NSF Product and Service Listings

These NSF Official Listings are current as of Sunday, January 5, 2025 at 12:15 a.m. Eastern Time. Please contact NSF to confirm the status of any Listing, report errors, or make suggestions.

Alert: NSF is concerned about fraudulent downloading and manipulation of website text. Always confirm this information by clicking on the below link for the most accurate information: http://info.nsf.org/Certified/PwsComponents/Listings.asp?Company=C0349274&Standard=061&


NSF/ANSI/CAN 61
Drinking Water System Components - Health Effects

NOTE: Unless otherwise indicated for Materials, Certification is only for the Water Contact Material shown in the Listing. Click here for a list of Abbreviations used in these Listings. Click here for the definitions of Water Contact Temperatures denoted in these Listings. Products certified to NSF/ANSI/CAN 61 comply with the health effects criteria in NSF/ANSI/CAN 600.

 
Royal Coatings, Inc. 
2705 Concord Road
Belle Chasse, LA 70037 
United States 
800-815-8811 
504-392-8811


Facility : # 1 USA

Protective (Barrier) Materials

    Water Water
  Water Contact Contact Contact
Trade Designation Size Restriction Temp Material

Coatings - Pipe[1] [2]
PC 2.8 3/4" CLD 23 ASPH
Seal coat ID 3/4" CLD 23 ASPH
Tuff Coat OD 3/4" CLD 23 ASPH 

[1] Colors: Black
    Number of Coats: 1 - 4
    Maximum flied use dry film thickness (in mils): 5
    Recoat cure time and temperature : 7 days at 70°C (158°F)
    Final cure time and temperature: 7 days at 70°C (158°F)
    Special comments: Pre-heat coating and substrate to 120°F - 140°F (49°C - 60°C) prior to
    application. Maintain adequate air circulation and ventilation. During curing period
    atomized air drying system is highly recommended. Following application flush wash the
    pipe with running water for 10 hours. 
[2] Only products bearing the NSF Mark on the product, product packaging, and/or
    documentation shipped with the product are Certified.

Coatings - Valve[1] [2]
PC 2.8 3/4" CLD 23 ASPH
Seal coat ID 3/4" CLD 23 ASPH
Tuff Coat OD 3/4" CLD 23 ASPH 

[1] Colors: Black
    Number of Coats: 1 - 4
    Maximum flied use dry film thickness (in mils): 5
    Recoat cure time and temperature : 7 days at 70°C (158°F)
    Final cure time and temperature: 7 days at 70°C (158°F)
    Special comments: Pre-heat coating and substrate to 120°F - 140°F (49°C - 60°C) prior to
    application. Maintain adequate air circulation and ventilation. During curing period
    atomized air drying system is highly recommended. Following application flush wash the
    pipe with running water for 10 hours. 
[2] Only products bearing the NSF Mark on the product, product packaging, and/or
    documentation shipped with the product are Certified.



Facility : # 2 USA

Protective (Barrier) Materials

    Water Water
  Water Contact Contact Contact
Trade Designation Size Restriction Temp Material

Coatings - Fittings[1] [2] [G]
Royal PC-12 >=3" CLD 23 ASPH
Royal PC-327 >=3" CLD 23 ASPH 

[1] Number of coats: 1-3
    Maximum field use dry film thickness (in mils): 5
    Maximum Thinner:  5% water by volume
    Recoat Cure Time and Temperature: Immediately at 77°F
    Final Cure Time and temperature: 7 days at 77°F
    Special Comments: 40-60% solids.  The emulsion should be preheated to 120°F before
    application.  The substrate should be between 60°F and 180°F prior to coating.  Velocity
    of air flow across coating during cure: 400 linear feet per minute.  Flush wash the pipe
    until the water meets AWWA standards, or flush wash the pipe with running water for 10
    hours.
[2] Only products bearing the NSF mark on the product, product packaging, and/or
    documentation shipped with the product are Certified.
[G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for
    “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state
    laws and the U.S. Safe Drinking Water Act.

Coatings - Pipe[1] [2] [G]
Royal PC-12 >=3" CLD 23 ASPH
Royal PC-327 >=3" CLD 23 ASPH 

[1] Number of coats: 1-3
    Maximum field use dry film thickness (in mils): 5
    Maximum Thinner:  5% water by volume
    Recoat Cure Time and Temperature: Immediately at 77°F
    Final Cure Time and temperature: 7 days at 77°F
    Special Comments: 40-60% solids.  The emulsion should be preheated to 120°F before
    application.  The substrate should be between 60°F and 180°F prior to coating.  Velocity
    of air flow across coating during cure: 400 linear feet per minute.  Flush wash the pipe
    until the water meets AWWA standards, or flush wash the pipe with running water for 10
    hours.
[2] Only products bearing the NSF mark on the product, product packaging, and/or
    documentation shipped with the product are Certified.
[G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for
    “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state
    laws and the U.S. Safe Drinking Water Act.



Facility : Kingman, AZ

Protective (Barrier) Materials

    Water Water
  Water Contact Contact Contact
Trade Designation Size Restriction Temp Material

Coatings - Fittings[1] [2] [G]
Royal PC-12 >=3" CLD 23 ASPH
Royal PC-327 >=3" CLD 23 ASPH 

[1] Number of Coats: 1-3
    Maximum field use dry film thickness (in mils): 5
    Maximum thinner: 5% water by volume
    Recoat cure time and temperature: Immediately at 77°F
    Final cure time and temperature: 7 days at 77°F
    Special comments: 40-60% Solids.  The emulsion should be preheated to 120°F before
    application.  The substrate should be between 60°F and 180°F prior to coating.  Velocity
    of air flow across coating during cure: 400 linear feet per minute.  Flush wash the pipe
    until the water meets AWWA standards, or flush wash the pipe with running water for 10
    hours.
[2] Only products bearing the NSF Mark on the product, product packaging, and/or
    documentation shipped with the product are Certified.
[G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for
    “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state
    laws and the U.S. Safe Drinking Water Act.

Coatings - Pipe[1] [2] [G]
Royal PC-12 >=3" CLD 23 ASPH
Royal PC-327 >=3" CLD 23 ASPH 

[1] Number of Coats: 1-3
    Maximum field use dry film thickness (in mils): 5
    Maximum thinner: 5% water by volume
    Recoat cure time and temperature: Immediately at 77°F
    Final cure time and temperature: 7 days at 77°F
    Special comments: 40-60% Solids.  The emulsion should be preheated to 120°F before
    application.  The substrate should be between 60°F and 180°F prior to coating.  Velocity
    of air flow across coating during cure: 400 linear feet per minute.  Flush wash the pipe
    until the water meets AWWA standards, or flush wash the pipe with running water for 10
    hours.
[2] Only products bearing the NSF Mark on the product, product packaging, and/or
    documentation shipped with the product are Certified.
[G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for
    “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state
    laws and the U.S. Safe Drinking Water Act.



Facility : Kimberton, PA

Protective (Barrier) Materials

    Water Water
  Water Contact Contact Contact
Trade Designation Size Restriction Temp Material

Coatings - Fittings[1] [2] [G]
Royal PC-12 >= 3" CLD 23 ASPH
Royal PC-327 >= 3" CLD 23 ASPH 

[1] Number of Coats: 1-3
    Maximum field use dry film thickness (in mils): 5
    Maximum thinner: 5% water by volume
    Recoat cure time and temperature: Immediately at 77°F
    Final cure time and temperature: 7 days at 77°F
    Special comments: 40-60% Solids.  The emulsion should be preheated to 120F° before
    application.  The substrate should be between 60°F and 180F° prior to coating.  Velocity
    of air flow across coating during cure: 400 linear feet per minute.  Flush wash the pipe
    until the water meets AWWA standards, or flush wash the pipe with running water for 10
    hours.
[2] Only products bearing the NSF Mark on the product, product packaging, and/or
    documentation shipped with the product are Certified.
[G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for
    “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state
    laws and the U.S. Safe Drinking Water Act.

Coatings - Pipe
Royal PC-12[1] [2] [G] >= 3" CLD 23 ASPH
Royal PC-327[1] [2] [G] >= 3" CLD 23 ASPH 

[1] Number of Coats: 1-3
    Maximum field use dry film thickness (in mils): 5
    Maximum thinner: 5% water by volume
    Recoat cure time and temperature: Immediately at 77°F
    Final cure time and temperature: 7 days at 77°F
    Special comments: 40-60% Solids.  The emulsion should be preheated to 120F° before
    application.  The substrate should be between 60°F and 180F° prior to coating.  Velocity
    of air flow across coating during cure: 400 linear feet per minute.  Flush wash the pipe
    until the water meets AWWA standards, or flush wash the pipe with running water for 10
    hours.
[2] Only products bearing the NSF Mark on the product, product packaging, and/or
    documentation shipped with the product are Certified.
[G] Product is Certified to NSF/ANSI 372 and conforms with the lead content requirements for
    “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state
    laws and the U.S. Safe Drinking Water Act.

Number of matching Manufacturers is 1
Number of matching Products is 18
Processing time was 0 seconds