NSF Product and Service Listings
These NSF Official Listings are current as of Friday, December 26, 2025 at 12:15 a.m. Eastern Time. Please contact NSF to confirm the status of any Listing, report errors, or make suggestions.
Alert: NSF is concerned about fraudulent downloading and manipulation of website text. Always confirm this information by clicking on the below link for the most accurate information: http://info.nsf.org/Certified/PwsComponents/Listings.asp?Company=07180&Standard=061&
NSF/ANSI/CAN 61
Drinking Water System Components - Health Effects
Drinking Water System Components - Health Effects
NOTE: Unless otherwise indicated for Materials, Certification is only for the Water Contact Material shown in the Listing. Click here for a list of Abbreviations used in these Listings. Click here for the definitions of Water Contact Temperatures denoted in these Listings. Products certified to NSF/ANSI/CAN 61 comply with the health effects criteria in NSF/ANSI/CAN 600.
| Axalta Coating Systems, LLC | |
| 9800 Genard Road | |
| Houston, TX 77041 | |
| United States | |
| 800-247-3880 | |
| 832-955-0200 | |
| Visit this company's website |
Facility : Mt. Clemens, MI
Protective (Barrier) Materials
| Water | Water | |||
| Water Contact | Contact | Contact | ||
| Trade Designation | Size Restriction | Temp | Material | |
|
Coatings - Fittings |
||||
| AquaEC™ 2600[1] | 2" - 42" | CLD 23 | EPOXY | |
| AquaEC™ 2600EP[2] | 2" - 42" | CLD 23 | EPOXY | |
[1] Number of Coats: 1
Maximum Field Use Dry Film Thickness (in mils): 1
Maximum Thinner: none
Final Cure Time and Temperature: 10 minutes at 390°F
Special Comments: Mix ratio of Part A (resin feed):Part B (pigment feed) is 4.8:1 by
volume. Deionized water is added to the bath as needed to obtain 18–22% weight solids.
[2] Colors: Black
Number of Coats: 1
Maximum Field Use Dry Film Thickness (in mils): 1
Final Cure Time and Temperature: 10 minutes at 390ºF
Special Comments: Mix ratio of Part A:B is 4.8:1 by volume. Deionized water is added to
the bath as needed to obtain 18-22% weight solids.
|
||||
|
Coatings - Pipe |
||||
| AquaEC™ 6100 (1K: 4023-2161)[4] | >=1 1/2" | CLD 23 | EPOXY | |
| AquaEC™ 6100 (2K: EK-2160/629-2161)[3] | >=1 1/2" | CLD 23 | EPOXY | |
[3] Colors: Black - 2K version (2-part system)
Number of Coats: 1
Maximum Field Use Dry Thickness (in mils): 1.38 mils
Final Cure Time and Temperature: 10 min at 330°F
Special Comments: Mix ratio Part A:B = 5:1. Coating is diluted with deionized water to a
final solid content of 18-22% prior to application. Steel substrate is dipped into
coating and it is applied with a voltage (160-350 V). After a 2-3 minute dwell time the
painted component is cured for 10 minutes at 330°F.
[4] Colors: Black - 1K version (pre-blended)
Number of Coats: 1
Maximum Field Use Dry Thickness (in mils): 1.38 mils
Final Cure Time and Temperature: 10 min at 330°F
Special Comments: Coating is diluted with deionized water to a final solid content of
18-22% prior to application. Steel substrate is dipped into coating and is applied with
a voltage (160-350V). After a 2-3 minute dwell time the painted component is cured for
10 minutes at 330°F.
|
||||
|
Coatings - Valve |
||||
| AquaEC™ 2600[1] | 2" - 42" | CLD 23 | EPOXY | |
| AquaEC™ 2600EP[2] | 2" - 42" | CLD 23 | EPOXY | |
[1] Number of Coats: 1
Maximum Field Use Dry Film Thickness (in mils): 1
Maximum Thinner: none
Final Cure Time and Temperature: 10 minutes at 390°F
Special Comments: Mix ratio of Part A (resin feed):Part B (pigment feed) is 4.8:1 by
volume. Deionized water is added to the bath as needed to obtain 18–22% weight solids.
[2] Colors: Black
Number of Coats: 1
Maximum Field Use Dry Film Thickness (in mils): 1
Final Cure Time and Temperature: 10 minutes at 390ºF
Special Comments: Mix ratio of Part A:B is 4.8:1 by volume. Deionized water is added to
the bath as needed to obtain 18-22% weight solids.
|
||||
Facility : Houston, TX
Protective (Barrier) Materials
| Water | Water | |||
| Water Contact | Contact | Contact | ||
| Trade Designation | Size Restriction | Temp | Material | |
|
Coatings - Fittings |
||||
| 7-4527 GHEEN GREEN FBE[1] | >= 2" | D. HOT | PEC | |
| NAP-GARD FBE FBE PIPE POWDER 7-2500[1] | >= 2" | D. HOT | PEC | |
| NAP-GARD FBE FBE PIPE POWDER 7-2501[1] | >= 2" | D. HOT | PEC | |
| NAP-GARD FBE GREEN FAST PIPE POWDER 7-2508FG[1] | >= 2" | D. HOT | PEC | |
| NAP-GARD FBE GREEN LONG GEL FBE 7-2508LG[1] | >= 2" | D. HOT | PEC | |
| NAP-GARD FBE GREEN STD GEL PIPE POWDER 7-2508[1] | >= 2" | D. HOT | PEC | |
| Nap-Gard FBE Black Valve FBE 7-4510[2] | >= 2" | D. HOT | PEC | |
| Nap-Gard FBE Blue FBE 7-2540[3] | 8" - 48" | D. HOT | PEC | |
| Nap-Gard FBE GREEN FBE PIPE POWDER 7-2500V[1] | >=2” | D. HOT | PEC | |
| Nap-Gard FBE GREEN FBE PIPE POWDER 7-2500VFG[1] | >=2” | D. HOT | PEC | |
| Nap-Gard FBE GREEN FBE PIPE POWDER 7-2500VSG[1] | >=2” | D. HOT | PEC | |
| Nap-Gard FBE Multipurpose Green FBE 7-0014[4] | >= 1/2" | C. HOT | PEC | |
[1] Colors: Green, red
Number of Coats: 1
Maximum Field Use Dry Film Thickness (in mils): 14
Final Cure Time and Temperature: 60 seconds at 462°F
Special Comments: Preheat pipe to 464°F before powder application.
[2] Colors: Black
Number of Coats: 1
Maximum Field Use Dry Film Thickness (in mils): 60
Final Cure Time and Temperature: 3 - 10 minutes at 438 - 475°F
Special Comments: Preheat substrate to 400 - 500°F
[3] Number of Coats: 1
Maximum Field Use Dry Film Thickness (in mils): 14
Maximum Thinner: None
Final Cure Time and Temperature: 120 seconds at 226°C (438°F), 80 seconds at 232°C
(450°F), or 60 seconds at 239°C (463°F)
Special Comments: Preheat substrate to 239°C (463°F) before powder application.
[4] Colors: Green
Number of Coats: 1
Maximum Field Use Dry Film Thickness (in mils): 20
Maximum Thinner: None
Final Cure Time and Temperature: 20 minutes at 200°C or 13 minutes at 220°C
Special Comments: Preheat substrate to 425°F - 463°C before powder application.
|
||||
|
Coatings - Pipe |
||||
| 7-4527 GHEEN GREEN FBE[1] | >= 2" | D. HOT | PEC | |
| NAP-GARD FBE FBE PIPE POWDER 7-2500[1] | >= 2" | D. HOT | PEC | |
| NAP-GARD FBE FBE PIPE POWDER 7-2501[1] | >= 2" | D. HOT | PEC | |
| NAP-GARD FBE GREEN FAST PIPE POWDER 7-2508FG[1] | >= 2" | D. HOT | PEC | |
| NAP-GARD FBE GREEN LONG GEL FBE 7-2508LG[1] | >= 2" | D. HOT | PEC | |
| NAP-GARD FBE GREEN STD GEL PIPE POWDER 7-2508[1] | >= 2" | D. HOT | PEC | |
| Nap-Gard FBE Black Valve FBE 7-4510[2] | >= 2" | D. HOT | PEC | |
| Nap-Gard FBE Blue FBE 7-2540[3] | 8" - 48" | D. HOT | PEC | |
| Nap-Gard FBE GREEN FBE PIPE POWDER 7-2500V[1] | >=2” | D. HOT | PEC | |
| Nap-Gard FBE GREEN FBE PIPE POWDER 7-2500VFG[1] | >=2” | D. HOT | PEC | |
| Nap-Gard FBE GREEN FBE PIPE POWDER 7-2500VSG[1] | >=2” | D. HOT | PEC | |
| Nap-Gard FBE Multipurpose Green FBE 7-0014[4] | >= 1/2" | C. HOT | PEC | |
| Nap-Gard Tan FBE Tank 7-3500T[6] | >= 2" | D. HOT | PEC | |
| Nap-Gard White FBE Tank Coating 7-3500[6] | >= 2" | D. HOT | PEC | |
| TANK TAN EFT-602-P7[6] | >= 2" | D. HOT | PEC | |
[1] Colors: Green, red
Number of Coats: 1
Maximum Field Use Dry Film Thickness (in mils): 14
Final Cure Time and Temperature: 60 seconds at 462°F
Special Comments: Preheat pipe to 464°F before powder application.
[2] Colors: Black
Number of Coats: 1
Maximum Field Use Dry Film Thickness (in mils): 60
Final Cure Time and Temperature: 3 - 10 minutes at 438 - 475°F
Special Comments: Preheat substrate to 400 - 500°F
[3] Number of Coats: 1
Maximum Field Use Dry Film Thickness (in mils): 14
Maximum Thinner: None
Final Cure Time and Temperature: 120 seconds at 226°C (438°F), 80 seconds at 232°C
(450°F), or 60 seconds at 239°C (463°F)
Special Comments: Preheat substrate to 239°C (463°F) before powder application.
[4] Colors: Green
Number of Coats: 1
Maximum Field Use Dry Film Thickness (in mils): 20
Maximum Thinner: None
Final Cure Time and Temperature: 20 minutes at 200°C or 13 minutes at 220°C
Special Comments: Preheat substrate to 425°F - 463°C before powder application.
[6] Colors: Tan, White
Number of Coats: 1
Maximum Field Use Dry Film Thickness (in mils): 10
Final Cure Time: 10 minutes at 400°F
Special Comments: Preheat part to 462°F before powder application.
|
||||
|
Coatings - Pump |
||||
| Nap-Gard FBE Black Valve FBE 7-4510[2] | >= 2" | D. HOT | PEC | |
[2] Colors: Black
Number of Coats: 1
Maximum Field Use Dry Film Thickness (in mils): 60
Final Cure Time and Temperature: 3 - 10 minutes at 438 - 475°F
Special Comments: Preheat substrate to 400 - 500°F
|
||||
|
Coatings - Tank |
||||
| 7-4527 GHEEN GREEN FBE[1] | >= 5 gal. | D. HOT | PEC | |
| NAP-GARD FBE FBE PIPE POWDER 7-2500[1] | >= 5 gal. | D. HOT | PEC | |
| NAP-GARD FBE FBE PIPE POWDER 7-2501[1] | >= 5 gal. | D. HOT | PEC | |
| NAP-GARD FBE GREEN FAST PIPE POWDER 7-2508FG[1] | >= 5 gal. | D. HOT | PEC | |
| NAP-GARD FBE GREEN LONG GEL FBE 7-2508LG[1] | >= 5 gal. | D. HOT | PEC | |
| NAP-GARD FBE GREEN STD GEL PIPE POWDER 7-2508[1] | >= 5 gal. | D. HOT | PEC | |
| Nap-Gard FBE Black Valve FBE 7-4510[2] | >= 5 gal. | D. HOT | PEC | |
| Nap-Gard FBE GREEN FBE PIPE POWDER 7-2500V[1] | >=5 gal. | D. HOT | PEC | |
| Nap-Gard FBE GREEN FBE PIPE POWDER 7-2500VFG[1] | >=5 gal. | D. HOT | PEC | |
| Nap-Gard FBE GREEN FBE PIPE POWDER 7-2500VSG[1] | >=5 gal. | D. HOT | PEC | |
| Nap-Gard FBE Multipurpose Green FBE 7-0014[4] | >= 5 gal. | C. HOT | PEC | |
| Nap-Gard Tan FBE Tank 7-3500T[6] | >= 5 gal. | D. HOT | PEC | |
| Nap-Gard White FBE Tank Coating 7-3500[6] | >= 5 gal . | D. HOT | PEC | |
| Tank Tan EFT-602-P7[6] | >= 5 gal. | D. HOT | PEC | |
[1] Colors: Green, red
Number of Coats: 1
Maximum Field Use Dry Film Thickness (in mils): 14
Final Cure Time and Temperature: 60 seconds at 462°F
Special Comments: Preheat pipe to 464°F before powder application.
[2] Colors: Black
Number of Coats: 1
Maximum Field Use Dry Film Thickness (in mils): 60
Final Cure Time and Temperature: 3 - 10 minutes at 438 - 475°F
Special Comments: Preheat substrate to 400 - 500°F
[4] Colors: Green
Number of Coats: 1
Maximum Field Use Dry Film Thickness (in mils): 20
Maximum Thinner: None
Final Cure Time and Temperature: 20 minutes at 200°C or 13 minutes at 220°C
Special Comments: Preheat substrate to 425°F - 463°C before powder application.
[6] Colors: Tan, White
Number of Coats: 1
Maximum Field Use Dry Film Thickness (in mils): 10
Final Cure Time: 10 minutes at 400°F
Special Comments: Preheat part to 462°F before powder application.
|
||||
|
Coatings - Valve |
||||
| 7-4527 GHEEN GREEN FBE[1] | >= 2" | D. HOT | PEC | |
| NAP-GARD FBE FBE PIPE POWDER 7-2500[1] | >= 2" | D. HOT | PEC | |
| NAP-GARD FBE FBE PIPE POWDER 7-2501[1] | >= 2" | D. HOT | PEC | |
| NAP-GARD FBE GREEN FAST PIPE POWDER 7-2508FG[1] | >= 2" | D. HOT | PEC | |
| NAP-GARD FBE GREEN LONG GEL FBE 7-2508LG[1] | >= 2 | D. HOT | PEC | |
| NAP-GARD FBE GREEN STD GEL PIPE POWDER 7-2508[1] | >= 2" | D. HOT | PEC | |
| Nap-Gard FBE Black Valve FBE 7-4510[2] | >= 2" | D. HOT | PEC | |
| Nap-Gard FBE Blue FBE 7-2540[3] | 8" - 48" | D. HOT | PEC | |
| Nap-Gard FBE CV Red FBE 7-4500[7] | 4" - 36" | C. HOT | PEC | |
| Nap-Gard FBE GREEN FBE PIPE POWDER 7-2500V[1] | >=2” | D. HOT | PEC | |
| Nap-Gard FBE GREEN FBE PIPE POWDER 7-2500VFG[1] | >=2” | D. HOT | PEC | |
| Nap-Gard FBE GREEN FBE PIPE POWDER 7-2500VSG[1] | >=2” | D. HOT | PEC | |
| Nap-Gard FBE Multipurpose Green FBE 7-0014[4] | >= 1" | C. HOT | PEC | |
[1] Colors: Green, red
Number of Coats: 1
Maximum Field Use Dry Film Thickness (in mils): 14
Final Cure Time and Temperature: 60 seconds at 462°F
Special Comments: Preheat pipe to 464°F before powder application.
[2] Colors: Black
Number of Coats: 1
Maximum Field Use Dry Film Thickness (in mils): 60
Final Cure Time and Temperature: 3 - 10 minutes at 438 - 475°F
Special Comments: Preheat substrate to 400 - 500°F
[3] Number of Coats: 1
Maximum Field Use Dry Film Thickness (in mils): 14
Maximum Thinner: None
Final Cure Time and Temperature: 120 seconds at 226°C (438°F), 80 seconds at 232°C
(450°F), or 60 seconds at 239°C (463°F)
Special Comments: Preheat substrate to 239°C (463°F) before powder application.
[4] Colors: Green
Number of Coats: 1
Maximum Field Use Dry Film Thickness (in mils): 20
Maximum Thinner: None
Final Cure Time and Temperature: 20 minutes at 200°C or 13 minutes at 220°C
Special Comments: Preheat substrate to 425°F - 463°C before powder application.
[7] Number of Coats: 1
Maximum Field Use Dry Film Thickness (in mils): 30
Final Cure Time and Temperature: Post-heat temperature and minimum cure times: 300°F for
15 minutes, 325°F for 9 minutes, 350° for 7 minutes, 375° for 6 minutes, 400°F for 5
minutes
Special Comments: Preheat substrate to a minimum of 275°F
|
||||
NOTE: Only products bearing the NSF Mark on the product, product packaging, and/or
documentation shipped with the product are Certified.
Number of matching Manufacturers is 1
Number of matching Products is 61
Processing time was 0 seconds
