NSF Product and Service Listings

These NSF Official Listings are current as of Friday, December 26, 2025 at 12:15 a.m. Eastern Time. Please contact NSF to confirm the status of any Listing, report errors, or make suggestions.

Alert: NSF is concerned about fraudulent downloading and manipulation of website text. Always confirm this information by clicking on the below link for the most accurate information: http://info.nsf.org/Certified/PwsComponents/Listings.asp?Company=C0171333&Standard=061&


NSF/ANSI/CAN 61
Drinking Water System Components - Health Effects

NOTE: Unless otherwise indicated for Materials, Certification is only for the Water Contact Material shown in the Listing. Click here for a list of Abbreviations used in these Listings. Click here for the definitions of Water Contact Temperatures denoted in these Listings. Products certified to NSF/ANSI/CAN 61 comply with the health effects criteria in NSF/ANSI/CAN 600.

 
The Sherwin-Williams Company 
101 West Prospect Avenue
Cleveland, OH 44115 
United States 
216-566-2000


Facility : # 1 USA

Protective (Barrier) Materials

    Water Water
  Water Contact Contact Contact
Trade Designation Size Restriction Temp Material

Coatings - Fittings[1]
Poly-Cote 110[2] [3] >= 2" CLD 23 PUR
Poly-Cote 110 Fast Set[2] [3] >= 2" CLD 23 PUR
Poly-Cote 110 Rapid Set[2] [3] >= 2" CLD 23 PUR
Poly-Cote 115[4] >= 2" CLD 23 PUR 

[1] Meets the applicable health effects requirements of NSF/ANSI/CAN 600 according to the
    requirements of NSF/ANSI/CAN 61 including the most current health effects criteria for
    xylenes, toluene, and ethylbenzene.
[2] Colors: Off-white, gray, blue, tan, brown, green, purple, red, black, yellow
    Number of Coats: Unlimited
    Maximum Field Use Dry Film Thickness (in mils): 250
    Recoat Cure Time and Temperature: None - subsequent coats may be applied immediately
    Final Cure Time and Temperature: 24 hours at 70°F
    Special Comments: The coating may be applied in as many coats as necessary up to a
    maximum dry film thickness of 250
    mils. Mix ratio of polyol to isocyanate is 1:1 by volume. Minimum field use dry film
    thickness is 20 mils.
[3] Certification not for immediate-return-to-service pipe coating.
[4] Colors: Beige, Black, Gray
    Number of Coats: 1
    Maximum Field Use Dry Film Thickness (in mils): 250
    Final Cure Time and Temperature: 72 hours at 75°F
    Special Comments: Mix ratio of Part B:Part A of Poly-Cote 115 is 3:1 by volume. Minimum
    field use dry film thickness is 20 mils.

Coatings - Pipe[1]
Poly-Cote 110[2] [3] >= 8" CLD 23 PUR
Poly-Cote 110 Fast Set[2] [3] >= 8" CLD 23 PUR
Poly-Cote 110 Rapid Set[2] [3] >= 8" CLD 23 PUR
Poly-Cote 115[4] >= 8" CLD 23 PUR 

[1] Meets the applicable health effects requirements of NSF/ANSI/CAN 600 according to the
    requirements of NSF/ANSI/CAN 61 including the most current health effects criteria for
    xylenes, toluene, and ethylbenzene.
[2] Colors: Off-white, gray, blue, tan, brown, green, purple, red, black, yellow
    Number of Coats: Unlimited
    Maximum Field Use Dry Film Thickness (in mils): 250
    Recoat Cure Time and Temperature: None - subsequent coats may be applied immediately
    Final Cure Time and Temperature: 24 hours at 70°F
    Special Comments: The coating may be applied in as many coats as necessary up to a
    maximum dry film thickness of 250
    mils. Mix ratio of polyol to isocyanate is 1:1 by volume. Minimum field use dry film
    thickness is 20 mils.
[3] Certification not for immediate-return-to-service pipe coating.
[4] Colors: Beige, Black, Gray
    Number of Coats: 1
    Maximum Field Use Dry Film Thickness (in mils): 250
    Final Cure Time and Temperature: 72 hours at 75°F
    Special Comments: Mix ratio of Part B:Part A of Poly-Cote 115 is 3:1 by volume. Minimum
    field use dry film thickness is 20 mils.

Coatings - Tank[1]
Poly-Cote 110[2] [3] >= 50 gal. CLD 23 PUR
Poly-Cote 110 Fast Set[2] [3] >= 50 gal. CLD 23 PUR
Poly-Cote 110 Rapid Set[2] [3] >= 50 gal. CLD 23 PUR
Poly-Cote 115[4] >= 50 gal. CLD 23 PUR 

[1] Meets the applicable health effects requirements of NSF/ANSI/CAN 600 according to the
    requirements of NSF/ANSI/CAN 61 including the most current health effects criteria for
    xylenes, toluene, and ethylbenzene.
[2] Colors: Off-white, gray, blue, tan, brown, green, purple, red, black, yellow
    Number of Coats: Unlimited
    Maximum Field Use Dry Film Thickness (in mils): 250
    Recoat Cure Time and Temperature: None - subsequent coats may be applied immediately
    Final Cure Time and Temperature: 24 hours at 70°F
    Special Comments: The coating may be applied in as many coats as necessary up to a
    maximum dry film thickness of 250
    mils. Mix ratio of polyol to isocyanate is 1:1 by volume. Minimum field use dry film
    thickness is 20 mils.
[3] Certification not for immediate-return-to-service pipe coating.
[4] Colors: Beige, Black, Gray
    Number of Coats: 1
    Maximum Field Use Dry Film Thickness (in mils): 250
    Final Cure Time and Temperature: 72 hours at 75°F
    Special Comments: Mix ratio of Part B:Part A of Poly-Cote 115 is 3:1 by volume. Minimum
    field use dry film thickness is 20 mils.

Coatings - Valve[1]
Poly-Cote 110[2] [3] >= 2" CLD 23 PUR
Poly-Cote 110 Fast Set[2] [3] >= 2" CLD 23 PUR
Poly-Cote 110 Rapid Set[2] [3] >= 2" CLD 23 PUR
Poly-Cote 115[4] >= 2" CLD 23 PUR 

[1] Meets the applicable health effects requirements of NSF/ANSI/CAN 600 according to the
    requirements of NSF/ANSI/CAN 61 including the most current health effects criteria for
    xylenes, toluene, and ethylbenzene.
[2] Colors: Off-white, gray, blue, tan, brown, green, purple, red, black, yellow
    Number of Coats: Unlimited
    Maximum Field Use Dry Film Thickness (in mils): 250
    Recoat Cure Time and Temperature: None - subsequent coats may be applied immediately
    Final Cure Time and Temperature: 24 hours at 70°F
    Special Comments: The coating may be applied in as many coats as necessary up to a
    maximum dry film thickness of 250
    mils. Mix ratio of polyol to isocyanate is 1:1 by volume. Minimum field use dry film
    thickness is 20 mils.
[3] Certification not for immediate-return-to-service pipe coating.
[4] Colors: Beige, Black, Gray
    Number of Coats: 1
    Maximum Field Use Dry Film Thickness (in mils): 250
    Final Cure Time and Temperature: 72 hours at 75°F
    Special Comments: Mix ratio of Part B:Part A of Poly-Cote 115 is 3:1 by volume. Minimum
    field use dry film thickness is 20 mils.

Number of matching Manufacturers is 1
Number of matching Products is 16
Processing time was 0 seconds