NSF Product and Service Listings
These NSF Official Listings are current as of Sunday, June 7, 2026 at 12:15 a.m. Eastern Time. Please contact NSF to confirm the status of any Listing, report errors, or make suggestions.
Alert: NSF is concerned about fraudulent downloading and manipulation of website text. Always confirm this information by clicking on the below link for the most accurate information: http://info.nsf.org/Certified/PwsComponents/Listings.asp?Company=08420&Standard=061&
NSF/ANSI/CAN 61
Drinking Water System Components - Health Effects
Drinking Water System Components - Health Effects
NOTE: Unless otherwise indicated for Materials, Certification is only for the Water Contact Material shown in the Listing. Click here for a list of Abbreviations used in these Listings. Click here for the definitions of Water Contact Temperatures denoted in these Listings. Products certified to NSF/ANSI/CAN 61 comply with the health effects criteria in NSF/ANSI/CAN 600.
| Akzo Nobel Coatings, Inc. | |
| Flying Hills Corporate Center | |
| 3 Commerce Drive | |
| Reading, PA 19607 | |
| United States | |
| 610-775-6600 |
Facility : Reading, PA
Protective (Barrier) Materials
| Water | Water | |||
| Water Contact | Contact | Contact | ||
| Trade Designation | Size Restriction | Temp | Material | |
|
Coatings - Fittings |
||||
| AA119QF INTERPON 100 10-1160 JERSEY CREAM[1] | >= 2" | CLD 23 | PEC | |
| AM106QF INTERPON 100 10-4081 RED BROWN[2] | >= 2" | CLD 23 | PEC | |
| HAF06QF RESICOAT R4-ES 10-1161 WHITE[3] | >= 2" | CLD 23 | PEC | |
| HGC24QF Resicoat R8-FB Red-Brown[4] | >= 1" | D. HOT | PEC | |
| HGF6AQF Resicoat R8-ES Red-Brown[4] | >= 1" | D. HOT | PEC | |
| HJC36R QF Resicoat R4-FB Blue[1] [5] [6] | >=1" | D. HOT | PEC | |
| HJF10R Resicoat R4-ES RAL5017 Blue[1] [5] [7] | >=1" | D. HOT | PEC | |
| HJF4NQF Resicoat R8-ES Blue[8] | >= 1" | D. HOT | PEC | |
| HNF12QF RESICOAT R4-ES 10-7314 BLACK[9] | >= 1/2" | CLD 23 | PEC | |
| HNF13QF RESICOAT PI 76-7001 BLACK[5] | >= 1" | D. HOT | NP | |
[1] Number of Coats: 1
Maximum Field Use Dry Film Thickness (in mils): 20
Final Cure Time and Temperature: 15 minutes at 350°F
Special Comments: Preheat substrate to 350° F.
[2] Number of Coats: 1
Maximum Field Use Dry Film Thickness (in mils): 16
Special Comments: Preheat part before powder application to 350°F for 20 minutes. Post
heat to 350°F for 15 minutes.
[3] Number of Coats: 1
Maximum Field Use Dry Film Thickness (in mils): 15
Maximum Thinner: None
Final Cure Time and Temperature: 20 minutes at 350°F
Special Comments: Preheat substrate to 350°F
[4] Colors: Red-Brown
Number of Coats: 1
Maximum field use dry film thickness (in mils): 14
Final cure time and temperature: 20 minutes at 200°C
Special Comments: Preheat substrate to 200°C - 220°C (HGF6AQF), Preheat substrate to
190°C - 210°C (HGC24QF)
[5] Number of Coats: 1
Maximum Field Use Dry Film Thickness (in mils): 18
Final Cure Time and Temperature:: 1 minute at 475ºF
Special Comments: Preheat panel to 650ºF before coating
[6] Colors: Blue
Number of Coats: 1
Maximum field use dry film thickness (in mils): 20
Final Cure Time/Temp: See special comments
Special Comments: Pre-heat parts to 190-210°C. The coating is considered self-curing if
the wall thickness
of the part is greater than 8 mm (the coating will be cured by the time the part reaches
ambient temp). If
the preheated part is less than 8 mm, the part will require a post-cure of 3-8 min at
190-210°C (374°F).
[7] Colors: Blue
Number of Coats: 1
Maximum field use dry film thickness (in mils): 20
Final cure time and temperature: 20 minutes at 428°F
[8] Colors: Blue
Number of Coats: 1
Maximum field use dry film thickness (in mils): 14
Final cure time and temperature: 20 minutes at 200°C
Special Comments: Preheat substrate to 200°C - 220°C
[9] Number of Coats: 1
Maximum Field Use Dry Film Thickness (in mils): 16
Special Comments: Preheat part before powder application to 350°F for 20 minutes. Post
heat part to 350°F for 20 minutes.
|
||||
|
Coatings - Pipe |
||||
| AA119QF INTERPON 100 10-1160 JERSEY CREAM[1] | >= 2" | CLD 23 | PEC | |
| AM106QF INTERPON 100 10-4081 RED BROWN[2] | >= 2" | CLD 23 | PEC | |
| HAF06QF RESICOAT R4-ES 10-1161 WHITE[3] | >= 2" | CLD 23 | PEC | |
| HGG00QF Resicoat R4-ES Red Oxide[10] | >= 6" | CLD 23 | PEC | |
| HNF12QF RESICOAT R4-ES 10-7314 BLACK[9] | >= 1/2" | CLD 23 | PEC | |
| HNF13QF RESICOAT PI 76-7001 BLACK[5] | >= 18" | D. HOT | NP | |
[1] Number of Coats: 1
Maximum Field Use Dry Film Thickness (in mils): 20
Final Cure Time and Temperature: 15 minutes at 350°F
Special Comments: Preheat substrate to 350° F.
[2] Number of Coats: 1
Maximum Field Use Dry Film Thickness (in mils): 16
Special Comments: Preheat part before powder application to 350°F for 20 minutes. Post
heat to 350°F for 15 minutes.
[3] Number of Coats: 1
Maximum Field Use Dry Film Thickness (in mils): 15
Maximum Thinner: None
Final Cure Time and Temperature: 20 minutes at 350°F
Special Comments: Preheat substrate to 350°F
[5] Number of Coats: 1
Maximum Field Use Dry Film Thickness (in mils): 18
Final Cure Time and Temperature:: 1 minute at 475ºF
Special Comments: Preheat panel to 650ºF before coating
[9] Number of Coats: 1
Maximum Field Use Dry Film Thickness (in mils): 16
Special Comments: Preheat part before powder application to 350°F for 20 minutes. Post
heat part to 350°F for 20 minutes.
[10] Colors: Red
Number of Coats: 1
Maximum field use dry film thickness (in mils): 10
Final cure time and temperature: 15 minutes at 350° F
|
||||
|
Coatings - Tank |
||||
| AA119QF INTERPON 100 10-1160 JERSEY CREAM[1] | >= 5 gal. | CLD 23 | PEC | |
| AM106QF INTERPON 100 10-4081 RED BROWN[2] | >= 5 gal. | CLD 23 | PEC | |
| HAF06QF RESICOAT R4-ES 10-1161 WHITE[3] | >= 5 gal. | CLD 23 | PEC | |
| HGG00QF Resicoat R4-ES Red Oxide[10] | >= 4,000 gal. | CLD 23 | PEC | |
| HLF93QF RESICOAT R4-ES 10-7208 GRAY[2] | >= 5 gal. | CLD 23 | PEC | |
| HNF12QF RESICOAT R4-ES 10-7314 BLACK[9] | >= 5 gal. | CLD 23 | PEC | |
| HNF13QF RESICOAT PI 76-7001 BLACK[5] | >= 300 gal. | D. HOT | NP | |
[1] Number of Coats: 1
Maximum Field Use Dry Film Thickness (in mils): 20
Final Cure Time and Temperature: 15 minutes at 350°F
Special Comments: Preheat substrate to 350° F.
[2] Number of Coats: 1
Maximum Field Use Dry Film Thickness (in mils): 16
Special Comments: Preheat part before powder application to 350°F for 20 minutes. Post
heat to 350°F for 15 minutes.
[3] Number of Coats: 1
Maximum Field Use Dry Film Thickness (in mils): 15
Maximum Thinner: None
Final Cure Time and Temperature: 20 minutes at 350°F
Special Comments: Preheat substrate to 350°F
[5] Number of Coats: 1
Maximum Field Use Dry Film Thickness (in mils): 18
Final Cure Time and Temperature:: 1 minute at 475ºF
Special Comments: Preheat panel to 650ºF before coating
[9] Number of Coats: 1
Maximum Field Use Dry Film Thickness (in mils): 16
Special Comments: Preheat part before powder application to 350°F for 20 minutes. Post
heat part to 350°F for 20 minutes.
[10] Colors: Red
Number of Coats: 1
Maximum field use dry film thickness (in mils): 10
Final cure time and temperature: 15 minutes at 350° F
|
||||
|
Coatings - Valve |
||||
| AA119QF INTERPON 100 10-1160 JERSEY CREAM[1] | >= 2" | CLD 23 | PEC | |
| HAF06QF RESICOAT R4-ES 10-1161 WHITE[3] | >= 2" | CLD 23 | PEC | |
| HGC24QF Resicoat R8-FB Red-Brown[4] | >= 1" | D. HOT | PEC | |
| HGF6AQF Resicoat R8-ES Red-Brown[4] | >= 1" | D. HOT | PEC | |
| HJC36R QF Resicoat R4-FB Blue[1] [5] [6] | >=1" | D. HOT | PEC | |
| HJF10R Resicoat R4-ES RAL5017 Blue[1] [5] [7] | >=1" | D. HOT | PEC | |
| HJF4NQF Resicoat R8-ES Blue[8] | >= 1" | D. HOT | PEC | |
| HNF12QF RESICOAT R4-ES 10-7314 BLACK[9] | >= 1/2" | CLD 23 | PEC | |
| HNF13QF RESICOAT PI 76-7001 BLACK[5] | >= 4" | D. HOT | NP | |
[1] Number of Coats: 1
Maximum Field Use Dry Film Thickness (in mils): 20
Final Cure Time and Temperature: 15 minutes at 350°F
Special Comments: Preheat substrate to 350° F.
[3] Number of Coats: 1
Maximum Field Use Dry Film Thickness (in mils): 15
Maximum Thinner: None
Final Cure Time and Temperature: 20 minutes at 350°F
Special Comments: Preheat substrate to 350°F
[4] Colors: Red-Brown
Number of Coats: 1
Maximum field use dry film thickness (in mils): 14
Final cure time and temperature: 20 minutes at 200°C
Special Comments: Preheat substrate to 200°C - 220°C (HGF6AQF), Preheat substrate to
190°C - 210°C (HGC24QF)
[5] Number of Coats: 1
Maximum Field Use Dry Film Thickness (in mils): 18
Final Cure Time and Temperature:: 1 minute at 475ºF
Special Comments: Preheat panel to 650ºF before coating
[6] Colors: Blue
Number of Coats: 1
Maximum field use dry film thickness (in mils): 20
Final Cure Time/Temp: See special comments
Special Comments: Pre-heat parts to 190-210°C. The coating is considered self-curing if
the wall thickness
of the part is greater than 8 mm (the coating will be cured by the time the part reaches
ambient temp). If
the preheated part is less than 8 mm, the part will require a post-cure of 3-8 min at
190-210°C (374°F).
[7] Colors: Blue
Number of Coats: 1
Maximum field use dry film thickness (in mils): 20
Final cure time and temperature: 20 minutes at 428°F
[8] Colors: Blue
Number of Coats: 1
Maximum field use dry film thickness (in mils): 14
Final cure time and temperature: 20 minutes at 200°C
Special Comments: Preheat substrate to 200°C - 220°C
[9] Number of Coats: 1
Maximum Field Use Dry Film Thickness (in mils): 16
Special Comments: Preheat part before powder application to 350°F for 20 minutes. Post
heat part to 350°F for 20 minutes.
|
||||
Number of matching Manufacturers is 1
Number of matching Products is 32
Processing time was 0 seconds
