NSF Product and Service Listings
These NSF Official Listings are current as of Friday, December 26, 2025 at 12:15 a.m. Eastern Time. Please contact NSF to confirm the status of any Listing, report errors, or make suggestions.
Alert: NSF is concerned about fraudulent downloading and manipulation of website text. Always confirm this information by clicking on the below link for the most accurate information: http://info.nsf.org/Certified/PwsComponents/Listings.asp?Company=15490&Standard=061&
NSF/ANSI/CAN 61
Drinking Water System Components - Health Effects
Drinking Water System Components - Health Effects
NOTE: Unless otherwise indicated for Materials, Certification is only for the Water Contact Material shown in the Listing. Click here for a list of Abbreviations used in these Listings. Click here for the definitions of Water Contact Temperatures denoted in these Listings. Products certified to NSF/ANSI/CAN 61 comply with the health effects criteria in NSF/ANSI/CAN 600.
| Akzo Nobel Coatings Inc. | |
| P.O. Box 91629 | |
| Cleveland, OH 44101 | |
| United States | |
| 216-750-6475 |
Facility : Warsaw, IN
Protective (Barrier) Materials
| Water | Water | |||
| Water Contact | Contact | Contact | ||
| Trade Designation | Size Restriction | Temp | Material | |
|
Coatings - Pipe[1] |
||||
| HA000Q INT 100 White Primer | >= 6" | CLD 23 | PEC | |
| HL001QF Interpon 100 Duracoat Grey | >= 6" | CLD 23 | PEC | |
| HM001QF INT100 16452 Tarsco Tan | >= 6" | CLD 23 | PEC | |
[1] Number of Coats: 1-2
Maximum Field Use Dry Film Thickness (in mils): 10
Final Cure Time and Temperature: 15 minutes at 350°F
|
||||
|
Coatings - Tank[1] |
||||
| HA000Q INT 100 White Primer | >= 4000 gal. | CLD 23 | PEC | |
| HL001QF Interpon 100 Duracoat Grey | >= 4000 gal. | CLD 23 | PEC | |
| HM001QF INT100 16452 Tarsco Tan | >= 4000 gal. | CLD 23 | PEC | |
[1] Number of Coats: 1-2
Maximum Field Use Dry Film Thickness (in mils): 10
Final Cure Time and Temperature: 15 minutes at 350°F
|
||||
Facility : Nashville, TN
Protective (Barrier) Materials
| Water | Water | |||
| Water Contact | Contact | Contact | ||
| Trade Designation | Size Restriction | Temp | Material | |
|
Coatings - Fittings |
||||
| HAF09R Resicoat R4-ES White[1] | >= 1" | D. HOT | PEC | |
| HEF22R Resicoat R4-ES Yellow[1] | >= 1" | D. HOT | PEC | |
| HGC17R Resicoat R4-FB Red[2] | >= 1" | D. HOT | PEC | |
| HGF17R Resicoat R4-ES Rust[3] | >= 1" | D. HOT | PEC | |
| HJ606R Resicoat R4-ES Blue[1] | >= 1" | D. HOT | PEC | |
| HJC08R Resicoat R4-FB Blue[4] | >= 1" | D. HOT | PEC | |
| HJC36R QF Resicoat R4-FB Blue[5] | >= 1" | D. HOT | PEC | |
| HJF10R Resicoat R4-ES RAL5017 Blue[1] | >= 1" | D. HOT | PEC | |
| HJF14R Resicoat R4-ES RAL5015 Blue[1] | >= 1" | D. HOT | PEC | |
| HJF24R Resicoat R4-ES Blue[6] | >= 1" | D. HOT | PEC | |
| HJF42R Resicoat R4-ES Blue[1] | >= 1" | D. HOT | PEC | |
| HJF4BR Resicoat R4-ES Blue[1] | >= 1" | D. HOT | PEC | |
| HJF99R Resicoat R4-ES RAL5009 Blue[1] | >= 1" | D. HOT | PEC | |
| HKF47R Resicoat R4-ES Green[7] | >= 1" | D. HOT | PEC | |
| HNF24R Resicoat R4-ES Black[3] | >= 1" | D. HOT | PEC | |
| Resicoat R4-ES HGF38R[8] | >= 1" | D. HOT | PEC | |
[1] Colors: Blue, white, yellow
Number of Coats: 1
Maximum Field Use Dry Film Thickness (in mils): 20
Maximum Thinner: None
Final Cure: 20 minutes at 428°F
[2] Colors: Red
Number of Coats: 1
Maximum Field Use Dry Film Thickness (in mils): 20
Final Cure Time and Temperature: 20 minutes at 220°C
Special Comments: Preheat at 200°C - 230°C
[3] Colors: Black, rust
Number of Coats: 1
Maximum Field Use Dry Film Thickness (in mils): 20
Final Cure Time and Temperature: 20 minutes at 428°F
[4] Colors: Blue
Number of Coats: 1
Maximum Field Use Dry Film Thickness (in mils): 20
Recoat Cure Time and Temperature: 20 minutes at 220°C
Special Comments: Pre-heat at 200°C - 230°C
[5] Colors: Blue
Number of Coats: 1
Maximum field use dry film thickness (in mils): 20
Final cure time and temperature: See special comments
Special comments: Pre-heat parts to 190-210°C. The coating is considered self-curing if
the wall thickness of the part is
greater than 8 mm (the coating will be cured by the time the part reaches ambient temp).
If the preheated part is less than
8 mm, the part will require a post-cure of 3-8 min at 190-210°C (374°F).
[6] Number of Coats: 1
Maximum Field Use Dry Film Thickness (in mils): 20
Final Cure Time and Temperature: 20 minutes at 428°F
Special Comments: Self curing on 8 mm or heavier steel at 392°F - 428°F metal
temperature.
[7] Number of Coats: 1
Maximum Field Use Dry Film Thickness (in mils): 35
Final Cure Time and Temperature: 455°F metal temperature and post cured for 10 minutes
at 455°F
Special Comments: Metal plates are pre-heated to 455°F and sprayed while hot. Plates
are then post cured for 10 minutes at 455°F.
[8] Colors: Red brown
Number of Coats: 1
Maximum Field Use Dry Film Thickness (in mils): 20
Maximum Thinner: None
Final Cure Time and Temperature: 20 minutes at 428ºF
|
||||
|
Coatings - Pipe |
||||
| AD139QF Interpon 100 Tank Tan[9] | >= 6" | CLD 23 | PEC | |
| HA000Q Interpon 100 White Primer[10] | >= 1/2" | CLD 23 | PEC | |
| HKF47R Resicoat R4-ES Green[7] | >= 1/2" | D. HOT | PEC | |
| HL001QF Interpon 100 Duracoat Grey[10] | >= 1/2" | CLD 23 | PEC | |
[7] Number of Coats: 1
Maximum Field Use Dry Film Thickness (in mils): 35
Final Cure Time and Temperature: 455°F metal temperature and post cured for 10 minutes
at 455°F
Special Comments: Metal plates are pre-heated to 455°F and sprayed while hot. Plates
are then post cured for 10 minutes at 455°F.
[9] Number of Coats: 1
Maximum Field Use Dry Thickness: 10 mils
Final Cure Time/Temperature: 10 minutes at 400°F
[10] Colors: White, Grey
Number of Coats: 1
Maximum field use dry film thickness (in mils): 10
Final cure time and temperature: 15 minutes at 350° F
|
||||
|
Coatings - Tank |
||||
| AD139QF Interpon 100 Tank Tan[9] | >= 4000 gal. | CLD 23 | PEC | |
| HA000Q Interpon 100 White Primer[10] | >= 4000 gal. | CLD 23 | PEC | |
| HL001QF Interpon 100 Duracoat Grey[10] | >= 4000 gal. | CLD 23 | PEC | |
[9] Number of Coats: 1
Maximum Field Use Dry Thickness: 10 mils
Final Cure Time/Temperature: 10 minutes at 400°F
[10] Colors: White, Grey
Number of Coats: 1
Maximum field use dry film thickness (in mils): 10
Final cure time and temperature: 15 minutes at 350° F
|
||||
|
Coatings - Valve |
||||
| HAF09R Resicoat R4-ES White[1] | >= 1" | D. HOT | PEC | |
| HEF22R Resicoat R4-ES Yellow[1] | >= 1" | D. HOT | PEC | |
| HGC17R Resicoat R4-FB Red[2] | >= 1" | D. HOT | PEC | |
| HGF17R Resicoat R4-ES Rust[3] | >= 1" | D. HOT | PEC | |
| HJ606R Resicoat R4-ES Blue[1] | >= 1" | D. HOT | PEC | |
| HJC08R Resicoat R4-FB Blue[4] | >= 1" | D. HOT | PEC | |
| HJC36R QF Resicoat R4-FB Blue[5] | >= 1" | D. HOT | PEC | |
| HJF10R Resicoat R4-ES RAL5017 Blue[1] | >= 1" | D. HOT | PEC | |
| HJF14R Resicoat R4-ES RAL5015 Blue[1] | >= 1" | D. HOT | PEC | |
| HJF24R Resicoat R4-ES Blue[6] | >= 1" | D. HOT | PEC | |
| HJF42R Resicoat R4-ES Blue[1] | >= 1" | D. HOT | PEC | |
| HJF4BR Resicoat R4-ES Blue[1] | >= 1" | D. HOT | PEC | |
| HJF99R Resicoat R4-ES RAL5009 Blue[1] | >= 1" | D. HOT | PEC | |
| HKF47R Resicoat R4-ES Green[7] | >= 1" | D. HOT | PEC | |
| HNF24R Resicoat R4-ES Black[3] | >= 1" | D. HOT | PEC | |
| Resicoat R4-ES HGF38R[8] | >= 1" | D. HOT | PEC | |
[1] Colors: Blue, white, yellow
Number of Coats: 1
Maximum Field Use Dry Film Thickness (in mils): 20
Maximum Thinner: None
Final Cure: 20 minutes at 428°F
[2] Colors: Red
Number of Coats: 1
Maximum Field Use Dry Film Thickness (in mils): 20
Final Cure Time and Temperature: 20 minutes at 220°C
Special Comments: Preheat at 200°C - 230°C
[3] Colors: Black, rust
Number of Coats: 1
Maximum Field Use Dry Film Thickness (in mils): 20
Final Cure Time and Temperature: 20 minutes at 428°F
[4] Colors: Blue
Number of Coats: 1
Maximum Field Use Dry Film Thickness (in mils): 20
Recoat Cure Time and Temperature: 20 minutes at 220°C
Special Comments: Pre-heat at 200°C - 230°C
[5] Colors: Blue
Number of Coats: 1
Maximum field use dry film thickness (in mils): 20
Final cure time and temperature: See special comments
Special comments: Pre-heat parts to 190-210°C. The coating is considered self-curing if
the wall thickness of the part is
greater than 8 mm (the coating will be cured by the time the part reaches ambient temp).
If the preheated part is less than
8 mm, the part will require a post-cure of 3-8 min at 190-210°C (374°F).
[6] Number of Coats: 1
Maximum Field Use Dry Film Thickness (in mils): 20
Final Cure Time and Temperature: 20 minutes at 428°F
Special Comments: Self curing on 8 mm or heavier steel at 392°F - 428°F metal
temperature.
[7] Number of Coats: 1
Maximum Field Use Dry Film Thickness (in mils): 35
Final Cure Time and Temperature: 455°F metal temperature and post cured for 10 minutes
at 455°F
Special Comments: Metal plates are pre-heated to 455°F and sprayed while hot. Plates
are then post cured for 10 minutes at 455°F.
[8] Colors: Red brown
Number of Coats: 1
Maximum Field Use Dry Film Thickness (in mils): 20
Maximum Thinner: None
Final Cure Time and Temperature: 20 minutes at 428ºF
|
||||
Number of matching Manufacturers is 1
Number of matching Products is 45
Processing time was 0 seconds
