NSF Product and Service Listings
These NSF Official Listings are current as of Monday, December 2, 2024 at 12:15 a.m. Eastern Time. Please contact NSF to confirm the status of any Listing, report errors, or make suggestions.
Alert: NSF is concerned about fraudulent downloading and manipulation of website text. Always confirm this information by clicking on the below link for the most accurate information: http://info.nsf.org/Certified/PwsComponents/Listings.asp?Company=C0335992&Standard=061&
NSF/ANSI/CAN 61
Drinking Water System Components - Health Effects
Drinking Water System Components - Health Effects
NOTE: Unless otherwise indicated for Materials, Certification is only for the Water Contact Material shown in the Listing. Click here for a list of Abbreviations used in these Listings. Click here for the definitions of Water Contact Temperatures denoted in these Listings. Products certified to NSF/ANSI/CAN 61 comply with the health effects criteria in NSF/ANSI/CAN 600.
NOV Fiber Glass Systems | |
2700 West 65th Street | |
Little Rock, AR 72209 | |
United States | |
501-618-2278 | |
Visit this company's website |
Facility : Little Rock, AR
Joining and Sealing Materials
Water | Water | |||
Contact | Contact | |||
Trade Designation | Size | Temp | Material | |
Adhesives |
||||
8000 Series Adhesive and Hardener[1] [2] | >= 1" | CLD 23 | EPOXY | |
PSX-20 Adhesive and Hardener[3] | >= 1" | C. HOT | ADH | |
PSX-34 Adhesive and Hardener[4] | >= 1" | C. HOT | ADH | |
PSX-48 Adhesive[5] | >= 1" | C. HOT | ADH | |
PSX-60 Adhesive and Hardener[6] | >= 1" | C. HOT | ADH | |
Weldfast CL-200 Vinyl Ester Adhesive[7] | >= 1" | CLD 23 | ADH | |
[1] 8000 Series Adhesive and Hardener includes the following trade names: DS-8014, DS-8024, DS-8069, DS-8071, DS-8088-S, DS-8088-L, and DS-8069-C. [2] Mix ratio is 7.6:1 (A:B) by weight but will vary slightly based on the kit size. Minimum cure time is 1 hour at 100° F. Please follow the manufacturer’s instructions supplied with each kit. [3] Mix ratio is 3.2:1 (A:B) by weight. Minimum cure time is 1 hour at 100° F. The mix ratios will vary slightly based on the kit size. Please follow the manufacturer’s instructions supplied with each kit. [4] Mix ratio is 3.2:1 (A:B) by weight. Minimum cure time is 1 hour at 110° F. The mix ratios will vary slightly based on the kit size. Please follow the manufacturer’s instructions supplied with each kit. [5] Mix ratio of adhesive to hardener is 100:26.62 (A:B) by weight. Minimum cure time is 35 minutes at 77° F. Please follow the manufacturer’s instructions supplied with each kit. [6] Mix ratio is 3.2:1 (A:B) by weight. Minimum cure time is 3 hours at 100° F. The mix ratios will vary slightly based on the kit size. Please follow the manufacturer’s instructions supplied with each kit. [7] Mix ratio is 45:1 (A:B) by weight. Minimum cure time is 24 hours at 71 - 100° F. The mix ratios will vary slightly based on the kit size. Please follow the manufacturer’s instructions supplied with each kit. |
Pipes and Related Products
Water | Water | |||
Contact | Contact | |||
Trade Designation | Size | Temp | Material | |
Fittings |
||||
Green Thread HP Compression Molded Fittings | >= 1" | C. HOT | TSRE | |
Green Thread HP Fittings | >= 1" | CLD 23 | TSRE | |
Red Thread HP Compression Molded Fittings | >= 1" | C. HOT | TSRE | |
Red Thread HP Fittings | >= 2" | CLD 23 | TSRE | |
Pipe |
||||
Green Thread HP Pipe | >= 1" | CLD 23 | TSRE | |
Red Thread HP Pipe | >= 2" | CLD 23 | TSRE |
Number of matching Manufacturers is 1
Number of matching Products is 12
Processing time was 0 seconds