NSF Product and Service Listings

[1] This product has also been evaluated for use in Mechanical Plumbing Device applications
    with a maximum use restriction of 2.0 square inches/L.
[2] Certified for a maximum surface area to volume ration of 2.0 square inches/L.
[G] Product is Certified to NSF/ANSI/CAN 372 and conforms with the lead content requirements
    for "lead free" plumbing as defined by California, Vermont, Maryland, and Louisiana
    state laws and the U.S. Safe Drinking Water Act.

[1] This product has also been evaluated for use in Mechanical Plumbing Device applications
    with a maximum use restriction of 2.0 square inches/L.
[2] Certified for a maximum surface area to volume ration of 2.0 square inches/L.
[G] Product is Certified to NSF/ANSI/CAN 372 and conforms with the lead content requirements
    for "lead free" plumbing as defined by California, Vermont, Maryland, and Louisiana
    state laws and the U.S. Safe Drinking Water Act.

[1] Saddle PN25
    SDL 6320 (63 x 20 mm)
    SDL 6325 (63 x 25 mm)
    SDL 6332 (63 x 32 mm)
    SDL 7520 (75 x 20 mm)
    SDL 7525 (75 x 25 mm)
    SDL 7532 (75 x 32 mm)
    SDL 9025 (90 x 25 mm)
    SDL 9032 (90 x 32 mm)
    SDL 9040 (90 x 40 mm)
    SDL 11032 (110 x 32 mm)
    SDL 11040 (110 x 40 mm)
    SDL 11050 (110 x 50 mm)
    SDL 12540 (125 x 40 mm)
    SDL 12550 (125 x 50 mm)
    SDL 12563 (125 x 63 mm)
    SDL 16040 (160 x 40 mm)
    SDL 16050 (160 x 50 mm)
    SDL 16063 (160 x 63 mm)
    SDL 20050 (200 x 50 mm)
    SDL 20063 (200 x 63 mm)
    SDL 20075 (200 x 75 mm)
    SDL 20090 (200 x 90 mm)
    SDL 25063 (250 x 63 mm)
    SDL 25075 (250 x 75 mm)
    SDL 25090 (250 x 90 mm)
    SDL 250110 (250 x 110 mm)
       
    Threaded Saddle PN25
    SDF 6320 (63 mm x 1/2")
    SDF 6325 (63 mm x 3/4")
    SDF 7520 (75 mm x 1/2")
    SDF 7525 (75 mm x 3/4")
    SDF 9020 (90 mm x 1/2")
    SDF 9025 (90 mm x 3/4")
    SDF 11020 (110 mm x 1/2")
    SDF 11025 (110 mm x 3/4")
    SDF 11032 (110 mm x 1")
[G] Product is Certified to NSF/ANSI/CAN 372 and conforms with the lead content requirements
    for "lead free" plumbing as defined by California, Vermont, Maryland, and Louisiana
    state laws and the U.S. Safe Drinking Water Act.

[1] Configurations include:
        
    Swan Neck PN20
    SOP 20 A20 (20 x 20 mm)
    SOP 25 A20 (25 x 25 mm)
    SOP 32 A20 (32 x 32 mm)
         
    Swan Neck Female - Female PN25
    SFF 2020 (20 x 20 mm)
    SFF 2525 (25 x 25 mm)
      
    Swan Neck Short Female - Female PN25
    SFC 2020 (20 x 20 mm)
    SFC 2525 (25 x 25 mm) 
       
    Socket PN25
    MAN 20 (20 x 20 mm)
    MAN 25 (25 x 25 mm)
    MAN 32 (32 x 32 mm)
    MAN 40 (40 x 40 mm)
    MAN 50 (50 x 50 mm)
    MAN 63 (63 x 63 mm)
    MAN 75 (75 x 75 mm)
    MAN 90 (90 x 90 mm)
    MAN 110 (110 x 110 mm)
    MAN 125 (125 x 125 mm)
    MAN 160 (160 x 160 mm)
    
    90° Elbow PN25
    CUV 20 (20 x 20 mm)
    CUV 25 (25 x 25 mm)
    CUV 32 (32 x 32 mm)
    CUV 40 (40 x 40 mm)
    CUV 50 (50 x 50 mm)
    CUV 63 (63 x 63 mm)
    CUV 75 (75 x 75 mm)
    CUV 90 (90 x 90 mm)
    CUV 110 (110 x 110 mm)
    CUV 125 (125 x 125 mm)
    CUV 160 (160 x 160 mm)
    CUV 160 T (160 x 160 mm)
    CUV 200 T (200 x 200 mm)
    CUV 250 T (250 x 250 mm)
        
    45° Elbow PN25
    CUQ 20 (20 x 20 mm)
    CUQ 25 (25 x 25 mm)
    CUQ 32 (32 x 32 mm)
    CUQ 40 (40 x 40 mm)
    CUQ 50 (50 x 50 mm)
    CUQ 63 (63 x 63 mm)
    CUQ 75 (75 x 75 mm)
    CUQ 90 (90 x 90 mm)
    CUQ 110 (110 x 110 mm)
    CUQ125 (125 x 125 mm)
    CUQ 160 (160 x 160 mm)
    CUQ 160 T (160 x 160 mm)
    CUQ 200 T (200 x 200 mm)
    CUQ 250 T (250 x 250 mm)
      
    90° Elbow M/F PN25
    CMF 20 (20 x 20 mm)
    CMF 25 (25 x 25 mm)
      
    Reduced 90° Elbow PN25
    CUR 2520 (25 x 20 mm)
    CUR 3220 (32 x 20 mm)
    CUR 3225 (32 x 25 mm)
      
    Reducing Bush M/F PN25
    RDZ 2520 (25 x 20 mm)
    RDZ 3220 (32 x 20 mm)
    RDZ 3225 (32 x 25 mm)
    RDZ 4020 (40 x 20 mm)
    RDZ 4025 (40 x 25 mm)
    RDZ 4032 (40 x 32 mm)
    RDZ 5020 (50 x 20 mm)
    RDZ 5025 (50 x 25 mm)
    RDZ 5032 (50 x 32 mm)
    RDZ 5040 (50 x 40 mm)
    RDZ 6320 (63 x 20 mm)
    RDZ 6325 (63 x 25 mm)
    RDZ 6332 (63 x 32 mm)
    RDZ 6340 (63 x 40 mm)
    RDZ 6350 (63 x 50 mm)
       
    Reducing Bush F/F PN25
    RDF 2520 (25 x 20 mm)
    RDF 3220 (32 x 20 mm)
    RDF 3225 (32 x 25 mm)
    RDF 4020 (40 x 20 mm)
    RDF 4025 (40 x 25 mm)
    RDF 4032 (40 x 32 mm)
    RDF 5020 (50 x 20 mm)
    RDF 5025 (50 x 25 mm)
    RDF 5032 (50 x 32 mm)
    RDF 5040 (50 x 40 mm)
    RDF 6320 (63 x 20 mm)
    RDF 6325 (63 x 25 mm)
    RDF 6332 (63 x 32 mm)
    RDF 6340 (63 x 40 mm)
    RDF 6350 (63 x 50 mm)
    RDF 7540 (75 x 40 mm)
    RDF 7550 (75 x 50 mm)
    RDF 7563 (75 x 63 mm)
    RDF 9050 (90 x 50 mm)
    RDF 9063 (90 x 63 mm)
    RDF 9075 (90 x 75 mm)
    RDF 11063 (110 x 63 mm)
    RDF 11075 (110 x 75 mm)
    RDF 11090 (110 x 90 mm)
    RDF 125110 (125 x 110 mm)
    RDF 160110 (160 x 110 mm)
    RDF 160125 (160 x 125 mm)
    RDT 200 160 (200 x 160 mm)
    RDT 250 200 (250 x 200 mm)
    RDT 250 160 (250 x 160 mm)
    
    Cap PN25
    TAC 20 (20 mm)
    TAC 25 (25 mm)
    TAC 32 (32 mm)
    TAC 40 (40 mm)
    TAC 50 (50 mm)
    TAC 63 (63 mm)
    TAC 75 (75 mm)
    TAC 90 (90 mm)
    TAC 110 (110 mm)
    TAC 125 (125 mm)
    TAC 160 T (160 mm)
    TAC 200 T (200 mm)
    TAC 250 T (250 mm)
       
    Tee PN25
    TEN 20 (20 x 20 x 20 mm)
    TEN 25 (25 x 25 x 25 mm)
    TEN 32 (32 x 32 x 32 mm)
    TEN 40 (40 x 40 x 40 mm)
    TEN 50 (50 x 50 x 50 mm)
    TEN 63 (63 x 63 x 63 mm)
    TEN 75 (75 x 75 x 75 mm)
    TEN 90 (90 x 90 x 90 mm)
    TEN 110 (110 x 110 x 110 mm)
    TEN 125 (125 x 125 x 125 mm)
    TEN 160 (160 x 160 x 160 mm)
    TEN 160 T (160 x 160 x 160 mm)
    TEN 200 T (200 x 200 x 200 mm)
    TEN 250 T (250 x 250 x 250 mm)
    
    Reducing Tee PN25
    TER 2520 (25 x 20 x 25 mm)
    TER 2521 (25 x 20 x 20 mm)
    TER 3220 (32 x 20 x 32 mm)
    TER 3225 (32 x 25 x 32 mm)
    TER 4020 (40 x 20 x 40 mm)
    TER 4025 (40 x 25 x 40 mm)
    TER 4032 (40 x 32 x 40 mm)
    TER 5020 (50 x 20 x 50 mm)
    TER 5025 (50 x 25 x 50 mm)
    TER 5032 (50 x 32 x 50 mm)
    TER 5040 (50 x 40 x 50 mm)
    TER 6320 (63 x 20 x 63 mm)
    TER 6325 (63 x 25 x 63 mm)
    TER 6332 (63 x 32 x 63 mm)
    TER 6340 (63 x 40 x 63 mm)
    TER 6350 (63 x 50 x 63 mm)
    TER 7540 (75 x 40 x 75 mm)
    TER 7550 (75 x 50 x 75 mm)
    TER 7563 (75 x 63 x 75 mm)
    TER 9050 (90 x 50 x 90 mm)
    TER 9063 (90 x 63 x 90 mm)
    TER 9075 (90 x 75 x 90 mm)
    TER 11063 (110 x 63 x 110 mm)
    TER 11075 (110 x 75 x 110 mm)
    TER 11090 (110 x 90 x 110 mm)
    TER 125110 (125 x 110 x 125 mm)
    TER 160110 (160 x 110 x 160 mm)
       
    Cross PN25
    TEQ 20 (20 x 20 x 20 x 20 mm)
        
    Union PN10
    UNI 2020 (20 x 20 mm)
    UNI 2525 (25 x 25 mm)
    UNI 3232 (32 x 32mm)
    UNI 4040 (40 x 40 mm)
    UNI 5050 (50 x 50 mm)
    UNI 6363 (63 x 63 mm)
[2] Stub End
    CTL 32 (32 mm)
    CTL 40 (40 mm)
    CTL 50 (50 mm)
    CTL 63 (63 mm)
    CTL 75 (75 mm)
    CTL 90 (90 mm)
    CTL 110 (110 mm)
    CTL 125 (125 mm)
    CTL 160 (160 mm)
    CTL 160 T (160 mm)
    CTL 200 T (200 mm)
    CTL 250 T (250 mm)
       
    Electrofusion Socket
    MAE 63 (63 x 63 mm)
    MAE 75 (75 x 75 mm)
    MAE 90 (90 x 90 mm)
    MAE 110 (110 x 110 mm)
    MAE 125 (125 x 125 mm)
    MAE 160 (160 x 160 mm)
    MAE 200 (200 x 200 mm)
    MAE 250 (250 x 250 mm)
[G] Product is Certified to NSF/ANSI/CAN 372 and conforms with the lead content requirements
    for "lead free" plumbing as defined by California, Vermont, Maryland, and Louisiana
    state laws and the U.S. Safe Drinking Water Act.

[3] Configurations include:
        
    Male Adapter Threaded Female PN25
    GFF 3220 (32 mm x 1/2")
        
    90° Threaded Elbow PN25 - Female
    CFF 2020 (20 mm x 1/2")
    CFF 2025 (20 mm x 3/4")
    CFF 2520 (25 mm x 1/2")
    CFF 2525 (25 mm x 3/4")
    CFF 3225 (32 mm x 3/4")
    CFF 3232 (32 mm x 1")
        
    90° Threaded Elbow PN25 - Male
    CFM 2020 (20 mm x 1/2")
    CFM 2025 (20 mm x 3/4")
    CFM 2520 (25 mm x 1/2")
    CFM 2525 (25 mm x 3/4")
    CFM 3225 (32 mm x 3/4")
    CFM 3232 (32 mm x 1")
        
    90° Long Threaded Elbow PN25 - Female
    CFL 2020 (20 mm x 1/2")
    CFL 2520 (25 mm x 1/2")
       
    90° Threaded Elbow with Bracket PN25 - Female
    FFS 2020 (20mm x 1/2")
    FFS 2520 (25 mm x 1/2")
    
    90° Threaded Elbow with Bracket PN25 - Male
    FMS 2020 (20 mm x 1/2")
    FMS 2520 (25 mm x 1/2")
       
    90° Threaded Elbow PN25 - Female with Male
    CCF 2020 (20 mm x 1/2")
       
    90° Threaded Elbow PN25 - Male with Male
    CCM 2020 (20 mm x 1/2")
        
    Threaded Tee PN25 - Female
    TEF 2020 (20 mm x 1/2" x 20 mm)
    TEF 2025 (20 mm x 3/4" x 20 mm)
    TEF 2520 (25 mm x 1/2" x 25 mm)
    TEF 2525 (25 mm x 3/4" x 25 mm)
    TEF 3225 (32 mm x 3/4" x 32 mm)
    TEF 3232 (32 mm x 1" x 32 mm)
       
    Threaded Tee PN25 - Male
    TEM 2020 (20 mm x 1/2" x 20 mm)
    TEM 2025 (20 mm x 3/4" x 20 mm)
    TEM 2520 (25 mm x 1/2" x 25 mm)
    TEM 2525 (25 mm x 3/4" x 25 mm)
    TEM 3225 (32 mm x 3/4" x 32 mm)
    TEM 3232 (32 mm x 1" x 32 mm)
    
    Threaded Coupling PN25 - Female
    RFF 2020 (20 mm x 1/2")
    RFF 2025 (20 mm x 3/4")
    RFF 2520 (25 mm x 1/2")
    RFF 2525 (25 mm x 3/4")
    RFF 3225 (32 mm x 3/4")
    RFF 3232 (32 mm x 1")
    RFF 4040 (40 mm x 1-1/4")
    RFF 5050 (50 mm x 1-1/2")
    RFF 6363 (63 mm x 2")
    RFF 7575 (75 mm x 2-1/2")
    RFF 9090 (90 mm x 3")
    RFF 110110 (110 mm x 4")
    
    Threaded Coupling PN25 - Male
    RFM 2020 (20 mm x 1/2")
    RFM 2025 (20 mm x 3/4")
    RFM 2520 (25 mm x 1/2")
    RFM 2525 (25 mm x 3/4")
    
    Fixed Wall Assembly Group
    GVF 2020 (20 mm x 1/2")
    GVF 2520 (25 mm x 1/2")
        
    Brass Adapter PN25 - Female
    GGF 2020 (20 mm x 1/2")
    GGF 2525 (25 mm x 3/4")
    GGF 3232 (32 mm x 1")
    GGF 4040 (40 mm x 1-1/4")
    GGF 5050 (50 mm x 1-1/2")
    GGF 6363 (63 mm x 2")
       
    Brass Adapter PN25 - Male
    GGM 2020 (20 mm x 1/2")
    GGM 2525 (25 mm x 3/4")
    GGM 3232 (32 mm x 1")
    GGM 4040 (40 mm x 1-1/")
    GGM 5050 (50 mm x 1-1/2")
    GGM 6363 (63 mm x 2")
    RFM 3225 (32 mm x 3/4")
    RFM 3232 (32 mm x 1")
    RFM 4040 (40 mm x 1-1/4")
    RFM 5050 (50 mm x 1-1/2")
    RFM 6363 (63 mm x 2")
    RFM 7575 (75 mm x 2-1/2")
    RFM 9090 (90 mm x 3")
    RFM 110110 (110 mm x 4")
       
    Wall Assembly Group
    GVS 2020 (1/2" x 1/2")
        
    Wall Assembly Group with Template
    GVD 2020 (20 mm x 1/2")
    GVD 2520 (25 mm x 1/2")
[G] Product is Certified to NSF/ANSI/CAN 372 and conforms with the lead content requirements
    for "lead free" plumbing as defined by California, Vermont, Maryland, and Louisiana
    state laws and the U.S. Safe Drinking Water Act.

[4] Pipe models include:
    
    FIBER Pipe
    TUB 20 SDR6 F
    TUB 25 SDR6 F
    
    FIBER EVO Pipe
    TUB 32 SDR9 FE
    TUB 40 SDR9 FE
    TUB 50 SDR9 FE
    TUB 63 SDR9 FE
    TUB 75 SDR9 FE
    TUB 90 SDR9 FE
    TUB 110 SDR9 FE
    TUB 125 SDR9 FE
    TUB 160 SDR9 FE
    TUB 200 SDR9 FE
    TUB 250 SDR9 FE
    TUB 20 SDR7.4 FE
    TUB 25 SDR7.4 FE
    TUB 32 SDR7.4 FE
    TUB 40 SDR7.4 FE
    TUB 50 SDR7.4 FE
    TUB 63 SDR7.4 FE
    TUB 75 SDR7.4 FE
    TUB 90 SDR7.4 FE
    TUB 110 SDR7.4 FE
    TUB 125 SDR7.4 FE
    TUB 160 SDR7.4 FE
    TUB 200 SDR7.4 FE
    TUB 250 SDR7.4 FE
    TUB 32 SDR11 FE
    TUB 40 SDR11 FE
    TUB 50 SDR11 FE
    TUB 63 SDR11 FE
    TUB 75 SDR11 FE
    TUB 90 SDR11 FE
    TUB 110 SDR11 FE
    TUB 125 SDR11 FE
    TUB 160 SDR11 FE
    TUB 200 SDR11 FE
    TUB 250 SDR11 FE
    TUB 160 SDR17 FE
    TUB 200 SDR17 FE
    TUB 250 SDR17 FE
      
    PPR Pipe
    TUB X A10 - PN10 - SDR11/S5 (20 – 63 mm)
    TUB X A16 - PN16 - SDR7.4/S3.2 (20 – 63 mm)
    TUB X A20 - PN20 - SDR6/S2.5 (20 – 63 mm)
      
    EvO Pipe
    TUB X A10 E - PN10 - SDR17/S8 (75 – 250 mm)
    TUB X A16 E - PN16 - SDR11/S5 (75 – 250 mm)
    TUB X A20 E - PN20 - SDR7.4/S3.2 (75 – 160 mm)
    TUB X A20 E - PN20 - SDR9/S4 (200 – 250 mm)
    TUB X A25 E - PN25 - SDR6/S2.5 (20 – 160 mm)
      
    X corresponds to the size in mm.
[G] Product is Certified to NSF/ANSI/CAN 372 and conforms with the lead content requirements
    for "lead free" plumbing as defined by California, Vermont, Maryland, and Louisiana
    state laws and the U.S. Safe Drinking Water Act.

[G] Product is Certified to NSF/ANSI/CAN 372 and conforms with the lead content requirements
    for "lead free" plumbing as defined by California, Vermont, Maryland, and Louisiana
    state laws and the U.S. Safe Drinking Water Act.

[1] This product is Certified for a maximum use level of 125 mg/L.
[G] Product is Certified to NSF/ANSI/CAN 372 and conforms with the lead content requirements
    for "lead free" plumbing as defined by California, Vermont, Maryland, and Louisiana
    state laws and the U.S. Safe Drinking Water Act.

[1] XX: DIN connector options	
    20 - 20 cable DIN	
    35 - 35 conduit DIN	
    40 - 40 cord DIN	
    	
    yyy:	
    038 - 3/8" NPT	
    012 - 1/2" NPT	
    034 - 3/4" NPT	
    100 - 1" NPT	
    125 - 1 1/4" NPT	
    150 - 1 1/2" NPT	
    200 - 2" NPT	
    	
    	
    zz:	
    11 - Dn11,5 G 3/8"	
    13 - Dn13,5 G 1/2"	
    13 - Dn13,5 G 3/4"	
    18 - Dn18 G 3/4"	
    26 - Dn26 G 1"	
    32 - Dn32 G 1 1/4"	
    45 - Dn45 G 1 1/2"	
    50 - Dn50 G 2"	
    	
    E: EPDM	
    	
    ww: Represents the series coil and may be any alphanumeric character
[G] Product is Certified to NSF/ANSI/CAN 372 and conforms with the lead content requirements
    for "lead free" plumbing as defined by California, Vermont, Maryland, and Louisiana
    state laws and the U.S. Safe Drinking Water Act.

[1] AA   - Body size (16, 18 ,22 ,24 ,28 ,2C, 2H, 4C, 4F, 4H, 4I, 4M, 4S, 4V, 6B, 6F, 6I, 
           8B, 8I, JI, JL, SI, SL, CI, CL, KI, LI, MI, NI, PI or QI)
    BBB  - Type of cartridge (168, 365, 605, ANA, ANB, ANZ, BFZ, FL1, FL2, FL3, FL4, FL5, 
           FL6, FL7, FL8, FL9, FLA, FLB, FLC, FLD, FLS, FLZ, FRO, FR2, FRE, HFA, HFB, HFC, 
           HFD, HFE, HFS, HPZ, HPA, HPB, HPC, HPL, HP1, HP2, HP3, HP4, HP5, HP6, HP7, HP8, 
           HP9, H12, M15, NR0, O15, ON1, ON2, ON3, ON4, ON5, ON6, ON7, ON8, ON9, O12, ONA, 
           ONB, ONC, OND, ONE, ONF, ONL, ONS, ONZ, OW2, OWA, OWB, OWC, OWD, OWL, OWS, 
           SRB, SRC, SRO, or SIN)
    CC   - Type of gasket (00, 05, 06, 10, 11, 15, 16, 20, 21, 25, 30, 35, 40, 55, 60,
           61, 65, 66, 70, 71, 75, 76, 80 , 81 or 85)
    DDD  - Color (any three alpha numeric characters)
    EEEE - Personalization (any four alpha numeric characters)
    VMS International (VPAK) H20Miser Model 16001 is a kit with three replacement aerators.

[Q] This product meets the reduced Q test statistic criteria of 1 µg or 0.5 µg for lead per
    Section 9.5.1.1 of NSF/ANSI/CAN 61.

[2] MICRO Designations: 
    AAAA - Color (any alpha numeric characters) 
    BB   - Micro Style wand (GD, GJ, GS, MD, MJ, MS, MA, MP, MF, MR, PD, PJ, PS, and DO) 
    CC   - Shell design (any alpha numeric characters) 
    DD   - Waterway (BA, BB, BC, BD, BE, BF, B1, B2, B3, B4, B5, B6, B7, B8, B9, BX, C1, 
           C2, C3, C4, C5, C6, C7, C8, C9, D1, D2, D3, D4, G1, G2, G3, G4, G5, G6, L1, 
           L2, L3, L4, L5, L6, and T5) or Waterway Extension (M3, M4, M5, M6, M7, P1, 
           P2 - only used with L1 - L6 waterways). 
    E    - Distributor (1, 2, 3, 4, 5, and 6) 
    F    - Spring (0, 1, 2, 3, 4, 5, 6, 7, 8, or 9) 
    GG   - Aerator (F1, F2, F3, F4, F5, F6, F7, F8, F9, J1, J2, J3, J4, J5, J6, J7, J8, 
           J9, K1, N1, N5, N6, N7, N8, N9, S1, S2, S3, V1, V5, V6, V7, V8, V9, A1, A2, 
           A3, A4, or A5) 
    HH   - Flow controller (00, 01, 02, 03, 04, 05, 10, 14, 15, 16, 17, 18, 19, or 20) 
    I    - Trigger (any single alpha or numeric characters) 
    J    - Faceplates (0, 1, 2, 3, 4, 5, 6, 7, 8, 9 A, B, C, D, E, and F) 
    K    - Packaging (any single alpha or numeric characters) 
    L    - Customization (any single alpha or numeric characters)
[3] Only products bearing the NSF Mark on the product, product packaging, and/or
    documentation shipped with the product are Certified.
[4] MICRO EVO Designations: 
    AAAA - Color (any alpha numeric characters) 
    BB   - Micro Evo Style wand (ED, EJ or ES) 
    CC   - Shell design (any alpha numeric characters) 
    D    - Threaded Distributor (1, 2, 3, 4, 5, or 6) 
    EE   - Waterway Extension (R1, R2, R3, R4, A1, A2, A3, A4, B1, B2, B3, or B4) 
    F    - Waterway (0, 1, 2, 3, or 4) 
    G    - Spring (0, 1, 2, 3, or 4) 
    HH   - Aerator (D1, D5, D6, D7, D8, D9, S2, J1, J2, J3, J4, J5, J6, J7, J8, or J9) 
    I    - Flow controller (0, 1, 2, 3, 4, 5) 
    J    - Trigger (any single alpha or numeric characters) 
    K    - Faceplate (0, 1, 2, 3, or 4)
    L    - Packaging (any single alpha or numeric characters) 
    M    - Customization (any single alpha or numeric characters)
[5] Professional Slim 115 DJ 10x1 MGTC LONG - B020P5CCP916N900P120
    
    Professional Slim 115 Spray 10x1 MGTC LONG - B020P6CCP916S100P120
    
    Explanation of naming: 
    AAAABBCCDDEFGGHHIJKL
    
    AAAA: Color (any alpha numeric characters) 
    
    BB:
    P5 - “PROFESSIONAL SLIM 115 DUAL JET”
    P6 - “PROFESSIONAL SLIM 115 SPRAY”
    
    CC: Shell design (any alpha numeric characters) 
    
    DD: 
    P9 - Different design of waterway (Part 1) made in “BRASS OT57-USA”
    
    E: 
    1 - The distributor for Micro Dual-Jet, Micro Spray, Micro Mango Dual-Jet and Micro
    Mango Spray, Professional Dual-Jet and Professional Spray 
    F: 
    6 - Nine different designs of springs. 
    
    GG: 
    N9 - Different aerators for Micro Dual-Jet with faceplate 1 or 2 
    S1 - Different design of aerator cap (part 10.7) 
    
    HH: 
    00 - Without Flow Controller
    
    I: Trigger (any single alpha or numeric characters) 
    
    J: 
    1 - Different designs of Faceplates. 
    
    K: Packaging (any single alpha or numeric characters) 
    
    L: Customization (any single alpha or numeric characters)
[6] Professional Slim 115 DJ 10x1 MGTC SHORT - B020P5CCPA16N900P120
    
    Professional Slim 115 Spray 10x1 MGTC SHORT - B020P6CCPA16S100P120
    
    Explanation of naming: 
    AAAABBCCDDEFGGHHIJKL
    
    AAAA: Color (any alpha numeric characters) 
    
    BB:
    P5 - “PROFESSIONAL SLIM 115 DUAL JET”
    P6 - “PROFESSIONAL SLIM 115 SPRAY”
    
    CC: Shell design (any alpha numeric characters) 
    
    DD: 
    PA - Different design of waterway (Part 1) made in “BRASS OT57-USA”
    
    E: 
    1 - The distributor for Micro Dual-Jet, Micro Spray, Micro Mango Dual-Jet and Micro
    Mango Spray, Professional Dual-Jet and Professional Spray 
    F: 
    6 - Nine different designs of springs. 
    
    GG: 
    N9 - Different aerators for Micro Dual-Jet with faceplate 1 or 2 
    S1 - Different design of aerator cap (part 10.7) 
    
    HH: 
    00 - Without Flow Controller
    
    I: Trigger (any single alpha or numeric characters) 
    
    J: 
    1 - Different designs of Faceplates. 
    
    K: Packaging (any single alpha or numeric characters) 
    
    L: Customization (any single alpha or numeric characters)
[7] Professional Slim 115 DJ 3/8'' - B020P5CCP716N900P120
    
    Professional Slim 115 Spray 3/8'' - B020P6CCP716S100P120
    
    Explanation of naming: 
    AAAABBCCDDEFGGHHIJKL
    
    AAAA: Color (any alpha numeric characters) 
    
    BB:
    P5 - “PROFESSIONAL SLIM 115 DUAL JET”
    P6 - “PROFESSIONAL SLIM 115 SPRAY”
    
    CC: Shell design (any alpha numeric characters) 
    
    DD: 
    P7 - Different design of waterway (Part 1) made in “BRASS OT57-USA”
    
    E: 
    1 - The distributor for Micro Dual-Jet, Micro Spray, Micro Mango Dual-Jet and Micro
    Mango Spray, Professional Dual-Jet and Professional Spray 
    F: 
    6 - Nine different designs of springs. 
    
    GG: 
    N9 - Different aerators for Micro Dual-Jet with faceplate 1 or 2 
    S1 - Different design of aerator cap (part 10.7) 
    
    HH: 
    00 - Without Flow Controller
    
    I: Trigger (any single alpha or numeric characters) 
    
    J: 
    1 - Different designs of Faceplates. 
    
    K: Packaging (any single alpha or numeric characters) 
    
    L: Customization (any single alpha or numeric characters)
[8] Professional Slim 115 DJ 1/2” - B020P5CCP816N900P120
    
    Professional Slim 115 Spray 1/2” - B020P6CCP816S100P120
    
    Explanation of naming: 
    AAAABBCCDDEFGGHHIJKL
    
    AAAA: Color (any alpha numeric characters) 
    
    BB:
    P5 - “PROFESSIONAL SLIM 115 DUAL JET”
    P6 - “PROFESSIONAL SLIM 115 SPRAY”
    
    CC: Shell design (any alpha numeric characters) 
    
    DD: 
    P8 - Different design of waterway (Part 1) made in “BRASS OT57-USA”
    
    E: 
    1 - The distributor for Micro Dual-Jet, Micro Spray, Micro Mango Dual-Jet and Micro
    Mango Spray, Professional Dual-Jet and Professional Spray 
    F: 
    6 - Nine different designs of springs. 
    
    GG: 
    N9 - Different aerators for Micro Dual-Jet with faceplate 1 or 2 
    S1 - Different design of aerator cap (part 10.7) 
    
    HH: 
    00 - Without Flow Controller
    
    I: Trigger (any single alpha or numeric characters) 
    
    J: 
    1 - Different designs of Faceplates. 
    
    K: Packaging (any single alpha or numeric characters) 
    
    L: Customization (any single alpha or numeric characters)
[9] Professional Slim 93 Spray 10x1 MGTC LONG - B020P2CCP556S100Q120
    
    Professional Slim 93 DJ 10x1 MGTC LONG - B020P1CCP556N900Q120
    
    Professional Slim Comfort 93 DJ 10x1 MGTC - B020P3CCP556N900I12W
    
    Professional Slim Comfort 93 Spray 10x1 MGTC - B020P4CCP556S100I12W
    
    Explanation of naming: 
    AAAABBCCDDEFGGHHIJKL
    
    AAAA: Color (any alpha numeric characters) 
    
    BB:
    P1 - CPROFESSIONAL SLIM 93 DUAL JET”
    P2 - “PROFESSIONAL SLIM 93 SPRAY”
    P3 - “PROFESSIONAL SLIM 93 COMFORT DUAL JET”
    P4 - “PROFESSIONAL SLIM 93 COMFORT SPRAY”
    
    
    CC: Shell design (any alpha numeric characters) 
    
    DD: 
    P5 - Different design of waterway (Part 1) made in “BRASS OT57-USA”
    
    E: 
    5 - Different design of distributor external dimensions (Part # 9.4) for Media, Media
    Plus, Media Brass, Media Brass Plus. 
    
    F: 
    6 - Nine different designs of springs. 
    
    GG: 
    N9 - Different aerators for Micro Dual-Jet with faceplate 1 or 2 
    S1 - Different design of aerator cap (part 10.7) 
    
    HH: 
    00 - Without Flow Controller
    
    I: Trigger (any single alpha or numeric characters) 
    
    J: 
    1 - Different designs of Faceplates. 
    
    K: Packaging (any single alpha or numeric characters) 
    
    L: Customization (any single alpha or numeric characters)
[G] Product is Certified to NSF/ANSI/CAN 372 and conforms with the lead content requirements
    for "lead free" plumbing as defined by California, Vermont, Maryland, and Louisiana
    state laws and the U.S. Safe Drinking Water Act.
[10] Professional Slim 93 Spray 3/8” - B020P2CCP356S100Q120
     
     Professional Slim 93 DJ 3/8” - B020P1CCP356N900Q120
     
     Explanation of naming: 
     AAAABBCCDDEFGGHHIJKL
     
     AAAA: Color (any alpha numeric characters) 
     
     BB:
     P1 - “PROFESSIONAL SLIM 93 DUAL JET”
     P2 - “PROFESSIONAL SLIM 93 SPRAY”
     
     CC: Shell design (any alpha numeric characters) 
     
     DD: 
     P3 - different design of waterway (Part 1) made in “BRASS OT57-USA”
     
     E: 
     5 - Different design of distributor external dimensions (Part # 9.4) for Media, Media
     Plus, Media Brass, Media Brass Plus. 
     
     F: 
     6 - Nine different designs of springs. 
     
     GG: 
     N9 - Different aerators for Micro Dual-Jet with faceplate 1 or 2 
     S1 - Different design of aerator cap (part 10.7) 
     
     HH: 
     00 - Without Flow Controller
     
     I: Trigger (any single alpha or numeric characters) 
     
     J: 
     1 - Different designs of Faceplates. 
     
     K: Packaging (any single alpha or numeric characters) 
     
     L: Customization (any single alpha or numeric characters)
[11] Professional Slim 93 Spray 1/2” - B020P2CCP456S100Q120
     
     Professional Slim 93 DJ 1/2” - B020P1CCP456N900Q120
     
     Explanation of naming: 
     AAAABBCCDDEFGGHHIJKL
     
     AAAA: Color (any alpha numeric characters) 
     
     BB:
     P1 - “PROFESSIONAL SLIM 93 DUAL JET”
     P2 - “PROFESSIONAL SLIM 93 SPRAY”
     
     CC: Shell design (any alpha numeric characters) 
     
     DD: 
     P4 - Different design of waterway (Part 1) made in “BRASS OT57-USA”
     
     E: 
     5 - Different design of distributor external dimensions (Part # 9.4) for Media, Media
     Plus, Media Brass, Media Brass Plus. 
     
     F: 
     6 - Nine different designs of springs. 
     
     GG: 
     N9 - Different aerators for Micro Dual-Jet with faceplate 1 or 2 
     S1 - Different design of aerator cap (part 10.7) 
     
     HH: 
     00 - Without Flow Controller
     
     I: Trigger (any single alpha or numeric characters) 
     
     J: 
     1 - Different designs of Faceplates. 
     
     K: Packaging (any single alpha or numeric characters) 
     
     L: Customization (any single alpha or numeric characters)
[12] Professional Slim 93 Spray 10x1 MGTC SHORT - B020P2CCP656S100Q120
     
     Professional Slim 93 DJ 10x1 MGTC SHORT - B020P1CCP656N900Q120
     
     Explanation of naming: 
     AAAABBCCDDEFGGHHIJKL
     
     AAAA: Color (any alpha numeric characters) 
     
     BB:
     P1- “PROFESSIONAL SLIM 93 DUAL JET”
     P2- “PROFESSIONAL SLIM 93 SPRAY”
     
     CC: Shell design (any alpha numeric characters) 
     
     DD: 
     P6 - different design of waterway (Part 1) made in “BRASS OT57-USA”
     
     E: 
     5 - Different design of distributor external dimensions (Part # 9.4) for Media, Media
     Plus, Media Brass, Media Brass Plus. 
     
     F: 
     6 - Nine different designs of springs. 
     
     GG: 
     N9 - Different aerators for Micro Dual-Jet with faceplate 1 or 2 
     S1 - Different design of aerator cap (part 10.7) 
     
     HH: 
     00 - Without Flow Controller
     
     I: Trigger (any single alpha or numeric characters) 
     
     J: 
     1 - Different designs of Faceplates. 
     
     K: Packaging (any single alpha or numeric characters) 
     
     L: Customization (any single alpha or numeric characters)

[Q] This product meets the reduced Q test statistic criteria of 1 µg or 0.5 µg for lead per
    Section 9.5.1.1 of NSF/ANSI/CAN 61.

[Q] This product meets the reduced Q test statistic criteria of 1 µg or 0.5 µg for lead per
    Section 9.5.1.1 of NSF/ANSI/CAN 61.

[Q] This product meets the reduced Q test statistic criteria of 1 µg or 0.5 µg for lead per
    Section 9.5.1.1 of NSF/ANSI/CAN 61.
[13] R   - Regulator 
     (1) - Type of Regulator: A, B, C, D, or E 
     (3) - Flow Rate: 3, 4, 5, 6, 7, 8, 9, 10, 11, 12, 13, 14, or 15
     (4) - Regulator Color: Black, blue, brown, green, grey, light grey, red, white, 
           yellow, orange, fuscia or pink

[G] Product is Certified to NSF/ANSI/CAN 372 and conforms with the lead content requirements
    for "lead free" plumbing as defined by California, Vermont, Maryland, and Louisiana
    state laws and the U.S. Safe Drinking Water Act.
[Q] This product meets the reduced Q test statistic criteria of 1 µg or 0.5 µg for lead per
    Section 9.5.1.1 of NSF/ANSI/CAN 61.
[14] Side Spray Diverter Valve Assembly
     ABCDEFGH
     A - Valve stem (1)
     B - Sealing washer (2)
     C - Valve shell (3)
     D - Shell O-ring (4)
     E - Conical washer (5)
     F - Side spray washer (6)
     G - Side spray housing (0,7,1)
     H - Side spray shell (0,8)

[G] Product is Certified to NSF/ANSI/CAN 372 and conforms with the lead content requirements
    for "lead free" plumbing as defined by California, Vermont, Maryland, and Louisiana
    state laws and the U.S. Safe Drinking Water Act.
[Q] This product meets the reduced Q test statistic criteria of 1 µg or 0.5 µg for lead per
    Section 9.5.1.1 of NSF/ANSI/CAN 61.

[15] AAAA - Color (any four digit number)
       BB - Concept style wand (CG, CT, CY, EP, GP, OP, QP, TP, TX, or YP)
       CC - Waterway (G1, G2, T1, or T2)
       DD - Diverter shell (01, 02, 03)
        E - Eccentric plug (1, 2, 3, or 4)
        F - Spring (0, 1, or 2)
        G - Aerator (0, 1, 2, 5, A, C, E, F, G, H, J, K, L, M, S, T, U, V, W, X, Y, Z, 
            &, or £)
        H - Flow controller (0, 1, 2, 3, 4, 5, 6, 9, A, or B)
        I - Trigger cover (any single alpha or numeric character)
        J - Trigger cover insert (any single alpha or numeric character)
       KK - Faceplate style (D1, D2, D3, D4, D5, or D6)
        L - Packaging (any single digit number)
        M - Screen washer type (0, 1, 2, or M)

[16] AAAA - Color (any four digit number)
        B - Macro Corta style wand (MC)
        C - Waterway (A, H, K, L, M, N, or P)
        D - Circular insert (4 or 5)
        E - Spring (0, 2, 3 or 4)
        F - Aerator (0, 1, 2, 5, A, E, F, G, H, I, J, K, L, M, P,Q, U, V, W, Y, Z, &, or £)
        G - Flow controller (0, 1, 2, 3, 4, 5, 6, 7, 8, 9, A, B, or C)
        H - Button/trigger cover (any single alpha or numeric character)
       II - Faceplate style (16, 51, A1, A2, A4, A6, A7, B1, B2,B3, B4, P1, P3, or P5)
        J - Packaging (any single digit number)
        K - Screen washer type (0, 1, or 2)
        L - Unassigned (any single digit number)
       MM - Trigger cover insert (any two alpha or numeric characters)
        N - Custom version (any single digit number)

[17] AAAA - Color (any four digit number)
       BB - Macro Ergo style wand (ME)
        C - Waterway (5, 6, 8, 9, C, D, E, G, H, K, L, M, N, P, R, T, U, or V)
        D - Circular insert (4 or 5)
        E - Spring (0, 2, 3 or 4)
        F - Aerator (0, 1, 2, 5, A , E, F, G, H, I, J, K, L, M, P, Q, U, V, W, Y, Z, &, 
            or £)
        G - Flow controller (0, 1, 2, 3, 4 , 5 , 6, 7, 8, 9, A,B, or C)
        H - Button/trigger cover (any single alpha or numeric character)
       II - Faceplate style (16, 51, A1, A2, A4, A6, A7, B1, B2,B3, B4, P1, P2, P3, or P5)
        J - Package (any single digit number)
        K - Screen washer type (0, 1, or 2)
        L - Grip (any single digit number)
       MM - Trigger cover insert (any two alpha or numeric characters)
        N - Custom version (any single digit number)

[18] AAAA - Color (any four digit number)
       BB - Macro Long style wand (ML)
        C - Waterway (5, 6, 8, 9, C, D, E, G, H, K, L, M, N, P, R, T, U,or V)
        D - Circular insert (4 or 5)
        E - Spring (0, 2, 3 or 4)
        F - Aerator (0, 1, 2, 5, A, E, F, G, H, I, J, K, L, M, P,Q, U, V, W, Y, Z, &, or £)
        G - Flow controller (0, 1, 2, 3, 4, 5, 6, 7, 8, 9, A, B, or C)
        H - Button/trigger cover (any single alpha or numeric character)
       II - Faceplate style (16, 51, A1, A2, A4, A6, A7, B1, B2,B3, B4, P1, P3, or P5)
        J - Packaging (any single digit number)
        K - Screen washer type (0, 1, or 2)
        L - Unassigned (any single digit number)
       MM - Trigger cover insert (any two alpha or numeric characters)
        N - Custom version (any single digit number)

[19] AAAA - Color (any four digit number)
       BB - Signum style wand (BK, MB, MN, MX, SB, SL, SR, or ST)
       CC - Waterway 1 (A1, A2, A3, A4, B1, B2, B3, F1, F3, G1,G2, M1, or M2)
        D - Waterway 1.1 (0, 1, 2, 3, or 4)
        E - Cap (1 or 2)
        F - Circular insert (1, 2, 3, or 4)
        G - Spring (0, 1, 2, 4 or 6)
        H - Aerator (0, 1, 2, 3, 4, 5, 6, 7, 8, 9, A, B, C, E, J, T or Q)
        I - Diverter stem assembly (1, 2, 3, or 4)
        J - Flow controller (0, 1, 2, 3, 4, 5, 6, 7, 8, 9, A, B,C, E, or F)
        K - Button/trigger cover (any single alpha or numeric character)
       LL - Faceplate style (A1, A2, A3, B1, B2, B3, C1, C2, C3, D0, D1, D2, D3, D4, 
            D5, D6, D7, D8, D9, E1, E2 E3, or E4)
        M - Packaging (any single digit number)
        N - Screen washer type (0, 1, 2, or M)

[20] AAAA - Color (any four digit number)
        B - Grafic style wand (G)
        C - Waterway (1, 2, 3, 4, 5, 6, 7, A, B, C, G, H, L, M, N, or P)
        D - Circular insert (1 or 2)
        E - Spring (0, 2, 3 or 4)
        F - Aerator (0, 1, 2, 5, A, E, F, G, H, I, J, K, L, M, P, Q, U, V, W, Y, Z, &, 
            or £)
        G - Flow controller (0, 1, 2, 3, 4, 5, 6, 7, 8, 9, A, B, or C)
        H - Button/trigger cover (any single alpha or numeric character)
       II - Faceplate style (01, 03, 12, 13, 14, 15, 16, 17, 18,or 23)
        J - Packaging (any single digit number)
        K - Screen washer type (0,1, or 2)

[21] AAAA - Color (any alpha numeric characters)
       BB - Idea Style wand (IB, IC, ID, IG, IL, IO, IY, or IZ)
        C - Waterway (0, 1, 2, 3, 4, 5, 6, 7, 8 or 9)
        D - Distributor (1, 2, 3, 4, 5, 6, 7, 8, or 9)
        E - Spring (0, 1, 2, or 3)
        F - Aerator (0, 1, 2, 5, A, E, F, G, H, I, J, K, L, M, N, P, Q, U, V, W, Y, Z, 
            &, or £)
        G - Flow controller (0, 1, 2, 3, 4, 5, 6, 7, 8, 9, A, C, or D)
        H - Button/trigger cover (any single alpha or numeric character)
       II - Faceplate style (16, 51, A1, A2, A4, A6, A7, B1, B2,B3, B4, P1,P2, P3, or P5)
        J - Packaging (any single digit number)
        K - Screen washer type (0, 1, 2, or A)

[22] AAAA - Color (any four digit number)
       BB - Liberty style wand (LB)
        C - Waterway (5, 6, 7, 8, 9, C, E, G, H, K, L, M, N, P, R, T, U, or V)
        D - Circular insert (4 or 5)
        E - Spring (0, 2, 3 or 4)
        F - Aerator (0, 1, 2, 5, A, E, F, G, H, I, J, K, L, M, P, Q, U, V, W, Y, Z, 
            &, or £)
        G - Flow controller (0, 1, 2, 3, 4, 5, 6, 7, 8, 9, A, B, or C)
        H - Button/trigger cover (any single alpha or numeric character)
       II - Faceplate style (16, 51, A1, A2, A3, A4, A6, A7, B1,B2, B3, B4, P1, P2, P3, 
             or P5)
        J - Packaging (any single digit number)
        K - Screen washer type (0, 1, or 2)
        L - Handle ring trim (any single alpha or numeric character)
       MM - Handle (any two alpha or numeric characters)
        N - Head ring trim (any single alpha or numeric character)

[23] AAAA - Color (any four digit number)
        B - Studio style wand (S, Z, or K)
        C - Waterway (1, 2, 3, 4, 5, 6, 7, 8, 9, B, C, E, G, H, K, L, M, N, P, R, 
            T, V, or W)
        D - Circular insert (4 or 5)
        E - Spring (0, 1, 2, 3, or 4)
        F - Aerator (0, 1, 2, 5, A, E, F, G, H, I, J, K, L, M, P, Q, U, V, W, Y, Z, 
            &, or £)
        G - Flow controller (0, 1, 2, 3, 4, 5, 6, 7, 8, 9, A, B, or C)
        H - Button/trigger cover (any single alpha or numeric character)
       II - Faceplate style (16, 51, A1, A2, A4, A6, A7, B1, B2,B3, B4, P1, P2, P3, or P5)
        J - Packaging (any single digit number)
        K - Screen washer type (0, 1, or 2)

[24] AAAA - color (any four digit number)
       BB - Victoria style wand (VI or VA)
        C - Waterway (5, 6, 8, 9, C, E, G, H, K, L, M, N, P, R, T, U, or V)
        D - Circular insert (4 or 5)
        E - Spring (0, 2, 3, or 4)
        F - Aerator (0, 1, 2, 5, A, E, F, G, H, I, J, K, L, M, P, Q, U, V, W, Y, Z, 
            &, or £)
        G - Flow controller (0, 1, 2, 3, 4, 5 , 6, 7, 8, 9, A, B, or C)
        H - Button/trigger cover (any single alpha or numeric character)
       II - Faceplate style (16, 51, A1, A2, A4, A6, A7, B1, B2,B3, B4, P1, P3, or P5)
        J - Packaging (any single digit number)
        K - Screen washer type (0, 1, or 2)
        L - Grip (any single alpha or numeric character)
       MM - (any two alpha or numeric characters)
        N - Custom version (any single alpha or numeric character)

[G] Product is Certified to NSF/ANSI/CAN 372 and conforms with the lead content requirements
    for "lead free" plumbing as defined by California, Vermont, Maryland, and Louisiana
    state laws and the U.S. Safe Drinking Water Act.
[Q] This product meets the reduced Q test statistic criteria of 1 µg or 0.5 µg for lead per
    Section 9.5.1.1 of NSF/ANSI/CAN 61.

[1] Certified for a maximum surface area to volume ratio of 2.0 sq. in./L.

[2] Certified for a maximum surface area to volume ratio of 2.0 sq. in./L.

[1] This product does not require a Q statistic. It is made from material or materials that
    do not require lead analysis when reviewed per NSF/ANSI/CAN Standard 61, Section 3.3.

[1] This product has also been evaluated for use in Mechanical Plumbing Device applications
    with a maximum use restriction of 2.0 square inches/L.
[2] Certified for a maximum surface area to volume ratio of 2.0 sq. in./L.
[3] This product has also been evaluated for use in Mechanical Plumbing Device applications
    with a maximum use restriction of 0.2 sq. in./L.

[1] This product is also evaluated for use in Mechanical Plumbing Device applications with a
    maximum use restriction of 10.0 sq. in./L.
[2] Certified for a maximum surface area to volume of 10 sq. in./L.

[1] Certified for a maximum surface area to volume ratio of 2.0 square inches/L.

[1] Certified for a maximum surface area to volume ratio of 2.0 square inches/L.

[1] Certified for a maximum surface area to volume ratio of 2.0 sq. in./L
[2] Only products bearing the NSF Mark on the product, product packaging, and/or
    documentation shipped with the product are Certified.

[1] The 4040 models are flushed for 24 hours at a rate of 17 liters per minute with DI
    water.
    The 4040 models are Certified for a minimum daily flow of 2,271 liters per day.
[2] The 8040 models are flushed for 24 hours at a rate of 200 liters per minute with DI
    water.
    The 8040 models are Certified for a minimum daily flow of 12,617 liters per day.
[G] Product is Certified to NSF/ANSI/CAN 372 and conforms with the lead content requirements
    for "lead free" plumbing as defined by California, Vermont, Maryland, and Louisiana
    state laws and the U.S. Safe Drinking Water Act.

[1] This product has also been evaluated for use in Mechanical Plumbing Device applications
    with a maximum use restriction of 2.0 sq. in./L.
[2] Certified for a maximum surface area to volume ratio of 2.0 sq. in./L.
[3] This product has also been evaluated for use in Mechanical Plumbing Device applications
    with a maximum use restriction of 9 sq. in./L.
[4] Product may be coated with Art-Coat Treatment
[5] Certified for a maximum surface area to volume ratio of 30.0 sq. in./L.
[6] Certified for a maximum surface area to volume ratio of 14 sq. in./L. 

[1] This product has also been evaluated for use in Mechanical Plumbing Device applications
    with a maximum use restriction of 2.0 sq. in./L.
[2] Certified for a maximum surface area to volume ratio of 2.0 sq. in./L.
[3] This product has also been evaluated for use in Mechanical Plumbing Device applications
    with a maximum use restriction of 9 sq. in./L.
[4] Product may be coated with Art-Coat Treatment
[5] Certified for a maximum surface area to volume ratio of 30.0 sq. in./L.
[6] Certified for a maximum surface area to volume ratio of 14 sq. in./L. 

[2] Certified for a maximum surface area to volume ratio of 9.5 sq. in./L.
[3] Certified for a maximum surface area to volume ratio of 30.0 sq. in./L.
[4] Product may be coated with Art-Coat Treatment

[1] This product does not require a Q statistic. It is made from material or materials that
    do not require lead analysis when reviewed per NSF/ANSI/CAN Standard 61, Section 3.3.

[2] Certified for a maximum surface area to volume ratio of 9.5 sq. in./L.
[3] Certified for a maximum surface area to volume ratio of 30.0 sq. in./L.
[4] Product may be coated with Art-Coat Treatment

[1] This product does not require a Q statistic. It is made from material or materials that
    do not require lead analysis when reviewed per NSF/ANSI/CAN Standard 61, Section 3.3.

[1] Certified for use in well casings with a diameter of 6" and greater and at least 40 feet
    in depth.
[2] Certified for cables with a maximum length of 13 feet.
[3] Certified for a minimum flow of 3,000 gallons per day.
[G] Product is Certified to NSF/ANSI/CAN 372 and conforms with the lead content requirements
    for "lead free" plumbing as defined by California, Vermont, Maryland, and Louisiana
    state laws and the U.S. Safe Drinking Water Act.

[G] Product is Certified to NSF/ANSI/CAN 372 and conforms with the lead content requirements
    for "lead free" plumbing as defined by California, Vermont, Maryland, and Louisiana
    state laws and the U.S. Safe Drinking Water Act.

[1] Certified for a maximum surface area to volume ratio of 2.0 sq. in./L.

[1] Certified for a maximum surface area to volume ratio of 2.0 sq. in./L.

[1] Certified for a maximum surface area to volume ratio of 3.0 square inches/L.
[2] This product has also been evaluated for use in Mechanical Plumbing Device applications
    with a maximum use restriction of 3.0 square inches/L.

[Q] This product meets the reduced Q test statistic criteria of 1 µg or 0.5 µg for lead per
    Section 9.5.1.1 of NSF/ANSI/CAN 61.

[1] This certification includes NSF-61 Section 9 for Cold/Ambient temperature water
    pathways. The sparkling water pathway is not evaluated to NSF-61.
[2] The maximum operating temperature of these units is 74 F/23°C.
[G] Product is Certified to NSF/ANSI/CAN 372 and conforms with the lead content requirements
    for "lead free" plumbing as defined by California, Vermont, Maryland, and Louisiana
    state laws and the U.S. Safe Drinking Water Act.

[1] (u) - Lining material
          PP - Polypropylene
          PT - PTFE
          EN - Ebonite
    (v) - Diameter nominal (DN)
          25  - 1"
          32  - 1 1/4"
          40  - 1 1/2"
          50  - 2"
          65  - 2 1/2"
          80  - 3"
          100 - 4"
          125 - 5"
          150 - 6"
          200 - 8"
          250 - 10"
          300 - 12"
          350 - 14"
          400 - 16"
    (w) - Gasket material
         00 - No O-Ring (for PTFE & Ebonite lining only)
         FF - FKM O-Ring (for PP lining only)
    (x) - Body material (ST,VH,VC)
    (y-y) Number and electrode material
    2-VH : 2 measure electrodes in AISI 316
    3-VH : 2 measure + 1 ground electrodes in AISI 316
    (z) - Execution and Protection Rate 
          1 - Remote 
          3 - Compact
    (x) and (z) are non-wetted components.
    16,40 is the pressure rate: no influence on the wetted components
    JW.. is the lenght of the cable: no influence on the wetted components
[2] (t) - Lining material
          PP - Polypropylene
          PT - PTFE
          EN - Ebonite
    (u) - Diameter Nominal (DN)
          25  - 1"
          32  - 1 1/4"
          40  - 1 1/2"
          50  - 2"
          65  - 2 1/2"
          80  - 3"
          100 - 4"
          125 - 5"
          150 - 6"
          200 - 8"
          250 - 10"
          300 - 12"
          350 - 14"
          400 - 16"
          450 - 18"
          500 - 20"
          550 - 22"
          600 - 24"
          650 - 26"
          700 - 28" 
          750 - 30"
          800 - 32"
          850 - 34"
          900 - 26"
          1000 - 40"
          1200 - 48"
          1400 - 56" 
          1600 - 62"
          1800 - 70"
          2000 - 78"
    (v) - Gasket material
          00 - No O-Ring (for PTFE & Ebonite lining only)
          FF - FKM O-Ring (for PP lining only)
    (w) - Flange type (FA-FD-FJ)
    (x) - Body material (ST,VH,VC)
    (y-y) Number and electrode material
    2-VH : 2 measure electrodes in AISI 316
    3-VH : 2 measure + 1 ground electrodes in AISI 316
    (z) - Execution and Protection Rate 
          1 - Remote 
          3 - Compact
    10, 16, 25, 40, 64 is the pressure rate: no influence on the wetted components
    JW.. is the lenght of the cable: no influence on the wetted components

[1] Sizes indicated are expressed as diameter x length.
[2] Certified for a minimum permeate (product water) flow of 1,191 L/day.
[3] Certified elements must be flushed of preservative in the field for a minimum of 2 hours
    at the following parameters:
    PERMAQ5-4014, 1000 l/h at 225 psi
    PERMAQ5-4021, 1000 l/h at 225 psi
    PERMAQ5-4641, 1500 l/h at 225 psi
    PERMAQ6-4040, 1000 l/h at 225 psi
    PERMAQ1-4018 HF, 1000 l/h at 150psi
    PERMAQ1-4018 S , 1000 l/h at 150 psi
    PERMAQ1-4018 S HF, 1000 l/h at 150 psi
    PERMAQ1-4021 S, 1000 l/h at 150 psi
    PERMAQ1-4021 S HF, 1000 l/h at 150 psi
    PERMAQ1-4040, 1000 l/h at 150 psi
    PERMAQ1-4611, 1000 l/h at 150 psi
    PERMAQ1-8040, 1500 l/h at 150 psi
    PERMAQ1-8040 W, 1500 l/h at 150 psi
    PERMAQ2R-4040 W, 1500 l/h at 150 psi
    PERMAQ2-4018 S, 1000 l/h at 150 psi
    PERMAQ2-4018 HF, 1000 l/h at 150 psi
    PERMAQ2-4018 S HF, 1000 l/h at 150 psi
    PERMAQ2-4021 S, 1000 l/h at 150 psi
    PERMAQ2-4021 S HF, 1000 l/h at 150 psi
    PERMAQ2-4040, 1000 l/h at 150 psi
    PERMAQ2R-4040, 1000 l/h at 150 psi
    PERMAQ2R-4040 S HF, 1500 l/h at 150 psi
    PERMAQ2-8040 W, 1000 l/h at 150 psi
    PERMAQ2-8040 HF, 1000 l/h at 150 psi
    PERMAQ3-4018, 1000 l/h at 150 psi
    PERMAQ3-4018 HF, 1000 l/h at 150 psi
    PERMAQ3-4021, 1000 l/h at 150 psi
    PERMAQ3-4021 HF, 1000 l/h at 150 psi
    PERMAQ3-4040, 1000 l/h at 150 psi
    PERMAQ3-4040 HF, 1000 l/h at 150 psi
    PERMAQ3-4611, 1000 l/h at 150 psi
    PERMAQ3-4641, 1500 l/h at 150 psi
    PERMAQ3-8040, 1500 l/h at 150 psi
    PERMAQ4-4021, 1000 l/h at 100 psi
    PERMAQ4-4018 HF, 1000 l/h at 100 psi
    PERMAQ4-4029 HF, 1000 l/h at 100 psi
    PERMAQ4-4021 HF, 1000 l/h at 100 psi
    PERMAQ4-4040 HF, 1000 l/h at 100 psi
    PERMAQ4-4040, 1000 l/h at 100 psi
    PERMAQ4-4040 S HF, 1000 l/h at 100 psi
    PERMAQ4-4040 W, 1000 l/h at 100 psi
    PERMAQ4-8040 W, 1000 l/h at 100 psi
    PERMAQ7-4021, 1500 l/h at 500 psi
    PERMAQ7-4040, 1500 l/h at 500 psi
    PERMAQ8-4021, 1500 l/h at 500 psi
    PERMAQ8-4040, 1500 l/h at 500 psi
    PERMAQ8-8040, 15000 l/h at 500 psi
[4] Certified elements must be flushed of preservative in the field for a minimum of 1 hour
    at the following parameters:
    PERMAQ1-4014 HF, 12,610 l/h at 150 psi
    PERMAQ1-4018 , 13,890 l/h at 150 psi
    PERMAQ2-4014 HF, 9745 l/h at 150 psi
    PERMAQ2-4018, 12,610 l/h at 150 psi
    PERMAQ3-4014 HF, 14,725 l/h at 150 psi
    PERMAQ4-4014 HF, 12,610 l/h at 100 psi
    PERMAQ4-4018 , 13,890 l/h at 100 psi
    PERMAQ2R-8040, 9745 l/h at 150 psi
    PERMAQ2-8040, 9745 l/h at 150 psi
    PERMAQ2-4611, 12,610 l/h at 150 psi
    PERMAQ5-8040 -2, 10,530 l/hr at 225 psi
    PERMAQ5-8040 -3, 11,555 l/hr at 225 psi
    PERMAQ1-8040 HF, 12,000 l/ hr at 150 psi
    PERMAQ2-4641, 12,000 l/h at 100 psi
    PERMAQ4-8040 HF, 12,000 l/h at 100 psi
[5] All models are certified to a minimum daily flow of 1,737 liters per day. All models
    must be flushed of preservative in the field for a minimum of 2 hours at a flow rate of
    1,000 l/h at 150 psi.

[G] Product is Certified to NSF/ANSI/CAN 372 and conforms with the lead content requirements
    for "lead free" plumbing as defined by California, Vermont, Maryland, and Louisiana
    state laws and the U.S. Safe Drinking Water Act.
[Q] This product meets the reduced Q test statistic criteria of 1 µg for lead per Section
    9.5.1.1 of NSF/ANSI/CAN 61.

[Q] This product meets the reduced Q test statistic criteria of 1 ug or 0.5 ug for lead per
    Section 9.5.1.1 of NSF/ANSI/CAN 61.

[1] Valves are named as follows: W A B CDE F G H I WXX, where:
       
    W   -  Series W Valve
    A - Inlet
        2 - MOULD BODY WITH 3/4" INLET, 3/4"(OUTPUT PUSHFIT)
        A - MOULD WATER VALVE FITTINGS MALE 180°, G ¾”
        B - MOULD WATER VALVE FITTINGS MALE 180°, G ½”
        C - MOULD WATER VALVE FITTINGS MALE 180°, G 3/8"
        D - MOULD WATER VALVE FITTINGS MALE 180° CUSTOMIZE FOR KEURIG 180°, 3/4"
        F - MOULD WATER VALVE FITTINGS MALE 90°, G ½”
        G - MOULD WATER VALVE FITTINGS MALE 90°, G ¾”
        L - MOULD WATER VALVE FITTINGS, Push fit Ø6mm
        M - MOULD WATER VALVE FITTINGS, Push fit Ø8mm
        N - MOULD WATER VALVE FITTINGS, Push fit Ø10mm
        P - MOULD WATER VALVE FITTINGS, Push fit Ø1/4”
        R - MOULD WATER VALVE FITTINGS, Push fit Ø3/8”
        0 - ONLY PILOT, NO BODY
    B - Outlet
        2 - MOULD BODY WITH 3/4" INLET, JG6mm
        3 - MOULD BODY WITH 3/4" INLET, JG10mm
        4 - MOULD BODY WITH 3/4" INLET, JG8mm
        7 - MOULD BODY WITH 3/4" INLET, JG1/4”
        A - MOULD WATER VALVE FITTINGS MALE 180°, G 3/4"
        B - MOULD WATER VALVE FITTINGS MALE 180°, G 1/2"
        C - MOULD WATER VALVE FITTINGS MALE 180°, G 3/8"
        F - MOULD WATER VALVE FITTINGS MALE 90°, G 1/2"
        L - MOULD WATER VALVE FITTINGS, Push fit Ø6mm
        M - MOULD WATER VALVE FITTINGS, Push fit Ø8mm
        N - MOULD WATER VALVE FITTINGS, Push fit Ø10mm
        P - MOULD WATER VALVE FITTINGS, Push fit Ø1/4”
        R - MOULD WATER VALVE FITTINGS, Push fit Ø3/8”
        0 - ONLY PILOT, NO BODY
    CDE - DN mm 00,0
           100 -  10 mm
    F   -  FLOW RESTRICTOR
           0 -  WITHOUT
           1 -  (1,2) liters
           2 -  (2,2) liters
    G   -  FLOW REGULATOR
           0 -  WITHOUT
    H   -  FILTER
           0 -  WITHOUT
           1 -  80 mesh
           2 -  150 mesh
           3 -  Check Valve
    I   -  CUSTOMIZATION
           0 -  WITHOUT
           1 -  WITH (SPECIAL EXECUTION
           3 -  NEEDLE
    WXX -  COIL
[2] Series W valves are solenoid valves intended for use with hot water dispensers up to 65
    degrees Celsius.
[G] Product is Certified to NSF/ANSI/CAN 372 and conforms with the lead content requirements
    for "lead free" plumbing as defined by California, Vermont, Maryland, and Louisiana
    state laws and the U.S. Safe Drinking Water Act.

[Q] This product meets the reduced Q test statistic criteria of 1 ug or 0.5 ug for lead per
    Section 9.5.1.1 of NSF/ANSI/CAN 61.

[3] L   - Series L Valve
    AAA - Version
    400 - Body thread M20*1
    500 - Body thread M22*2
    BB  - Seat Diameter
    50  - 5 mm
    CC  - Kind of Seals
    LS  - LSR Liquid Silicone
    P   - Plastic Body
    DD  - Special Execution
    EEE - Coil Type
[G] Product is Certified to NSF/ANSI/CAN 372 and conforms with the lead content requirements
    for "lead free" plumbing as defined by California, Vermont, Maryland, and Louisiana
    state laws and the U.S. Safe Drinking Water Act.

[Q] This product meets the reduced Q test statistic criteria of 1 ug or 0.5 ug for lead per
    Section 9.5.1.1 of NSF/ANSI/CAN 61.

[1] Valves are named as follows: VJ XX YY ZZZ P WWW KKKK
    
    SERIES
    V - Fixed
    J - 3 for 3 way
    7 for 2 way
    
    VERSION
    XX - Sequential number for hydraulic connections
         (in V3 models) - 18, 19, 30, 40, 53, 54, 55, 70, 73, 82, 83, 91, 92, 93, 95, 97, 99
         (in V7 models) - 19, 30, 31, 39, 40, 42, 43, 44, 45, 70, 82, 91, 93, 95, 99
      
    KIND OF SEALING
    YY - LS for LSR liquid silicone
    VN for Silicone neutral
    EN for EPDM black
                      
    SEAT DIAMETER - Two or three digits
    ZZ or ZZZ - Internal fluid passage diameter
                (in V3 models ) - 10, 12, 15, 20, 25, 26, 27
                (in V7 models) - 10, 12, 15, 20, 25
                    
    BODY TREATMENT
    P - Plastic body
    
    SPECIAL EXECUTION - Not in contact with water
    WWW - In case of NO special execution NO digit
                  
    STANDARD COIL - Not in contact with water
    KKKK          - It depends on type of coil.
[G] Product is Certified to NSF/ANSI/CAN 372 and conforms with the lead content requirements
    for "lead free" plumbing as defined by California, Vermont, Maryland, and Louisiana
    state laws and the U.S. Safe Drinking Water Act.

[1] Approved control options include handle, gearbox, electric, and pneumatic.

[1] Colors: Red brown, off-white
    Number of Coats: 1-2
    Sequence of Coats: 1 coat application: off-white; 2 coat application: red brown then
    off-white
    Maximum Field Use Dry Film Thickness (in mils): 24 (max 12 per coat)
    Recoat Cure Time and Temperature: 32 hours at 20°C
    Final Cure Time and Temperature: 7 days at 23°C
    Special Comments: Mix ratio of Part A:Part B is 88:12 by weight or 81:19 by volume.
    Curing should occur under continuous ventilation.

[1] Colors: Red brown, off-white
    Number of Coats: 1-2
    Sequence of Coats: 1 coat application: off-white; 2 coat application: red brown then
    off-white
    Maximum Field Use Dry Film Thickness (in mils): 24 (max 12 per coat)
    Recoat Cure Time and Temperature: 32 hours at 20°C
    Final Cure Time and Temperature: 7 days at 23°C
    Special Comments: Mix ratio of Part A:Part B is 88:12 by weight or 81:19 by volume.
    Curing should occur under continuous ventilation.

[1] Colors: Red brown, off-white
    Number of Coats: 1-2
    Sequence of Coats: 1 coat application: off-white; 2 coat application: red brown then
    off-white
    Maximum Field Use Dry Film Thickness (in mils): 24 (max 12 per coat)
    Recoat Cure Time and Temperature: 32 hours at 20°C
    Final Cure Time and Temperature: 7 days at 23°C
    Special Comments: Mix ratio of Part A:Part B is 88:12 by weight or 81:19 by volume.
    Curing should occur under continuous ventilation.

[1] Certified for a maximum surface area to volume ratio of 80 sq. in./L.

[1] Pipe and Fitting end use

[1] Certified for a maximum surface area to volume ratio of 2.0 sq. in./L
[2] This product has also been evaluated for use in Mechanical Plumbing Device applications
    with a maximum use restriction of 2.0 sq. in./L.
[3] Certified for a maximum suface area to volume ratio of 20 sq. in./L.
[G] Product is Certified to NSF/ANSI/CAN 372 and conforms with the lead content requirements
    for "lead free" plumbing as defined by California, Vermont, Maryland, and Louisiana
    state laws and the U.S. Safe Drinking Water Act.

[1] Certified for a maximum surface area to volume ratio of 2.0 sq. in./L
[2] This product has also been evaluated for use in Mechanical Plumbing Device applications
    with a maximum use restriction of 2.0 sq. in./L.
[3] Certified for a maximum suface area to volume ratio of 20 sq. in./L.
[G] Product is Certified to NSF/ANSI/CAN 372 and conforms with the lead content requirements
    for "lead free" plumbing as defined by California, Vermont, Maryland, and Louisiana
    state laws and the U.S. Safe Drinking Water Act.

[1] Certified for a maximum surface area to volume ratio of 2.0 sq. in./L
[2] This product has also been evaluated for use in Mechanical Plumbing Device applications
    with a maximum use restriction of 2.0 sq. in./L.
[3] Certified for a maximum suface area to volume ratio of 20 sq. in./L.
[G] Product is Certified to NSF/ANSI/CAN 372 and conforms with the lead content requirements
    for "lead free" plumbing as defined by California, Vermont, Maryland, and Louisiana
    state laws and the U.S. Safe Drinking Water Act.

[1] Sizes indicated are expressed as diameter x length.
[2] Certified for a minimum permeate (product water) flow of 1,191 L/day.
[3] Certified elements must be flushed of preservative in the field for a minimum of 2 hours
    at the following parameters:
    Membrania OceanFlow HR at 12000 l/h at 500 psi	
    Membrania OceanFlow HR Plus at 12000 l/h at 500 psi
    Membrania OceanFlow HR 4040 at 1500 l/h at 500 psi	
    Membrania OceanFlow HF	 at 15000 l/h at 500 psi
    Membrania OceanFlow HF Plus at 15000 l/h at 500 psi
    Membrania OceanFlow HF 4040 at 1500 l/h at 500 psi

[1] This product is Certified for a maximum use level of 125 mg/L.
[G] Product is Certified to NSF/ANSI/CAN 372 and conforms with the lead content requirements
    for "lead free" plumbing as defined by California, Vermont, Maryland, and Louisiana
    state laws and the U.S. Safe Drinking Water Act.

[1] Certified for a maximum surface area to volume ratio of 2.0 sq. in./L.

[1] Certified for a maximum surface area to volume ratio of 2.0 sq. in./L.

[1] Size is expressed as suction end x discharge end.
[2] A - Motor Speed
        None - 2 Pole (300 rpm)
        F    - 4 Pole (1800 rpm)
    B - Pump Configuration
        None - Vertical
        H    - Horizontal
    C - Working Pressure
        None - Standard
        P    - Uprated 
    F - Piping Connection Type
        F - Round flange
        N - Oval flange
        L - Loose round flange
        V - Victaulic
        C - Clamp
    W - Number of Impellers
        1 - 29
    X - Horsepower of Motor
        0050 - 1/2 hp
        0075 - 3/4 hp
        0100 - 1.0 hp
        0150 - 1.5 hp
        0200 - 2.0 hp
        0300 - 3.0 hp
        0500 - 5.0 hp
        0750 - 7.5 hp
        1000 - 10 hp
        1500 - 15 hp
        2000 - 20 hp
        2500 - 25 hp
        3000 - 30 hp
        4000 - 40 hp
        5000 - 50 hp
    Y - Motor Type
        D - Open drip proof (ODP)
        T - Totally enclosed fan cooled (TEFC)
        W - Washdown Motor Enclosure
        X - Explosion Proof Motor Enclosure
    Z - Motor phase
        1 - Single phase
        3 - Three phase
    
    "A" in the model name indicates sub-component design modifications.
    
    Only the type "S" mechanical seal (Silicon Carbide/Carbon/FPM) is included in
    Certification.
[3] A - Pump Configuration
        None - Vertical
        H    - Horizontal
    B - Working Pressure
        None - Standard
        P    - Uprated
    W - Number of impellers (1-10)
    R - Number of reduced diameter impellers (0-10)
    X - Horsepower of motor
        0050 - 1/2HP
        0075 - 3/4HP
        0100 - 1.0HP
        0150 - 1.5HP
        0200 - 2.0 HP
        0300 - 3.0 HP
        0500 - 5.0 HP
        0750 - 7.5 HP
        1000 - 10 HP
        1500 - 15 HP
        2000 - 20 HP
        2500 - 25 HP
        3000 - 30 HP
        4000 - 40 HP
        5000 - 50 HP
        6000 - 60 HP
        7500 - 75 HP
    Y - Motor Type
        D - Open Drip Proof (ODP)
        T - Totally Enclosed Fan Cooled (TEFC)
        W - Washdown Motor Enclosure
        X - Explosion Proof Motor Enclosure
    Z - Motor phase
        1 - Single phase
        3 - Three phase
[G] Product is Certified to NSF/ANSI/CAN 372 and conforms with the lead content requirements
    for "lead free" plumbing as defined by California, Vermont, Maryland, and Louisiana
    state laws and the U.S. Safe Drinking Water Act.

[1] This product has also been evaluated for use in Mechanical Plumbing Device applications
    with a maximum surface area to volume ratio of 5.6 sq. in./L.
[2] This product has also been evaluated for use in Mechanical Plumbing Device applications
    with a maximum surface area to volume ratio of 2.0 sq. in./L.
[3] This product has also been evaluated for use in Mechanical Plumbing Device applications
    with a maximum surface area to volume ratio of 10 sq. in./L.
[4] This product is Certified for the following colors:
    Transparent (no color), White, Black, Red, Red 3000, Blue, Yellow, Light green, Dark
    green, Light grey, and Dark grey
    Numbers /20 to /80 in the Trade Designation represent the shore hardness

[1] This product has also been evaluated for use in Mechanical Plumbing Device applications
    with a maximum surface area to volume ratio of 5.6 sq. in./L.
[2] This product has also been evaluated for use in Mechanical Plumbing Device applications
    with a maximum surface area to volume ratio of 2.0 sq. in./L.
[3] This product has also been evaluated for use in Mechanical Plumbing Device applications
    with a maximum surface area to volume ratio of 10 sq. in./L.
[4] This product is Certified for the following colors:
    Transparent (no color), White, Black, Red, Red 3000, Blue, Yellow, Light green, Dark
    green, Light grey, and Dark grey
    Numbers /20 to /80 in the Trade Designation represent the shore hardness

[1] This certification includes NSF-61 Section 9 for Cold/Ambient temperature water
    pathways. The sparkling water pathway is not evaluated to NSF-61.
[2] The maximum operating temperature of these units is 74 F/23°C.
[G] Product is Certified to NSF/ANSI/CAN 372 and conforms with the lead content requirements
    for "lead free" plumbing as defined by California, Vermont, Maryland, and Louisiana
    state laws and the U.S. Safe Drinking Water Act.
[Q] This product meets the reduced Q test statistic criteria of 1 µg or 0.5 µg for lead per
    Section 9.5.1.1 of NSF/ANSI/CAN 61.

[1] Naming convention: e-Watercontrol code 10(2)1370(2)(1)			
    (1) 2 digits (characters or numbers) for customization			
    (2) 1 possible character "." for customization
[G] Product is Certified to NSF/ANSI/CAN 372 and conforms with the lead content requirements
    for "lead free" plumbing as defined by California, Vermont, Maryland, and Louisiana
    state laws and the U.S. Safe Drinking Water Act.

[1] S124= TOPIC Family ball valves
    x = lever options and valves connection: (numbers from 1 to 9)
    y = Type connection: V, D, W, J, P, T, C, I, K, Z
    zz = sizes (in yellow 92-90) ; in blu (13-23)
    92 = 1/4’’ NPT
    93 = 3/8” NPT
    94 = 1/2" NPT
    95 = 3/4” NPT
    96 = 1” NPT
    97 = 1 1/4" NPT
    98 = 1 1/2” NPT
    99 = 2” NPT
    88 = 2 1/2" NPT
    89 = 3” NPT
    90 = 4” NPT
    13 = 1/4’’ PRESS or SOLDER or PEX or COMPRESSION
    14 = 3/8” PRESS or SOLDER or PEX or COMPRESSION
    15 = 1/2" PRESS or SOLDER or PEX or COMPRESSION
    16 = 3/4” PRESS or SOLDER or PEX or COMPRESSION
    17 = 1” PRESS or SOLDER or PEX or COMPRESSION
    18 = 1 1/4" PRESS or SOLDER or PEX or COMPRESSION
    19 = 1 1/2” PRESS or SOLDER or PEX or COMPRESSION
    20 = 2” PRESS or SOLDER or PEX or COMPRESSION
    21 = 2 1/2" PRESS or SOLDER or PEX or COMPRESSION
    22 = 3” PRESS or SOLDER or PEX or COMPRESSION
    23 = 4” PRESS or SOLDER or PEX or COMPRESSION
    w = alphanumeric character. Options:
    L = with lockable lever
    0 – 9 = customization / lever color, packaging or marking
    A – Z = customization / lever color, packaging or marking
[G] Product is Certified to NSF/ANSI/CAN 372 and conforms with the lead content requirements
    for "lead free" plumbing as defined by California, Vermont, Maryland, and Louisiana
    state laws and the U.S. Safe Drinking Water Act.

[G] Product is Certified to NSF/ANSI/CAN 372 and conforms with the lead content requirements
    for "lead free" plumbing as defined by California, Vermont, Maryland, and Louisiana
    state laws and the U.S. Safe Drinking Water Act.

[G] Product is Certified to NSF/ANSI/CAN 372 and conforms with the lead content requirements
    for "lead free" plumbing as defined by California, Vermont, Maryland, and Louisiana
    state laws and the U.S. Safe Drinking Water Act.

[3] Models that have an inner diameter of 10 mm (DN10)
    DN10K, DN10S
    Fittings: F1/2, F3/8, F9/16, F 1/2NPSM, F3/4, F3/4NPSM, F3/4NH 
    DN10KL, DN10KZ, DN10SL
    Fittings: F1/2, F3/8, F9/16, F1/2NPSM, F3/4, F3/4NPSM, F3/4NH, M1/2NPT
[4] Models that have an inner diameter of 12.5 mm (DN13)
    Fittings: F1/2, F1/2NPSM, F3/4, F3/4NPSM, F3/4NH
[5] Connectors have an inner diameter of 6 mm (DN6)
    DN6K, DN6S, DN6X
    Fittings: F ½ c/gom, F15x1, F3/8, F3/8 c/gom, FIP ½, O9.5 C.O. compression, 010 C.O.
    compression, 010 C.G. compression, 15x1 Male, FC1/2 Female, FM1/4 NPSM Female, F1/2
    Female, Cod. ½(xFC1/2), F9/16 c/gom Female, 8x1C Male, 10x1C Male, 12x1P Male,
    14x1Male, F14x1 Female, 15x1Gir
    
    DN6KL, DN6KZ, DN6SL, DN6XL, DN6XZ, P6KL, P6KZ, P6SL
    Fittings: 8x0,75 HR Male, T8, M1/2, F3/8 Bend, F1/2 Bend, F15x1, F3/8, F3/4 NH c/gom,
    F3/8 c/gom, FIP ½, M1/2 NPT, T10 “Tube”, ½, O9.5 C.O. compression, 010 C.O.
    compression, 010 C.G. compression, 15x1 Male, FC1/2 Female, FM1/4 NPSM, FCAM ½ Female,
    FCA ½ Female, F1/2 Female, Cod. ½ (xFC1/2), Cod. 1/2GIR (XFCA1/2), F9/16 Female, F9/16
    Female c/gom, 8x1C Male, 8x1L Male, 10x1C Male, 10x1L Male, 10x1 LAV Male, 11x1CC
    Male, 11x1Z Male, 12x1P Male, 14x1 Male, 15x1V Male, 15x1Gir Male, M3/8, IRF + IRB*,
    F1/2 c/gom, F14x1 Female
    
    P6K, P6S
    Fittings: F1/2 c/gom, F15x1, F3/8, F3/8 c/gom, FIP ½, O9.5 C.O. compression, 010
    C.O. compression, 010 C.G. compression, 15x1 Male, FC1/2 Female, FM1/4 NPSM, FCAM ½
    Female, FCA ½ Female, F1/2 Female, Cod. ½ (xFC1/2), Cod. 1/2GIR (XFCA1/2), F9/16
    Female, F9/16 Female c/gom, 8x1C Male,10x1C Male, 11x1CC Male, 11x1Z Male, 12x1P
    Male, 14x1 Male, F14x1 Female, 15x1V Male, 15x1Gir Male, M3/8, IRF + IRB*
    
    *Note: Connectors combined using the IRF + IRB connection fitting must remain within
    the listed minimum and maximum length restrictions.
[6] Connectors have an inner diameter of 8 mm (DN8)
    
    DN8K, DN8S, DN8X
    Fittings: F ½ c/gom, F15x1, F3/8, F3/8 c/gom, FIP ½, O9.5 C.O. compression, 010 C.O.
    compression, 010 C.G. compression, 15x1 Male, FC1/2, FM1/4 NSPM Female, FCAM ½ Female,
    FCA ½ Female, F1/2 Female, Cod. ½ (xFC1/2), Cod. 1/2GIR (XFCA1/2), T8, F9/16 Female,
    F9/16 c/gom Female, 8x1C Male, 10x1C Male, 11x1CC Male, 11x1Z male, 12x1P Male, 14x1
    Male, F14x1 Female, 15x1Gir Male
    
    DN8KL, DN8KZ, DN8SL, DN8XL, DN8XZ, DPV8KL, DPV8KZ, DPV8SL, P9KL, P9KZ, P9SL
    Fittings: 10x1 HR Male, M1/2, NPB ½ Male, F3/8 Bend, F1/2 Bend, F1/2 c/gom, F15x1,
    F3/8, F3/4 NH C/gom, F3/8 c/gom, FIP ½, M ½ NPT, T8, T10 “Tube”, O9.5 C.O.
    compression, 010 C.O. compression, 010 C.G. compression, 15x1 Male, FC1/2, FM1/4 NSPM
    Female, FCAM ½ Female, FCA ½ Female, F1/2 Female, Cod. ½ (xFC1/2), Cod. 1/2GIR
    (XFCA1/2), F9/16 Female, F9/16 c/gom Female, 10x1C Male, 10x1L Male, 10x1 LAV (not to
    be used with 10x1L Male), 11x1CC Male, 11x1Z, 12x1P, 14x1 Male, F14x1 Female, 15x1V
    Male, 15x1Gir, T 9.5, M3/8, IRF + IRB*
    
    DPV8K, DPV8S, P9K, P9S
    Fittings: F1/2 c/gom, F15x1, F3/8, F3/8 c/gom, FIP ½, O9.5 C.O. compression, 010
    C.O. compression, 010 C.G. compression, 15x1 Male, FC1/2, FM1/4 NSPM Female, FCAM ½
    Female, FCA ½ Female, F1/2 Female, Cod. ½ (xFC1/2), Cod. 1/2GIR (XFCA1/2), T8, F9/16
    Female, F9/16 c/gom, 8x1C Male, 10x1C Male, 11x1CC Male, 11x1Z Male, 12x1P Male, 14x1
    Male, F14x1 Female, 15x1V Male, 15x1Gir Male, M3/8, IRF + IRB*
    
    *Note: Connectors combined using the IRF + IRB connection fitting must remain within
    the listed minimum and maximum length restrictions

[1] All products have trade names that contain the following descriptors that appear in the
    following order ABCDEF:
    
    A. External Covering:
    DN – Stainless Steel Braiding
    DPV – Stainless Steel Braiding with rubber coating
    P - Nylon
    
    B. Internal Diameters:
    6 - DN6
    8 – DN8
    9 – DN8
    10 – DN10
    13 – DN13
    
    C. Inliner Material:
    K - Silicone
    S - EPDM
    X – PE
    
    D. End Connection Material Type: Blank, L, or Z
    
    E. Fittings:
    Fitting options as follows: see [2] [3] [4] [5]
[2] F. Length
    Maximum Length Restrictions are as follows:
    Flexible Connector Hose models made with material K:
    DN6 – 2500 mm (98 in)
    DN8 – 2032 mm (80 in)
    DN10 – 1600 mm (63 in)
    DN13 – 1250 mm or (49 in)
        
    Flexible Connector Hose models made with material S:
    DN6 – 2032mm (80 in)
    DN8 – 1524mm (60 in)
    DN10 – 1194 mm (47 in)
    DN13 – 914 mm (36 in)
       
    Flexible Hose models made with material X:
    DN6 – 2032mm (80 in)
    DN8 – 1524mm (60 in)
       
    Minimum Length Restrictions:
    All trade names, except those ending in L or Z, are subject to the following minimum
    length restrictions:
    DN6 - 459 mm (18 in)
    DN8 - 440 mm (17.3 in)
    P6 - 764 mm (30 in)
    P9, DPV8 - 573 mm (22.5 in)
    DN10, DN13 - 320 mm (12.6 in)
         
    Models using end connections with L or Z in the name do not have minimum length
    restrictions.
[G] Product is Certified to NSF/ANSI/CAN 372 and conforms with the lead content requirements
    for "lead free" plumbing as defined by California, Vermont, Maryland, and Louisiana
    state laws and the U.S. Safe Drinking Water Act.
[Q] This product meets the reduced Q test statistic criteria of 1 µg or 0.5 µg for lead per
    Section 9.5.1.1 of NSF/ANSI/CAN 61.

[1] Pipe manufactured of this material is cure process dependent. Use of this
    material in NSF Certified Pipe requires NSF's prior authorization.

[1] S  - mounting feature
         0 - standard paddlewheel sensor
         1 - paddlewheel sensor for compact mounting
    T  - Technology of electronic transmission
         H - hall effect
         C - coil
         P - push-pull
    X  - Flow functionality
         0 - bidirectional standard sized FLS F3.0 model
         3 - mono-directional
    YZ - Number indication materials (sensor & gasket)
         09, 10, 11, 12, 38, 40 - mono and bi directional magmeters
         01 - hot tap magmeter and high pressure paddlewheel sensor
         01 thru 24 - paddlewheel sensor
         01 thru 12 - flow switch, paddlewheel transmitter and paddlewheel sensor for
    compact mounting
[G] Product is Certified to NSF/ANSI/CAN 372 and conforms with the lead content requirements
    for "lead free" plumbing as defined by California, Vermont, Maryland, and Louisiana
    state laws and the U.S. Safe Drinking Water Act.

[1] S  - mounting feature
         0 - standard paddlewheel sensor
         1 - paddlewheel sensor for compact mounting
    T  - Technology of electronic transmission
         H - hall effect
         C - coil
         P - push-pull
    X  - Flow functionality
         0 - bidirectional standard sized FLS F3.0 model
         3 - mono-directional
    YZ - Number indication materials (sensor & gasket)
         09, 10, 11, 12, 38, 40 - mono and bi directional magmeters
         01 - hot tap magmeter and high pressure paddlewheel sensor
         01 thru 24 - paddlewheel sensor
         01 thru 12 - flow switch, paddlewheel transmitter and paddlewheel sensor for
    compact mounting
[G] Product is Certified to NSF/ANSI/CAN 372 and conforms with the lead content requirements
    for "lead free" plumbing as defined by California, Vermont, Maryland, and Louisiana
    state laws and the U.S. Safe Drinking Water Act.

[2] Certified for equivalent metric sizes.
    DualBlock TKD,LKD(X)(Y)(Z)
    X - End connection type
        IC AC NC FC IM DM FM OM OAM BM
    Y - Size
        Imperial (inches)
        012 034 038 100 112 114 200
        Metric (mm)
        016 020 025 032 040 050 063
    Z - O-ring type
        E - EPDM o-ring F - FPM o-ring
    DualBlock VKD(X)(Y)(Z)
    X - End Connection Type
        IC AC NC DC OC OAC FC IM DM FM OM OAM BM
    Y - Size
        Imperial (inches)
        012 034 038 100 112 114 200 212 300 400
        Metric (mm)
        016 020 025 032 040 050 063 075 090 110
    Z - O-ring type
        E - EPDM o-ring F - FPM o-ring
    /SHX - non-wetted stainless steel fasteners (optional)
    Easyfit VXE(X)(Y)(Z)
    X - End Connection Type
        IC AC NC FC
    Y - Size
        Imperial (inches)
        012 034 038 100 112 114 200 212 300 400
        Metric (mm)
        016 020 025 032 040 050 063 075 090 110
    Z - O-ring type
        E - EPDM o-ring F - FPM o-ring
    VX(X)(Y)(Z)
    X - End Connection Type
        IC AC NC FC
    Y - Size
        Imperial (inches)
        212 300 400
        Metric (mm)
        075 090 110
    Z - O-ring type
        E - EPDM o-ring F - FPM o-ring
    Easyfit SXE(X)(Y)(Z)
    X - End Connection Type
        IC, AC, NC, FC
    Y - Size 
        Imperial (inches)
        038 012 034 100 114 112 200 212 300 400
        Metric (mm)
        016 020 025 032 040 050 063 075 090 110
    Z - O-ring type
        E - EPDM F - FPM
    DualBlock VKR(X)(Y)(Z)
    X - End connection type
        IC DC LC FC AC NC JC GC OC OAC IM DM FM OM OAM BM
    Y - Size
        Imperial (inches)
        038 012 034 100 114 112 200
        Metric (mm)
        016 020 025 032 040 050 063
    Z - O-ring type
        E - EPDM o-ring F - FPM o-ring
    
    
[3] Certified for equivalent metric sizes.
    VE, VX
    X - End connection type
        IV FV LV AV NV JV GV
    Y - Size
        Imperial (inches)
        212 300 400
        Metric (mm)
        075 090 110 
    Z - O-ring type
        E - EPDM F - FPM
    VEE
    X - End Connection Type
        IV FV LV AV NV JV GV
    Y - Size 
        Imperial (inches)
        012 034 038 100 114 112 200 212 300 400
        Metric (mm)
        016 020 025 032 040 050 063 075 090 110
    Z - O-ring type
        E - EPDM F - FPM
    VKD
    X - End Connection Type
        IV FV LV AV NV JV GV/SHX IM DM FM OM OAM BM/SHX
    Y - Size
        Imperial (inches)
        038 012 034 100 114 112 200 212 300 400
        Metric (mm)
        016 020 025 032 040 050 063 075 090 110 
    Z - O-ring type
        E - EPDM F - FPM
    VXE
    X - End Connection Type
        IV DV FV LV AV NV JV GV
    Y - Size
        Imperial (inches)
        038 012 034 100 114 112 200 212 300 400
        Metric (mm)
        016 020 025 032 040 050 063 075 090 110
    Z - O-ring type
        E - EPDM F - FPM
    TKD, LKD
    X - End Connection Type
        AV DV FV GV IV JV LV NV IM DM FM BM OM OAM
    Y - Size
        Imperial (inches)
        038 012 034 100 114 112 200
        Metric (mm)
        016 020 025 032 040 050 063
    Z - O-ring type
        E - EPDM F - FPM
    SXE
    X - End Connection Type
        AV DV FV GV IV JV LV NV
    Y - Size Imperial (inches)
        038 012 034 100 114 112 200 212 300 400
        Metric (mm)
        016 020 025 032 040 050 063 075 090 110
    Z - O-ring type
        E - EPDM F - FPM
    VKR
    X - End connection type
        IV DV LV FV AV NV JV GV OV OAV IM DM FM OM OAM BM
    Y - Size
        Imperial (inches)
        038 012 034 100 114 112 200
        Metric (mm)
        016 020 025 032 040 050 063
    Z - O-ring type
        E - EPDM F - FPM
[4] FE (X)(T)(Y) (Z) (W)   
    X  - End connection type
    O  - Flanged ISO type
    OA - Flanged ANSI type
    T  - Disc Material PVC-U
    W  - Actuation type
         FM, LM, RM,CE, CP
    Y  - Size
         Metric (mm)
         050 063 075 090 110 140 160 225 280 315 355 400
         Imperial (inches)
         112, 200, 212 300 400 500 600 800 810 812 814 816
    Z  - Gasket type
    E  - EPDM
[5] FK (X)(T)(Y) (Z) (W)
    X   - End connection type
    O   - Flanged ISO type
    OA  - Flanged ANSI type
    OL  - Flanged lug ISO type
    OAL - Flanged lug ANSI type
    T   - Disc material PVC-U, PVC-C and PP-H
    W   - Actuation type
          FM, LM, RM, CE, CP
    Y   - Size
          Metric (mm)
          050 063 075 090 110 140 160 225 280 315 355 400
          Imperial (inches)
          112 200 212 300 400 500 600 800 810 812 814 816
    Z   - Gasket type
    E   - EPDM
[6] FK (X)(T)(Y) (Z) (W)
    X   - End connection type
    O   - Flanged ISO type
    OA  - Flanged ANSI type
    OL  - Flanged lug ISO type
    OAL - Flanged lug ANSI type
    T   - Disc Material PVC-C and PP-H
    W   - Actuation type
          FM, LM, RM,CE, CP
    Y   - Size
          Metric (mm)
          050 063 075 090 110 140 160 225 280 315 355 400
          Imperial (inches)
          112, 200, 212 300 400 500 600 800 810 812 814 816
    Z   - Gasket type
    E   - EPDM
[7] FX (X)(T)(Y) (Z) (W)
    X   - End connection type
    O   - Flanged ISO type
    OA  - Flanged ANSI type
    OL  - Flanged lug ISO type
    OAL - Flanged lug ANSI type
    W   - Actuation type
          FM, LM, RM,CE, CP
    Y   - Size
          Metric
          (mm) 050 063 075 090 110 140 160 225 280 315 355 400
          Imperial (inches)
          112,200,212 300 400 500 600 800 810 812 814 816
    Z   - Gasket type
    E   - EPDM
    T   - Disc Material PP-H
[G] Product is Certified to NSF/ANSI/CAN 372 and conforms with the lead content requirements
    for "lead free" plumbing as defined by California, Vermont, Maryland, and Louisiana
    state laws and the U.S. Safe Drinking Water Act.

[G] Product is Certified to NSF/ANSI/CAN 372 and conforms with the lead content requirements
    for "lead free" plumbing as defined by California, Vermont, Maryland, and Louisiana
    state laws and the U.S. Safe Drinking Water Act.

[1] This product is also evaluated for use in Mechanical Plumbing Device applications with a
    maximum use restriction of 10.0 sq. in./L.
[2] Certified for a maximum surface area to volume of 10 sq. in./L.

[1] This product is also evaluated for use in Mechanical Plumbing Device applications with a
    maximum use restriction of 10.0 sq. in./L.
[2] Certified for a maximum surface area to volume of 10 sq. in./L.

[1] The F101ASG Kit include tankless water heater inlet valves (F101AG) and tankless water
    heater outlet valves (F101SG).
[2] The T101ASG and S101ASG Kits include tankless water heater inlet valves (T101AG/S101AG)
    and tankless water heater outlet valves (T101SG/S101SG).
[3] The T101CASG and S101CASG Kits include tankless water heater inlet valves
    (T101CAG/S101CAG) and tankless water heater outlet valve (T101CSG/S101CSG).
[4] T90LF 1/2" is a single valve (not a part of a kit).
[G] Product is Certified to NSF/ANSI/CAN 372 and conforms with the lead content requirements
    for "lead free" plumbing as defined by California, Vermont, Maryland, and Louisiana
    state laws and the U.S. Safe Drinking Water Act.

[G] Product is Certified to NSF/ANSI/CAN 372 and conforms with the lead content requirements
    for "lead free" plumbing as defined by California, Vermont, Maryland, and Louisiana
    state laws and the U.S. Safe Drinking Water Act.

[1] Certified for a maximum surface area to volume ratio of 2.0 sq. in./L.
[2] Evaluated for use in Mechanical Plumbing Device applications with a maximum use
    restriction of 2.0 square inches/L.

[4] Trade names may include any of the following suffixes:
    D          - Distributor Bottom
    Open       - External tightness in Upper Body
    E.S.       - Mixing System for hot water economy
    LT         - External temperature limiter
    LPT        - Combination of external flow rate limiter and external temperature 
                 limiter
    C1         - Basic model for ECAU classification 
    C2         - Internal flow rate limiter 
    C3         - Combination of internal flow limiter and hot water economy 
    Antacid    - System to avoid detergent penetration
    +12/-12    - Lever Movement
    0/24       - Lever Movement
    O.R. Collo - Top external tightness
    O.R. Corpo - Middle External tightness

[Q] This product meets the reduced Q test statistic criteria of 1 µg or 0.5 µg for lead per
    Section 9.5.1.1 of NSF/ANSI/CAN 61.

[1] AA   - Model number/cartridge diameter (2, 11, 12, 13, 16, 17, 22, 35, 40, or m)
    BBBB - Flow, temperature, and noise reducer options (d, ECO, ES, A, LT, LPT, TEMP, PA
    and/or LP)
    NOTE:  Multiple BBBB suffix designations may be used

[Q] This product meets the reduced Q test statistic criteria of 1 µg or 0.5 µg for lead per
    Section 9.5.1.1 of NSF/ANSI/CAN 61.

[2] Product (Al2O3) was evaluated as a ceramic disk in faucets
[3] x - Numeric character
    z - Alphanumeric character

[Q] This product meets the reduced Q test statistic criteria of 1 µg or 0.5 µg for lead per
    Section 9.5.1.1 of NSF/ANSI/CAN 61.

[1] This product has also been evaluated for use in Mechanical Plumbing Device applications
    with a maximum use restriction of 4.0 sq. in./L.
[2] PTFE FE 1000 includes both finished parts machined by GAPI S.p.A and semi-finished PTFE
    shapes molded or extruded by GAPI S.p.A.  Parts machined from semi-finished PTFE shapes
    by entities other than GAPI S.p.A will not be NSF Certified and may not bear the NSF
    mark without prior authorization from NSF International.
[3] Only products bearing the NSF Mark on the product, product packaging, and/or
    documentation shipped with the product are Certified.
[4] Certified for a maximum surface area to volume ratio of 4.0 sq. in./L.

[G] Product is Certified to NSF/ANSI/CAN 372 and conforms with the lead content requirements
    for "lead free" plumbing as defined by California, Vermont, Maryland, and Louisiana
    state laws and the U.S. Safe Drinking Water Act.

[G] Product is Certified to NSF/ANSI/CAN 372 and conforms with the lead content requirements
    for "lead free" plumbing as defined by California, Vermont, Maryland, and Louisiana
    state laws and the U.S. Safe Drinking Water Act.

[1] All trade names may or may not include a dash before the LF suffix.
[G] Product is Certified to NSF/ANSI/CAN 372 and conforms with the lead content requirements
    for "lead free" plumbing as defined by California, Vermont, Maryland, and Louisiana
    state laws and the U.S. Safe Drinking Water Act.

[1] This product has also been evaluated for use in Mechanical Plumbing Device applications
    with a maximum use restriction of 7.75 sq. in./L.
[2] Certified for a maximum surface area to volume ratio of 7.75 sq. in./L.

[1] This product has also been evaluated for use in Mechanical Plumbing Device applications
    with a maximum use restriction of 7.75 sq. in./L.
[2] Certified for a maximum surface area to volume ratio of 7.75 sq. in./L.

[1] Mix ratio of Part A to Part B is 2.56:1 by weight.
[2] Certified for use as a potting material in hollow fiber filtration devices 4 inches in
    diameter and larger with a minimum daily flow of 500 Liters.

[1] xx - Packaging (empty or alphanumerical characters)
[G] Product is Certified to NSF/ANSI/CAN 372 and conforms with the lead content requirements
    for "lead free" plumbing as defined by California, Vermont, Maryland, and Louisiana
    state laws and the U.S. Safe Drinking Water Act.

[1] CODE "XXX" INSIDE ARTICLES CODE STANDS FOR "EXTERNAL FINISHES".
    FINISHES INCLUDED IN THIS LISTING:
    - CHROME (CODE: CR)
    - BRUSHED NICKEL (CODE: GN)
    - BRUSHED BRASS PVD (CODE: BBP)
    - BRUSHED COPPER PVD (CODE: BCP)
    - BRUSHED GUNMETAL PVD (CODE: BGP)
    - BRUSHED STEEL (CODE: IX)
[G] Product is Certified to NSF/ANSI/CAN 372 and conforms with the lead content requirements
    for "lead free" plumbing as defined by California, Vermont, Maryland, and Louisiana
    state laws and the U.S. Safe Drinking Water Act.
[Q] This product meets the reduced Q test statistic criteria of 1 µg or 0.5 µg for lead per
    Section 9.5.1.1 of NSF/ANSI/CAN 61.

[1] CODE "XXX" INSIDE ARTICLES CODE STANDS FOR "EXTERNAL FINISHES".
    FINISHES INCLUDED IN THIS LISTING:
    - CHROME (CODE: CR)
    - BRUSHED NICKEL (CODE: GN)
    - AGED IRON (CODE:AI)
    - BRUSHED BRASS (CODE: BB)
    - BRUSHED BRASS PVD (CODE: BBP)
    - BRUSHED COPPER PVD (CODE: BCP)
    - MATT BLACK PVD (CODE: MBP)
[G] Product is Certified to NSF/ANSI/CAN 372 and conforms with the lead content requirements
    for "lead free" plumbing as defined by California, Vermont, Maryland, and Louisiana
    state laws and the U.S. Safe Drinking Water Act.
[Q] This product meets the reduced Q test statistic criteria of 1 µg or 0.5 µg for lead per
    Section 9.5.1.1 of NSF/ANSI/CAN 61.