NSF Product and Service Listings

These NSF Official Listings are current as of Friday, December 26, 2025 at 12:15 a.m. Eastern Time. Please contact NSF to confirm the status of any Listing, report errors, or make suggestions.

Alert: NSF is concerned about fraudulent downloading and manipulation of website text. Always confirm this information by clicking on the below link for the most accurate information: http://info.nsf.org/Certified/PwsComponents/Listings.asp?Company=C0842804&Standard=061&


NSF/ANSI/CAN 61
Drinking Water System Components - Health Effects

NOTE: Unless otherwise indicated for Materials, Certification is only for the Water Contact Material shown in the Listing. Click here for a list of Abbreviations used in these Listings. Click here for the definitions of Water Contact Temperatures denoted in these Listings. Products certified to NSF/ANSI/CAN 61 comply with the health effects criteria in NSF/ANSI/CAN 600.

 
Axalta Coating Systems Mexico S de RL de CV 
Av. Industria Eléctrica de México 10
Tlalnepantla 
54015 
Mexico 
800-841-6908 
52 55 5366 3345
Visit this company's website


Facility : # 1 USA

Protective (Barrier) Materials

    Water Water
  Water Contact Contact Contact
Trade Designation Size Restriction Temp Material

Coatings - Fittings[1]
Corlar 7.1T Epóxico Fenalcamina[2] >= 1/2" CLD 23 EPOXY
Corlar 7.1T Epóxico Fenalcamina[3] [4] >= 3/4" CLD 23 EPOXY
Corlar 7.3T Epóxico Poliamina Mod.[5] [6] >= 6" CLD 23 EPOXY 

[1] Meets the health effects requirements of NSF/ANSI/CAN 600 according to the requirements
    of NSF/ANSI/CAN 61 including the most current health effects criteria for xylenes,
    toluene, and ethylbenzene.
[2] Coating Notes:
    Colors: White, Black, Gray, Blue, Beige
    Number Of Coats: 2
    Maximum Field Use Dry Thickness(in mils): 20 mils
    Maximum Thinner: None
    Recoat Cure Time and Temperature: 16 hours at 75°F
    Final Cure Time/Temperature: 30 days at 75°F
    Special Comments: Mix ratio of A:B is 2:1 by volume. This is for pipe, fitting, pump,
    and valve end use.
[3] Coating Notes:
    Colors: White, Black, Gray, Blue, Beige
    Number Of Coats: 1-3
    Maximum Field Use Dry Thickness(in mils): 20
    Maximum Thinner: 5% 71T104 Thinner Clear by volume
    Recoat Cure Time and Temperature: 8 hours at 75°F
    Final Cure Time/Temperature: 7 days at 75°F
    Special Comments: Mix ratio of A:B is 2:1 by volume.
[4] Certified for mechanical device end use (other than pump and valve) for a maximum of 189
    sq. ft. per gpm.
[5] Coating Notes:
    Colors: White, Beige, Blue
    Number Of Coats: 1-2
    Maximum Field Use Dry Thickness(in mils): 50
    Maximum Thinner: 5% Thinner #2
    Recoat Cure Time and Temperature: 16 hours at 75°F
    Final Cure Time/Temperature: 5 days at 75°F
    Special Comments: Mix ratio of Part A to Part B is 1:1 by volume.
[6] Certified for mechanical device end use (other than pump and valve) for a maximum of 249
    sq. ft. per gpm.

Coatings - Mechanical Devices[1]
Corlar 7.1T Epóxico Fenalcamina[3] [4] CLD 23 EPOXY
Corlar 7.3T Epóxico Poliamina Mod.[5] [6] CLD 23 EPOXY 

[1] Meets the health effects requirements of NSF/ANSI/CAN 600 according to the requirements
    of NSF/ANSI/CAN 61 including the most current health effects criteria for xylenes,
    toluene, and ethylbenzene.
[3] Coating Notes:
    Colors: White, Black, Gray, Blue, Beige
    Number Of Coats: 1-3
    Maximum Field Use Dry Thickness(in mils): 20
    Maximum Thinner: 5% 71T104 Thinner Clear by volume
    Recoat Cure Time and Temperature: 8 hours at 75°F
    Final Cure Time/Temperature: 7 days at 75°F
    Special Comments: Mix ratio of A:B is 2:1 by volume.
[4] Certified for mechanical device end use (other than pump and valve) for a maximum of 189
    sq. ft. per gpm.
[5] Coating Notes:
    Colors: White, Beige, Blue
    Number Of Coats: 1-2
    Maximum Field Use Dry Thickness(in mils): 50
    Maximum Thinner: 5% Thinner #2
    Recoat Cure Time and Temperature: 16 hours at 75°F
    Final Cure Time/Temperature: 5 days at 75°F
    Special Comments: Mix ratio of Part A to Part B is 1:1 by volume.
[6] Certified for mechanical device end use (other than pump and valve) for a maximum of 249
    sq. ft. per gpm.

Coatings - Pipe[1]
Corlar 7.1T Epóxico Fenalcamina[2] >= 18" CLD 23 EPOXY
Corlar 7.3T Epóxico Poliamina Mod.[5] [6] >= 24" CLD 23 EPOXY 

[1] Meets the health effects requirements of NSF/ANSI/CAN 600 according to the requirements
    of NSF/ANSI/CAN 61 including the most current health effects criteria for xylenes,
    toluene, and ethylbenzene.
[2] Coating Notes:
    Colors: White, Black, Gray, Blue, Beige
    Number Of Coats: 2
    Maximum Field Use Dry Thickness(in mils): 20 mils
    Maximum Thinner: None
    Recoat Cure Time and Temperature: 16 hours at 75°F
    Final Cure Time/Temperature: 30 days at 75°F
    Special Comments: Mix ratio of A:B is 2:1 by volume. This is for pipe, fitting, pump,
    and valve end use.
[5] Coating Notes:
    Colors: White, Beige, Blue
    Number Of Coats: 1-2
    Maximum Field Use Dry Thickness(in mils): 50
    Maximum Thinner: 5% Thinner #2
    Recoat Cure Time and Temperature: 16 hours at 75°F
    Final Cure Time/Temperature: 5 days at 75°F
    Special Comments: Mix ratio of Part A to Part B is 1:1 by volume.
[6] Certified for mechanical device end use (other than pump and valve) for a maximum of 249
    sq. ft. per gpm.

Coatings - Pump[1]
Corlar 7.1T Epóxico Fenalcamina[3] [4] >= 4" CLD 23 EPOXY
Corlar 7.1T Epóxico Fenalcamina[2] >= 1/2" CLD 23 EPOXY
Corlar 7.3T Epóxico Poliamina Mod.[5] [6] >= 4" CLD 23 EPOXY 

[1] Meets the health effects requirements of NSF/ANSI/CAN 600 according to the requirements
    of NSF/ANSI/CAN 61 including the most current health effects criteria for xylenes,
    toluene, and ethylbenzene.
[2] Coating Notes:
    Colors: White, Black, Gray, Blue, Beige
    Number Of Coats: 2
    Maximum Field Use Dry Thickness(in mils): 20 mils
    Maximum Thinner: None
    Recoat Cure Time and Temperature: 16 hours at 75°F
    Final Cure Time/Temperature: 30 days at 75°F
    Special Comments: Mix ratio of A:B is 2:1 by volume. This is for pipe, fitting, pump,
    and valve end use.
[3] Coating Notes:
    Colors: White, Black, Gray, Blue, Beige
    Number Of Coats: 1-3
    Maximum Field Use Dry Thickness(in mils): 20
    Maximum Thinner: 5% 71T104 Thinner Clear by volume
    Recoat Cure Time and Temperature: 8 hours at 75°F
    Final Cure Time/Temperature: 7 days at 75°F
    Special Comments: Mix ratio of A:B is 2:1 by volume.
[4] Certified for mechanical device end use (other than pump and valve) for a maximum of 189
    sq. ft. per gpm.
[5] Coating Notes:
    Colors: White, Beige, Blue
    Number Of Coats: 1-2
    Maximum Field Use Dry Thickness(in mils): 50
    Maximum Thinner: 5% Thinner #2
    Recoat Cure Time and Temperature: 16 hours at 75°F
    Final Cure Time/Temperature: 5 days at 75°F
    Special Comments: Mix ratio of Part A to Part B is 1:1 by volume.
[6] Certified for mechanical device end use (other than pump and valve) for a maximum of 249
    sq. ft. per gpm.

Coatings - Tank[1]
Corlar 7.1T Epóxico Fenalcamina[3] [4] >= 1500 gal. CLD 23 EPOXY
Corlar 7.3T Epóxico Poliamina Mod.[5] [6] >= 700 gal. CLD 23 EPOXY 

[1] Meets the health effects requirements of NSF/ANSI/CAN 600 according to the requirements
    of NSF/ANSI/CAN 61 including the most current health effects criteria for xylenes,
    toluene, and ethylbenzene.
[3] Coating Notes:
    Colors: White, Black, Gray, Blue, Beige
    Number Of Coats: 1-3
    Maximum Field Use Dry Thickness(in mils): 20
    Maximum Thinner: 5% 71T104 Thinner Clear by volume
    Recoat Cure Time and Temperature: 8 hours at 75°F
    Final Cure Time/Temperature: 7 days at 75°F
    Special Comments: Mix ratio of A:B is 2:1 by volume.
[4] Certified for mechanical device end use (other than pump and valve) for a maximum of 189
    sq. ft. per gpm.
[5] Coating Notes:
    Colors: White, Beige, Blue
    Number Of Coats: 1-2
    Maximum Field Use Dry Thickness(in mils): 50
    Maximum Thinner: 5% Thinner #2
    Recoat Cure Time and Temperature: 16 hours at 75°F
    Final Cure Time/Temperature: 5 days at 75°F
    Special Comments: Mix ratio of Part A to Part B is 1:1 by volume.
[6] Certified for mechanical device end use (other than pump and valve) for a maximum of 249
    sq. ft. per gpm.

Coatings - Valve[1]
Corlar 7.1T Epóxico Fenalcamina[3] [4] >= 4" CLD 23 EPOXY
Corlar 7.1T Epóxico Fenalcamina[2] >= 1/2" CLD 23 EPOXY
Corlar 7.3T Epóxico Poliamina Mod.[5] [6] >= 4" CLD 23 EPOXY 

[1] Meets the health effects requirements of NSF/ANSI/CAN 600 according to the requirements
    of NSF/ANSI/CAN 61 including the most current health effects criteria for xylenes,
    toluene, and ethylbenzene.
[2] Coating Notes:
    Colors: White, Black, Gray, Blue, Beige
    Number Of Coats: 2
    Maximum Field Use Dry Thickness(in mils): 20 mils
    Maximum Thinner: None
    Recoat Cure Time and Temperature: 16 hours at 75°F
    Final Cure Time/Temperature: 30 days at 75°F
    Special Comments: Mix ratio of A:B is 2:1 by volume. This is for pipe, fitting, pump,
    and valve end use.
[3] Coating Notes:
    Colors: White, Black, Gray, Blue, Beige
    Number Of Coats: 1-3
    Maximum Field Use Dry Thickness(in mils): 20
    Maximum Thinner: 5% 71T104 Thinner Clear by volume
    Recoat Cure Time and Temperature: 8 hours at 75°F
    Final Cure Time/Temperature: 7 days at 75°F
    Special Comments: Mix ratio of A:B is 2:1 by volume.
[4] Certified for mechanical device end use (other than pump and valve) for a maximum of 189
    sq. ft. per gpm.
[5] Coating Notes:
    Colors: White, Beige, Blue
    Number Of Coats: 1-2
    Maximum Field Use Dry Thickness(in mils): 50
    Maximum Thinner: 5% Thinner #2
    Recoat Cure Time and Temperature: 16 hours at 75°F
    Final Cure Time/Temperature: 5 days at 75°F
    Special Comments: Mix ratio of Part A to Part B is 1:1 by volume.
[6] Certified for mechanical device end use (other than pump and valve) for a maximum of 249
    sq. ft. per gpm.

Number of matching Manufacturers is 1
Number of matching Products is 15
Processing time was 0 seconds