NSF Product and Service Listings

These NSF Official Listings are current as of Saturday, December 13, 2025 at 12:15 a.m. Eastern Time. Please contact NSF to confirm the status of any Listing, report errors, or make suggestions.

Alert: NSF is concerned about fraudulent downloading and manipulation of website text. Always confirm this information by clicking on the below link for the most accurate information: http://info.nsf.org/Certified/PwsComponents/Listings.asp?Company=2W800&Standard=061&


NSF/ANSI/CAN 61
Drinking Water System Components - Health Effects

NOTE: Unless otherwise indicated for Materials, Certification is only for the Water Contact Material shown in the Listing. Click here for a list of Abbreviations used in these Listings. Click here for the definitions of Water Contact Temperatures denoted in these Listings. Products certified to NSF/ANSI/CAN 61 comply with the health effects criteria in NSF/ANSI/CAN 600.

 
PPG Coatings Europe B.V. 
P.O. Box 58034
1040 HA Amsterdam 
The Netherlands 
31 20 407 5050
Visit this company's website


Facility : Deurne, Belgium

Protective (Barrier) Materials

    Water Water
  Water Contact Contact Contact
Trade Designation Size Restriction Temp Material

Coatings - Pipe[1]
Sigmaguard CSF 585[2] >= 20 cm CLD 23 EPOXY 

[1] Only products bearing the NSF Mark on the product, product packaging, and/or
    documentation shipped with the product are Certified.
[2] Colors: Blue 1000, White 7000
    Number of Coats: 1
    Maximum Field Use Dry Film Thickness (in mils): 16
    Maximum Thinner: None
    Final Cure: 12 days @ 20°C
    Special Comments: Mix ratio of A:B is 83:17 by weight. Mix for 5 minutes, 
                      let stand for 10 minutes, then remix for 1 minute before 
                      application. Scrape the sides of the can while mixing.

Coatings - Tank[1]
Sigmaguard CSF 585[2] >= 100 gal. CLD 23 EPOXY
Sigmaguard CSF 650[3] >= 2000 gal. CLD 23 EPOXY 

[1] Only products bearing the NSF Mark on the product, product packaging, and/or
    documentation shipped with the product are Certified.
[2] Colors: Blue 1000, White 7000
    Number of Coats: 1
    Maximum Field Use Dry Film Thickness (in mils): 16
    Maximum Thinner: None
    Final Cure: 12 days @ 20°C
    Special Comments: Mix ratio of A:B is 83:17 by weight. Mix for 5 minutes, 
                      let stand for 10 minutes, then remix for 1 minute before 
                      application. Scrape the sides of the can while mixing.
[3] Colors: Green
    Number of Coats: 1
    Maximum Field Use Dry Film Thickness (in mils): 16
    Maximum Thinner: None
    Final Cure: 5 days @ 20°C
    Special Comments: Mix ratio of base:hardener is 4:1 by volume. Once cure is complete,
    fill tank with fresh water and allow to soak for 4 days. Then rinse with high pressure
    water and drain tank.



Facility : Estado de Mexico, Mexico

Protective (Barrier) Materials

    Water Water
  Water Contact Contact Contact
Trade Designation Size Restriction Temp Material

Coatings - Pipe[1] [2]
Sigmaline 855 (11) Blue >= 20" CLD 23 PUR
Sigmaline 855 (11) Off-White >= 20" CLD 23 PUR 

[1] Only products bearing the NSF Mark on the product, product packaging, and/or
    documentation shipped with the product are Certified.
    
[2] Colors: Blue, Off-White
    Number of Coats: 1
    Maximum Field Use Dry Film Thickness (in mils): 60
    Maximum Thinner: None
    Final Cure: 72 hours @ 20°C
    Special Comments: Mix ratio of Part A:B = 1:1 by volume



Facility : Nam-gu, Korea, Republic of

Protective (Barrier) Materials

    Water Water
  Water Contact Contact Contact
Trade Designation Size Restriction Temp Material

Coatings - Pipe[1]
SigmaGuard CSF 650[2] >= 500 mm CLD 23 EPOXY 

[1] Only products bearing the NSF Mark on the product, product packaging, and/or
    documentation shipped with the product are Certified.
[2] Colors: White
    Number of coats: 1
    Maximum field use dry film thickness (in mils): 16 mils (For Pipe End Use)
    Maximum thinner: None
    Final cure time and temperature: 30 days @ 23°C (Pipe end use only)
    Special comments: For Pipe End Use only: Mix ratio of Part A to Part B is 80:20 by
    volume. No induction period.

Coatings - Tank[1]
SigmaGuard CSF 650[4] >= 2000 gal. CLD 23 EPOXY
Sigmacover 280 + Sigmaguard CSF 650[3] >= 5000 gal. CLD 23 EPOXY 

[1] Only products bearing the NSF Mark on the product, product packaging, and/or
    documentation shipped with the product are Certified.
[3] Colors: Sigmacover 280 (Yellow/Green)+ SigmaGuard CSF 650 (Green) 
    Number of Coats: 2
    Sequence of Coats : Sigmacover 280 (3 mils), SigmaGuard CSF 650 (12 mils)
    Maximum Field Use Dry Film Thickness (in mils): 15 mils
    Maximum Thinner: Sigmacover 280: max 10% thinner 91-92. SigmaGuard CSF 650: None.      
    Recoat Cure Time and Temperature : 3 days at 21°C
    Final Cure Time and Temperature: 8 days at 20ºC
    Special Comments: Mix ratio of Resin: Hardner for both products is 4:1 by volume.First
    coat is Sigmacover 280, which can be thinned max 10% using 91=92 thinner. Second coat is
    SigmaGuard CSF 650, which can't be thinned.  Once final cure is complete, fill tank with
    fresh water tap and allow to soak for 4 days.  After soaking in water for 4 days, rinse
    with high pressure water and drain tank.
[4] Colors: Green, white
    Number of Coats: 1
    Maximum Field Use Dry Film Thickness (in mils): 12
    Maximum Thinner: None
    Final Cure Time and Temperature: 5 days at 20ºC
    Special Comments: Mix ratio of Part A to Part B is 80:20 by volume. No induction period.
    Once cure is complete, fill
    tank with fresh tap water and allow to soak for 4 days. After soaking in water for 4
    days, rinse with high pressure water and drain tank.

Number of matching Manufacturers is 1
Number of matching Products is 8
Processing time was 0 seconds