NSF Product and Service Listings

These NSF Official Listings are current as of Friday, December 26, 2025 at 12:15 a.m. Eastern Time. Please contact NSF to confirm the status of any Listing, report errors, or make suggestions.

Alert: NSF is concerned about fraudulent downloading and manipulation of website text. Always confirm this information by clicking on the below link for the most accurate information: http://info.nsf.org/Certified/PwsComponents/Listings.asp?Company=C0547233&Standard=061&


NSF/ANSI/CAN 61
Drinking Water System Components - Health Effects

NOTE: Unless otherwise indicated for Materials, Certification is only for the Water Contact Material shown in the Listing. Click here for a list of Abbreviations used in these Listings. Click here for the definitions of Water Contact Temperatures denoted in these Listings. Products certified to NSF/ANSI/CAN 61 comply with the health effects criteria in NSF/ANSI/CAN 600.

 
Integrity Pump and Motor Group, LLC 
7112 Juniper Road
Fairview, TN 37062 
United States 
615-544-7072
Visit this company's website


Facility : Fairview, TN

Mechanical Devices

    Water Water
    Contact Contact
Trade Designation Size Temp Material

Pumps [G]
O/L Vertical Turbine[1] 7" - 22" CLD 23 MLTPL
W/L Vertical Turbine [1] 7" - 22" CLD 23 MLTPL
XXIYYZZB[2] [3] 1" x 2" - 6" x 10" CLD 23 MLTPL
XXIYYZZC[2] [3] 1" x 2" - 6" x 10" CLD 23 MLTPL
XXIYYZZG[2] [3] 1" x 2" - 6" x 10" CLD 23 MLTPL 

[1] Certified for a minimum daily flow of 36,000 gallons.
[2] The "Size" denotes suction end size x discharge end size.
[3] The variables in the trade name denote the following: 	
    "XX" = discharge size in inches	
    "YY" = suction size in inches (can be one or two digits)	
    "ZZ" = nominal impeller size (can be one or two digits)	
    	
    The options for each variable in each series are as follows: 	
    G Series:	
    Discharge size      Suction size     Nominal impeller size	
    1.5                 2.0              8	
    1.5                 2.0              6	
    1.0                 2.0              7	
    	
    B Series: 	
    Discharge size      Suction size     Nominal impeller size	
    2.5                 3.0              7	
    3.0                 4.0              7	
    4.0                 5.0              7	
    	
    C Series:	
    Discharge size      Suction size     Nominal impeller size	
    4.0                 6.0              13	
    5.0                 8.0              14	
    6.0                 10.0             14	
[G] Product is Certified to NSF/ANSI/CAN 372 and conforms with the lead content requirements
    for "lead free" plumbing as defined by California, Vermont, Maryland, and Louisiana
    state laws and the U.S. Safe Drinking Water Act.

Submersible Pump - Pump Ends[1] [G]
Submersible Turbine 7" - 14" CLD 23 MLTPL 

[1] Certified for a minimum daily flow of 36,000 gallons.
[G] Product is Certified to NSF/ANSI/CAN 372 and conforms with the lead content requirements
    for "lead free" plumbing as defined by California, Vermont, Maryland, and Louisiana
    state laws and the U.S. Safe Drinking Water Act.

Number of matching Manufacturers is 1
Number of matching Products is 6
Processing time was 0 seconds