NSF Product and Service Listings

These NSF Official Listings are current as of Friday, December 26, 2025 at 12:15 a.m. Eastern Time. Please contact NSF to confirm the status of any Listing, report errors, or make suggestions.

Alert: NSF is concerned about fraudulent downloading and manipulation of website text. Always confirm this information by clicking on the below link for the most accurate information: http://info.nsf.org/Certified/PwsComponents/Listings.asp?Company=3R920&Standard=061&


NSF/ANSI/CAN 61
Drinking Water System Components - Health Effects

NOTE: Unless otherwise indicated for Materials, Certification is only for the Water Contact Material shown in the Listing. Click here for a list of Abbreviations used in these Listings. Click here for the definitions of Water Contact Temperatures denoted in these Listings. Products certified to NSF/ANSI/CAN 61 comply with the health effects criteria in NSF/ANSI/CAN 600.

 
Plascoat, an Axalta Coating Systems Company 
Trading Estate Water Lane
Farnham, Surrey GU9 9NY 
United Kingdom 
44 125 273 8205
Visit this company's website


Facility : Surrey, United Kingdom

Protective (Barrier) Materials

    Water Water
  Water Contact Contact Contact
Trade Designation Size Restriction Temp Material

Coatings - Fittings[1]
Abcite 1060 DW Blue[2] [G] >= 50 mm CLD 23 ECPC
Abcite 1060 Jet Black[2] [G] >= 50 mm CLD 23 ECPC
Abcite X60 DW Blue[2] [G] >= 50 mm CLD 23 ECPC
Abcite X60 Jet Black[2] [G] >= 50 mm CLD 23 ECPC
PLASCOAT PPA 571 HES NAR Blue 536[3] >= 4" CLD 23 AMP
Plascoat PPA 571 AQUA[3] >= 4" CLD 23 AMP 

[1] Only products bearing the NSF Mark on the product, product packaging, and/or
    documentation shipped with the product are Certified.
[2] Colors: DW blue, jet black
    Number of Coats: 1 
    Maximum Field Use Dry Film Thickness (in mils): 15 
    Final Cure Time and Temperature: 5 minutes at ambient or until substrate cools down to
    below 150°C.
    Special Comments: Spray Application: Preheat steel substrate for 30 minutes at 250°C and
    spray Abcite X60 on the substrate before the substrate temperature decreases below
    180°C. Preheating temperature may need to be adjusted for substrate thickness. 
    Fluidized Bed Application: preheat steel substrate for 30 minutes at 250°C, dip in a
    fluidized bed of Abcite 1060 for 5-8 seconds.  Preheating temperature may need to be
    adjusted depending on substrate thickness.
    
[3] Colors: Blue
    Number of Coats: 1 - 2
    Maximum Field Use Dry Film Thickness (in mils): 32
    Recoat Cure Time and Temperature: Preheat metal substrate to 180°C - 200°C.  Post-heat
    to 180°C - 200°C for 2-5 minutes.
    Final Cure Time and Temperature: Preheat metal to 180°C - 200°C.  Post heat to 180°C -
    200°C for 2-5 minutes.
[G] Product is Certified to NSF/ANSI/CAN 372 and conforms with the lead content requirements
    for "lead free" plumbing as defined by California, Vermont, Maryland, and Louisiana
    state laws and the U.S. Safe Drinking Water Act.

Coatings - Pipe[1]
Abcite 1060 DW Blue[2] [G] >= 50 mm CLD 23 ECPC
Abcite 1060 Jet Black[2] [G] >= 50 mm CLD 23 ECPC
Abcite X60 DW Blue[2] [G] >= 50 mm CLD 23 ECPC
Abcite X60 Jet Black[2] [G] >= 50 mm CLD 23 ECPC
PLASCOAT PPA 571 HES NAR Blue 536[3] >= 4" CLD 23 AMP
Plascoat PPA 571 AQUA[3] >= 4" CLD 23 AMP 

[1] Only products bearing the NSF Mark on the product, product packaging, and/or
    documentation shipped with the product are Certified.
[2] Colors: DW blue, jet black
    Number of Coats: 1 
    Maximum Field Use Dry Film Thickness (in mils): 15 
    Final Cure Time and Temperature: 5 minutes at ambient or until substrate cools down to
    below 150°C.
    Special Comments: Spray Application: Preheat steel substrate for 30 minutes at 250°C and
    spray Abcite X60 on the substrate before the substrate temperature decreases below
    180°C. Preheating temperature may need to be adjusted for substrate thickness. 
    Fluidized Bed Application: preheat steel substrate for 30 minutes at 250°C, dip in a
    fluidized bed of Abcite 1060 for 5-8 seconds.  Preheating temperature may need to be
    adjusted depending on substrate thickness.
    
[3] Colors: Blue
    Number of Coats: 1 - 2
    Maximum Field Use Dry Film Thickness (in mils): 32
    Recoat Cure Time and Temperature: Preheat metal substrate to 180°C - 200°C.  Post-heat
    to 180°C - 200°C for 2-5 minutes.
    Final Cure Time and Temperature: Preheat metal to 180°C - 200°C.  Post heat to 180°C -
    200°C for 2-5 minutes.
[G] Product is Certified to NSF/ANSI/CAN 372 and conforms with the lead content requirements
    for "lead free" plumbing as defined by California, Vermont, Maryland, and Louisiana
    state laws and the U.S. Safe Drinking Water Act.

Coatings - Tank[1] [2] [G]
Abcite 1060 DW Blue >= 10 gal. CLD 23 ECPC
Abcite 1060 Jet Black >= 10 gal. CLD 23 ECPC
Abcite X60 DW Blue >= 10 gal. CLD 23 ECPC
Abcite X60 Jet Black >= 10 gal. CLD 23 ECPC 

[1] Only products bearing the NSF Mark on the product, product packaging, and/or
    documentation shipped with the product are Certified.
[2] Colors: DW blue, jet black
    Number of Coats: 1 
    Maximum Field Use Dry Film Thickness (in mils): 15 
    Final Cure Time and Temperature: 5 minutes at ambient or until substrate cools down to
    below 150°C.
    Special Comments: Spray Application: Preheat steel substrate for 30 minutes at 250°C and
    spray Abcite X60 on the substrate before the substrate temperature decreases below
    180°C. Preheating temperature may need to be adjusted for substrate thickness. 
    Fluidized Bed Application: preheat steel substrate for 30 minutes at 250°C, dip in a
    fluidized bed of Abcite 1060 for 5-8 seconds.  Preheating temperature may need to be
    adjusted depending on substrate thickness.
    
[G] Product is Certified to NSF/ANSI/CAN 372 and conforms with the lead content requirements
    for "lead free" plumbing as defined by California, Vermont, Maryland, and Louisiana
    state laws and the U.S. Safe Drinking Water Act.

Coatings - Valve[1] [2] [G]
Abcite 1060 DW Blue >= 50 mm CLD 23 ECPC
Abcite 1060 Jet Black >= 50 mm CLD 23 ECPC
Abcite X60 DW Blue >= 50 mm CLD 23 ECPC
Abcite X60 Jet Black >= 50 mm CLD 23 ECPC 

[1] Only products bearing the NSF Mark on the product, product packaging, and/or
    documentation shipped with the product are Certified.
[2] Colors: DW blue, jet black
    Number of Coats: 1 
    Maximum Field Use Dry Film Thickness (in mils): 15 
    Final Cure Time and Temperature: 5 minutes at ambient or until substrate cools down to
    below 150°C.
    Special Comments: Spray Application: Preheat steel substrate for 30 minutes at 250°C and
    spray Abcite X60 on the substrate before the substrate temperature decreases below
    180°C. Preheating temperature may need to be adjusted for substrate thickness. 
    Fluidized Bed Application: preheat steel substrate for 30 minutes at 250°C, dip in a
    fluidized bed of Abcite 1060 for 5-8 seconds.  Preheating temperature may need to be
    adjusted depending on substrate thickness.
    
[G] Product is Certified to NSF/ANSI/CAN 372 and conforms with the lead content requirements
    for "lead free" plumbing as defined by California, Vermont, Maryland, and Louisiana
    state laws and the U.S. Safe Drinking Water Act.

Number of matching Manufacturers is 1
Number of matching Products is 20
Processing time was 0 seconds