NSF Product and Service Listings
These NSF Official Listings are current as of Monday, July 8, 2024 at 12:15 a.m. Eastern Time. Please contact NSF to confirm the status of any Listing, report errors, or make suggestions.
Alert: NSF is concerned about fraudulent downloading and manipulation of website text. Always confirm this information by clicking on the below link for the most accurate information: http://info.nsf.org/Certified/PwsComponents/Listings.asp?Company=46690&Standard=061&
NSF/ANSI/CAN 61
Drinking Water System Components - Health Effects
Drinking Water System Components - Health Effects
NOTE: Unless otherwise indicated for Materials, Certification is only for the Water Contact Material shown in the Listing. Click here for a list of Abbreviations used in these Listings. Click here for the definitions of Water Contact Temperatures denoted in these Listings. Products certified to NSF/ANSI/CAN 61 comply with the health effects criteria in NSF/ANSI/CAN 600.
| Tnemec Company, Inc. | |
| 6800 Corporate Drive | |
| Kansas City, MO 64120-1372 | |
| United States | |
| 816-474-3400 | |
| Visit this company's website |
Facility : Baltimore, MD
Protective (Barrier) Materials
| Water | Water | |||
| Water Contact | Contact | Contact | ||
| Trade Designation | Size Restriction | Temp | Material | |
|
Coatings - Fittings |
||||
| 22 Epoxoline[1] [2] | >= 1/2" | CLD 23 | EPOXY | |
| N140F Pota-Pox Plus Fast Cure [2] [3] | >= 2" | CLD 23 | EPOXY | |
| Series 21 Epoxoline[2] [4] | >= 1" | CLD 23 | EPOXY | |
| Series 91-H2O ™ Hydro-Zinc™ [2] [6] [7] | >= 1" | CLD 23 | EPOXY | |
| Series 91-H2O ™ Hydro-Zinc™ [2] [5] [6] | >= 1/2" | CLD 23 | EPOXY | |
| Series 93-H20 Hydro-Zinc[8] | >= 1" | CLD 23 | PUR | |
| Series 94-H2O Hydro-Zinc[2] [9] | [10] | CLD 23 | PUR | |
| Series L140 Pota-Pox Plus [2] [11] | >= 1" | CLD 23 | EPOXY | |
| Series L140F Pota-Pox Plus Fast Cure [2] [12] | >= 1" | CLD 23 | EPOXY | |
| Series N140 Pota-Pox Plus[2] [13] | >= 2" | CLD 23 | EPOXY | |
| Series N140 Pota-Pox Plus[14] [15] | >= 4" | CLD 23 | EPOXY | |
| Series N140F Pota-Pox Plus Fast Cure[15] [16] | >= 4" | CLD 23 | EPOXY | |
[1] Colors: 1255 Beige, 1218 Blue, WH11 White
Number of Coats: 1-2
Maximum Field Use Dry Film Thickness (in mils): 50
Maximum Thinner: 5% Thinner #2
Recoat Cure Time and Temperature: 16 hours at 75°F
Final Cure Time and Temperature: 5 days at 75°F
Special Comments: Mix ratio of Part A to Part B is 1:1 by volume. Optional use with
fiberglass flake S211-0220. The fiberglass flake can be added up to a rate of 1% by
weight after the Parts A and B are mixed together. Certified for use as a primer or
topcoat with any NSF Certified Tnemec coating system provided that both primer and
topcoat meet their individual certified end uses.
[2] Meets the health effects requirements of NSF/ANSI/CAN 600 according to the requirements
of NSF/ANSI/CAN 61 including the most current health effects criteria for xylenes,
toluene, and ethylbenzene.
[3] Colors: 15BL Tank White, 1255 Beige, 1211 Red, 35GR Black, 39BL Delft Blue, Y2606 Romac
Yellow, 00WH Tnemec White, 11SF True Blue, B9118 Baker Blue, B5712 Westech Blue, B2592
RAL 5009 Azurblau, B9695 Houston Blue, A14130 Mueller Gray, R5477 Mueller Sienna Red.
Number of Coats: 1
Sequence of Coats: 4 mils
Maximum Thinner: 10% No. 4 Thinner by volume
Recoat Cure Time and Temperature: 5 hours at 75F
Final Cure Time/Temperature: 7 days at 75F (entire system)
Special Comments: Mix ration is 1 Part A to 1 Part B by volume. Certified for use as an
optional primer or intermediate topcoat with any Tnemec NSF certified primer and topcoat
coating system provided the primer, intermediate, and topcoat meet their certified end
uses.
[4] Colors: WH16 OFF-WHITE, 35GR Black, 33GR Gray, 39BL Delft Blue, 1255 Beige, B5712
Westech Blue, 11SF True Blue/Safety, 1211 Red Primer, A13096 Baker Dark Gray, B2592
RAL5009 Azurblau, B2506 Dezurik Blue, B9918 New Baker Blue
Number of Coats: 1-3
Maximum Field Use Dry Thickness (in mils): 20
Maximum Thinner: 5% F041-0088 Thinner Clear by volume
Recoat Cure Time and Temperature: 8 hours at 75F
Final Cure Time/Temperature: 7 days at 75F
Special Comments: Mix ratio of A:B is 2:1 by volume. Series 21 Epoxoline is approved for
use as a primer or topcoat with any NSF Certified Tnemec topcoat or coating system
providing that both primer and topcoat meet their individual Certified end uses.
[5] This coating used with Thinner #3 is Certified for use in pipes >=24", tanks >=1500
gallons, fittings >=1/2", pumps >=1/2", valves >=2".
[6] Colors: Greenish-Gray
Number of Coats: 1
Maximum Field Use Dry Thickness (in mils): 4
Maximum Thinner: 10% Thinner #2 or Thinner #3 by volume
Final Cure Time/Temperature: 4 hours at 75F; 2 hours at 75F wen accelerator is used.
Special Comments: Series 44-710 Urethane Accelerator may be added up to 4 fl.oz/gal.
Series 91-H2O Hydro-Zinc ™ is approved for use with any NSF Certified Tnemec topcoat or
coatings system providing that both primer and topcoat meet their individual Certified
end uses. Mix Ratio Part A:B is 70%:30% by volume.
[7] This coating used with Thinner #2 is Certified for use in pipes >=24", tanks >=3000
gallons, fittings >=1", pumps >=1/2", and valves >=4".
[8] Colors: Greenish-Gray
Maximum Field Use Dry Thickness(in mils): 4 mils
Maximum Thinner: 10% Thinner #2 by volume
Final Cure Time/Temperature: 8 hours at 75F. 4 hours at 75F if accelerator is used.
Special Comments: Series 44-710 accelerator may be used up to 4 fluid oz/gal. 93-H20
Hydro-Zinc is approved for use with any NSF Certified Tnemec topcoat or coating system
providing that both primer and topcoat meet their individual Certified end uses.
[9] Colors: Greenish-gray
Number of Coats: 1
Maximum Field Use Dry Film Thickness (in mils): 4
Maximum Thinner: 15% Tnemec No. 49 or 10% Thinner No. 2 or 10% Thinner No. 3 by volume
Final Cure Time and Temperature: 8 hours at 75°F; 2 hours at 75°F when the accelerator
is used
Special Comments: Series 44-710 Urethane Accelerator may be added up to 4 fl. oz/gal.
94-H2O is aproved for use with any NSF Certified Tnemec topcoat or coating system.
[10] This coating used with Thinner #49 is Certified for use in fittings >= 1/2". This
coating used with Thinner #2 is Certified for use in fittings >= 1". This coatings used
with Thinner #3 is Certified for use in fittings >= 1/2".
[11] Colors: 1255 Beige, 15BL Tank White, 1211 Red, 00WH White
# of coats: 2-3
# Seq Of Coats: Any combination of listed colors
Max Film Thickness: 18 (Maximum of 6 mils per coat)
Max Thinner: 5% Tnemec No. 49 Thinner by volume
Recoat Cure Time/ Temp.: 16 hours at 75° F
Final Cure Time/ Temp.: 7 days at 75° F
Special Comments: Series N140, N140F, V140, V140F, L140 and Series 22, FC22 may be
substituted as a primer or topcoat for L140 provided that both primer and topcoat meet
their individual Certified end uses. Series 44-700 accelerator (Part C) may be added up
to 4 fluid ounces per two mixed gallons of L140 Parts A and B. Mix ratio of A:B is 1:1
by volume.
[12] Colors: 1255 Beige, 15BL Tank White, 1211 Red, 00WH White
# of coats: 2-3
# Seq Of Coats: Any combination of listed colors
Max Film Thickness: 18 (Maximum of 6 mils per coat)
Max Thinner: 5% Tnemec No. 49 Thinner by volume
Recoat Cure Time/ Temp.: 16 hours at 75° F
Final Cure Time/ Temp.: 7 days at 75° F
Special Comments: Series N140, N140F, V140, V140F, L140 and Series 22, FC22 may be
substituted as a primer or topcoat for L140F provided that both primer and topcoat meet
their individual Certified end uses. Mix ratio of Part A to Part B is 1:1 by volume.
[13] Colors: 00WH Tnemec White, 1211 Red, 1255 Beige, 15BL Tank white, 35GR Black, 39BL Delft
blue, B5712 Westech Blue, 11SF True Blue, B9118 Baker Blue, B8314 Krausz Blue, Y2606
Romac Yellow, B2592 RAL 5009 Azurblau, B7011 Crispin Blue, B2506 Dezurik Blue, A14130
Mueller Gray, B9695 Houston Blue, R5477 Mueller Sienna Red.
Number of Coats: 1
Maximum Field Use Dry Thickness(in mils): 4 mils
Maximum Thinner: 10% No. 4 Thinner by volume
Recoat Cure Time and Temperature: 5 hours at 75°F
Final Cure Time and Temperature: 7 days at 75°F (entire system)
Special Comments: Mix ratio is 1 Part A to 1 Part B by volume. Certified for use as an
optional primer or intermediate coat with any Tnemec NSF certified primer and topcoat
coating system provided the primer, intermediate, and topcoat meet their certified end
uses.
[14] Colors: 00WH Tnemec White, 1211 Red, 1255 Beige, 15BL Tank White, 35GR Black, 39BL Delft
Blue, B5712 Westech Blue, 11SF True Blue, B9118 Baker Blue, B8314 Krausz Blue, A13096
Baker Dark Gray, Y2606 Romac Yellow, B2592 RAL 5009 Azurblau, B7011 Crispin Blue, B2506
Dezurik Blue, A14130 Mueller Gray, B9695 Houston Blue, R5477 Mueller Sienna Red.
Number of Coats: 2-3
Sequence of Coats: Any combination of Listed colors
Maximum Field Use Dry Film Thickness (in mils): 18
Maximum Thinner: 5% Tnemec No. 60 Thinner by volume
Recoat Cure Time and Temperature: 5 hours at 75°F with accelerator, 9 hours at 75°F
without accelerator
Final Cure Time and Temperature: 30 days at 75°F
Special Comments: Any Listed color of Series 22, FC22, or N140, may be substituted as a
primer of topcoat for Series N140 Pota-Pox Plus provided that both primer and topcoat
meet their individual Certified end uses. The mix ratio of Part A:Part B is 1:1 by
volume. Part C (Series 44-700 Accelerator) is an optional additive to Part A in the
field and may be added at up to 4 fluid ounces per 2 mixed gallons of parts A and B.
[15] Meets the health effects requirements of NSF/ANSI/CAN 600 according to requirements of
NSF/ANSI/CAN 61 for pump, valve, and fitting end use.
[16] Colors: 00WH Tnemec White, 1211 Red, 1255 Beige, 15BL Tank white, 35GR Black, 39BL Delft
Blue, B2506 DeZurik Blue, B5712 Westech Blue, 11SF True Blue, B9118 Baker Blue, B7896
S-B Blue, Y2606 Romac Yellow, B2592 RAL 5009 Azurblau, B7011 Crispin Blue, B9695 Houston
Blue, A14130 Mueller Gray, R5477 Mueller Sienna Red.
Number of Coats: 2-3
Sequence of Coats: Any combination of Listed colors
Maximum Field Use Dry film Thickness (in mils): 18
Maximum Thinner: 5% Tnemec No. 60 Thinner by volume
Recoat Cure Time and Temperature: 5 hours at 75°F
Final Cure Time and Temperature: 30 days at 75°F
Special Comments: Any listed color of series 22, FC22, or N140 may be substituted as a
primer or topcoat for the Series N140 Pota-Pox Plus provided that both primer and
topcoat meet their individual Certified end uses. Mix ratio of Part A:Part B is 1:1 by
volume.
|
||||
|
Coatings - Mechanical Devices |
||||
| 22 Epoxoline [1] [2] | [26] | CLD 23 | EPOXY | |
| Series 21 Epoxoline[2] [4] | [23] | CLD 23 | EPOXY | |
| Series 91-H2O™ Hydro-Zinc™ [2] [5] [6] [7] | [24] | CLD 23 | PUR | |
| Series 93-H20 Hydro-Zinc[8] | [27] | CLD 23 | PUR | |
| Series 94-H2O Hydro Zinc [2] [9] | [24] [25] | CLD 23 | PUR | |
| Series N140 Pota-Pox Plus[14] [15] | [22] | CLD 23 | EPOXY | |
| Series N140F Pota-Pox Plus Fast Cure[15] [16] | [22] | CLD 23 | EPOXY | |
[1] Colors: 1255 Beige, 1218 Blue, WH11 White
Number of Coats: 1-2
Maximum Field Use Dry Film Thickness (in mils): 50
Maximum Thinner: 5% Thinner #2
Recoat Cure Time and Temperature: 16 hours at 75°F
Final Cure Time and Temperature: 5 days at 75°F
Special Comments: Mix ratio of Part A to Part B is 1:1 by volume. Optional use with
fiberglass flake S211-0220. The fiberglass flake can be added up to a rate of 1% by
weight after the Parts A and B are mixed together. Certified for use as a primer or
topcoat with any NSF Certified Tnemec coating system provided that both primer and
topcoat meet their individual certified end uses.
[2] Meets the health effects requirements of NSF/ANSI/CAN 600 according to the requirements
of NSF/ANSI/CAN 61 including the most current health effects criteria for xylenes,
toluene, and ethylbenzene.
[4] Colors: WH16 OFF-WHITE, 35GR Black, 33GR Gray, 39BL Delft Blue, 1255 Beige, B5712
Westech Blue, 11SF True Blue/Safety, 1211 Red Primer, A13096 Baker Dark Gray, B2592
RAL5009 Azurblau, B2506 Dezurik Blue, B9918 New Baker Blue
Number of Coats: 1-3
Maximum Field Use Dry Thickness (in mils): 20
Maximum Thinner: 5% F041-0088 Thinner Clear by volume
Recoat Cure Time and Temperature: 8 hours at 75F
Final Cure Time/Temperature: 7 days at 75F
Special Comments: Mix ratio of A:B is 2:1 by volume. Series 21 Epoxoline is approved for
use as a primer or topcoat with any NSF Certified Tnemec topcoat or coating system
providing that both primer and topcoat meet their individual Certified end uses.
[5] This coating used with Thinner #3 is Certified for use in pipes >=24", tanks >=1500
gallons, fittings >=1/2", pumps >=1/2", valves >=2".
[6] Colors: Greenish-Gray
Number of Coats: 1
Maximum Field Use Dry Thickness (in mils): 4
Maximum Thinner: 10% Thinner #2 or Thinner #3 by volume
Final Cure Time/Temperature: 4 hours at 75F; 2 hours at 75F wen accelerator is used.
Special Comments: Series 44-710 Urethane Accelerator may be added up to 4 fl.oz/gal.
Series 91-H2O Hydro-Zinc ™ is approved for use with any NSF Certified Tnemec topcoat or
coatings system providing that both primer and topcoat meet their individual Certified
end uses. Mix Ratio Part A:B is 70%:30% by volume.
[7] This coating used with Thinner #2 is Certified for use in pipes >=24", tanks >=3000
gallons, fittings >=1", pumps >=1/2", and valves >=4".
[8] Colors: Greenish-Gray
Maximum Field Use Dry Thickness(in mils): 4 mils
Maximum Thinner: 10% Thinner #2 by volume
Final Cure Time/Temperature: 8 hours at 75F. 4 hours at 75F if accelerator is used.
Special Comments: Series 44-710 accelerator may be used up to 4 fluid oz/gal. 93-H20
Hydro-Zinc is approved for use with any NSF Certified Tnemec topcoat or coating system
providing that both primer and topcoat meet their individual Certified end uses.
[9] Colors: Greenish-gray
Number of Coats: 1
Maximum Field Use Dry Film Thickness (in mils): 4
Maximum Thinner: 15% Tnemec No. 49 or 10% Thinner No. 2 or 10% Thinner No. 3 by volume
Final Cure Time and Temperature: 8 hours at 75°F; 2 hours at 75°F when the accelerator
is used
Special Comments: Series 44-710 Urethane Accelerator may be added up to 4 fl. oz/gal.
94-H2O is aproved for use with any NSF Certified Tnemec topcoat or coating system.
[14] Colors: 00WH Tnemec White, 1211 Red, 1255 Beige, 15BL Tank White, 35GR Black, 39BL Delft
Blue, B5712 Westech Blue, 11SF True Blue, B9118 Baker Blue, B8314 Krausz Blue, A13096
Baker Dark Gray, Y2606 Romac Yellow, B2592 RAL 5009 Azurblau, B7011 Crispin Blue, B2506
Dezurik Blue, A14130 Mueller Gray, B9695 Houston Blue, R5477 Mueller Sienna Red.
Number of Coats: 2-3
Sequence of Coats: Any combination of Listed colors
Maximum Field Use Dry Film Thickness (in mils): 18
Maximum Thinner: 5% Tnemec No. 60 Thinner by volume
Recoat Cure Time and Temperature: 5 hours at 75°F with accelerator, 9 hours at 75°F
without accelerator
Final Cure Time and Temperature: 30 days at 75°F
Special Comments: Any Listed color of Series 22, FC22, or N140, may be substituted as a
primer of topcoat for Series N140 Pota-Pox Plus provided that both primer and topcoat
meet their individual Certified end uses. The mix ratio of Part A:Part B is 1:1 by
volume. Part C (Series 44-700 Accelerator) is an optional additive to Part A in the
field and may be added at up to 4 fluid ounces per 2 mixed gallons of parts A and B.
[15] Meets the health effects requirements of NSF/ANSI/CAN 600 according to requirements of
NSF/ANSI/CAN 61 for pump, valve, and fitting end use.
[16] Colors: 00WH Tnemec White, 1211 Red, 1255 Beige, 15BL Tank white, 35GR Black, 39BL Delft
Blue, B2506 DeZurik Blue, B5712 Westech Blue, 11SF True Blue, B9118 Baker Blue, B7896
S-B Blue, Y2606 Romac Yellow, B2592 RAL 5009 Azurblau, B7011 Crispin Blue, B9695 Houston
Blue, A14130 Mueller Gray, R5477 Mueller Sienna Red.
Number of Coats: 2-3
Sequence of Coats: Any combination of Listed colors
Maximum Field Use Dry film Thickness (in mils): 18
Maximum Thinner: 5% Tnemec No. 60 Thinner by volume
Recoat Cure Time and Temperature: 5 hours at 75°F
Final Cure Time and Temperature: 30 days at 75°F
Special Comments: Any listed color of series 22, FC22, or N140 may be substituted as a
primer or topcoat for the Series N140 Pota-Pox Plus provided that both primer and
topcoat meet their individual Certified end uses. Mix ratio of Part A:Part B is 1:1 by
volume.
[22] Certified for mechanical device end use (other than pump and valve) for a maximum of 4.6
sq. ft. per gpm.
[23] Certified for mechanical device end use (other than pump and valve) for a maximum of
50.5 sq. ft. per gpm.
[24] Certified for mechanical device end use (other than pump and valve) for a maximum of 151
sq. ft. per gpm when used with Thinner #2 and 189 sq. ft. per gpm when used with Thinner
#3.
[25] This coating used with Thinner #49 is Certified for mechanical device end use (other
than pump and valve) for a maximum of 310 sq. ft. per gpm.
[26] Certified for mechanical device end use (other than pump and valve) for a maximum of 635
sq. ft. per gpm.
[27] Certified for mechanical device end use (other than pump and valve) for a maximum of 151
sq. ft per gpm.
|
||||
|
Coatings - Pipe |
||||
| 22 Epoxoline[1] [2] | >= 10" | CLD 23 | EPOXY | |
| N140F Pota-Pox Plus Fast Cure [2] [3] | >= 36" | CLD 23 | EPOXY | |
| Series 91-H2O ™ Hydro-Zinc™ [2] [5] [6] [7] | >= 24" | CLD 23 | EPOXY | |
| Series 93-H20 Hydro-Zinc[8] | >= 24" | CLD 23 | PUR | |
| Series 94-H2O Hydro-Zinc[2] [9] | [17] | CLD 23 | PUR | |
| Series N140 Pota-Pox Plus[2] [13] | >= 36" | CLD 23 | EPOXY | |
[1] Colors: 1255 Beige, 1218 Blue, WH11 White
Number of Coats: 1-2
Maximum Field Use Dry Film Thickness (in mils): 50
Maximum Thinner: 5% Thinner #2
Recoat Cure Time and Temperature: 16 hours at 75°F
Final Cure Time and Temperature: 5 days at 75°F
Special Comments: Mix ratio of Part A to Part B is 1:1 by volume. Optional use with
fiberglass flake S211-0220. The fiberglass flake can be added up to a rate of 1% by
weight after the Parts A and B are mixed together. Certified for use as a primer or
topcoat with any NSF Certified Tnemec coating system provided that both primer and
topcoat meet their individual certified end uses.
[2] Meets the health effects requirements of NSF/ANSI/CAN 600 according to the requirements
of NSF/ANSI/CAN 61 including the most current health effects criteria for xylenes,
toluene, and ethylbenzene.
[3] Colors: 15BL Tank White, 1255 Beige, 1211 Red, 35GR Black, 39BL Delft Blue, Y2606 Romac
Yellow, 00WH Tnemec White, 11SF True Blue, B9118 Baker Blue, B5712 Westech Blue, B2592
RAL 5009 Azurblau, B9695 Houston Blue, A14130 Mueller Gray, R5477 Mueller Sienna Red.
Number of Coats: 1
Sequence of Coats: 4 mils
Maximum Thinner: 10% No. 4 Thinner by volume
Recoat Cure Time and Temperature: 5 hours at 75F
Final Cure Time/Temperature: 7 days at 75F (entire system)
Special Comments: Mix ration is 1 Part A to 1 Part B by volume. Certified for use as an
optional primer or intermediate topcoat with any Tnemec NSF certified primer and topcoat
coating system provided the primer, intermediate, and topcoat meet their certified end
uses.
[5] This coating used with Thinner #3 is Certified for use in pipes >=24", tanks >=1500
gallons, fittings >=1/2", pumps >=1/2", valves >=2".
[6] Colors: Greenish-Gray
Number of Coats: 1
Maximum Field Use Dry Thickness (in mils): 4
Maximum Thinner: 10% Thinner #2 or Thinner #3 by volume
Final Cure Time/Temperature: 4 hours at 75F; 2 hours at 75F wen accelerator is used.
Special Comments: Series 44-710 Urethane Accelerator may be added up to 4 fl.oz/gal.
Series 91-H2O Hydro-Zinc ™ is approved for use with any NSF Certified Tnemec topcoat or
coatings system providing that both primer and topcoat meet their individual Certified
end uses. Mix Ratio Part A:B is 70%:30% by volume.
[7] This coating used with Thinner #2 is Certified for use in pipes >=24", tanks >=3000
gallons, fittings >=1", pumps >=1/2", and valves >=4".
[8] Colors: Greenish-Gray
Maximum Field Use Dry Thickness(in mils): 4 mils
Maximum Thinner: 10% Thinner #2 by volume
Final Cure Time/Temperature: 8 hours at 75F. 4 hours at 75F if accelerator is used.
Special Comments: Series 44-710 accelerator may be used up to 4 fluid oz/gal. 93-H20
Hydro-Zinc is approved for use with any NSF Certified Tnemec topcoat or coating system
providing that both primer and topcoat meet their individual Certified end uses.
[9] Colors: Greenish-gray
Number of Coats: 1
Maximum Field Use Dry Film Thickness (in mils): 4
Maximum Thinner: 15% Tnemec No. 49 or 10% Thinner No. 2 or 10% Thinner No. 3 by volume
Final Cure Time and Temperature: 8 hours at 75°F; 2 hours at 75°F when the accelerator
is used
Special Comments: Series 44-710 Urethane Accelerator may be added up to 4 fl. oz/gal.
94-H2O is aproved for use with any NSF Certified Tnemec topcoat or coating system.
[13] Colors: 00WH Tnemec White, 1211 Red, 1255 Beige, 15BL Tank white, 35GR Black, 39BL Delft
blue, B5712 Westech Blue, 11SF True Blue, B9118 Baker Blue, B8314 Krausz Blue, Y2606
Romac Yellow, B2592 RAL 5009 Azurblau, B7011 Crispin Blue, B2506 Dezurik Blue, A14130
Mueller Gray, B9695 Houston Blue, R5477 Mueller Sienna Red.
Number of Coats: 1
Maximum Field Use Dry Thickness(in mils): 4 mils
Maximum Thinner: 10% No. 4 Thinner by volume
Recoat Cure Time and Temperature: 5 hours at 75°F
Final Cure Time and Temperature: 7 days at 75°F (entire system)
Special Comments: Mix ratio is 1 Part A to 1 Part B by volume. Certified for use as an
optional primer or intermediate coat with any Tnemec NSF certified primer and topcoat
coating system provided the primer, intermediate, and topcoat meet their certified end
uses.
[17] This coating used with Thinner #49 is Certified for use in pipes >= 18". This coating
used with Thinner #2 and Thinner #3 is Certified for use in pipes >=24".
|
||||
|
Coatings - Pump |
||||
| 22 Epoxoline[1] [2] | >= 1/2" | CLD 23 | EPOXY | |
| N140F Pota-Pox Plus Fast Cure[2] [3] | >= 4" | CLD 23 | EPOXY | |
| Series 21 Epoxoline[2] [4] | >= 4” | CLD 23 | EPOXY | |
| Series 91-H2O ™ Hydro-Zinc™ [2] [5] [6] [7] | >= 1/2" | CLD 23 | EPOXY | |
| Series 93-H20 Hydro-Zinc[8] | >= 1/2" | CLD 23 | PUR | |
| Series 94-H2O Hydro-Zinc[2] [9] [18] | >1/2" | CLD 23 | PUR | |
| Series N140 Pota-Pox Plus[14] [15] | >= 4" | CLD 23 | EPOXY | |
| Series N140 Pota-Pox Plus [2] [13] | >= 4" | CLD 23 | EPOXY | |
| Series N140F Pota-Pox Plus Fast Cure[15] [16] | >= 4" | CLD 23 | EPOXY | |
[1] Colors: 1255 Beige, 1218 Blue, WH11 White
Number of Coats: 1-2
Maximum Field Use Dry Film Thickness (in mils): 50
Maximum Thinner: 5% Thinner #2
Recoat Cure Time and Temperature: 16 hours at 75°F
Final Cure Time and Temperature: 5 days at 75°F
Special Comments: Mix ratio of Part A to Part B is 1:1 by volume. Optional use with
fiberglass flake S211-0220. The fiberglass flake can be added up to a rate of 1% by
weight after the Parts A and B are mixed together. Certified for use as a primer or
topcoat with any NSF Certified Tnemec coating system provided that both primer and
topcoat meet their individual certified end uses.
[2] Meets the health effects requirements of NSF/ANSI/CAN 600 according to the requirements
of NSF/ANSI/CAN 61 including the most current health effects criteria for xylenes,
toluene, and ethylbenzene.
[3] Colors: 15BL Tank White, 1255 Beige, 1211 Red, 35GR Black, 39BL Delft Blue, Y2606 Romac
Yellow, 00WH Tnemec White, 11SF True Blue, B9118 Baker Blue, B5712 Westech Blue, B2592
RAL 5009 Azurblau, B9695 Houston Blue, A14130 Mueller Gray, R5477 Mueller Sienna Red.
Number of Coats: 1
Sequence of Coats: 4 mils
Maximum Thinner: 10% No. 4 Thinner by volume
Recoat Cure Time and Temperature: 5 hours at 75F
Final Cure Time/Temperature: 7 days at 75F (entire system)
Special Comments: Mix ration is 1 Part A to 1 Part B by volume. Certified for use as an
optional primer or intermediate topcoat with any Tnemec NSF certified primer and topcoat
coating system provided the primer, intermediate, and topcoat meet their certified end
uses.
[4] Colors: WH16 OFF-WHITE, 35GR Black, 33GR Gray, 39BL Delft Blue, 1255 Beige, B5712
Westech Blue, 11SF True Blue/Safety, 1211 Red Primer, A13096 Baker Dark Gray, B2592
RAL5009 Azurblau, B2506 Dezurik Blue, B9918 New Baker Blue
Number of Coats: 1-3
Maximum Field Use Dry Thickness (in mils): 20
Maximum Thinner: 5% F041-0088 Thinner Clear by volume
Recoat Cure Time and Temperature: 8 hours at 75F
Final Cure Time/Temperature: 7 days at 75F
Special Comments: Mix ratio of A:B is 2:1 by volume. Series 21 Epoxoline is approved for
use as a primer or topcoat with any NSF Certified Tnemec topcoat or coating system
providing that both primer and topcoat meet their individual Certified end uses.
[5] This coating used with Thinner #3 is Certified for use in pipes >=24", tanks >=1500
gallons, fittings >=1/2", pumps >=1/2", valves >=2".
[6] Colors: Greenish-Gray
Number of Coats: 1
Maximum Field Use Dry Thickness (in mils): 4
Maximum Thinner: 10% Thinner #2 or Thinner #3 by volume
Final Cure Time/Temperature: 4 hours at 75F; 2 hours at 75F wen accelerator is used.
Special Comments: Series 44-710 Urethane Accelerator may be added up to 4 fl.oz/gal.
Series 91-H2O Hydro-Zinc ™ is approved for use with any NSF Certified Tnemec topcoat or
coatings system providing that both primer and topcoat meet their individual Certified
end uses. Mix Ratio Part A:B is 70%:30% by volume.
[7] This coating used with Thinner #2 is Certified for use in pipes >=24", tanks >=3000
gallons, fittings >=1", pumps >=1/2", and valves >=4".
[8] Colors: Greenish-Gray
Maximum Field Use Dry Thickness(in mils): 4 mils
Maximum Thinner: 10% Thinner #2 by volume
Final Cure Time/Temperature: 8 hours at 75F. 4 hours at 75F if accelerator is used.
Special Comments: Series 44-710 accelerator may be used up to 4 fluid oz/gal. 93-H20
Hydro-Zinc is approved for use with any NSF Certified Tnemec topcoat or coating system
providing that both primer and topcoat meet their individual Certified end uses.
[9] Colors: Greenish-gray
Number of Coats: 1
Maximum Field Use Dry Film Thickness (in mils): 4
Maximum Thinner: 15% Tnemec No. 49 or 10% Thinner No. 2 or 10% Thinner No. 3 by volume
Final Cure Time and Temperature: 8 hours at 75°F; 2 hours at 75°F when the accelerator
is used
Special Comments: Series 44-710 Urethane Accelerator may be added up to 4 fl. oz/gal.
94-H2O is aproved for use with any NSF Certified Tnemec topcoat or coating system.
[13] Colors: 00WH Tnemec White, 1211 Red, 1255 Beige, 15BL Tank white, 35GR Black, 39BL Delft
blue, B5712 Westech Blue, 11SF True Blue, B9118 Baker Blue, B8314 Krausz Blue, Y2606
Romac Yellow, B2592 RAL 5009 Azurblau, B7011 Crispin Blue, B2506 Dezurik Blue, A14130
Mueller Gray, B9695 Houston Blue, R5477 Mueller Sienna Red.
Number of Coats: 1
Maximum Field Use Dry Thickness(in mils): 4 mils
Maximum Thinner: 10% No. 4 Thinner by volume
Recoat Cure Time and Temperature: 5 hours at 75°F
Final Cure Time and Temperature: 7 days at 75°F (entire system)
Special Comments: Mix ratio is 1 Part A to 1 Part B by volume. Certified for use as an
optional primer or intermediate coat with any Tnemec NSF certified primer and topcoat
coating system provided the primer, intermediate, and topcoat meet their certified end
uses.
[14] Colors: 00WH Tnemec White, 1211 Red, 1255 Beige, 15BL Tank White, 35GR Black, 39BL Delft
Blue, B5712 Westech Blue, 11SF True Blue, B9118 Baker Blue, B8314 Krausz Blue, A13096
Baker Dark Gray, Y2606 Romac Yellow, B2592 RAL 5009 Azurblau, B7011 Crispin Blue, B2506
Dezurik Blue, A14130 Mueller Gray, B9695 Houston Blue, R5477 Mueller Sienna Red.
Number of Coats: 2-3
Sequence of Coats: Any combination of Listed colors
Maximum Field Use Dry Film Thickness (in mils): 18
Maximum Thinner: 5% Tnemec No. 60 Thinner by volume
Recoat Cure Time and Temperature: 5 hours at 75°F with accelerator, 9 hours at 75°F
without accelerator
Final Cure Time and Temperature: 30 days at 75°F
Special Comments: Any Listed color of Series 22, FC22, or N140, may be substituted as a
primer of topcoat for Series N140 Pota-Pox Plus provided that both primer and topcoat
meet their individual Certified end uses. The mix ratio of Part A:Part B is 1:1 by
volume. Part C (Series 44-700 Accelerator) is an optional additive to Part A in the
field and may be added at up to 4 fluid ounces per 2 mixed gallons of parts A and B.
[15] Meets the health effects requirements of NSF/ANSI/CAN 600 according to requirements of
NSF/ANSI/CAN 61 for pump, valve, and fitting end use.
[16] Colors: 00WH Tnemec White, 1211 Red, 1255 Beige, 15BL Tank white, 35GR Black, 39BL Delft
Blue, B2506 DeZurik Blue, B5712 Westech Blue, 11SF True Blue, B9118 Baker Blue, B7896
S-B Blue, Y2606 Romac Yellow, B2592 RAL 5009 Azurblau, B7011 Crispin Blue, B9695 Houston
Blue, A14130 Mueller Gray, R5477 Mueller Sienna Red.
Number of Coats: 2-3
Sequence of Coats: Any combination of Listed colors
Maximum Field Use Dry film Thickness (in mils): 18
Maximum Thinner: 5% Tnemec No. 60 Thinner by volume
Recoat Cure Time and Temperature: 5 hours at 75°F
Final Cure Time and Temperature: 30 days at 75°F
Special Comments: Any listed color of series 22, FC22, or N140 may be substituted as a
primer or topcoat for the Series N140 Pota-Pox Plus provided that both primer and
topcoat meet their individual Certified end uses. Mix ratio of Part A:Part B is 1:1 by
volume.
[18] This coating used with Thinner #49, Thinner #2 and Thinner #3 is Certified for use in
pumps >= 1/2".
|
||||
|
Coatings - Tank |
||||
| 22 Epoxoline[1] [2] | >= 50 gal. | CLD 23 | EPOXY | |
| N140F Pota-Pox Plus Fast Cure [2] [3] | >= 1,500 gal. | CLD 23 | EPOXY | |
| Series 21 Epoxoline [2] [4] | >= 90,000 gal. | CLD 23 | EPOXY | |
| Series 406 Elastoshield[2] [19] | >= 50,000 gal. | CLD 23 | PUR | |
| Series 91-H2O ™ Hydro-Zinc™ [2] [5] [6] | >= 1500 gal. | CLD 23 | EPOXY | |
| Series 91-H2O ™ Hydro-Zinc™ [2] [6] [7] | >= 3000 gal. | CLD 23 | EPOXY | |
| Series 93-H20 Hydro-Zinc[8] | >= 3,000 gal | CLD 23 | PUR | |
| Series 94-H2O Hydro Zinc[2] [9] | [20] | CLD 23 | PUR | |
| Series L140 Pota-Pox Plus [2] [12] | >= 50,000 gal. | CLD 23 | EPOXY | |
| Series L140F Pota-Pox Plus Fast Cure [2] [12] | >= 50,000 gal. | CLD 23 | EPOXY | |
| Series N140 Pota-Pox Plus [2] [13] | >= 1,500 gal. | CLD 23 | EPOXY | |
[1] Colors: 1255 Beige, 1218 Blue, WH11 White
Number of Coats: 1-2
Maximum Field Use Dry Film Thickness (in mils): 50
Maximum Thinner: 5% Thinner #2
Recoat Cure Time and Temperature: 16 hours at 75°F
Final Cure Time and Temperature: 5 days at 75°F
Special Comments: Mix ratio of Part A to Part B is 1:1 by volume. Optional use with
fiberglass flake S211-0220. The fiberglass flake can be added up to a rate of 1% by
weight after the Parts A and B are mixed together. Certified for use as a primer or
topcoat with any NSF Certified Tnemec coating system provided that both primer and
topcoat meet their individual certified end uses.
[2] Meets the health effects requirements of NSF/ANSI/CAN 600 according to the requirements
of NSF/ANSI/CAN 61 including the most current health effects criteria for xylenes,
toluene, and ethylbenzene.
[3] Colors: 15BL Tank White, 1255 Beige, 1211 Red, 35GR Black, 39BL Delft Blue, Y2606 Romac
Yellow, 00WH Tnemec White, 11SF True Blue, B9118 Baker Blue, B5712 Westech Blue, B2592
RAL 5009 Azurblau, B9695 Houston Blue, A14130 Mueller Gray, R5477 Mueller Sienna Red.
Number of Coats: 1
Sequence of Coats: 4 mils
Maximum Thinner: 10% No. 4 Thinner by volume
Recoat Cure Time and Temperature: 5 hours at 75F
Final Cure Time/Temperature: 7 days at 75F (entire system)
Special Comments: Mix ration is 1 Part A to 1 Part B by volume. Certified for use as an
optional primer or intermediate topcoat with any Tnemec NSF certified primer and topcoat
coating system provided the primer, intermediate, and topcoat meet their certified end
uses.
[4] Colors: WH16 OFF-WHITE, 35GR Black, 33GR Gray, 39BL Delft Blue, 1255 Beige, B5712
Westech Blue, 11SF True Blue/Safety, 1211 Red Primer, A13096 Baker Dark Gray, B2592
RAL5009 Azurblau, B2506 Dezurik Blue, B9918 New Baker Blue
Number of Coats: 1-3
Maximum Field Use Dry Thickness (in mils): 20
Maximum Thinner: 5% F041-0088 Thinner Clear by volume
Recoat Cure Time and Temperature: 8 hours at 75F
Final Cure Time/Temperature: 7 days at 75F
Special Comments: Mix ratio of A:B is 2:1 by volume. Series 21 Epoxoline is approved for
use as a primer or topcoat with any NSF Certified Tnemec topcoat or coating system
providing that both primer and topcoat meet their individual Certified end uses.
[5] This coating used with Thinner #3 is Certified for use in pipes >=24", tanks >=1500
gallons, fittings >=1/2", pumps >=1/2", valves >=2".
[6] Colors: Greenish-Gray
Number of Coats: 1
Maximum Field Use Dry Thickness (in mils): 4
Maximum Thinner: 10% Thinner #2 or Thinner #3 by volume
Final Cure Time/Temperature: 4 hours at 75F; 2 hours at 75F wen accelerator is used.
Special Comments: Series 44-710 Urethane Accelerator may be added up to 4 fl.oz/gal.
Series 91-H2O Hydro-Zinc ™ is approved for use with any NSF Certified Tnemec topcoat or
coatings system providing that both primer and topcoat meet their individual Certified
end uses. Mix Ratio Part A:B is 70%:30% by volume.
[7] This coating used with Thinner #2 is Certified for use in pipes >=24", tanks >=3000
gallons, fittings >=1", pumps >=1/2", and valves >=4".
[8] Colors: Greenish-Gray
Maximum Field Use Dry Thickness(in mils): 4 mils
Maximum Thinner: 10% Thinner #2 by volume
Final Cure Time/Temperature: 8 hours at 75F. 4 hours at 75F if accelerator is used.
Special Comments: Series 44-710 accelerator may be used up to 4 fluid oz/gal. 93-H20
Hydro-Zinc is approved for use with any NSF Certified Tnemec topcoat or coating system
providing that both primer and topcoat meet their individual Certified end uses.
[9] Colors: Greenish-gray
Number of Coats: 1
Maximum Field Use Dry Film Thickness (in mils): 4
Maximum Thinner: 15% Tnemec No. 49 or 10% Thinner No. 2 or 10% Thinner No. 3 by volume
Final Cure Time and Temperature: 8 hours at 75°F; 2 hours at 75°F when the accelerator
is used
Special Comments: Series 44-710 Urethane Accelerator may be added up to 4 fl. oz/gal.
94-H2O is aproved for use with any NSF Certified Tnemec topcoat or coating system.
[12] Colors: 1255 Beige, 15BL Tank White, 1211 Red, 00WH White
# of coats: 2-3
# Seq Of Coats: Any combination of listed colors
Max Film Thickness: 18 (Maximum of 6 mils per coat)
Max Thinner: 5% Tnemec No. 49 Thinner by volume
Recoat Cure Time/ Temp.: 16 hours at 75° F
Final Cure Time/ Temp.: 7 days at 75° F
Special Comments: Series N140, N140F, V140, V140F, L140 and Series 22, FC22 may be
substituted as a primer or topcoat for L140F provided that both primer and topcoat meet
their individual Certified end uses. Mix ratio of Part A to Part B is 1:1 by volume.
[13] Colors: 00WH Tnemec White, 1211 Red, 1255 Beige, 15BL Tank white, 35GR Black, 39BL Delft
blue, B5712 Westech Blue, 11SF True Blue, B9118 Baker Blue, B8314 Krausz Blue, Y2606
Romac Yellow, B2592 RAL 5009 Azurblau, B7011 Crispin Blue, B2506 Dezurik Blue, A14130
Mueller Gray, B9695 Houston Blue, R5477 Mueller Sienna Red.
Number of Coats: 1
Maximum Field Use Dry Thickness(in mils): 4 mils
Maximum Thinner: 10% No. 4 Thinner by volume
Recoat Cure Time and Temperature: 5 hours at 75°F
Final Cure Time and Temperature: 7 days at 75°F (entire system)
Special Comments: Mix ratio is 1 Part A to 1 Part B by volume. Certified for use as an
optional primer or intermediate coat with any Tnemec NSF certified primer and topcoat
coating system provided the primer, intermediate, and topcoat meet their certified end
uses.
[19] Colors: WH06 Off-White
Number of Coats: 1-2
Sequence of Coats: Primer (optional), Series 406 Elastoshield (topcoat)
Maximum Field Use Dry Film Thickness (in mils): Topcoat-75
Recoat Cure Time and Temperature: 5 hours at 75°F
Final Cure Time and Temperature: 72 hours at 75°F
Special Comments: Mix ratio for primers must meet their individual certified parameters.
Mix ratio of A:B is 1:2 by volume for Topcoat. Certified for use as a topcoat with any
Tnemec NSF Certified coating system provided both primer and topcoat meet their
individual certified end uses.
[20] This coating used with Thinner #49 is Certified for use in tanks >= 400 gallons. This
coating used with Thinner #2 is Certified for use in tank >=3000 gallons. This coating
used with Thinner #3 is Certified for use in tanks >=1500 gallons.
|
||||
|
Coatings - Valve |
||||
| 22 Epoxoline[1] [2] | >= 1/2" | CLD 23 | EPOXY | |
| N140F Pota-Pox Plus Fast Cure[2] [3] | >= 4" | CLD 23 | EPOXY | |
| Series 21 Epoxoline[2] [4] | >= 4" | CLD 23 | EPOXY | |
| Series 406 Elastoshield[2] [19] | >= 4" | CLD 23 | PUR | |
| Series 91-H2O ™ Hydro-Zinc™ [2] [5] [6] | >= 2" | CLD 23 | EPOXY | |
| Series 91-H2O™ Hydro-Zinc™ [2] [6] [7] | >= 4" | CLD 23 | EPOXY | |
| Series 93-H20 Hydro-Zinc[8] | >= 4" | CLD 23 | PUR | |
| Series 94-H2O Hydro-Zinc[2] [9] | [21] | CLD 23 | PUR | |
| Series N140 Pota-Pox Plus[14] [15] | >= 4" | CLD 23 | EPOXY | |
| Series N140 Pota-Pox Plus [2] [13] | >= 4" | CLD 23 | EPOXY | |
| Series N140F Pota-Pox Plus Fast Cure[15] [16] | >= 4" | CLD 23 | EPOXY | |
[1] Colors: 1255 Beige, 1218 Blue, WH11 White
Number of Coats: 1-2
Maximum Field Use Dry Film Thickness (in mils): 50
Maximum Thinner: 5% Thinner #2
Recoat Cure Time and Temperature: 16 hours at 75°F
Final Cure Time and Temperature: 5 days at 75°F
Special Comments: Mix ratio of Part A to Part B is 1:1 by volume. Optional use with
fiberglass flake S211-0220. The fiberglass flake can be added up to a rate of 1% by
weight after the Parts A and B are mixed together. Certified for use as a primer or
topcoat with any NSF Certified Tnemec coating system provided that both primer and
topcoat meet their individual certified end uses.
[2] Meets the health effects requirements of NSF/ANSI/CAN 600 according to the requirements
of NSF/ANSI/CAN 61 including the most current health effects criteria for xylenes,
toluene, and ethylbenzene.
[3] Colors: 15BL Tank White, 1255 Beige, 1211 Red, 35GR Black, 39BL Delft Blue, Y2606 Romac
Yellow, 00WH Tnemec White, 11SF True Blue, B9118 Baker Blue, B5712 Westech Blue, B2592
RAL 5009 Azurblau, B9695 Houston Blue, A14130 Mueller Gray, R5477 Mueller Sienna Red.
Number of Coats: 1
Sequence of Coats: 4 mils
Maximum Thinner: 10% No. 4 Thinner by volume
Recoat Cure Time and Temperature: 5 hours at 75F
Final Cure Time/Temperature: 7 days at 75F (entire system)
Special Comments: Mix ration is 1 Part A to 1 Part B by volume. Certified for use as an
optional primer or intermediate topcoat with any Tnemec NSF certified primer and topcoat
coating system provided the primer, intermediate, and topcoat meet their certified end
uses.
[4] Colors: WH16 OFF-WHITE, 35GR Black, 33GR Gray, 39BL Delft Blue, 1255 Beige, B5712
Westech Blue, 11SF True Blue/Safety, 1211 Red Primer, A13096 Baker Dark Gray, B2592
RAL5009 Azurblau, B2506 Dezurik Blue, B9918 New Baker Blue
Number of Coats: 1-3
Maximum Field Use Dry Thickness (in mils): 20
Maximum Thinner: 5% F041-0088 Thinner Clear by volume
Recoat Cure Time and Temperature: 8 hours at 75F
Final Cure Time/Temperature: 7 days at 75F
Special Comments: Mix ratio of A:B is 2:1 by volume. Series 21 Epoxoline is approved for
use as a primer or topcoat with any NSF Certified Tnemec topcoat or coating system
providing that both primer and topcoat meet their individual Certified end uses.
[5] This coating used with Thinner #3 is Certified for use in pipes >=24", tanks >=1500
gallons, fittings >=1/2", pumps >=1/2", valves >=2".
[6] Colors: Greenish-Gray
Number of Coats: 1
Maximum Field Use Dry Thickness (in mils): 4
Maximum Thinner: 10% Thinner #2 or Thinner #3 by volume
Final Cure Time/Temperature: 4 hours at 75F; 2 hours at 75F wen accelerator is used.
Special Comments: Series 44-710 Urethane Accelerator may be added up to 4 fl.oz/gal.
Series 91-H2O Hydro-Zinc ™ is approved for use with any NSF Certified Tnemec topcoat or
coatings system providing that both primer and topcoat meet their individual Certified
end uses. Mix Ratio Part A:B is 70%:30% by volume.
[7] This coating used with Thinner #2 is Certified for use in pipes >=24", tanks >=3000
gallons, fittings >=1", pumps >=1/2", and valves >=4".
[8] Colors: Greenish-Gray
Maximum Field Use Dry Thickness(in mils): 4 mils
Maximum Thinner: 10% Thinner #2 by volume
Final Cure Time/Temperature: 8 hours at 75F. 4 hours at 75F if accelerator is used.
Special Comments: Series 44-710 accelerator may be used up to 4 fluid oz/gal. 93-H20
Hydro-Zinc is approved for use with any NSF Certified Tnemec topcoat or coating system
providing that both primer and topcoat meet their individual Certified end uses.
[9] Colors: Greenish-gray
Number of Coats: 1
Maximum Field Use Dry Film Thickness (in mils): 4
Maximum Thinner: 15% Tnemec No. 49 or 10% Thinner No. 2 or 10% Thinner No. 3 by volume
Final Cure Time and Temperature: 8 hours at 75°F; 2 hours at 75°F when the accelerator
is used
Special Comments: Series 44-710 Urethane Accelerator may be added up to 4 fl. oz/gal.
94-H2O is aproved for use with any NSF Certified Tnemec topcoat or coating system.
[13] Colors: 00WH Tnemec White, 1211 Red, 1255 Beige, 15BL Tank white, 35GR Black, 39BL Delft
blue, B5712 Westech Blue, 11SF True Blue, B9118 Baker Blue, B8314 Krausz Blue, Y2606
Romac Yellow, B2592 RAL 5009 Azurblau, B7011 Crispin Blue, B2506 Dezurik Blue, A14130
Mueller Gray, B9695 Houston Blue, R5477 Mueller Sienna Red.
Number of Coats: 1
Maximum Field Use Dry Thickness(in mils): 4 mils
Maximum Thinner: 10% No. 4 Thinner by volume
Recoat Cure Time and Temperature: 5 hours at 75°F
Final Cure Time and Temperature: 7 days at 75°F (entire system)
Special Comments: Mix ratio is 1 Part A to 1 Part B by volume. Certified for use as an
optional primer or intermediate coat with any Tnemec NSF certified primer and topcoat
coating system provided the primer, intermediate, and topcoat meet their certified end
uses.
[14] Colors: 00WH Tnemec White, 1211 Red, 1255 Beige, 15BL Tank White, 35GR Black, 39BL Delft
Blue, B5712 Westech Blue, 11SF True Blue, B9118 Baker Blue, B8314 Krausz Blue, A13096
Baker Dark Gray, Y2606 Romac Yellow, B2592 RAL 5009 Azurblau, B7011 Crispin Blue, B2506
Dezurik Blue, A14130 Mueller Gray, B9695 Houston Blue, R5477 Mueller Sienna Red.
Number of Coats: 2-3
Sequence of Coats: Any combination of Listed colors
Maximum Field Use Dry Film Thickness (in mils): 18
Maximum Thinner: 5% Tnemec No. 60 Thinner by volume
Recoat Cure Time and Temperature: 5 hours at 75°F with accelerator, 9 hours at 75°F
without accelerator
Final Cure Time and Temperature: 30 days at 75°F
Special Comments: Any Listed color of Series 22, FC22, or N140, may be substituted as a
primer of topcoat for Series N140 Pota-Pox Plus provided that both primer and topcoat
meet their individual Certified end uses. The mix ratio of Part A:Part B is 1:1 by
volume. Part C (Series 44-700 Accelerator) is an optional additive to Part A in the
field and may be added at up to 4 fluid ounces per 2 mixed gallons of parts A and B.
[15] Meets the health effects requirements of NSF/ANSI/CAN 600 according to requirements of
NSF/ANSI/CAN 61 for pump, valve, and fitting end use.
[16] Colors: 00WH Tnemec White, 1211 Red, 1255 Beige, 15BL Tank white, 35GR Black, 39BL Delft
Blue, B2506 DeZurik Blue, B5712 Westech Blue, 11SF True Blue, B9118 Baker Blue, B7896
S-B Blue, Y2606 Romac Yellow, B2592 RAL 5009 Azurblau, B7011 Crispin Blue, B9695 Houston
Blue, A14130 Mueller Gray, R5477 Mueller Sienna Red.
Number of Coats: 2-3
Sequence of Coats: Any combination of Listed colors
Maximum Field Use Dry film Thickness (in mils): 18
Maximum Thinner: 5% Tnemec No. 60 Thinner by volume
Recoat Cure Time and Temperature: 5 hours at 75°F
Final Cure Time and Temperature: 30 days at 75°F
Special Comments: Any listed color of series 22, FC22, or N140 may be substituted as a
primer or topcoat for the Series N140 Pota-Pox Plus provided that both primer and
topcoat meet their individual Certified end uses. Mix ratio of Part A:Part B is 1:1 by
volume.
[19] Colors: WH06 Off-White
Number of Coats: 1-2
Sequence of Coats: Primer (optional), Series 406 Elastoshield (topcoat)
Maximum Field Use Dry Film Thickness (in mils): Topcoat-75
Recoat Cure Time and Temperature: 5 hours at 75°F
Final Cure Time and Temperature: 72 hours at 75°F
Special Comments: Mix ratio for primers must meet their individual certified parameters.
Mix ratio of A:B is 1:2 by volume for Topcoat. Certified for use as a topcoat with any
Tnemec NSF Certified coating system provided both primer and topcoat meet their
individual certified end uses.
[21] This coating used with Thinner #49 is Certified for use in valves >=1/2". This coatings
used with Thinner #2 is Certified for use in valves >= 4". This coating used with
Thinner #3 is Certified for use in valves >= 2".
|
||||
Facility : North Kansas City, MO
Protective (Barrier) Materials
| Water | Water | |||
| Water Contact | Contact | Contact | ||
| Trade Designation | Size Restriction | Temp | Material | |
|
Coatings - Fittings |
||||
| 22 Epoxoline[1] [2] | >= 6" | CLD 23 | EPOXY | |
| F098-0H20 Hydro-Zinc[2] [3] | >= 1" | CLD 23 | EPOXY | |
| N140F Pota-Pox Plus Fast Cure[2] [4] | >= 2" | CLD 23 | EPOXY | |
| Series 1220 Tnemec Epoxy[5] | >= 1/2" | CLD 23 | EPOXY | |
| Series 21 Epoxoline[2] [7] | >= 3/4" | CLD 23 | EPOXY | |
| Series 21 Epoxoline[2] [6] | >= 1/2" | CLD 23 | EPOXY | |
| Series 91-H2O™ Hydro-Zinc™[2] [8] [9] [10] | >= 1" | CLD 23 | PUR | |
| Series 93-H20 Hydro-Zinc[11] | >= 1" | CLD 23 | PUR | |
| Series 94-H2O Hydro-Zinc[2] [12] | [13] | CLD 23 | PUR | |
| Series FC22 Epoxoline[2] [14] | >= 1/2" | CLD 23 | EPOXY | |
| Series L140 Pota-Pox Plus[2] [15] | >= 1" | CLD 23 | EPOXY | |
| Series L140F Pota-Pox Plus Fast Cure[2] [16] | >= 1" | CLD 23 | EPOXY | |
| Series N140 Pota-Pox Plus[18] [22] | >= 4" | CLD 23 | EPOXY | |
| Series N140 Pota-Pox Plus [2] [17] | >= 2" | CLD 23 | EPOXY | |
| Series N140F Pota-Pox Plus Fast Cure[18] [19] | >= 4" | CLD 23 | EPOXY | |
[1] Colors: 1255 Beige, 1218 Blue, WH11 White
Number of Coats: 1-2
Maximum Field Use Dry Film Thickness (in mils): 50
Maximum Thinner: 5% Thinner #2
Recoat Cure Time and Temperature: 16 hours at 75°F
Final Cure Time and Temperature: 5 days at 75°F
Special Comments: Mix ratio of Part A to Part B is 1:1 by volume. Optional use with
fiberglass flake S211-0220. The fiberglass flake can be added up to a rate of 1% by
weight after the Parts A and B are mixed together. Certified for use as a primer or
topcoat with any NSF Certified Tnemec coating system provided that both primer and
topcoat meet their individual certified end uses.
[2] Meets the health effects requirements of NSF/ANSI/CAN 600 according to the requirements
of NSF/ANSI/CAN 61 including the most current health effects criteria for xylenes,
toluene, and ethylbenzene.
[3] Colors: Greenish Gray
Number of Coats: 1
Maximum Field Use Dry Thickness (in mils): 4mils
Maximum Thinner: 25% Water
Recoat Cure Time and Temperature: 5 hours at 75F
Final Cure Time/Temperature: 7 days at 75F
Special Comments: Series 44-780 Accelerator may be added up to 1 fl. oz/gal. Series
98-H2O Hydro-Zinc is approved for use as a primer with any NSF Certified Tnemec topcoat
or coating system providing that both primer and topcoat meet their individual Certified
end uses. Cure for Series 98-H2O Hydro-Zinc primer is 5 hours at 75F. Top-coat is then
applied. Final cure is 7 days. Mix ratio of Part A:B:C is 1.4:0.6:1 by volume.
[4] Colors: 15BL Tank White, 1255 Beige, 1211 Red, 35GR Black, 39BL Delft Blue, Y2606 Romac
Yellow, 00WH Tnemec White, 11SF True Blue, B9118 Baker Blue, B5712 Westech Blue, B2592
RAL 5009 Azurblau, B9695 Houston Blue, A14130 Mueller Gray, R5477 Mueller Sienna Red.
Number of Coats: 1
Sequence of Coats: 4 mils
Maximum Thinner: 10% No. 4 Thinner by volume
Recoat Cure Time and Temperature: 5 hours at 75F
Final Cure Time/Temperature: 7 days at 75F (entire system)
Special Comments: Mix ration is 1 Part A to 1 Part B by volume. Certified for use as an
optional primer or intermediate topcoat with any Tnemec NSF certified primer and topcoat
coating system provided the primer, intermediate, and topcoat meet their certified end
uses.
[5] Colors: White
Number of Coats: 1-3
Maximum Field Use Dry Thickness (in mils): 18 mils
Maximum Thinner: 15% water
Recoat Cure Time and Temperature: 6 hours at 75F
Final Cure Time/Temperature: 7 days at 75F
Special Comments: Series 44-700 Accelerator may be added up to 1 fl. oz./gal. Series
1220 Tnemec Epoxy is approved for use as a primer or topcoat with any NSF Certified
Tnemec topcoat or coating system providing that both primer and topcoat meet their
individual Certified end uses. Mix ratio of Part A:Part B is 2:1 by volume.
[6] Colors: WH16 Off-White, 1255 Beige, 39BL Delft Blue, B5712 Westech Blue, 11SF True
Blue/Safety, 1211 Red Primer, A13096 Baker Dark Gray, B2592 RAL5009 Azurblau, B2506
Dezurik Blue, B9918 New Baker Blue
Number of Coats: 2
Maximum Field Use Dry Thickness(in mils): 20 mils
Maximum Thinner: None
Recoat Cure Time and Temperature: 16 hours at 75F
Final Cure Time/Temperature: 30 days at 75F
Special Comments: Mix ratio of A:B is 2:1 by volume. This is for pipe, fitting, pump and
valve end use.
[7] Colors: WH16 OFF-WHITE, 35GR Black, 33GR Gray, 39BL Delft Blue, 1255 Beige, B5712
Westech Blue, 11SF True Blue/Safety, 1211 Red Primer, A13096 Baker Dark Gray, B2592
RAL5009 Azurblau, B2506 Dezurik Blue, B9918 New Baker Blue
Number of Coats: 1-3
Maximum Field Use Dry Thickness(in mils): 20
Maximum Thinner: 5% F041-0088 Thinner Clear by volume
Recoat Cure Time and Temperature: 8 hours at 75F
Final Cure Time/Temperature: 7 days at 75F
Special Comments: Mix ratio of A:B is 2:1 by volume. Series 21 Epoxoline is approved for
use as a primer or topcoat with any NSF Certified Tnemec topcoat or coating system
providing that both primer and topcoat meet their individual Certified end uses.
[8] Colors: Greenish-gray
Number of Coats: 1
Maximum Field Use Dry Film Thickness (in mils): 4
Maximum Thinner: 10% Thinner No. 2 or 10% Thinner No. 3 by volume
Final Cure Time and Temperature: 4 hours at 75°F; 2 hours at 75°F when the accelerator
is used
Special Comments: Series 44-710 Urethane Accelerator may be added up to 4 fl. oz/gal.
Series 91-H2O™ Hydro-Zinc™ is approved for use with any NSF Certified Tnemec topcoat or
coating system providing that both primer and topcoat meet their individual Certified
end uses. Mix ratio of Part A:Part B is 70%:30% by volume.
[9] This coating used with Thinner #2 is Certified for use in pipes >=96", tanks >=50,000
gallons, fittings >=1", pumps >=1", and valves >=4".
[10] This coatings used with Thinner #3 is Certified for use in pipes >=96", tanks >=40,000
gallons, fittings >=1", pumps >=1/2", and valves >=1.75".
[11] Colors: Greenish-Gray
Maximum Field Use Dry Thickness(in mils): 4 mils
Maximum Thinner: 10% Thinner #2 by volume
Final Cure Time/Temperature: 8 hours at 75F. 4 hours at 75F if accelerator is used.
Special Comments: Series 44-710 accelerator may be used up to 4 fluid oz/gal. 93-H20
Hydro-Zinc is approved for use with any NSF Certified Tnemec topcoat or coating system
providing that both primer and topcoat meet their individual Certified end uses.
[12] Color: Greenish-Gray
Number of Coats: 1
Maximum Field Use Dry Film Thickness (in mils): 4
Maximum Thinner: 15% Tnemec No. 49 by volume or 10% Thinner No. 3 or 10% Thinner No. 2
Recoat Cure Time and Temperature: 8 hours at 75°F; 2 hours at 75°F when the accelerator
is used
Special Comments: Series 44-710 may be added up to 4 fl. oz/gal. 94-H2O is approved for
use with any NSF Certified Tnemec topcoat or coating system.
[13] This coating used with Thinner #49 is Certified for use in fittings >= ½”. This coating
used with Thinner #2 and #3 is Certified for use in fittings >= 1”.
[14] Colors: WH08 White, R4875A Akzo Red, B8869A Epoxoline Blue
Number of Coats: 1
Sequence of Coats: N/A
Maximum Field Use Dry Film Thickness (in mils): 80
Maximum Thinner: None
Final Cure Time and Temperature: 24 hours at 75°F
Special Comments: Mix ratio of Part A:Part B is 1:2 by volume. Any Listed color of
series N140 or N140F may be used as a topcoat or primer for Series FC22 Epoxoline.
[15] Colors: 00WH White, 1211 Red, 1255 Beige, 15BL Tank White
Number of Coats: 2-3
Sequence of Coats: Any combination of Listed colors
Maximum Field Use Dry Film Thickness (in mils): 18 (maximum of 6 mils per coat)
Maximum Thinner: 5% Tnemec No. 49 Thinner by volume
Recoat Cure Time and Temperature: 16 hours at 75°F
Final Cure Time and Temperature: 7 days at 75°F
Special Comments: Series N140, N140F, V140, V140F, L140 and Series 22, FC22 may be
substituted as a primer or topcoat for L140 provided that both primer and topcoat meet
their individual Certified end uses. Series 44-700 accelerator (Part C) may be added up
to 4 fluid ounces per two mixed gallons of L140 Parts A and B. Mix ratio of A:B is 1:1
by volume.
[16] Colors: 1255 Beige, 15BL Tank White, 1211 Red, 00WH White
Number of Coats: 2-3
Sequence of coats: Any combination of Listed colors
Maximum Field Use Dry Film Thickness (in mils): 18 (maximum of 6 mils per coat)
Maximum Thinner: 5% Tnemec No. 49 by volume
Recoat Cure Time and Temperature: 16 hours at 75°F
Final Cure Time and Temperature: 7 days at 75°F
Special Comments: Series N140, N140F, V140, V140F, L140 and Series 22, FC22 may be
substituted as a primer or topcoat for L140F provided that both primer and topcoat meet
their individual Certified end uses. Mix ratio of Part A to Part B is 1:1 by volume.
[17] Colors: 00WH Tnemec White, 1211 Red, 1255 Beige, 15BL Tank white, 35GR Black, 39BL Delft
blue, B5712 Westech Blue, 11SF True Blue, B9118 Baker Blue, B8314 Krausz Blue, Y2606
Romac Yellow, B2592 RAL 5009 Azurblau, B7011 Crispin Blue, B2506 Dezurik Blue, B9695
Houston Blue, A14130 Mueller Gray, R5477 Mueller Sienna Red.
Number of Coats: 1
Maximum Field Use Dry Thickness(in mils): 4 mils
Maximum Thinner: 10% No. 4 Thinner by volume
Recoat Cure Time and Temperature: 5 hours at 75°F
Final Cure Time and Temperature: 7 days at 75°F (entire system)
Special Comments: Mix ratio is 1 Part A to 1 Part B by volume. Certified for use
as an optional primer or intermediate coat with any Tnemec NSF certified primer
and topcoat coating system provided the primer, intermediate, and topcoat meet
their certified end uses. Part C (Series 44-700 Accelerator) is an optional additive to
Part A in the field and may be added at up to 4 fluid ounces per gallon of Part A.
[18] Meets the health effects requirements of NSF/ANSI/CAN 600 according to requirements of
NSF/ANSI/CAN 61 for pump, valve, and fitting end use.
[19] Colors: 00WH Tnemec White, 1211 Red, 1255 Beige, 15BL Tank White, 35GR Black, 39BL Delft
Blue, B2506 DeZurik Blue, B5712 Westech Blue, 11SF True Blue, B9118 Baker Blue, B7896
S-B Blue, Y2606 Romac Yellow, B2592 RAL 5009 Azurblau, B7011 Crispin Blue, B9695 Houston
Blue, A14130 Mueller Gray, R5477 Mueller Sienna Red.
Number of Coats: 2-3
Sequence of Coats: Any combination of Listed colors
Maximum Field Use Dry Film Thickness (in mils): 18
Maximum Thinner: 5% Tnemec No. 60 Thinner by volume
Recoat Cure Time and Temperature: 5 hours at 75°F
Final Cure Time and Temperature: 30 days at 75°F
Special comments: Any listed color of Series 22, FC22, N140 or 141 may be substituted as
a primer of topcoat for Series N140 Pota-Pox Plus provided that both primer and topcoat
meet their individual Certified end uses. The mix ratio of Part A:Part B is 1:1 by
volume.
[22] Colors: 00WH Tnemec White, 1211 Red, 1255 Beige, 15BL Tank White, 35GR Black, 39BL Delft
Blue, B5712 Westech Blue, 11SF True Blue, B9118 Baker Blue, B8314 Krausz Blue, A13096
Baker Dark Gray, Y2606 Romac Yellow, B2592 RAL 5009 Azurblau, B7011 Crispin Blue, B2506
Dezurik Blue, B9695 Houston Blue, A14130 Mueller Gray, R5477 Mueller Sienna Red.
Number of Coats: 2-3
Sequence of Coats: Any combination of Listed colors
Maximum Field Use Dry Film Thickness (in mils): 18
Maximum Thinner: 5% Tnemec No. 60 Thinner by volume
Recoat Cure Time and Temperature: 5 hours at 75°F with accelerator, 9 hours at 75°F
without accelerator
Final Cure Time and Temperature: 30 days at 75°F
Special Comments: Any Listed color of Series 22, FC22, N140, or 141 may be substituted
as a primer of topcoat for Series N140 Pota-Pox Plus provided that both primer and
topcoat meet their individual Certified end uses. The mix ratio of Part A:Part B is 1:1
by volume. Part C (Series 44-700 Accelerator) is an optional addititve to Part A in the
field and may be added at up to 4 fluid ounces per two mixed gallons of parts A and B.
|
||||
|
Coatings - Mechanical Devices |
||||
| 22 Epoxoline [1] [2] | [31] | CLD 23 | EPOXY | |
| Series 21 Epoxoline [2] [7] | [29] | CLD 23 | EPOXY | |
| Series 91-H2O™ Hydro-Zinc™[2] [9] [10] [12] | [30] | CLD 23 | PUR | |
| Series 93-H20 Hydro-Zinc[11] | [33] | CLD 23 | PUR | |
| Series 94-H2O Hydro Zinc [2] [12] | [30] [32] | CLD 23 | PUR | |
| Series N140 Pota-Pox Plus [18] [22] | [28] | CLD 23 | EPOXY | |
| Series N140F Pota-Pox Plus Fast Cure[17] [19] | [28] | CLD 23 | EPOXY | |
[1] Colors: 1255 Beige, 1218 Blue, WH11 White
Number of Coats: 1-2
Maximum Field Use Dry Film Thickness (in mils): 50
Maximum Thinner: 5% Thinner #2
Recoat Cure Time and Temperature: 16 hours at 75°F
Final Cure Time and Temperature: 5 days at 75°F
Special Comments: Mix ratio of Part A to Part B is 1:1 by volume. Optional use with
fiberglass flake S211-0220. The fiberglass flake can be added up to a rate of 1% by
weight after the Parts A and B are mixed together. Certified for use as a primer or
topcoat with any NSF Certified Tnemec coating system provided that both primer and
topcoat meet their individual certified end uses.
[2] Meets the health effects requirements of NSF/ANSI/CAN 600 according to the requirements
of NSF/ANSI/CAN 61 including the most current health effects criteria for xylenes,
toluene, and ethylbenzene.
[7] Colors: WH16 OFF-WHITE, 35GR Black, 33GR Gray, 39BL Delft Blue, 1255 Beige, B5712
Westech Blue, 11SF True Blue/Safety, 1211 Red Primer, A13096 Baker Dark Gray, B2592
RAL5009 Azurblau, B2506 Dezurik Blue, B9918 New Baker Blue
Number of Coats: 1-3
Maximum Field Use Dry Thickness(in mils): 20
Maximum Thinner: 5% F041-0088 Thinner Clear by volume
Recoat Cure Time and Temperature: 8 hours at 75F
Final Cure Time/Temperature: 7 days at 75F
Special Comments: Mix ratio of A:B is 2:1 by volume. Series 21 Epoxoline is approved for
use as a primer or topcoat with any NSF Certified Tnemec topcoat or coating system
providing that both primer and topcoat meet their individual Certified end uses.
[9] This coating used with Thinner #2 is Certified for use in pipes >=96", tanks >=50,000
gallons, fittings >=1", pumps >=1", and valves >=4".
[10] This coatings used with Thinner #3 is Certified for use in pipes >=96", tanks >=40,000
gallons, fittings >=1", pumps >=1/2", and valves >=1.75".
[11] Colors: Greenish-Gray
Maximum Field Use Dry Thickness(in mils): 4 mils
Maximum Thinner: 10% Thinner #2 by volume
Final Cure Time/Temperature: 8 hours at 75F. 4 hours at 75F if accelerator is used.
Special Comments: Series 44-710 accelerator may be used up to 4 fluid oz/gal. 93-H20
Hydro-Zinc is approved for use with any NSF Certified Tnemec topcoat or coating system
providing that both primer and topcoat meet their individual Certified end uses.
[12] Color: Greenish-Gray
Number of Coats: 1
Maximum Field Use Dry Film Thickness (in mils): 4
Maximum Thinner: 15% Tnemec No. 49 by volume or 10% Thinner No. 3 or 10% Thinner No. 2
Recoat Cure Time and Temperature: 8 hours at 75°F; 2 hours at 75°F when the accelerator
is used
Special Comments: Series 44-710 may be added up to 4 fl. oz/gal. 94-H2O is approved for
use with any NSF Certified Tnemec topcoat or coating system.
[17] Colors: 00WH Tnemec White, 1211 Red, 1255 Beige, 15BL Tank white, 35GR Black, 39BL Delft
blue, B5712 Westech Blue, 11SF True Blue, B9118 Baker Blue, B8314 Krausz Blue, Y2606
Romac Yellow, B2592 RAL 5009 Azurblau, B7011 Crispin Blue, B2506 Dezurik Blue, B9695
Houston Blue, A14130 Mueller Gray, R5477 Mueller Sienna Red.
Number of Coats: 1
Maximum Field Use Dry Thickness(in mils): 4 mils
Maximum Thinner: 10% No. 4 Thinner by volume
Recoat Cure Time and Temperature: 5 hours at 75°F
Final Cure Time and Temperature: 7 days at 75°F (entire system)
Special Comments: Mix ratio is 1 Part A to 1 Part B by volume. Certified for use
as an optional primer or intermediate coat with any Tnemec NSF certified primer
and topcoat coating system provided the primer, intermediate, and topcoat meet
their certified end uses. Part C (Series 44-700 Accelerator) is an optional additive to
Part A in the field and may be added at up to 4 fluid ounces per gallon of Part A.
[18] Meets the health effects requirements of NSF/ANSI/CAN 600 according to requirements of
NSF/ANSI/CAN 61 for pump, valve, and fitting end use.
[19] Colors: 00WH Tnemec White, 1211 Red, 1255 Beige, 15BL Tank White, 35GR Black, 39BL Delft
Blue, B2506 DeZurik Blue, B5712 Westech Blue, 11SF True Blue, B9118 Baker Blue, B7896
S-B Blue, Y2606 Romac Yellow, B2592 RAL 5009 Azurblau, B7011 Crispin Blue, B9695 Houston
Blue, A14130 Mueller Gray, R5477 Mueller Sienna Red.
Number of Coats: 2-3
Sequence of Coats: Any combination of Listed colors
Maximum Field Use Dry Film Thickness (in mils): 18
Maximum Thinner: 5% Tnemec No. 60 Thinner by volume
Recoat Cure Time and Temperature: 5 hours at 75°F
Final Cure Time and Temperature: 30 days at 75°F
Special comments: Any listed color of Series 22, FC22, N140 or 141 may be substituted as
a primer of topcoat for Series N140 Pota-Pox Plus provided that both primer and topcoat
meet their individual Certified end uses. The mix ratio of Part A:Part B is 1:1 by
volume.
[22] Colors: 00WH Tnemec White, 1211 Red, 1255 Beige, 15BL Tank White, 35GR Black, 39BL Delft
Blue, B5712 Westech Blue, 11SF True Blue, B9118 Baker Blue, B8314 Krausz Blue, A13096
Baker Dark Gray, Y2606 Romac Yellow, B2592 RAL 5009 Azurblau, B7011 Crispin Blue, B2506
Dezurik Blue, B9695 Houston Blue, A14130 Mueller Gray, R5477 Mueller Sienna Red.
Number of Coats: 2-3
Sequence of Coats: Any combination of Listed colors
Maximum Field Use Dry Film Thickness (in mils): 18
Maximum Thinner: 5% Tnemec No. 60 Thinner by volume
Recoat Cure Time and Temperature: 5 hours at 75°F with accelerator, 9 hours at 75°F
without accelerator
Final Cure Time and Temperature: 30 days at 75°F
Special Comments: Any Listed color of Series 22, FC22, N140, or 141 may be substituted
as a primer of topcoat for Series N140 Pota-Pox Plus provided that both primer and
topcoat meet their individual Certified end uses. The mix ratio of Part A:Part B is 1:1
by volume. Part C (Series 44-700 Accelerator) is an optional addititve to Part A in the
field and may be added at up to 4 fluid ounces per two mixed gallons of parts A and B.
[28] Certified for mechanical device end use (other than pump and valve) for a maximum of 4.6
sq. ft. per gpm.
[29] Certified for mechanical device end use (other than pump and valve) for a maximum of 189
sq. ft. per gpm.
[30] Certified for mechanical device end use (other than pump and valve) for a minimum of 60
sq. ft. per gpm when used with Thinner #2 and 64 sq. ft. per gpm when used with Thinner
#3.
[31] Certified for mechanical device end use (other than pump and valve) for a maximum of 249
sq. ft. per gpm.
[32] This coating used with Thinner #49 is Certified for mechanical device end use (other
than pump and valve) for a maximum of 189 sq. Ft. per gpm.
[33] Certified for mechanical device end use (other than pump and valve) for a maximum of 60
sq. ft per gpm.
|
||||
|
Coatings - Pipe |
||||
| 22 Epoxoline[1] [2] | >= 24" | CLD 23 | EPOXY | |
| F098-0H20 Hydro-Zinc[2] [3] | >= 120" | CLD 23 | EPOXY | |
| N140F Pota-Pox Plus Fast Cure [2] [4] | >= 42" | CLD 23 | EPOXY | |
| Series 1 Omnithane 1216 Greenish-Gray[2] [20] | >= 36" | CLD 23 | PUR | |
| Series 1220 Tnemec Epoxy[2] [5] | >= 6" | CLD 23 | EPOXY | |
| Series 21 Epoxoline[2] [6] | >= 18" | CLD 23 | EPOXY | |
| Series 91-H2O™ Hydro-Zinc™[2] [8] [9] [10] | >= 96" | CLD 23 | PUR | |
| Series 93-H20 Hydro-Zinc [11] | >= 96" | CLD 23 | PUR | |
| Series 94-H2O Hydro-Zinc[2] [12] | [21] | CLD 23 | PUR | |
| Series FC22 Epoxoline[2] [14] | >= 8" | CLD 23 | EPOXY | |
| Series N140 Pota-Pox Plus [2] [17] | >= 42" | CLD 23 | EPOXY | |
[1] Colors: 1255 Beige, 1218 Blue, WH11 White
Number of Coats: 1-2
Maximum Field Use Dry Film Thickness (in mils): 50
Maximum Thinner: 5% Thinner #2
Recoat Cure Time and Temperature: 16 hours at 75°F
Final Cure Time and Temperature: 5 days at 75°F
Special Comments: Mix ratio of Part A to Part B is 1:1 by volume. Optional use with
fiberglass flake S211-0220. The fiberglass flake can be added up to a rate of 1% by
weight after the Parts A and B are mixed together. Certified for use as a primer or
topcoat with any NSF Certified Tnemec coating system provided that both primer and
topcoat meet their individual certified end uses.
[2] Meets the health effects requirements of NSF/ANSI/CAN 600 according to the requirements
of NSF/ANSI/CAN 61 including the most current health effects criteria for xylenes,
toluene, and ethylbenzene.
[3] Colors: Greenish Gray
Number of Coats: 1
Maximum Field Use Dry Thickness (in mils): 4mils
Maximum Thinner: 25% Water
Recoat Cure Time and Temperature: 5 hours at 75F
Final Cure Time/Temperature: 7 days at 75F
Special Comments: Series 44-780 Accelerator may be added up to 1 fl. oz/gal. Series
98-H2O Hydro-Zinc is approved for use as a primer with any NSF Certified Tnemec topcoat
or coating system providing that both primer and topcoat meet their individual Certified
end uses. Cure for Series 98-H2O Hydro-Zinc primer is 5 hours at 75F. Top-coat is then
applied. Final cure is 7 days. Mix ratio of Part A:B:C is 1.4:0.6:1 by volume.
[4] Colors: 15BL Tank White, 1255 Beige, 1211 Red, 35GR Black, 39BL Delft Blue, Y2606 Romac
Yellow, 00WH Tnemec White, 11SF True Blue, B9118 Baker Blue, B5712 Westech Blue, B2592
RAL 5009 Azurblau, B9695 Houston Blue, A14130 Mueller Gray, R5477 Mueller Sienna Red.
Number of Coats: 1
Sequence of Coats: 4 mils
Maximum Thinner: 10% No. 4 Thinner by volume
Recoat Cure Time and Temperature: 5 hours at 75F
Final Cure Time/Temperature: 7 days at 75F (entire system)
Special Comments: Mix ration is 1 Part A to 1 Part B by volume. Certified for use as an
optional primer or intermediate topcoat with any Tnemec NSF certified primer and topcoat
coating system provided the primer, intermediate, and topcoat meet their certified end
uses.
[5] Colors: White
Number of Coats: 1-3
Maximum Field Use Dry Thickness (in mils): 18 mils
Maximum Thinner: 15% water
Recoat Cure Time and Temperature: 6 hours at 75F
Final Cure Time/Temperature: 7 days at 75F
Special Comments: Series 44-700 Accelerator may be added up to 1 fl. oz./gal. Series
1220 Tnemec Epoxy is approved for use as a primer or topcoat with any NSF Certified
Tnemec topcoat or coating system providing that both primer and topcoat meet their
individual Certified end uses. Mix ratio of Part A:Part B is 2:1 by volume.
[6] Colors: WH16 Off-White, 1255 Beige, 39BL Delft Blue, B5712 Westech Blue, 11SF True
Blue/Safety, 1211 Red Primer, A13096 Baker Dark Gray, B2592 RAL5009 Azurblau, B2506
Dezurik Blue, B9918 New Baker Blue
Number of Coats: 2
Maximum Field Use Dry Thickness(in mils): 20 mils
Maximum Thinner: None
Recoat Cure Time and Temperature: 16 hours at 75F
Final Cure Time/Temperature: 30 days at 75F
Special Comments: Mix ratio of A:B is 2:1 by volume. This is for pipe, fitting, pump and
valve end use.
[8] Colors: Greenish-gray
Number of Coats: 1
Maximum Field Use Dry Film Thickness (in mils): 4
Maximum Thinner: 10% Thinner No. 2 or 10% Thinner No. 3 by volume
Final Cure Time and Temperature: 4 hours at 75°F; 2 hours at 75°F when the accelerator
is used
Special Comments: Series 44-710 Urethane Accelerator may be added up to 4 fl. oz/gal.
Series 91-H2O™ Hydro-Zinc™ is approved for use with any NSF Certified Tnemec topcoat or
coating system providing that both primer and topcoat meet their individual Certified
end uses. Mix ratio of Part A:Part B is 70%:30% by volume.
[9] This coating used with Thinner #2 is Certified for use in pipes >=96", tanks >=50,000
gallons, fittings >=1", pumps >=1", and valves >=4".
[10] This coatings used with Thinner #3 is Certified for use in pipes >=96", tanks >=40,000
gallons, fittings >=1", pumps >=1/2", and valves >=1.75".
[11] Colors: Greenish-Gray
Maximum Field Use Dry Thickness(in mils): 4 mils
Maximum Thinner: 10% Thinner #2 by volume
Final Cure Time/Temperature: 8 hours at 75F. 4 hours at 75F if accelerator is used.
Special Comments: Series 44-710 accelerator may be used up to 4 fluid oz/gal. 93-H20
Hydro-Zinc is approved for use with any NSF Certified Tnemec topcoat or coating system
providing that both primer and topcoat meet their individual Certified end uses.
[12] Color: Greenish-Gray
Number of Coats: 1
Maximum Field Use Dry Film Thickness (in mils): 4
Maximum Thinner: 15% Tnemec No. 49 by volume or 10% Thinner No. 3 or 10% Thinner No. 2
Recoat Cure Time and Temperature: 8 hours at 75°F; 2 hours at 75°F when the accelerator
is used
Special Comments: Series 44-710 may be added up to 4 fl. oz/gal. 94-H2O is approved for
use with any NSF Certified Tnemec topcoat or coating system.
[14] Colors: WH08 White, R4875A Akzo Red, B8869A Epoxoline Blue
Number of Coats: 1
Sequence of Coats: N/A
Maximum Field Use Dry Film Thickness (in mils): 80
Maximum Thinner: None
Final Cure Time and Temperature: 24 hours at 75°F
Special Comments: Mix ratio of Part A:Part B is 1:2 by volume. Any Listed color of
series N140 or N140F may be used as a topcoat or primer for Series FC22 Epoxoline.
[17] Colors: 00WH Tnemec White, 1211 Red, 1255 Beige, 15BL Tank white, 35GR Black, 39BL Delft
blue, B5712 Westech Blue, 11SF True Blue, B9118 Baker Blue, B8314 Krausz Blue, Y2606
Romac Yellow, B2592 RAL 5009 Azurblau, B7011 Crispin Blue, B2506 Dezurik Blue, B9695
Houston Blue, A14130 Mueller Gray, R5477 Mueller Sienna Red.
Number of Coats: 1
Maximum Field Use Dry Thickness(in mils): 4 mils
Maximum Thinner: 10% No. 4 Thinner by volume
Recoat Cure Time and Temperature: 5 hours at 75°F
Final Cure Time and Temperature: 7 days at 75°F (entire system)
Special Comments: Mix ratio is 1 Part A to 1 Part B by volume. Certified for use
as an optional primer or intermediate coat with any Tnemec NSF certified primer
and topcoat coating system provided the primer, intermediate, and topcoat meet
their certified end uses. Part C (Series 44-700 Accelerator) is an optional additive to
Part A in the field and may be added at up to 4 fluid ounces per gallon of Part A.
[20] Colors: 1216 Greenish-Gray
Number of Coats: 1
Sequence of Coats: N/A
Maximum Field Use Dry Film Thickness (in mils): 4
Maximum Thinner: 10% Thinner No. 2
Recoat Cure Time and Temperature: 8 hours at 75°F
Special Comment: Series 44-710 may be added up to 4 fl. oz/gal. Approved for use as a
primer with any NSF Certified Tnemec topcoat or coating system provided that both primer
and topcoat meet their individual Certified end uses.
[21] This coating used with Thinner #49 is Certified for use in pipes <= 22”. This coating
used with Thinner #2 and #3 is Certified for use in pipes >= 96”.
|
||||
|
Coatings - Pump |
||||
| 22 Epoxoline[1] [2] | >= 4" | CLD 23 | EPOXY | |
| F098-0H20 Hydro-Zinc[2] [3] | >= 4" | CLD 23 | EPOXY | |
| N140F Pota-Pox Plus Fast Cure[2] [4] | >= 4" | CLD 23 | EPOXY | |
| Series 1220 Tnemec Epoxy[2] [5] | >= 1 1/2" | CLD 23 | EPOXY | |
| Series 21 Epoxoline[2] [7] | >= 4" | CLD 23 | EPOXY | |
| Series 21 Epoxoline[2] [6] | >= 1/2" | CLD 23 | EPOXY | |
| Series 91-H2O ™ Hydro-Zinc™ [2] [8] [10] | >= 1/2" | CLD 23 | PUR | |
| Series 91-H2O™ Hydro-Zinc™[2] [8] [9] | >= 1" | CLD 23 | PUR | |
| Series 93-H20 Hydro-Zinc [11] | >= 1" | CLD 23 | PUR | |
| Series 94-H2O Hydro-Zinc[2] [12] | [23] | CLD 23 | PUR | |
| Series FC22 Epoxoline[2] [14] | >= 2" | CLD 23 | EPOXY | |
| Series N140 Pota-Pox Plus[18] [22] | >= 4" | CLD 23 | EPOXY | |
| Series N140 Pota-Pox Plus[2] [17] | >= 4" | CLD 23 | EPOXY | |
| Series N140F Pota-Pox Plus Fast Cure[18] [19] | >= 4" | CLD 23 | EPOXY | |
[1] Colors: 1255 Beige, 1218 Blue, WH11 White
Number of Coats: 1-2
Maximum Field Use Dry Film Thickness (in mils): 50
Maximum Thinner: 5% Thinner #2
Recoat Cure Time and Temperature: 16 hours at 75°F
Final Cure Time and Temperature: 5 days at 75°F
Special Comments: Mix ratio of Part A to Part B is 1:1 by volume. Optional use with
fiberglass flake S211-0220. The fiberglass flake can be added up to a rate of 1% by
weight after the Parts A and B are mixed together. Certified for use as a primer or
topcoat with any NSF Certified Tnemec coating system provided that both primer and
topcoat meet their individual certified end uses.
[2] Meets the health effects requirements of NSF/ANSI/CAN 600 according to the requirements
of NSF/ANSI/CAN 61 including the most current health effects criteria for xylenes,
toluene, and ethylbenzene.
[3] Colors: Greenish Gray
Number of Coats: 1
Maximum Field Use Dry Thickness (in mils): 4mils
Maximum Thinner: 25% Water
Recoat Cure Time and Temperature: 5 hours at 75F
Final Cure Time/Temperature: 7 days at 75F
Special Comments: Series 44-780 Accelerator may be added up to 1 fl. oz/gal. Series
98-H2O Hydro-Zinc is approved for use as a primer with any NSF Certified Tnemec topcoat
or coating system providing that both primer and topcoat meet their individual Certified
end uses. Cure for Series 98-H2O Hydro-Zinc primer is 5 hours at 75F. Top-coat is then
applied. Final cure is 7 days. Mix ratio of Part A:B:C is 1.4:0.6:1 by volume.
[4] Colors: 15BL Tank White, 1255 Beige, 1211 Red, 35GR Black, 39BL Delft Blue, Y2606 Romac
Yellow, 00WH Tnemec White, 11SF True Blue, B9118 Baker Blue, B5712 Westech Blue, B2592
RAL 5009 Azurblau, B9695 Houston Blue, A14130 Mueller Gray, R5477 Mueller Sienna Red.
Number of Coats: 1
Sequence of Coats: 4 mils
Maximum Thinner: 10% No. 4 Thinner by volume
Recoat Cure Time and Temperature: 5 hours at 75F
Final Cure Time/Temperature: 7 days at 75F (entire system)
Special Comments: Mix ration is 1 Part A to 1 Part B by volume. Certified for use as an
optional primer or intermediate topcoat with any Tnemec NSF certified primer and topcoat
coating system provided the primer, intermediate, and topcoat meet their certified end
uses.
[5] Colors: White
Number of Coats: 1-3
Maximum Field Use Dry Thickness (in mils): 18 mils
Maximum Thinner: 15% water
Recoat Cure Time and Temperature: 6 hours at 75F
Final Cure Time/Temperature: 7 days at 75F
Special Comments: Series 44-700 Accelerator may be added up to 1 fl. oz./gal. Series
1220 Tnemec Epoxy is approved for use as a primer or topcoat with any NSF Certified
Tnemec topcoat or coating system providing that both primer and topcoat meet their
individual Certified end uses. Mix ratio of Part A:Part B is 2:1 by volume.
[6] Colors: WH16 Off-White, 1255 Beige, 39BL Delft Blue, B5712 Westech Blue, 11SF True
Blue/Safety, 1211 Red Primer, A13096 Baker Dark Gray, B2592 RAL5009 Azurblau, B2506
Dezurik Blue, B9918 New Baker Blue
Number of Coats: 2
Maximum Field Use Dry Thickness(in mils): 20 mils
Maximum Thinner: None
Recoat Cure Time and Temperature: 16 hours at 75F
Final Cure Time/Temperature: 30 days at 75F
Special Comments: Mix ratio of A:B is 2:1 by volume. This is for pipe, fitting, pump and
valve end use.
[7] Colors: WH16 OFF-WHITE, 35GR Black, 33GR Gray, 39BL Delft Blue, 1255 Beige, B5712
Westech Blue, 11SF True Blue/Safety, 1211 Red Primer, A13096 Baker Dark Gray, B2592
RAL5009 Azurblau, B2506 Dezurik Blue, B9918 New Baker Blue
Number of Coats: 1-3
Maximum Field Use Dry Thickness(in mils): 20
Maximum Thinner: 5% F041-0088 Thinner Clear by volume
Recoat Cure Time and Temperature: 8 hours at 75F
Final Cure Time/Temperature: 7 days at 75F
Special Comments: Mix ratio of A:B is 2:1 by volume. Series 21 Epoxoline is approved for
use as a primer or topcoat with any NSF Certified Tnemec topcoat or coating system
providing that both primer and topcoat meet their individual Certified end uses.
[8] Colors: Greenish-gray
Number of Coats: 1
Maximum Field Use Dry Film Thickness (in mils): 4
Maximum Thinner: 10% Thinner No. 2 or 10% Thinner No. 3 by volume
Final Cure Time and Temperature: 4 hours at 75°F; 2 hours at 75°F when the accelerator
is used
Special Comments: Series 44-710 Urethane Accelerator may be added up to 4 fl. oz/gal.
Series 91-H2O™ Hydro-Zinc™ is approved for use with any NSF Certified Tnemec topcoat or
coating system providing that both primer and topcoat meet their individual Certified
end uses. Mix ratio of Part A:Part B is 70%:30% by volume.
[9] This coating used with Thinner #2 is Certified for use in pipes >=96", tanks >=50,000
gallons, fittings >=1", pumps >=1", and valves >=4".
[10] This coatings used with Thinner #3 is Certified for use in pipes >=96", tanks >=40,000
gallons, fittings >=1", pumps >=1/2", and valves >=1.75".
[11] Colors: Greenish-Gray
Maximum Field Use Dry Thickness(in mils): 4 mils
Maximum Thinner: 10% Thinner #2 by volume
Final Cure Time/Temperature: 8 hours at 75F. 4 hours at 75F if accelerator is used.
Special Comments: Series 44-710 accelerator may be used up to 4 fluid oz/gal. 93-H20
Hydro-Zinc is approved for use with any NSF Certified Tnemec topcoat or coating system
providing that both primer and topcoat meet their individual Certified end uses.
[12] Color: Greenish-Gray
Number of Coats: 1
Maximum Field Use Dry Film Thickness (in mils): 4
Maximum Thinner: 15% Tnemec No. 49 by volume or 10% Thinner No. 3 or 10% Thinner No. 2
Recoat Cure Time and Temperature: 8 hours at 75°F; 2 hours at 75°F when the accelerator
is used
Special Comments: Series 44-710 may be added up to 4 fl. oz/gal. 94-H2O is approved for
use with any NSF Certified Tnemec topcoat or coating system.
[14] Colors: WH08 White, R4875A Akzo Red, B8869A Epoxoline Blue
Number of Coats: 1
Sequence of Coats: N/A
Maximum Field Use Dry Film Thickness (in mils): 80
Maximum Thinner: None
Final Cure Time and Temperature: 24 hours at 75°F
Special Comments: Mix ratio of Part A:Part B is 1:2 by volume. Any Listed color of
series N140 or N140F may be used as a topcoat or primer for Series FC22 Epoxoline.
[17] Colors: 00WH Tnemec White, 1211 Red, 1255 Beige, 15BL Tank white, 35GR Black, 39BL Delft
blue, B5712 Westech Blue, 11SF True Blue, B9118 Baker Blue, B8314 Krausz Blue, Y2606
Romac Yellow, B2592 RAL 5009 Azurblau, B7011 Crispin Blue, B2506 Dezurik Blue, B9695
Houston Blue, A14130 Mueller Gray, R5477 Mueller Sienna Red.
Number of Coats: 1
Maximum Field Use Dry Thickness(in mils): 4 mils
Maximum Thinner: 10% No. 4 Thinner by volume
Recoat Cure Time and Temperature: 5 hours at 75°F
Final Cure Time and Temperature: 7 days at 75°F (entire system)
Special Comments: Mix ratio is 1 Part A to 1 Part B by volume. Certified for use
as an optional primer or intermediate coat with any Tnemec NSF certified primer
and topcoat coating system provided the primer, intermediate, and topcoat meet
their certified end uses. Part C (Series 44-700 Accelerator) is an optional additive to
Part A in the field and may be added at up to 4 fluid ounces per gallon of Part A.
[18] Meets the health effects requirements of NSF/ANSI/CAN 600 according to requirements of
NSF/ANSI/CAN 61 for pump, valve, and fitting end use.
[19] Colors: 00WH Tnemec White, 1211 Red, 1255 Beige, 15BL Tank White, 35GR Black, 39BL Delft
Blue, B2506 DeZurik Blue, B5712 Westech Blue, 11SF True Blue, B9118 Baker Blue, B7896
S-B Blue, Y2606 Romac Yellow, B2592 RAL 5009 Azurblau, B7011 Crispin Blue, B9695 Houston
Blue, A14130 Mueller Gray, R5477 Mueller Sienna Red.
Number of Coats: 2-3
Sequence of Coats: Any combination of Listed colors
Maximum Field Use Dry Film Thickness (in mils): 18
Maximum Thinner: 5% Tnemec No. 60 Thinner by volume
Recoat Cure Time and Temperature: 5 hours at 75°F
Final Cure Time and Temperature: 30 days at 75°F
Special comments: Any listed color of Series 22, FC22, N140 or 141 may be substituted as
a primer of topcoat for Series N140 Pota-Pox Plus provided that both primer and topcoat
meet their individual Certified end uses. The mix ratio of Part A:Part B is 1:1 by
volume.
[22] Colors: 00WH Tnemec White, 1211 Red, 1255 Beige, 15BL Tank White, 35GR Black, 39BL Delft
Blue, B5712 Westech Blue, 11SF True Blue, B9118 Baker Blue, B8314 Krausz Blue, A13096
Baker Dark Gray, Y2606 Romac Yellow, B2592 RAL 5009 Azurblau, B7011 Crispin Blue, B2506
Dezurik Blue, B9695 Houston Blue, A14130 Mueller Gray, R5477 Mueller Sienna Red.
Number of Coats: 2-3
Sequence of Coats: Any combination of Listed colors
Maximum Field Use Dry Film Thickness (in mils): 18
Maximum Thinner: 5% Tnemec No. 60 Thinner by volume
Recoat Cure Time and Temperature: 5 hours at 75°F with accelerator, 9 hours at 75°F
without accelerator
Final Cure Time and Temperature: 30 days at 75°F
Special Comments: Any Listed color of Series 22, FC22, N140, or 141 may be substituted
as a primer of topcoat for Series N140 Pota-Pox Plus provided that both primer and
topcoat meet their individual Certified end uses. The mix ratio of Part A:Part B is 1:1
by volume. Part C (Series 44-700 Accelerator) is an optional addititve to Part A in the
field and may be added at up to 4 fluid ounces per two mixed gallons of parts A and B.
[23] This coating used with Thinner #49 is Certified for use in pumps >= ¾”. This coating
used with Thinner #2 is Certified for use in pumps >= 1”. This coating used with Thinner
#3 is Certified for use in pumps >= ½”.
|
||||
|
Coatings - Tank |
||||
| 22 Epoxoline[1] [2] | >= 700 gal. | CLD 23 | EPOXY | |
| F098-0H20 Hydro-Zinc[2] [3] | >= 70,000 gal. | CLD 23 | EPOXY | |
| N140F Pota-Pox Plus Fast Cure[2] [4] | >= 4,000 gal. | CLD 23 | EPOXY | |
| Series 1 Omnithane 1216 Greenish-Gray[2] [20] | >= 1000 gal. | CLD 23 | PUR | |
| Series 1220 Tnemec Epoxy[2] [5] | >= 200 gal. | CLD 23 | EPOXY | |
| Series 21 Epoxoline[2] [7] | >= 1,500 gal. | CLD 23 | EPOXY | |
| Series 215[2] [24] | >= 200 gal. | CLD 23 | EPOXY | |
| Series 215ML[2] [24] | >= 200 gal. | CLD 23 | EPOXY | |
| Series 91-H2O ™ Hydro-Zinc™ [2] [8] [10] | >= 40,000 gal. | CLD 23 | PUR | |
| Series 91-H2O™ Hydro-Zinc™[2] [8] [9] | >= 50,000 gal. | CLD 23 | PUR | |
| Series 93-H20 Hydro-Zinc [11] | >= 50,000 gal | CLD 23 | PUR | |
| Series 94-H2O Hydro Zinc[2] [12] | [25] | CLD 23 | PUR | |
| Series FC22 Epoxoline[2] [26] | >= 200 gal. | CLD 23 | EPOXY | |
| Series L140 Pota-Pox Plus[2] [15] | >= 50,000 gal. | CLD 23 | EPOXY | |
| Series L140F Pota-Pox Plus Fast Cure[2] [16] | >= 50,000 gal. | CLD 23 | EPOXY | |
| Series N140 Pota-Pox Plus[2] [17] | >= 4,000 gal. | CLD 23 | EPOXY | |
[1] Colors: 1255 Beige, 1218 Blue, WH11 White
Number of Coats: 1-2
Maximum Field Use Dry Film Thickness (in mils): 50
Maximum Thinner: 5% Thinner #2
Recoat Cure Time and Temperature: 16 hours at 75°F
Final Cure Time and Temperature: 5 days at 75°F
Special Comments: Mix ratio of Part A to Part B is 1:1 by volume. Optional use with
fiberglass flake S211-0220. The fiberglass flake can be added up to a rate of 1% by
weight after the Parts A and B are mixed together. Certified for use as a primer or
topcoat with any NSF Certified Tnemec coating system provided that both primer and
topcoat meet their individual certified end uses.
[2] Meets the health effects requirements of NSF/ANSI/CAN 600 according to the requirements
of NSF/ANSI/CAN 61 including the most current health effects criteria for xylenes,
toluene, and ethylbenzene.
[3] Colors: Greenish Gray
Number of Coats: 1
Maximum Field Use Dry Thickness (in mils): 4mils
Maximum Thinner: 25% Water
Recoat Cure Time and Temperature: 5 hours at 75F
Final Cure Time/Temperature: 7 days at 75F
Special Comments: Series 44-780 Accelerator may be added up to 1 fl. oz/gal. Series
98-H2O Hydro-Zinc is approved for use as a primer with any NSF Certified Tnemec topcoat
or coating system providing that both primer and topcoat meet their individual Certified
end uses. Cure for Series 98-H2O Hydro-Zinc primer is 5 hours at 75F. Top-coat is then
applied. Final cure is 7 days. Mix ratio of Part A:B:C is 1.4:0.6:1 by volume.
[4] Colors: 15BL Tank White, 1255 Beige, 1211 Red, 35GR Black, 39BL Delft Blue, Y2606 Romac
Yellow, 00WH Tnemec White, 11SF True Blue, B9118 Baker Blue, B5712 Westech Blue, B2592
RAL 5009 Azurblau, B9695 Houston Blue, A14130 Mueller Gray, R5477 Mueller Sienna Red.
Number of Coats: 1
Sequence of Coats: 4 mils
Maximum Thinner: 10% No. 4 Thinner by volume
Recoat Cure Time and Temperature: 5 hours at 75F
Final Cure Time/Temperature: 7 days at 75F (entire system)
Special Comments: Mix ration is 1 Part A to 1 Part B by volume. Certified for use as an
optional primer or intermediate topcoat with any Tnemec NSF certified primer and topcoat
coating system provided the primer, intermediate, and topcoat meet their certified end
uses.
[5] Colors: White
Number of Coats: 1-3
Maximum Field Use Dry Thickness (in mils): 18 mils
Maximum Thinner: 15% water
Recoat Cure Time and Temperature: 6 hours at 75F
Final Cure Time/Temperature: 7 days at 75F
Special Comments: Series 44-700 Accelerator may be added up to 1 fl. oz./gal. Series
1220 Tnemec Epoxy is approved for use as a primer or topcoat with any NSF Certified
Tnemec topcoat or coating system providing that both primer and topcoat meet their
individual Certified end uses. Mix ratio of Part A:Part B is 2:1 by volume.
[7] Colors: WH16 OFF-WHITE, 35GR Black, 33GR Gray, 39BL Delft Blue, 1255 Beige, B5712
Westech Blue, 11SF True Blue/Safety, 1211 Red Primer, A13096 Baker Dark Gray, B2592
RAL5009 Azurblau, B2506 Dezurik Blue, B9918 New Baker Blue
Number of Coats: 1-3
Maximum Field Use Dry Thickness(in mils): 20
Maximum Thinner: 5% F041-0088 Thinner Clear by volume
Recoat Cure Time and Temperature: 8 hours at 75F
Final Cure Time/Temperature: 7 days at 75F
Special Comments: Mix ratio of A:B is 2:1 by volume. Series 21 Epoxoline is approved for
use as a primer or topcoat with any NSF Certified Tnemec topcoat or coating system
providing that both primer and topcoat meet their individual Certified end uses.
[8] Colors: Greenish-gray
Number of Coats: 1
Maximum Field Use Dry Film Thickness (in mils): 4
Maximum Thinner: 10% Thinner No. 2 or 10% Thinner No. 3 by volume
Final Cure Time and Temperature: 4 hours at 75°F; 2 hours at 75°F when the accelerator
is used
Special Comments: Series 44-710 Urethane Accelerator may be added up to 4 fl. oz/gal.
Series 91-H2O™ Hydro-Zinc™ is approved for use with any NSF Certified Tnemec topcoat or
coating system providing that both primer and topcoat meet their individual Certified
end uses. Mix ratio of Part A:Part B is 70%:30% by volume.
[9] This coating used with Thinner #2 is Certified for use in pipes >=96", tanks >=50,000
gallons, fittings >=1", pumps >=1", and valves >=4".
[10] This coatings used with Thinner #3 is Certified for use in pipes >=96", tanks >=40,000
gallons, fittings >=1", pumps >=1/2", and valves >=1.75".
[11] Colors: Greenish-Gray
Maximum Field Use Dry Thickness(in mils): 4 mils
Maximum Thinner: 10% Thinner #2 by volume
Final Cure Time/Temperature: 8 hours at 75F. 4 hours at 75F if accelerator is used.
Special Comments: Series 44-710 accelerator may be used up to 4 fluid oz/gal. 93-H20
Hydro-Zinc is approved for use with any NSF Certified Tnemec topcoat or coating system
providing that both primer and topcoat meet their individual Certified end uses.
[12] Color: Greenish-Gray
Number of Coats: 1
Maximum Field Use Dry Film Thickness (in mils): 4
Maximum Thinner: 15% Tnemec No. 49 by volume or 10% Thinner No. 3 or 10% Thinner No. 2
Recoat Cure Time and Temperature: 8 hours at 75°F; 2 hours at 75°F when the accelerator
is used
Special Comments: Series 44-710 may be added up to 4 fl. oz/gal. 94-H2O is approved for
use with any NSF Certified Tnemec topcoat or coating system.
[15] Colors: 00WH White, 1211 Red, 1255 Beige, 15BL Tank White
Number of Coats: 2-3
Sequence of Coats: Any combination of Listed colors
Maximum Field Use Dry Film Thickness (in mils): 18 (maximum of 6 mils per coat)
Maximum Thinner: 5% Tnemec No. 49 Thinner by volume
Recoat Cure Time and Temperature: 16 hours at 75°F
Final Cure Time and Temperature: 7 days at 75°F
Special Comments: Series N140, N140F, V140, V140F, L140 and Series 22, FC22 may be
substituted as a primer or topcoat for L140 provided that both primer and topcoat meet
their individual Certified end uses. Series 44-700 accelerator (Part C) may be added up
to 4 fluid ounces per two mixed gallons of L140 Parts A and B. Mix ratio of A:B is 1:1
by volume.
[16] Colors: 1255 Beige, 15BL Tank White, 1211 Red, 00WH White
Number of Coats: 2-3
Sequence of coats: Any combination of Listed colors
Maximum Field Use Dry Film Thickness (in mils): 18 (maximum of 6 mils per coat)
Maximum Thinner: 5% Tnemec No. 49 by volume
Recoat Cure Time and Temperature: 16 hours at 75°F
Final Cure Time and Temperature: 7 days at 75°F
Special Comments: Series N140, N140F, V140, V140F, L140 and Series 22, FC22 may be
substituted as a primer or topcoat for L140F provided that both primer and topcoat meet
their individual Certified end uses. Mix ratio of Part A to Part B is 1:1 by volume.
[17] Colors: 00WH Tnemec White, 1211 Red, 1255 Beige, 15BL Tank white, 35GR Black, 39BL Delft
blue, B5712 Westech Blue, 11SF True Blue, B9118 Baker Blue, B8314 Krausz Blue, Y2606
Romac Yellow, B2592 RAL 5009 Azurblau, B7011 Crispin Blue, B2506 Dezurik Blue, B9695
Houston Blue, A14130 Mueller Gray, R5477 Mueller Sienna Red.
Number of Coats: 1
Maximum Field Use Dry Thickness(in mils): 4 mils
Maximum Thinner: 10% No. 4 Thinner by volume
Recoat Cure Time and Temperature: 5 hours at 75°F
Final Cure Time and Temperature: 7 days at 75°F (entire system)
Special Comments: Mix ratio is 1 Part A to 1 Part B by volume. Certified for use
as an optional primer or intermediate coat with any Tnemec NSF certified primer
and topcoat coating system provided the primer, intermediate, and topcoat meet
their certified end uses. Part C (Series 44-700 Accelerator) is an optional additive to
Part A in the field and may be added at up to 4 fluid ounces per gallon of Part A.
[20] Colors: 1216 Greenish-Gray
Number of Coats: 1
Sequence of Coats: N/A
Maximum Field Use Dry Film Thickness (in mils): 4
Maximum Thinner: 10% Thinner No. 2
Recoat Cure Time and Temperature: 8 hours at 75°F
Special Comment: Series 44-710 may be added up to 4 fl. oz/gal. Approved for use as a
primer with any NSF Certified Tnemec topcoat or coating system provided that both primer
and topcoat meet their individual Certified end uses.
[24] Colors: 1200 White, 1212 Gray
Number of Coats: 1
Maximum Field Use Dry Film Thickness (in mils): Coating only: 80; With fiberglass mat:
95
Final Cure Time and Temperature: 7 days at 75°F
Special Comments: Mix ratio of Part A to Part B is 1:1 by volume. Optional use with
fiberglass mat S211-0215, S211-0216, and/or addition of fumed silica S211-0211 to
coating. Mix ratio for fumed silica is 0.75:1 by volume. Approved for use with any NSF
Certified Tnemec topcoat or coating system provided that both primer and topcoat meet
their individual Certified end uses.
[25] This coating used with Thinner #49 is Certified for use in tanks >= 1,500 gallons. This
coating used with Thinner #2 is Certified for use in tanks >= 50,000 gallons. This
coating used with Thinner #3 is Certified for use in tanks >= 40,000 gallons.
[26] Colors: WH08 White, 35GR Epoxoline Black, R4875A Akzo Red, B8869A Epoxoline Blue
Number of Coats: 1
Sequence of Coats: N/A
Maximum Field Use Dry Film Thickness (in mils): 80
Maximum Thinner: None
Final Cure Time and Temperature: 24 hours at 75° F
Special Comments: Mix ratio of part A:Part B is 1:2 by volume. Any Listed color of
Series F020, FC20, L140, L140F, N140, N140F, V140, or V140F may be used as a topcoat or
primer for SeriesFC22 Epoxoline.
|
||||
|
Coatings - Valve |
||||
| 22 Epoxoline[1] [2] | >= 4" | CLD 23 | EPOXY | |
| F098-0H20 Hydro-Zinc[2] [3] | >= 4" | CLD 23 | EPOXY | |
| N140F Pota-Pox Plus Fast Cure[2] [4] | >= 4" | CLD 23 | EPOXY | |
| Series 1 Omnithane 1216 Greenish-Gray[2] [20] | >= 4" | CLD 23 | PUR | |
| Series 1220 Tnemec Epoxy[2] [5] | >= 1 1/2" | CLD 23 | EPOXY | |
| Series 21 Epoxoline[2] [7] | >= 4" | CLD 23 | EPOXY | |
| Series 21 Epoxoline [2] [6] | >= 1/2" | CLD 23 | EPOXY | |
| Series 91-H2O ™ Hydro-Zinc™[2] [8] [10] | >= 1 3/4" | CLD 23 | EPOXY | |
| Series 91-H2O™ Hydro-Zinc™[2] [8] [9] | >= 4" | CLD 23 | PUR | |
| Series 93-H20 Hydro-Zinc[11] | >= 4" | CLD 23 | PUR | |
| Series 94-H2O Hydro-Zinc[2] [12] | [27] | CLD 23 | PUR | |
| Series FC22 Epoxoline[2] [14] | >= 2" | CLD 23 | EPOXY | |
| Series N140 Pota-Pox Plus[18] [22] | >= 4" | CLD 23 | EPOXY | |
| Series N140 Pota-Pox Plus [2] [17] | >= 4" | CLD 23 | EPOXY | |
| Series N140F Pota-Pox Plus Fast Cure[18] [19] | >= 4" | CLD 23 | EPOXY | |
[1] Colors: 1255 Beige, 1218 Blue, WH11 White
Number of Coats: 1-2
Maximum Field Use Dry Film Thickness (in mils): 50
Maximum Thinner: 5% Thinner #2
Recoat Cure Time and Temperature: 16 hours at 75°F
Final Cure Time and Temperature: 5 days at 75°F
Special Comments: Mix ratio of Part A to Part B is 1:1 by volume. Optional use with
fiberglass flake S211-0220. The fiberglass flake can be added up to a rate of 1% by
weight after the Parts A and B are mixed together. Certified for use as a primer or
topcoat with any NSF Certified Tnemec coating system provided that both primer and
topcoat meet their individual certified end uses.
[2] Meets the health effects requirements of NSF/ANSI/CAN 600 according to the requirements
of NSF/ANSI/CAN 61 including the most current health effects criteria for xylenes,
toluene, and ethylbenzene.
[3] Colors: Greenish Gray
Number of Coats: 1
Maximum Field Use Dry Thickness (in mils): 4mils
Maximum Thinner: 25% Water
Recoat Cure Time and Temperature: 5 hours at 75F
Final Cure Time/Temperature: 7 days at 75F
Special Comments: Series 44-780 Accelerator may be added up to 1 fl. oz/gal. Series
98-H2O Hydro-Zinc is approved for use as a primer with any NSF Certified Tnemec topcoat
or coating system providing that both primer and topcoat meet their individual Certified
end uses. Cure for Series 98-H2O Hydro-Zinc primer is 5 hours at 75F. Top-coat is then
applied. Final cure is 7 days. Mix ratio of Part A:B:C is 1.4:0.6:1 by volume.
[4] Colors: 15BL Tank White, 1255 Beige, 1211 Red, 35GR Black, 39BL Delft Blue, Y2606 Romac
Yellow, 00WH Tnemec White, 11SF True Blue, B9118 Baker Blue, B5712 Westech Blue, B2592
RAL 5009 Azurblau, B9695 Houston Blue, A14130 Mueller Gray, R5477 Mueller Sienna Red.
Number of Coats: 1
Sequence of Coats: 4 mils
Maximum Thinner: 10% No. 4 Thinner by volume
Recoat Cure Time and Temperature: 5 hours at 75F
Final Cure Time/Temperature: 7 days at 75F (entire system)
Special Comments: Mix ration is 1 Part A to 1 Part B by volume. Certified for use as an
optional primer or intermediate topcoat with any Tnemec NSF certified primer and topcoat
coating system provided the primer, intermediate, and topcoat meet their certified end
uses.
[5] Colors: White
Number of Coats: 1-3
Maximum Field Use Dry Thickness (in mils): 18 mils
Maximum Thinner: 15% water
Recoat Cure Time and Temperature: 6 hours at 75F
Final Cure Time/Temperature: 7 days at 75F
Special Comments: Series 44-700 Accelerator may be added up to 1 fl. oz./gal. Series
1220 Tnemec Epoxy is approved for use as a primer or topcoat with any NSF Certified
Tnemec topcoat or coating system providing that both primer and topcoat meet their
individual Certified end uses. Mix ratio of Part A:Part B is 2:1 by volume.
[6] Colors: WH16 Off-White, 1255 Beige, 39BL Delft Blue, B5712 Westech Blue, 11SF True
Blue/Safety, 1211 Red Primer, A13096 Baker Dark Gray, B2592 RAL5009 Azurblau, B2506
Dezurik Blue, B9918 New Baker Blue
Number of Coats: 2
Maximum Field Use Dry Thickness(in mils): 20 mils
Maximum Thinner: None
Recoat Cure Time and Temperature: 16 hours at 75F
Final Cure Time/Temperature: 30 days at 75F
Special Comments: Mix ratio of A:B is 2:1 by volume. This is for pipe, fitting, pump and
valve end use.
[7] Colors: WH16 OFF-WHITE, 35GR Black, 33GR Gray, 39BL Delft Blue, 1255 Beige, B5712
Westech Blue, 11SF True Blue/Safety, 1211 Red Primer, A13096 Baker Dark Gray, B2592
RAL5009 Azurblau, B2506 Dezurik Blue, B9918 New Baker Blue
Number of Coats: 1-3
Maximum Field Use Dry Thickness(in mils): 20
Maximum Thinner: 5% F041-0088 Thinner Clear by volume
Recoat Cure Time and Temperature: 8 hours at 75F
Final Cure Time/Temperature: 7 days at 75F
Special Comments: Mix ratio of A:B is 2:1 by volume. Series 21 Epoxoline is approved for
use as a primer or topcoat with any NSF Certified Tnemec topcoat or coating system
providing that both primer and topcoat meet their individual Certified end uses.
[8] Colors: Greenish-gray
Number of Coats: 1
Maximum Field Use Dry Film Thickness (in mils): 4
Maximum Thinner: 10% Thinner No. 2 or 10% Thinner No. 3 by volume
Final Cure Time and Temperature: 4 hours at 75°F; 2 hours at 75°F when the accelerator
is used
Special Comments: Series 44-710 Urethane Accelerator may be added up to 4 fl. oz/gal.
Series 91-H2O™ Hydro-Zinc™ is approved for use with any NSF Certified Tnemec topcoat or
coating system providing that both primer and topcoat meet their individual Certified
end uses. Mix ratio of Part A:Part B is 70%:30% by volume.
[9] This coating used with Thinner #2 is Certified for use in pipes >=96", tanks >=50,000
gallons, fittings >=1", pumps >=1", and valves >=4".
[10] This coatings used with Thinner #3 is Certified for use in pipes >=96", tanks >=40,000
gallons, fittings >=1", pumps >=1/2", and valves >=1.75".
[11] Colors: Greenish-Gray
Maximum Field Use Dry Thickness(in mils): 4 mils
Maximum Thinner: 10% Thinner #2 by volume
Final Cure Time/Temperature: 8 hours at 75F. 4 hours at 75F if accelerator is used.
Special Comments: Series 44-710 accelerator may be used up to 4 fluid oz/gal. 93-H20
Hydro-Zinc is approved for use with any NSF Certified Tnemec topcoat or coating system
providing that both primer and topcoat meet their individual Certified end uses.
[12] Color: Greenish-Gray
Number of Coats: 1
Maximum Field Use Dry Film Thickness (in mils): 4
Maximum Thinner: 15% Tnemec No. 49 by volume or 10% Thinner No. 3 or 10% Thinner No. 2
Recoat Cure Time and Temperature: 8 hours at 75°F; 2 hours at 75°F when the accelerator
is used
Special Comments: Series 44-710 may be added up to 4 fl. oz/gal. 94-H2O is approved for
use with any NSF Certified Tnemec topcoat or coating system.
[14] Colors: WH08 White, R4875A Akzo Red, B8869A Epoxoline Blue
Number of Coats: 1
Sequence of Coats: N/A
Maximum Field Use Dry Film Thickness (in mils): 80
Maximum Thinner: None
Final Cure Time and Temperature: 24 hours at 75°F
Special Comments: Mix ratio of Part A:Part B is 1:2 by volume. Any Listed color of
series N140 or N140F may be used as a topcoat or primer for Series FC22 Epoxoline.
[17] Colors: 00WH Tnemec White, 1211 Red, 1255 Beige, 15BL Tank white, 35GR Black, 39BL Delft
blue, B5712 Westech Blue, 11SF True Blue, B9118 Baker Blue, B8314 Krausz Blue, Y2606
Romac Yellow, B2592 RAL 5009 Azurblau, B7011 Crispin Blue, B2506 Dezurik Blue, B9695
Houston Blue, A14130 Mueller Gray, R5477 Mueller Sienna Red.
Number of Coats: 1
Maximum Field Use Dry Thickness(in mils): 4 mils
Maximum Thinner: 10% No. 4 Thinner by volume
Recoat Cure Time and Temperature: 5 hours at 75°F
Final Cure Time and Temperature: 7 days at 75°F (entire system)
Special Comments: Mix ratio is 1 Part A to 1 Part B by volume. Certified for use
as an optional primer or intermediate coat with any Tnemec NSF certified primer
and topcoat coating system provided the primer, intermediate, and topcoat meet
their certified end uses. Part C (Series 44-700 Accelerator) is an optional additive to
Part A in the field and may be added at up to 4 fluid ounces per gallon of Part A.
[18] Meets the health effects requirements of NSF/ANSI/CAN 600 according to requirements of
NSF/ANSI/CAN 61 for pump, valve, and fitting end use.
[19] Colors: 00WH Tnemec White, 1211 Red, 1255 Beige, 15BL Tank White, 35GR Black, 39BL Delft
Blue, B2506 DeZurik Blue, B5712 Westech Blue, 11SF True Blue, B9118 Baker Blue, B7896
S-B Blue, Y2606 Romac Yellow, B2592 RAL 5009 Azurblau, B7011 Crispin Blue, B9695 Houston
Blue, A14130 Mueller Gray, R5477 Mueller Sienna Red.
Number of Coats: 2-3
Sequence of Coats: Any combination of Listed colors
Maximum Field Use Dry Film Thickness (in mils): 18
Maximum Thinner: 5% Tnemec No. 60 Thinner by volume
Recoat Cure Time and Temperature: 5 hours at 75°F
Final Cure Time and Temperature: 30 days at 75°F
Special comments: Any listed color of Series 22, FC22, N140 or 141 may be substituted as
a primer of topcoat for Series N140 Pota-Pox Plus provided that both primer and topcoat
meet their individual Certified end uses. The mix ratio of Part A:Part B is 1:1 by
volume.
[20] Colors: 1216 Greenish-Gray
Number of Coats: 1
Sequence of Coats: N/A
Maximum Field Use Dry Film Thickness (in mils): 4
Maximum Thinner: 10% Thinner No. 2
Recoat Cure Time and Temperature: 8 hours at 75°F
Special Comment: Series 44-710 may be added up to 4 fl. oz/gal. Approved for use as a
primer with any NSF Certified Tnemec topcoat or coating system provided that both primer
and topcoat meet their individual Certified end uses.
[22] Colors: 00WH Tnemec White, 1211 Red, 1255 Beige, 15BL Tank White, 35GR Black, 39BL Delft
Blue, B5712 Westech Blue, 11SF True Blue, B9118 Baker Blue, B8314 Krausz Blue, A13096
Baker Dark Gray, Y2606 Romac Yellow, B2592 RAL 5009 Azurblau, B7011 Crispin Blue, B2506
Dezurik Blue, B9695 Houston Blue, A14130 Mueller Gray, R5477 Mueller Sienna Red.
Number of Coats: 2-3
Sequence of Coats: Any combination of Listed colors
Maximum Field Use Dry Film Thickness (in mils): 18
Maximum Thinner: 5% Tnemec No. 60 Thinner by volume
Recoat Cure Time and Temperature: 5 hours at 75°F with accelerator, 9 hours at 75°F
without accelerator
Final Cure Time and Temperature: 30 days at 75°F
Special Comments: Any Listed color of Series 22, FC22, N140, or 141 may be substituted
as a primer of topcoat for Series N140 Pota-Pox Plus provided that both primer and
topcoat meet their individual Certified end uses. The mix ratio of Part A:Part B is 1:1
by volume. Part C (Series 44-700 Accelerator) is an optional addititve to Part A in the
field and may be added at up to 4 fluid ounces per two mixed gallons of parts A and B.
[27] This coating used with Thinner #49 is Certified for use in valves >= ¾”. This coating
used with Thinner #2 is Certified for use in valves >= 4”. This coating used with
Thinner #3 is Certified for use in valves >= 1.75”.
|
||||
Facility : Jinshan District, Shanghai, China
Protective (Barrier) Materials
| Water | Water | |||
| Water Contact | Contact | Contact | ||
| Trade Designation | Size Restriction | Temp | Material | |
|
Coatings - Fittings[1] |
||||
| Series N140 Pota-Pox Plus[2] | >= 8" | CLD 23 | EPOXY | |
| Series N140F Pota-Pox Plus Fast Cure[3] | >= 8" | CLD 23 | EPOXY | |
[1] Meets the health effects requirements of NSF/ANSI/CAN 600 according to requirements of
NSF/ANSI/CAN 61 for pump, valve, and fitting end use.
[2] Colors: 1211 Red, 1255 Beige,15BL Tank White, 39BL Delft Blue, 35GR Black, 00WH Tnemec
White, Y2606 Romac Yellow, B8314 Krausz Blue, B5712 Westech Blue, 11SF True Blue, B9118
Baker Blue, A13096 Baker Dark Gray, B2592 RAL 5009 Azurblau, B7011 Crispin Blue, B2506
Dezurik Blue, A14130 Mueller Gray, B9695 Houston Blue, R5477 Mueller Sienna Red.
Number of Coats: 2-3
Sequence of Coats: Any combination of Listed colors
Maximum Field Use Dry Film Thickness (in mils): 18
Maximum Thinner: 5% Tnemec No. 60 Thinner by volume
Recoat Cure Time and Temperature: 5 hours at 75°F with accelerator, 9 hours at 75°F
without accelerator
Final Cure Time and Temperature: 30 days at 75°F
Special Comments: Any listed color of Series 22, FC22, N140, or 141 may be substituted
as a primer of topcoat for Series N140 Pota-Pox Plus provided that both primer and
topcoat meet their individual Certified end uses. The mix ratio of Part A: Part B is 1:1
by volume. Part C (Series 44-700 Accelerator) is an optional additive to Part A in the
field and may be added at up to 4 fluid ounces per two mixed gallons of parts A and B.
[3] Colors: 1211 Red, 1255 Beige, B2506 DeZurik Blue, 15BL Tank White, 39BL Delft Blue, 35GR
Black, 00WH Tnemec White, B7896 S-B Blue, Y2606 Romac Yellow, B5712 Blue, B2592 RAL 5009
Azurblau, B7011 Crispin Blue, B9695 Houston Blue, A14130 Mueller Gray, R5477 Mueller
Sienna Red.
Number of Coats: 2
Sequence of Coats: Any combination of Listed colors
Maximum Field Use Dry film Thickness (in mils): 18
Maximum Thinner: 5% Tnemec No. 60 Thinner by volume
Recoat Cure Time and Temperature: 5 hours at 75°F
Final Cure Time and Temperature: 30 days at 75°F
Special Comments: Any listed color of Series 22, FC22, N140, or 141 may be substituted
as a primer of topcoat for Series N140 Pota-Pox Plus provided that both primer and
topcoat meet their individual Certified end uses. The mix ratio of Part A: Part B is 1:1
by volume.
|
||||
|
Coatings - Mechanical Devices[1] |
||||
| Series N140 Pota-Pox Plus [2] | [4] | CLD 23 | EPOXY | |
[1] Meets the health effects requirements of NSF/ANSI/CAN 600 according to requirements of
NSF/ANSI/CAN 61 for pump, valve, and fitting end use.
[2] Colors: 1211 Red, 1255 Beige,15BL Tank White, 39BL Delft Blue, 35GR Black, 00WH Tnemec
White, Y2606 Romac Yellow, B8314 Krausz Blue, B5712 Westech Blue, 11SF True Blue, B9118
Baker Blue, A13096 Baker Dark Gray, B2592 RAL 5009 Azurblau, B7011 Crispin Blue, B2506
Dezurik Blue, A14130 Mueller Gray, B9695 Houston Blue, R5477 Mueller Sienna Red.
Number of Coats: 2-3
Sequence of Coats: Any combination of Listed colors
Maximum Field Use Dry Film Thickness (in mils): 18
Maximum Thinner: 5% Tnemec No. 60 Thinner by volume
Recoat Cure Time and Temperature: 5 hours at 75°F with accelerator, 9 hours at 75°F
without accelerator
Final Cure Time and Temperature: 30 days at 75°F
Special Comments: Any listed color of Series 22, FC22, N140, or 141 may be substituted
as a primer of topcoat for Series N140 Pota-Pox Plus provided that both primer and
topcoat meet their individual Certified end uses. The mix ratio of Part A: Part B is 1:1
by volume. Part C (Series 44-700 Accelerator) is an optional additive to Part A in the
field and may be added at up to 4 fluid ounces per two mixed gallons of parts A and B.
[4] Certified for mechanical device end use (other than pump and valve) for a maximum of 4.6
sq. ft. per gpm.
|
||||
|
Coatings - Pump[1] |
||||
| Series N140 Pota-Pox Plus[2] | >= 4" | CLD 23 | EPOXY | |
| Series N140F Pota-Pox Plus Fast Cure[3] | >= 4" | CLD 23 | EPOXY | |
[1] Meets the health effects requirements of NSF/ANSI/CAN 600 according to requirements of
NSF/ANSI/CAN 61 for pump, valve, and fitting end use.
[2] Colors: 1211 Red, 1255 Beige,15BL Tank White, 39BL Delft Blue, 35GR Black, 00WH Tnemec
White, Y2606 Romac Yellow, B8314 Krausz Blue, B5712 Westech Blue, 11SF True Blue, B9118
Baker Blue, A13096 Baker Dark Gray, B2592 RAL 5009 Azurblau, B7011 Crispin Blue, B2506
Dezurik Blue, A14130 Mueller Gray, B9695 Houston Blue, R5477 Mueller Sienna Red.
Number of Coats: 2-3
Sequence of Coats: Any combination of Listed colors
Maximum Field Use Dry Film Thickness (in mils): 18
Maximum Thinner: 5% Tnemec No. 60 Thinner by volume
Recoat Cure Time and Temperature: 5 hours at 75°F with accelerator, 9 hours at 75°F
without accelerator
Final Cure Time and Temperature: 30 days at 75°F
Special Comments: Any listed color of Series 22, FC22, N140, or 141 may be substituted
as a primer of topcoat for Series N140 Pota-Pox Plus provided that both primer and
topcoat meet their individual Certified end uses. The mix ratio of Part A: Part B is 1:1
by volume. Part C (Series 44-700 Accelerator) is an optional additive to Part A in the
field and may be added at up to 4 fluid ounces per two mixed gallons of parts A and B.
[3] Colors: 1211 Red, 1255 Beige, B2506 DeZurik Blue, 15BL Tank White, 39BL Delft Blue, 35GR
Black, 00WH Tnemec White, B7896 S-B Blue, Y2606 Romac Yellow, B5712 Blue, B2592 RAL 5009
Azurblau, B7011 Crispin Blue, B9695 Houston Blue, A14130 Mueller Gray, R5477 Mueller
Sienna Red.
Number of Coats: 2
Sequence of Coats: Any combination of Listed colors
Maximum Field Use Dry film Thickness (in mils): 18
Maximum Thinner: 5% Tnemec No. 60 Thinner by volume
Recoat Cure Time and Temperature: 5 hours at 75°F
Final Cure Time and Temperature: 30 days at 75°F
Special Comments: Any listed color of Series 22, FC22, N140, or 141 may be substituted
as a primer of topcoat for Series N140 Pota-Pox Plus provided that both primer and
topcoat meet their individual Certified end uses. The mix ratio of Part A: Part B is 1:1
by volume.
|
||||
|
Coatings - Valve[1] |
||||
| Series N140 Pota-Pox Plus[2] | >= 4" | CLD 23 | EPOXY | |
| Series N140F Pota-Pox Plus Fast Cure[3] | >= 4" | CLD 23 | EPOXY | |
[1] Meets the health effects requirements of NSF/ANSI/CAN 600 according to requirements of
NSF/ANSI/CAN 61 for pump, valve, and fitting end use.
[2] Colors: 1211 Red, 1255 Beige,15BL Tank White, 39BL Delft Blue, 35GR Black, 00WH Tnemec
White, Y2606 Romac Yellow, B8314 Krausz Blue, B5712 Westech Blue, 11SF True Blue, B9118
Baker Blue, A13096 Baker Dark Gray, B2592 RAL 5009 Azurblau, B7011 Crispin Blue, B2506
Dezurik Blue, A14130 Mueller Gray, B9695 Houston Blue, R5477 Mueller Sienna Red.
Number of Coats: 2-3
Sequence of Coats: Any combination of Listed colors
Maximum Field Use Dry Film Thickness (in mils): 18
Maximum Thinner: 5% Tnemec No. 60 Thinner by volume
Recoat Cure Time and Temperature: 5 hours at 75°F with accelerator, 9 hours at 75°F
without accelerator
Final Cure Time and Temperature: 30 days at 75°F
Special Comments: Any listed color of Series 22, FC22, N140, or 141 may be substituted
as a primer of topcoat for Series N140 Pota-Pox Plus provided that both primer and
topcoat meet their individual Certified end uses. The mix ratio of Part A: Part B is 1:1
by volume. Part C (Series 44-700 Accelerator) is an optional additive to Part A in the
field and may be added at up to 4 fluid ounces per two mixed gallons of parts A and B.
[3] Colors: 1211 Red, 1255 Beige, B2506 DeZurik Blue, 15BL Tank White, 39BL Delft Blue, 35GR
Black, 00WH Tnemec White, B7896 S-B Blue, Y2606 Romac Yellow, B5712 Blue, B2592 RAL 5009
Azurblau, B7011 Crispin Blue, B9695 Houston Blue, A14130 Mueller Gray, R5477 Mueller
Sienna Red.
Number of Coats: 2
Sequence of Coats: Any combination of Listed colors
Maximum Field Use Dry film Thickness (in mils): 18
Maximum Thinner: 5% Tnemec No. 60 Thinner by volume
Recoat Cure Time and Temperature: 5 hours at 75°F
Final Cure Time and Temperature: 30 days at 75°F
Special Comments: Any listed color of Series 22, FC22, N140, or 141 may be substituted
as a primer of topcoat for Series N140 Pota-Pox Plus provided that both primer and
topcoat meet their individual Certified end uses. The mix ratio of Part A: Part B is 1:1
by volume.
|
||||
Number of matching Manufacturers is 1
Number of matching Products is 141
Processing time was 0 seconds
