NSF Product and Service Listings

These NSF Official Listings are current as of Friday, December 26, 2025 at 12:15 a.m. Eastern Time. Please contact NSF to confirm the status of any Listing, report errors, or make suggestions.

Alert: NSF is concerned about fraudulent downloading and manipulation of website text. Always confirm this information by clicking on the below link for the most accurate information: http://info.nsf.org/Certified/PwsComponents/Listings.asp?Company=C0379884&Standard=061&


NSF/ANSI/CAN 61
Drinking Water System Components - Health Effects

NOTE: Unless otherwise indicated for Materials, Certification is only for the Water Contact Material shown in the Listing. Click here for a list of Abbreviations used in these Listings. Click here for the definitions of Water Contact Temperatures denoted in these Listings. Products certified to NSF/ANSI/CAN 61 comply with the health effects criteria in NSF/ANSI/CAN 600.

 
Ceme SPA 
Via Dell'industria, 5
27020 Trivolzio, PV 
Italy 
39 0382 18051
Visit this company's website


Facility : Zhongshan, China

Mechanical Plumbing Devices

Trade Designation      

Hot Water Dispenser Components[1] [2] [G]
Series W[Q]       

[Q] This product meets the reduced Q test statistic criteria of 1 ug or 0.5 ug for lead per
    Section 9.5.1.1 of NSF/ANSI/CAN 61.


[1] Valves are named as follows: W A B CDE F G H I WXX, where:
       
    W   -  Series W Valve
    A   -  Inlet
           2 -  MOULD BODY WITH 3/4" INLET, 3/4"(OUTPUT PUSHFIT)
           A -  MOULD WATER VALVE FITTINGS MALE 180°, G 3/4"
           B -  MOULD WATER VALVE FITTINGS MALE 180°, G 1/2"
           C -  MOULD WATER VALVE FITTINGS MALE 180°, G 3/8"
           D -  MOULD WATER VALVE FITTINGS MALE 180° CUSTOMIZE FOR KEURIG 180°, 3/4"
           F -  MOULD WATER VALVE FITTINGS MALE 90°, G 1/2"
           G -  MOULD WATER VALVE FITTINGS MALE 90°, G 3/4"
           0 -  ONLY PILOT, NO BODY
    B   -  Outlet
           2 -  MOULD BODY WITH 3/4" INLET, JG6mm
           3 -  MOULD BODY WITH 3/4" INLET, JG10mm
           4 -  MOULD BODY WITH 3/4" INLET, JG8mm
           7 -  MOULD BODY WITH 3/4" INLET, JG1/4”
           A -  MOULD WATER VALVE FITTINGS MALE 180°, G 3/4"
           B -  MOULD WATER VALVE FITTINGS MALE 180°, G 1/2"
           C -  MOULD WATER VALVE FITTINGS MALE 180°, G 3/8"
           F -  MOULD WATER VALVE FITTINGS MALE 90°, G 1/2"
           0 -  ONLY PILOT, NO BODY
    CDE - DN mm 00,0
           100 -  10 mm
    F   -  FLOW RESTRICTOR
           0 -  WITHOUT
           1 -  (1,2) liters
           2 -  (2,2) liters
    G   -  FLOW REGULATOR
           0 -  WITHOUT
    H   -  FILTER
           0 -  WITHOUT
           1 -  80 mesh
           2 -  150 mesh
           3 -  Check Valve
    I   -  CUSTOMIZATION
    0   -  WITHOUT
           1 -  WITH (SPECIAL EXECUTION)
           3 -  NEEDLE
    WXX - COIL
[2] Series W valves are solenoid valves intended for use with hot water dispensers up to 65
    degrees Celsius.
[G] Product is Certified to NSF/ANSI/CAN 372 and conforms with the lead content requirements
    for "lead free" plumbing as defined by California, Vermont, Maryland, and Louisiana
    state laws and the U.S. Safe Drinking Water Act.

Solenoid Valves[3] [G]
V3 Series[Q]      
V7 Series[Q]      
VD Series[Q]       

[Q] This product meets the reduced Q test statistic criteria of 1 ug or 0.5 ug for lead per
    Section 9.5.1.1 of NSF/ANSI/CAN 61.


[3] Valves are named as follows: VJ XX YY ZZZ P WWW KKKK
                    
    SERIES
      V - Fixed
      J - 3 for 3 way
          7 for 2 way
          D for Dump
                  
    VERSION
      XX - Sequential number for hydraulic connections
           (in V3 models) - 18, 19, 30, 33, 40, 53, 54, 55, 70, 73, 82, 83, 91, 92, 93, 95, 
            97, 99
           (in V7 models) - 19, 30, 31, 39, 40, 42, 43, 44, 45, 70, 82, 91, 93, 95, 99
           (in VD models) - 00, 03
                    
    KIND OF SEALING
      YY - LS for LSR liquid silicone
           VN for Silicone neutral
           EN for EPDM black
                                   
    SEAT DIAMETER - Two or three digits
      ZZ or ZZZ - Internal fluid passage diameter
                  (in V3 models ) - 10, 12, 15, 20, 25, 26, 27
                  (in V7 models) - 10, 12, 15, 20, 25
                  (in VD models) - 100
                               
    BODY TREATMENT
      P - Plastic body
             
    SPECIAL EXECUTION - Not in contact with water
      WWW - In case of NO special execution NO digit
                                    
    STANDARD COIL - Not in contact with water
      KKKK - It depends on type of coil.
[G] Product is Certified to NSF/ANSI/CAN 372 and conforms with the lead content requirements
    for "lead free" plumbing as defined by California, Vermont, Maryland, and Louisiana
    state laws and the U.S. Safe Drinking Water Act.



Facility : Cavenago di Brianza (MB), Italy

Mechanical Plumbing Devices

Trade Designation      

Solenoid Valves[3] [G]
Series L Valves[Q]       

[Q] This product meets the reduced Q test statistic criteria of 1 ug or 0.5 ug for lead per
    Section 9.5.1.1 of NSF/ANSI/CAN 61.


[3] L   - Series L Valve
    AAA - Version
    400 - Body thread M20*1
    500 - Body thread M22*2
    BB  - Seat Diameter
    50  - 5 mm
    CC  - Kind of Seals
    LS  - LSR Liquid Silicone
    P   - Plastic Body
    DD  - Special Execution
    EEE - Coil Type
[G] Product is Certified to NSF/ANSI/CAN 372 and conforms with the lead content requirements
    for "lead free" plumbing as defined by California, Vermont, Maryland, and Louisiana
    state laws and the U.S. Safe Drinking Water Act.

Hot Water Dispenser Components[1] [2] [G]
Series W[Q]       

[Q] This product meets the reduced Q test statistic criteria of 1 ug or 0.5 ug for lead per
    Section 9.5.1.1 of NSF/ANSI/CAN 61.


[1] Valves are named as follows: W A B CDE F G H I WXX, where:
       
    W   -  Series W Valve
    A - Inlet
        2 - MOULD BODY WITH 3/4" INLET, 3/4"(OUTPUT PUSHFIT)
        A - MOULD WATER VALVE FITTINGS MALE 180°, G ¾”
        B - MOULD WATER VALVE FITTINGS MALE 180°, G ½”
        C - MOULD WATER VALVE FITTINGS MALE 180°, G 3/8"
        D - MOULD WATER VALVE FITTINGS MALE 180° CUSTOMIZE FOR KEURIG 180°, 3/4"
        F - MOULD WATER VALVE FITTINGS MALE 90°, G ½”
        G - MOULD WATER VALVE FITTINGS MALE 90°, G ¾”
        L - MOULD WATER VALVE FITTINGS, Push fit Ø6mm
        M - MOULD WATER VALVE FITTINGS, Push fit Ø8mm
        N - MOULD WATER VALVE FITTINGS, Push fit Ø10mm
        P - MOULD WATER VALVE FITTINGS, Push fit Ø1/4”
        R - MOULD WATER VALVE FITTINGS, Push fit Ø3/8”
        0 - ONLY PILOT, NO BODY
    B - Outlet
        2 - MOULD BODY WITH 3/4" INLET, JG6mm
        3 - MOULD BODY WITH 3/4" INLET, JG10mm
        4 - MOULD BODY WITH 3/4" INLET, JG8mm
        7 - MOULD BODY WITH 3/4" INLET, JG1/4”
        A - MOULD WATER VALVE FITTINGS MALE 180°, G 3/4"
        B - MOULD WATER VALVE FITTINGS MALE 180°, G 1/2"
        C - MOULD WATER VALVE FITTINGS MALE 180°, G 3/8"
        F - MOULD WATER VALVE FITTINGS MALE 90°, G 1/2"
        L - MOULD WATER VALVE FITTINGS, Push fit Ø6mm
        M - MOULD WATER VALVE FITTINGS, Push fit Ø8mm
        N - MOULD WATER VALVE FITTINGS, Push fit Ø10mm
        P - MOULD WATER VALVE FITTINGS, Push fit Ø1/4”
        R - MOULD WATER VALVE FITTINGS, Push fit Ø3/8”
        0 - ONLY PILOT, NO BODY
    CDE - DN mm 00,0
           100 -  10 mm
    F   -  FLOW RESTRICTOR
           0 -  WITHOUT
           1 -  (1,2) liters
           2 -  (2,2) liters
    G   -  FLOW REGULATOR
           0 -  WITHOUT
    H   -  FILTER
           0 -  WITHOUT
           1 -  80 mesh
           2 -  150 mesh
           3 -  Check Valve
    I   -  CUSTOMIZATION
           0 -  WITHOUT
           1 -  WITH (SPECIAL EXECUTION
           3 -  NEEDLE
    WXX -  COIL
[2] Series W valves are solenoid valves intended for use with hot water dispensers up to 65
    degrees Celsius.
[G] Product is Certified to NSF/ANSI/CAN 372 and conforms with the lead content requirements
    for "lead free" plumbing as defined by California, Vermont, Maryland, and Louisiana
    state laws and the U.S. Safe Drinking Water Act.



Facility : Inzago, Italy

Mechanical Plumbing Devices

Trade Designation      

Solenoid Valves[1] [G]
V3 Series[Q]      
V7 Series[Q]       

[Q] This product meets the reduced Q test statistic criteria of 1 ug or 0.5 ug for lead per
    Section 9.5.1.1 of NSF/ANSI/CAN 61.


[1] Valves are named as follows: VJ XX YY ZZZ P WWW KKKK
    
    SERIES
    V - Fixed
    J - 3 for 3 way
    7 for 2 way
    
    VERSION
    XX - Sequential number for hydraulic connections
         (in V3 models) - 18, 19, 30, 40, 53, 54, 55, 70, 73, 82, 83, 91, 92, 93, 95, 97, 99
         (in V7 models) - 19, 30, 31, 39, 40, 42, 43, 44, 45, 70, 82, 91, 93, 95, 99
      
    KIND OF SEALING
    YY - LS for LSR liquid silicone
    VN for Silicone neutral
    EN for EPDM black
                      
    SEAT DIAMETER - Two or three digits
    ZZ or ZZZ - Internal fluid passage diameter
                (in V3 models ) - 10, 12, 15, 20, 25, 26, 27
                (in V7 models) - 10, 12, 15, 20, 25
                    
    BODY TREATMENT
    P - Plastic body
    
    SPECIAL EXECUTION - Not in contact with water
    WWW - In case of NO special execution NO digit
                  
    STANDARD COIL - Not in contact with water
    KKKK          - It depends on type of coil.
[G] Product is Certified to NSF/ANSI/CAN 372 and conforms with the lead content requirements
    for "lead free" plumbing as defined by California, Vermont, Maryland, and Louisiana
    state laws and the U.S. Safe Drinking Water Act.

Number of matching Manufacturers is 1
Number of matching Products is 8
Processing time was 0 seconds