NSF Product and Service Listings

These NSF Official Listings are current as of Sunday, December 7, 2025 at 12:15 a.m. Eastern Time. Please contact NSF to confirm the status of any Listing, report errors, or make suggestions.

Alert: NSF is concerned about fraudulent downloading and manipulation of website text. Always confirm this information by clicking on the below link for the most accurate information: http://info.nsf.org/Certified/PwsComponents/Listings.asp?Company=C0686872&Standard=061&


NSF/ANSI/CAN 61
Drinking Water System Components - Health Effects

NOTE: Unless otherwise indicated for Materials, Certification is only for the Water Contact Material shown in the Listing. Click here for a list of Abbreviations used in these Listings. Click here for the definitions of Water Contact Temperatures denoted in these Listings. Products certified to NSF/ANSI/CAN 61 comply with the health effects criteria in NSF/ANSI/CAN 600.

 
Denso North America 
9710 Telge Road
Houston, TX 77095 
United States 
281-821-3355
Visit this company's website


Facility : Houston, TX

Protective (Barrier) Materials

    Water Water
  Water Contact Contact Contact
Trade Designation Size Restriction Temp Material

Coatings - Fittings[1] [G]
Archco 426 >= 6" CLD 23 EPOXY 

[1] Colors: White, Gray, Blue										
    Number of Coats: 1-2										
    Maximum field use dry film thickness (in mils): 28										
    Maximum Thinner: 5% Isopropyl Alcohol										
    Recoat cure time and temperature: 8 hour at 25°C (77°F)										
    Final cure time and temperature: 7 days at 25°C (77°F)										
    Special comments: Separately agitate Part A (base) and Part B (catalyst) with power
    agitator prior to combining. Once combined mix thoroughly with power agitator.										
    Surface must be at least 50°F (10°C) prior to application. Surfaces must be dry, clean,
    free of oil, grease, and other contaminants and structurally sound. 										
    Mix ratio of Part A:B is 1:1 by volume. Can be applied with spray equipment, roller, or
    hand brushed. One coat application 24-28 mils wet film thickness. Two coat
    application										
    12-14 mils wet film thickness per coat to a maximum of 28 mils wet film thickness.
[G] Product is Certified to NSF/ANSI/CAN 372 and conforms with the lead content requirements
    for "lead free" plumbing as defined by California, Vermont, Maryland, and Louisiana
    state laws and the U.S. Safe Drinking Water Act.

Coatings - Pipe[1] [G]
Archco 426 >= 72" CLD 23 EPOXY 

[1] Colors: White, Gray, Blue										
    Number of Coats: 1-2										
    Maximum field use dry film thickness (in mils): 28										
    Maximum Thinner: 5% Isopropyl Alcohol										
    Recoat cure time and temperature: 8 hour at 25°C (77°F)										
    Final cure time and temperature: 7 days at 25°C (77°F)										
    Special comments: Separately agitate Part A (base) and Part B (catalyst) with power
    agitator prior to combining. Once combined mix thoroughly with power agitator.										
    Surface must be at least 50°F (10°C) prior to application. Surfaces must be dry, clean,
    free of oil, grease, and other contaminants and structurally sound. 										
    Mix ratio of Part A:B is 1:1 by volume. Can be applied with spray equipment, roller, or
    hand brushed. One coat application 24-28 mils wet film thickness. Two coat
    application										
    12-14 mils wet film thickness per coat to a maximum of 28 mils wet film thickness.
[G] Product is Certified to NSF/ANSI/CAN 372 and conforms with the lead content requirements
    for "lead free" plumbing as defined by California, Vermont, Maryland, and Louisiana
    state laws and the U.S. Safe Drinking Water Act.

Coatings - Pump[1] [G]
Archco 426 >= 6" CLD 23 EPOXY 

[1] Colors: White, Gray, Blue										
    Number of Coats: 1-2										
    Maximum field use dry film thickness (in mils): 28										
    Maximum Thinner: 5% Isopropyl Alcohol										
    Recoat cure time and temperature: 8 hour at 25°C (77°F)										
    Final cure time and temperature: 7 days at 25°C (77°F)										
    Special comments: Separately agitate Part A (base) and Part B (catalyst) with power
    agitator prior to combining. Once combined mix thoroughly with power agitator.										
    Surface must be at least 50°F (10°C) prior to application. Surfaces must be dry, clean,
    free of oil, grease, and other contaminants and structurally sound. 										
    Mix ratio of Part A:B is 1:1 by volume. Can be applied with spray equipment, roller, or
    hand brushed. One coat application 24-28 mils wet film thickness. Two coat
    application										
    12-14 mils wet film thickness per coat to a maximum of 28 mils wet film thickness.
[G] Product is Certified to NSF/ANSI/CAN 372 and conforms with the lead content requirements
    for "lead free" plumbing as defined by California, Vermont, Maryland, and Louisiana
    state laws and the U.S. Safe Drinking Water Act.

Coatings - Tank[1] [G]
Archco 426 >= 10,000 gal. CLD 23 EPOXY 

[1] Colors: White, Gray, Blue										
    Number of Coats: 1-2										
    Maximum field use dry film thickness (in mils): 28										
    Maximum Thinner: 5% Isopropyl Alcohol										
    Recoat cure time and temperature: 8 hour at 25°C (77°F)										
    Final cure time and temperature: 7 days at 25°C (77°F)										
    Special comments: Separately agitate Part A (base) and Part B (catalyst) with power
    agitator prior to combining. Once combined mix thoroughly with power agitator.										
    Surface must be at least 50°F (10°C) prior to application. Surfaces must be dry, clean,
    free of oil, grease, and other contaminants and structurally sound. 										
    Mix ratio of Part A:B is 1:1 by volume. Can be applied with spray equipment, roller, or
    hand brushed. One coat application 24-28 mils wet film thickness. Two coat
    application										
    12-14 mils wet film thickness per coat to a maximum of 28 mils wet film thickness.
[G] Product is Certified to NSF/ANSI/CAN 372 and conforms with the lead content requirements
    for "lead free" plumbing as defined by California, Vermont, Maryland, and Louisiana
    state laws and the U.S. Safe Drinking Water Act.

Coatings - Valve[1] [G]
Archco 426 >= 6" CLD 23 EPOXY 

[1] Colors: White, Gray, Blue										
    Number of Coats: 1-2										
    Maximum field use dry film thickness (in mils): 28										
    Maximum Thinner: 5% Isopropyl Alcohol										
    Recoat cure time and temperature: 8 hour at 25°C (77°F)										
    Final cure time and temperature: 7 days at 25°C (77°F)										
    Special comments: Separately agitate Part A (base) and Part B (catalyst) with power
    agitator prior to combining. Once combined mix thoroughly with power agitator.										
    Surface must be at least 50°F (10°C) prior to application. Surfaces must be dry, clean,
    free of oil, grease, and other contaminants and structurally sound. 										
    Mix ratio of Part A:B is 1:1 by volume. Can be applied with spray equipment, roller, or
    hand brushed. One coat application 24-28 mils wet film thickness. Two coat
    application										
    12-14 mils wet film thickness per coat to a maximum of 28 mils wet film thickness.
[G] Product is Certified to NSF/ANSI/CAN 372 and conforms with the lead content requirements
    for "lead free" plumbing as defined by California, Vermont, Maryland, and Louisiana
    state laws and the U.S. Safe Drinking Water Act.

Number of matching Manufacturers is 1
Number of matching Products is 5
Processing time was 0 seconds