NSF Product and Service Listings
These NSF Official Listings are current as of Wednesday, April 15, 2026 at 12:15 a.m. Eastern Time. Please contact NSF to confirm the status of any Listing, report errors, or make suggestions.
Alert: NSF is concerned about fraudulent downloading and manipulation of website text. Always confirm this information by clicking on the below link for the most accurate information: http://info.nsf.org/Certified/PwsComponents/Listings.asp?Company=C0177665&Standard=061&
NSF/ANSI/CAN 61
Drinking Water System Components - Health Effects
Drinking Water System Components - Health Effects
NOTE: Unless otherwise indicated for Materials, Certification is only for the Water Contact Material shown in the Listing. Click here for a list of Abbreviations used in these Listings. Click here for the definitions of Water Contact Temperatures denoted in these Listings. Products certified to NSF/ANSI/CAN 61 comply with the health effects criteria in NSF/ANSI/CAN 600.
| Tstrata Strengthening Solutions | |
| 10150 Old Columbia Road | |
| Columbia, MD 21046 | |
| United States | |
| 410-859-6539 | |
| Visit this company's website |
Facility : West Chicago, IL
Protective (Barrier) Materials
| Water | Water | |||
| Water Contact | Contact | Contact | ||
| Trade Designation | Size Restriction | Temp | Material | |
|
Coatings - Immediate Return to Service[1] |
||||
| Composite Strengthening System | >=60" | CLD 23 | EPOXY | |
[1] Product is applied in multiple layers with Layers 1, 2, and 3 optional:
Layer 1: CSS-ES Epoxy Primer and Saturant apply 10 wet mils maximum. Mix ratio of Part
A to B is 2:1 by volume. Mix with a drill and mixing paddle until uniformly blended (5
minutes at 500 rpm).
until uniformly blended (5 minutes at 500 rpm).
Layer 2: CSS-EP Paste and Filler apply 40 wet mils maximum. Mix ratio of Part A to B is
2:1 by volume. Mix with a drill and mixing paddle until uniformly blended (5 minutes at
500 rpm).
uniformly blended (5 minutes at 500 rpm).
Layer 3: CSS-CUGF27 or CSS V-Wrap EG50 Fabric saturated with CSS-ES Epoxy Primer and
Saturant (follow mixing instructions above). Apply with maximum thickness of 50 mils. It
is permitted to place Layer 3 between layers of carbon fabric (Layers 4+).
Layer 4: CSS-CUCF11, CSS-CUCF22, CSS-CUCF44, CSS V-WRAP C110 HM, CSS V-WRAP C220HM, or
CSS V-Wrap C440HM Fabric saturated with CSS-ES Epoxy Primer and Saturant (follow mixing
instructions above).
Apply 1 - 10 layers with a maximum
thickness of 20 mils per layer of CSS-CUCF11 or CSS V-WRAP C110 HM; 40 mils per layer of
CSS-CUCF22 or CSS V-WRAP C220HM; or 80 mils per layer of CSS CUCF44 or CSS V-Wrap
C440HM.
Saturation rate for fabrics: 1 gallon per 75 square feet of CSS-CUCF11 or CSS V-WRAP
C110 HM; 1 gallon per 50 square feet of CSS-CUCF22 or CSS V-WRAP C220HM; 1 gallon per 50
square feet of CSS-CUGF27 or CSS V-Wrap EG50; and 1 gallon per 25 square feet of
CSS-CUCF44 or CSS V-Wrap C440HM.
Final cure time is 72 hours at 70°F after application of final layer. There is no cure
required between the application of layers.
|
||||
|
Coatings - Tank[1] |
||||
| Composite Strengthening System | >=6,000 gal | CLD 23 | EPOXY | |
[1] Product is applied in multiple layers with Layers 1, 2, and 3 optional:
Layer 1: CSS-ES Epoxy Primer and Saturant apply 10 wet mils maximum. Mix ratio of Part
A to B is 2:1 by volume. Mix with a drill and mixing paddle until uniformly blended (5
minutes at 500 rpm).
until uniformly blended (5 minutes at 500 rpm).
Layer 2: CSS-EP Paste and Filler apply 40 wet mils maximum. Mix ratio of Part A to B is
2:1 by volume. Mix with a drill and mixing paddle until uniformly blended (5 minutes at
500 rpm).
uniformly blended (5 minutes at 500 rpm).
Layer 3: CSS-CUGF27 or CSS V-Wrap EG50 Fabric saturated with CSS-ES Epoxy Primer and
Saturant (follow mixing instructions above). Apply with maximum thickness of 50 mils. It
is permitted to place Layer 3 between layers of carbon fabric (Layers 4+).
Layer 4: CSS-CUCF11, CSS-CUCF22, CSS-CUCF44, CSS V-WRAP C110 HM, CSS V-WRAP C220HM, or
CSS V-Wrap C440HM Fabric saturated with CSS-ES Epoxy Primer and Saturant (follow mixing
instructions above).
Apply 1 - 10 layers with a maximum
thickness of 20 mils per layer of CSS-CUCF11 or CSS V-WRAP C110 HM; 40 mils per layer of
CSS-CUCF22 or CSS V-WRAP C220HM; or 80 mils per layer of CSS CUCF44 or CSS V-Wrap
C440HM.
Saturation rate for fabrics: 1 gallon per 75 square feet of CSS-CUCF11 or CSS V-WRAP
C110 HM; 1 gallon per 50 square feet of CSS-CUCF22 or CSS V-WRAP C220HM; 1 gallon per 50
square feet of CSS-CUGF27 or CSS V-Wrap EG50; and 1 gallon per 25 square feet of
CSS-CUCF44 or CSS V-Wrap C440HM.
Final cure time is 72 hours at 70°F after application of final layer. There is no cure
required between the application of layers.
|
||||
|
Coatings - Pipe[2] |
||||
| CSS V-Wrap 770 | 36" - 312" | CLD 23 | EPOXY | |
[2] Product is applied in 5 layers:
Combine the contents of V-Wrap 770-A pail and V-Wrap 770-B pail together and mix for 3
minutes using a mixer speed of 400-600 RPM until uniformly blended. Transfer the mixed
epoxy into the other pail and mix for an additional 2 minutes.
Layer 1: 10 wet mils of V-Wrap 770 resin. Mix ratio of V-Wrap 770 resin part A:B is
100:33 by weight.
Layer 2: 40 wet mils of thickened V-Wrap 770 resin. Thickened V-Wrap 770 is achieved by
adding fumed silica to the resin at a maximum ratio of 1.5 parts fumed silica to 1 part
resin by volume
Layer 3: 8 coats of V-Wrap EG50 or V-Wrap EG50B Fabric satuarated with V-Wrap 770 resin.
The thickness of each coat/layer of fabric is 50 mils.
Layer 4: 8 coats of V-Wrap C100H, V-Wrap C200H, or V-Wrap C400H Fabric saturated with
V-Wrap 770 resin. The thickness of each coat/layer of fabric is 90 mils.
Layer 5: 40 wet mils of thickened V-Wrap 770 resin. Thickened V-Wrap 770 is achieved by
adding fumed silica to the resin at a maximum ratio of 1.5 parts fumed silica to 1 part
resin by volume.
The final cure time and temperature is 24 hours at 75ºF. There is no cure time required
between the application of layers.
|
||||
|
Coatings - Fittings[1] |
||||
| Composite Strengthening System | >=1" | CLD 23 | EPOXY | |
[1] Product is applied in multiple layers with Layers 1, 2, and 3 optional:
Layer 1: CSS-ES Epoxy Primer and Saturant apply 10 wet mils maximum. Mix ratio of Part
A to B is 2:1 by volume. Mix with a drill and mixing paddle until uniformly blended (5
minutes at 500 rpm).
until uniformly blended (5 minutes at 500 rpm).
Layer 2: CSS-EP Paste and Filler apply 40 wet mils maximum. Mix ratio of Part A to B is
2:1 by volume. Mix with a drill and mixing paddle until uniformly blended (5 minutes at
500 rpm).
uniformly blended (5 minutes at 500 rpm).
Layer 3: CSS-CUGF27 or CSS V-Wrap EG50 Fabric saturated with CSS-ES Epoxy Primer and
Saturant (follow mixing instructions above). Apply with maximum thickness of 50 mils. It
is permitted to place Layer 3 between layers of carbon fabric (Layers 4+).
Layer 4: CSS-CUCF11, CSS-CUCF22, CSS-CUCF44, CSS V-WRAP C110 HM, CSS V-WRAP C220HM, or
CSS V-Wrap C440HM Fabric saturated with CSS-ES Epoxy Primer and Saturant (follow mixing
instructions above).
Apply 1 - 10 layers with a maximum
thickness of 20 mils per layer of CSS-CUCF11 or CSS V-WRAP C110 HM; 40 mils per layer of
CSS-CUCF22 or CSS V-WRAP C220HM; or 80 mils per layer of CSS CUCF44 or CSS V-Wrap
C440HM.
Saturation rate for fabrics: 1 gallon per 75 square feet of CSS-CUCF11 or CSS V-WRAP
C110 HM; 1 gallon per 50 square feet of CSS-CUCF22 or CSS V-WRAP C220HM; 1 gallon per 50
square feet of CSS-CUGF27 or CSS V-Wrap EG50; and 1 gallon per 25 square feet of
CSS-CUCF44 or CSS V-Wrap C440HM.
Final cure time is 72 hours at 70°F after application of final layer. There is no cure
required between the application of layers.
|
||||
Facility : Columbia, MD
Protective (Barrier) Materials
| Water | Water | |||
| Water Contact | Contact | Contact | ||
| Trade Designation | Size Restriction | Temp | Material | |
|
Coatings - Pipe |
||||
| V-Wrap 770[1] [G] | 36" - 312" | CLD 23 | EPOXY | |
| V-Wrap PF[2] [G] | 60" - 312" | CLD 23 | EPOXY | |
[1] Product is applied in 5 layers:
Combine the contents of V-Wrap 770-A pail and V-Wrap 770-B pail together and mix for 3
minutes using a mixer speed of 400-600 RPM until uniformly blended. Transfer the mixed
epoxy into the other pail and mix for an additional 2 minutes.
Layer 1: 10 wet mils of V-Wrap 770 resin. Mix ratio of V-Wrap 770 resin part A:B is
100:33 by weight.
Layer 2: 40 wet mils of thickened V-Wrap 770 resin. Thickened V-Wrap 770 is achieved by
adding fumed silica to the resin at a maximum ratio of 1.5 parts fumed silica to 1 part
resin by volume.
Layer 3: 8 coats of V-Wrap EG50 or V-Wrap EG50B Fabric saturated with V-Wrap 770 resin.
The thickness of each coat/layer of fabric is 50 mils. High strength steel wire
(conforming to ASTM A881 specification) may be embedded in between fabric layers with
V-Wrap 770 Thickened epoxy. Wires measure 0.2-inch (5 mm) diameter and are helically
wound into place with a typical spacing of 0.4 inch (10 mm) on center.
Layer 4: 8 coats of V-Wrap C100H, V-Wrap C100HM, V-Wrap C200H, V-Wrap C200HM, V-Wrap
C220B, V-Wrap C400H, V-Wrap C400HM, or V-Wrap C440HMA Fabric saturated with V-Wrap 770
resin. The thickness of each coat/layer of fabric is 90 mils. High strength steel wire
(conforming to ASTM A881 specification) may be embedded in between fabric layers with
V-Wrap 770 Thickened epoxy. Wires measure 0.2-inch (5 mm) diameter and are helically
wound into place with a typical spacing of 0.4 inch (10 mm) on center.
Layer 5: 40 wet mils of thickened V-Wrap 770 resin. Thickened V-Wrap 770 is achieved by
adding fumed silica to the resin at a maximum ratio of 1.5 parts fumed silica to 1 part
resin by volume.
The final cure time and temperature is 24 hours at 75ºF. There is no cure time required
between the application of layers.
[2] Product is applied in 4 layers:
Combine the contents of V-Wrap 770-A pail and V-Wrap 770-B pail together and mix for 3
minutes using a mixer speed of 400-600 RPM until uniformly blended. Transfer the mixed
epoxy into the other pail and mix for an additional 2 minutes.
Layer 1: 10 wet mils of V-Wrap 770 Resin. Mix ratio of V-Wrap 770 Resin Part A:B is
100:33 by weight.
Layer 2: 40 wet mils of V-Wrap PF Putty. Mix ratio of V-Wrap Putty is Part A:B is
100:31.5 by weight.
Layer 3: 4 coats of V-Wrap EG50 or V-Wrap EG50B Fabric saturated with V-Wrap 770 resin.
The thickness of each coat/layer of fabric is 50 mils. High strength steel wire
(conforming to ASTM A881 specification) may be embedded in between fabric layers with
V-Wrap 770 Thickened epoxy. Wires measure 0.2-inch (5 mm) diameter and are helically
wound into place with a typical spacing of 0.4 inch (10 mm) on center.
Layer 4: 6 coats of V-Wrap C100H, V-Wrap C100HM, V-Wrap C200H, V-Wrap C200HM, V-Wrap
C220B, V-Wrap C400H, or V-Wrap C400HM Fabric saturated with V-Wrap 770 resin. High
strength steel wire (conforming to ASTM A881 specification) may be embedded in between
fabric layers with V-Wrap 770 Thickened epoxy. Wires measure 0.2-inch (5 mm) diameter
and are helically wound into place with a typical spacing of 0.4 inch (10 mm) on center.
The final cure time and temperature for the system is 24 hours at 75°F. There is no
cure time between the application of layers.
[G] Product is Certified to NSF/ANSI/CAN 372 and conforms with the lead content requirements
for "lead free" plumbing as defined by California, Vermont, Maryland, and Louisiana
state laws and the U.S. Safe Drinking Water Act.
|
||||
Number of matching Manufacturers is 1
Number of matching Products is 6
Processing time was 0 seconds
