NSF Product and Service Listings

[1] Mix ratio of Part A:Part B is 1:1

[1] Certified for a maximum surface area to volume ratio of 0.3 sq. in./L in pipe or 1% of a
    20,000 gallon tank.
[2] To obtain the proper mix, use at least a 3/4" length, but no more than 1/3 of a full
    stick, of product which has been cut with a knife. Product must be mixed for 60-90
    seconds.
[G] Product is Certified to NSF/ANSI/CAN 372 and conforms with the lead content requirements
    for "lead free" plumbing as defined by California, Vermont, Maryland, and Louisiana
    state laws and the U.S. Safe Drinking Water Act.

[1] Certified for use as an anchoring adhesive for installing thread rods (less than or
    equal to 1.3 inches in diameter) in concrete or masonry for water treatment applications.

[1] Certified for use as an anchoring adhesive for installing thread rods (less than or
    equal to 1.3 inches in diameter) in concrete or masonry for water treatment applications.

[1] Certified for use in 45 mm pipe and greater.

[1] Certified for use as an anchoring adhesive for installing thread rods (less than or
    equal to 1.3 inches in diameter) in concrete or masonry for water treatment applications.

[1] Certified or use as an anchoring adhesive for installing thread rods (less than or equal
    to 1.3 inches in diameter) in concrete or masonry for water treatment applications.

[1] The exposed surface area of each sealant in a household distribution system shall not
    exceed 1.3 sq. cm/L or .2 sq. in./L.

[1] The exposed surface area of each sealant in a household distribution system shall not
    exceed 1.3 sq. cm/L or .2 sq. in./L.
[G] Product is Certified to NSF/ANSI/CAN 372 and conforms with the lead content requirements
    for "lead free" plumbing as defined by California, Vermont, Maryland, and Louisiana
    state laws and the U.S. Safe Drinking Water Act.

[2] Certified for use as an anchoring adhesive for installing threaded rods (less than or
    equal to 6 mm - 36mm in diameter) in concrete for water treatment applications.

[1] Mix ratio of Part A:Part B is 1 : 1
[2] The exposed surface area of sealant in a tank shall not exceed 1.3 sq. cm/L or 0.2 sq.
    in./L

[1] Product is Certified for use as an anchoring adhesive for installing threaded rods (less
    than or equal to 1.3 inches in diameter) in concrete for water treatment applications.
[2] Certified for use as an anchoring adhesive for installing threaded rods (less than or
    equal to 24 mm in diameter) in concrete or masonry for water treatment applications. 
    Mix ratio of Part A:Part B is 3:1 by volume.
[3] Certified for use as an anchoring adhesive for installing threaded rods in concrete or
    masonry for water treatment applications. Certified for a maximum surface area to volume
    ratio of 0.00006 sq. in./L
[4] Certified for use as an anchoring adhesive for installing threaded rods (less than or
    equal to 40 mm in diameter) in concrete for water treatment applications.
[5] Certified for use as an anchoring adhesive for installing threaded rods (less than or
    equal to 32 mm in diameter) in concrete for water treatment applications.
[6] Certified for use as an anchoring adhesive for installing screw anchors in concrete for
    water treatment applications. KHC is certified for use with screw anchors less than or
    equal to 20 mm in diameter. HUS4-MAX is certified for use with screw anchors less than
    or equal to 16 mm in diameter.

[1] The exposed surface area of each sealant in a household distribution system should not
    exceed 1.3 sq. cm./L or 0.2 sq. in./L.

[1] Certified for use as an anchoring adhesive for installing thread rods (less than or
    equal
    to 1.3 inches in diameter) in concrete or masonry for water treatment applications.

[1] Certified for use at a maximum surface area to volume ratio of 0.0005 square inches per
    liter in a tank.

[1] Certified for use at a maximum surface area to volume ratio of 0.0005 square inches per
    liter in a tank.

[1] Mix ratio of Part A:Part B is 1:1

[1] Mix ratio of Part A:Part B is 1:1
[2] The exposed surface area of sealant in a tank shall not exceed 0.60 sq. cm/L or 0.095
    sq. in./L
[3] The exposed surface area of sealant in pipes and fittings shall not exceed 1.3 sq. cm/L
    or 0.2 sq. in./L

[G] Product is Certified to NSF/ANSI/CAN 372 and conforms with the lead content requirements
    for "lead free" plumbing as defined by California, Vermont, Maryland, and Louisiana
    state laws and the U.S. Safe Drinking Water Act.

[1] Digits next to the trade name refers to the product volume in (ml).
[2] Certified for use as an anchoring adhesive for installing thread rods (less than or
    equal to 1.3 inches in diameter) in concrete or masonry for water treatment applications.

[1] Certified for use as an anchoring adhesive for installing thread rods (less than or
    equal to 1.3 inches in diameter) in concrete or masonry for water treatment applications.

[1] Certified for a maximum surface area to volume ratio of 0.3 sq. in./L in pipe or 1% of a
    20,000 gallon tank.
[2] To obtain the proper mix, use at least a 3/4" length, but no more than 1/3 of a full
    stick, of product which has been cut with a knife. Product must be mixed for 60-90
    seconds.
[G] Product is Certified to NSF/ANSI/CAN 372 and conforms with the lead content requirements
    for "lead free" plumbing as defined by California, Vermont, Maryland, and Louisiana
    state laws and the U.S. Safe Drinking Water Act.

[1] Mix ratio of Part A:Part B is 1:1
[2] The exposed surface area of sealant in pipes and fittings shall not exceed 1.3 sq. cm/L
    or 0.2 sq. in./L
[3] The exposed surface area of sealant in a tank shall not exceed 1.3 sq. cm/L or 0.2 sq.
    in./L

[1] 8000 Series Adhesive and Hardener includes the following trade names: DS-8014, DS-8024,
    DS-8069, DS-8071, DS-8088-S, DS-8088-L, and DS-8069-C.
[2] Mix ratio is 7.6:1 (A:B) by weight but will vary slightly based on the kit size. 
    Minimum cure time is 1 hour at 100° F.  Please follow the manufacturer’s instructions
    supplied with each kit.
[3] Mix ratio is 3.2:1 (A:B) by weight.  Minimum cure time is 1 hour at 100° F.  The mix
    ratios will vary slightly based on the kit size.  Please follow the manufacturer’s
    instructions supplied with each kit.
[4] Mix ratio is 3.2:1 (A:B) by weight.  Minimum cure time is 1 hour at 110° F.  The mix
    ratios will vary slightly based on the kit size.  Please follow the manufacturer’s
    instructions supplied with each kit.
[5] Mix ratio of adhesive to hardener is 100:26.62 (A:B) by weight. Minimum cure time is 35
    minutes at 77° F. Please follow the manufacturer’s instructions supplied with each kit.
[6] Mix ratio is 3.2:1 (A:B) by weight.  Minimum cure time is 3 hours at 100° F.  The mix
    ratios will vary slightly based on the kit size.  Please follow the manufacturer’s
    instructions supplied with each kit.
[7] Mix ratio is 45:1 (A:B) by weight.  Minimum cure time is 24 hours at 71 - 100° F.  The
    mix ratios will vary slightly based on the kit size.  Please follow the manufacturer’s
    instructions supplied with each kit.

[1] Certified for use as an anchoring adhesive for installing thread rods (less than or
    equal to 1.3 inches in diameter) in concrete or masonry for water treatment applications.

[1] Certified for a maximum surface area to volume ratio of 0.3 sq. in./L in pipe or 1% of a
    20,000 gallon tank.
[2] To obtain the proper mix, use at least a 3/4" length, but no more than 1/3 of a full
    stick, of product which has been cut with a knife. Product must be mixed for 60-90
    seconds.
[G] Product is Certified to NSF/ANSI/CAN 372 and conforms with the lead content requirements
    for "lead free" plumbing as defined by California, Vermont, Maryland, and Louisiana
    state laws and the U.S. Safe Drinking Water Act.

[1] Certified for use as an anchoring adhesive for installing thread rods (less than or
    equal to 1.3 inches in diameter) in concrete or masonry for water treatment applications.

[1] Certified for a maximum exposed surface area of 216 sq. in./1000 gal.

[1] Certified for a maximum exposed surface area of 216 sq. in./1000 gal.
[2] Certified for a maximum surface area of 568 square inches per 1000 gallons.  Mix ratio
    2:1 (Resin:Cure).

[1] Certified for use as an anchoring adhesive for installing thread rods (less than or
    equal to 1.3 inches in diameter) in concrete or masonry for water treatment applications.

[1] Certified for use as an anchoring adhesive for installing thread rods (less than or
    equal to 1.3 inches in diameter) in concrete or masonry for water treatment applications.

[1] Certified for a maximum surface area to volume ratio of 0.3 sq. in./L in pipe or 1% of a
    20,000 gallon tank.
[2] To obtain the proper mix, use at least a 3/4" length, but no more than 1/3 of a full
    stick, of product which has been cut with a knife.  Product must be mixed for 60-90
    seconds.
[G] Product is Certified to NSF/ANSI/CAN 372 and conforms with the lead content requirements
    for "lead free" plumbing as defined by California, Vermont, Maryland, and Louisiana
    state laws and the U.S. Safe Drinking Water Act.

[1] Product is a two part adhesive mixed at a ratio of 2 part A to 1 part B by volume.					
    Adhesive cure time is 60 minutes at 70F					
    Following cure, product must be flushed with ambient temperature tap water for 1 hour. 
[2] Certified for use in immediate return to service pipe liner 4" and greater at a surface
    area to volume ratio of 0.08 in2/L.

[1] Certified for use as an anchoring adhesive for installing thread rods (less than or
    equal to 1.3 inches in diameter) in concrete or masonry for water treatment applications.

[1] Certified for use as an anchoring adhesive for installing thread rods (less than or
    equal to 1.3 inches in diameter) in concrete or masonry for water treatment applications.

[1] The exposed surface area of each sealant in a household distribution system shall not
    exceed 1.3 sq. cm/L or .2 sq. in./L

[1] The exposed surface area of each sealant in a household distribution system shall not
    exceed 1.3 sq. cm/L or .2 sq. in./L
[G] Product is Certified to NSF/ANSI/CAN 372 and conforms with the lead content requirements
    for "lead free" plumbing as defined by California, Vermont, Maryland, and Louisiana
    state laws and the U.S. Safe Drinking Water Act.

[1] Certified for use as an anchoring adhesive for installing thread rods (less than or
    equal to 1.3 inches in diameter) in concrete or masonry for water treatment applications.