NSF Product and Service Listings

These NSF Official Listings are current as of Saturday, December 13, 2025 at 12:15 a.m. Eastern Time. Please contact NSF to confirm the status of any Listing, report errors, or make suggestions.

Alert: NSF is concerned about fraudulent downloading and manipulation of website text. Always confirm this information by clicking on the below link for the most accurate information: http://info.nsf.org/Certified/PwsComponents/Listings.asp?Company=02460&Standard=061&


NSF/ANSI/CAN 61
Drinking Water System Components - Health Effects

NOTE: Unless otherwise indicated for Materials, Certification is only for the Water Contact Material shown in the Listing. Click here for a list of Abbreviations used in these Listings. Click here for the definitions of Water Contact Temperatures denoted in these Listings. Products certified to NSF/ANSI/CAN 61 comply with the health effects criteria in NSF/ANSI/CAN 600.

 
PPG Protective and Marine Coatings 
11605 Vimy Ridge Road
Alexander, AR 72002 
United States 
501-235-9148


Facility : Alexander, AR

Protective (Barrier) Materials

    Water Water
  Water Contact Contact Contact
Trade Designation Size Restriction Temp Material

Coatings - Fittings
Amercoat 133[1] >= 4" CLD 23 EPOXY 

[1] Colors: Oxide red, white
    Number of Coats: 1-2
    Maximum Field Use Dry Film Thickness (in mils): 6 per coat; 10 total
    Recoat Cure Time and Temperature: 24 hours at 75°F
    Final Cure and Temperature: 14 days at 75°F
    Special Comments: Mix ratio of resin to cure is 4:1 by volume. Mix for 5 minutes, let
    stand for 10 minutes, then remix for 2-3 minutes before application. Scrape the sides of
    the can while mixing.

Coatings - Pipe
Amercoat 133[1] >= 30" CLD 23 EPOXY
Amerlock 2[2] >= 48" CLD 23 EPOXY
Novaguard 810[3] [4] CLD 23 EPOXY
Novaguard 810ER[3] [4] CLD 23 EPOXY
Novaguard 840[5] >= 42" CLD 23 EPOXY 

[1] Colors: Oxide red, white
    Number of Coats: 1-2
    Maximum Field Use Dry Film Thickness (in mils): 6 per coat; 10 total
    Recoat Cure Time and Temperature: 24 hours at 75°F
    Final Cure and Temperature: 14 days at 75°F
    Special Comments: Mix ratio of resin to cure is 4:1 by volume. Mix for 5 minutes, let
    stand for 10 minutes, then remix for 2-3 minutes before application. Scrape the sides of
    the can while mixing.
[2] Colors: Ivory, White, Medium Gray, RT-1805 Blue, Oxide Red, Black
    Number of Coats: 2-4
    Sequence of Coats: Any combination of listed colors
    Maximum Field Use Dry Thickness: 8 mils per coat; 18 mils total
    Maximum Thinner: 12% Amercoat #8 by volume (optional use is limited to tanks >= 250,000
    gallons)
    Recoat Cure Time and Temperature: 24 hours at 72° F
    Final Cure Time/Temperature: 10 days at 72° F for all end uses except tank >= 250,000
    gallons which has a final cure of 7 days at 72° F
    Special Comments: Mix ratio of Base:Cure is 1:1 by volume or 1.1:1 by weight. Use of
    Amercoat #8 Thinner is limited to tanks of 250,000 gallons or greater.
    Final Cure Temp: 10 days at 72° F for all end uses without thinner; 7 days at 72° F for
    tanks >= 250,000 gallons with Amercoat #8 thinner
[3] Number of Coats: 1-2
    Maximum Field Use Dry Film Thickness (in mils): 30
    Recoat Cure Time and Temperature: 24 hours at 70°F
    Final Cure Time and Temperature: See Listing Note.
[4] Certified for tanks >= 500 gallons, pipe >=22", and valves >=2" with a final cure of 72
    hours @ 77º F and tanks >= 250,000 gallons and valves >= 3/4" with a final cure of 10
    days at 40º F.
[5] Colors: Cream, Green
    Number of Coats:  1-2
    Maximum field use dry film thickness (in mils): 30
    Recoat cure time and temperature: 24 hours at 70°F
    Final cure time and temperature: 72 hours at 70°F
    Special Comments: Mix ratio of base to hardener is 4:1 by volume

Coatings - Pump
Amerlock 2[2] >= 4" CLD 23 EPOXY 

[2] Colors: Ivory, White, Medium Gray, RT-1805 Blue, Oxide Red, Black
    Number of Coats: 2-4
    Sequence of Coats: Any combination of listed colors
    Maximum Field Use Dry Thickness: 8 mils per coat; 18 mils total
    Maximum Thinner: 12% Amercoat #8 by volume (optional use is limited to tanks >= 250,000
    gallons)
    Recoat Cure Time and Temperature: 24 hours at 72° F
    Final Cure Time/Temperature: 10 days at 72° F for all end uses except tank >= 250,000
    gallons which has a final cure of 7 days at 72° F
    Special Comments: Mix ratio of Base:Cure is 1:1 by volume or 1.1:1 by weight. Use of
    Amercoat #8 Thinner is limited to tanks of 250,000 gallons or greater.
    Final Cure Temp: 10 days at 72° F for all end uses without thinner; 7 days at 72° F for
    tanks >= 250,000 gallons with Amercoat #8 thinner

Coatings - Tank
Amercoat 133[1] >= 50 gal. CLD 23 EPOXY
Amerlock 2[2] >= 40,000 gal. CLD 23 EPOXY
Amercoat 68HS[6] >= 5000 gal. CLD 23 EPOXY
Amercoat 68PW[6] >= 5,000 gal CLD 23 EPOXY
Novaguard 810[3] [4] CLD 23 EPOXY
Novaguard 810ER[3] [4] CLD 23 EPOXY
Novaguard 840[5] >= 3,000 gal. CLD 23 EPOXY 

[1] Colors: Oxide red, white
    Number of Coats: 1-2
    Maximum Field Use Dry Film Thickness (in mils): 6 per coat; 10 total
    Recoat Cure Time and Temperature: 24 hours at 75°F
    Final Cure and Temperature: 14 days at 75°F
    Special Comments: Mix ratio of resin to cure is 4:1 by volume. Mix for 5 minutes, let
    stand for 10 minutes, then remix for 2-3 minutes before application. Scrape the sides of
    the can while mixing.
[2] Colors: Ivory, White, Medium Gray, RT-1805 Blue, Oxide Red, Black
    Number of Coats: 2-4
    Sequence of Coats: Any combination of listed colors
    Maximum Field Use Dry Thickness: 8 mils per coat; 18 mils total
    Maximum Thinner: 12% Amercoat #8 by volume (optional use is limited to tanks >= 250,000
    gallons)
    Recoat Cure Time and Temperature: 24 hours at 72° F
    Final Cure Time/Temperature: 10 days at 72° F for all end uses except tank >= 250,000
    gallons which has a final cure of 7 days at 72° F
    Special Comments: Mix ratio of Base:Cure is 1:1 by volume or 1.1:1 by weight. Use of
    Amercoat #8 Thinner is limited to tanks of 250,000 gallons or greater.
    Final Cure Temp: 10 days at 72° F for all end uses without thinner; 7 days at 72° F for
    tanks >= 250,000 gallons with Amercoat #8 thinner
[3] Number of Coats: 1-2
    Maximum Field Use Dry Film Thickness (in mils): 30
    Recoat Cure Time and Temperature: 24 hours at 70°F
    Final Cure Time and Temperature: See Listing Note.
[4] Certified for tanks >= 500 gallons, pipe >=22", and valves >=2" with a final cure of 72
    hours @ 77º F and tanks >= 250,000 gallons and valves >= 3/4" with a final cure of 10
    days at 40º F.
[5] Colors: Cream, Green
    Number of Coats:  1-2
    Maximum field use dry film thickness (in mils): 30
    Recoat cure time and temperature: 24 hours at 70°F
    Final cure time and temperature: 72 hours at 70°F
    Special Comments: Mix ratio of base to hardener is 4:1 by volume
[6] Colors: Reddish Gray, Green 
    Number of coats: 1
    Sequence of coats: Primer
    Maximum field use dry film thickness: 4 mils
    Maximum thinner: 6% Amercoat 65
    Final Cure Time and temperature: 8 hours at 75°F
    Special comments: Mix ratio is 3.02:1.00:13.01 (Part A:PartB:Powder) by weight. Any
    certified PPG top coat may be used provided both primer and topcoat meet their
    individual Certified end uses.

Coatings - Valve
Amercoat 133[1] >= 4" CLD 23 EPOXY
Amerlock 2[2] >= 6" CLD 23 EPOXY
Amercoat 370[7] >= 4" CLD 23 EPOXY
Amerlock 400[8] >= 6" CLD 23 EPOXY
Novaguard 810[3] [4] CLD 23 EPOXY
Novaguard 810ER[3] [4] CLD 23 EPOXY
Novaguard 840[5] >= 4" CLD 23 EPOXY 

[1] Colors: Oxide red, white
    Number of Coats: 1-2
    Maximum Field Use Dry Film Thickness (in mils): 6 per coat; 10 total
    Recoat Cure Time and Temperature: 24 hours at 75°F
    Final Cure and Temperature: 14 days at 75°F
    Special Comments: Mix ratio of resin to cure is 4:1 by volume. Mix for 5 minutes, let
    stand for 10 minutes, then remix for 2-3 minutes before application. Scrape the sides of
    the can while mixing.
[2] Colors: Ivory, White, Medium Gray, RT-1805 Blue, Oxide Red, Black
    Number of Coats: 2-4
    Sequence of Coats: Any combination of listed colors
    Maximum Field Use Dry Thickness: 8 mils per coat; 18 mils total
    Maximum Thinner: 12% Amercoat #8 by volume (optional use is limited to tanks >= 250,000
    gallons)
    Recoat Cure Time and Temperature: 24 hours at 72° F
    Final Cure Time/Temperature: 10 days at 72° F for all end uses except tank >= 250,000
    gallons which has a final cure of 7 days at 72° F
    Special Comments: Mix ratio of Base:Cure is 1:1 by volume or 1.1:1 by weight. Use of
    Amercoat #8 Thinner is limited to tanks of 250,000 gallons or greater.
    Final Cure Temp: 10 days at 72° F for all end uses without thinner; 7 days at 72° F for
    tanks >= 250,000 gallons with Amercoat #8 thinner
[3] Number of Coats: 1-2
    Maximum Field Use Dry Film Thickness (in mils): 30
    Recoat Cure Time and Temperature: 24 hours at 70°F
    Final Cure Time and Temperature: See Listing Note.
[4] Certified for tanks >= 500 gallons, pipe >=22", and valves >=2" with a final cure of 72
    hours @ 77º F and tanks >= 250,000 gallons and valves >= 3/4" with a final cure of 10
    days at 40º F.
[5] Colors: Cream, Green
    Number of Coats:  1-2
    Maximum field use dry film thickness (in mils): 30
    Recoat cure time and temperature: 24 hours at 70°F
    Final cure time and temperature: 72 hours at 70°F
    Special Comments: Mix ratio of base to hardener is 4:1 by volume
[7] Colors: Black, light buff, oxide red, milliken blue, white
    Number of Coats: 2-4
    Maximum Field Use Dry Film Thickness (in mils): 24
    Maximum Thinner: 12.5% Amercoat #65 Thinner
    Recoat Cure Time and Temperature: 0.5 hours at 23°C
    Final Cure Time and Temperature: 7 days at 23°C
    Special Comments: Mix ratio of base:cure is 4:1 by volume.
[8] Colors: Ivory, medium gray, oxide red, RT-1805, white
    Number of Coats: 2-4
    Sequence of Coats: Any combination of Listed colors
    Maximum Field Use Dry Film Thickness (in mils): 6 per coat; 18 total
    Maximum Thinner: 12.5% Amercoat #65 by volume
    Recoat Cure Time and Temperature: 24 hours at 75°F
    Final Cure Time and Temperature: 7 days at 75°F
    Special Comments: Mix ratio of base:cure is 1:1 by volume.

Primers[9] [10]
Sigmaweld 199 US >= 900 gal. CLD 23 ZINC 

[9] This primer may be used with any Certified PPG topcoat provided both primer and topcoat
    meet their individual Certified end uses.
[10] Colors: Tan
     Number of Coats: 1
     Maximum Field Use Dry Film Thickness (in mils): 1 
     Maximum Thinner: None
     Recoat Cure Time and Temperature: Not Applicable
     Final Cure Time and Temperature: Primer (cure before application of topcoat) - 7 days at
     ambient temperature (20°C)
     Special Comments: Mix ratio of binder:paste is 2:1 by volume. Apply to steel substrate.

Number of matching Manufacturers is 1
Number of matching Products is 22
Processing time was 0 seconds