NSF Product and Service Listings

These NSF Official Listings are current as of Thursday, November 13, 2025 at 12:15 a.m. Eastern Time. Please contact NSF to confirm the status of any Listing, report errors, or make suggestions.

Alert: NSF is concerned about fraudulent downloading and manipulation of website text. Always confirm this information by clicking on the below link for the most accurate information: http://info.nsf.org/Certified/PwsComponents/Listings.asp?Company=C0335992&Standard=061&


NSF/ANSI/CAN 61
Drinking Water System Components - Health Effects

NOTE: Unless otherwise indicated for Materials, Certification is only for the Water Contact Material shown in the Listing. Click here for a list of Abbreviations used in these Listings. Click here for the definitions of Water Contact Temperatures denoted in these Listings. Products certified to NSF/ANSI/CAN 61 comply with the health effects criteria in NSF/ANSI/CAN 600.

 
NOV Fiber Glass Systems 
2700 West 65th Street
Little Rock, AR 72209 
United States 
501-618-2278
Visit this company's website


Facility : Little Rock, AR

Joining and Sealing Materials

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Adhesives
8000 Series Adhesive and Hardener[1] [2] >= 1" CLD 23 EPOXY
PSX-20 Adhesive and Hardener[3] >= 1" C. HOT ADH
PSX-34 Adhesive and Hardener[4] >= 1" C. HOT ADH
PSX-48 Adhesive[5] >= 1" C. HOT ADH
PSX-60 Adhesive and Hardener[6] >= 1" C. HOT ADH
Weldfast CL-200 Vinyl Ester Adhesive[7] >= 1" CLD 23 ADH 

[1] 8000 Series Adhesive and Hardener includes the following trade names: DS-8014, DS-8024,
    DS-8069, DS-8071, DS-8088-S, DS-8088-L, and DS-8069-C.
[2] Mix ratio is 7.6:1 (A:B) by weight but will vary slightly based on the kit size. 
    Minimum cure time is 1 hour at 100° F.  Please follow the manufacturer’s instructions
    supplied with each kit.
[3] Mix ratio is 3.2:1 (A:B) by weight.  Minimum cure time is 1 hour at 100° F.  The mix
    ratios will vary slightly based on the kit size.  Please follow the manufacturer’s
    instructions supplied with each kit.
[4] Mix ratio is 3.2:1 (A:B) by weight.  Minimum cure time is 1 hour at 110° F.  The mix
    ratios will vary slightly based on the kit size.  Please follow the manufacturer’s
    instructions supplied with each kit.
[5] Mix ratio of adhesive to hardener is 100:26.62 (A:B) by weight. Minimum cure time is 35
    minutes at 77° F. Please follow the manufacturer’s instructions supplied with each kit.
[6] Mix ratio is 3.2:1 (A:B) by weight.  Minimum cure time is 3 hours at 100° F.  The mix
    ratios will vary slightly based on the kit size.  Please follow the manufacturer’s
    instructions supplied with each kit.
[7] Mix ratio is 45:1 (A:B) by weight.  Minimum cure time is 24 hours at 71 - 100° F.  The
    mix ratios will vary slightly based on the kit size.  Please follow the manufacturer’s
    instructions supplied with each kit.


Pipes and Related Products

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Fittings
Green Thread HP Compression Molded Fittings >= 1" C. HOT TSRE
Green Thread HP Fittings >= 1" CLD 23 TSRE
Red Thread HP Compression Molded Fittings >= 1" C. HOT TSRE
Red Thread HP Fittings >= 2" CLD 23 TSRE

Pipe
Green Thread HP Pipe >= 1" CLD 23 TSRE
Red Thread HP Pipe >= 2" CLD 23 TSRE



Facility : Sand Springs, OK

Pipes and Related Products

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Fittings
GTHP 16 Fitting >= 1 in C. HOT TSRE



Facility : Qingdao, China

Pipes and Related Products

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Fittings[1]
GTHP Fitting >= 1" C. HOT TSRE 

[1] Certification is for fittings manufactured by filament wound/hand lay-up/compression
    molding process.

Number of matching Manufacturers is 1
Number of matching Products is 14
Processing time was 0 seconds