NSF Product and Service Listings

These NSF Official Listings are current as of Wednesday, May 31, 2023 at 12:15 a.m. Eastern Time. Please contact NSF to confirm the status of any Listing, report errors, or make suggestions.

Alert: NSF is concerned about fraudulent downloading and manipulation of website text. Always confirm this information by clicking on the below link for the most accurate information: http://info.nsf.org/Certified/PwsComponents/Listings.asp?Company=41060&Standard=061&


NSF/ANSI/CAN 61
Drinking Water System Components - Health Effects

NOTE: Unless otherwise indicated for Materials, Certification is only for the Water Contact Material shown in the Listing. Click here for a list of Abbreviations used in these Listings. Click here for the definitions of Water Contact Temperatures denoted in these Listings. Products certified to NSF/ANSI/CAN 61 comply with the health effects criteria in NSF/ANSI/CAN 600.

 
Simpson Strong-Tie Company 
5956 West Las Positas Boulevard
Pleasanton, CA 94588 
United States 
800-999-5099


Facility : West Chicago, IL

Joining and Sealing Materials

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Adhesives
AT-XP [1] CLD 23 ACR
AT-XP10 [1] CLD 23 ACR
AT-XP13 [1] CLD 23 ACR
AT-XP30 [1] CLD 23 ACR
ET-3G [2] CLD 23 EPOXY
SET High Strength Epoxy [2] CLD 23 EPOXY
SET-3G [2] CLD 23 EPOXY
SET-PAC [2] CLD 23 EPOXY
SET-XP [2] CLD 23 EPOXY
SET-XP22 [2] CLD 23 EPOXY
SET22 [2] CLD 23 EPOXY
SET56 [2] CLD 23 EPOXY
SETPAC-EZ [2] CLD 23 EPOXY 

[1] Certified for a maximum exposed surface area of 25 sq. in./1000 gal.
[2] Certified for a maximum exposed surface area of 216 sq. in./1000 gal.

Sealants
CI-LV [3] CLD 23 EPOXY
CILV32 [3] CLD 23 EPOXY
CILVKT3 [3] CLD 23 EPOXY
ET-3G [2] CLD 23 EPOXY
ETI-LV Injection Epoxy [4] CLD 23 EPOXY
ETILV [4] CLD 23 EPOXY
ETILV22 [4] CLD 23 EPOXY
SET High Strength Epoxy [2] CLD 23 EPOXY
SET-3G [2] CLD 23 EPOXY
SET-PAC [2] CLD 23 EPOXY
SET-XP [2] CLD 23 EPOXY
SET-XP22 [2] CLD 23 EPOXY
SET22 [2] CLD 23 EPOXY
SET56 [2] CLD 23 EPOXY
SETPAC-EZ [2] CLD 23 EPOXY 

[2] Certified for a maximum exposed surface area of 216 sq. in./1000 gal.
[3] Certified for a maximum surface area of 568 square inches per 1000 gallons.  Mix ratio
    2:1 (Resin:Cure).
[4] Certified for a maximum exposed surface area of 22 sq. in./1000 gal.


Protective (Barrier) Materials

    Water Water
  Water Contact Contact Contact
Trade Designation Size Restriction Temp Material

Coatings - Fittings[1]
Simpson Strong-Tie Composite Strengthening System >= 1" CLD 23 EPOXY 

[1] Product is applied in multiple layers with Layers 1,2, and 3 optional:
    Protective (Barrier) Materials
    Layer 1: CSS-ES Epoxy Primer and Saturant apply 10 wet mils maximum.  Mix ratio of Part
    A to B is 2:1 by volume.  Mix with a drill and mixing paddle until uniformly blended (5
    minutes at 500 rpm).  Apply 1 coat.
    Layer 2: CSS-EP Paste Filler apply 40 wet mils maximum.  Mix ratio of Part A to B is 2:1
    by volume.  Mix with a drill and mixing paddle until uniformly blended (5 minutes at 500
    rpm). Apply 1 coat.
    Layer 3: CSS-CUGF27 Fabric saturated with CSS-ES Epoxy Primer and Saturant (follow
    mixing instructions above).  Apply with maximum thickness of 50 mils.  It is permitted
    to place Layer 3 between layers of carbon fabric (Layers 4+).
    Layer 4+: CSS-CUCF11, CSS-CUCF22, or CSS-CUCF44 Fabric saturated with CSS-ES Epoxy
    Primer and Saturant (follow mixing instructions above).  Apply 1 - 10 layers with a
    maximum thickness of 20 mils per layer of CSS-CUCF11, 40 mils per layer of CSS-CUCF22,
    or 80 mils per layer of CSS-CUCF44.
    Saturation rate for fabrics:  1 gallon per 75 square feet of CSS-CUCF11; 1 gallon per 50
    square feet of CSS-CUCF22; 1 gallon per 50 square feet of CSS-CUGF27; and 1 gallon per
    25 square feet of CSS-CUCF44.
    Final cure time is 72 hours at 70°F after application of final layer.  There is no cure
    between the application of layers.

Coatings - Pipe - Immediate Return to Service[1]
Simpson Strong-Tie Composite Strengthening System >= 60" CLD 23 EPOXY 

[1] Product is applied in multiple layers with Layers 1,2, and 3 optional:
    Protective (Barrier) Materials
    Layer 1: CSS-ES Epoxy Primer and Saturant apply 10 wet mils maximum.  Mix ratio of Part
    A to B is 2:1 by volume.  Mix with a drill and mixing paddle until uniformly blended (5
    minutes at 500 rpm).  Apply 1 coat.
    Layer 2: CSS-EP Paste Filler apply 40 wet mils maximum.  Mix ratio of Part A to B is 2:1
    by volume.  Mix with a drill and mixing paddle until uniformly blended (5 minutes at 500
    rpm). Apply 1 coat.
    Layer 3: CSS-CUGF27 Fabric saturated with CSS-ES Epoxy Primer and Saturant (follow
    mixing instructions above).  Apply with maximum thickness of 50 mils.  It is permitted
    to place Layer 3 between layers of carbon fabric (Layers 4+).
    Layer 4+: CSS-CUCF11, CSS-CUCF22, or CSS-CUCF44 Fabric saturated with CSS-ES Epoxy
    Primer and Saturant (follow mixing instructions above).  Apply 1 - 10 layers with a
    maximum thickness of 20 mils per layer of CSS-CUCF11, 40 mils per layer of CSS-CUCF22,
    or 80 mils per layer of CSS-CUCF44.
    Saturation rate for fabrics:  1 gallon per 75 square feet of CSS-CUCF11; 1 gallon per 50
    square feet of CSS-CUCF22; 1 gallon per 50 square feet of CSS-CUGF27; and 1 gallon per
    25 square feet of CSS-CUCF44.
    Final cure time is 72 hours at 70°F after application of final layer.  There is no cure
    between the application of layers.

Coatings - Tank[1]
Simpson Strong-Tie Composite Strengthening System >= 6,000 gal. CLD 23 EPOXY 

[1] Product is applied in multiple layers with Layers 1,2, and 3 optional:
    Protective (Barrier) Materials
    Layer 1: CSS-ES Epoxy Primer and Saturant apply 10 wet mils maximum.  Mix ratio of Part
    A to B is 2:1 by volume.  Mix with a drill and mixing paddle until uniformly blended (5
    minutes at 500 rpm).  Apply 1 coat.
    Layer 2: CSS-EP Paste Filler apply 40 wet mils maximum.  Mix ratio of Part A to B is 2:1
    by volume.  Mix with a drill and mixing paddle until uniformly blended (5 minutes at 500
    rpm). Apply 1 coat.
    Layer 3: CSS-CUGF27 Fabric saturated with CSS-ES Epoxy Primer and Saturant (follow
    mixing instructions above).  Apply with maximum thickness of 50 mils.  It is permitted
    to place Layer 3 between layers of carbon fabric (Layers 4+).
    Layer 4+: CSS-CUCF11, CSS-CUCF22, or CSS-CUCF44 Fabric saturated with CSS-ES Epoxy
    Primer and Saturant (follow mixing instructions above).  Apply 1 - 10 layers with a
    maximum thickness of 20 mils per layer of CSS-CUCF11, 40 mils per layer of CSS-CUCF22,
    or 80 mils per layer of CSS-CUCF44.
    Saturation rate for fabrics:  1 gallon per 75 square feet of CSS-CUCF11; 1 gallon per 50
    square feet of CSS-CUCF22; 1 gallon per 50 square feet of CSS-CUGF27; and 1 gallon per
    25 square feet of CSS-CUCF44.
    Final cure time is 72 hours at 70°F after application of final layer.  There is no cure
    between the application of layers.

Number of matching Manufacturers is 1
Number of matching Products is 31
Processing time was 0 seconds