
[12] Colors: 1255 Beige, 15BL Tank White, 1211 Red, 00WH White 
     # of coats: 2-3
     # Seq Of Coats: Any combination of listed colors
     Max Film Thickness: 18 (Maximum of 6 mils per coat)
     Max Thinner: 5% Tnemec No. 49 Thinner by volume
     Recoat Cure Time/ Temp.:  16 hours at 75° F 
     Final Cure Time/ Temp.: 7 days at 75° F 
     Special Comments: Series N140, N140F, V140, V140F, L140 and Series 22, FC22 may be
     substituted as a primer or topcoat for L140F provided that both primer and topcoat meet
     their individual Certified end uses.  Mix ratio of Part A to Part B is 1:1 by volume.
[13] Colors: 00WH Tnemec White, 1211 Red, 1255 Beige, 15BL Tank white, 35GR Black, 39BL Delft
     blue, B5712 Westech Blue, 11SF True Blue, B9118 Baker Blue, B8314 Krausz Blue, Y2606
     Romac Yellow, B2592 RAL 5009 Azurblau, B7011 Crispin Blue, B2506 Dezurik Blue, A14130
     Mueller Gray, B9695 Houston Blue, R5477 Mueller Sienna Red.
     Number of Coats: 1
     Maximum Field Use Dry Thickness(in mils): 4 mils
     Maximum Thinner: 10% No. 4 Thinner by volume
     Recoat Cure Time and Temperature: 5 hours at 75°F
     Final Cure Time and Temperature: 7 days at 75°F (entire system)
     Special Comments: Mix ratio is 1 Part A to 1 Part B by volume. Certified for use as an
     optional primer or intermediate coat with any Tnemec NSF certified primer and topcoat
     coating system provided the primer, intermediate, and topcoat meet their certified end
     uses.
[14] Colors: 00WH Tnemec White, 1211 Red, 1255 Beige, 15BL Tank White, 35GR Black, 39BL Delft
     Blue, B5712 Westech Blue, 11SF True Blue, B9118 Baker Blue, B8314 Krausz Blue, A13096
     Baker Dark Gray, Y2606 Romac Yellow, B2592 RAL 5009 Azurblau, B7011 Crispin Blue, B2506
     Dezurik Blue, A14130 Mueller Gray, B9695 Houston Blue, R5477 Mueller Sienna Red.
     Number of Coats: 2-3
     Sequence of Coats: Any combination of Listed colors
     Maximum Field Use Dry Film Thickness (in mils): 18
     Maximum Thinner: 5% Tnemec No. 60 Thinner by volume
     Recoat Cure Time and Temperature: 5 hours at 75°F with accelerator, 9 hours at 75°F
     without accelerator
     Final Cure Time and Temperature: 30 days at 75°F
     Special Comments: Any Listed color of Series 22, FC22, or N140, may be substituted as a
     primer of topcoat for Series N140 Pota-Pox Plus provided that both primer and topcoat
     meet their individual Certified end uses.  The mix ratio of Part A:Part B is 1:1 by
     volume.  Part C (Series 44-700 Accelerator) is an optional additive to Part A in the
     field and may be added at up to 4 fluid ounces per 2 mixed gallons of parts A and B.
[15] Meets the health effects requirements of NSF/ANSI/CAN 600 according to requirements of
     NSF/ANSI/CAN 61 for pump, valve, and fitting end use.
[16] Colors: 00WH Tnemec White, 1211 Red, 1255 Beige, 15BL Tank white, 35GR Black, 39BL Delft
     Blue, B2506 DeZurik Blue, B5712 Westech Blue, 11SF True Blue, B9118 Baker Blue, B7896
     S-B Blue, Y2606 Romac Yellow, B2592 RAL 5009 Azurblau, B7011 Crispin Blue, B9695 Houston
     Blue, A14130 Mueller Gray, R5477 Mueller Sienna Red.
     Number of Coats: 2-3
     Sequence of Coats: Any combination of Listed colors
     Maximum Field Use Dry film Thickness (in mils): 18
     Maximum Thinner: 5% Tnemec No. 60 Thinner by volume
     Recoat Cure Time and Temperature: 5 hours at 75°F 
     Final Cure Time and Temperature: 30 days at 75°F
     Special Comments: Any listed color of series 22, FC22, or N140 may be substituted as a
     primer or topcoat for the Series N140 Pota-Pox Plus provided that both primer and
     topcoat meet their individual Certified end uses.  Mix ratio of Part A:Part B is 1:1 by
     volume.

Coatings - Mechanical Devices
22 Epoxoline [1] [2] [26] CLD 23 EPOXY
Series 21 Epoxoline[2] [4] [23] CLD 23 EPOXY
Series 91-H2O™ Hydro-Zinc™ [2] [5] [6] [7] [24] CLD 23 PUR
Series 93-H20 Hydro-Zinc[8] [27] CLD 23 PUR
Series 94-H2O Hydro Zinc [2] [9] [24] [25] CLD 23 PUR
Series N140 Pota-Pox Plus[14] [15] [22] CLD 23 EPOXY
Series N140F Pota-Pox Plus Fast Cure[15] [16] [22] CLD 23 EPOXY

[1] Colors: 1255 Beige, 1218 Blue, WH11 White
    Number of Coats: 1-2
    Maximum Field Use Dry Film Thickness (in mils): 50
    Maximum Thinner: 5% Thinner #2
    Recoat Cure Time and Temperature: 16 hours at 75°F
    Final Cure Time and Temperature: 5 days at 75°F
    Special Comments: Mix ratio of Part A to Part B is 1:1 by volume.  Optional use with
    fiberglass flake S211-0220.  The fiberglass flake can be added up to a rate of 1% by
    weight after the Parts A and B are mixed together.  Certified for use as a primer or
    topcoat with any NSF Certified Tnemec coating system provided that both primer and
    topcoat meet their individual certified end uses.
[2] Meets the health effects requirements of NSF/ANSI/CAN 600 according to the requirements
    of NSF/ANSI/CAN 61 including the most current health effects criteria for xylenes,
    toluene, and ethylbenzene. 
[4] Colors: WH16 OFF-WHITE, 35GR Black, 33GR Gray, 39BL Delft Blue, 1255 Beige, B5712
    Westech Blue, 11SF True Blue/Safety, 1211 Red Primer, A13096 Baker Dark Gray, B2592
    RAL5009 Azurblau, B2506 Dezurik Blue, B9918 New Baker Blue
    Number of Coats: 1-3
    Maximum Field Use Dry Thickness (in mils): 20
    Maximum Thinner: 5% F041-0088 Thinner Clear by volume
    Recoat Cure Time and Temperature: 8 hours at 75F
    Final Cure Time/Temperature: 7 days at 75F
    Special Comments: Mix ratio of A:B is 2:1 by volume. Series 21 Epoxoline is approved for
    use as a primer or topcoat with any NSF Certified Tnemec topcoat or coating system
    providing that both primer and topcoat meet their individual Certified end uses.
[5] This coating used with Thinner #3 is Certified for use in pipes >=24", tanks >=1500
    gallons, fittings >=1/2", pumps >=1/2", valves >=2".
[6] Colors: Greenish-Gray
    Number of Coats: 1
    Maximum Field Use Dry Thickness (in mils): 4
    Maximum Thinner: 10% Thinner #2 or Thinner #3 by volume
    Final Cure Time/Temperature: 4 hours at 75F; 2 hours at 75F wen accelerator is used. 
    Special Comments: Series 44-710 Urethane Accelerator may be added up to 4 fl.oz/gal.
    Series 91-H2O Hydro-Zinc ™ is approved for use with any NSF Certified Tnemec topcoat or
    coatings system providing that both primer and topcoat meet their individual Certified
    end uses. Mix Ratio Part A:B is 70%:30% by volume.
[7] This coating used with Thinner #2 is Certified for use in pipes >=24", tanks >=3000
    gallons, fittings >=1", pumps >=1/2", and valves >=4".
[8] Colors: Greenish-Gray
    Maximum Field Use Dry Thickness(in mils): 4 mils
    Maximum Thinner: 10% Thinner #2 by volume
    Final Cure Time/Temperature: 8 hours at 75F. 4 hours at 75F if accelerator is used. 
    Special Comments: Series 44-710 accelerator may be used up to 4 fluid oz/gal. 93-H20
    Hydro-Zinc is approved for use with any NSF Certified Tnemec topcoat or coating system
    providing that both primer and topcoat meet their individual Certified end uses.
[9] Colors: Greenish-gray
    Number of Coats: 1
    Maximum Field Use Dry Film Thickness (in mils): 4
    Maximum Thinner: 15% Tnemec No. 49 or 10% Thinner No. 2 or 10% Thinner No. 3 by volume
    Final Cure Time and Temperature: 8 hours at 75°F; 2 hours at 75°F when the accelerator
    is used 
    Special Comments: Series 44-710 Urethane Accelerator may be added up to 4 fl. oz/gal. 
    94-H2O is aproved for use with any NSF Certified Tnemec topcoat or coating system.
[14] Colors: 00WH Tnemec White, 1211 Red, 1255 Beige, 15BL Tank White, 35GR Black, 39BL Delft
     Blue, B5712 Westech Blue, 11SF True Blue, B9118 Baker Blue, B8314 Krausz Blue, A13096
     Baker Dark Gray, Y2606 Romac Yellow, B2592 RAL 5009 Azurblau, B7011 Crispin Blue, B2506
     Dezurik Blue, A14130 Mueller Gray, B9695 Houston Blue, R5477 Mueller Sienna Red.
     Number of Coats: 2-3
     Sequence of Coats: Any combination of Listed colors
     Maximum Field Use Dry Film Thickness (in mils): 18
     Maximum Thinner: 5% Tnemec No. 60 Thinner by volume
     Recoat Cure Time and Temperature: 5 hours at 75°F with accelerator, 9 hours at 75°F
     without accelerator
     Final Cure Time and Temperature: 30 days at 75°F
     Special Comments: Any Listed color of Series 22, FC22, or N140, may be substituted as a
     primer of topcoat for Series N140 Pota-Pox Plus provided that both primer and topcoat
     meet their individual Certified end uses.  The mix ratio of Part A:Part B is 1:1 by
     volume.  Part C (Series 44-700 Accelerator) is an optional additive to Part A in the
     field and may be added at up to 4 fluid ounces per 2 mixed gallons of parts A and B.
[15] Meets the health effects requirements of NSF/ANSI/CAN 600 according to requirements of
     NSF/ANSI/CAN 61 for pump, valve, and fitting end use.
[16] Colors: 00WH Tnemec White, 1211 Red, 1255 Beige, 15BL Tank white, 35GR Black, 39BL Delft
     Blue, B2506 DeZurik Blue, B5712 Westech Blue, 11SF True Blue, B9118 Baker Blue, B7896
     S-B Blue, Y2606 Romac Yellow, B2592 RAL 5009 Azurblau, B7011 Crispin Blue, B9695 Houston
     Blue, A14130 Mueller Gray, R5477 Mueller Sienna Red.
     Number of Coats: 2-3
     Sequence of Coats: Any combination of Listed colors
     Maximum Field Use Dry film Thickness (in mils): 18
     Maximum Thinner: 5% Tnemec No. 60 Thinner by volume
     Recoat Cure Time and Temperature: 5 hours at 75°F 
     Final Cure Time and Temperature: 30 days at 75°F
     Special Comments: Any listed color of series 22, FC22, or N140 may be substituted as a
     primer or topcoat for the Series N140 Pota-Pox Plus provided that both primer and
     topcoat meet their individual Certified end uses.  Mix ratio of Part A:Part B is 1:1 by
     volume.
[22] Certified for mechanical device end use (other than pump and valve) for a maximum of 4.6
     sq. ft. per gpm. 
[23] Certified for mechanical device end use (other than pump and valve) for a maximum of
     50.5 sq. ft. per gpm.
[24] Certified for mechanical device end use (other than pump and valve) for a maximum of 151
     sq. ft. per gpm when used with Thinner #2 and 189 sq. ft. per gpm when used with Thinner
     #3.
[25] This coating used with Thinner #49 is Certified for mechanical device end use (other
     than pump and valve) for a maximum of 310 sq. ft. per gpm. 
[26] Certified for mechanical device end use (other than pump and valve) for a maximum of 635
     sq. ft. per gpm.
[27] Certified for mechanical device end use (other than pump and valve) for a maximum of 151
     sq. ft per gpm.

Coatings - Pipe
22 Epoxoline[1] [2] >= 10" CLD 23 EPOXY
N140F Pota-Pox Plus Fast Cure [2] [3] >= 36" CLD 23 EPOXY
Series 91-H2O ™ Hydro-Zinc™ [2] [5] [6] [7] >= 24" CLD 23 EPOXY
Series 93-H20 Hydro-Zinc[8] >= 24" CLD 23 PUR
Series 94-H2O Hydro-Zinc[2] [9] [17] CLD 23 PUR
Series N140 Pota-Pox Plus[2] [13] >= 36" CLD 23 EPOXY

[1] Colors: 1255 Beige, 1218 Blue, WH11 White
    Number of Coats: 1-2
    Maximum Field Use Dry Film Thickness (in mils): 50
    Maximum Thinner: 5% Thinner #2
    Recoat Cure Time and Temperature: 16 hours at 75°F
    Final Cure Time and Temperature: 5 days at 75°F
    Special Comments: Mix ratio of Part A to Part B is 1:1 by volume.  Optional use with
    fiberglass flake S211-0220.  The fiberglass flake can be added up to a rate of 1% by
    weight after the Parts A and B are mixed together.  Certified for use as a primer or
    topcoat with any NSF Certified Tnemec coating system provided that both primer and
    topcoat meet their individual certified end uses.
[2] Meets the health effects requirements of NSF/ANSI/CAN 600 according to the requirements
    of NSF/ANSI/CAN 61 including the most current health effects criteria for xylenes,
    toluene, and ethylbenzene. 
[3] Colors: 15BL Tank White, 1255 Beige, 1211 Red, 35GR Black, 39BL Delft Blue, Y2606 Romac
    Yellow, 00WH Tnemec White, 11SF True Blue, B9118 Baker Blue, B5712 Westech Blue, B2592
    RAL 5009 Azurblau, B9695 Houston Blue, A14130 Mueller Gray, R5477 Mueller Sienna Red.
    Number of Coats: 1
    Sequence of Coats: 4 mils
    Maximum Thinner: 10% No. 4 Thinner by volume
    Recoat Cure Time and Temperature: 5 hours at 75F
    Final Cure Time/Temperature: 7 days at 75F (entire system)
    Special Comments: Mix ration is 1 Part A to 1 Part B by volume. Certified for use as an
    optional primer or intermediate topcoat with any Tnemec NSF certified primer and topcoat
    coating system provided the primer, intermediate, and topcoat meet their certified end
    uses. 
[5] This coating used with Thinner #3 is Certified for use in pipes >=24", tanks >=1500
    gallons, fittings >=1/2", pumps >=1/2", valves >=2".
[6] Colors: Greenish-Gray
    Number of Coats: 1
    Maximum Field Use Dry Thickness (in mils): 4
    Maximum Thinner: 10% Thinner #2 or Thinner #3 by volume
    Final Cure Time/Temperature: 4 hours at 75F; 2 hours at 75F wen accelerator is used. 
    Special Comments: Series 44-710 Urethane Accelerator may be added up to 4 fl.oz/gal.
    Series 91-H2O Hydro-Zinc ™ is approved for use with any NSF Certified Tnemec topcoat or
    coatings system providing that both primer and topcoat meet their individual Certified
    end uses. Mix Ratio Part A:B is 70%:30% by volume.
[7] This coating used with Thinner #2 is Certified for use in pipes >=24", tanks >=3000
    gallons, fittings >=1", pumps >=1/2", and valves >=4".
[8] Colors: Greenish-Gray
    Maximum Field Use Dry Thickness(in mils): 4 mils
    Maximum Thinner: 10% Thinner #2 by volume
    Final Cure Time/Temperature: 8 hours at 75F. 4 hours at 75F if accelerator is used. 
    Special Comments: Series 44-710 accelerator may be used up to 4 fluid oz/gal. 93-H20
    Hydro-Zinc is approved for use with any NSF Certified Tnemec topcoat or coating system
    providing that both primer and topcoat meet their individual Certified end uses.
[9] Colors: Greenish-gray
    Number of Coats: 1
    Maximum Field Use Dry Film Thickness (in mils): 4
    Maximum Thinner: 15% Tnemec No. 49 or 10% Thinner No. 2 or 10% Thinner No. 3 by volume
    Final Cure Time and Temperature: 8 hours at 75°F; 2 hours at 75°F when the accelerator
    is used 
    Special Comments: Series 44-710 Urethane Accelerator may be added up to 4 fl. oz/gal. 
    94-H2O is aproved for use with any NSF Certified Tnemec topcoat or coating system.
[13] Colors: 00WH Tnemec White, 1211 Red, 1255 Beige, 15BL Tank white, 35GR Black, 39BL Delft
     blue, B5712 Westech Blue, 11SF True Blue, B9118 Baker Blue, B8314 Krausz Blue, Y2606
     Romac Yellow, B2592 RAL 5009 Azurblau, B7011 Crispin Blue, B2506 Dezurik Blue, A14130
     Mueller Gray, B9695 Houston Blue, R5477 Mueller Sienna Red.
     Number of Coats: 1
     Maximum Field Use Dry Thickness(in mils): 4 mils
     Maximum Thinner: 10% No. 4 Thinner by volume
     Recoat Cure Time and Temperature: 5 hours at 75°F
     Final Cure Time and Temperature: 7 days at 75°F (entire system)
     Special Comments: Mix ratio is 1 Part A to 1 Part B by volume. Certified for use as an
     optional primer or intermediate coat with any Tnemec NSF certified primer and topcoat
     coating system provided the primer, intermediate, and topcoat meet their certified end
     uses.
[17] This coating used with Thinner #49 is Certified for use in pipes >= 18". This coating
     used with Thinner #2 and Thinner #3 is Certified for use in pipes >=24". 

Coatings - Pump
22 Epoxoline[1] [2] >= 1/2" CLD 23 EPOXY
N140F Pota-Pox Plus Fast Cure[2] [3] >= 4" CLD 23 EPOXY
Series 21 Epoxoline[2] [4] >= 4” CLD 23 EPOXY
Series 91-H2O ™ Hydro-Zinc™ [2] [5] [6] [7] >= 1/2" CLD 23 EPOXY
Series 93-H20 Hydro-Zinc[8] >= 1/2" CLD 23 PUR
Series 94-H2O Hydro-Zinc[2] [9] [18] >1/2" CLD 23 PUR
Series N140 Pota-Pox Plus[14] [15] >= 4" CLD 23 EPOXY
Series N140 Pota-Pox Plus [2] [13] >= 4" CLD 23 EPOXY
Series N140F Pota-Pox Plus Fast Cure[15] [16] >= 4" CLD 23 EPOXY

[1] Colors: 1255 Beige, 1218 Blue, WH11 White
    Number of Coats: 1-2
    Maximum Field Use Dry Film Thickness (in mils): 50
    Maximum Thinner: 5% Thinner #2
    Recoat Cure Time and Temperature: 16 hours at 75°F
    Final Cure Time and Temperature: 5 days at 75°F
    Special Comments: Mix ratio of Part A to Part B is 1:1 by volume.  Optional use with
    fiberglass flake S211-0220.  The fiberglass flake can be added up to a rate of 1% by
    weight after the Parts A and B are mixed together.  Certified for use as a primer or
    topcoat with any NSF Certified Tnemec coating system provided that both primer and
    topcoat meet their individual certified end uses.
[2] Meets the health effects requirements of NSF/ANSI/CAN 600 according to the requirements
    of NSF/ANSI/CAN 61 including the most current health effects criteria for xylenes,
    toluene, and ethylbenzene. 
[3] Colors: 15BL Tank White, 1255 Beige, 1211 Red, 35GR Black, 39BL Delft Blue, Y2606 Romac
    Yellow, 00WH Tnemec White, 11SF True Blue, B9118 Baker Blue, B5712 Westech Blue, B2592
    RAL 5009 Azurblau, B9695 Houston Blue, A14130 Mueller Gray, R5477 Mueller Sienna Red.
    Number of Coats: 1
    Sequence of Coats: 4 mils
    Maximum Thinner: 10% No. 4 Thinner by volume
    Recoat Cure Time and Temperature: 5 hours at 75F
    Final Cure Time/Temperature: 7 days at 75F (entire system)
    Special Comments: Mix ration is 1 Part A to 1 Part B by volume. Certified for use as an
    optional primer or intermediate topcoat with any Tnemec NSF certified primer and topcoat
    coating system provided the primer, intermediate, and topcoat meet their certified end
    uses. 
[4] Colors: WH16 OFF-WHITE, 35GR Black, 33GR Gray, 39BL Delft Blue, 1255 Beige, B5712
    Westech Blue, 11SF True Blue/Safety, 1211 Red Primer, A13096 Baker Dark Gray, B2592
    RAL5009 Azurblau, B2506 Dezurik Blue, B9918 New Baker Blue
    Number of Coats: 1-3
    Maximum Field Use Dry Thickness (in mils): 20
    Maximum Thinner: 5% F041-0088 Thinner Clear by volume
    Recoat Cure Time and Temperature: 8 hours at 75F
    Final Cure Time/Temperature: 7 days at 75F
    Special Comments: Mix ratio of A:B is 2:1 by volume. Series 21 Epoxoline is approved for
    use as a primer or topcoat with any NSF Certified Tnemec topcoat or coating system
    providing that both primer and topcoat meet their individual Certified end uses.
[5] This coating used with Thinner #3 is Certified for use in pipes >=24", tanks >=1500
    gallons, fittings >=1/2", pumps >=1/2", valves >=2".
[6] Colors: Greenish-Gray
    Number of Coats: 1
    Maximum Field Use Dry Thickness (in mils): 4
    Maximum Thinner: 10% Thinner #2 or Thinner #3 by volume
    Final Cure Time/Temperature: 4 hours at 75F; 2 hours at 75F wen accelerator is used. 
    Special Comments: Series 44-710 Urethane Accelerator may be added up to 4 fl.oz/gal.
    Series 91-H2O Hydro-Zinc ™ is approved for use with any NSF Certified Tnemec topcoat or
    coatings system providing that both primer and topcoat meet their individual Certified
    end uses. Mix Ratio Part A:B is 70%:30% by volume.
[7] This coating used with Thinner #2 is Certified for use in pipes >=24", tanks >=3000
    gallons, fittings >=1", pumps >=1/2", and valves >=4".
[8] Colors: Greenish-Gray
    Maximum Field Use Dry Thickness(in mils): 4 mils
    Maximum Thinner: 10% Thinner #2 by volume
    Final Cure Time/Temperature: 8 hours at 75F. 4 hours at 75F if accelerator is used. 
    Special Comments: Series 44-710 accelerator may be used up to 4 fluid oz/gal. 93-H20
    Hydro-Zinc is approved for use with any NSF Certified Tnemec topcoat or coating system
    providing that both primer and topcoat meet their individual Certified end uses.
[9] Colors: Greenish-gray
    Number of Coats: 1
    Maximum Field Use Dry Film Thickness (in mils): 4
    Maximum Thinner: 15% Tnemec No. 49 or 10% Thinner No. 2 or 10% Thinner No. 3 by volume
    Final Cure Time and Temperature: 8 hours at 75°F; 2 hours at 75°F when the accelerator
    is used 
    Special Comments: Series 44-710 Urethane Accelerator may be added up to 4 fl. oz/gal. 
    94-H2O is aproved for use with any NSF Certified Tnemec topcoat or coating system.
[13] Colors: 00WH Tnemec White, 1211 Red, 1255 Beige, 15BL Tank white, 35GR Black, 39BL Delft
     blue, B5712 Westech Blue, 11SF True Blue, B9118 Baker Blue, B8314 Krausz Blue, Y2606
     Romac Yellow, B2592 RAL 5009 Azurblau, B7011 Crispin Blue, B2506 Dezurik Blue, A14130
     Mueller Gray, B9695 Houston Blue, R5477 Mueller Sienna Red.
     Number of Coats: 1
     Maximum Field Use Dry Thickness(in mils): 4 mils
     Maximum Thinner: 10% No. 4 Thinner by volume
     Recoat Cure Time and Temperature: 5 hours at 75°F
     Final Cure Time and Temperature: 7 days at 75°F (entire system)
     Special Comments: Mix ratio is 1 Part A to 1 Part B by volume. Certified for use as an
     optional primer or intermediate coat with any Tnemec NSF certified primer and topcoat
     coating system provided the primer, intermediate, and topcoat meet their certified end
     uses.
[14] Colors: 00WH Tnemec White, 1211 Red, 1255 Beige, 15BL Tank White, 35GR Black, 39BL Delft
     Blue, B5712 Westech Blue, 11SF True Blue, B9118 Baker Blue, B8314 Krausz Blue, A13096
     Baker Dark Gray, Y2606 Romac Yellow, B2592 RAL 5009 Azurblau, B7011 Crispin Blue, B2506
     Dezurik Blue, A14130 Mueller Gray, B9695 Houston Blue, R5477 Mueller Sienna Red.
     Number of Coats: 2-3
     Sequence of Coats: Any combination of Listed colors
     Maximum Field Use Dry Film Thickness (in mils): 18
     Maximum Thinner: 5% Tnemec No. 60 Thinner by volume
     Recoat Cure Time and Temperature: 5 hours at 75°F with accelerator, 9 hours at 75°F
     without accelerator
     Final Cure Time and Temperature: 30 days at 75°F
     Special Comments: Any Listed color of Series 22, FC22, or N140, may be substituted as a
     primer of topcoat for Series N140 Pota-Pox Plus provided that both primer and topcoat
     meet their individual Certified end uses.  The mix ratio of Part A:Part B is 1:1 by
     volume.  Part C (Series 44-700 Accelerator) is an optional additive to Part A in the
     field and may be added at up to 4 fluid ounces per 2 mixed gallons of parts A and B.
[15] Meets the health effects requirements of NSF/ANSI/CAN 600 according to requirements of
     NSF/ANSI/CAN 61 for pump, valve, and fitting end use.
[16] Colors: 00WH Tnemec White, 1211 Red, 1255 Beige, 15BL Tank white, 35GR Black, 39BL Delft
     Blue, B2506 DeZurik Blue, B5712 Westech Blue, 11SF True Blue, B9118 Baker Blue, B7896
     S-B Blue, Y2606 Romac Yellow, B2592 RAL 5009 Azurblau, B7011 Crispin Blue, B9695 Houston
     Blue, A14130 Mueller Gray, R5477 Mueller Sienna Red.
     Number of Coats: 2-3
     Sequence of Coats: Any combination of Listed colors
     Maximum Field Use Dry film Thickness (in mils): 18
     Maximum Thinner: 5% Tnemec No. 60 Thinner by volume
     Recoat Cure Time and Temperature: 5 hours at 75°F 
     Final Cure Time and Temperature: 30 days at 75°F
     Special Comments: Any listed color of series 22, FC22, or N140 may be substituted as a
     primer or topcoat for the Series N140 Pota-Pox Plus provided that both primer and
     topcoat meet their individual Certified end uses.  Mix ratio of Part A:Part B is 1:1 by
     volume.
[18] This coating used with Thinner #49, Thinner #2 and Thinner #3 is Certified for use in
     pumps >= 1/2". 

Coatings - Tank
22 Epoxoline[1] [2] >= 50 gal. CLD 23 EPOXY
N140F Pota-Pox Plus Fast Cure [2] [3] >= 1,500 gal. CLD 23 EPOXY
Series 21 Epoxoline [2] [4] >= 90,000 gal. CLD 23 EPOXY
Series 406 Elastoshield[2] [19] >= 50,000 gal. CLD 23 PUR
Series 91-H2O ™ Hydro-Zinc™ [2] [6] [7] >= 3000 gal. CLD 23 EPOXY
Series 91-H2O ™ Hydro-Zinc™ [2] [5] [6] >= 1500 gal. CLD 23 EPOXY
Series 93-H20 Hydro-Zinc[8] >= 3,000 gal CLD 23 PUR
Series 94-H2O Hydro Zinc[2] [9] [20] CLD 23 PUR
Series L140 Pota-Pox Plus [2] [12] >= 50,000 gal. CLD 23 EPOXY
Series L140F Pota-Pox Plus Fast Cure [2] [12] >= 50,000 gal. CLD 23 EPOXY
Series N140 Pota-Pox Plus [2] [13] >= 1,500 gal. CLD 23 EPOXY

[1] Colors: 1255 Beige, 1218 Blue, WH11 White
    Number of Coats: 1-2
    Maximum Field Use Dry Film Thickness (in mils): 50
    Maximum Thinner: 5% Thinner #2
    Recoat Cure Time and Temperature: 16 hours at 75°F
    Final Cure Time and Temperature: 5 days at 75°F
    Special Comments: Mix ratio of Part A to Part B is 1:1 by volume.  Optional use with
    fiberglass flake S211-0220.  The fiberglass flake can be added up to a rate of 1% by
    weight after the Parts A and B are mixed together.  Certified for use as a primer or
    topcoat with any NSF Certified Tnemec coating system provided that both primer and
    topcoat meet their individual certified end uses.
[2] Meets the health effects requirements of NSF/ANSI/CAN 600 according to the requirements
    of NSF/ANSI/CAN 61 including the most current health effects criteria for xylenes,
    toluene, and ethylbenzene. 
[3] Colors: 15BL Tank White, 1255 Beige, 1211 Red, 35GR Black, 39BL Delft Blue, Y2606 Romac
    Yellow, 00WH Tnemec White, 11SF True Blue, B9118 Baker Blue, B5712 Westech Blue, B2592
    RAL 5009 Azurblau, B9695 Houston Blue, A14130 Mueller Gray, R5477 Mueller Sienna Red.
    Number of Coats: 1
    Sequence of Coats: 4 mils
    Maximum Thinner: 10% No. 4 Thinner by volume
    Recoat Cure Time and Temperature: 5 hours at 75F
    Final Cure Time/Temperature: 7 days at 75F (entire system)
    Special Comments: Mix ration is 1 Part A to 1 Part B by volume. Certified for use as an
    optional primer or intermediate topcoat with any Tnemec NSF certified primer and topcoat
    coating system provided the primer, intermediate, and topcoat meet their certified end
    uses. 
[4] Colors: WH16 OFF-WHITE, 35GR Black, 33GR Gray, 39BL Delft Blue, 1255 Beige, B5712
    Westech Blue, 11SF True Blue/Safety, 1211 Red Primer, A13096 Baker Dark Gray, B2592
    RAL5009 Azurblau, B2506 Dezurik Blue, B9918 New Baker Blue
    Number of Coats: 1-3
    Maximum Field Use Dry Thickness (in mils): 20
    Maximum Thinner: 5% F041-0088 Thinner Clear by volume
    Recoat Cure Time and Temperature: 8 hours at 75F
    Final Cure Time/Temperature: 7 days at 75F
    Special Comments: Mix ratio of A:B is 2:1 by volume. Series 21 Epoxoline is approved for
    use as a primer or topcoat with any NSF Certified Tnemec topcoat or coating system
    providing that both primer and topcoat meet their individual Certified end uses.
[5] This coating used with Thinner #3 is Certified for use in pipes >=24", tanks >=1500
    gallons, fittings >=1/2", pumps >=1/2", valves >=2".
[6] Colors: Greenish-Gray
    Number of Coats: 1
    Maximum Field Use Dry Thickness (in mils): 4
    Maximum Thinner: 10% Thinner #2 or Thinner #3 by volume
    Final Cure Time/Temperature: 4 hours at 75F; 2 hours at 75F wen accelerator is used. 
    Special Comments: Series 44-710 Urethane Accelerator may be added up to 4 fl.oz/gal.
    Series 91-H2O Hydro-Zinc ™ is approved for use with any NSF Certified Tnemec topcoat or
    coatings system providing that both primer and topcoat meet their individual Certified
    end uses. Mix Ratio Part A:B is 70%:30% by volume.
[7] This coating used with Thinner #2 is Certified for use in pipes >=24", tanks >=3000
    gallons, fittings >=1", pumps >=1/2", and valves >=4".
[8] Colors: Greenish-Gray
    Maximum Field Use Dry Thickness(in mils): 4 mils
    Maximum Thinner: 10% Thinner #2 by volume
    Final Cure Time/Temperature: 8 hours at 75F. 4 hours at 75F if accelerator is used. 
    Special Comments: Series 44-710 accelerator may be used up to 4 fluid oz/gal. 93-H20
    Hydro-Zinc is approved for use with any NSF Certified Tnemec topcoat or coating system
    providing that both primer and topcoat meet their individual Certified end uses.
[9] Colors: Greenish-gray
    Number of Coats: 1
    Maximum Field Use Dry Film Thickness (in mils): 4
    Maximum Thinner: 15% Tnemec No. 49 or 10% Thinner No. 2 or 10% Thinner No. 3 by volume
    Final Cure Time and Temperature: 8 hours at 75°F; 2 hours at 75°F when the accelerator
    is used 
    Special Comments: Series 44-710 Urethane Accelerator may be added up to 4 fl. oz/gal. 
    94-H2O is aproved for use with any NSF Certified Tnemec topcoat or coating system.
[12] Colors: 1255 Beige, 15BL Tank White, 1211 Red, 00WH White 
     # of coats: 2-3
     # Seq Of Coats: Any combination of listed colors
     Max Film Thickness: 18 (Maximum of 6 mils per coat)
     Max Thinner: 5% Tnemec No. 49 Thinner by volume
     Recoat Cure Time/ Temp.:  16 hours at 75° F 
     Final Cure Time/ Temp.: 7 days at 75° F 
     Special Comments: Series N140, N140F, V140, V140F, L140 and Series 22, FC22 may be
     substituted as a primer or topcoat for L140F provided that both primer and topcoat meet
     their individual Certified end uses.  Mix ratio of Part A to Part B is 1:1 by volume.
[13] Colors: 00WH Tnemec White, 1211 Red, 1255 Beige, 15BL Tank white, 35GR Black, 39BL Delft
     blue, B5712 Westech Blue, 11SF True Blue, B9118 Baker Blue, B8314 Krausz Blue, Y2606
     Romac Yellow, B2592 RAL 5009 Azurblau, B7011 Crispin Blue, B2506 Dezurik Blue, A14130
     Mueller Gray, B9695 Houston Blue, R5477 Mueller Sienna Red.
     Number of Coats: 1
     Maximum Field Use Dry Thickness(in mils): 4 mils
     Maximum Thinner: 10% No. 4 Thinner by volume
     Recoat Cure Time and Temperature: 5 hours at 75°F
     Final Cure Time and Temperature: 7 days at 75°F (entire system)
     Special Comments: Mix ratio is 1 Part A to 1 Part B by volume. Certified for use as an
     optional primer or intermediate coat with any Tnemec NSF certified primer and topcoat
     coating system provided the primer, intermediate, and topcoat meet their certified end
     uses.
[19] Colors: WH06 Off-White	
     Number of Coats: 1-2
     Sequence of Coats: Primer (optional), Series 406 Elastoshield (topcoat)
     Maximum Field Use Dry Film Thickness (in mils): Topcoat-75
     Recoat Cure Time and Temperature: 5 hours at 75°F
     Final Cure Time and Temperature: 72 hours at 75°F
     Special Comments: Mix ratio for primers must meet their individual certified parameters.
     Mix ratio of A:B is 1:2 by volume for Topcoat. Certified for use as a topcoat with any
     Tnemec NSF Certified coating system provided both primer and topcoat meet their
     individual certified end uses.
[20] This coating used with Thinner #49 is Certified for use in tanks >= 400 gallons. This
     coating used with Thinner #2 is Certified for use in tank >=3000 gallons. This coating
     used with Thinner #3 is Certified for use in tanks >=1500 gallons. 

Coatings - Valve
22 Epoxoline[1] [2] >= 1/2" CLD 23 EPOXY
N140F Pota-Pox Plus Fast Cure[2] [3] >= 4" CLD 23 EPOXY
Series 21 Epoxoline[2] [4] >= 4" CLD 23 EPOXY
Series 406 Elastoshield[2] [19] >= 4" CLD 23 PUR
Series 91-H2O ™ Hydro-Zinc™ [2] [5] [6] >= 2" CLD 23 EPOXY
Series 91-H2O™ Hydro-Zinc™ [2] [6] [7] >= 4" CLD 23 EPOXY
Series 93-H20 Hydro-Zinc[8] >= 4" CLD 23 PUR
Series 94-H2O Hydro-Zinc[2] [9] [21] CLD 23 PUR
Series N140 Pota-Pox Plus[14] [15] >= 4" CLD 23 EPOXY
Series N140 Pota-Pox Plus [2] [13] >= 4" CLD 23 EPOXY
Series N140F Pota-Pox Plus Fast Cure[15] [16] >= 4" CLD 23 EPOXY

[1] Colors: 1255 Beige, 1218 Blue, WH11 White
    Number of Coats: 1-2
    Maximum Field Use Dry Film Thickness (in mils): 50
    Maximum Thinner: 5% Thinner #2
    Recoat Cure Time and Temperature: 16 hours at 75°F
    Final Cure Time and Temperature: 5 days at 75°F
    Special Comments: Mix ratio of Part A to Part B is 1:1 by volume.  Optional use with
    fiberglass flake S211-0220.  The fiberglass flake can be added up to a rate of 1% by
    weight after the Parts A and B are mixed together.  Certified for use as a primer or
    topcoat with any NSF Certified Tnemec coating system provided that both primer and
    topcoat meet their individual certified end uses.
[2] Meets the health effects requirements of NSF/ANSI/CAN 600 according to the requirements
    of NSF/ANSI/CAN 61 including the most current health effects criteria for xylenes,
    toluene, and ethylbenzene. 
[3] Colors: 15BL Tank White, 1255 Beige, 1211 Red, 35GR Black, 39BL Delft Blue, Y2606 Romac
    Yellow, 00WH Tnemec White, 11SF True Blue, B9118 Baker Blue, B5712 Westech Blue, B2592
    RAL 5009 Azurblau, B9695 Houston Blue, A14130 Mueller Gray, R5477 Mueller Sienna Red.
    Number of Coats: 1
    Sequence of Coats: 4 mils
    Maximum Thinner: 10% No. 4 Thinner by volume
    Recoat Cure Time and Temperature: 5 hours at 75F
    Final Cure Time/Temperature: 7 days at 75F (entire system)
    Special Comments: Mix ration is 1 Part A to 1 Part B by volume. Certified for use as an
    optional primer or intermediate topcoat with any Tnemec NSF certified primer and topcoat
    coating system provided the primer, intermediate, and topcoat meet their certified end
    uses. 
[4] Colors: WH16 OFF-WHITE, 35GR Black, 33GR Gray, 39BL Delft Blue, 1255 Beige, B5712
    Westech Blue, 11SF True Blue/Safety, 1211 Red Primer, A13096 Baker Dark Gray, B2592
    RAL5009 Azurblau, B2506 Dezurik Blue, B9918 New Baker Blue
    Number of Coats: 1-3
    Maximum Field Use Dry Thickness (in mils): 20
    Maximum Thinner: 5% F041-0088 Thinner Clear by volume
    Recoat Cure Time and Temperature: 8 hours at 75F
    Final Cure Time/Temperature: 7 days at 75F
    Special Comments: Mix ratio of A:B is 2:1 by volume. Series 21 Epoxoline is approved for
    use as a primer or topcoat with any NSF Certified Tnemec topcoat or coating system
    providing that both primer and topcoat meet their individual Certified end uses.
[5] This coating used with Thinner #3 is Certified for use in pipes >=24", tanks >=1500
    gallons, fittings >=1/2", pumps >=1/2", valves >=2".
[6] Colors: Greenish-Gray
    Number of Coats: 1
    Maximum Field Use Dry Thickness (in mils): 4
    Maximum Thinner: 10% Thinner #2 or Thinner #3 by volume
    Final Cure Time/Temperature: 4 hours at 75F; 2 hours at 75F wen accelerator is used. 
    Special Comments: Series 44-710 Urethane Accelerator may be added up to 4 fl.oz/gal.
    Series 91-H2O Hydro-Zinc ™ is approved for use with any NSF Certified Tnemec topcoat or
    coatings system providing that both primer and topcoat meet their individual Certified
    end uses. Mix Ratio Part A:B is 70%:30% by volume.
[7] This coating used with Thinner #2 is Certified for use in pipes >=24", tanks >=3000
    gallons, fittings >=1", pumps >=1/2", and valves >=4".
[8] Colors: Greenish-Gray
    Maximum Field Use Dry Thickness(in mils): 4 mils
    Maximum Thinner: 10% Thinner #2 by volume
    Final Cure Time/Temperature: 8 hours at 75F. 4 hours at 75F if accelerator is used. 
    Special Comments: Series 44-710 accelerator may be used up to 4 fluid oz/gal. 93-H20
    Hydro-Zinc is approved for use with any NSF Certified Tnemec topcoat or coating system
    providing that both primer and topcoat meet their individual Certified end uses.
[9] Colors: Greenish-gray
    Number of Coats: 1
    Maximum Field Use Dry Film Thickness (in mils): 4
    Maximum Thinner: 15% Tnemec No. 49 or 10% Thinner No. 2 or 10% Thinner No. 3 by volume
    Final Cure Time and Temperature: 8 hours at 75°F; 2 hours at 75°F when the accelerator
    is used 
    Special Comments: Series 44-710 Urethane Accelerator may be added up to 4 fl. oz/gal. 
    94-H2O is aproved for use with any NSF Certified Tnemec topcoat or coating system.
[13] Colors: 00WH Tnemec White, 1211 Red, 1255 Beige, 15BL Tank white, 35GR Black, 39BL Delft
     blue, B5712 Westech Blue, 11SF True Blue, B9118 Baker Blue, B8314 Krausz Blue, Y2606
     Romac Yellow, B2592 RAL 5009 Azurblau, B7011 Crispin Blue, B2506 Dezurik Blue, A14130
     Mueller Gray, B9695 Houston Blue, R5477 Mueller Sienna Red.
     Number of Coats: 1
     Maximum Field Use Dry Thickness(in mils): 4 mils
     Maximum Thinner: 10% No. 4 Thinner by volume
     Recoat Cure Time and Temperature: 5 hours at 75°F
     Final Cure Time and Temperature: 7 days at 75°F (entire system)
     Special Comments: Mix ratio is 1 Part A to 1 Part B by volume. Certified for use as an
     optional primer or intermediate coat with any Tnemec NSF certified primer and topcoat
     coating system provided the primer, intermediate, and topcoat meet their certified end
     uses.
[14] Colors: 00WH Tnemec White, 1211 Red, 1255 Beige, 15BL Tank White, 35GR Black, 39BL Delft
     Blue, B5712 Westech Blue, 11SF True Blue, B9118 Baker Blue, B8314 Krausz Blue, A13096
     Baker Dark Gray, Y2606 Romac Yellow, B2592 RAL 5009 Azurblau, B7011 Crispin Blue, B2506
     Dezurik Blue, A14130 Mueller Gray, B9695 Houston Blue, R5477 Mueller Sienna Red.
     Number of Coats: 2-3
     Sequence of Coats: Any combination of Listed colors
     Maximum Field Use Dry Film Thickness (in mils): 18
     Maximum Thinner: 5% Tnemec No. 60 Thinner by volume
     Recoat Cure Time and Temperature: 5 hours at 75°F with accelerator, 9 hours at 75°F
     without accelerator
     Final Cure Time and Temperature: 30 days at 75°F
     Special Comments: Any Listed color of Series 22, FC22, or N140, may be substituted as a
     primer of topcoat for Series N140 Pota-Pox Plus provided that both primer and topcoat
     meet their individual Certified end uses.  The mix ratio of Part A:Part B is 1:1 by
     volume.  Part C (Series 44-700 Accelerator) is an optional additive to Part A in the
     field and may be added at up to 4 fluid ounces per 2 mixed gallons of parts A and B.
[15] Meets the health effects requirements of NSF/ANSI/CAN 600 according to requirements of
     NSF/ANSI/CAN 61 for pump, valve, and fitting end use.
[16] Colors: 00WH Tnemec White, 1211 Red, 1255 Beige, 15BL Tank white, 35GR Black, 39BL Delft
     Blue, B2506 DeZurik Blue, B5712 Westech Blue, 11SF True Blue, B9118 Baker Blue, B7896
     S-B Blue, Y2606 Romac Yellow, B2592 RAL 5009 Azurblau, B7011 Crispin Blue, B9695 Houston
     Blue, A14130 Mueller Gray, R5477 Mueller Sienna Red.
     Number of Coats: 2-3
     Sequence of Coats: Any combination of Listed colors
     Maximum Field Use Dry film Thickness (in mils): 18
     Maximum Thinner: 5% Tnemec No. 60 Thinner by volume
     Recoat Cure Time and Temperature: 5 hours at 75°F 
     Final Cure Time and Temperature: 30 days at 75°F
     Special Comments: Any listed color of series 22, FC22, or N140 may be substituted as a
     primer or topcoat for the Series N140 Pota-Pox Plus provided that both primer and
     topcoat meet their individual Certified end uses.  Mix ratio of Part A:Part B is 1:1 by
     volume.
[19] Colors: WH06 Off-White	
     Number of Coats: 1-2
     Sequence of Coats: Primer (optional), Series 406 Elastoshield (topcoat)
     Maximum Field Use Dry Film Thickness (in mils): Topcoat-75
     Recoat Cure Time and Temperature: 5 hours at 75°F
     Final Cure Time and Temperature: 72 hours at 75°F
     Special Comments: Mix ratio for primers must meet their individual certified parameters.
     Mix ratio of A:B is 1:2 by volume for Topcoat. Certified for use as a topcoat with any
     Tnemec NSF Certified coating system provided both primer and topcoat meet their
     individual certified end uses.
[21] This coating used with Thinner #49 is Certified for use in valves >=1/2". This coatings
     used with Thinner #2 is Certified for use in valves >= 4". This coating used with
     Thinner #3 is Certified for use in valves >= 2".



Facility : North Kansas City, MO

Protective (Barrier) Materials

    Water Water
  Water Contact Contact Contact
Trade Designation Size Restriction Temp Material

Coatings - Fittings
22 Epoxoline[1] [2] >= 6" CLD 23 EPOXY
F098-0H20 Hydro-Zinc[2] [3] >= 1" CLD 23 EPOXY
N140F Pota-Pox Plus Fast Cure[2] [4] >= 2" CLD 23 EPOXY
Series 1220 Tnemec Epoxy[5] >= 1/2" CLD 23 EPOXY
Series 21 Epoxoline[2] [7] >= 3/4" CLD 23 EPOXY
Series 21 Epoxoline[2] [6] >= 1/2" CLD 23 EPOXY
Series 91-H2O™ Hydro-Zinc™[2] [8] [9] [10] >= 1" CLD 23 PUR
Series 93-H20 Hydro-Zinc[11] >= 1" CLD 23 PUR
Series 94-H2O Hydro-Zinc[2] [12] [13] CLD 23 PUR
Series FC22 Epoxoline[2] [14] >= 1/2" CLD 23 EPOXY
Series L140 Pota-Pox Plus[2] [15] >= 1" CLD 23 EPOXY
Series L140F Pota-Pox Plus Fast Cure[2] [16] >= 1" CLD 23 EPOXY
Series N140 Pota-Pox Plus[18] [22] >= 4" CLD 23 EPOXY
Series N140 Pota-Pox Plus [2] [17] >= 2" CLD 23 EPOXY
Series N140F Pota-Pox Plus Fast Cure[18] [19] >= 4" CLD 23 EPOXY

[1] Colors: 1255 Beige, 1218 Blue, WH11 White
    Number of Coats: 1-2
    Maximum Field Use Dry Film Thickness (in mils): 50
    Maximum Thinner: 5% Thinner #2
    Recoat Cure Time and Temperature: 16 hours at 75°F 
    Final Cure Time and Temperature: 5 days at 75°F
    Special Comments: Mix ratio of Part A to Part B is 1:1 by volume.  Optional use with
    fiberglass flake S211-0220.  The fiberglass flake can be added up to a rate of 1% by
    weight after the Parts A and B are mixed together.  Certified for use as a primer or
    topcoat with any NSF Certified Tnemec coating system provided that both primer and
    topcoat meet their individual certified end uses.
[2] Meets the health effects requirements of NSF/ANSI/CAN 600 according to the requirements
    of NSF/ANSI/CAN 61 including the most current health effects criteria for xylenes,
    toluene, and ethylbenzene. 
[3] Colors: Greenish Gray
    Number of Coats: 1
    Maximum Field Use Dry Thickness (in mils): 4mils
    Maximum Thinner: 25% Water
    Recoat Cure Time and Temperature: 5 hours at 75F
    Final Cure Time/Temperature: 7 days at 75F
    Special Comments: Series 44-780 Accelerator may be added up to 1 fl. oz/gal. Series
    98-H2O Hydro-Zinc is approved for use as a primer with any NSF Certified Tnemec topcoat
    or coating system providing that both primer and topcoat meet their individual Certified
    end uses. Cure for Series 98-H2O Hydro-Zinc primer is 5 hours at 75F. Top-coat is then
    applied. Final cure is 7 days. Mix ratio of Part A:B:C is 1.4:0.6:1 by volume.
[4] Colors: 15BL Tank White, 1255 Beige, 1211 Red, 35GR Black, 39BL Delft Blue, Y2606 Romac
    Yellow, 00WH Tnemec White, 11SF True Blue, B9118 Baker Blue, B5712 Westech Blue, B2592
    RAL 5009 Azurblau,  B9695 Houston Blue, A14130 Mueller Gray, R5477 Mueller Sienna Red.
    Number of Coats: 1
    Sequence of Coats: 4 mils
    Maximum Thinner: 10% No. 4 Thinner by volume
    Recoat Cure Time and Temperature: 5 hours at 75F
    Final Cure Time/Temperature: 7 days at 75F (entire system)
    Special Comments: Mix ration is 1 Part A to 1 Part B by volume. Certified for use as an
    optional primer or intermediate topcoat with any Tnemec NSF certified primer and topcoat
    coating system provided the primer, intermediate, and topcoat meet their certified end
    uses. 
[5] Colors: White
    Number of Coats: 1-3
    Maximum Field Use Dry Thickness (in mils): 18 mils
    Maximum Thinner: 15% water
    Recoat Cure Time and Temperature: 6 hours at 75F
    Final Cure Time/Temperature: 7 days at 75F
    Special Comments: Series 44-700 Accelerator may be added up to 1 fl. oz./gal. Series
    1220 Tnemec Epoxy is approved for use as a primer or topcoat with any NSF Certified
    Tnemec topcoat or coating system providing that both primer and topcoat meet their
    individual Certified end uses. Mix ratio of Part A:Part B is 2:1 by volume.
[6] Colors: WH16 Off-White, 1255 Beige, 39BL Delft Blue, B5712 Westech Blue, 11SF True
    Blue/Safety, 1211 Red Primer, A13096 Baker Dark Gray, B2592 RAL5009 Azurblau, B2506
    Dezurik Blue, B9918 New Baker Blue
    Number of Coats: 2
    Maximum Field Use Dry Thickness(in mils): 20 mils
    Maximum Thinner: None
    Recoat Cure Time and Temperature: 16 hours at 75F
    Final Cure Time/Temperature: 30 days at 75F
    Special Comments: Mix ratio of A:B is 2:1 by volume. This is for pipe, fitting, pump and
    valve end use.
[7] Colors: WH16 OFF-WHITE, 35GR Black, 33GR Gray, 39BL Delft Blue, 1255 Beige, B5712
    Westech Blue, 11SF True Blue/Safety, 1211 Red Primer, A13096 Baker Dark Gray, B2592
    RAL5009 Azurblau, B2506 Dezurik Blue, B9918 New Baker Blue
    Number of Coats: 1-3
    Maximum Field Use Dry Thickness(in mils): 20
    Maximum Thinner: 5% F041-0088 Thinner Clear by volume
    Recoat Cure Time and Temperature: 8 hours at 75F
    Final Cure Time/Temperature: 7 days at 75F
    Special Comments: Mix ratio of A:B is 2:1 by volume. Series 21 Epoxoline is approved for
    use as a primer or topcoat with any NSF Certified Tnemec topcoat or coating system
    providing that both primer and topcoat meet their individual Certified end uses.
[8] Colors: Greenish-gray
    Number of Coats: 1
    Maximum Field Use Dry Film Thickness (in mils): 4
    Maximum Thinner: 10% Thinner No. 2 or 10% Thinner No. 3 by volume
    Final Cure Time and Temperature: 4 hours at 75°F; 2 hours at 75°F when the accelerator
    is used 
    Special Comments: Series 44-710 Urethane Accelerator may be added up to 4 fl. oz/gal. 
    Series 91-H2O™ Hydro-Zinc™ is approved for use with any NSF Certified Tnemec topcoat or
    coating system providing that both primer and topcoat meet their individual Certified
    end uses.  Mix ratio of Part A:Part B is 70%:30% by volume.
[9] This coating used with Thinner #2 is Certified for use in pipes >=96", tanks >=50,000
    gallons, fittings >=1", pumps >=1", and valves >=4".
[10] This coatings used with Thinner #3 is Certified for use in pipes >=96", tanks >=40,000
     gallons, fittings >=1", pumps >=1/2", and valves >=1.75".
[11] Colors: Greenish-Gray
     Maximum Field Use Dry Thickness(in mils): 4 mils
     Maximum Thinner: 10% Thinner #2 by volume
     Final Cure Time/Temperature: 8 hours at 75F. 4 hours at 75F if accelerator is used. 
     Special Comments: Series 44-710 accelerator may be used up to 4 fluid oz/gal. 93-H20
     Hydro-Zinc is approved for use with any NSF Certified Tnemec topcoat or coating system
     providing that both primer and topcoat meet their individual Certified end uses.
[12] Color: Greenish-Gray
     Number of Coats: 1
     Maximum Field Use Dry Film Thickness (in mils): 4
     Maximum Thinner: 15% Tnemec No. 49 by volume or 10% Thinner No. 3 or 10% Thinner No. 2
     Recoat Cure Time and Temperature: 8 hours at 75°F; 2 hours at 75°F when the accelerator
     is used  
     Special Comments: Series 44-710 may be added up to 4 fl. oz/gal. 94-H2O is approved for
     use with any NSF Certified Tnemec topcoat or coating system.
[13] This coating used with Thinner #49 is Certified for use in fittings >= ½”. This coating
     used with Thinner #2 and #3 is Certified for use in fittings >= 1”.
[14] Colors: WH08 White, R4875A Akzo Red, B8869A Epoxoline Blue
     Number of Coats: 1
     Sequence of Coats: N/A
     Maximum Field Use Dry Film Thickness (in mils): 80
     Maximum Thinner: None
     Final Cure Time and Temperature: 24 hours at 75°F
     Special Comments: Mix ratio of Part A:Part B is 1:2 by volume.  Any Listed color of
     series N140 or N140F may be used as a topcoat or primer for Series FC22 Epoxoline.
[15] Colors: 00WH White, 1211 Red, 1255 Beige, 15BL Tank White
     Number of Coats: 2-3
     Sequence of Coats: Any combination of Listed colors
     Maximum Field Use Dry Film Thickness (in mils): 18 (maximum of 6 mils per coat)
     Maximum Thinner: 5% Tnemec No. 49 Thinner by volume
     Recoat Cure Time and Temperature: 16 hours at 75°F
     Final Cure Time and Temperature: 7 days at 75°F
     Special Comments: Series N140, N140F, V140, V140F, L140 and Series 22, FC22 may be
     substituted as a primer or topcoat for L140 provided that both primer and topcoat meet
     their individual Certified end uses. Series 44-700 accelerator (Part C) may be added up
     to 4 fluid ounces per two mixed gallons of L140 Parts A and B. Mix ratio of A:B is 1:1
     by volume.
[16] Colors: 1255 Beige, 15BL Tank White, 1211 Red, 00WH White
     Number of Coats: 2-3
     Sequence of coats: Any combination of Listed colors
     Maximum Field Use Dry Film Thickness (in mils): 18 (maximum of 6 mils per coat)
     Maximum Thinner: 5% Tnemec No. 49 by volume
     Recoat Cure Time and Temperature: 16 hours at 75°F
     Final Cure Time and Temperature: 7 days at 75°F
     Special Comments: Series N140, N140F, V140, V140F, L140 and Series 22, FC22 may be
     substituted as a primer or topcoat for L140F provided that both primer and topcoat meet
     their individual Certified end uses. Mix ratio of Part A to Part B is 1:1 by volume.
[17] Colors: 00WH Tnemec White, 1211 Red, 1255 Beige, 15BL Tank white, 35GR Black, 39BL Delft
     blue, B5712 Westech Blue, 11SF True Blue, B9118 Baker Blue, B8314 Krausz Blue, Y2606
     Romac Yellow, B2592 RAL 5009 Azurblau, B7011 Crispin Blue, B2506 Dezurik Blue, B9695
     Houston Blue, A14130 Mueller Gray, R5477 Mueller Sienna Red.
     Number of Coats: 1
     Maximum Field Use Dry Thickness(in mils): 4 mils
     Maximum Thinner: 10% No. 4 Thinner by volume
     Recoat Cure Time and Temperature: 5 hours at 75°F
     Final Cure Time and Temperature: 7 days at 75°F (entire system)
     Special Comments: Mix ratio is 1 Part A to 1 Part B by volume. Certified for use
     as an optional primer or intermediate coat with any Tnemec NSF certified primer
     and topcoat coating system provided the primer, intermediate, and topcoat meet
     their certified end uses. Part C (Series 44-700 Accelerator) is an optional additive to
     Part A in the field and may be added at up to 4 fluid ounces per gallon of Part A.
[18] Meets the health effects requirements of NSF/ANSI/CAN 600 according to requirements of
     NSF/ANSI/CAN 61 for pump, valve, and fitting end use.
[19] Colors: 00WH Tnemec White, 1211 Red, 1255 Beige, 15BL Tank White, 35GR Black, 39BL Delft
     Blue, B2506 DeZurik Blue, B5712 Westech Blue, 11SF True Blue, B9118 Baker Blue, B7896
     S-B Blue, Y2606 Romac Yellow, B2592 RAL 5009 Azurblau, B7011 Crispin Blue, B9695 Houston
     Blue, A14130 Mueller Gray, R5477 Mueller Sienna Red.
     Number of Coats: 2-3
     Sequence of Coats: Any combination of Listed colors
     Maximum Field Use Dry Film Thickness (in mils): 18
     Maximum Thinner: 5% Tnemec No. 60 Thinner by volume
     Recoat Cure Time and Temperature: 5 hours at 75°F
     Final Cure Time and Temperature: 30 days at 75°F
     Special comments: Any listed color of Series 22, FC22, N140 or 141 may be substituted as
     a primer of topcoat for Series N140 Pota-Pox Plus provided that both primer and topcoat
     meet their individual Certified end uses.  The mix ratio of Part A:Part B is 1:1 by
     volume.
[22] Colors: 00WH Tnemec White, 1211 Red, 1255 Beige, 15BL Tank White, 35GR Black, 39BL Delft
     Blue, B5712 Westech Blue, 11SF True Blue, B9118 Baker Blue, B8314 Krausz Blue, A13096
     Baker Dark Gray, Y2606 Romac Yellow, B2592 RAL 5009 Azurblau, B7011 Crispin Blue, B2506
     Dezurik Blue, B9695 Houston Blue, A14130 Mueller Gray, R5477 Mueller Sienna Red.
     Number of Coats: 2-3
     Sequence of Coats: Any combination of Listed colors
     Maximum Field Use Dry Film Thickness (in mils): 18
     Maximum Thinner: 5% Tnemec No. 60 Thinner by volume
     Recoat Cure Time and Temperature: 5 hours at 75°F with accelerator, 9 hours at 75°F
     without accelerator
     Final Cure Time and Temperature: 30 days at 75°F
     Special Comments: Any Listed color of Series 22, FC22, N140, or 141 may be substituted
     as a primer of topcoat for Series N140 Pota-Pox Plus provided that both primer and
     topcoat meet their individual Certified end uses.  The mix ratio of Part A:Part B is 1:1
     by volume.  Part C (Series 44-700 Accelerator) is an optional addititve to Part A in the
     field and may be added at up to 4 fluid ounces per two mixed gallons of parts A and B.

Coatings - Mechanical Devices
22 Epoxoline [1] [2] [31] CLD 23 EPOXY
Series 21 Epoxoline [2] [7] [29] CLD 23 EPOXY
Series 91-H2O™ Hydro-Zinc™[2] [9] [10] [12] [30] CLD 23 PUR
Series 93-H20 Hydro-Zinc[11] [33] CLD 23 PUR
Series 94-H2O Hydro Zinc [2] [12] [30] [32] CLD 23 PUR
Series N140 Pota-Pox Plus [18] [22] [28] CLD 23 EPOXY
Series N140F Pota-Pox Plus Fast Cure[17] [19] [28] CLD 23 EPOXY

[1] Colors: 1255 Beige, 1218 Blue, WH11 White
    Number of Coats: 1-2
    Maximum Field Use Dry Film Thickness (in mils): 50
    Maximum Thinner: 5% Thinner #2
    Recoat Cure Time and Temperature: 16 hours at 75°F 
    Final Cure Time and Temperature: 5 days at 75°F
    Special Comments: Mix ratio of Part A to Part B is 1:1 by volume.  Optional use with
    fiberglass flake S211-0220.  The fiberglass flake can be added up to a rate of 1% by
    weight after the Parts A and B are mixed together.  Certified for use as a primer or
    topcoat with any NSF Certified Tnemec coating system provided that both primer and
    topcoat meet their individual certified end uses.
[2] Meets the health effects requirements of NSF/ANSI/CAN 600 according to the requirements
    of NSF/ANSI/CAN 61 including the most current health effects criteria for xylenes,
    toluene, and ethylbenzene. 
[7] Colors: WH16 OFF-WHITE, 35GR Black, 33GR Gray, 39BL Delft Blue, 1255 Beige, B5712
    Westech Blue, 11SF True Blue/Safety, 1211 Red Primer, A13096 Baker Dark Gray, B2592
    RAL5009 Azurblau, B2506 Dezurik Blue, B9918 New Baker Blue
    Number of Coats: 1-3
    Maximum Field Use Dry Thickness(in mils): 20
    Maximum Thinner: 5% F041-0088 Thinner Clear by volume
    Recoat Cure Time and Temperature: 8 hours at 75F
    Final Cure Time/Temperature: 7 days at 75F
    Special Comments: Mix ratio of A:B is 2:1 by volume. Series 21 Epoxoline is approved for
    use as a primer or topcoat with any NSF Certified Tnemec topcoat or coating system
    providing that both primer and topcoat meet their individual Certified end uses.
[9] This coating used with Thinner #2 is Certified for use in pipes >=96", tanks >=50,000
    gallons, fittings >=1", pumps >=1", and valves >=4".
[10] This coatings used with Thinner #3 is Certified for use in pipes >=96", tanks >=40,000
     gallons, fittings >=1", pumps >=1/2", and valves >=1.75".
[11] Colors: Greenish-Gray
     Maximum Field Use Dry Thickness(in mils): 4 mils
     Maximum Thinner: 10% Thinner #2 by volume
     Final Cure Time/Temperature: 8 hours at 75F. 4 hours at 75F if accelerator is used. 
     Special Comments: Series 44-710 accelerator may be used up to 4 fluid oz/gal. 93-H20
     Hydro-Zinc is approved for use with any NSF Certified Tnemec topcoat or coating system
     providing that both primer and topcoat meet their individual Certified end uses.
[12] Color: Greenish-Gray
     Number of Coats: 1
     Maximum Field Use Dry Film Thickness (in mils): 4
     Maximum Thinner: 15% Tnemec No. 49 by volume or 10% Thinner No. 3 or 10% Thinner No. 2
     Recoat Cure Time and Temperature: 8 hours at 75°F; 2 hours at 75°F when the accelerator
     is used  
     Special Comments: Series 44-710 may be added up to 4 fl. oz/gal. 94-H2O is approved for
     use with any NSF Certified Tnemec topcoat or coating system.
[17] Colors: 00WH Tnemec White, 1211 Red, 1255 Beige, 15BL Tank white, 35GR Black, 39BL Delft
     blue, B5712 Westech Blue, 11SF True Blue, B9118 Baker Blue, B8314 Krausz Blue, Y2606
     Romac Yellow, B2592 RAL 5009 Azurblau, B7011 Crispin Blue, B2506 Dezurik Blue, B9695
     Houston Blue, A14130 Mueller Gray, R5477 Mueller Sienna Red.
     Number of Coats: 1
     Maximum Field Use Dry Thickness(in mils): 4 mils
     Maximum Thinner: 10% No. 4 Thinner by volume
     Recoat Cure Time and Temperature: 5 hours at 75°F
     Final Cure Time and Temperature: 7 days at 75°F (entire system)
     Special Comments: Mix ratio is 1 Part A to 1 Part B by volume. Certified for use
     as an optional primer or intermediate coat with any Tnemec NSF certified primer
     and topcoat coating system provided the primer, intermediate, and topcoat meet
     their certified end uses. Part C (Series 44-700 Accelerator) is an optional additive to
     Part A in the field and may be added at up to 4 fluid ounces per gallon of Part A.
[18] Meets the health effects requirements of NSF/ANSI/CAN 600 according to requirements of
     NSF/ANSI/CAN 61 for pump, valve, and fitting end use.
[19] Colors: 00WH Tnemec White, 1211 Red, 1255 Beige, 15BL Tank White, 35GR Black, 39BL Delft
     Blue, B2506 DeZurik Blue, B5712 Westech Blue, 11SF True Blue, B9118 Baker Blue, B7896
     S-B Blue, Y2606 Romac Yellow, B2592 RAL 5009 Azurblau, B7011 Crispin Blue, B9695 Houston
     Blue, A14130 Mueller Gray, R5477 Mueller Sienna Red.
     Number of Coats: 2-3
     Sequence of Coats: Any combination of Listed colors
     Maximum Field Use Dry Film Thickness (in mils): 18
     Maximum Thinner: 5% Tnemec No. 60 Thinner by volume
     Recoat Cure Time and Temperature: 5 hours at 75°F
     Final Cure Time and Temperature: 30 days at 75°F
     Special comments: Any listed color of Series 22, FC22, N140 or 141 may be substituted as
     a primer of topcoat for Series N140 Pota-Pox Plus provided that both primer and topcoat
     meet their individual Certified end uses.  The mix ratio of Part A:Part B is 1:1 by
     volume.
[22] Colors: 00WH Tnemec White, 1211 Red, 1255 Beige, 15BL Tank White, 35GR Black, 39BL Delft
     Blue, B5712 Westech Blue, 11SF True Blue, B9118 Baker Blue, B8314 Krausz Blue, A13096
     Baker Dark Gray, Y2606 Romac Yellow, B2592 RAL 5009 Azurblau, B7011 Crispin Blue, B2506
     Dezurik Blue, B9695 Houston Blue, A14130 Mueller Gray, R5477 Mueller Sienna Red.
     Number of Coats: 2-3
     Sequence of Coats: Any combination of Listed colors
     Maximum Field Use Dry Film Thickness (in mils): 18
     Maximum Thinner: 5% Tnemec No. 60 Thinner by volume
     Recoat Cure Time and Temperature: 5 hours at 75°F with accelerator, 9 hours at 75°F
     without accelerator
     Final Cure Time and Temperature: 30 days at 75°F
     Special Comments: Any Listed color of Series 22, FC22, N140, or 141 may be substituted
     as a primer of topcoat for Series N140 Pota-Pox Plus provided that both primer and
     topcoat meet their individual Certified end uses.  The mix ratio of Part A:Part B is 1:1
     by volume.  Part C (Series 44-700 Accelerator) is an optional addititve to Part A in the
     field and may be added at up to 4 fluid ounces per two mixed gallons of parts A and B.
[28] Certified for mechanical device end use (other than pump and valve) for a maximum of 4.6
     sq. ft. per gpm. 
[29] Certified for mechanical device end use (other than pump and valve) for a maximum of 189
     sq. ft. per gpm.
[30] Certified for mechanical device end use (other than pump and valve) for a minimum of 60
     sq. ft. per gpm when used with Thinner #2 and 64 sq. ft. per gpm when used with Thinner
     #3. 
[31] Certified for mechanical device end use (other than pump and valve) for a maximum of 249
     sq. ft. per gpm.
[32] This coating used with Thinner #49 is Certified for mechanical device end use (other
     than pump and valve) for a maximum of 189 sq. Ft. per gpm. 
[33] Certified for mechanical device end use (other than pump and valve) for a maximum of 60
     sq. ft per gpm. 

Coatings - Pipe
22 Epoxoline[1] [2] >= 24" CLD 23 EPOXY
F098-0H20 Hydro-Zinc[2] [3] >= 120" CLD 23 EPOXY
N140F Pota-Pox Plus Fast Cure [2] [4] >= 42" CLD 23 EPOXY
Series 1 Omnithane 1216 Greenish-Gray[2] [20] >= 36" CLD 23 PUR
Series 1220 Tnemec Epoxy[2] [5] >= 6" CLD 23 EPOXY
Series 21 Epoxoline[2] [6] >= 18" CLD 23 EPOXY
Series 91-H2O™ Hydro-Zinc™[2] [8] [9] [10] >= 96" CLD 23 PUR
Series 93-H20 Hydro-Zinc [11] >= 96" CLD 23 PUR
Series 94-H2O Hydro-Zinc[2] [12] [21] CLD 23 PUR
Series FC22 Epoxoline[2] [14] >= 8" CLD 23 EPOXY
Series N140 Pota-Pox Plus [2] [17] >= 42" CLD 23 EPOXY

[1] Colors: 1255 Beige, 1218 Blue, WH11 White
    Number of Coats: 1-2
    Maximum Field Use Dry Film Thickness (in mils): 50
    Maximum Thinner: 5% Thinner #2
    Recoat Cure Time and Temperature: 16 hours at 75°F 
    Final Cure Time and Temperature: 5 days at 75°F
    Special Comments: Mix ratio of Part A to Part B is 1:1 by volume.  Optional use with
    fiberglass flake S211-0220.  The fiberglass flake can be added up to a rate of 1% by
    weight after the Parts A and B are mixed together.  Certified for use as a primer or
    topcoat with any NSF Certified Tnemec coating system provided that both primer and
    topcoat meet their individual certified end uses.
[2] Meets the health effects requirements of NSF/ANSI/CAN 600 according to the requirements
    of NSF/ANSI/CAN 61 including the most current health effects criteria for xylenes,
    toluene, and ethylbenzene. 
[3] Colors: Greenish Gray
    Number of Coats: 1
    Maximum Field Use Dry Thickness (in mils): 4mils
    Maximum Thinner: 25% Water
    Recoat Cure Time and Temperature: 5 hours at 75F
    Final Cure Time/Temperature: 7 days at 75F
    Special Comments: Series 44-780 Accelerator may be added up to 1 fl. oz/gal. Series
    98-H2O Hydro-Zinc is approved for use as a primer with any NSF Certified Tnemec topcoat
    or coating system providing that both primer and topcoat meet their individual Certified
    end uses. Cure for Series 98-H2O Hydro-Zinc primer is 5 hours at 75F. Top-coat is then
    applied. Final cure is 7 days. Mix ratio of Part A:B:C is 1.4:0.6:1 by volume.
[4] Colors: 15BL Tank White, 1255 Beige, 1211 Red, 35GR Black, 39BL Delft Blue, Y2606 Romac
    Yellow, 00WH Tnemec White, 11SF True Blue, B9118 Baker Blue, B5712 Westech Blue, B2592
    RAL 5009 Azurblau,  B9695 Houston Blue, A14130 Mueller Gray, R5477 Mueller Sienna Red.
    Number of Coats: 1
    Sequence of Coats: 4 mils
    Maximum Thinner: 10% No. 4 Thinner by volume
    Recoat Cure Time and Temperature: 5 hours at 75F
    Final Cure Time/Temperature: 7 days at 75F (entire system)
    Special Comments: Mix ration is 1 Part A to 1 Part B by volume. Certified for use as an
    optional primer or intermediate topcoat with any Tnemec NSF certified primer and topcoat
    coating system provided the primer, intermediate, and topcoat meet their certified end
    uses. 
[5] Colors: White
    Number of Coats: 1-3
    Maximum Field Use Dry Thickness (in mils): 18 mils
    Maximum Thinner: 15% water
    Recoat Cure Time and Temperature: 6 hours at 75F
    Final Cure Time/Temperature: 7 days at 75F
    Special Comments: Series 44-700 Accelerator may be added up to 1 fl. oz./gal. Series
    1220 Tnemec Epoxy is approved for use as a primer or topcoat with any NSF Certified
    Tnemec topcoat or coating system providing that both primer and topcoat meet their
    individual Certified end uses. Mix ratio of Part A:Part B is 2:1 by volume.
[6] Colors: WH16 Off-White, 1255 Beige, 39BL Delft Blue, B5712 Westech Blue, 11SF True
    Blue/Safety, 1211 Red Primer, A13096 Baker Dark Gray, B2592 RAL5009 Azurblau, B2506
    Dezurik Blue, B9918 New Baker Blue
    Number of Coats: 2
    Maximum Field Use Dry Thickness(in mils): 20 mils
    Maximum Thinner: None
    Recoat Cure Time and Temperature: 16 hours at 75F
    Final Cure Time/Temperature: 30 days at 75F
    Special Comments: Mix ratio of A:B is 2:1 by volume. This is for pipe, fitting, pump and
    valve end use.
[8] Colors: Greenish-gray
    Number of Coats: 1
    Maximum Field Use Dry Film Thickness (in mils): 4
    Maximum Thinner: 10% Thinner No. 2 or 10% Thinner No. 3 by volume
    Final Cure Time and Temperature: 4 hours at 75°F; 2 hours at 75°F when the accelerator
    is used 
    Special Comments: Series 44-710 Urethane Accelerator may be added up to 4 fl. oz/gal. 
    Series 91-H2O™ Hydro-Zinc™ is approved for use with any NSF Certified Tnemec topcoat or
    coating system providing that both primer and topcoat meet their individual Certified
    end uses.  Mix ratio of Part A:Part B is 70%:30% by volume.
[9] This coating used with Thinner #2 is Certified for use in pipes >=96", tanks >=50,000
    gallons, fittings >=1", pumps >=1", and valves >=4".
[10] This coatings used with Thinner #3 is Certified for use in pipes >=96", tanks >=40,000
     gallons, fittings >=1", pumps >=1/2", and valves >=1.75".
[11] Colors: Greenish-Gray
     Maximum Field Use Dry Thickness(in mils): 4 mils
     Maximum Thinner: 10% Thinner #2 by volume
     Final Cure Time/Temperature: 8 hours at 75F. 4 hours at 75F if accelerator is used. 
     Special Comments: Series 44-710 accelerator may be used up to 4 fluid oz/gal. 93-H20
     Hydro-Zinc is approved for use with any NSF Certified Tnemec topcoat or coating system
     providing that both primer and topcoat meet their individual Certified end uses.
[12] Color: Greenish-Gray
     Number of Coats: 1
     Maximum Field Use Dry Film Thickness (in mils): 4
     Maximum Thinner: 15% Tnemec No. 49 by volume or 10% Thinner No. 3 or 10% Thinner No. 2
     Recoat Cure Time and Temperature: 8 hours at 75°F; 2 hours at 75°F when the accelerator
     is used  
     Special Comments: Series 44-710 may be added up to 4 fl. oz/gal. 94-H2O is approved for
     use with any NSF Certified Tnemec topcoat or coating system.
[14] Colors: WH08 White, R4875A Akzo Red, B8869A Epoxoline Blue
     Number of Coats: 1
     Sequence of Coats: N/A
     Maximum Field Use Dry Film Thickness (in mils): 80
     Maximum Thinner: None
     Final Cure Time and Temperature: 24 hours at 75°F
     Special Comments: Mix ratio of Part A:Part B is 1:2 by volume.  Any Listed color of
     series N140 or N140F may be used as a topcoat or primer for Series FC22 Epoxoline.
[17] Colors: 00WH Tnemec White, 1211 Red, 1255 Beige, 15BL Tank white, 35GR Black, 39BL Delft
     blue, B5712 Westech Blue, 11SF True Blue, B9118 Baker Blue, B8314 Krausz Blue, Y2606
     Romac Yellow, B2592 RAL 5009 Azurblau, B7011 Crispin Blue, B2506 Dezurik Blue, B9695
     Houston Blue, A14130 Mueller Gray, R5477 Mueller Sienna Red.
     Number of Coats: 1
     Maximum Field Use Dry Thickness(in mils): 4 mils
     Maximum Thinner: 10% No. 4 Thinner by volume
     Recoat Cure Time and Temperature: 5 hours at 75°F
     Final Cure Time and Temperature: 7 days at 75°F (entire system)
     Special Comments: Mix ratio is 1 Part A to 1 Part B by volume. Certified for use
     as an optional primer or intermediate coat with any Tnemec NSF certified primer
     and topcoat coating system provided the primer, intermediate, and topcoat meet
     their certified end uses. Part C (Series 44-700 Accelerator) is an optional additive to
     Part A in the field and may be added at up to 4 fluid ounces per gallon of Part A.
[20] Colors: 1216 Greenish-Gray
     Number of Coats: 1
     Sequence of Coats: N/A
     Maximum Field Use Dry Film Thickness (in mils): 4
     Maximum Thinner: 10% Thinner No. 2
     Recoat Cure Time and Temperature: 8 hours at 75°F
     Special Comment: Series 44-710 may be added up to 4 fl. oz/gal. Approved for use as a
     primer with any NSF Certified Tnemec topcoat or coating system provided that both primer
     and topcoat meet their individual Certified end uses.
[21] This coating used with Thinner #49 is Certified for use in pipes <= 22”. This coating
     used with Thinner #2 and #3 is Certified for use in pipes >= 96”. 

Coatings - Pump
22 Epoxoline[1] [2] >= 4" CLD 23 EPOXY
F098-0H20 Hydro-Zinc[2] [3] >= 4" CLD 23 EPOXY
N140F Pota-Pox Plus Fast Cure[2] [4] >= 4" CLD 23 EPOXY
Series 1220 Tnemec Epoxy[2] [5] >= 1 1/2" CLD 23 EPOXY
Series 21 Epoxoline[2] [7] >= 4" CLD 23 EPOXY
Series 21 Epoxoline[2] [6] >= 1/2" CLD 23 EPOXY
Series 91-H2O ™ Hydro-Zinc™ [2] [8] [10] >= 1/2" CLD 23 PUR
Series 91-H2O™ Hydro-Zinc™[2] [8] [9] >= 1" CLD 23 PUR
Series 93-H20 Hydro-Zinc [11] >= 1" CLD 23 PUR
Series 94-H2O Hydro-Zinc[2] [12] [23] CLD 23 PUR
Series FC22 Epoxoline[2] [14] >= 2" CLD 23 EPOXY
Series N140 Pota-Pox Plus[2] [17] >= 4" CLD 23 EPOXY
Series N140 Pota-Pox Plus[18] [22] >= 4" CLD 23 EPOXY
Series N140F Pota-Pox Plus Fast Cure[18] [19] >= 4" CLD 23 EPOXY

[1] Colors: 1255 Beige, 1218 Blue, WH11 White
    Number of Coats: 1-2
    Maximum Field Use Dry Film Thickness (in mils): 50
    Maximum Thinner: 5% Thinner #2
    Recoat Cure Time and Temperature: 16 hours at 75°F 
    Final Cure Time and Temperature: 5 days at 75°F
    Special Comments: Mix ratio of Part A to Part B is 1:1 by volume.  Optional use with
    fiberglass flake S211-0220.  The fiberglass flake can be added up to a rate of 1% by
    weight after the Parts A and B are mixed together.  Certified for use as a primer or
    topcoat with any NSF Certified Tnemec coating system provided that both primer and
    topcoat meet their individual certified end uses.
[2] Meets the health effects requirements of NSF/ANSI/CAN 600 according to the requirements
    of NSF/ANSI/CAN 61 including the most current health effects criteria for xylenes,
    toluene, and ethylbenzene. 
[3] Colors: Greenish Gray
    Number of Coats: 1
    Maximum Field Use Dry Thickness (in mils): 4mils
    Maximum Thinner: 25% Water
    Recoat Cure Time and Temperature: 5 hours at 75F
    Final Cure Time/Temperature: 7 days at 75F
    Special Comments: Series 44-780 Accelerator may be added up to 1 fl. oz/gal. Series
    98-H2O Hydro-Zinc is approved for use as a primer with any NSF Certified Tnemec topcoat
    or coating system providing that both primer and topcoat meet their individual Certified
    end uses. Cure for Series 98-H2O Hydro-Zinc primer is 5 hours at 75F. Top-coat is then
    applied. Final cure is 7 days. Mix ratio of Part A:B:C is 1.4:0.6:1 by volume.
[4] Colors: 15BL Tank White, 1255 Beige, 1211 Red, 35GR Black, 39BL Delft Blue, Y2606 Romac
    Yellow, 00WH Tnemec White, 11SF True Blue, B9118 Baker Blue, B5712 Westech Blue, B2592
    RAL 5009 Azurblau,  B9695 Houston Blue, A14130 Mueller Gray, R5477 Mueller Sienna Red.
    Number of Coats: 1
    Sequence of Coats: 4 mils
    Maximum Thinner: 10% No. 4 Thinner by volume
    Recoat Cure Time and Temperature: 5 hours at 75F
    Final Cure Time/Temperature: 7 days at 75F (entire system)
    Special Comments: Mix ration is 1 Part A to 1 Part B by volume. Certified for use as an
    optional primer or intermediate topcoat with any Tnemec NSF certified primer and topcoat
    coating system provided the primer, intermediate, and topcoat meet their certified end
    uses. 
[5] Colors: White
    Number of Coats: 1-3
    Maximum Field Use Dry Thickness (in mils): 18 mils
    Maximum Thinner: 15% water
    Recoat Cure Time and Temperature: 6 hours at 75F
    Final Cure Time/Temperature: 7 days at 75F
    Special Comments: Series 44-700 Accelerator may be added up to 1 fl. oz./gal. Series
    1220 Tnemec Epoxy is approved for use as a primer or topcoat with any NSF Certified
    Tnemec topcoat or coating system providing that both primer and topcoat meet their
    individual Certified end uses. Mix ratio of Part A:Part B is 2:1 by volume.
[6] Colors: WH16 Off-White, 1255 Beige, 39BL Delft Blue, B5712 Westech Blue, 11SF True
    Blue/Safety, 1211 Red Primer, A13096 Baker Dark Gray, B2592 RAL5009 Azurblau, B2506
    Dezurik Blue, B9918 New Baker Blue
    Number of Coats: 2
    Maximum Field Use Dry Thickness(in mils): 20 mils
    Maximum Thinner: None
    Recoat Cure Time and Temperature: 16 hours at 75F
    Final Cure Time/Temperature: 30 days at 75F
    Special Comments: Mix ratio of A:B is 2:1 by volume. This is for pipe, fitting, pump and
    valve end use.
[7] Colors: WH16 OFF-WHITE, 35GR Black, 33GR Gray, 39BL Delft Blue, 1255 Beige, B5712
    Westech Blue, 11SF True Blue/Safety, 1211 Red Primer, A13096 Baker Dark Gray, B2592
    RAL5009 Azurblau, B2506 Dezurik Blue, B9918 New Baker Blue
    Number of Coats: 1-3
    Maximum Field Use Dry Thickness(in mils): 20
    Maximum Thinner: 5% F041-0088 Thinner Clear by volume
    Recoat Cure Time and Temperature: 8 hours at 75F
    Final Cure Time/Temperature: 7 days at 75F
    Special Comments: Mix ratio of A:B is 2:1 by volume. Series 21 Epoxoline is approved for
    use as a primer or topcoat with any NSF Certified Tnemec topcoat or coating system
    providing that both primer and topcoat meet their individual Certified end uses.
[8] Colors: Greenish-gray
    Number of Coats: 1
    Maximum Field Use Dry Film Thickness (in mils): 4
    Maximum Thinner: 10% Thinner No. 2 or 10% Thinner No. 3 by volume
    Final Cure Time and Temperature: 4 hours at 75°F; 2 hours at 75°F when the accelerator
    is used 
    Special Comments: Series 44-710 Urethane Accelerator may be added up to 4 fl. oz/gal. 
    Series 91-H2O™ Hydro-Zinc™ is approved for use with any NSF Certified Tnemec topcoat or
    coating system providing that both primer and topcoat meet their individual Certified
    end uses.  Mix ratio of Part A:Part B is 70%:30% by volume.
[9] This coating used with Thinner #2 is Certified for use in pipes >=96", tanks >=50,000
    gallons, fittings >=1", pumps >=1", and valves >=4".
[10] This coatings used with Thinner #3 is Certified for use in pipes >=96", tanks >=40,000
     gallons, fittings >=1", pumps >=1/2", and valves >=1.75".
[11] Colors: Greenish-Gray
     Maximum Field Use Dry Thickness(in mils): 4 mils
     Maximum Thinner: 10% Thinner #2 by volume
     Final Cure Time/Temperature: 8 hours at 75F. 4 hours at 75F if accelerator is used. 
     Special Comments: Series 44-710 accelerator may be used up to 4 fluid oz/gal. 93-H20
     Hydro-Zinc is approved for use with any NSF Certified Tnemec topcoat or coating system
     providing that both primer and topcoat meet their individual Certified end uses.
[12] Color: Greenish-Gray
     Number of Coats: 1
     Maximum Field Use Dry Film Thickness (in mils): 4
     Maximum Thinner: 15% Tnemec No. 49 by volume or 10% Thinner No. 3 or 10% Thinner No. 2
     Recoat Cure Time and Temperature: 8 hours at 75°F; 2 hours at 75°F when the accelerator
     is used  
     Special Comments: Series 44-710 may be added up to 4 fl. oz/gal. 94-H2O is approved for
     use with any NSF Certified Tnemec topcoat or coating system.
[14] Colors: WH08 White, R4875A Akzo Red, B8869A Epoxoline Blue
     Number of Coats: 1
     Sequence of Coats: N/A
     Maximum Field Use Dry Film Thickness (in mils): 80
     Maximum Thinner: None
     Final Cure Time and Temperature: 24 hours at 75°F
     Special Comments: Mix ratio of Part A:Part B is 1:2 by volume.  Any Listed color of
     series N140 or N140F may be used as a topcoat or primer for Series FC22 Epoxoline.
[17] Colors: 00WH Tnemec White, 1211 Red, 1255 Beige, 15BL Tank white, 35GR Black, 39BL Delft
     blue, B5712 Westech Blue, 11SF True Blue, B9118 Baker Blue, B8314 Krausz Blue, Y2606
     Romac Yellow, B2592 RAL 5009 Azurblau, B7011 Crispin Blue, B2506 Dezurik Blue, B9695
     Houston Blue, A14130 Mueller Gray, R5477 Mueller Sienna Red.
     Number of Coats: 1
     Maximum Field Use Dry Thickness(in mils): 4 mils
     Maximum Thinner: 10% No. 4 Thinner by volume
     Recoat Cure Time and Temperature: 5 hours at 75°F
     Final Cure Time and Temperature: 7 days at 75°F (entire system)
     Special Comments: Mix ratio is 1 Part A to 1 Part B by volume. Certified for use
     as an optional primer or intermediate coat with any Tnemec NSF certified primer
     and topcoat coating system provided the primer, intermediate, and topcoat meet
     their certified end uses. Part C (Series 44-700 Accelerator) is an optional additive to
     Part A in the field and may be added at up to 4 fluid ounces per gallon of Part A.
[18] Meets the health effects requirements of NSF/ANSI/CAN 600 according to requirements of
     NSF/ANSI/CAN 61 for pump, valve, and fitting end use.
[19] Colors: 00WH Tnemec White, 1211 Red, 1255 Beige, 15BL Tank White, 35GR Black, 39BL Delft
     Blue, B2506 DeZurik Blue, B5712 Westech Blue, 11SF True Blue, B9118 Baker Blue, B7896
     S-B Blue, Y2606 Romac Yellow, B2592 RAL 5009 Azurblau, B7011 Crispin Blue, B9695 Houston
     Blue, A14130 Mueller Gray, R5477 Mueller Sienna Red.
     Number of Coats: 2-3
     Sequence of Coats: Any combination of Listed colors
     Maximum Field Use Dry Film Thickness (in mils): 18
     Maximum Thinner: 5% Tnemec No. 60 Thinner by volume
     Recoat Cure Time and Temperature: 5 hours at 75°F
     Final Cure Time and Temperature: 30 days at 75°F
     Special comments: Any listed color of Series 22, FC22, N140 or 141 may be substituted as
     a primer of topcoat for Series N140 Pota-Pox Plus provided that both primer and topcoat
     meet their individual Certified end uses.  The mix ratio of Part A:Part B is 1:1 by
     volume.
[22] Colors: 00WH Tnemec White, 1211 Red, 1255 Beige, 15BL Tank White, 35GR Black, 39BL Delft
     Blue, B5712 Westech Blue, 11SF True Blue, B9118 Baker Blue, B8314 Krausz Blue, A13096
     Baker Dark Gray, Y2606 Romac Yellow, B2592 RAL 5009 Azurblau, B7011 Crispin Blue, B2506
     Dezurik Blue, B9695 Houston Blue, A14130 Mueller Gray, R5477 Mueller Sienna Red.
     Number of Coats: 2-3
     Sequence of Coats: Any combination of Listed colors
     Maximum Field Use Dry Film Thickness (in mils): 18
     Maximum Thinner: 5% Tnemec No. 60 Thinner by volume
     Recoat Cure Time and Temperature: 5 hours at 75°F with accelerator, 9 hours at 75°F
     without accelerator
     Final Cure Time and Temperature: 30 days at 75°F
     Special Comments: Any Listed color of Series 22, FC22, N140, or 141 may be substituted
     as a primer of topcoat for Series N140 Pota-Pox Plus provided that both primer and
     topcoat meet their individual Certified end uses.  The mix ratio of Part A:Part B is 1:1
     by volume.  Part C (Series 44-700 Accelerator) is an optional addititve to Part A in the
     field and may be added at up to 4 fluid ounces per two mixed gallons of parts A and B.
[23] This coating used with Thinner #49 is Certified for use in pumps >= ¾”. This coating
     used with Thinner #2 is Certified for use in pumps >= 1”. This coating used with Thinner
     #3 is Certified for use in pumps >= ½”.

Coatings - Tank
22 Epoxoline[1] [2] >= 700 gal. CLD 23 EPOXY
F098-0H20 Hydro-Zinc[2] [3] >= 70,000 gal. CLD 23 EPOXY
N140F Pota-Pox Plus Fast Cure[2] [4] >= 4,000 gal. CLD 23 EPOXY
Series 1 Omnithane 1216 Greenish-Gray[2] [20] >= 1000 gal. CLD 23 PUR
Series 1220 Tnemec Epoxy[2] [5] >= 200 gal. CLD 23 EPOXY
Series 21 Epoxoline[2] [7] >= 1,500 gal. CLD 23 EPOXY
Series 215[2] [24] >= 200 gal. CLD 23 EPOXY
Series 215ML[2] [24] >= 200 gal. CLD 23 EPOXY
Series 91-H2O ™ Hydro-Zinc™ [2] [8] [10] >= 40,000 gal. CLD 23 PUR
Series 91-H2O™ Hydro-Zinc™[2] [8] [9] >= 50,000 gal. CLD 23 PUR
Series 93-H20 Hydro-Zinc [11] >= 50,000 gal CLD 23 PUR
Series 94-H2O Hydro Zinc[2] [12] [25] CLD 23 PUR
Series FC22 Epoxoline[2] [26] >= 200 gal. CLD 23 EPOXY
Series L140 Pota-Pox Plus[2] [15] >= 50,000 gal. CLD 23 EPOXY
Series L140F Pota-Pox Plus Fast Cure[2] [16] >= 50,000 gal. CLD 23 EPOXY
Series N140 Pota-Pox Plus[2] [17] >= 4,000 gal. CLD 23 EPOXY

[1] Colors: 1255 Beige, 1218 Blue, WH11 White
    Number of Coats: 1-2
    Maximum Field Use Dry Film Thickness (in mils): 50
    Maximum Thinner: 5% Thinner #2
    Recoat Cure Time and Temperature: 16 hours at 75°F 
    Final Cure Time and Temperature: 5 days at 75°F
    Special Comments: Mix ratio of Part A to Part B is 1:1 by volume.  Optional use with
    fiberglass flake S211-0220.  The fiberglass flake can be added up to a rate of 1% by
    weight after the Parts A and B are mixed together.  Certified for use as a primer or
    topcoat with any NSF Certified Tnemec coating system provided that both primer and
    topcoat meet their individual certified end uses.
[2] Meets the health effects requirements of NSF/ANSI/CAN 600 according to the requirements
    of NSF/ANSI/CAN 61 including the most current health effects criteria for xylenes,
    toluene, and ethylbenzene. 
[3] Colors: Greenish Gray
    Number of Coats: 1
    Maximum Field Use Dry Thickness (in mils): 4mils
    Maximum Thinner: 25% Water
    Recoat Cure Time and Temperature: 5 hours at 75F
    Final Cure Time/Temperature: 7 days at 75F
    Special Comments: Series 44-780 Accelerator may be added up to 1 fl. oz/gal. Series
    98-H2O Hydro-Zinc is approved for use as a primer with any NSF Certified Tnemec topcoat
    or coating system providing that both primer and topcoat meet their individual Certified
    end uses. Cure for Series 98-H2O Hydro-Zinc primer is 5 hours at 75F. Top-coat is then
    applied. Final cure is 7 days. Mix ratio of Part A:B:C is 1.4:0.6:1 by volume.
[4] Colors: 15BL Tank White, 1255 Beige, 1211 Red, 35GR Black, 39BL Delft Blue, Y2606 Romac
    Yellow, 00WH Tnemec White, 11SF True Blue, B9118 Baker Blue, B5712 Westech Blue, B2592
    RAL 5009 Azurblau,  B9695 Houston Blue, A14130 Mueller Gray, R5477 Mueller Sienna Red.
    Number of Coats: 1
    Sequence of Coats: 4 mils
    Maximum Thinner: 10% No. 4 Thinner by volume
    Recoat Cure Time and Temperature: 5 hours at 75F
    Final Cure Time/Temperature: 7 days at 75F (entire system)
    Special Comments: Mix ration is 1 Part A to 1 Part B by volume. Certified for use as an
    optional primer or intermediate topcoat with any Tnemec NSF certified primer and topcoat
    coating system provided the primer, intermediate, and topcoat meet their certified end
    uses. 
[5] Colors: White
    Number of Coats: 1-3
    Maximum Field Use Dry Thickness (in mils): 18 mils
    Maximum Thinner: 15% water
    Recoat Cure Time and Temperature: 6 hours at 75F
    Final Cure Time/Temperature: 7 days at 75F
    Special Comments: Series 44-700 Accelerator may be added up to 1 fl. oz./gal. Series
    1220 Tnemec Epoxy is approved for use as a primer or topcoat with any NSF Certified
    Tnemec topcoat or coating system providing that both primer and topcoat meet their
    individual Certified end uses. Mix ratio of Part A:Part B is 2:1 by volume.
[7] Colors: WH16 OFF-WHITE, 35GR Black, 33GR Gray, 39BL Delft Blue, 1255 Beige, B5712
    Westech Blue, 11SF True Blue/Safety, 1211 Red Primer, A13096 Baker Dark Gray, B2592
    RAL5009 Azurblau, B2506 Dezurik Blue, B9918 New Baker Blue
    Number of Coats: 1-3
    Maximum Field Use Dry Thickness(in mils): 20
    Maximum Thinner: 5% F041-0088 Thinner Clear by volume
    Recoat Cure Time and Temperature: 8 hours at 75F
    Final Cure Time/Temperature: 7 days at 75F
    Special Comments: Mix ratio of A:B is 2:1 by volume. Series 21 Epoxoline is approved for
    use as a primer or topcoat with any NSF Certified Tnemec topcoat or coating system
    providing that both primer and topcoat meet their individual Certified end uses.
[8] Colors: Greenish-gray
    Number of Coats: 1
    Maximum Field Use Dry Film Thickness (in mils): 4
    Maximum Thinner: 10% Thinner No. 2 or 10% Thinner No. 3 by volume
    Final Cure Time and Temperature: 4 hours at 75°F; 2 hours at 75°F when the accelerator
    is used 
    Special Comments: Series 44-710 Urethane Accelerator may be added up to 4 fl. oz/gal. 
    Series 91-H2O™ Hydro-Zinc™ is approved for use with any NSF Certified Tnemec topcoat or
    coating system providing that both primer and topcoat meet their individual Certified
    end uses.  Mix ratio of Part A:Part B is 70%:30% by volume.
[9] This coating used with Thinner #2 is Certified for use in pipes >=96", tanks >=50,000
    gallons, fittings >=1", pumps >=1", and valves >=4".
[10] This coatings used with Thinner #3 is Certified for use in pipes >=96", tanks >=40,000
     gallons, fittings >=1", pumps >=1/2", and valves >=1.75".
[11] Colors: Greenish-Gray
     Maximum Field Use Dry Thickness(in mils): 4 mils
     Maximum Thinner: 10% Thinner #2 by volume
     Final Cure Time/Temperature: 8 hours at 75F. 4 hours at 75F if accelerator is used. 
     Special Comments: Series 44-710 accelerator may be used up to 4 fluid oz/gal. 93-H20
     Hydro-Zinc is approved for use with any NSF Certified Tnemec topcoat or coating system
     providing that both primer and topcoat meet their individual Certified end uses.
[12] Color: Greenish-Gray
     Number of Coats: 1
     Maximum Field Use Dry Film Thickness (in mils): 4
     Maximum Thinner: 15% Tnemec No. 49 by volume or 10% Thinner No. 3 or 10% Thinner No. 2
     Recoat Cure Time and Temperature: 8 hours at 75°F; 2 hours at 75°F when the accelerator
     is used  
     Special Comments: Series 44-710 may be added up to 4 fl. oz/gal. 94-H2O is approved for
     use with any NSF Certified Tnemec topcoat or coating system.
[15] Colors: 00WH White, 1211 Red, 1255 Beige, 15BL Tank White
     Number of Coats: 2-3
     Sequence of Coats: Any combination of Listed colors
     Maximum Field Use Dry Film Thickness (in mils): 18 (maximum of 6 mils per coat)
     Maximum Thinner: 5% Tnemec No. 49 Thinner by volume
     Recoat Cure Time and Temperature: 16 hours at 75°F
     Final Cure Time and Temperature: 7 days at 75°F
     Special Comments: Series N140, N140F, V140, V140F, L140 and Series 22, FC22 may be
     substituted as a primer or topcoat for L140 provided that both primer and topcoat meet
     their individual Certified end uses. Series 44-700 accelerator (Part C) may be added up
     to 4 fluid ounces per two mixed gallons of L140 Parts A and B. Mix ratio of A:B is 1:1
     by volume.
[16] Colors: 1255 Beige, 15BL Tank White, 1211 Red, 00WH White
     Number of Coats: 2-3
     Sequence of coats: Any combination of Listed colors
     Maximum Field Use Dry Film Thickness (in mils): 18 (maximum of 6 mils per coat)
     Maximum Thinner: 5% Tnemec No. 49 by volume
     Recoat Cure Time and Temperature: 16 hours at 75°F
     Final Cure Time and Temperature: 7 days at 75°F
     Special Comments: Series N140, N140F, V140, V140F, L140 and Series 22, FC22 may be
     substituted as a primer or topcoat for L140F provided that both primer and topcoat meet
     their individual Certified end uses. Mix ratio of Part A to Part B is 1:1 by volume.
[17] Colors: 00WH Tnemec White, 1211 Red, 1255 Beige, 15BL Tank white, 35GR Black, 39BL Delft
     blue, B5712 Westech Blue, 11SF True Blue, B9118 Baker Blue, B8314 Krausz Blue, Y2606
     Romac Yellow, B2592 RAL 5009 Azurblau, B7011 Crispin Blue, B2506 Dezurik Blue, B9695
     Houston Blue, A14130 Mueller Gray, R5477 Mueller Sienna Red.
     Number of Coats: 1
     Maximum Field Use Dry Thickness(in mils): 4 mils
     Maximum Thinner: 10% No. 4 Thinner by volume
     Recoat Cure Time and Temperature: 5 hours at 75°F
     Final Cure Time and Temperature: 7 days at 75°F (entire system)
     Special Comments: Mix ratio is 1 Part A to 1 Part B by volume. Certified for use
     as an optional primer or intermediate coat with any Tnemec NSF certified primer
     and topcoat coating system provided the primer, intermediate, and topcoat meet
     their certified end uses. Part C (Series 44-700 Accelerator) is an optional additive to
     Part A in the field and may be added at up to 4 fluid ounces per gallon of Part A.
[20] Colors: 1216 Greenish-Gray
     Number of Coats: 1
     Sequence of Coats: N/A
     Maximum Field Use Dry Film Thickness (in mils): 4
     Maximum Thinner: 10% Thinner No. 2
     Recoat Cure Time and Temperature: 8 hours at 75°F
     Special Comment: Series 44-710 may be added up to 4 fl. oz/gal. Approved for use as a
     primer with any NSF Certified Tnemec topcoat or coating system provided that both primer
     and topcoat meet their individual Certified end uses.
[24] Colors: 1200 White, 1212 Gray
     Number of Coats: 1
     Maximum Field Use Dry Film Thickness (in mils): Coating only: 80; With fiberglass mat:
     95
     Final Cure Time and Temperature: 7 days at 75°F
     Special Comments: Mix ratio of Part A to Part B is 1:1 by volume. Optional use with
     fiberglass mat S211-0215, S211-0216, and/or addition of fumed silica S211-0211 to
     coating. Mix ratio for fumed silica is 0.75:1 by volume. Approved for use with any NSF
     Certified Tnemec topcoat or coating system provided that both primer and topcoat meet
     their individual Certified end uses.
[25] This coating used with Thinner #49 is Certified for use in tanks >= 1,500 gallons. This
     coating used with Thinner #2 is Certified for use in tanks >= 50,000 gallons. This
     coating used with Thinner #3 is Certified for use in tanks >= 40,000 gallons.
[26] Colors: WH08 White, 35GR Epoxoline Black, R4875A Akzo Red, B8869A Epoxoline Blue
     Number of Coats: 1
     Sequence of Coats: N/A
     Maximum Field Use Dry Film Thickness (in mils): 80
     Maximum Thinner: None
     Final Cure Time and Temperature: 24 hours at 75° F
     Special Comments: Mix ratio of part A:Part B is 1:2 by volume.  Any Listed color of
     Series F020, FC20, L140, L140F, N140, N140F, V140, or V140F may be used as a topcoat or
     primer for SeriesFC22 Epoxoline.

Coatings - Valve
22 Epoxoline[1] [2] >= 4" CLD 23 EPOXY
F098-0H20 Hydro-Zinc[2] [3] >= 4" CLD 23 EPOXY
N140F Pota-Pox Plus Fast Cure[2] [4] >= 4" CLD 23 EPOXY
Series 1 Omnithane 1216 Greenish-Gray[2] [20] >= 4" CLD 23 PUR
Series 1220 Tnemec Epoxy[2] [5] >= 1 1/2" CLD 23 EPOXY
Series 21 Epoxoline[2] [7] >= 4" CLD 23 EPOXY
Series 21 Epoxoline [2] [6] >= 1/2" CLD 23 EPOXY
Series 91-H2O ™ Hydro-Zinc™[2] [8] [10] >= 1 3/4" CLD 23 EPOXY
Series 91-H2O™ Hydro-Zinc™[2] [8] [9] >= 4" CLD 23 PUR
Series 93-H20 Hydro-Zinc[11] >= 4" CLD 23 PUR
Series 94-H2O Hydro-Zinc[2] [12] [27] CLD 23 PUR
Series FC22 Epoxoline[2] [14] >= 2" CLD 23 EPOXY
Series N140 Pota-Pox Plus[18] [22] >= 4" CLD 23 EPOXY
Series N140 Pota-Pox Plus [2] [17] >= 4" CLD 23 EPOXY
Series N140F Pota-Pox Plus Fast Cure[18] [19] >= 4" CLD 23 EPOXY

[1] Colors: 1255 Beige, 1218 Blue, WH11 White
    Number of Coats: 1-2
    Maximum Field Use Dry Film Thickness (in mils): 50
    Maximum Thinner: 5% Thinner #2
    Recoat Cure Time and Temperature: 16 hours at 75°F 
    Final Cure Time and Temperature: 5 days at 75°F
    Special Comments: Mix ratio of Part A to Part B is 1:1 by volume.  Optional use with
    fiberglass flake S211-0220.  The fiberglass flake can be added up to a rate of 1% by
    weight after the Parts A and B are mixed together.  Certified for use as a primer or
    topcoat with any NSF Certified Tnemec coating system provided that both primer and
    topcoat meet their individual certified end uses.
[2] Meets the health effects requirements of NSF/ANSI/CAN 600 according to the requirements
    of NSF/ANSI/CAN 61 including the most current health effects criteria for xylenes,
    toluene, and ethylbenzene. 
[3] Colors: Greenish Gray
    Number of Coats: 1
    Maximum Field Use Dry Thickness (in mils): 4mils
    Maximum Thinner: 25% Water
    Recoat Cure Time and Temperature: 5 hours at 75F
    Final Cure Time/Temperature: 7 days at 75F
    Special Comments: Series 44-780 Accelerator may be added up to 1 fl. oz/gal. Series
    98-H2O Hydro-Zinc is approved for use as a primer with any NSF Certified Tnemec topcoat
    or coating system providing that both primer and topcoat meet their individual Certified
    end uses. Cure for Series 98-H2O Hydro-Zinc primer is 5 hours at 75F. Top-coat is then
    applied. Final cure is 7 days. Mix ratio of Part A:B:C is 1.4:0.6:1 by volume.
[4] Colors: 15BL Tank White, 1255 Beige, 1211 Red, 35GR Black, 39BL Delft Blue, Y2606 Romac
    Yellow, 00WH Tnemec White, 11SF True Blue, B9118 Baker Blue, B5712 Westech Blue, B2592
    RAL 5009 Azurblau,  B9695 Houston Blue, A14130 Mueller Gray, R5477 Mueller Sienna Red.
    Number of Coats: 1
    Sequence of Coats: 4 mils
    Maximum Thinner: 10% No. 4 Thinner by volume
    Recoat Cure Time and Temperature: 5 hours at 75F
    Final Cure Time/Temperature: 7 days at 75F (entire system)
    Special Comments: Mix ration is 1 Part A to 1 Part B by volume. Certified for use as an
    optional primer or intermediate topcoat with any Tnemec NSF certified primer and topcoat
    coating system provided the primer, intermediate, and topcoat meet their certified end
    uses. 
[5] Colors: White
    Number of Coats: 1-3
    Maximum Field Use Dry Thickness (in mils): 18 mils
    Maximum Thinner: 15% water
    Recoat Cure Time and Temperature: 6 hours at 75F
    Final Cure Time/Temperature: 7 days at 75F
    Special Comments: Series 44-700 Accelerator may be added up to 1 fl. oz./gal. Series
    1220 Tnemec Epoxy is approved for use as a primer or topcoat with any NSF Certified
    Tnemec topcoat or coating system providing that both primer and topcoat meet their
    individual Certified end uses. Mix ratio of Part A:Part B is 2:1 by volume.
[6] Colors: WH16 Off-White, 1255 Beige, 39BL Delft Blue, B5712 Westech Blue, 11SF True
    Blue/Safety, 1211 Red Primer, A13096 Baker Dark Gray, B2592 RAL5009 Azurblau, B2506
    Dezurik Blue, B9918 New Baker Blue
    Number of Coats: 2
    Maximum Field Use Dry Thickness(in mils): 20 mils
    Maximum Thinner: None
    Recoat Cure Time and Temperature: 16 hours at 75F
    Final Cure Time/Temperature: 30 days at 75F
    Special Comments: Mix ratio of A:B is 2:1 by volume. This is for pipe, fitting, pump and
    valve end use.
[7] Colors: WH16 OFF-WHITE, 35GR Black, 33GR Gray, 39BL Delft Blue, 1255 Beige, B5712
    Westech Blue, 11SF True Blue/Safety, 1211 Red Primer, A13096 Baker Dark Gray, B2592
    RAL5009 Azurblau, B2506 Dezurik Blue, B9918 New Baker Blue
    Number of Coats: 1-3
    Maximum Field Use Dry Thickness(in mils): 20
    Maximum Thinner: 5% F041-0088 Thinner Clear by volume
    Recoat Cure Time and Temperature: 8 hours at 75F
    Final Cure Time/Temperature: 7 days at 75F
    Special Comments: Mix ratio of A:B is 2:1 by volume. Series 21 Epoxoline is approved for
    use as a primer or topcoat with any NSF Certified Tnemec topcoat or coating system
    providing that both primer and topcoat meet their individual Certified end uses.
[8] Colors: Greenish-gray
    Number of Coats: 1
    Maximum Field Use Dry Film Thickness (in mils): 4
    Maximum Thinner: 10% Thinner No. 2 or 10% Thinner No. 3 by volume
    Final Cure Time and Temperature: 4 hours at 75°F; 2 hours at 75°F when the accelerator
    is used 
    Special Comments: Series 44-710 Urethane Accelerator may be added up to 4 fl. oz/gal. 
    Series 91-H2O™ Hydro-Zinc™ is approved for use with any NSF Certified Tnemec topcoat or
    coating system providing that both primer and topcoat meet their individual Certified
    end uses.  Mix ratio of Part A:Part B is 70%:30% by volume.
[9] This coating used with Thinner #2 is Certified for use in pipes >=96", tanks >=50,000
    gallons, fittings >=1", pumps >=1", and valves >=4".
[10] This coatings used with Thinner #3 is Certified for use in pipes >=96", tanks >=40,000
     gallons, fittings >=1", pumps >=1/2", and valves >=1.75".
[11] Colors: Greenish-Gray
     Maximum Field Use Dry Thickness(in mils): 4 mils
     Maximum Thinner: 10% Thinner #2 by volume
     Final Cure Time/Temperature: 8 hours at 75F. 4 hours at 75F if accelerator is used. 
     Special Comments: Series 44-710 accelerator may be used up to 4 fluid oz/gal. 93-H20
     Hydro-Zinc is approved for use with any NSF Certified Tnemec topcoat or coating system
     providing that both primer and topcoat meet their individual Certified end uses.
[12] Color: Greenish-Gray
     Number of Coats: 1
     Maximum Field Use Dry Film Thickness (in mils): 4
     Maximum Thinner: 15% Tnemec No. 49 by volume or 10% Thinner No. 3 or 10% Thinner No. 2
     Recoat Cure Time and Temperature: 8 hours at 75°F; 2 hours at 75°F when the accelerator
     is used  
     Special Comments: Series 44-710 may be added up to 4 fl. oz/gal. 94-H2O is approved for
     use with any NSF Certified Tnemec topcoat or coating system.
[14] Colors: WH08 White, R4875A Akzo Red, B8869A Epoxoline Blue
     Number of Coats: 1
     Sequence of Coats: N/A
     Maximum Field Use Dry Film Thickness (in mils): 80
     Maximum Thinner: None
     Final Cure Time and Temperature: 24 hours at 75°F
     Special Comments: Mix ratio of Part A:Part B is 1:2 by volume.  Any Listed color of
     series N140 or N140F may be used as a topcoat or primer for Series FC22 Epoxoline.
[17] Colors: 00WH Tnemec White, 1211 Red, 1255 Beige, 15BL Tank white, 35GR Black, 39BL Delft
     blue, B5712 Westech Blue, 11SF True Blue, B9118 Baker Blue, B8314 Krausz Blue, Y2606
     Romac Yellow, B2592 RAL 5009 Azurblau, B7011 Crispin Blue, B2506 Dezurik Blue, B9695
     Houston Blue, A14130 Mueller Gray, R5477 Mueller Sienna Red.
     Number of Coats: 1
     Maximum Field Use Dry Thickness(in mils): 4 mils
     Maximum Thinner: 10% No. 4 Thinner by volume
     Recoat Cure Time and Temperature: 5 hours at 75°F
     Final Cure Time and Temperature: 7 days at 75°F (entire system)
     Special Comments: Mix ratio is 1 Part A to 1 Part B by volume. Certified for use
     as an optional primer or intermediate coat with any Tnemec NSF certified primer
     and topcoat coating system provided the primer, intermediate, and topcoat meet
     their certified end uses. Part C (Series 44-700 Accelerator) is an optional additive to
     Part A in the field and may be added at up to 4 fluid ounces per gallon of Part A.
[18] Meets the health effects requirements of NSF/ANSI/CAN 600 according to requirements of
     NSF/ANSI/CAN 61 for pump, valve, and fitting end use.
[19] Colors: 00WH Tnemec White, 1211 Red, 1255 Beige, 15BL Tank White, 35GR Black, 39BL Delft
     Blue, B2506 DeZurik Blue, B5712 Westech Blue, 11SF True Blue, B9118 Baker Blue, B7896
     S-B Blue, Y2606 Romac Yellow, B2592 RAL 5009 Azurblau, B7011 Crispin Blue, B9695 Houston
     Blue, A14130 Mueller Gray, R5477 Mueller Sienna Red.
     Number of Coats: 2-3
     Sequence of Coats: Any combination of Listed colors
     Maximum Field Use Dry Film Thickness (in mils): 18
     Maximum Thinner: 5% Tnemec No. 60 Thinner by volume
     Recoat Cure Time and Temperature: 5 hours at 75°F
     Final Cure Time and Temperature: 30 days at 75°F
     Special comments: Any listed color of Series 22, FC22, N140 or 141 may be substituted as
     a primer of topcoat for Series N140 Pota-Pox Plus provided that both primer and topcoat
     meet their individual Certified end uses.  The mix ratio of Part A:Part B is 1:1 by
     volume.
[20] Colors: 1216 Greenish-Gray
     Number of Coats: 1
     Sequence of Coats: N/A
     Maximum Field Use Dry Film Thickness (in mils): 4
     Maximum Thinner: 10% Thinner No. 2
     Recoat Cure Time and Temperature: 8 hours at 75°F
     Special Comment: Series 44-710 may be added up to 4 fl. oz/gal. Approved for use as a
     primer with any NSF Certified Tnemec topcoat or coating system provided that both primer
     and topcoat meet their individual Certified end uses.
[22] Colors: 00WH Tnemec White, 1211 Red, 1255 Beige, 15BL Tank White, 35GR Black, 39BL Delft
     Blue, B5712 Westech Blue, 11SF True Blue, B9118 Baker Blue, B8314 Krausz Blue, A13096
     Baker Dark Gray, Y2606 Romac Yellow, B2592 RAL 5009 Azurblau, B7011 Crispin Blue, B2506
     Dezurik Blue, B9695 Houston Blue, A14130 Mueller Gray, R5477 Mueller Sienna Red.
     Number of Coats: 2-3
     Sequence of Coats: Any combination of Listed colors
     Maximum Field Use Dry Film Thickness (in mils): 18
     Maximum Thinner: 5% Tnemec No. 60 Thinner by volume
     Recoat Cure Time and Temperature: 5 hours at 75°F with accelerator, 9 hours at 75°F
     without accelerator
     Final Cure Time and Temperature: 30 days at 75°F
     Special Comments: Any Listed color of Series 22, FC22, N140, or 141 may be substituted
     as a primer of topcoat for Series N140 Pota-Pox Plus provided that both primer and
     topcoat meet their individual Certified end uses.  The mix ratio of Part A:Part B is 1:1
     by volume.  Part C (Series 44-700 Accelerator) is an optional addititve to Part A in the
     field and may be added at up to 4 fluid ounces per two mixed gallons of parts A and B.
[27] This coating used with Thinner #49 is Certified for use in valves >= ¾”. This coating
     used with Thinner #2 is Certified for use in valves >= 4”. This coating used with
     Thinner #3 is Certified for use in valves >= 1.75”.



Facility : Jinshan District, Shanghai, China

Protective (Barrier) Materials

    Water Water
  Water Contact Contact Contact
Trade Designation Size Restriction Temp Material

Coatings - Fittings[1]
Series N140 Pota-Pox Plus[2] >= 8" CLD 23 EPOXY
Series N140F Pota-Pox Plus Fast Cure[3] >= 8" CLD 23 EPOXY

[1] Meets the health effects requirements of NSF/ANSI/CAN 600 according to requirements of
    NSF/ANSI/CAN 61 for pump, valve, and fitting end use.
[2] Colors: 1211 Red, 1255 Beige,15BL Tank White, 39BL Delft Blue, 35GR Black, 00WH Tnemec
    White, Y2606 Romac Yellow, B8314 Krausz Blue, B5712 Westech Blue, 11SF True Blue, B9118
    Baker Blue, A13096 Baker Dark Gray, B2592 RAL 5009 Azurblau, B7011 Crispin Blue, B2506
    Dezurik Blue,  A14130 Mueller Gray, B9695 Houston Blue, R5477 Mueller Sienna Red.
    Number of Coats: 2-3
    Sequence of Coats: Any combination of Listed colors
    Maximum Field Use Dry Film Thickness (in mils): 18
    Maximum Thinner: 5% Tnemec No. 60 Thinner by volume
    Recoat Cure Time and Temperature: 5 hours at 75°F with accelerator, 9 hours at 75°F
    without accelerator
    Final Cure Time and Temperature: 30 days at 75°F
    Special Comments: Any listed color of Series 22, FC22, N140, or 141 may be substituted
    as a primer of topcoat for Series N140 Pota-Pox Plus provided that both primer and
    topcoat meet their individual Certified end uses. The mix ratio of Part A: Part B is 1:1
    by volume. Part C (Series 44-700 Accelerator) is an optional additive to Part A in the
    field and may be added at up to 4 fluid ounces per two mixed gallons of parts A and B.
[3] Colors: 1211 Red, 1255 Beige, B2506 DeZurik Blue, 15BL Tank White, 39BL Delft Blue, 35GR
    Black, 00WH Tnemec White, B7896 S-B Blue, Y2606 Romac Yellow, B5712 Blue, B2592 RAL 5009
    Azurblau, B7011 Crispin Blue, B9695 Houston Blue, A14130 Mueller Gray, R5477 Mueller
    Sienna Red.
    Number of Coats: 2
    Sequence of Coats: Any combination of Listed colors
    Maximum Field Use Dry film Thickness (in mils): 18
    Maximum Thinner: 5% Tnemec No. 60 Thinner by volume
    Recoat Cure Time and Temperature: 5 hours at 75°F 
    Final Cure Time and Temperature: 30 days at 75°F
    Special Comments: Any listed color of Series 22, FC22, N140, or 141 may be substituted
    as a primer of topcoat for Series N140 Pota-Pox Plus provided that both primer and
    topcoat meet their individual Certified end uses. The mix ratio of Part A: Part B is 1:1
    by volume.

Coatings - Mechanical Devices[1]
Series N140 Pota-Pox Plus [2] [4] CLD 23 EPOXY

[1] Meets the health effects requirements of NSF/ANSI/CAN 600 according to requirements of
    NSF/ANSI/CAN 61 for pump, valve, and fitting end use.
[2] Colors: 1211 Red, 1255 Beige,15BL Tank White, 39BL Delft Blue, 35GR Black, 00WH Tnemec
    White, Y2606 Romac Yellow, B8314 Krausz Blue, B5712 Westech Blue, 11SF True Blue, B9118
    Baker Blue, A13096 Baker Dark Gray, B2592 RAL 5009 Azurblau, B7011 Crispin Blue, B2506
    Dezurik Blue,  A14130 Mueller Gray, B9695 Houston Blue, R5477 Mueller Sienna Red.
    Number of Coats: 2-3
    Sequence of Coats: Any combination of Listed colors
    Maximum Field Use Dry Film Thickness (in mils): 18
    Maximum Thinner: 5% Tnemec No. 60 Thinner by volume
    Recoat Cure Time and Temperature: 5 hours at 75°F with accelerator, 9 hours at 75°F
    without accelerator
    Final Cure Time and Temperature: 30 days at 75°F
    Special Comments: Any listed color of Series 22, FC22, N140, or 141 may be substituted
    as a primer of topcoat for Series N140 Pota-Pox Plus provided that both primer and
    topcoat meet their individual Certified end uses. The mix ratio of Part A: Part B is 1:1
    by volume. Part C (Series 44-700 Accelerator) is an optional additive to Part A in the
    field and may be added at up to 4 fluid ounces per two mixed gallons of parts A and B.
[4] Certified for mechanical device end use (other than pump and valve) for a maximum of 4.6
    sq. ft. per gpm.

Coatings - Pump[1]
Series N140 Pota-Pox Plus[2] >= 4" CLD 23 EPOXY
Series N140F Pota-Pox Plus Fast Cure[3] >= 4" CLD 23 EPOXY

[1] Meets the health effects requirements of NSF/ANSI/CAN 600 according to requirements of
    NSF/ANSI/CAN 61 for pump, valve, and fitting end use.
[2] Colors: 1211 Red, 1255 Beige,15BL Tank White, 39BL Delft Blue, 35GR Black, 00WH Tnemec
    White, Y2606 Romac Yellow, B8314 Krausz Blue, B5712 Westech Blue, 11SF True Blue, B9118
    Baker Blue, A13096 Baker Dark Gray, B2592 RAL 5009 Azurblau, B7011 Crispin Blue, B2506
    Dezurik Blue,  A14130 Mueller Gray, B9695 Houston Blue, R5477 Mueller Sienna Red.
    Number of Coats: 2-3
    Sequence of Coats: Any combination of Listed colors
    Maximum Field Use Dry Film Thickness (in mils): 18
    Maximum Thinner: 5% Tnemec No. 60 Thinner by volume
    Recoat Cure Time and Temperature: 5 hours at 75°F with accelerator, 9 hours at 75°F
    without accelerator
    Final Cure Time and Temperature: 30 days at 75°F
    Special Comments: Any listed color of Series 22, FC22, N140, or 141 may be substituted
    as a primer of topcoat for Series N140 Pota-Pox Plus provided that both primer and
    topcoat meet their individual Certified end uses. The mix ratio of Part A: Part B is 1:1
    by volume. Part C (Series 44-700 Accelerator) is an optional additive to Part A in the
    field and may be added at up to 4 fluid ounces per two mixed gallons of parts A and B.
[3] Colors: 1211 Red, 1255 Beige, B2506 DeZurik Blue, 15BL Tank White, 39BL Delft Blue, 35GR
    Black, 00WH Tnemec White, B7896 S-B Blue, Y2606 Romac Yellow, B5712 Blue, B2592 RAL 5009
    Azurblau, B7011 Crispin Blue, B9695 Houston Blue, A14130 Mueller Gray, R5477 Mueller
    Sienna Red.
    Number of Coats: 2
    Sequence of Coats: Any combination of Listed colors
    Maximum Field Use Dry film Thickness (in mils): 18
    Maximum Thinner: 5% Tnemec No. 60 Thinner by volume
    Recoat Cure Time and Temperature: 5 hours at 75°F 
    Final Cure Time and Temperature: 30 days at 75°F
    Special Comments: Any listed color of Series 22, FC22, N140, or 141 may be substituted
    as a primer of topcoat for Series N140 Pota-Pox Plus provided that both primer and
    topcoat meet their individual Certified end uses. The mix ratio of Part A: Part B is 1:1
    by volume.

Coatings - Valve[1]
Series N140 Pota-Pox Plus[2] >= 4" CLD 23 EPOXY
Series N140F Pota-Pox Plus Fast Cure[3] >= 4" CLD 23 EPOXY

[1] Meets the health effects requirements of NSF/ANSI/CAN 600 according to requirements of
    NSF/ANSI/CAN 61 for pump, valve, and fitting end use.
[2] Colors: 1211 Red, 1255 Beige,15BL Tank White, 39BL Delft Blue, 35GR Black, 00WH Tnemec
    White, Y2606 Romac Yellow, B8314 Krausz Blue, B5712 Westech Blue, 11SF True Blue, B9118
    Baker Blue, A13096 Baker Dark Gray, B2592 RAL 5009 Azurblau, B7011 Crispin Blue, B2506
    Dezurik Blue,  A14130 Mueller Gray, B9695 Houston Blue, R5477 Mueller Sienna Red.
    Number of Coats: 2-3
    Sequence of Coats: Any combination of Listed colors
    Maximum Field Use Dry Film Thickness (in mils): 18
    Maximum Thinner: 5% Tnemec No. 60 Thinner by volume
    Recoat Cure Time and Temperature: 5 hours at 75°F with accelerator, 9 hours at 75°F
    without accelerator
    Final Cure Time and Temperature: 30 days at 75°F
    Special Comments: Any listed color of Series 22, FC22, N140, or 141 may be substituted
    as a primer of topcoat for Series N140 Pota-Pox Plus provided that both primer and
    topcoat meet their individual Certified end uses. The mix ratio of Part A: Part B is 1:1
    by volume. Part C (Series 44-700 Accelerator) is an optional additive to Part A in the
    field and may be added at up to 4 fluid ounces per two mixed gallons of parts A and B.
[3] Colors: 1211 Red, 1255 Beige, B2506 DeZurik Blue, 15BL Tank White, 39BL Delft Blue, 35GR
    Black, 00WH Tnemec White, B7896 S-B Blue, Y2606 Romac Yellow, B5712 Blue, B2592 RAL 5009
    Azurblau, B7011 Crispin Blue, B9695 Houston Blue, A14130 Mueller Gray, R5477 Mueller
    Sienna Red.
    Number of Coats: 2
    Sequence of Coats: Any combination of Listed colors
    Maximum Field Use Dry film Thickness (in mils): 18
    Maximum Thinner: 5% Tnemec No. 60 Thinner by volume
    Recoat Cure Time and Temperature: 5 hours at 75°F 
    Final Cure Time and Temperature: 30 days at 75°F
    Special Comments: Any listed color of Series 22, FC22, N140, or 141 may be substituted
    as a primer of topcoat for Series N140 Pota-Pox Plus provided that both primer and
    topcoat meet their individual Certified end uses. The mix ratio of Part A: Part B is 1:1
    by volume.



 
Tobar, Inc. 
P.O. Box 1907
Columbus, IN 47202 
United States 
812-375-0400


Facility : Yilan, Taiwan

Joining and Sealing Materials

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Gasket/Sealing Materials
EP1260-04 [1] C. HOT EPDM
EP1270-07 [1] C. HOT EPDM

[1] Certified for a maximum surface area to volume ratio of 2.0 sq. in./L.



 
Tobar, Inc. 
3315 North Scott Drive
Columbus, IN 47201 
United States 
812-375-0400
Visit this company's website


Facility : Chonburi, Thailand

Joining and Sealing Materials

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Gasket/Sealing Materials
E9270-9 [1] [2] C. HOT EPDM

[1] Certified for a maximum surface area to volume ratio of 2.0 sq.in./L.
[2] Evaluated as material for use in mechanical plumbing devices for applications with a
    maximum of 2.0 square inchs per liter.

O-Rings
E9270-9 [1] [2] C. HOT EPDM

[1] Certified for a maximum surface area to volume ratio of 2.0 sq.in./L.
[2] Evaluated as material for use in mechanical plumbing devices for applications with a
    maximum of 2.0 square inchs per liter.



 
TODD Pipe & Supply LLC 
1005 Edward Court
Anaheim, CA 92806 
United States 
714-688-2560
Visit this company's website


Facility : Taichung, Taiwan

Mechanical Devices

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Valves[G]
KS3240-C050 1/2" C. HOT MLTPL
KS3240-C075 3/4" C. HOT MLTPL
KS3240-C100 1" C. HOT MLTPL
KS3240-C125 1 1/4" C. HOT MLTPL
KS3240-C150 1 1/2" C. HOT MLTPL
KS3240-C200 2" C. HOT MLTPL

[G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for
    “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state
    laws and the U.S. Safe Drinking Water Act.

    



 
Tododren S.A de C.V. 
Avenida Frida Kahlo
San Pedro Garza García 
Nuevo León 66269 
Mexico 
52 81 2466 2346


Facility : Apodaca, Nuevo Léon, Mexico

Pipes and Related Products

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Pipe[G]
TDR Forza 4" - 48" CLD 23 PE
TDR PE4710 4" - 48" CLD 23 PE

[G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for
    “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state
    laws and the U.S. Safe Drinking Water Act.

    

NOTE: Only products bearing the NSF Mark on the product, product packaging, and/or
      documentation shipped with the product are Certified.


 
Tomita Pharmaceutical Co., Ltd 
Akinokami Seto-cho
Naruto-City 
Tokushima 771-0360 
Japan 
81 886 88 0511


Facility : Tokushima, Japan

Process Media

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Filtration/Adsorption Media
Granular Calcium Sulfite .15 - 3 mm CLD 23 CASO3

NOTE: Certified for water treatment plant applications.
      This product has not been evaluated for point of use applications.


 
Tomlinson Industries 
4350 Renaissance Parkway
Unit B 
Cleveland, OH 44128 
United States 
216-230-6230
Visit this company's website


Facility : Changhua Hsien, Taiwan

Mechanical Plumbing Devices

Trade Designation      

Faucets
VS143[1] [G]      
VS143AG[1] [G]      
VS603[2] [G]      
VS603AG[2] [G]      
VS713[2] [G]      
VS713AG[2] [G]      
VS802[3] [G]      
VS802AG[3] [G]      
VS888[2] [G]      
VS888AG[2] [G]      
VS905[2] [G]      
VS905AG[2] [G]      

[1] Available in Polished Chrome or Satin Nickel finishes.
[2] Available in Polished Chrome, Antique Bronze, or Satin Nickel finishes.
[3] Available in Polished Chrome only.
[G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for
    “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state
    laws and the U.S. Safe Drinking Water Act.

    



 
Toray Advanced Materials Korea Inc. 
6F, 7, Magokdong-ro 10-gil
Gangseo-gu, Seoul 07790 
Korea, Republic of 
82 23 279 7000
Visit this company's website


Facility : Gyeongsangbuk-do, Republic of Korea

Mechanical Devices

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Reverse Osmosis Element[1]
NE4040-40[2] 4" x 40" CLD 23 MLTPL
NE4040-70[2] 4" x 40" CLD 23 MLTPL
NE4040-90[2] 4" x 40" CLD 23 MLTPL
NE8040-40[2] 8" x 40" CLD 23 MLTPL
NE8040-70[2] 8" x 40" CLD 23 MLTPL
NE8040-90[2] 8" x 40" CLD 23 MLTPL
RE16040-BE[3] 16" x 40" CLD 23 MLTPL
RE16040-BLN[3] 16" x 40" CLD 23 MLTPL
RE16040-BLR[3] 16" x 40" CLD 23 MLTPL
RE16040-FE[3] 16" x 40" CLD 23 MLTPL
RE16040-FEn[3] 16" x 40" CLD 23 MLTPL
RE16040-SHF[3] 16" x 40" CLD 23 MLTPL
RE16040-SHN[3] 16" x 40" CLD 23 MLTPL
RE4021-BLF[5] [6] 4" x 21" CLD 23 MLTPL
RE4040-BE[5] [6] 4" x 40" CLD 23 MLTPL
RE4040-BLF[2] 4" x 40" CLD 23 MLTPL
RE4040-BLN[2] 4" x 40" CLD 23 MLTPL
RE4040-BLR[2] 4" x 40" CLD 23 MLTPL
RE4040-CE[2] [4] 4" x 40" CLD 23 MLTPL
RE8040-BE[2] 8" x 40" CLD 23 MLTPL
RE8040-BE34[2] 8" x 40" CLD 23 MLTPL
RE8040-BE440[3] 8" x 40" CLD 23 MLTPL
RE8040-BLF[2] 8" x 40" CLD 23 MLTPL
RE8040-BLF440[3] 8" x 40" CLD 23 MLTPL
RE8040-BLN[2] 8" x 40" CLD 23 MLTPL
RE8040-BLN440[3] 8" x 40" CLD 23 MLTPL
RE8040-BLR[2] 8" x 40" CLD 23 MLTPL
RE8040-BLR440[3] 8" x 40" CLD 23 MLTPL
RE8040-BN[3] 8" x 40" CLD 23 MLTPL
RE8040-CE[3] 8" x 40" CLD 23 MLTPL
RE8040-FDn[3] 8" x 40" CLD 23 MLTPL
RE8040-FE[3] 8" x 40" CLD 23 MLTPL
RE8040-FEN34 8" x 40" CLD 23 MLTPL
RE8040-FEn[3] 8" x 40" CLD 23 MLTPL
RE8040-FEn440[3] 8" x 40" CLD 23 MLTPL
RE8040-FLF[2] 8" x 40" CLD 23 MLTPL
RE8040-FLF34[2] 8" x 40" CLD 23 MLTPL
RE8040-FLF440[3] 8" x 40" CLD 23 MLTPL
RE8040-FLR[5] [6] 8" x 40" CLD 23 MLTPL
RE8040-FLR34[2] 8" x 40" CLD 23 MLTPL
RE8040-FLR440[5] [6] 8" x 40" CLD 23 MLTPL
RE8040-FN[3] 8" x 40" CLD 23 MLTPL
RE8040-SFR[5] [6] 8" x 40" CLD 23 MLTPL
RE8040-SHF[3] 8" x 40" CLD 23 MLTPL
RE8040-SHF400[3] 8" x 40" CLD 23 MLTPL
RE8040-SHN[3] 8" x 40" CLD 23 MLTPL
RE8040-SHN400[3] 8" x 40" CLD 23 MLTPL

[1] Sizes refer to the diameter x length.
[2] Certified for a minimum flow of 8,330 liters per day.
[3] Certified for a minimum permeate flow of 20,000 liters per day.
[4] Elements require a 30 minute pre-service flush.
[5] Elements require a 1 hr pre-service flush.
[6] Certified for the following minimum permeate flow rates (gallons per day)
    RE 4021-BLF : 2,220
    RE 4040-BE : 2,220
    RE 8040-FLR : 9,000
    RE 8040-FLR440 : 9,900
    RE 8040-SFR : 7,500
    
    

NOTE: Only products bearing the NSF Mark on the product, product packaging, and/or
      documentation shipped with the product are Certified.


 
Toray Industries, Inc. 
9-1 Oe-cho, Minato-ku
Nagoya 455-8502 
Japan 
81 52 613 5197


Facility : # 1

Potable Water Materials

    Water Water
    Contact Contact
Trade Designation End Use Temp Material

Potable Water Materials[1]
Torelina A673MB2 A,F,P C. HOT PPS
Torelina A673MTB A,F,P C. HOT PPS

[1] Only products bearing the NSF Mark on the product, product packaging, and/or
    documentation shipped with the product are Certified.

NOTE: If material / packaging marking identifies: "1" the location of the facility is
      Aichi-ken, Japan


Facility : # 3

Potable Water Materials

    Water Water
    Contact Contact
Trade Designation End Use Temp Material

Potable Water Materials[1]
Torelina A604B A,F,P C. HOT PPS
Torelina A604G A,F,P C. HOT PPS
Torelina A604WR A,F,P C. HOT PPS
Torelina A604WRB A,F,P C. HOT PPS
Torelina A604WRG A,F,P C. HOT PPS

[1] Only products bearing the NSF Mark on the product, product packaging, and/or
    documentation shipped with the product are Certified.

NOTE: If material / packaging marking identifies: "3" the location of the facility is
      Shizuoka-ken, Japan


Facility : # 6

Potable Water Materials

    Water Water
    Contact Contact
Trade Designation End Use Temp Material

Potable Water Materials[1]
Torelina A310MX04B A,F,P C. HOT PPS
Torelina A504X90B A,F,P C. HOT PPS
Torelina A604WR A,F,P C. HOT PPS
Torelina A604WRB A,F,P C. HOT PPS
Torelina A604WRG A,F,P C. HOT PPS

[1] Only products bearing the NSF Mark on the product, product packaging, and/or
    documentation shipped with the product are Certified.

NOTE: If material / packaging marking identifies: "6"   the location of the facility is
      Shenzhen, China.


Facility : TN

Potable Water Materials

    Water Water
    Contact Contact
Trade Designation End Use Temp Material

Potable Water Materials[1]
Torelina A673MTB A,F,P C. HOT PPS
Torelina A673MWR A,F,P C. HOT PPS
Torelina A673MWRB A,F,P C. HOT PPS

[1] Only products bearing the NSF Mark on the product, product packaging, and/or
    documentation shipped with the product are Certified.

NOTE: If material / packaging marking identifies: "TN" the location of the facility is
      Bangkok, Thailand


Facility : TR

Potable Water Materials

    Water Water
    Contact Contact
Trade Designation End Use Temp Material

Potable Water Materials[1]
Torelina A604WR A,F,P C. HOT PPS
Torelina A604WRB A,F,P C. HOT PPS
Torelina A604WRG A,F,P C. HOT PPS
Torelina A670MWR1B A,F,P C. HOT PPS

[1] Only products bearing the NSF Mark on the product, product packaging, and/or
    documentation shipped with the product are Certified.

NOTE: If material / packaging marking identifies: "TR" the location of the facility is
      Indiana, U.S.A.


Facility : K

Potable Water Materials

    Water Water
    Contact Contact
Trade Designation End Use Temp Material

Potable Water Materials[1]
Torelina A670MWR1B F,P C. HOT PPS
Torelina A670R63B2 A,F,P C. HOT PPS
Torelina A670R63G2 A,F,P C. HOT PPS
Torelina A670R63N2 A,F,P C. HOT PPS
Torelina A673MB A,F,P C. HOT PPS
Torelina A675MB A,F,P C. HOT PPS

[1] Only products bearing the NSF Mark on the product, product packaging, and/or
    documentation shipped with the product are Certified.

NOTE: If material / packaging marking identifies: "K" the location of the facility is
      Nara-ken, Japan


Facility : KR

Potable Water Materials

    Water Water
    Contact Contact
Trade Designation End Use Temp Material

Potable Water Materials[1]
Torelina A673MB2 A,F,P C. HOT PPS
Torelina A673MTB A,F,P C. HOT PPS
Torelina A673MTD A,F,P C. HOT PPS

[1] Only products bearing the NSF Mark on the product, product packaging, and/or
    documentation shipped with the product are Certified.

NOTE: If material / packaging marking identifies: "KR" the location of the facility is 
      Gunsan, Repuplic of Korea   


 
Toray Industries, Inc. 
1-1-2, Nihonbashi-Muromachi
Chuo-ku, Tokyo 
103-8666 
Japan 
81 3 3245 4542
Visit this company's website


Facility : F3

Mechanical Devices

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Ultrafiltration Devices [G]
HFU-2020AN[1] [3] 8.5" x 85" CLD 23 MLTPL
HFUG-2020AN[2] [3] 8.5" x 85" CLD 23 MLTPL

[1] Certified for a minimum daily flow of 36,000 liters.
[2] Certified for a minimum daily flow of 45,000 liters.
[3] Membranes should be flushed with tap water for 30 minutes before being placed into
    service at the following flow rates:																		
    HFU-2020AN at 25 liters per minute																		
    HFUG-2020AN at 31 liters per minute
[G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for
    “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state
    laws and the U.S. Safe Drinking Water Act.

    

NOTE: If “F3” is indicated in the first two digits of the lot number, the facility location is
      Suzhou, China.


Facility : F4

Mechanical Devices

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Ultrafiltration Devices [G]
HFU-2020AN[1] [2] 8.5" x 85" CLD 23 MLTPL
HFU-B2315AN[2] [3] 7" x 91.8" CLD 23 MLTPL
HFUG-2020AN[2] [4] 8.5" x 85" CLD 23 MLTPL
HFUG-2020HN[2] [4] 8.5" x 85" CLD 23 MLTPL
HFUG-B2315AN[2] [5] 7" x 91.8" CLD 23 MLTPL

[1] Certified for a minimum daily flow of 36,000 liters.
[2] Membranes should be flushed with tap water for 30 minutes before being placed into
    service at the following flow rates:																		
    HFU-2020AN at 25 liters per minute																		
    HFUG-2020AN and HFUG-2020HN at 31 liters per minute																	
    HFU-B2315AN at 20.8 liters per minute																		
    HFUG-2315AN at 26 liters per minute
[3] Certified for a minimum daily flow of 30,000 liters.
[4] Certified for a minimum daily flow of 45,000 liters.
[5] Certified for a minimum daily flow of 37,500 liters.
[G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for
    “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state
    laws and the U.S. Safe Drinking Water Act.

    

NOTE: If “F4” is indicated in the first two digits of the lot number, the facility location is
      Gyeongsangbuk-do, Korea.


 
Toro Equipment S.L. 
Ctra. Nacional VP-3302, Km 11
Villavaquerín, 47329 Valladolid 
CIF: B47664966 
Spain 
34 98 340 30 47
Visit this company's website


Facility : Valladolid, Spain

Protective (Barrier) Materials

    Water Water
  Water Contact Contact Contact
Trade Designation Size Restriction Temp Material

Storage Tanks/Reservoirs[1] [G]
SETTLING W-TANK 10,804 - 2,641,720 gal. CLD 23 MLTPL
W-TANK 10,804 - 2,641,720 gal. CLD 23 MLTPL

[1] Certification requested for water storage only.  Certification does not include the
    reservoir's concrete floor or joint grout.
[G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for
    “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state
    laws and the U.S. Safe Drinking Water Act.

    

NOTE: Only products bearing the NSF Mark on the product, product packaging, and/or
      documentation shipped with the product are Certified.


 
Toshiba Infrastructure Systems & Solutions Corporation 
1 Toshiba-cho, Fuchu-shi
Tokyo 183-8511 
Japan 
81 42 333 2226


Facility : Chongqing, China

Mechanical Devices

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Water Meters
Electromagnetic Flowmeter GF63(1)(2)(3)E(4)(5)(6)[1] [G] 1/2" - 10" CLD 23 MLTPL
Electromagnetic Flowmeter GF63(1)(2)(3)N(4)(5)(6)[2] [G] 4" - 18" CLD 23 MLTPL
Electromagnetic Flowmeter GF63(1)(2)(3)T(4)(5)(6)[3] [G] 12" - 24" CLD 23 MLTPL
Electromagnetic Flowmeter LF65(1)(2)(3)(4)(5)N(6)(7)(8)(9)[5] [G] 4" - 18" CLD 23 MLTPL
Electromagnetic Flowmeter LF65(1)(2)(3)(4)(5)P(6)(7)(8)(9)[6] [G] 1/2" - 18" CLD 23 MLTPL
Electromagnetic Flowmeter LF66(0)(1)(2)(3)(4)E(5)(6)(7)[7] [G] 20" - 120" D. HOT MLTPL
Electromagnetic flowmeter LF65(0)(1)(2)(3)(4)E(5)AA(6)[4] [G] 4" - 18" D. HOT MLTPL

[1] GF63(1)(2)(3)E(4)(5)(6):
    (1) Mounting Style
        0 - Detector / Converter integral type
        2 - Detector / Converter separate type
    (2) Meter Size
        01 - 1/2", 15mm
        02 - 1", 25mm
        03 - 1 1/4", 32mm
        04 - 1 1/2", 40mm
        05 - 2", 50mm
        06 - 2 1/2 ", 65mm
        08 - 3", 80mm
        10 - 4", 100mm
        12 - 5", 125mm
        15 - 6", 150mm
        20 - 8", 200mm
        25 - 10", 250mm
    (3) Connection flange standard
    (4) Electrode material
        B - 316L stainless steel
        C - Ti (titanium) F: Hastelloy C
    (5) Flow and calibration velocity range
    (6) Grounding ring
        1 - Without Grounding rings
        2 - With Grounding rings * Grounding rings are optional in this model. 
            When present, they will be the same material as the electrode.
[2] (1) Mounting Style 
        0: Detector / Converter integral type 
        2: Detector / Converter separate type 
    (2) Meter Size
          10: 4", 100mm
          12: 5", 125mm
          15: 6", 150mm
          20: 8", 200mm
          25: 10", 250mm
          30: 12", 300mm
          35: 14", 350mm
          40: 16", 400mm
          45: 18", 450mm
    (3) Connection flange standard 
    (4) Electrode material 
        B: 316L stainless steel 
        C: Ti (titanium)
        F: Hastelloy C
    (5) Flow and calibration velocity range 
    (6) Grounding ring 
        1: Without Grounding rings 
        2: With Grounding rings 
    * Grounding rings are optional in this model. When present, they will be the same       
       material as the electrode.
[3] GF63(1)(2)(3)T(4)(5)(6):
    (1) Mounting Style
        0 - Detector / Converter integral type
        2 - Detector / Converter separate type
    (2) Meter Size
        30 - 12", 300mm
        35 - 14", 350mm
        40 - 16", 400mm
        45 - 18", 450mm
        50 - 20", 500mm
        60 - 24", 600mm
    (3) Connection flange standard
    (4) Electrode material
        B - 316L stainless steel
        C - Ti (titanium) F: Hastelloy C
    (5) Flow and calibration velocity range
    (6) Grounding ring
        1 - Without Grounding rings
        2 - With Grounding rings * Grounding rings are optional in this model. 
            When present, they will be the same material as the electrode.
[4] LF65 models
    (0) Type
        0 - Normal type
        4 - Hazard location Certification type
    (1) Size inches(mm)
        J - 4 (100mm)
        U - 5 (125mm)
        K - 6 (150mm)
        L - 8 (200mm)
        M - 10 (250mm)
        N - 12 (300mm)
        P - 14 (350mm)
        Q - 16 400mm)
        R - 18 (450mm)
    (2) Mounting style
        L - Detector/Converter combined type
        M - Detector/Converter separate type
    [3] Connection flange standard, overall length
        C - ANSI 150, ISO length
        D - ANSI 300, ISO length
        G - DIN PN 10, ISO length
        H - DIN PN 16, ISO length
        1 - ANSI 150, Toshiba length
        2 - ANSI 300, Toshiba length
        5 - DIN PN 10, Toshiba length
        6 - DIN PN 16, Toshiba length
        Z - Other
    (4) Electrode material
        B - 316L stainless steel
        C - Ti (titanium)
        F - Hastelloy C
    (5) Grounding Ring Material
        C - 316 stainless steel
        D - 316L stainless steel
        E - Ti (titanium)
        H - Hastelloy C
    [6] Coating (External)
[5] (1) Type 
        0: Normal type 
        4: Hazard location certification type 
    (2) Meter Size 
          J: 4", 100mm
          U: 5", 125mm
          K: 6", 150mm
          L: 8", 200mm
          M: 10", 250mm
          N: 12", 300mm
          P: 14", 350mm
          Q: 16", 400mm
          R: 18", 450mm
    (3) Mounting Style 
        L: Detector/Converter integral type 
        M: Detector/Converter separate type 
    (4) Connection flange standard 
    (5) Electrode material 
        B: 316L stainless steel 
        C: Ti (titanium)
        F: Hastelloy C
    (6) Grounding ring material 
        C: 316 stainless steel 
        D: 316L stainless steel 
        E: Ti (titanium)
        H: Hastelloy C
    (7) Flow and calibration velocity range 
    (8) Excitation and signal cables 
    (9) Coating (External)
[6] LF65(1)(2)(3)(4)(5)P(6)(7)(8)(9):
    (1) Type
        0 - Normal type
        4 - Hazard location certification type
    (2) Meter Size
        D - 1/2", 15mm
        E - 1", 25mm S: 1 1/4", 32mm
        F - 1 1/2", 40mm
        G - 2", 50mm
        W - 2 1/2", 65mm
        H - 3", 80mm
        J - 4", 100mm
        U - 5", 125mm
        K - 6", 150mm
        L - 8", 200mm
        M - 10", 250mm
        N - 12", 300mm
        P - 14", 350mm
        Q - 16", 400mm
        R - 18", 450mm
    (3) Mounting Style
        L - Detector / Converter integral type
        M - Detector / Converter separate type
    (4) Connection flange standard
    (5) Electrode material
        B - 316L stainless steel
        C - Ti (titanium)
        F - Hastelloy C
    (6) Grounding ring material
        C - 316 stainless steel
        D - 316L stainless steel
        E - Ti (titanium)
        H - Hastelloy C
    (7) Flow and calibration velocity range
    (8) Excitation and signal cables
    (9) Coating (External)
[7] LF66 Models
    (0) Type
        0 - Normal type
        4 - Hazard location Certification type
    (1) Size inches (mm)
        50 - 20 (500mm)
        60 - 24 (600mm)
        70 - 28 (700mm)
        75 - 30 (750mm)
        80 - 32 (800mm)
        90 - 36 (900mm)
        A0 - 40 (1000mm)
        A1 - 42 (1050mm)
        A2 - 48 (1200mm)
        A3 - 54 (1350mm)
        A4 - 56 (1400mm)
        A5 - 60 (1500mm)
        A6 - 64 (1600mm)
        A7 - 66 (1650mm)
        A8 - 72 (1800mm)
        A9 - 78 (1950mm)
        B0 - 80 (2000mm)
        B2 - 88 (2200mm)
        B4 - 96 (2400mm)
        B6 - 104 (2600mm)
        B8 - 112 (2800mm)
        C0 - 120 (3000mm)
    (2) Mounting style
        A - Detector/Converter combined type
        B - Detector/Converter separate type
    (3) Connection flange standard, overall length
        A - AWWA class D (over 28)
        C - ANSI Class 150 ( up to 24)
        B - EN 1092-1 PN6 (DIN)
        E - EN 1092-1 PN10 (DIN)
        J - JIS 10K
    (4) Electrode Material
        K - AISI 316L
        C - Titanium
        F - Hastelloy C
    (5) Grounding Ring Material
        A - Not provided
        C - AISI 316 (Option)
        E - Titanium (Option)
        H - Hastelloy C (equivalent) (Option)
    (6) Dedicated preformed cable
         A - Not provided
    (7) Structure and Coating (External)
[G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for
    “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state
    laws and the U.S. Safe Drinking Water Act.

    



 
Tosin Industrial Corporation 
No. 117, Lane 460, Nanshi Sec. 2
Zhongfeng Road, Pingzhen District 
Taoyuan City 324 
Taiwan 
886 3 4398801


Facility : Taoyuan, Taiwan

Mechanical Plumbing Devices

Trade Designation      

Gasket/Sealing Materials[1]
EPDM 60 (3E60B11P)[2]      
EPDM 60 (3E60B18P)[2]      
EPDM 70 (3E70B03P)[2]      
EPDM 70 (3E70B16P)[2]      

[2] Certified for a maximum surface area to volume ratio of 2.0 sq. in./L.

[1] This product does not require a Q statistic. It is made from material or materials that
    do not require lead analysis when reviewed per NSF/ANSI/CAN Standard 61, Section 3.3.

O-Rings[1]
EPDM 60 (3E60B11P)[2]      
EPDM 60 (3E60B18P)[2]      
EPDM 70 (3E70B03P)[2]      
EPDM 70 (3E70B16P)[2]      

[2] Certified for a maximum surface area to volume ratio of 2.0 sq. in./L.

[1] This product does not require a Q statistic. It is made from material or materials that
    do not require lead analysis when reviewed per NSF/ANSI/CAN Standard 61, Section 3.3.



 
ToxSorb Ltd. 
P.O. Box 293
Kibutz, Kfar Giladi 12210 
Israel 
972 4 690 1014
Visit this company's website


Facility : Kiryat Shmona, Israel

Process Media

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Granular Activated Carbon[1]
MAC - NP2 12 - 40 mesh CLD 23 GAC

[1] The Carbon Source is bituminous coal.

NOTE: Certified for water treatment plant applications.
      This product has not been evaluated for point of use applications.


 
TOYO VALVE Co., Ltd. 
Tokyo Shiodome Building 1-9-1
Higashi-Shimbashi Minato-ku 
Tokyo 105-7305 
Japan 
81 33 249 5311
Visit this company's website


Facility : # 1 Japan

Mechanical Devices

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Valves[1] [G]
(TY)AKSZAN (5044ALF) 1 1/4" - 2" C. HOT MLTPL
(TY)AKSZANW (5044WLF) 1 1/4" - 2" C. HOT MLTPL
(TY)CSZAN (5049ALF) 1 1/4" - 2" C. HOT MLTPL
(TY)CSZANW (5049WLF) 1 1/4" - 2" C. HOT MLTPL

[1] Only products bearing the NSF Mark are Certified.
[G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for
    “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state
    laws and the U.S. Safe Drinking Water Act.

    



Facility : Samutprakarn, Thailand

Mechanical Devices

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Valves[1] [G]
(RW02)AK125CN (211ALF) 1/2" - 2" CLD 23 MLTPL
(RW02)AKHN (206ALF) 1/2" - 2" CLD 23 MLTPL
(RW02)AKTAFCN (5046LF) 1/2" - 3/4" C. HOT MLTPL
(RW02)AKYRN (236ALF) 1/2" - 2" CLD 23 MLTPL
(RW02)AKYRNT (236TLF) 1/2" - 2" CLD 23 MLTPL
(RW02)C125CN (212ALF) 1/2" - 2" CLD 23 MLTPL
(RW02)CHN (207ALF) 1/2" - 2" CLD 23 MLTPL
(RW02)CYRN (237ALF) 1/2" - 2" CLD 23 MLTPL
(TY)AKSZAN (5044ALF) 1/4" - 1", 2 1/2"-3" C. HOT MLTPL
(TY)AKSZANW (5044WLF) 1/4" - 1" C. HOT MLTPL
(TY)CSZAN (5049ALF) 1/2" - 1", 2 1/2"-3" C. HOT MLTPL
(TY)CSZANW (5049WLF) 1/2" - 1" C. HOT MLTPL

[1] Only products bearing the NSF Mark are Certified.
[G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for
    “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state
    laws and the U.S. Safe Drinking Water Act.

    



 
TOYOBO MC Corporation 
Osaka Umeda Twin Towers South
1-13-1 Umeda, Kita-ku 
Osaka 530-0001 
Japan 
81 6 6348 3360
Visit this company's website


Facility : # 1 China

Mechanical Devices

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Reverse Osmosis Element[1] [2] [3]
SB410HF 4" x 40" CLD 23 MLTPL
SB415-1 4" x 40" CLD 23 MLTPL
SB415HF 4" x 40" CLD 23 MLTPL
SB810HF 8" x 40" CLD 23 MLTPL
SB815-1 8" x 40" CLD 23 MLTPL
SB815HF 8" x 40" CLD 23 MLTPL
SL415 4" x 40" CLD 23 MLTPL
SL415HF-2 4" x 40" CLD 23 MLTPL
SL815 8" x 40" CLD 23 MLTPL
SL815HF-2 8" x 40" CLD 23 MLTPL

[1] Size is expressed as Diameter x length.
[2] SB815-1 model is Certified for a minimum daily flow of 10000 gallons.
    SB415-1 model is Certified for a minimum daily flow of 2400 gallons.
    SB815HF model is Certified for a minimum daily flow of 13,000 gallons.
    SB415HF models are Certified for a minimum daily flow of 2,900 gallons.
    SB810HF model is Certified for a minimum daily flow of 12,500 gallons.
    SB410HF model is Certified for a minimum daily flow of 2,700 gallons.
    SL815HF-2 model is Certified for a minimum daily flow of 11,500 gallons.
    SL415HF-2 model is Certified for a minimum daily flow of 2,300 gallons.
    SL815 model is Certified for a minimum daily flow of 9,500 gallons.
    SL415 model is Certified for a minimum daily flow of 2,000 gallons.
[3] All models 4” in diameter require a 4 gpm flush for 24 hours using tap water.
    All models 8” in diameter require a 15 gpm flush for 24 hours using tap water.



 
TPR Fiberdur GmbH & Co. KG 
Industriepark Emil Mayrisch
Aldenhoven 52457 
Germany 
49 2464 972450


Facility : Aldenhoven, Germany

Pipes and Related Products

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Fittings [2]
Fiberdur Epoxy® Fittings EP10 100 mm - 330 mm CLD 23 TSRE
Fiberdur Epoxy® Fittings EP16 100 mm - 330 mm CLD 23 TSRE
Fiberdur Epoxy® Fittings EP6 100 mm - 330 mm CLD 23 TSRE
VE Bogen 45° 40 mm - 1200 mm[1] D. HOT VE
VE Bogen 90° 40 mm - 1200 mm[1] D. HOT VE
VE Bund 40 mm - 1200 mm[1] D. HOT VE
VE Muffe 40 mm - 1200 mm[1] D. HOT VE
VE Reduzierung 40 mm - 1200 mm[1] D. HOT VE
VE T-Stueck 40 mm - 1200 mm[1] D. HOT VE

[1] Certified for equivalent size of 1.57" to 47"
[2] Only products bearing the NSF Mark on the product, product packaging, and/or
    documentation shipped with the product are Certified.

Pipe[2]
Fiberdur® Wickelrohre EP10 100 mm - 330 mm CLD 23 TSRE
Fiberdur® Wickelrohre EP16 100 mm - 330 mm CLD 23 TSRE
Fiberdur® Wickelrohre EP6 100 mm - 330 mm CLD 23 TSRE
VE Pipe, DN40-DN1200 40 mm - 1200 mm D. HOT VE

[2] Only products bearing the NSF Mark on the product, product packaging, and/or
    documentation shipped with the product are Certified.



 
Treibacher Industrie AG 
Auer-von-Welsbach-Straße 1
9330 Althofen 
Austria 
0043 (0) 4262/505-0
Visit this company's website


Facility : #35425

Process Media

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Adsorption Media
NXT-2 8 mesh - 325 mesh CLD 23 -
NXT-2F 8 mesh - 325 mesh CLD 23 -
NXT-2H 8 mesh - 325 mesh CLD 23 -
NXT-4 8 mesh - 325 mesh CLD 23 -

NOTE: Certified for water treatment plant applications.
      This product has not been evaluated for point of use applications.


 
Trelleborg Pipe Seals Tijuana S.A de C.V 
Colina No. 11850, Parque
Industrial el Florido, Sección Colinas 
Tijuana, BC 22237 
Mexico 
52 664 625 4885


Facility : Tijuana, Baja California, Mexico

Joining and Sealing Materials

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Gasket/Sealing Materials [G]
E 148 T-552 ANGER LOCK IPS EPDM 2" - 14" CLD 23 EPDM
E 148 T-560 RIEBER IPS EPDM 1 1/2" - 24" CLD 23 EPDM
E 148 T-565 RIEBER C-900 EPDM 4" - 48" CLD 23 EPDM
E 148 T-584 ANGER LOCK EPDM 4" - 48" CLD 23 EPDM
E 148 T-603 POWER LOCK IPS EPDM 1 1/2" - 12" CLD 23 EPDM
FLUID-TITE EPDM CIOD 6"- 24" CLD 23 EPDM
FLUID-TITE NITRILE CIOD 6"- 24" CLD 23 NBR
MP 148 T-560 RIEBER IPS SBR[1] 1 1/2" - 24" CLD 23 SBR
MP 148 T-565 RIEBER C-900 SBR[1] 4" - 48" CLD 23 SBR
MP 48 T-559 RIEBER PRESSURE METRIC SBR[1] 450 mm - 1200 mm CLD 23 SBR
NR 648 T-560 RIEBER IPS NITRILE 1 1/2" - 24" CLD 23 NBR
NR 648 T-565 RIEBER C-900 NITRILE 4" - 48" CLD 23 NBR
T-552 ANGER LOCK IPS EPDM 2" - 14" CLD 23 EPDM
T-559 RIEBER PRESSURE METRIC SBR[1] 450 mm - 1200 mm CLD 23 SBR
T-560 RIEBER IPS EPDM 1 1/2" - 24" CLD 23 EPDM
T-560 RIEBER IPS NITRILE 1 1/2" - 24" CLD 23 NBR
T-560 RIEBER IPS SBR[1] 1 1/2" - 24" CLD 23 SBR
T-565 RIEBER C-900 EPDM 4" - 48" CLD 23 EPDM
T-565 RIEBER C-900 NITRILE 4" - 48" CLD 23 NBR
T-565 RIEBER C-900 SBR[1] 4" - 48" CLD 23 SBR
T-584 ANGER LOCK EPDM 4" - 48" CLD 23 EPDM
T-603 POWER LOCK IPS EPDM 1 1/2" - 12" CLD 23 EPDM

[1] Certified for a maximum surface area to volume ratio of 2.0 sq. in./L.
[G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for
    “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state
    laws and the U.S. Safe Drinking Water Act.

    

O-Rings [G]
CERTA-LOK O-RING EPDM 2" - 10" CLD 23 EPDM
CERTA-LOK O-RING NITRILE 2" - 10" CLD 23 NBR
CERTA-LOK O-RING SBR[1] 5" - 48" CLD 23 SBR

[1] Certified for a maximum surface area to volume ratio of 2.0 sq. in./L.
[G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for
    “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state
    laws and the U.S. Safe Drinking Water Act.

    



 
Trelleborg Sealing Solutions Americas, Inc. 
2509 Bremer Road
Fort Wayne, IN 46803 
United States 
260-749-9631
Visit this company's website


Facility : Fort Wayne, IN

Joining and Sealing Materials

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Gasket/Sealing Materials
E75F2[1] [2] C. HOT EPDM

[1] This product has also been evaluated for use in Mechanical Plumbing Device applications
    with a maximum use restriction of 3.0 sq. in. /L.
[2] Certified for a maximum surface area to volume ratio of 3.0 sq. in. /L.

O-Rings
E75F2[1] [2] C. HOT EPDM

[1] This product has also been evaluated for use in Mechanical Plumbing Device applications
    with a maximum use restriction of 3.0 sq. in. /L.
[2] Certified for a maximum surface area to volume ratio of 3.0 sq. in. /L.



Facility : Guangdong, China

Joining and Sealing Materials

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Gasket/Sealing Materials
E7W14 [1] C. HOT EPDM

[1] Certified for a maximum surface area to volume ratio of 10 square inches per liter.

O-Rings
E7W14 [1] C. HOT EPDM

[1] Certified for a maximum surface area to volume ratio of 10 square inches per liter.


Mechanical Plumbing Devices

Trade Designation      

Gasket/Sealing Materials[1]
E7W14[2]      

[2] Certified for a maximum surface area to volume ratio of 10 square inches per liter.

[1] This product does not require a Q statistic. It is made from material or materials that
    do not require lead analysis when reviewed per NSF/ANSI/CAN Standard 61, Section 3.3

O-Rings[1]
E7W14 [2]      

[2] Certified for a maximum surface area to volume ratio of 10 square inches per liter.

[1] This product does not require a Q statistic. It is made from material or materials that
    do not require lead analysis when reviewed per NSF/ANSI/CAN Standard 61, Section 3.3



Facility : Tatu, Taichung, Taiwan

Joining and Sealing Materials

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Gasket/Sealing Materials
E7W14 [1] C. HOT EPDM

[1] Certified for a maximum surface area to volume ratio of 10 square inches per liter.

O-Rings
E7W14 [1] C. HOT EPDM

[1] Certified for a maximum surface area to volume ratio of 10 square inches per liter.


Mechanical Plumbing Devices

Trade Designation      

Gasket/Sealing Materials[1] [2]
E7W14      

[1] Certified for a maximum surface area to volume ratio of 10 square inches per liter.
[2] This product does not require a Q statistic. it is made from material or materials that
    do not require lead analysis when reviewed per NSF/ANSI/CAN Standard 61, Section 3.3

O-Rings[1] [2]
E7W14      

[1] Certified for a maximum surface area to volume ratio of 10 square inches per liter.
[2] This product does not require a Q statistic. it is made from material or materials that
    do not require lead analysis when reviewed per NSF/ANSI/CAN Standard 61, Section 3.3



Facility : Bien Hoa City, Dong Nai, Vietnam

Joining and Sealing Materials

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Gasket/Sealing Materials
E7W14[1] [2] C. HOT EPDM
ECW01 [3] [4] C. HOT EPDM

[1] This product has also been evaluated for use in Mechanical Plumbing Device applications
    with a maximum use restriction of 10.0 square inches/L.
[2] Certified for a maximum surface area to volume ratio of 10 square inches per liter.
[3] This product is to also be evaluated for use in Mechanical Plumbing Device applications
    with a maximum use restriction of 3 square inches/L.
[4] Certified for a maximum surface area to volume ratio of 3 square inches per liter.

O-Rings
E7W14[1] [2] C. HOT EPDM
ECW01 [3] [4] C. HOT EPDM

[1] This product has also been evaluated for use in Mechanical Plumbing Device applications
    with a maximum use restriction of 10.0 square inches/L.
[2] Certified for a maximum surface area to volume ratio of 10 square inches per liter.
[3] This product is to also be evaluated for use in Mechanical Plumbing Device applications
    with a maximum use restriction of 3 square inches/L.
[4] Certified for a maximum surface area to volume ratio of 3 square inches per liter.



 
Trelleborg Sealing Solutions Germany GmbH 
Schockenriedstr. 1
Stuttgart 70565 
Germany 
49 711 7864 717


Facility : Castelli Calepio, Italy

Mechanical Plumbing Devices

Trade Designation      

Gasket/Sealing Materials[1]
E7518      

[1] Certified for a maximum surface area to volume ratio of 2.95 sq. in./L.

O-Rings[1]
E7518      

[1] Certified for a maximum surface area to volume ratio of 2.95 sq. in./L.



 
Trelleborg Sealing Solutions Germany GmbH 
Schockenriedstr. 1
70565 Stuttgart 
Germany 
49 711 7864 717


Facility : # 1 Italy

Mechanical Plumbing Devices

Trade Designation      

Gasket/Sealing Materials
E7518[1]      

[1] Certified for a maximum surface area to volume ratio of 2.95 sq. in./L.

O-Rings
E7518[1]      

[1] Certified for a maximum surface area to volume ratio of 2.95 sq. in./L.



 
Trelleborg Sealing Solutions Germany GmbH 
Schockenriedstrabe 1
70565 Stuttgart 
Germany 
49 7 117 8640
Visit this company's website


Facility : Bergamo, Italy

Joining and Sealing Materials

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Gasket/Sealing Materials[1]
(x)E7581 [2] [3] C. HOT EPDM

[1] This product has also been evaluated for use in Mechanical Plumbing Device applications
    with a maximum use restriction of 7.75 sq. in./L.
[2] Material type EPDM 70 black
        (x) - any alphanumeric digit
[3] Certified for a maximum surface area to volume ratio of 7.75 sq. in./L.

O-Rings[1]
(x)E7581[2] [3] C. HOT EPDM

[1] This product has also been evaluated for use in Mechanical Plumbing Device applications
    with a maximum use restriction of 7.75 sq. in./L.
[2] Material type EPDM 70 black
        (x) - any alphanumeric digit
[3] Certified for a maximum surface area to volume ratio of 7.75 sq. in./L.



 
Trelleborg Sealing Solutions Plymouth LLC 
1100 Xenium Lane North
Plymouth, MN 55441 
United States 
800-927-1422 
952-927-1400
Visit this company's website


Facility : # 1 China

Joining and Sealing Materials

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Gasket/Sealing Materials[1]
558CK [2] C. HOT EPDM
559GT [2] C. HOT EPDM

[1] This product has also been evaluated for use in Mechanical Plumbing Device applications
    with a maximum use restriction of 2.0 sq. in./L.
[2] Certified for maximum surface area to volume ratio of 2.0 sq. in./L.

NOTE: Only products bearing the NSF Mark on the product, product packaging, and/or
      documentation shipped with the product are Certified.


Facility : Mason City, IA

Joining and Sealing Materials

    Water Water
    Contact Contact
Trade Designation Size Temp Material

O-Rings [2]
210N [1] CLD 23 NBR
212N [1] C. HOT EPDM

[1] Certified for a maximum surface area to volume ratio of 2.0 sq. in./L.
[2] Only products bearing the NSF Mark on the product, product packaging, and/or
    documentation shipped with the product are Certified.



Facility : Litchfield, MN

Joining and Sealing Materials

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Gasket/Sealing Materials
515CG[2] [1] C. HOT PVDF
534DF [1] CLD 23 NBR
534HC[2] [1] CLD 23 NBR
536EG[11] [4] CLD 23 NBR
558CH[3] [4] C. HOT EPDM
558CK[2] [1] C. HOT EPDM
558CM[2] [1] C. HOT EPDM
558EC[3] [4] C. HOT EPDM
559GT[2] [1] C. HOT EPDM
559N[5] [6] C. HOT EPDM
559PE[7] [8] C. HOT EPDM
559TM[9] [1] C. HOT EPDM
559YU[2] [1] C. HOT EPDM
560CF[2] [1] C. HOT EPDM
560RJ[10] [6] C. HOT EPDM
560YH [1] C. HOT EPDM
561NZ[2] [1] C. HOT EPDM
561TX[2] [1] C. HOT EPDM
565CZ [1] C. HOT EPDM
574J[2] [1] C. HOT HNBR
574TA[2] [1] C. HOT HNBR
76155 [1] C. HOT SLC
76156 [1] C. HOT SLC
76157 [1] C. HOT SLC
76187D [1] C. HOT SLC
Quniton 560CF[2] [1] C. HOT EPDM
Quniton(R) 558CH[3] [4] C. HOT EPDM
Quniton[R] 558EC[3] [4] C. HOT EPDM
Quniton[R] 559PE[7] [8] C. HOT EPDM

[1] Certified for a maximum surface area to volume ratio of 2.0 sq. in./L.
[2] This product has also been evaluated for use in Mechanical Plumbing Device applications
    with a maximum surface area to volume ratio of 2.0 sq. in./L.
[3] This product was also evaluated for use in Mechanical Plumbing Device applications with
    a maximum use restriction of 3.0 sq. in./L.
[4] Certified for a maximum surface area to volume ratio of 14.0 square inches/L.
[5] This product has also been evaluated for use in Mechanical Plumbing Device applications
    with a maximum use restriction of 1.0 sq. in./L.
[6] Certified for a maximum surface area to volume ratio of 4.0 sq. in./L.
[7] This product has also been evaluated for use in Mechanical Plumbing Device applications
    with a maximum use restriction of 8 sq. in./L.
[8] Certified for a maximum surface area to volume ratio of 14 sq. in./L.
[9] This product has also been evaluated for use in Mechanical Plumbing Device applications
    with a maximum use restriction of 4 sq. in./L.
[10] This product has also been evaluated for use in Mechanical Plumbing Device applications
     with a maximum use restriction of 2.5 sq. in./L.
[11] This product has also been evaluated for use in Mechanical Plumbing Device applications
     with a maximum use restriction of 4 square inches/L.

O-Rings
515CG[2] [1] C. HOT PVDF
536EG[11] [4] C. HOT NBR
574J[2] [1] C. HOT HNBR
76187D [1] C. HOT SLC

[1] Certified for a maximum surface area to volume ratio of 2.0 sq. in./L.
[2] This product has also been evaluated for use in Mechanical Plumbing Device applications
    with a maximum surface area to volume ratio of 2.0 sq. in./L.
[4] Certified for a maximum surface area to volume ratio of 14.0 square inches/L.
[11] This product has also been evaluated for use in Mechanical Plumbing Device applications
     with a maximum use restriction of 4 square inches/L.

NOTE: Only products manufactured at an NSF authorized facility and bearing the NSF Mark are
      considered Certified.


Facility : Ashtabula, OH

Joining and Sealing Materials

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Gasket/Sealing Materials
558CH[1] [2] C. HOT EPDM
558CK[3] [4] C. HOT EPDM
558EC[1] [2] C. HOT EPDM
559GT[3] [4] C. HOT EPDM
559PE[5] [2] C. HOT EPDM

[1] This product was also evaluated for use in Mechanical Plumbing Device applications with
    a maximum use restriction of 3.0 sq. in./L.
[2] Certification requested for a maximum surface area to volume ratio of 14.0 square
    inches/L.
[3] This product has also been evaluated for use in Mechanical Plumbing Device applications
    with a maximum use restriction of 2.0 square inches/L
[4] Certification requested for a maximum surface area to volume ratio of 2.0 square
    inches/liter.
[5] This product has also been evaluated for use in Mechanical Plumbing Device applications
    with a maximum use restriction of 5.5 sq.in./L



Facility : Guangdong, China

Joining and Sealing Materials

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Gasket/Sealing Materials
217AB[1] [2] C. HOT SLC
76155 [3] C. HOT SLC
76156 [3] C. HOT SLC
76157 [3] C. HOT SLC

[1] This product has been evaluated for use in Mechanical Plumbing Device applications with
    a maximum use restriction of 4.0 sq. in./L.
[2] Certified for a maximum surface area to volume ratio of 4.0 sq. in./L.
[3] Certified for a maximum surface area to volume ratio of 2.0 sq. in./L.



Facility : Jiangsu, China

Joining and Sealing Materials

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Gasket/Sealing Materials
366SM [1] C. HOT NBR
515CG[2] [1] C. HOT PVDF
534HC[2] [1] CLD 23 NBR
536EG[3] [4] CLD 23 NBR
557WE[5] [6] C. HOT EPDM
557WG[5] [6] C. HOT EPDM
557WM[5] [6] C. HOT EPDM
558CH[7] [4] C. HOT EPDM
558CK[2] [1] C. HOT EPDM
558CM[2] [1] C. HOT EPDM
558EC[7] [4] C. HOT EPDM
559GT[2] [1] C. HOT EPDM
559N[8] [9] C. HOT EPDM
559PE[7] [4] C. HOT EPDM
559TM[3] [1] C. HOT EPDM
559YU[2] [1] C. HOT EPDM
560CF[2] [1] C. HOT EPDM
560RJ[10] [9] C. HOT EPDM
560YH [1] C. HOT EPDM
561NZ[2] [1] C. HOT EPDM
561TX[2] [1] C. HOT EPDM
565CZ [1] C. HOT EPDM
71105B[2] [1] CLD 23 SLC
76155 [1] C. HOT SLC
76156 [1] C. HOT SLC
76157 [1] C. HOT SLC
862KA[4] [7] C. HOT EPDM
Quniton[R] 559PE[7] [4] C. HOT EPDM
Quniton[R] 560CF[2] [1] C. HOT EPDM

[1] Certified for a maximum surface area to volume ratio of 2.0 sq. in./L.
[2] This product has also been evaluated for use in Mechanical Plumbing Device applications
    with a maximum use restriction of 2.0 sq. in./L.
[3] This product has also been evaluated for use in Mechanical Plumbing Device applications
    with a maximum use restriction of 3.63 sq. in./L.
[4] Certified for a maximum surface area to volume ratio of 14.0 sq. in./L.
[5] This product has also been evaluated for use in Mechanical Plumbing Device applications
    with a maximum use restriction of 10 square inches/L.
[6] Certified for a maximum surface area to volume ratio of 10 square inches/L.
[7] This product has also been evaluated for use in Mechanical Plumbing Device applications
    with a maximum use restriction of 8.0 sq. in./L.
[8] This product has also been evaluated for use in Mechanical Plumbing Device applications
    with a maximum use restriction of 1.0 sq. in./L.
[9] Certified for a maximum surface area to volume ratio of 4.0 sq. in./L.
[10] This product has also been evaluated for use in Mechanical Plumbing Device applications
     with a maximum use restriction of 2.5 sq. in./L.

O-Rings
515CG[2] [1] C. HOT PVDF
536EG[3] [4] CLD 23 NBR
557WE[5] [6] C. HOT EPDM
557WG[5] [6] C. HOT EPDM
557WM[5] [6] C. HOT EPDM

[1] Certified for a maximum surface area to volume ratio of 2.0 sq. in./L.
[2] This product has also been evaluated for use in Mechanical Plumbing Device applications
    with a maximum use restriction of 2.0 sq. in./L.
[3] This product has also been evaluated for use in Mechanical Plumbing Device applications
    with a maximum use restriction of 3.63 sq. in./L.
[4] Certified for a maximum surface area to volume ratio of 14.0 sq. in./L.
[5] This product has also been evaluated for use in Mechanical Plumbing Device applications
    with a maximum use restriction of 10 square inches/L.
[6] Certified for a maximum surface area to volume ratio of 10 square inches/L.



Facility : Reynosa, Tamaulipas, Mexico

Joining and Sealing Materials

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Gasket/Sealing Materials
366SM [1] C. HOT NBR
515CG[2] [1] C. HOT PVDF
534DF [1] CLD 23 NBR
534HC[2] [1] CLD 23 NBR
536EG[3] [4] CLD 23 NBR
557WE[5] [6] C. HOT EPDM
557WG[5] [6] C. HOT EPDM
557WM[5] [6] C. HOT EPDM
558BM [1] CLD 23 EPDM
558CH[3] [4] C. HOT EPDM
558CK[2] [1] C. HOT EPDM
558CM[2] [1] C. HOT EPDM
558EC[3] [4] C. HOT EPDM
559GT[2] [1] C. HOT EPDM
559N[7] [8] C. HOT EPDM
559PE[2] [4] C. HOT EPDM
559TM[2] [1] C. HOT EPDM
559YU[2] [1] C. HOT EPDM
560CF[2] [1] C. HOT EPDM
560RJ[9] [8] C. HOT EPDM
560YH [1] C. HOT EPDM
561NZ[2] [1] C. HOT EPDM
561TX[2] [1] C. HOT EPDM
565CZ C. HOT EPDM
71105B[2] [1] CLD 23 SLC
912V[11] [10] C. HOT EPDM
Quniton[R] 558CH[3] [4] C. HOT EPDM
Quniton[R] 558EC[3] [4] C. HOT EPDM
Quniton[R] 559PE[2] [4] C. HOT EPDM
Quniton[R] 560CF[2] [1] C. HOT EPDM

[1] Certified for a maximum surface area to volume ratio of 2.0 sq. in./L.
[2] This product has also been evaluated for use in Mechanical Plumbing Device applications
    with a maximum use restriction of 2.0 sq. in./L.
[3] This product was also evaluated for use in Mechanical Plumbing Device applications with
    a maximum use restriction of 4.0 sq. in./L.
[4] Certified for a maximum surface area to volume ratio of 14.0 sq. in./L.
[5] This product has also been evaluated for use in Mechanical Plumbing Device applications
    with a maximum use restriction of 10 square inches/L.
[6] Certified for a maximum surface area to volume ratio of 10 square inches/L.
[7] This product has also been evaluated for use in Mechanical Plumbing Device applications
    with a maximum use restriction of 1.0 sq. in./L.
[8] Certified for a maximum surface area to volume ratio of 4.0 sq. in./L.
[9] This product has also been evaluated for use in Mechanical Plumbing Device applications
    with a maximum use restriction of 2.5 sq. in./L.
[10] Certified for a maximum surface area to volume ratio of 5.0 square inches/L.
[11] This product has also been evaluated for use in Mechanical Plumbing Device applications
     with a maximum use restriction of 5.0 square inches/L.

O-Rings
515CG[2] [1] C. HOT PVDF
536EG[3] [4] C. HOT NBR
557WE[5] [6] C. HOT EPDM
557WG[5] [6] C. HOT EPDM
557WM[5] [6] C. HOT EPDM
912V[11] [10] C. HOT EPDM

[1] Certified for a maximum surface area to volume ratio of 2.0 sq. in./L.
[2] This product has also been evaluated for use in Mechanical Plumbing Device applications
    with a maximum use restriction of 2.0 sq. in./L.
[3] This product was also evaluated for use in Mechanical Plumbing Device applications with
    a maximum use restriction of 4.0 sq. in./L.
[4] Certified for a maximum surface area to volume ratio of 14.0 sq. in./L.
[5] This product has also been evaluated for use in Mechanical Plumbing Device applications
    with a maximum use restriction of 10 square inches/L.
[6] Certified for a maximum surface area to volume ratio of 10 square inches/L.
[10] Certified for a maximum surface area to volume ratio of 5.0 square inches/L.
[11] This product has also been evaluated for use in Mechanical Plumbing Device applications
     with a maximum use restriction of 5.0 square inches/L.

NOTE: Only products manufactured at an NSF authorized facility and bearing the NSF Mark are
      considered Certified.


 
Trelleborg Sealing Solutions US Inc. 
2509 Bremer Road
Fort Wayne, IN 46803 
United States 
800-323-0496 
260-749-9631


Facility : Shanghai, China

Joining and Sealing Materials

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Gasket/Sealing Materials
E6H11 [1] C. HOT EPDM
E7H10[2] [1] C. HOT EPDM
E7H17[3] [1] C. HOT EPDM
E7H19 [4] C. HOT EPDM
E8W02[3] [1] C. HOT EPDM
S6W12[5] [G] [1] C. HOT SLC
S7W11[5] [G] [1] C. HOT SLC
VCZ80[6] [1] C. HOT FE

[1] Certified for a maximum surface area to volume ratio of 2.0 sq. in./L.
[2] This product has also been evaluated for use in Mechanical Plumbing Device applications
    with a maximum use restriction of 1.5 sq. in./L.
[3] This product has also been evaluated for use in Mechanical Plumbing Device applications
    with a maximum use restriction of 0.9 sq. in./L.
[4] Certified for a maximum surface area to volume ratio of 1 sq. in./L.
[5] This product has also been evaluated for use in Mechanical Plumbing Device applications
    with a maximum use restriction of 2.0 sq. in./L.
[6] This product has also been evaluated for use in Mechanical Plumbing Device applications
    with a maximum use restriction of 0.2 sq. in./L.
[G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for
    “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state
    laws and the U.S. Safe Drinking Water Act.

    

O-Rings
E6H11 [1] C. HOT EPDM
E7H10[2] [1] C. HOT FE
E7H17[3] [1] C. HOT EPDM
E8W02[3] [1] C. HOT EPDM
S6W12[5] [G] [1] C. HOT SLC
S7W11[5] [G] [1] C. HOT SLC
VCZ80[6] [1] C. HOT FE

[1] Certified for a maximum surface area to volume ratio of 2.0 sq. in./L.
[2] This product has also been evaluated for use in Mechanical Plumbing Device applications
    with a maximum use restriction of 1.5 sq. in./L.
[3] This product has also been evaluated for use in Mechanical Plumbing Device applications
    with a maximum use restriction of 0.9 sq. in./L.
[5] This product has also been evaluated for use in Mechanical Plumbing Device applications
    with a maximum use restriction of 2.0 sq. in./L.
[6] This product has also been evaluated for use in Mechanical Plumbing Device applications
    with a maximum use restriction of 0.2 sq. in./L.
[G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for
    “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state
    laws and the U.S. Safe Drinking Water Act.

    



 
Trelleborg Sealing Solutions US Inc. 
2509 Bremer Road
Fort Wayne, IN 46803 
United States 
800-323-0496 
260-748-5774


Facility : Tatu Taichung, Taiwan

Joining and Sealing Materials

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Gasket/Sealing Materials
E6W01 [2] C. HOT EPDM
E7W12 [2] C. HOT EPDM
E8W05 [2] C. HOT EPDM
N6W01[3] [1] C. HOT NBR
N7W05[3] [1] C. HOT NBR
N8W06[3] [1] C. HOT NBR

[1] Certified for a maximum surface area to volume ratio of 0.5 sq. in./L.
[2] Certified for a maximum surface area to volume ratio of 2.0 sq. in./L.
[3] This product has also been evaluated for use in Mechanical Plumbing Device applications
    with a maximum use restriction of 0.1 sq. in./L.

O-Rings
E6W01 [2] C. HOT EPDM
E7W12 [2] C. HOT EPDM
E8W05 [2] C. HOT EPDM
N6W01[3] [1] C. HOT NBR
N7W05[3] [1] C. HOT NBR
N8W06[3] [1] C. HOT NBR

[1] Certified for a maximum surface area to volume ratio of 0.5 sq. in./L.
[2] Certified for a maximum surface area to volume ratio of 2.0 sq. in./L.
[3] This product has also been evaluated for use in Mechanical Plumbing Device applications
    with a maximum use restriction of 0.1 sq. in./L.



 
Trelleborg Sealing Solutions US Inc. 
2509 Bremer Road
Fort Wayne, IN 46803 
United States 
800-323-0496 
260-748-5774


Facility : Zhongshan City, China

Joining and Sealing Materials

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Gasket/Sealing Materials
E7W09[1] [2] C. HOT EPDM
E7W10 [2] C. HOT EPDM
E7W11[3] [2] C. HOT EPDM
N7W13[4] [2] D. HOT NBR
S7W03 [2] C. HOT SLC

[1] This product has also been evaluated for use in Mechanical Plumbing Device applications
    with a maximum surface area to volume ratio of 0.4 sq. in./L.
[2] Certified for a maximum surface area to volume ratio of 2.0 sq. in./L.
[3] This product has also been evaluated for use in Mechanical Plumbing Device
    applications with a maximum surface area to volume ratio of 2.0 sq. in./L.
[4] This product has also been evaluated for use in Mechanical Plumbing Device applications
    with a maximum surface area to volume ratio of 0.3 sq. in./L.

O-Rings
E7W09[1] [2] C. HOT EPDM
E7W10 [2] C. HOT EPDM
E7W11[3] [2] C. HOT EPDM
N7W13[4] [2] D. HOT NBR
S7W03 [2] C. HOT SLC

[1] This product has also been evaluated for use in Mechanical Plumbing Device applications
    with a maximum surface area to volume ratio of 0.4 sq. in./L.
[2] Certified for a maximum surface area to volume ratio of 2.0 sq. in./L.
[3] This product has also been evaluated for use in Mechanical Plumbing Device
    applications with a maximum surface area to volume ratio of 2.0 sq. in./L.
[4] This product has also been evaluated for use in Mechanical Plumbing Device applications
    with a maximum surface area to volume ratio of 0.3 sq. in./L.


Mechanical Plumbing Devices

Trade Designation      

Gasket/Sealing Materials
E7W10[1]      

[1] Certified for a maximum surface area to volume ratio of 2.0 sq. in./L.

O-Rings
E7W10[1]      

[1] Certified for a maximum surface area to volume ratio of 2.0 sq. in./L.



 
Trelleborg Sealing Solutions US Inc. 
2509 Bremer Road
Fort Wayne, IN 46803 
United States 
800-323-0496 
260-748-5774


Facility : Viadanica (BG), Italy

Joining and Sealing Materials

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Gasket/Sealing Materials [G]
N7072 [1] [2] D. HOT NBR

[1] This product has also been evaluated for use in Mechanical Plumbing Device applications
    with a maximum use restriction of 2.0 sq. in./L.
[2] Certified for a maximum suface area to volume ratio of 20 sq. in./L.
[G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for
    “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state
    laws and the U.S. Safe Drinking Water Act.

    

O-Rings [G]
N7072 [1] [2] D. HOT NBR

[1] This product has also been evaluated for use in Mechanical Plumbing Device applications
    with a maximum use restriction of 2.0 sq. in./L.
[2] Certified for a maximum suface area to volume ratio of 20 sq. in./L.
[G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for
    “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state
    laws and the U.S. Safe Drinking Water Act.

    



 
Trelleborg Sealing Solutions US Inc. 
2509 Bremer Road
Fort Wayne, IN 46803 
United States 
800-3230-496 
260-748-5774


Facility : # 1 Taiwan

Joining and Sealing Materials

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Gasket/Sealing Materials
E7W07 [1] C. HOT EPDM

[1] Certified for a maximum surface area to volume ratio of 2.0 sq. in./L.



 
Trelleborg Sealing Solutions US Inc. 
2509 Bremer Road
Fort Wayne, IN 46803 
United States 
800-323-0496 
260-748-5774


Facility : # 1 China

Mechanical Plumbing Devices

Trade Designation      

Gasket/Sealing Materials[1]
E7W16      

[1] Certified for a maximum surface area to volume ratio of 2.0 square inches/liter.

O-Rings[1]
E7W16      

[1] Certified for a maximum surface area to volume ratio of 2.0 square inches/liter.



 
TRI-MATIC AG 
Bösch 82
6331 Hünenberg ZG 
Switzerland 
41 41 780 2222
Visit this company's website


Facility : Hünenberg, Switzerland

Mechanical Devices

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Valves[G]
EcoReg® 1/4" CLD 23 MLTPL

[G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for
    “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state
    laws and the U.S. Safe Drinking Water Act.

    



 
Tribal Manufacturing, Inc. 
450 Leggitt Road
Marshall, MI 49068 
United States 
269-781-3901
Visit this company's website


Facility : Marshall, MI

Mechanical Devices

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Backflow Preventers
G-784 Backflow Preventer 1/2" x 1/2" CLD 23 MLTPL
G-784-10A Backflow Preventer 1/2" x 1/2" CLD 23 MLTPL
G-784-13A Backflow Preventer 3/4" x 1/2" CLD 23 MLTPL
G-784-8A Water Fill Assembly 1/2" x 1/2" CLD 23 MLTPL
G-784-9A Backflow Preventer 1/2" x 1/2" CLD 23 MLTPL

[1] Certified as a component of a manifold for a maximum of 22 adapters per liter for cold
    applications and a maximum of 16 adapters per liter for hot applications.

Pipes and Related Products

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Fittings[G]
Connectors (PEX barb x PEX barb) 3/4" – 1 1/4" C. HOT BRASS
F61E106Z 3/4" – 1 1/4" C. HOT BRASS
F61E108Z 3/4" – 1 1/4" C. HOT BRASS
F61E43Z 3/4" – 1 1/4" C. HOT BRASS
F61E63Z 3/4" – 1 1/4" C. HOT BRASS
F61E64Z 3/4" – 1 1/4" C. HOT BRASS
F61E84Z 3/4" – 1 1/4" C. HOT BRASS
F61E86Z 3/4" – 1 1/4" C. HOT BRASS

[G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for
    “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state
    laws and the U.S. Safe Drinking Water Act.

    



Facility : Chesnee, SC

Pipes and Related Products

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Fittings[G]
(109-2) LFA-710 Pipe Square Head Plug 1/8" D. HOT BRASS
(109-4) LFA-737 Pipe Square Head Plug 1/4" D. HOT BRASS
(109-6) LFA-773 Pipe Square Head Plug 3/8" D. HOT BRASS
(110-12-8) LFA-870 Pipe Bushing MIP X FIP 3/4" x 1/2" D. HOT BRASS
(110-6-4) LFA-778 Pipe Bushing MIP X FIP 3/8" x 1/4" D. HOT BRASS
(110-8-4) LFA-827 Pipe Bushing MIP X FIP 1/2" x 1/4" D. HOT BRASS
(110-8-6) LFA-828 Pipe Bushing MIP X FIP 1/2" x 3/8" D. HOT BRASS
(113-12) LFA-878 Pipe Nipple 3/4" x 1-1/2" D. HOT BRASS
(113-12) LFA-879 Pipe Nipple 3/4" x 2" D. HOT BRASS
(113-12) LFA-881 Pipe Nipple 3/4" x 3" D. HOT BRASS
(113-12) LFA-883 Pipe Nipple 3/4" x 4" D. HOT BRASS
(113-16) LFA-915 Pipe Nipple 1" x cl D. HOT BRASS
(113-16) LFA-917 Pipe Nipple 1" x 2" D. HOT BRASS
(113-2) LFA-715 Pipe Nipple 1/8" x cl D. HOT BRASS
(113-2) LFA-716 Pipe Nipple 1/8" x 1-1/2" D. HOT BRASS
(113-2) LFA-717 Pipe Nipple 1/8" x 2" D. HOT BRASS
(113-4) LFA-740 Pipe Nipple 1/4" x cl D. HOT BRASS
(113-4) LFA-741 Pipe Nipple 1/4" x 1-1/2" D. HOT BRASS
(113-4) LFA-742 Pipe Nipple 1/4" x 2" D. HOT BRASS
(113-4) LFA-744 Pipe Nipple 1/4" x 3" D. HOT BRASS
(113-4) LFA-746 Pipe Nipple 1/4" x 4" D. HOT BRASS
(113-6) LFA-785 Pipe Nipple 3/8" x cl D. HOT BRASS
(113-6) LFA-786 Pipe Nipple 3/8" x 1-1/2" D. HOT BRASS
(113-6) LFA-787 Pipe Nipple 3/8" x 2" D. HOT BRASS
(113-6) LFA-788 Pipe Nipple 3/8" x 2-1/2" D. HOT BRASS
(113-6) LFA-789 Pipe Nipple 3/8" x 3" D. HOT BRASS
(113-6) LFA-791 Pipe Nipple 3/8" x 4" D. HOT BRASS
(113-8) LFA-835 Pipe Nipple 1/2" x cl D. HOT BRASS
(113-8) LFA-836 Pipe Nipple 1/2" x 1-1/2" D. HOT BRASS
(113-8) LFA-837 Pipe Nipple 1/2" x 2" D. HOT BRASS
(113-8) LFA-838 Pipe Nipple 1/2" x 2-1/2" D. HOT BRASS
(113-8) LFA-841 Pipe Nipple 1/2" x 4" D. HOT BRASS
(113-8) LFA-843 Pipe Nipple 1/2" x 5" D. HOT BRASS
(113-8) LFA-845 Pipe Nipple 1/2" x 6" D. HOT BRASS
(113-CP-6) LFACP-787 Pipe Nipple 3/8" x 2" D. HOT BRASS
(113-CP-6) LFACP-791 Pipe Nipple 3/8" x 4" D. HOT BRASS
(113-CP-8) LFACP-837 Pipe Nipple 1/2" X 2" D. HOT BRASS
(113-CP-8) LFACP-839 Pipe Nipple 1/2" x 3" D. HOT BRASS
(122-12) LFA-875 Pipe Hex Nipple 3/4" D. HOT BRASS
(122-2) LFA-714 Pipe Hex Nipple 1/8" D. HOT BRASS
(122-6) LFA-783 Pipe Hex Nipple 3/8" D. HOT BRASS
(122-8) LFA-833 Pipe Hex Nipple 1/2" D. HOT BRASS
(39-P-6) LFA-159 Flare Plug 3/8" D. HOT BRASS
(39-P-8) LFA-259 Flare Plug 1/2" D. HOT BRASS
(4/6/6280) LFA-154 Tube X Fine Thrd Flare Adapter 1/4" x 3/8" D. HOT BRASS
(40-C-10) LFA-342 Flare Cap 5/8" D. HOT BRASS
(40-C-4) LFA-63 Flare Cap 1/4" D. HOT BRASS
(40-C-6) LFA-163 Flare Cap 3/8" D. HOT BRASS
(40-C-8) LFA-263 Flare Cap 1/2" D. HOT BRASS
(42-4) LFA-65 Flare To Flare Union 1/4" D. HOT BRASS
(42-6) LFA-165 Flare To Flare Union 3/8" D. HOT BRASS
(42-R-8-6) LFA-268 Flare To Flare Reducing Union 1/2" x 3/8" D. HOT BRASS
(44-6) LFA-168 Flare Tee 3/8" x 3/8" x 3/8" D. HOT BRASS
(44-8) LFA-271 Flare Tee 1/2" x 1/2" x 1/2" D. HOT BRASS
(46-6-6) LFA-176 Flare X FIP Coupling 3/8" x 3/8" D. HOT BRASS
(46-6-8) LFA-177 Flare X FIP Coupling 3/8" x 1/2" D. HOT BRASS
(46-8-6) LFA-274 Flare X FIP Coupling 1/2" x 3/8" D. HOT BRASS
(46-8-8) LFA-273 Flare X FIP Coupling 1/2" x 1/2" D. HOT BRASS
(48-10-12) LFA-371 Flare X MIP Half Union 5/8" x 3/4" D. HOT BRASS
(48-10-8) LFA-370 Flare X MIP Half Union 5/8" x 1/2" D. HOT BRASS
(48-12-12) LFA-472 Flare x MIP Half Union 3/4" x 3/4" D. HOT BRASS
(48-4-4) LFA-80 Flare X MIP Half Union 1/4" x 1/4" D. HOT BRASS
(48-6-4) LFA-182 Flare X MIP Half Union 3/8" x 1/4" D. HOT BRASS
(48-6-6) LFA-183 Flare X MIP Half Union 3/8" x 3/8" D. HOT BRASS
(48-6-8) LFA-184 Flare X MIP Half Union 3/8" x 1/2" D. HOT BRASS
(48-8-6) LFA-276 Flare X MIP Half Union 1/2" x 3/8" D. HOT BRASS
(48-8-8) LFA-277 Flare X MIP Half Union 1/2" x 1/2" D. HOT BRASS
(49-6-6) LFA-186 Flare X MIP Elbow 3/8" x 3/8" D. HOT BRASS
(566-6-8) LFA-120 Comp x Sweat Adapter 3/8" x 1/2" D. HOT BRASS
(6/6/6280) LFA-156 Tube X Fine Thrd Flare Adapter 3/8" x 3/8" D. HOT BRASS
(61-CX-10) LFA-305 Compression Cap 5/8" D. HOT BRASS
(61-CX-4) LFA-5 Compression Cap 1/4" D. HOT BRASS
(61-CX-6) LFA-105 Compression Cap 3/8" D. HOT BRASS
(61-CX-8) LFA-205 Compression Cap 1/2" D. HOT BRASS
(62-6) LFA-110C Comp Union (5 Pack) 3/8" D. HOT BRASS
(62-FM-6-4) LFA-157 F.Comp X Tube Adapter 3/8" x 1/4" D. HOT BRASS
(62-FM-7-6) LFA-200 F.Comp X Tube Adapter 7/16" x 3/8" D. HOT BRASS
(62-FM-8-6) LFA-230 F. Comp X Tube Adapter 1/2” x 3/8” D. HOT BRASS
(62SWV-6) LFA-157A Fem Comp x Fem Comp 3/8" x 3/8" D. HOT MLTPL
(962-10) LFA-310 Ander-Lign Comp Union W/Inst 5/8" D. HOT BRASS
(962-4) LFA-10 Ander-Lign Comp Union W/Inst 1/4" D. HOT BRASS
(962-6) LFA-110 Ander-Lign Comp Union W/Inst 3/8" D. HOT BRASS
(962-8) LFA-210 Ander-Lign Comp Union W/Inst 1/2" D. HOT BRASS
(962-R-10-6) LFA-309 Ander-Lign Comp Reducing Union W/Inst 5/8" x 3/8" D. HOT BRASS
(962-R-6-4) LFA-109 Ander-Lign Comp Reducing Union W/Inst 3/8" x 1/4" D. HOT BRASS
(964-4) LFA-12 Ander-Lign Comp Tee W/Inst 1/4" D. HOT BRASS
(964-6) LFA-114 Ander-Lign Comp Tee W/Inst 3/8" D. HOT BRASS
(964-8) LFA-214 Ander-Lign Comp Tee W/Inst 1/2" D. HOT BRASS
(964-R-6-6-4) LFA-113 Ander-Lign Comp Red.Tee W/Inst 3/8" x 3/8" x 1/4" D. HOT BRASS
(965-4) LFA-14 Ander-Lign Comp Elbow W/Inst 1/4" D. HOT BRASS
(965-6) LFA-115 Ander-Lign Comp Elbow W/Inst 3/8" D. HOT BRASS
(966-4-4) LFA-16 Ander-Lign Comp X FIP Coupling W/Inst 1/4" x 1/4" D. HOT BRASS
(966-4-6) LFA-18 Ander-Lign Comp X FIP Coupling W/Inst 1/4" x 3/8" D. HOT BRASS
(966-4-8) LFA-19 Ander-Lign Comp X FIP Coupling W/Inst 1/4" x 1/2" D. HOT BRASS
(966-6-4) LFA-116 Ander-Lign Comp X FIP Coupling W/Inst 3/8" x 1/4" D. HOT BRASS
(966-6-6) LFA-117Ander-Lign Comp X FIP Coupling W/Inst 3/8" x 3/8" D. HOT BRASS
(966-6-8) LFA-118 Ander-Lign Comp X FIP Coupling W/Inst 3/8" x 1/2" D. HOT BRASS
(966-8-8) LFA-218 Ander-Lign Comp x FIP 1/2" X 1/2" D. HOT BRASS
(968-10-8) LFA-324 Ander-Lign Comp X MIP Connector W/Ins 5/8" x 1/2" D. HOT BRASS
(968-4-2) LFA-22 Ander-Lign Comp X MIP Connector W/Ins 1/4" x 1/8" D. HOT BRASS
(968-4-4) LFA-23 Ander-Lign Comp X MIP Connector W/Ins 1/4" x 1/4" D. HOT BRASS
(968-4-8) LFA-25 Ander-Lign Comp X MIP Connector W/Ins 1/4" x 1/2" D. HOT BRASS
(968-6-12) LFA-125 Ander-Lign Comp X FIP Coupling W/Inst 1/4" x 1/2" D. HOT BRASS
(968-6-4) LFA-122 Ander-Lign Comp X MIP Connector W/Ins 3/8" x 1/4" D. HOT BRASS
(968-6-6) LFA-123 Ander-Lign Comp X MIP Connector W/Ins 3/8" x 3/8" D. HOT BRASS
(968-6-8) LFA-124 Ander-Lign Comp X MIP Connector W/Ins 3/8"x 1/2" D. HOT BRASS
(968-8-6) LFA-220 Ander-Lign Comp X MIP Connector W/Ins 1/2" x 3/8" D. HOT BRASS
(968-8-8) LFA-221 Ander-Lign Comp X MIP Connector W/Ins 1/2" x 1/2" D. HOT BRASS
(969-4-2) LFA-29 Ander-Lign Comp X MIP Elbow W/Inst 1/4" x 1/8" D. HOT BRASS
(969-4-4) LFA-30 Ander-Lign Comp X MIP Elbow W/Inst 1/4" x 1/4" D. HOT BRASS
(969-6-6) LFA-129 Ander-Lign Comp X MIP Elbow W/Inst 3/8" x 3/8" D. HOT BRASS
(969-6-8) LFA-130 Ander-Lign Comp X MIP Elbow W/Inst 3/8" x 1/2" D. HOT BRASS
(969-8-8) LFA-223 Ander-Lign Comp X MIP Elbow W/Inst 1/2" x 1/2" D. HOT BRASS
(C109-12) LFA-869 Pipe Square Head Plug 3/4" D. HOT BRASS
(GH3-12-8) LFA-663 BRASS MIP X MGH ADAPTER 3/4" x 1/2" D. HOT BRASS
(GH6-12-8) LFA-677 BRASS FGH X MIP ADAPTER 3/4" x 1/2" D. HOT BRASS
(GHR4-12-4) LFA-696 BRASS FGH X 1/4"" COMPRESSION 3/4" x 1/4" D. HOT BRASS
(RB113-2) LFA-719 Pipe Nipple 1/8" X 3" D. HOT BRASS
(RB113-2) LFA-721 Pipe Nipple 1/8" x 4" D. HOT BRASS
WPEX 3/8" - 1" C. HOT BRASS

[G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for
    “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state
    laws and the U.S. Safe Drinking Water Act.

    



 
Tribology Tech-Lube 
35 Old Dock Road
Yaphank, NY 11980 
United States 
800-569-1757 
631-345-3000


Facility : Yaphank, NY

Joining and Sealing Materials

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Lubricants[G]
Gruvlok Xtreme Lubricant™ >= 1/2" C. HOT SLC
Aqua Gel 61 >= 1/2" C. HOT SLC

[G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for
    “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state
    laws and the U.S. Safe Drinking Water Act.

    



 
Tricon Company Limited 
Churchill Roosevelt Highway 
Streatham Lodge 
Tunapuna 
Trinidad and Tobago 
868-226-1991


Facility : Tunapuna, Trinidad and Tobago

Pipes and Related Products

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Pipe[G]
Tricon >= 1/2" CLD 23 PVC

[G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for
    “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state
    laws and the U.S. Safe Drinking Water Act.

    



 
Trimble Water / Telog Instruments 
830 Canning Parkway
Victor, NY 14564 
United States 
888-835-6437 
585-742-3000
Visit this company's website


Facility : Devon, United Kingdom

Mechanical Devices

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Switches/Sensors[1] [G]
IFM-32 [3] CLD 23 MLTPL
IFM-32 [2] CLD 23 MLTPL

[1] Only products bearing the NSF Mark on the product, product packaging, and/or
    documentation shipped with the product are Certified.
[2] Certification for use in 4" - 80" pipe.
[3] Certified for use in 3" - 12" pipe.
[G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for
    “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state
    laws and the U.S. Safe Drinking Water Act.

    



 
Tripac Marketing Inc. 
475 Klug Circle
Corona, CA 92880 
United States 
951-280-4488
Visit this company's website


Facility : Golden, CO

Pipes and Related Products

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Dielectric Insulator[1] [2] [G]
ISOGUARD TP61™ Sealing/Isolating Gaskets 1/2" - 108" C. HOT MLTPL

[1] Product may be sold with Flange Isolation Kits, which do not have water contact.
[2] Certified for 1/8" retainer gaskets with EPDM sealing elements.
[G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for
    “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state
    laws and the U.S. Safe Drinking Water Act.

    



Facility : Houston, TX

Joining and Sealing Materials

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Gasket/Sealing Materials
TRIPAC NA61 [1] C. HOT PTFE

[1] Certified for a maximum surface area to volume ratio of 2.0 square inches/L.



 
Trojan Technologies 
3020 Gore Road
London, ON N5V 4T7 
Canada 
519-457-3400


Facility : London, Ontario, Canada

Mechanical Devices

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Ultra-Violet Reactors[1]
AQUAFINE™ LOGIC 4" - 10" CLD 23 MLTPL
AVANT™ 4" - 8" CLD 23 MLTPL
OPTIVENN™ 2" - 10" CLD 23 MLTPL
SWIFTBEVERAGE™ 4" - 20" CLD 23 MLTPL
TROJANUVFLEX™ 12" - 48" CLD 23 MLTPL
TROJANUVPHOX™ 4" - 20" CLD 23 MLTPL
TROJANUVSWIFT™ 12" - 30" CLD 23 MLTPL
TROJANUVSWIFT™ ECT 24" - 30" CLD 23 MLTPL
TROJANUVSWIFT™ SC 4" - 20" CLD 23 MLTPL
TROJANUVTORRENT™ 48" CLD 23 MLTPL
TROJANUVTORRENT™ ECT 48" CLD 23 MLTPL

[1] TROJANUVTORRENT™: Certified for a minimum flow of 2 million gallons per day (7,570,824
    L/day).
    TROJANUVFLEX™ 100: Certified for a minimum flow rate of 1.5 million gallons per day. 
    TROJANUVFLEX™ 200: Certified for a minimum flow rate of 2.8 million gallons per day.
    TROJANUVSWIFT™ 2L12: Certified for a minimum flow of 0.2 million gallons per day. 
    TROJANUVSWIFT™ 2L24, 4L24, 6L24, 8L24 and ECT 8L24: Certified for a minimum flow rate of
    1 million gallons per day.
    TROJANUVSWIFT™ 4L30, 6L30, 8L30, 10L30, 16L30, ECT 8L30, and ECT 16L30: Certified for a
    minimum flow of 3 million gallons per day.
    TROJANUVPHOX™,  TROJANUVSWIFT™ SC, SWIFTBEVERAGE™, and AQUAFINE™ LOGIC :  Certified for
    a minimum flow of 27,200 L/day.
    OPTIVENN™: Certified for a minimum flow of 115 per gallons per day (435 L/day).
    AVANT™: Certified for a minimum flow of 1152 gallons per day (4360 L/day).

NOTE: Only products bearing the NSF Mark on the product, product packaging, and/or
      documentation shipped with the product are Certified.


 
Trojan Technologies 
839 State Route 13
Cortland, NY 13045 
United States 
516-484-5400


Facility : 1A

Mechanical Devices

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Ultrafiltration Devices[1]
FX0620050080A00-CN 160 mm x 2200 mm CLD 23 MLTPL
FX0620050080B00-CN 160 mm x 2200 mm CLD 23 MLTPL
FX0620050080C00-CN 160 mm x 2200 mm CLD 23 MLTPL
FX0620050100A00-CN 160 mm x 2200 mm CLD 23 MLTPL
FX0620050100B00-CN 160 mm x 2200 mm CLD 23 MLTPL
FX0620050100C00-CN 160 mm x 2200 mm CLD 23 MLTPL

[1] Certified to a minimum daily flow rate of 5760 liters per day.



Facility : 2B

Mechanical Devices

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Ultrafiltration Devices[1]
FX0620050080A00-CN 160 mm x 2200 mm CLD 23 MLTPL
FX0620050080B00-CN 160 mm x 2200 mm CLD 23 MLTPL
FX0620050080C00-CN 160 mm x 2200 mm CLD 23 MLTPL
FX0620050100A00-CN 160 mm x 2200 mm CLD 23 MLTPL
FX0620050100B00-CN 160 mm x 2200 mm CLD 23 MLTPL
FX0620050100C00-CN 160 mm x 2200 mm CLD 23 MLTPL

[1] Certified to a minimum daily flow rate of 5760 liters per day



Facility : 3C

Mechanical Devices

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Ultrafiltration Devices[1]
FX0620050080A00-SN 160 mm x 2200 mm CLD 23 MLTPL
FX0620050080B00-SN 160 mm x 2200 mm CLD 23 MLTPL
FX0620050080C00-SN 160 mm x 2200 mm CLD 23 MLTPL
FX0620050100A00-SN 160 mm x 2200 mm CLD 23 MLTPL
FX0620050100B00-SN 160 mm x 2200 mm CLD 23 MLTPL
FX0620050100C00-SN 160 mm x 2200 mm CLD 23 MLTPL

[1] Certified to a minimum daily flow rate of 5760 liters per day



 
Trojan Technologies Corporation 
839 State Route 13
Cortland, NY 13045 
United States 
866-475-0115


Facility : Cortland, NY

Mechanical Devices

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Microfiltration Devices
UNA-620A[1] [2] 6 1/2" X 85" CLD 23 MLTPL
UNA-620A-ADA[1] [2] 6 1/2" X 85" CLD 23 MLTPL

[1] UNA-620A and UNA-620A-ADA are certified for a minimum daily flow of 27,254 Liters per
    day.
[2] UNA-620A and UNA-620A-ADA are flushed for 15 minutes at a flow rate of 5 gallons per
    minute with water treatment plant feed water or tap water.
[3] UNA-620C is certified for a minimum daily flow of 12,168 gallons per day.
[4] UNA-620C is flushed for 15 minutes at a flow rate of 5 gallons per minute with water
    treatment plant feed water or tap water.

Ultrafiltration Devices
Ultra60 UF Module MSA-620A[5] [6] 7" x 92" CLD 23 MLTPL

[5] Certified for a minimum daily flow of 11,520 liters.
[6] Product requires a 7 gpm flush with tap water for 15 minutes before use.

Microfiltration Devices
UNA-620C[3] [4] 6 1/2" X 85" CLD 23 MLTPL

[1] UNA-620A and UNA-620A-ADA are certified for a minimum daily flow of 27,254 Liters per
    day.
[2] UNA-620A and UNA-620A-ADA are flushed for 15 minutes at a flow rate of 5 gallons per
    minute with water treatment plant feed water or tap water.
[3] UNA-620C is certified for a minimum daily flow of 12,168 gallons per day.
[4] UNA-620C is flushed for 15 minutes at a flow rate of 5 gallons per minute with water
    treatment plant feed water or tap water.



 
TRU-FLOW Industrial Co., Ltd. 
No. 4, Yi Ming Street
Ta Fa Industrial Zone 
Ta Liao District, Kaohsiung City 
Taiwan 
886 7 787 1212
Visit this company's website


Facility : # 2 Taiwan

Pipes and Related Products

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Fittings[G]
45° ELBOW LR 304/304L 1/2" - 36" D. HOT SS
90° ELBOW LR 304/304L 1/2" - 36" D. HOT SS
90° ELBOW SR 304/304L 1" - 24" D. HOT SS
Caps 304/304L 3/4" - 24" D. HOT SS
Con-Red 304/304L 3/4"x1/2" - 36"x34" D. HOT SS
Ecc-Red 304/304L 3/4"x1/2" - 36"x34" D. HOT SS
Equal Tee 304/304L 1/2" - 24" D. HOT SS
Red Tee 304/304L 3/4"x1/2" - 24"x22" D. HOT SS
Stub End Type-A 304/304L 1/2" - 24" D. HOT SS
Stub End Type-B 304/304L 1/2" - 24" D. HOT SS
Stub End Type-C 304/304L 1/2" - 12" D. HOT SS
45° ELBOW LR 316/316L 1/2" - 36" CLD 23 SS
90° ELBOW LR 316/316L 1/2" - 36" CLD 23 SS
90° ELBOW SR 316/316L 1" - 24" CLD 23 SS
Caps 316/316L 3/4" - 24" CLD 23 SS
Con-Red 316/316L 3/4"x1/2" - 36"x34" CLD 23 SS
Ecc-Red 316/316L 3/4"x1/2" - 36"x34" CLD 23 SS
Equal Tee 316/316L 1/2" - 24" CLD 23 SS
Red Tee 316/316L 3/4"x1/2" - 24"x22" CLD 23 SS
Stub End Type-A 316/316L 1/2" - 24" CLD 23 SS
Stub End Type-B 316/316L 1/2" - 24" CLD 23 SS
Stub End Type-C 316/316L 1/2" - 12" CLD 23 SS

[G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for
    “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state
    laws and the U.S. Safe Drinking Water Act.

    

NOTE: Only products bearing the NSF Mark on the product, product packaging, and/or
      documentation shipped with the product are Certified.


 
Tsingshan Steel Pipe Co., Ltd. 
Xiaozhi Industrial Zone
Wenxi Town, Qingtian County 
Lishui, Zhejiang 323903 
China 
86 159 6876 5883


Facility : Lishui, Zhejiang, China

Pipes and Related Products

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Fittings[G]
Elbows 1/4" - 80" C. HOT SS
Flanges 1/4" - 80" C. HOT SS
Reducers 1/4" - 80" C. HOT SS
Tees 1/4" - 80" C. HOT SS

[G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for
    “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state
    laws and the U.S. Safe Drinking Water Act.

    

Pipe[G]
Stainless Steel Pipes 1/4" - 80" C. HOT SS

[G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for
    “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state
    laws and the U.S. Safe Drinking Water Act.

    



 
Tubacex Tubos Inoxidables, S.A.U. 
Tres Cruces, 8
Llodio, Álava 01400 
Spain 
34 94 671 93 00
Visit this company's website


Facility : Amurrio, Álava, Spain

Pipes and Related Products

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Pipe[G]
TX2 - TUBACEX - 1.4301 CFD 1/2" - 7" CLD 23 SS
TX2 - TUBACEX - 1.4306 CFD 1/2" - 7" CLD 23 SS
TX2 - TUBACEX - 1.4307 CFD 1/2" - 7" CLD 23 SS
TX2 - TUBACEX - 1.4401 CFD 1/2" - 7" CLD 23 SS
TX2 - TUBACEX - 1.4404 CFD 1/2" - 7" CLD 23 SS
TX2 - TUBACEX - 1.4410 CFD 1/2" - 7" CLD 23 SS
TX2 - TUBACEX - 1.4462 CD CFD 1/2" - 7" CLD 23 SS
TX2 - TUBACEX - 1.4501 CFD 1/2" - 7" CLD 23 SS
TX2 - TUBACEX - MT 304 CD 1/2" - 7" CLD 23 SS
TX2 - TUBACEX - MT 304L CD 1/2" - 7" CLD 23 SS
TX2 - TUBACEX - MT 316 - CF 1/2" - 7" CLD 23 SS
TX2 - TUBACEX - MT 316L - CF 1/2" - 7" CLD 23 SS
TX2 - TUBACEX - S30400 CD 1/2" - 7" CLD 23 SS
TX2 - TUBACEX - S30403 CD 1/2" - 7" CLD 23 SS
TX2 - TUBACEX - S31600 - CF 1/2" - 7" CLD 23 SS
TX2 - TUBACEX - S31603 - CF 1/2" - 7" CLD 23 SS
TX2 - TUBACEX - S31803 CD 1/2" - 7" CLD 23 SS
TX2 - TUBACEX - S31803 S32205 1.4462 - CD CFD 1/2" - 7" CLD 23 SS
TX2 - TUBACEX - S32205 CD 1/2" - 7" CLD 23 SS
TX2 - TUBACEX - S32750 1.4410 - CD CFD 1/2" - 7" CLD 23 SS
TX2 - TUBACEX - S32750 CD 1/2" - 7" CLD 23 SS