NSF Product and Service Listings

These NSF Official Listings are current as of Friday, December 26, 2025 at 12:15 a.m. Eastern Time. Please contact NSF to confirm the status of any Listing, report errors, or make suggestions.

Alert: NSF is concerned about fraudulent downloading and manipulation of website text. Always confirm this information by clicking on the below link for the most accurate information: http://info.nsf.org/Certified/PwsComponents/Listings.asp?Company=C0472654&Standard=061&


NSF/ANSI/CAN 61
Drinking Water System Components - Health Effects

NOTE: Unless otherwise indicated for Materials, Certification is only for the Water Contact Material shown in the Listing. Click here for a list of Abbreviations used in these Listings. Click here for the definitions of Water Contact Temperatures denoted in these Listings. Products certified to NSF/ANSI/CAN 61 comply with the health effects criteria in NSF/ANSI/CAN 600.

 
Kanat Boyacilik Ticaret Ve Sanayi A.S. 
Kemalpasa
OSB Mah. No. 321 
35730 Izmir 
Turkey 
90 232 878 9500
Visit this company's website


Facility : Izmir, Turkey

Protective (Barrier) Materials

    Water Water
  Water Contact Contact Contact
Trade Designation Size Restriction Temp Material

Coatings - Fittings[1]
18530 KANEPOX LINING FREE PRO >= 1" CLD 23 EPOXY 

[1] Colors: Red Oxide
    Number of coats: 1-2
    Maximum field use dry film thickness (in mils): 40 mils
    Recoat cure time and temperature: 6 hours at 25°C
    Final cure time and temperature: 14 days at 25°C
    Special Comments: Mix ratio of Part A:B is 2:1 by volume

Coatings - Fittings[2]
35000 KANPOLY PURCO >= 2.5" D. HOT PUR 

[2] Colors: White
    Number of coats: 1
    Maximum field use dry film thickness (in mils): 60 mils
    Final cure time and temperature: 21 days at 20°C
    Special Comments: Mix ratio of Part A:Part B is 3:1 by volume. Plural component gun
    application is required at a mix ratio of 3:1. Component temperature and pressure = min
    40°C, 250 bar. Line/gun temperature and pressure = min 40°C, 250 bar. Minimum DFT = 20
    mils.

Coatings - Pipe[1]
18530 KANEPOX LINING FREE PRO >= 1" CLD 23 EPOXY 

[1] Colors: Red Oxide
    Number of coats: 1-2
    Maximum field use dry film thickness (in mils): 40 mils
    Recoat cure time and temperature: 6 hours at 25°C
    Final cure time and temperature: 14 days at 25°C
    Special Comments: Mix ratio of Part A:B is 2:1 by volume

Coatings - Pipe[2]
35000 KANPOLY PURCO >= 36" D. HOT PUR 

[2] Colors: White
    Number of coats: 1
    Maximum field use dry film thickness (in mils): 60 mils
    Final cure time and temperature: 21 days at 20°C
    Special Comments: Mix ratio of Part A:Part B is 3:1 by volume. Plural component gun
    application is required at a mix ratio of 3:1. Component temperature and pressure = min
    40°C, 250 bar. Line/gun temperature and pressure = min 40°C, 250 bar. Minimum DFT = 20
    mils.

Coatings - Pump[1]
18530 KANEPOX LINING FREE PRO >= 1" CLD 23 EPOXY 

[1] Colors: Red Oxide
    Number of coats: 1-2
    Maximum field use dry film thickness (in mils): 40 mils
    Recoat cure time and temperature: 6 hours at 25°C
    Final cure time and temperature: 14 days at 25°C
    Special Comments: Mix ratio of Part A:B is 2:1 by volume

Coatings - Tank[1]
18530 KANEPOX LINING FREE PRO >= 100 gal. CLD 23 EPOXY 

[1] Colors: Red Oxide
    Number of coats: 1-2
    Maximum field use dry film thickness (in mils): 40 mils
    Recoat cure time and temperature: 6 hours at 25°C
    Final cure time and temperature: 14 days at 25°C
    Special Comments: Mix ratio of Part A:B is 2:1 by volume

Coatings - Valve[1]
18530 KANEPOX LINING FREE PRO >= 1" CLD 23 EPOXY 

[1] Colors: Red Oxide
    Number of coats: 1-2
    Maximum field use dry film thickness (in mils): 40 mils
    Recoat cure time and temperature: 6 hours at 25°C
    Final cure time and temperature: 14 days at 25°C
    Special Comments: Mix ratio of Part A:B is 2:1 by volume

Coatings - Valve[2]
35000 KANPOLY PURCO >= 2.5" D. HOT PUR 

[2] Colors: White
    Number of coats: 1
    Maximum field use dry film thickness (in mils): 60 mils
    Final cure time and temperature: 21 days at 20°C
    Special Comments: Mix ratio of Part A:Part B is 3:1 by volume. Plural component gun
    application is required at a mix ratio of 3:1. Component temperature and pressure = min
    40°C, 250 bar. Line/gun temperature and pressure = min 40°C, 250 bar. Minimum DFT = 20
    mils.

Number of matching Manufacturers is 1
Number of matching Products is 8
Processing time was 0 seconds